lan9303_handle_reset never returns anything other than success.
So there's not need for it to return an error code.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is a problem with the VTU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is a problem with the ATU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENODEV from the chip not found error handling
case instead of 0(ret have been overwritten to 0 by lan9303_read()), as
done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify calculation of chip->phy_addr_base in lan9303_detect_phy_setup().
Use GENMASK to calculate phys_mii_mask from LAN9303_NUM_PORTS and
phy_addr_base.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
chip->phy_addr_sel_strap is declared as a bool, but is also used as an
integer address base.
Rename 'phy_addr_sel_strap' to 'phy_addr_base', and change type to int.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Models such as BCM5395/97/98 and BCM53125/24/53115 and compatible require that
we turn on managed mode to actually act on Broadcom tags, otherwise they just
pass them through on ingress (host -> switch) and don't insert them in egress
(switch -> host). Turning on managed mode is simple, but requires us to
properly support ARL misses on multicast addresses which is a much more
involved set of changes not suitable for a bug fix for this release.
Reported-by: Jochen Friedrich <jochen@scram.de>
Fixes: 7edc58d614 ("net: dsa: b53: Turn on Broadcom tags")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Non-functional cleanups in lan9303_csr_reg_wait():
- Change type of param 'mask' from int to u32.
- Remove param 'value' (will probably never be used)
- Reduced retries from 1000 to 25, consistent with lan9303_read_wait.
- Removed comments
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Changes v1 -> v2:
- Removed comments
Signed-off-by: David S. Miller <davem@davemloft.net>
Three sets of overlapping changes, two in the packet scheduler
and one in the meson-gxl PHY driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the compatible string and Device Tree binding document for
7278B0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MT7530 can treat each port as either VLAN-unaware port or VLAN-aware port
through the implementation of port matrix mode or port security mode on
the ingress port, respectively. On one hand, Each port has been acting as
the VLAN-unaware one whenever the device is created in the initial or
certain port joins or leaves into/from the bridge at the runtime. On the
other hand, the patch just filling the required callbacks for VLAN
operations is achieved via extending the port to be into port security
mode when the port is configured as VLAN-aware port. Which mode can make
the port be able to recognize VID from incoming packets and look up VLAN
table to validate and judge which port it should be going to. And the
range for VID from 1 to 4094 is valid for the hardware.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify lan9303_indirect_phy_wait_for_completion()
and lan9303_switch_wait_for_completion() by using a new function
lan9303_read_wait()
Changes v1 -> v2:
- param 'mask' type u32
- removed param 'value' (will probably never be used)
- add newline before return
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMII is a 32-bit bus plus two clock signals per direction. XAUI is
four serial lanes per direction. The 88e6190 supports XAUI but not
XGMII as it doesn't have enough pins. The same is true of 88e6176.
Match on PHY_INTERFACE_MODE_XAUI for the XAUI port type, but keep
accepting XGMII for backwards compatibility.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALR table operations are a sequence of related register operations which
should be protected from concurrent access. The alr_cache should also be
protected. Add alr_mutex doing that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MDIO busses need to be unregistered before they are freed,
otherwise BUG() is called. Add a call to the unregister code if the
registration fails, since we can have multiple busses, of which some
may correctly register before one fails. This requires moving the code
around a little.
Fixes: a3c53be55c ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing the interrupt handling code, we should mask the
generation of interrupts. The code however unmasked all
interrupts. This can then cause a new interrupt. We then get into a
deadlock where the interrupt thread is waiting to run, and the code
continues, trying to remove the interrupt handler, which means waiting
for the thread to complete. On a UP machine this deadlocks.
Fix so we really mask interrupts in the hardware. The same error is
made in the error path when install the interrupt handling code.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These duplicate includes have been found with scripts/checkincludes.pl but
they have been removed manually to avoid removing false positives.
Signed-off-by: Pravin Shedge <pravin.shedge4linux@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_upstream_port() helper still assumes a unique CPU port
in the whole switch fabric. This is becoming wrong, as every port in the
fabric has its dedicated CPU port, thus every port has an upstream port.
Add a port argument to the dsa_upstream_port() helper and fetch its CPU
port instead of the deprecated unique fabric CPU port. A CPU or unused
port has no dedicated CPU port, so return itself in this case.
At the same time, change the return value from u8 to unsigned int since
there is no need to limit the size here.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the setup of the global upstream port within the
mv88e6xxx_setup_upstream_port function.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper function to setup the upstream port of a given port.
This is the port used to reach the dedicated CPU port. This function
will be extended later to setup the global upstream port as well.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx driver currently assumes a single CPU port in the fabric
and thus floods frames with unknown DA on a single DSA port, the one
that is one hop closer to the CPU port.
With multiple CPU ports in mind, this isn't true anymore because CPU
ports could be found behind both DSA ports of a device in-between
others.
For example in a A <-> B <-> C fabric, both A and C having CPU ports,
device B will have to flood such frame to its two DSA ports.
