Commit Graph

21094 Commits

Author SHA1 Message Date
Amelie Delaunay a415083a11 usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS
This patch introduces a new parameter to activate external ID pin and valid
vbus level detection, required on STM32MP15 SoC to support dual role,
either in HS or FS.
The STM32MP15 SoC uses the GGPIO register to enable the level detection.
The level detector requires to be powered.
Also adds the params structures for STM32MP15 OTG HS and STM32MP1 OTG FS.

Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-03-15 11:06:39 +02:00
Hanjie Lin 1e355f21d3 usb: dwc3: Add Amlogic A1 DWC3 glue
Adds support for Amlogic A1 USB Control Glue HW.

The Amlogic A1 SoC Family embeds 1 USB Controllers:
- a DWC3 IP configured as Host for USB2 and USB3

A glue connects the controllers to the USB2 PHY of A1 SoC.

Signed-off-by: Yue Wang <yue.wang@amlogic.com>
Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-03-15 11:06:39 +02:00
Jassi Brar 48ba02b2e2 usb: gadget: add udc driver for max3420
The MAX3420 is USB2.0 only, UDC-over-SPI controller. This driver
also supports the peripheral mode of MAX3421.

Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-03-15 11:06:39 +02:00
Felipe Balbi 30ad6273ad usb: dwc3: trace: print enqueue/dequeue pointers too
By printing enqueue/dequeue pointers, we can make sure that our TRB
handling is correct. We've had a recent situation where we were not
always dequeueing all TRBs in an SG list and this helped figure out
what the problem was.

Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-03-15 11:06:39 +02:00
Pratham Pratap dad2aff3e8 usb: dwc3: gadget: Update chain bit correctly when using sg list
If scatter-gather operation is allowed, a large USB request is split
into multiple TRBs. For preparing TRBs for sg list, driver iterates
over the list and creates TRB for each sg and mark the chain bit to
false for the last sg. The current IOMMU driver is clubbing the list
of sgs which shares a page boundary into one and giving it to USB driver.
With this the number of sgs mapped it not equal to the the number of sgs
passed. Because of this USB driver is not marking the chain bit to false
since it couldn't iterate to the last sg. This patch addresses this issue
by marking the chain bit to false if it is the last mapped sg.

At a practical level, this patch resolves USB transfer stalls
seen with adb on dwc3 based db845c, pixel3 and other qcom
hardware after functionfs gadget added scatter-gather support
around v4.20.

Credit also to Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
who implemented a very similar fix to this issue.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org> #4.20+
Signed-off-by: Pratham Pratap <prathampratap@codeaurora.org>
[jstultz: Slight tweak to remove sg_is_last() usage, reworked
          commit message, minor comment tweak]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Link: https://lore.kernel.org/r/20200302214443.55783-1-john.stultz@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:58:16 +01:00
Eugeniu Rosca 1f8b39bc99 usb: core: port: do error out if usb_autopm_get_interface() fails
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:

On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
 > A revised search finds line 997 in drivers/usb/core/hub.c and lines
 > 216, 269 in drivers/usb/core/port.c.  (I didn't try looking in any
 > other directories.)  AFAICT all three of these should check the
 > return value, although a error message in the kernel log probably
 > isn't needed.

Factor out the usb_port_runtime_{resume,suspend}() changes into a
standalone patch to allow conflict-free porting on top of stable v3.9+.

[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org

Fixes: 971fcd492c ("usb: add runtime pm support for usb port device")
Cc: stable@vger.kernel.org # v3.9+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-3-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:58:16 +01:00
Eugeniu Rosca 60e3f6e4ac usb: core: hub: do error out if usb_autopm_get_interface() fails
Reviewing a fresh portion of coverity defects in USB core
(specifically CID 1458999), Alan Stern noted below in [1]:

On Tue, Feb 25, 2020 at 02:39:23PM -0500, Alan Stern wrote:
 > A revised search finds line 997 in drivers/usb/core/hub.c and lines
 > 216, 269 in drivers/usb/core/port.c.  (I didn't try looking in any
 > other directories.)  AFAICT all three of these should check the
 > return value, although a error message in the kernel log probably
 > isn't needed.

Factor out the usb_remove_device() change into a standalone patch to
allow conflict-free integration on top of the earliest stable branches.

[1] https://lore.kernel.org/lkml/Pine.LNX.4.44L0.2002251419120.1485-100000@iolanthe.rowland.org

Fixes: 253e05724f ("USB: add a "remove hardware" sysfs attribute")
Cc: stable@vger.kernel.org # v2.6.33+
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-2-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:58:16 +01:00
Eugeniu Rosca 63d6d7ed47 usb: core: hub: fix unhandled return by employing a void function
Address below Coverity complaint (Feb 25, 2020, 8:06 AM CET):

*** CID 1458999:  Error handling issues  (CHECKED_RETURN)
/drivers/usb/core/hub.c: 1869 in hub_probe()
1863
1864            if (id->driver_info & HUB_QUIRK_CHECK_PORT_AUTOSUSPEND)
1865                    hub->quirk_check_port_auto_suspend = 1;
1866
1867            if (id->driver_info & HUB_QUIRK_DISABLE_AUTOSUSPEND) {
1868                    hub->quirk_disable_autosuspend = 1;
 >>>     CID 1458999:  Error handling issues  (CHECKED_RETURN)
 >>>     Calling "usb_autopm_get_interface" without checking return value (as is done elsewhere 97 out of 111 times).
1869                    usb_autopm_get_interface(intf);
1870            }
1871
1872            if (hub_configure(hub, &desc->endpoint[0].desc) >= 0)
1873                    return 0;
1874

Rather than checking the return value of 'usb_autopm_get_interface()',
switch to the usb_autopm_get_interface_no_resume() API, as per:

On Tue, Feb 25, 2020 at 10:32:32AM -0500, Alan Stern wrote:
 ------ 8< ------
 > This change (i.e. 'ret = usb_autopm_get_interface') is not necessary,
 > because the resume operation cannot fail at this point (interfaces
 > are always powered-up during probe). A better solution would be to
 > call usb_autopm_get_interface_no_resume() instead.
 ------ 8< ------

Fixes: 1208f9e1d7 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub")
Cc: Hardik Gajjar <hgajjar@de.adit-jv.com>
Cc: stable@vger.kernel.org # v4.14+
Reported-by: scan-admin@coverity.com
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200226175036.14946-1-erosca@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:58:16 +01:00
Jim Lin 86d92f5465 usb: storage: Add quirk for Samsung Fit flash
Current driver has 240 (USB2.0) and 2048 (USB3.0) as max_sectors,
e.g., /sys/bus/scsi/devices/0:0:0:0/max_sectors

If data access times out, driver error handling will issue a port
reset.
Sometimes Samsung Fit (090C:1000) flash disk will not respond to
later Set Address or Get Descriptor command.

Adding this quirk to limit max_sectors to 64 sectors to avoid issue
occurring.

Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1583158895-31342-1-git-send-email-jilin@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:56:26 +01:00
Dan Lazewatsky b96ed52d78 usb: quirks: add NO_LPM quirk for Logitech Screen Share
LPM on the device appears to cause xHCI host controllers to claim
that there isn't enough bandwidth to support additional devices.

Signed-off-by: Dan Lazewatsky <dlaz@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.com>
Link: https://lore.kernel.org/r/20200226143438.1445-1-gustavo.padovan@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:56:26 +01:00
Marco Felsch f06947f275 usb: usb251xb: fix regulator probe and error handling
Commit 4d7201cda2 ("usb: usb251xb: add vdd supply support") didn't
covered the non-DT use-case and so the regualtor_enable() call during
probe will fail on those platforms. Also the commit didn't handled the
error case correctly.

Move devm_regulator_get() out of usb251xb_get_ofdata() to address the
1st issue. This can be done without worries because devm_regulator_get()
handles the non-DT use-case too. Add devm_add_action_or_reset() to
address the 2nd bug.

Fixes: 4d7201cda2 ("usb: usb251xb: add vdd supply support")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Acked-by: Richard Leitner <richard.leitner@skidata.com>
Link: https://lore.kernel.org/r/20200226072644.18490-1-m.felsch@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:56:26 +01:00
Peter Chen 4bf2dd6513 usb: cdns3: gadget: toggle cycle bit before reset endpoint
If there are TRBs pending during reset endpoint operation, the
DMA will advance after reset operation, but it isn't expected,
since the data is not yet available (For OUT, the data is not
yet available). After the data is ready, there won't be any
interrupt since the EP_TRADDR already points to next TRB entry
and doorbell is not set.

To fix it, it toggles cycle bit before reset operation, and restores
it after reset, it could avoid unexpected DMA advance due to
cycle bit is for software during the endpoint reset operation.

Fixes: 7733f6c32e ("usb: cdns3: Add Cadence USB3 DRD Driver")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-3-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:56:26 +01:00
Peter Chen 8a7c47fb72 usb: cdns3: gadget: link trb should point to next request
It has marked the dequeue trb as link trb, but its next segment
pointer is still itself, it causes the transfer can't go on. Fix
it by set its pointer as the trb address for the next request.

Fixes: f616c3bda4 ("usb: cdns3: Fix dequeue implementation")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200219141455.23257-2-peter.chen@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-04 10:56:25 +01:00
Greg Kroah-Hartman bab5417f5f USB: misc: iowarrior: add support for the 100 device
Add a new device id for the 100 devie.  It has 4 interfaces like the 28
and 28L devices but a larger endpoint so more I/O pins.

Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20200214161148.GA3963518@kroah.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-17 10:44:43 +01:00
Greg Kroah-Hartman 450c52c784 USB: fixes for v5.6-rc1
DWC3 learned that we can't always depend on Event Status bits. A
 problem was solved which would only surface with scatter list on IN
 endpoints.
 
 DWC2 got a fix for feature requests (both set and clear) and GetStatus
 request.
 
 The serial gadget got a fix for a TX stall bug.
 
 Composite framework now works better for SSP devices.
 -----BEGIN PGP SIGNATURE-----
 
 iQJFBAABCAAvFiEElLzh7wn96CXwjh2IzL64meEamQYFAl5FdDQRHGJhbGJpQGtl
 cm5lbC5vcmcACgkQzL64meEamQZ7bhAArOr7eVWligWztFcCRj1WjgeXBARK+oIZ
 MZGHwV3jTbmvEwlv5rAb13d3R5rkIIQshvk0dU+J0n9kiUPJntlwu41vSd5/JyqR
 V70oYJPuJqDbI1HpkUnzha9SgiZcKXtA1NhjQmk/NmfYXQmQq5M7lDgug8BuFBDX
 EbrFp8ScJZ4TExgseaOOmGNS5d2GpQCLxBc0Rqmou7/1lHfplUXU3d9tdMYjR2g3
 XJucNDNV/CfN0TlThlcnyYifH7B1AWMgs9uxVA1DxRFC6IsU4SsKIEyrtU7Lf5qO
 jSUBsLawiuGOPdbfwxi0LwKuzWSvrs9ZAIshHL9Gkw9v/kAoWPzrbewymi06Voql
 H2MmjPSzynV1I5syPJPZeNxjPYNJmuMusmYuhXa+zE2alRYRDQeIk8/2goTDzcdJ
 7WIPCH7NwMDxPA/KCI74lgrIdViaDN12KZUNwi54UL6IppwQHXx/zR4tes4eCSVU
 /1RIiD9eL7OysKmrUMLf4vofEkA0Mc3tZ88Uel7hUuIOKN/T+O+eHqWAhY1KM6nT
 QCa0Ko+Vq8ZqW5CKhyO6K+nG73Dbhf4vWIaEmGY+Hg1GG6wRVDTOeBfaQXbA2L8h
 q8Vqb+wVsE0BmvyIMrWlc/sHmYsCFMtbOOIyHqq7BjcLPbUcjrKA+gDbxaXFBJWd
 KDcnaUHATNE=
 =n8Hd
 -----END PGP SIGNATURE-----