This patch considers both CPU and DSA ports of a device as upstream
ports, where to flood frames with unknown DA addresses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Small overlapping change conflict ('net' changed a line,
'net-next' added a line right afterwards) in flexcan.c
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from MDB prepare and add operations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.
Remove the trans argument from VLAN prepare and add operations.
At the same time, fix the following checkpatch warning:
WARNING: line over 80 characters
#74: FILE: drivers/net/dsa/dsa_loop.c:177:
+ const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring an IPv6 address mask, we should use SLICE_NUM_MASK as
the mask in order to make sure all bits are masked by the hardware.
Also, we want matching entries to have a CHAIN_ID value set to the same
value as the rule index we return to user-space for convenience, so fix
that too.
Fixes: ba0696c22e ("net: dsa: bcm_sf2: Add support for IPv6 CFP rules")
Fixes: dd8eff6834 ("net: dsa: bcm_sf2: Allow matching arbitrary IPv6 masks/lengths")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Utilize the much more capable b53_get_tag_protocol() which takes care of
all Broadcom switches specifics to resolve which port can have Broadcom
tags enabled or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
- The final conversion of timer wheel timers to timer_setup().
A few manual conversions and a large coccinelle assisted sweep and
the removal of the old initialization mechanisms and the related
code.
- Remove the now unused VSYSCALL update code
- Fix permissions of /proc/timer_list. I still need to get rid of that
file completely
- Rename a misnomed clocksource function and remove a stale declaration
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (27 commits)
m68k/macboing: Fix missed timer callback assignment
treewide: Remove TIMER_FUNC_TYPE and TIMER_DATA_TYPE casts
timer: Remove redundant __setup_timer*() macros
timer: Pass function down to initialization routines
timer: Remove unused data arguments from macros
timer: Switch callback prototype to take struct timer_list * argument
timer: Pass timer_list pointer to callbacks unconditionally
Coccinelle: Remove setup_timer.cocci
timer: Remove setup_*timer() interface
timer: Remove init_timer() interface
treewide: setup_timer() -> timer_setup() (2 field)
treewide: setup_timer() -> timer_setup()
treewide: init_timer() -> setup_timer()
treewide: Switch DEFINE_TIMER callbacks to struct timer_list *
s390: cmm: Convert timers to use timer_setup()
lightnvm: Convert timers to use timer_setup()
drivers/net: cris: Convert timers to use timer_setup()
drm/vc4: Convert timers to use timer_setup()
block/laptop_mode: Convert timers to use timer_setup()
net/atm/mpc: Avoid open-coded assignment of timer callback function
...
The PHY on BCM7278 has an additional bit that needs to be cleared:
IDDQ_GLOBAL_PWR, without doing this, the PHY remains stuck in reset out
of suspend/resume cycles.
Fixes: 0fe9933804 ("net: dsa: bcm_sf2: Add support for BCM7278 integrated switch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function devm_gpiod_get_optional() returns an ERR_PTR on failure. Its
return value should not be validated by a NULL check. Instead, use IS_ERR.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
On BCM58xx devices (Northstar Plus), there is an accelerator attached to
port 8 which would only work if we use prepended Broadcom tags. Resolve
that difference in our get_tag_protocol() function by setting the
appropriate tagging protocol in that case. We need to change
b53_brcm_hdr_setup() a little bit now since we can deal with two types
of Broadcom tags.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix embarrassing bug in lan9303_alr_del_port(): Instead of zeroing
entr->mac_addr, I destroyed the next cache entry. Affected .port_fdb_del and
.port_mdb_del.
Fixes: 0620427ea0 ("net: dsa: lan9303: Add fdb/mdb manipulation")
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable Broadcom tags for b53 devices, except 5325 and 5365 which use a
different Broadcom tag format not yet supported by net/dsa/tag_brcm.c.
We also make sure that we can turn on Broadcom tags on a CPU port number
that is capable of that: 5, 7 or 8.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev->cpu_port is the driver local information that should only be used
to look up register offsets for a particular port, when they differ
(e.g: IMP port override), but it should certainly not be used in place
of the DSA configured CPU port.
Since the DSA switch layer calls port_vlan_{add,del}() on the CPU port
as well, we can remove the specific setting of the CPU port within
port_vlan_{add,del}.
Fixes: ff39c2d686 ("net: dsa: b53: Add bridge support")
Fixes: 967dd82ffc ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
IGMP packets should be trapped to the CPU port. The SW bridge knows
whether to forward to other ports.
With "IGMP snooping for local traffic" merged, IGMP trapping is also
required for stable IGMPv2 operation.
LAN9303 does not trap IGMP packets by default.
Enable IGMP trapping in lan9303_setup.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics histogram mode was not being explicitly initialized on
devices other than the 6390 family. Clearing the statistics then
overwrote the default setting, setting the histogram to a reserved
mode.