Merge tag 'fixes-for-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus

Felipe writes:

USB: fixes for v5.6-rc1

DWC3 learned that we can't always depend on Event Status bits. A
problem was solved which would only surface with scatter list on IN
endpoints.

DWC2 got a fix for feature requests (both set and clear) and GetStatus
request.

The serial gadget got a fix for a TX stall bug.

Composite framework now works better for SSP devices.

* tag 'fixes-for-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb:
  usb: dwc3: debug: fix string position formatting mixup with ret and len
  usb: gadget: serial: fix Tx stall after buffer overflow
  usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags
  usb: dwc2: Fix SET/CLEAR_FEATURE and GET_STATUS flows
  usb: dwc2: Fix in ISOC request length checking
  usb: gadget: composite: Support more than 500mA MaxPower
  usb: gadget: composite: Fix bMaxPower for SuperSpeedPlus
  usb: gadget: u_audio: Fix high-speed max packet size
  usb: dwc3: gadget: Check for IOC/LST bit in TRB->ctrl fields
2020-02-13 08:31:21 -08:00
Greg Kroah-Hartman d593126a96 USB-serial fixes for 5.6-rc2
Here's a fix for a ch341 regression in 5.5 which people have started to
 hit, and a fix for a logic error in an ir-usb error path.
 
 Both have been in linux-next with no reported issues.
 
 Signed-off-by: Johan Hovold <johan@kernel.org>
 -----BEGIN PGP SIGNATURE-----
 
 iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCXkUsAQAKCRALxc3C7H1l
 CF+cAP9CPo+dy0rMGKPWkqGfLInimD6pMheJYe3gUZ4xgcbMkQEA+J3u3wYJQ7ND
 Ia/KRCMV+mvvQTv9skejnd5K94TsVQ8=
 =EY3I
 -----END PGP SIGNATURE-----

Merge tag 'usb-serial-5.6-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus

Johan writes:

USB-serial fixes for 5.6-rc2

Here's a fix for a ch341 regression in 5.5 which people have started to
hit, and a fix for a logic error in an ir-usb error path.

Both have been in linux-next with no reported issues.

Signed-off-by: Johan Hovold <johan@kernel.org>

* tag 'usb-serial-5.6-rc2' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
  USB: serial: ch341: fix receiver regression
  USB: serial: ir-usb: Silence harmless uninitialized variable warning
2020-02-13 04:53:29 -08:00
Michal Simek 57d7713196 usb: gadget: udc-xilinx: Fix xudc_stop() kernel-doc format
The patch removes "driver" parameter which has been removed without
updating kernel-doc format.

Fixes: 22835b807e ("usb: gadget: remove unnecessary 'driver' argument")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c753b529bdcdfdd40a3cf69121527ec8c63775cb.1581505183.git.michal.simek@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12 10:39:00 -08:00
Greg Kroah-Hartman 5f6f8da2d7 USB: misc: iowarrior: add support for the 28 and 28L devices
Add new device ids for the 28 and 28L devices.  These have 4 interfaces
instead of 2, but the driver binds the same, so the driver changes are
minimal.

Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12 09:54:26 -08:00
Greg Kroah-Hartman 461d8deb26 USB: misc: iowarrior: add support for 2 OEMed devices
Add support for two OEM devices that are identical to existing
IO-Warrior devices, except for the USB device id.

Cc: Christoph Jung <jung@codemercs.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212040422.2991-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12 09:54:23 -08:00
Richard Dodd b692056db8 USB: Fix novation SourceControl XL after suspend
Currently, the SourceControl will stay in power-down mode after resuming
from suspend. This patch resets the device after suspend to power it up.

Signed-off-by: Richard Dodd <richard.o.dodd@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200212142220.36892-1-richard.o.dodd@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12 09:54:07 -08:00
Mathias Nyman cf0ee7c60c xhci: Fix memory leak when caching protocol extended capability PSI tables - take 2
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.

Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.

To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.

When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.

Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20200211150158.14475-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12 09:51:09 -08:00
Greg Kroah-Hartman 67f68f977a Revert "xhci: Fix memory leak when caching protocol extended capability PSI tables"
This reverts commit fc57313d10.

Marek reports that it breaks things:
	This patch landed in today's linux-next (20200211) and causes
	NULL pointer dereference during second suspend/resume cycle on
	Samsung Exynos5422-based (arm 32bit) Odroid XU3lite board:

A more complete fix will be added soon.

Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Fixes: fc57313d10 ("xhci: Fix memory leak when caching protocol extended capability PSI tables")
Cc: Paul Menzel <pmenzel@molgen.mpg.de>
Cc: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Cc: stable <stable@vger.kernel.org> # v4.4+
Cc: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-12 09:48:57 -08:00
Colin Ian King 42cd5ffe46 usb: dwc3: debug: fix string position formatting mixup with ret and len
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.

Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Sergey Organov e4bfded56c usb: gadget: serial: fix Tx stall after buffer overflow
Symptom: application opens /dev/ttyGS0 and starts sending (writing) to
it while either USB cable is not connected, or nobody listens on the
other side of the cable. If driver circular buffer overflows before
connection is established, no data will be written to the USB layer
until/unless /dev/ttyGS0 is closed and re-opened again by the
application (the latter besides having no means of being notified about
the event of establishing of the connection.)

Fix: on open and/or connect, kick Tx to flush circular buffer data to
USB layer.

Signed-off-by: Sergey Organov <sorganov@gmail.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Lars-Peter Clausen 43d565727a usb: gadget: ffs: ffs_aio_cancel(): Save/restore IRQ flags
ffs_aio_cancel() can be called from both interrupt and thread context. Make
sure that the current IRQ state is saved and restored by using
spin_{un,}lock_irq{save,restore}().

Otherwise undefined behavior might occur.

Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Minas Harutyunyan 9a0d6f7c0a usb: dwc2: Fix SET/CLEAR_FEATURE and GET_STATUS flows
SET/CLEAR_FEATURE for Remote Wakeup allowance not handled correctly.
GET_STATUS handling provided not correct data on DATA Stage.
Issue seen when gadget's dr_mode set to "otg" mode and connected
to MacOS.
Both are fixed and tested using USBCV Ch.9 tests.

Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Fixes: fa389a6d77 ("usb: dwc2: gadget: Add remote_wakeup_allowed flag")
Tested-by: Jack Mitchell <ml@embed.me.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Minas Harutyunyan 860ef6cd3f usb: dwc2: Fix in ISOC request length checking
Moved ISOC request length checking from dwc2_hsotg_start_req() function to
dwc2_hsotg_ep_queue().

Fixes: 4fca54aa58 ("usb: gadget: s3c-hsotg: add multi count support")
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Jack Pham a2035411fa usb: gadget: composite: Support more than 500mA MaxPower
USB 3.x SuperSpeed peripherals can draw up to 900mA of VBUS power
when in configured state. However, if a configuration wanting to
take advantage of this is added with MaxPower greater than 500
(currently possible if using a ConfigFS gadget) the composite
driver fails to accommodate this for a couple reasons:

 - usb_gadget_vbus_draw() when called from set_config() and
   composite_resume() will be passed the MaxPower value without
   regard for the current connection speed, resulting in a
   violation for USB 2.0 since the max is 500mA.

 - the bMaxPower of the configuration descriptor would be
   incorrectly encoded, again if the connection speed is only
   at USB 2.0 or below, likely wrapping around U8_MAX since
   the 2mA multiplier corresponds to a maximum of 510mA.

Fix these by adding checks against the current gadget->speed
when the c->MaxPower value is used (set_config() and
composite_resume()) and appropriately limit based on whether
it is currently at a low-/full-/high- or super-speed connection.

Because 900 is not divisible by 8, with the round-up division
currently used in encode_bMaxPower() a MaxPower of 900mA will
result in an encoded value of 0x71. When a host stack (including
Linux and Windows) enumerates this on a single port root hub, it
reads this value back and decodes (multiplies by 8) to get 904mA
which is strictly greater than 900mA that is typically budgeted
for that port, causing it to reject the configuration. Instead,
we should be using the round-down behavior of normal integral
division so that 900 / 8 -> 0x70 or 896mA to stay within range.
And we might as well change it for the high/full/low case as well
for consistency.

N.B. USB 3.2 Gen N x 2 allows for up to 1500mA but there doesn't
seem to be any any peripheral controller supported by Linux that
does two lane operation, so for now keeping the clamp at 900
should be fine.

Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Jack Pham c724417baf usb: gadget: composite: Fix bMaxPower for SuperSpeedPlus
SuperSpeedPlus peripherals must report their bMaxPower of the
configuration descriptor in units of 8mA as per the USB 3.2
specification. The current switch statement in encode_bMaxPower()
only checks for USB_SPEED_SUPER but not USB_SPEED_SUPER_PLUS so
the latter falls back to USB 2.0 encoding which uses 2mA units.
Replace the switch with a simple if/else.

Fixes: eae5820b85 ("usb: gadget: composite: Write SuperSpeedPlus config descriptors")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
John Keeping 904967c60d usb: gadget: u_audio: Fix high-speed max packet size
Prior to commit eb9fecb9e6 ("usb: gadget: f_uac2: split out audio
core") the maximum packet size was calculated only from the high-speed
descriptor but now we use the largest of the full-speed and high-speed
descriptors.

This is correct, but the full-speed value is likely to be higher than
that for high-speed and this leads to submitting requests for OUT
transfers (received by the gadget) which are larger than the endpoint's
maximum packet size.  These are rightly rejected by the gadget core.

config_ep_by_speed() already sets up the correct maximum packet size for
the enumerated speed in the usb_ep structure, so we can simply use this
instead of the overall value that has been used to allocate buffers for
requests.

Note that the minimum period for ALSA is still set from the largest
value, and this is unavoidable because it's possible to open the audio
device before the gadget has been enumerated.

Tested-by: Pavel Hofman  <pavel.hofman@ivitera.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Anurag Kumar Vulisha 5ee858975b usb: dwc3: gadget: Check for IOC/LST bit in TRB->ctrl fields
The current code in dwc3_gadget_ep_reclaim_completed_trb() will
check for IOC/LST bit in the event->status and returns if
IOC/LST bit is set. This logic doesn't work if multiple TRBs
are queued per request and the IOC/LST bit is set on the last
TRB of that request.