Explicitly set the histogram mode for all devices. Change the
statistics clear into a read/modify/write, and since it is now more
complex, move it into global1.c.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the switch does not flood broadcast frames. Instead the
broadcast address is unknown in the ATU, so the frame gets forwarded
out the cpu port. The software bridge then floods it back to the
individual switch ports which are members of the bridge.
Add an ATU entry in the switch so that it floods broadcast frames out
ports, rather than have the software bridge do it. Also, send a copy
out the cpu port and any dsa ports. Rely on the port vectors to
prevent broadcast frames leaking between bridges, and separated ports.
Additionally, when a VLAN is added, a new FID is allocated. This
represents a new table of ATU entries. A broadcast entry is added to
the new FID.
With offload_fwd_mark being set, the software bridge will not flood
the frames it receives back to the switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function is going to be needed by a soon to be added new
function. Move it earlier so we can avoid a forward declaration.
No functional changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When testing if a VLAN is one more than one bridge, we print an error
message that the VLAN is already in use somewhere else. Print both the
new port which would like the VLAN, and the port which already has it,
to aid debugging.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the same VLAN on multiple bridges is currently unsupported as
an offload. mv88e6xxx_port_check_hw_vlan() is used to ensure that a
VLAN is not on multiple bridges when adding a VLAN range to a port. It
loops the ports and checks to see if there are ports in a different
bridge with the same VLAN.
While walking all switch ports, the code was checking if the new port
has a netdev slave attached to it. If not, skip checking the port
being walked. This seems like a typ0. If the new port does not have a
slave, how has a VLAN been added to it in the first place, requiring
this check be performed at all? More likely, we should be checking if
the port being walked has a slave. Without the port having a slave, it
cannot have a VLAN on it, so there is no need to check further for
that particular port.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ds->num_ports is 3, there is no need to check range of "port"
parameter.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove scripts/checkpatch.pl CHECKs by adjusting indenting.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove scripts/checkpatch.pl WARNING by replacing msleep(1) with usleep_range()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.
Add an ALR entry with STP state override to fix that.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have b53_hdr_setup() check what kind of tagging protocol is configured
(Broadcom or none) and apply the correct settings in both cases.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 replicate the same operations: clear all VLANs and set
their ports to the default VLAN tag (1 for these devices) so export the
b53 function doing just that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The unused ports are currently configured in normal mode. This does not
prevent the switch from being functional, but it is unnecessary. Skip
unused ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The next patch require net/dsa/tag_lan9303.c to access struct lan9303.
Therefore move struct lan9303 definitions from drivers/net/dsa/lan9303.h
to new file include/linux/dsa/lan9303.h.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the LAN9303 work when lan9303_probe() is called twice.
For some unknown reason the LAN9303 switch fail to forward data when switch
fabric port 0 TX is disabled during probe. (Write of LAN9303_MAC_TX_CFG_0
in lan9303_disable_processing_port().)
In that situation the switch fabric seem to receive frames, because the ALR
is learning addresses. But no frames are transmitted on any of the ports.
In our system lan9303_probe() is called twice, first time
dsa_register_switch() return -EPROBE_DEFER. As an experiment, modified the
code to skip writing LAN9303_MAC_TX_CFG_0, port 0 during the first probe.
Then the switch works as expected.
Resolve the problem by not calling lan9303_disable_processing_port() on
port 0 during probe. Ports 1 and 2 are still disabled.
Although unsatisfying that the exact failure mechanism is not known,
the patch should not cause any harm.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason why we should limit ourselves to matching only
full IPv4 addresses (/32), the same logic applies between the DATA and
MASK ports, so just make it more configurable to accept both.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason why we should limit ourselves to matching only full
IPv4 addresses (/32), the same logic applies between the DATA and MASK
ports, so just make it more configurable to accept both.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Inserting IPv6 CFP rules complicates the code a little bit in that we
need to insert two rules side by side and chain them to match a full
IPv6 tuple (src, dst IPv6 + port + protocol).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to do a HW search of the TCAMs which is something slow
and expensive. Since we already maintain a bitmask of active CFP rules,
just iterate over those, starting from bit 1 (after the reserved entry)
to get a count and index position to store the rule later on.
As a result we can remove the code in bcm_sf2_cfp_rule_get() which acted
on the "search" argument, and remove that argument.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for introducing IPv6 rules support, make the
cfp_udf_layout more flexible and match more accurately how the HW is
designed: we have 3 + 1 slices per protocol, but we may not be using all
of them and we are relative to a particular base offset (slice A for
IPv4 for instance). Also populate the slice number that should be used
(slice 1 for IPv4) based on the lookup function.
Finally, we introduce two helper functions: udf_upper_bits() and
udf_lower_bits() to help setting the UDF_n_* valid bits based on the
number of UDFs valid within a slice. Update the IPv4 rule setting to
make use of it to be more robust wrt. change in number of User Defined
Fields being programmed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the processing of IPv4 rules into specific functions, allowing us
to clearly identify which parts are generic and which ones are not. Also
create a specific function to insert a rule into the action and policer
RAMs as those tend to be fairly generic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of open coding the shift for the IP protocol, IP fragment bit
etc. define and/or use existing constants to that end.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add functions for managing the lan9303 ALR (Address Logic
Resolution).