Consider an example where a queued request has multiple queued
TRBs and IOC/LST bit is set only for the last TRB. In this case,
the core generates XferComplete/XferInProgress events only for
the last TRB (since IOC/LST are set only for the last TRB). As
per the logic in dwc3_gadget_ep_reclaim_completed_trb()
event->status is checked for IOC/LST bit and returns on the
first TRB. This leaves the remaining TRBs left unhandled.

Similarly, if the gadget function enqueues an unaligned request
with sglist already in it, it should fail the same way, since we
will append another TRB to something that already uses more than
one TRB.

To aviod this, this patch changes the code to check for IOC/LST
bits in TRB->ctrl instead.

At a practical level, this patch resolves USB transfer stalls seen
with adb on dwc3 based HiKey960 after functionfs gadget added
scatter-gather support around v4.20.

Cc: Felipe Balbi <balbi@kernel.org>
Cc: Yang Fei <fei.yang@intel.com>
Cc: Thinh Nguyen <thinhn@synopsys.com>
Cc: Tejas Joglekar <tejas.joglekar@synopsys.com>
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Cc: Jack Pham <jackp@codeaurora.org>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Linux USB List <linux-usb@vger.kernel.org>
Cc: stable <stable@vger.kernel.org>
Tested-by: Tejas Joglekar <tejas.joglekar@synopsys.com>
Reviewed-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
[jstultz: forward ported to mainline, reworded commit log, reworked
 to only check trb->ctrl as suggested by Felipe]
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
2020-02-11 08:45:45 +02:00
Johan Hovold 7f1b92a6a7 USB: core: clean up endpoint-descriptor parsing
Use the new usb-device pointer instead of back-casting when accessing
the struct usb_device when parsing endpoints.

Note that this introduces two lines that are longer than 80 chars on
purpose.

Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:14:22 -08:00
Johan Hovold bdd1b147b8 USB: quirks: blacklist duplicate ep on Sound Devices USBPre2
This device has a broken vendor-specific altsetting for interface 1,
where endpoint 0x85 is declared as an isochronous endpoint despite being
used by interface 2 for audio capture.

Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass          239 Miscellaneous Device
  bDeviceSubClass         2
  bDeviceProtocol         1 Interface Association
  bMaxPacketSize0        64
  idVendor           0x0926
  idProduct          0x0202
  bcdDevice            1.00
  iManufacturer           1 Sound Devices
  iProduct                2 USBPre2
  iSerial                 3 [...]
  bNumConfigurations      1

[...]

    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        1
      bAlternateSetting       3
      bNumEndpoints           2
      bInterfaceClass       255 Vendor Specific Class
      bInterfaceSubClass      0
      bInterfaceProtocol      0
      iInterface              0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            5
          Transfer Type            Isochronous
          Synch Type               Asynchronous
          Usage Type               Data
        wMaxPacketSize     0x0126  1x 294 bytes
        bInterval               1

[...]

    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        2
      bAlternateSetting       1
      bNumEndpoints           1
      bInterfaceClass         1 Audio
      bInterfaceSubClass      2 Streaming
      bInterfaceProtocol      0
      iInterface              0
      AudioStreaming Interface Descriptor:
        bLength                 7
        bDescriptorType        36
        bDescriptorSubtype      1 (AS_GENERAL)
        bTerminalLink           4
        bDelay                  1 frames
        wFormatTag         0x0001 PCM
      AudioStreaming Interface Descriptor:
        bLength                26
        bDescriptorType        36
        bDescriptorSubtype      2 (FORMAT_TYPE)
        bFormatType             1 (FORMAT_TYPE_I)
        bNrChannels             2
        bSubframeSize           2
        bBitResolution         16
        bSamFreqType            6 Discrete
        tSamFreq[ 0]         8000
        tSamFreq[ 1]        16000
        tSamFreq[ 2]        24000
        tSamFreq[ 3]        32000
        tSamFreq[ 4]        44100
        tSamFreq[ 5]        48000
      Endpoint Descriptor:
        bLength                 9
        bDescriptorType         5
        bEndpointAddress     0x85  EP 5 IN
        bmAttributes            5
          Transfer Type            Isochronous
          Synch Type               Asynchronous
          Usage Type               Data
        wMaxPacketSize     0x0126  1x 294 bytes
        bInterval               4
        bRefresh                0
        bSynchAddress           0
        AudioStreaming Endpoint Descriptor:
          bLength                 7
          bDescriptorType        37
          bDescriptorSubtype      1 (EP_GENERAL)
          bmAttributes         0x01
            Sampling Frequency
          bLockDelayUnits         2 Decoded PCM samples
          wLockDelay         0x0000

Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing, but in this case we need to ignore the first
instance in order to avoid breaking the audio capture interface.

Fixes: 3e4f8e21c4 ("USB: core: fix check for duplicate endpoints")
Cc: stable <stable@vger.kernel.org>
Reported-by: edes <edes@gmx.net>
Tested-by: edes <edes@gmx.net>
Link: https://lore.kernel.org/r/20200201105829.5682c887@acme7.acmenet
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:14:22 -08:00
Johan Hovold 73f8bda9b5 USB: core: add endpoint-blacklist quirk
Add a new device quirk that can be used to blacklist endpoints.

Since commit 3e4f8e21c4 ("USB: core: fix check for duplicate
endpoints") USB core ignores any duplicate endpoints found during
descriptor parsing.

In order to handle devices where the first interfaces with duplicate
endpoints are the ones that should have their endpoints ignored, we need
to add a blacklist.