Implement DSA methods: port_fdb_add, port_fdb_del, port_mdb_prepare,
port_mdb_add and port_mdb_del.
Since the lan9303 do not offer reading specific ALR entry, the driver
caches all static entries - in a flat table.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DSA method port_fast_age as a step to STP support.
Add low level functions for accessing the lan9303 ALR (Address Logic
Resolution).
Added DSA method port_fdb_dump
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure is part of DSA core data and must only be updated
by the later. It is OK and sometimes necessary for the DSA drivers to
access this data, but this has to be read only.
For that purpose, add a dsa_to_port() helper which returns a const
pointer to a dsa_port structure which must be used by DSA drivers from
now on instead of digging into ds->ports[] themselves.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dsa_port structure has a "netdev" member, which can be used for
either the master device, or the slave device, depending on its type.
It is true that today, CPU port are not exposed to userspace, thus the
port's netdev member can be used to point to its master interface.
But it is still slightly confusing, so split it into more explicit
"master" and "slave" members inside an anonymous union.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .set_addr function does nothing, remove the dsa_loop implementation
before getting rid of it completely in DSA.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for mv88e6xxx, setup the switch from within the mv88e6060 driver with
a random MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6060 Ethernet switch always transmits the multicast bit of the
switch MAC address as a zero. It re-uses the corresponding bit 8 of the
register "Switch MAC Address Register Bytes 0 & 1" for "DiffAddr".
If the "DiffAddr" bit is 0, then all ports transmit the same source
address. If it is set to 1, then bit 2:0 are used for the port number.
The mv88e6060 driver is currently wrongly shifting the MAC address byte
0 by 9. To fix this, shift it by 8 as usual and clear its bit 0.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
An Ethernet switch may support having a MAC address, which can be used
as the switch's source address in transmitted full-duplex Pause frames.
If a DSA switch supports the related .set_addr operation, the DSA core
sets the master's MAC address on the switch. This won't make sense
anymore in a multi-CPU ports system, because there won't be a unique
master device assigned to a switch tree.
Instead, setup the switch from within the Marvell driver with a random
MAC address, and remove the .set_addr implementation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turn on the out of band Advanced Congestion Buffering (ACB) mechanism at
the switch level now that we have properly established the queue mapping
between the switch egress queues and the SYSTEMPORT egress queues. This
allows the switch to correctly backpressure the host system when one of
its queue drops below the configured thresholds.
This is also helping achieve so called "lossless" behavior by adapting
the TX interrupt pacing to the actual speed and capacity of the switch
port.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When both user ports are joined to the same bridge, the normal
HW MAC learning is enabled. This means that unicast traffic is forwarded
in HW.
If one of the user ports leave the bridge,
the ports goes back to the initial separated operation.
Port separation relies on disabled HW MAC learning. Hence the condition
that both ports must join same bridge.
Add brigde methods port_bridge_join, port_bridge_leave and
port_stp_state_set.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare for next patch:
Move tag setup from lan9303_separate_ports() to new function
lan9303_setup_tagging()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mt7530_phy_write is local to the source and does not need to
be in global scope, so make it static.
Cleans up sparse warnings:
symbol 'mt7530_phy_write' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The functions lan9303_mdio_phy_write and lan9303_mdio_phy_read are local
to the source and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'lan9303_mdio_phy_write' was not declared. Should it be static?
symbol 'lan9303_mdio_phy_read' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e85ec74ace ("net: dsa: bcm_sf2: Defer port
enabling to calling port_enable") because this now makes an unbind
followed by a bind to fail connecting to the ingrated PHY.
What this patch missed is that we need the PHY to be enabled with
bcm_sf2_gphy_enable_set() before probing it on the MDIO bus. This is
correctly done in the ops->setup() function, but by the time
ops->port_enable() runs, this is too late. Upon unbind we would power
down the PHY, and so when we would bind again, the PHY would be left
powered off.
Fixes: e85ec74ace ("net: dsa: bcm_sf2: Defer port enabling to calling port_enable")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_g2_irq_free locks the registers mutex, but not
mv88e6xxx_g1_irq_free, which results in a stack trace from
assert_reg_lock when unloading the mv88e6xxx module. Fix this.
Fixes: 3460a5770c ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ports with the same VLAN must all be in the same bridge. However the
CPU and DSA ports need to be in multiple VLANs spread over multiple
bridges. So exclude them when performing this test.
Fixes: b2f81d304c ("net: dsa: add CPU and DSA ports as VLAN members")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each port in DSA has its own dedicated CPU port currently available in
its parent switch's ds->ports[port].cpu_dp. Use it instead of getting
the unique tree CPU port, which will be deprecated soon.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the driver react to device tree "fixed-link" declaration on CPU port.
- turn off autonegotiation
- force speed 10 or 100 mb/s
- force duplex mode
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Export b53_{enable,disable}_port and use these two functions in
bcm_sf2_port_setup and bcm_sf2_port_disable. The generic functions
cannot be used without wrapping because we need to manage additional
switch integration details (PHY, Broadcom tag etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The magic number 8 in 3 locations in bcm_sf2_cfp.c actually designates
the number of switch port egress queues, so use that define instead of
open-coding it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcm_sf2 and b53 do exactly the same thing, so share that piece.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for enabling and disabling EEE, as well as re-negotiating it in
.adjust_link() and in .port_enable().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the bcm_sf2 EEE-related functions to the b53 driver because this is shared
code amongst Gigabit capable switch, only 5325 and 5365 are too old to support
that.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for migrating the EEE code from bcm_sf2 to b53, define the full
EEE register page and offsets within that page.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to enable Broadcom tags/headers is largely switch independent,
and in preparation for enabling it for multiple devices with b53, move
the code we have in bcm_sf2.c to b53_common.c
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of repeating the same pattern: acquire mutex, read/write,
release mutex, define a macro: b53_build_op() which takes the type
(read|write), I/O size, and value (scalar or pointer). This helps with
fixing bugs that could exist (e.g: missing barrier, lock etc.).
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to configure the enabled ports once in bcm_sf2_sw_setup() and
then a second time around when dsa_switch_ops::port_enable is called, just do
it when port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to configure the enabled ports once in b53_setup() and then a
second time around when dsa_switch_ops::port_enable is called, just do it when
port_enable is called which is better in terms of power consumption and
correctness.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for future changes allowing the configuring of multiple
CPU ports, make b53_enable_cpu_port() take a port argument.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is not used anywhere, so remove it.
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though TC2QOS mapping is for switch egress queues, we need to
configure it correclty in order for the Broadcom tag ingress (CPU ->
switch) queue selection to work correctly since there is a 1:1 mapping
between switch egress queues and ingress queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During error injection it was possible to crash in dsa_loop_exit() because of
an attempt to unregister an invalid PHY. We actually want to the driver probing
in dsa_loop_init() even though fixed_phy_register() may return an error to
exercise how DSA deals with such cases, but we should not be crashing during
driver removal.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM7278 has only 128 entries while BCM7445 has the full 256 entries set,
fix that.
Fixes: 7318166cac ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Starfigther 2 driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make this const as it is only used in a copy operation.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these structures const as they are only stored in the ops field of
a dsa_switch structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
Save 2628 bytes on arm eabi by allocate only the required 3 ports.
Now that ds->num_ports is correct: In net/dsa/tag_lan9303.c
eliminate duplicate LAN9303_MAX_PORTS, use ds->num_ports.
(Matching the pattern of other net/dsa/tag_xxx.c files.)
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manually adjust the port settings of user ports once PHY polling has
completed. This patch extends the adjust_link callback to configure the
per port PMCR register, applying the proper values polled from the PHY.
Without this patch flow control was not always getting setup properly.
Signed-off-by: Shashidhar Lakkavalli <shashidhar.lakkavalli@openmesh.com>
Signed-off-by: Muciri Gatimu <muciri@openmesh.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before removing support for MDB dump from
DSA core. The MDBs are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is done as a preparation before removing support for vlan dump from
DSA core. The vlans are synced with the bridge and thus there is no
need for special dump operation support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support FDB add/del to be on a notifier chain the slave
API need to be changed to be switchdev independent.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In lan9303_get_ethtool_stats: Get rid of 0x400 constant magic
by using new lan9303_read_switch_reg() inside loop.
Reduced scope of two variables.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lan9303_enable_packet_processing, lan9303_disable_packet_processing
functions operate on port, so the names should reflect that.
And to align with lan9303_disable_processing(), rename:
lan9303_enable_packet_processing -> lan9303_enable_processing_port
lan9303_disable_packet_processing -> lan9303_disable_processing_port
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify usage of lan9303_enable_packet_processing,
lan9303_disable_packet_processing()
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Will be used instead of '3' in upcomming patches.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_enable_packet_processing, lan9303_disable_packet_processing()
Pass port number (0,1,2) as parameter instead of port offset.
Because other functions in the module pass port numbers.
And to enable simplifications in following patch.
Introduce lan9303_write_switch_port().
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a while now since ds->dst is not an array anymore, but a
simple pointer to a dsa_switch_tree.
Fortunately, SF2 does not support multi-chip and thus ds->index is
always 0.
This patch substitutes 'ds->dst[ds->index].' with 'ds->dst->'.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the PHY EEE settings, rename the .set_eee and
.get_eee ops to respectively .set_mac_eee and .get_mac_eee.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's EEE settings are already accessed by the DSA layer through the
Marvell PHY driver and there is nothing to be done for switch's MACs.
Remove all EEE support from the mv88e6xxx driver and simply return 0
from the EEE ops.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch operations for EEE are only meant to configure a port's
MAC EEE settings. The port's PHY EEE settings are accessed by the DSA
layer and must be made available via a proper PHY driver.