Tested-by: edes <edes@gmx.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200203153830.26394-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:14:22 -08:00
Colin Ian King b32196e35b usb: dwc3: debug: fix string position formatting mixup with ret and len
Currently the string formatting is mixing up the offset of ret and
len. Re-work the code to use just len, remove ret and use scnprintf
instead of snprintf and len position accumulation where required.
Remove the -ve return check since scnprintf never returns a failure
-ve size. Also break overly long lines to clean up checkpatch
warnings.

Addresses-Coverity: ("Unused value")
Fixes: 1381a5113c ("usb: dwc3: debug: purge usage of strcat")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200210095139.328711-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:13:50 -08:00
Dmitry Osipenko a4a601948f usb: phy: tegra: Add clarifying comments about the shared registers
Tools like Coccinelle may erroneously recommend to use the
devm_platform_ioremap_resource() API for the registers mapping because
these tools are not aware about the implementation details of the driver.
Let's add a clarifying comments to the code, which should help to stop
future attempts to break the driver.

Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200202224259.29187-1-digetx@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:12:15 -08:00
Alan Stern 8099f58f1e USB: hub: Don't record a connect-change event during reset-resume
Paul Zimmerman reports that his USB Bluetooth adapter sometimes
crashes following system resume, when it receives a
Get-Device-Descriptor request while it is busy doing something else.

Such a request was added by commit a4f55d8b8c ("usb: hub: Check
device descriptor before resusciation").  It gets sent when the hub
driver's work thread checks whether a connect-change event on an
enabled port really indicates a new device has been connected, as
opposed to an old device momentarily disconnecting and then
reconnecting (which can happen with xHCI host controllers, since they
automatically enable connected ports).

The same kind of thing occurs when a port's power session is lost
during system suspend.  When the system wakes up it sees a
connect-change event on the port, and if the child device's
persist_enabled flag was set then hub_activate() sets the device's
reset_resume flag as well as the port's bit in hub->change_bits.  The
reset-resume code then takes responsibility for checking that the same
device is still attached to the port, and it does this as part of the
device's resume pathway.  By the time the hub driver's work thread
starts up again, the device has already been fully reinitialized and
is busy doing its own thing.  There's no need for the work thread to
do the same check a second time, and in fact this unnecessary check is
what caused the problem that Paul observed.

Note that performing the unnecessary check is not actually a bug.
Devices are supposed to be able to send descriptors back to the host
even when they are busy doing something else.  The underlying cause of
Paul's problem lies in his Bluetooth adapter.  Nevertheless, we
shouldn't perform the same check twice in a row -- and as a nice side
benefit, removing the extra check allows the Bluetooth adapter to work
more reliably.

The work thread performs its check when it sees that the port's bit is
set in hub->change_bits.  In this situation that bit is interpreted as
though a connect-change event had occurred on the port _after_ the
reset-resume, which is not what actually happened.

One possible fix would be to make the reset-resume code clear the
port's bit in hub->change_bits.  But it seems simpler to just avoid
setting the bit during hub_activate() in the first place.  That's what
this patch does.

(Proving that the patch is correct when CONFIG_PM is disabled requires
a little thought.  In that setting hub_activate() will be called only
for initialization and resets, since there won't be any resumes or
reset-resumes.  During initialization and hub resets the hub doesn't
have any child devices, and so this code path never gets executed.)

Reported-and-tested-by: Paul Zimmerman <pauldzim@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://marc.info/?t=157949360700001&r=1&w=2
CC: David Heinzelmann <heinzelmann.david@gmail.com>
CC: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.2001311037460.1577-100000@iolanthe.rowland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:08:30 -08:00
EJ Hsu 3e99862c05 usb: uas: fix a plug & unplug racing
When a uas disk is plugged into an external hub, uas_probe()
will be called by the hub thread to do the probe. It will
first create a SCSI host and then do the scan for this host.
During the scan, it will probe the LUN using SCSI INQUERY command
which will be packed in the URB and submitted to uas disk.

There might be a chance that this external hub with uas disk
attached is unplugged during the scan. In this case, uas driver
will fail to submit the URB (due to the NOTATTACHED state of uas
device) and try to put this SCSI command back to request queue
waiting for next chance to run.

In normal case, this cycle will terminate when hub thread gets
disconnection event and calls into uas_disconnect() accordingly.
But in this case, uas_disconnect() will not be called because
hub thread of external hub gets stuck waiting for the completion
of this SCSI command. A deadlock happened.

In this fix, uas will call scsi_scan_host() asynchronously to
avoid the blocking of hub thread.

Signed-off-by: EJ Hsu <ejh@nvidia.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200130092506.102760-1-ejh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:08:30 -08:00
Hardik Gajjar 1208f9e1d7 USB: hub: Fix the broken detection of USB3 device in SMSC hub
Renesas R-Car H3ULCB + Kingfisher Infotainment Board is either not able
to detect the USB3.0 mass storage devices or is detecting those as
USB2.0 high speed devices.

The explanation given by Renesas is that, due to a HW issue, the XHCI
driver does not wake up after going to sleep on connecting a USB3.0
device.

In order to mitigate that, disable the auto-suspend feature
specifically for SMSC hubs from hub_probe() function, as a quirk.

Renesas Kingfisher Infotainment Board has two USB3.0 ports (CN2) which
are connected via USB5534B 4-port SuperSpeed/Hi-Speed, low-power,
configurable hub controller.

[1] SanDisk USB 3.0 device detected as USB-2.0 before the patch
 [   74.036390] usb 5-1.1: new high-speed USB device number 4 using xhci-hcd
 [   74.061598] usb 5-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
 [   74.069976] usb 5-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
 [   74.077303] usb 5-1.1: Product: Ultra
 [   74.080980] usb 5-1.1: Manufacturer: SanDisk
 [   74.085263] usb 5-1.1: SerialNumber: 4C530001110208116550

[2] SanDisk USB 3.0 device detected as USB-3.0 after the patch
 [   34.565078] usb 6-1.1: new SuperSpeed Gen 1 USB device number 3 using xhci-hcd
 [   34.588719] usb 6-1.1: New USB device found, idVendor=0781, idProduct=5581, bcdDevice= 1.00
 [   34.597098] usb 6-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
 [   34.604430] usb 6-1.1: Product: Ultra
 [   34.608110] usb 6-1.1: Manufacturer: SanDisk
 [   34.612397] usb 6-1.1: SerialNumber: 4C530001110208116550

Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1580989763-32291-1-git-send-email-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 11:08:26 -08:00
Mathias Nyman a3ae87dce3 xhci: apply XHCI_PME_STUCK_QUIRK to Intel Comet Lake platforms
Intel Comet Lake based platform require the XHCI_PME_STUCK_QUIRK
quirk as well. Without this xHC can not enter D3 in runtime suspend.

Cc: stable@vger.kernel.org
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 06:56:22 -08:00
Mathias Nyman 024d411e9c xhci: fix runtime pm enabling for quirky Intel hosts
Intel hosts that need the XHCI_PME_STUCK_QUIRK flag should enable
runtime pm by calling xhci_pme_acpi_rtd3_enable() before
usb_hcd_pci_probe() calls pci_dev_run_wake().
Otherwise usage count for the device won't be decreased, and runtime
suspend is prevented.

usb_hcd_pci_probe() only decreases the usage count if device can
generate run-time wake-up events, i.e. when pci_dev_run_wake()
returns true.

This issue was exposed by pci_dev_run_wake() change in
commit 8feaec33b9 ("PCI / PM: Always check PME wakeup capability for
runtime wakeup support")
and should be backported to kernels with that change

Cc: <stable@vger.kernel.org> # 4.13+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 06:56:21 -08:00
Mathias Nyman fc57313d10 xhci: Fix memory leak when caching protocol extended capability PSI tables
xhci driver assumed that xHC controllers have at most one custom
supported speed table (PSI) for all usb 3.x ports.
Memory was allocated for one PSI table under the xhci hub structure.

Turns out this is not the case, some controllers have a separate
"supported protocol capability" entry with a PSI table for each port.
This means each usb3 roothub port can in theory support different custom
speeds.

To solve this, cache all supported protocol capabilities with their PSI
tables in an array, and add pointers to the xhci port structure so that
every port points to its capability entry in the array.

When creating the SuperSpeedPlus USB Device Capability BOS descriptor
for the xhci USB 3.1 roothub we for now will use only data from the
first USB 3.1 capable protocol capability entry in the array.
This could be improved later, this patch focuses resolving
the memory leak.

Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@amd.com>
Fixes: 47189098f8 ("xhci: parse xhci protocol speed ID list for usb 3.1 usage")
Cc: stable <stable@vger.kernel.org> # v4.4+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 06:56:21 -08:00
Mathias Nyman f148b9f402 xhci: Force Maximum Packet size for Full-speed bulk devices to valid range.
A Full-speed bulk USB audio device (DJ-Tech CTRL) with a invalid Maximum
Packet Size of 4 causes a xHC "Parameter Error" at enumeration.

This is because valid Maximum packet sizes for Full-speed bulk endpoints
are 8, 16, 32 and 64 bytes. Hosts are not required to support other values
than these. See usb 2 specs section 5.8.3 for details.

The device starts working after forcing the maximum packet size to 8.
This is most likely the case with other devices as well, so force the
maximum packet size to a valid range.

Cc: stable@vger.kernel.org
Reported-by: Rene D Obermueller <cmdrrdo@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20200210134553.9144-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-02-10 06:56:20 -08:00
Johan Hovold 7c3d02285a USB: serial: ch341: fix receiver regression
While assumed not to make a difference, not using the factor-2 prescaler
makes the receiver more susceptible to errors.

Specifically, there have been reports of problems with devices that
cannot generate a 115200 rate with a smaller error than 2.1% (e.g.
117647 bps). But this can also be reproduced with a low-speed RS232
tranceiver at 115200 when the input rate matches the nominal rate.

So whenever possible, enable the factor-2 prescaler and halve the
divisor in order to use settings closer to that of the previous
algorithm.

Fixes: 3571456508 ("USB: serial: ch341: reimplement line-speed handling")
Cc: stable <stable@vger.kernel.org>	# 5.5
Reported-by: Jakub Nantl <jn@forever.cz>
Tested-by: Jakub Nantl <jn@forever.cz>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
2020-02-10 10:10:35 +01:00
Dan Carpenter c664a4fa8f USB: serial: ir-usb: Silence harmless uninitialized variable warning
The "actual_length" variable might be uninitialized on some failure
paths.  It's harmless but static analysis tools like Smatch complain
and at runtime the UBSan tool will likely complain as well.

Fixes: e7542bc382 ("USB: serial: ir-usb: make set_termios synchronous")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
2020-02-10 10:06:51 +01:00
Linus Torvalds c9d35ee049 Merge branch 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs file system parameter updates from Al Viro:
 "Saner fs_parser.c guts and data structures. The system-wide registry
  of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
  the horror switch() in fs_parse() that would have to grow another case
  every time something got added to that system-wide registry.

  New syntax types can be added by filesystems easily now, and their
  namespace is that of functions - not of system-wide enum members. IOW,
  they can be shared or kept private and if some turn out to be widely
  useful, we can make them common library helpers, etc., without having
  to do anything whatsoever to fs_parse() itself.