In order to reduce this confusion, remove the phy_device argument from
the .set_eee operation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA drivers are calling phy_init_eee if eee_enabled is true.
Move up this statement in the DSA layer to simplify the DSA drivers.
qca8k does not require to cache the ethtool_eee structures from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is safer to init the EEE before the DSA layer call
phy_ethtool_set_eee, as sf2 and qca8k are doing.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SF2 driver is masking the supported bitfield of its private copy of
the ports' ethtool_eee structures. It is used nowhere, thus remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_get_eee is already called by the DSA layer, thus remove the
duplicated call in the qca8k driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8k driver is currently caching a bitfield of the supported member
of a ethtool_eee private structure, which is unused.
Only the eee_enabled field of the private ethtool_eee copy is updated,
thus using p->advertised and p->lp_advertised is also erroneous.
Remove the usage of these private ethtool_eee members and only rely on
phy_ethtool_get_eee to assign the eee_active member.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If EEE is queried enabled, qca8k_set_eee calls qca8k_eee_enable_set
twice (because it is already called in qca8k_eee_init). Fix that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8k obviously copied code from the sf2 driver as how to set EEE:
if (e->eee_enabled) {
p->eee_enabled = qca8k_eee_init(ds, port, phydev);
if (!p->eee_enabled)
ret = -EOPNOTSUPP;
}
But it did not use the same logic for the EEE init routine, which is
"Returns 0 if EEE was not enabled, or 1 otherwise". This results in
returning -EOPNOTSUPP on success and caching EEE enabled on failure.
This patch fixes the returned value of qca8k_eee_init.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect access (PMI) to phy register only work in I2C mode. In
MDIO mode phy registers must be accessed directly. Introduced
struct lan9303_phy_ops to handle the two modes.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing for the following fix of MDIO phy access:
Renamed functions that access PHY 1 and 2 indirectly through PMI
registers.
lan9303_port_phy_reg_wait_for_completion() to
lan9303_indirect_phy_wait_for_completion()
lan9303_port_phy_reg_read() to
lan9303_indirect_phy_read()
lan9303_port_phy_reg_write() to
lan9303_indirect_phy_write()
Also changed "val" parameter of lan9303_indirect_phy_write() to u16,
for clarity.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_mdio_write()/_read() must multiply register number by 4 to get
offset.
Added some commments to the register definitions.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle that MDIO read with no response return 0xffff.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM53125 entry was missing an arl_entries member which would
basically prevent the ARL search from terminating properly. This switch
has 4 ARL entries, so add that.
Fixes: 1da6df85c6 ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f39908d3b1 ('net: dsa: mv88e6xxx: Set the CMODE for mv88e6390
ports 9 & 10') added support for setting the CMODE for the 6390X family,
but only enabled it for 9290 and 6390 - and left out 6390X.
Fix support for setting the CMODE on 6390X also by assigning
mv88e6390x_port_set_cmode() to the .port_set_cmode function pointer in
mv88e6390x_ops too.
Fixes: f39908d3b1 ("net: dsa: mv88e6xxx: Set the CMODE for mv88e6390 ports 9 & 10")
Signed-off-by: Martin Hundebøll <mnhu@prevas.dk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of relying on a bitmap flag, add a new multi_chip info flag to
describe the presence of the indirect SMI access though the two device
registers 0x0 and 0x1.
All remaining capabilities and flags are now unused. Remove the
mv88e6xxx_cap enum and the info flags bitmaps.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6352 family supports Energy Detect and has one bit for Sense and
one bit for periodically transmit NLP (Energy Detect+TM). The 88E6390
family adds another bit to distinguish Auto or SW wake-up. Chips
supporting EEE all have an EEE Enabled bit in the Port Status Register.
This patch adds new ops for the PHY Energy Detect accesses.
This also allows us to get rid of the MV88E6XXX_FLAG_EEE flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to global1_addr, add a global2_addr member in the info
structure to describe the presence of the Global 2 Registers.
This allows us to get rid of the MV88E6XXX_FLAG_GLOBAL2 flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a pot_clear operation to clear the Priority Override Table and wrap
its call into a mv88e6xxx_pot_setup helper.
This allows us to get rid of the MV88E6XXX_FLAG_G2_POT flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6390 family clear the Priority Override Table the same way as
88E6352, thus add MV88E6XXX_FLAG_G2_POT to MV88E6XXX_FLAGS_FAMILY_6390.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6185 family only has one 16-bit register to mark the 16 802.1D
reserved multicast addresses in the range of 01:80:C2:00:00:0x as MGMT.
The 88E6352 family also has one 16-bit register to mark the 16 GARP
reserved multicast addresses in the range of 01:80:C2:00:00:2x as MGMT.
Split the existing mv88e6095 prefixed mgmt_rsvd2cpu operation into two
distinct mv88e6185 and mv88e6352 prefixed operations, and wrap its call
into a mv88e6xxx_rsvd2cpu_setup helper.