  And we already get that kind of requests - the thing that finally
  pushed me into doing that was "oh, and let's add one for timeouts -
  things like 15s or 2h". If some filesystem really wants that, let them
  do it. Without somebody having to play gatekeeper for the variants
  blessed by direct support in fs_parse(), TYVM.

  Quite a bit of boilerplate is gone. And IMO the data structures make a
  lot more sense now. -200LoC, while we are at it"

* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
  tmpfs: switch to use of invalfc()
  cgroup1: switch to use of errorfc() et.al.
  procfs: switch to use of invalfc()
  hugetlbfs: switch to use of invalfc()
  cramfs: switch to use of errofc() et.al.
  gfs2: switch to use of errorfc() et.al.
  fuse: switch to use errorfc() et.al.
  ceph: use errorfc() and friends instead of spelling the prefix out
  prefix-handling analogues of errorf() and friends
  turn fs_param_is_... into functions
  fs_parse: handle optional arguments sanely
  fs_parse: fold fs_parameter_desc/fs_parameter_spec
  fs_parser: remove fs_parameter_description name field
  add prefix to fs_context->log
  ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
  new primitive: __fs_parse()
  switch rbd and libceph to p_log-based primitives
  struct p_log, variants of warnf() et.al. taking that one instead
  teach logfc() to handle prefices, give it saner calling conventions
  get rid of cg_invalf()
  ...
2020-02-08 13:26:41 -08:00
Al Viro d7167b1499 fs_parse: fold fs_parameter_desc/fs_parameter_spec
The former contains nothing but a pointer to an array of the latter...

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2020-02-07 14:48:37 -05:00
Eric Sandeen 96cafb9ccb fs_parser: remove fs_parameter_description name field
Unused now.

Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2020-02-07 14:48:36 -05:00
Alexey Dobriyan 97a32539b9 proc: convert everything to "struct proc_ops"
The most notable change is DEFINE_SHOW_ATTRIBUTE macro split in
seq_file.h.

Conversion rule is:

	llseek		=> proc_lseek
	unlocked_ioctl	=> proc_ioctl

	xxx		=> proc_xxx

	delete ".owner = THIS_MODULE" line

[akpm@linux-foundation.org: fix drivers/isdn/capi/kcapi_proc.c]
[sfr@canb.auug.org.au: fix kernel/sched/psi.c]
  Link: http://lkml.kernel.org/r/20200122180545.36222f50@canb.auug.org.au
Link: http://lkml.kernel.org/r/20191225172546.GB13378@avx2
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2020-02-04 03:05:26 +00:00
Linus Torvalds aac9662671 USB/Thunderbolt/PHY driver updates for 5.6-rc1
Here is the big USB and Thunderbolt and PHY driver updates for 5.6-rc1.
 
 With the advent of USB4, "Thunderbolt" has really become USB4, so the
 renaming of the Kconfig option and starting to share subsystem code has
 begun, hence both subsystems coming in through the same tree here.
 
 PHY driver updates also touched USB drivers, so that is coming in
 through here as well.
 
 Major stuff included in here are:
 	- USB 4 initial support added (i.e. Thunderbolt)
 	- musb driver updates
 	- USB gadget driver updates
 	- PHY driver updates
 	- USB PHY driver updates
 	- lots of USB serial stuff fixed up
 	- USB typec updates
 	- USB-IP fixes
 	- lots of other smaller USB driver updates
 
 All of these have been in linux-next for a while now (the usb-serial
 tree is already tested in linux-next on its own before merged into
 here), with no reported issues.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXjFTNw8cZ3JlZ0Brcm9h
 aC5jb20ACgkQMUfUDdst+ynpKQCgrh2FoobS2x0oFg/OUHdjokQV/BYAoJGWLOmt
 8S5cnsCuLq3w5qpCcBva
 =PMGd
 -----END PGP SIGNATURE-----

Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/Thunderbolt/PHY driver updates from Greg KH:
 "Here is the big USB and Thunderbolt and PHY driver updates for
  5.6-rc1.

  With the advent of USB4, "Thunderbolt" has really become USB4, so the
  renaming of the Kconfig option and starting to share subsystem code
  has begun, hence both subsystems coming in through the same tree here.

  PHY driver updates also touched USB drivers, so that is coming in
  through here as well.

  Major stuff included in here are:
   - USB 4 initial support added (i.e. Thunderbolt)
   - musb driver updates
   - USB gadget driver updates
   - PHY driver updates
   - USB PHY driver updates
   - lots of USB serial stuff fixed up
   - USB typec updates
   - USB-IP fixes
   - lots of other smaller USB driver updates

  All of these have been in linux-next for a while now (the usb-serial
  tree is already tested in linux-next on its own before merged into
  here), with no reported issues"

[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
  that causes configuration warnings    - Linus ]

* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
  Doc: ABI: add usb charger uevent
  usb: phy: show USB charger type for user
  usb: cdns3: fix spelling mistake and rework grammar in text
  usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
  USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
  USB: serial: ir-usb: simplify endpoint check
  USB: serial: ir-usb: make set_termios synchronous
  USB: serial: ir-usb: fix IrLAP framing
  USB: serial: ir-usb: fix link-speed handling
  USB: serial: ir-usb: add missing endpoint sanity check
  usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
  usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
  usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
  usb: typec: tcpci: mask event interrupts when remove driver
  usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
  usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
  usb: chipidea: handle single role for usb role class
  usb: musb: fix spelling mistake: "periperal" -> "peripheral"
  phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
  USB: usbfs: Always unlink URBs in reverse order
  ...
2020-01-29 10:09:44 -08:00