This allows us to also get rid of the MV88E6XXX_CAP_G2_MGMT_EN_* flags.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to g1_irqs, add a g2_irqs member to the info structure to
indicates the presence of the Global 2 Interrupt Source and Mask
registers.
At the same time, provide helpers and document the registers since they
differ a bit between 88E6352 and 88E6390 families.
This allows us to get rid of the MV88E6XXX_FLAG_G2_INT flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 88E6185 family has no Global 2 Interrupt Source or Mask registers.
Remove the MV88E6XXX_FLAG_G2_INT from MV88E6XXX_FLAGS_FAMILY_6185.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the forgotten capabilities and related flags from previous
cleanups.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
MV88E6XXX_FAMILY_6321 is undefined, 88E6321's family is 88E6320,
fix this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't support LED control yet, remove its register definition.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy.c does not need to include the DSA public header. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're accidentally returning the wrong variable. "cmode" is
uninitialized at this point so it causes a static checker warning.
Fixes: 6335e9f244 ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY library now supports an "internal" phy-mode, thus making our
custom parsing code now unnecessary.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Kill the remaining shift macro in favor of calculating at compile time
its value from the more descriptive mask, which gives us a better
representation of the register layout.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the remaining Global 2 registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6352 family has a Global 2 register dedicated to the
watchdog setup. But the 88E6390 turned it into an indirect table.
Prefix and document that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Switch MAC registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 EEPROM registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Cross-chip Port VLAN registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 MGMT registers macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Device Mapping macros.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global 2 Trunk registers macros. At the same
time, fix the hask -> hash typo and use the mv88e6xxx_port_mask helper.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips with an SMI PHY access in Global 2 registers handle both
Clause 22 and Clause 45 of IEEE 802.3.
The 88E6390 family has addition bits to target the internal or external
PHYs connected to the device, and a Setup function in addition to the
default (register) Access function.
Prefix the SMI PHY Command and Data registers macros, implement clear
helpers for Clause 22 and 44 Access functions, rename variable to match
the SMI and switch vocabulary (device and register addresses for Clause
22 and port and device class for Clause 45.)
Finally do not use complex macros but simple 16-bit mask to document the
registers organization.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Marvell chips have an Ingress Rate Limit unit. But the command
values slightly differs between models: 88E6352 use 3-bit for operations
while 88E6390 use different 2-bit operations.
This commit kills the IRL flags in favor of a new operation implementing
the "Init all resources to the initial state" operation.
This fixes the operation of 88E6390 family where 0x1000 means Read the
selected resource 0, register 0 on port 16, instead of init all.
A mv88e6xxx_irl_setup helper is added to wrap the operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a DSA driver implements ethtool statistics, we also override the
master network device's ethtool statistics with the CPU port's
statistics and this has proven to be a possible source of bugs in the
past. Enhance the dsa_loop.c driver to provide statistics under the
forme of ok/error reads and writes from the per-port PHY read/writes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a simple function that only gets used in the driver's remove
function, inline it there.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the remaining Global IP and IEEE Priority and Core
Tag Type registers and give them a clear 16-bit register representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Stats Operation and Counter registers and
give them a clear 16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Monitor Control Register macros
(which became the Global Monitor & MGMT Control Register with 88E6390)
and give a clear 16-bit registers representation.
Use __bf_shf to get the shift value at compile time instead of adding
new defined macros for it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Control and Control 2 registers macros
and give a clear 16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global VTU registers macros and give a clear
16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global ATU Registers macros and give clear
16-bit registers representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Switch MAC Address Register macros and
give clear 16-bit register representation.
At the same time, move mv88e6xxx_g1_set_switch_mac in global1.c, where
it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix and document the Global Status Register macros and give clear
16-bit register representation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for supporting multiple CPU ports, remove
dst->master_netdev and ds->master_netdev and replace them with only one
instance of the common object we have for a port: struct
dsa_port::netdev. ds->master_netdev is currently write only and would be
helpful in the case where we have two switches, both with CPU ports, and
also connected within each other, which the multi-CPU port patch series
would address.
While at it, introduce a helper function used in net/dsa/slave.c to
immediately get a reference on the master network device called
dsa_master_netdev().
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the remaining common Port
Registers macros with MV88E6XXX_PORT.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port IEEE
Priority Remapping registers macros with MV88E6095_PORT_IEEE_PRIO.
The 88E6390 family turned the 0x18 register into a single indirect
table, document that at the same time.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Also fix the following checkpatch checks with a temporary variable:
CHECK: Alignment should match open parenthesis
#65: FILE: drivers/net/dsa/mv88e6xxx/port.c:932:
+ err = mv88e6xxx_port_ieeepmt_write(chip, port,
+ MV88E6390_PORT_IEEE_PRIO_MAP_TABLE_INGRESS_PCP,
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Association
Vector Register macros with MV88E6XXX_PORT_ASSOC_VECTOR.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Egress Rate
Control and Port Egress Rate Control 2 registers macros with
MV88E6XXX_PORT_EGRESS_RATE_CTL1 and MV88E6XXX_PORT_EGRESS_RATE_CTL2.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Control 2
Register macros with MV88E6XXX_PORT_CTL2 and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6095_PORT_CTL2_CPU_PORT_MASK.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Default
VLAN Register macros with MV88E6XXX_PORT_DEFAULT_VLAN.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Based VLAN
Register macros with MV88E6XXX_PORT_BASE_VLAN.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Control 1
Register macros with MV88E6XXX_PORT_CTL1.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Control
Register macros with MV88E6XXX_PORT_CTL0 and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6185_PORT_CTL0_USE_TAG.)
The reason for CTL0 is to make it clear between the badly named
"Port Control", "Port Control 1" and "Port Control 2" registers.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Switch ID
Register macros with MV88E6XXX_PORT_SWITCH_ID.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers, this means shifting their values by 4.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Jamming
Control Register macros with MV88E6XXX_PORT_JAM_CTL and the ones which
differ between implementations with a chosen reference model
(e.g. MV88E6097_PORT_JAM_CTL.)
The 88E6390 family renamed the register to Flow Control and turned it
into an indirect table. Document that as well.
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common MAC Control
Register macros with MV88E6XXX_PORT_MAC_CTL and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6065_PORT_MAC_CTL_SPEED_200.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For implicit namespacing and clarity, prefix the common Port Status
Register macros with MV88E6XXX_PORT_STS and the ones which differ
between implementations with a chosen reference model
(e.g. MV88E6352_PORT_STS_EEE.)
Document the register and prefer ordered hex masks values for all
Marvell 16-bit registers.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefix the PHY_* macros with a Marvell specific MV88E6XXX_ prefix.
There is no functional changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marvell chips have a Jumbo Mode to set the maximum frame size (MTU).
The mv88e6xxx_ops structure is meant to contain generic functionalities,
no driver logic. Change port_jumbo_config to port_set_jumbo_size setting
the mode from a given maximum size value.
There is no functional changes since we still use 10240 bytes.
At the same time, correctly clear all Jumbo Mode bits before writing.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All Marvell chips supporting Pause frames limiting use 1-byte value for
input and output.
Old chips have both bytes adjacent in a 16-bit register. New ones have
an indirect table using 8-bit data.
The mv88e6xxx library functions (such as in port.c) must not contain
driver logic, but only generic helpers. This patch changes the
port_pause_config operation for port_pause_limit taking two u8 arguments
for input and output limits. There is no functional changes.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx_ops describe functionalities, regardless their locations
(which can be Global1, Global2, or whatever register set.)
Rename the g1_set_cpu_port and g1_set_egress_port ops to set_cpu_port
and set_egress_port. No functional changes.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the BR_STATE_* values to abstract a port STP state value.
This provides shorter names and better control over the DSA switch
operation call.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As for the frame mode, add a mv88e6xxx_egress_mode enumeration instead
of a 16-bit register mask.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv888e6xxx driver accesses a port's netdev mostly for printing.
This is bad for 2 reasons: DSA and CPU ports do not have a netdev
pointer; it doesn't give us a correct picture of why a DSA driver might
need to access a port's netdev.
Instead simply use dev_* printing functions with chip->dev (or ds->dev
depending on the scope, both guaranteed to exist), with a p%d prefix for
the target port.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx driver currently tries to be smart and remove by itself a
VLAN entry from the VTU when the driven switch sees no user ports as
members of the VLAN.
This is bad in a multi-chip switch fabric, since a chip in between
others may have no bridge port members, but still needs to be aware of
the VID in order to correctly pass frames in the data path.
Now that the DSA core explicitly manages DSA and CPU ports, do not skip
them when checking remaining VLAN members.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA core adds the CPU and DSA ports itself to the new VLAN
entry, there is no need to include them as members of this VLAN when
initializing a new VTU entry.
As of now, initialize a new VTU entry with all ports excluded.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the target port membership of the VLAN entry in
mv88e6xxx_port_vlan_add where ds is scoped.
Allow the DSA core to call later the port_vlan_add operation for CPU or
DSA ports, by using the Unmodified membership for these ports, as in the
current behavior.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 and mv88e6123 are capable of using EDSA tags when
passing frames from the host to the switch and back.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register bits used for the frame mode were masked with DSA (0x1)
instead of the mask value (0x3) in the 6085 implementation of
port_set_frame_mode. Fix this.
Fixes: 56995cbc35 ("net: dsa: mv88e6xxx: Refactor CPU and DSA port setup")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6161 was using the wrong method to perform statistics
snapshot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to the internal PHYs of the 6161 and 6123 go through global 2
SMI registers. Fix the ops structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the GLOBAL2_* macros where they belong, in the related global2.h
header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the GLOBAL_* macros where they belong, in the related global1.h
header. Include it in global2.c which uses GLOBAL_STATUS_IRQ_DEVICE.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PORT_* macros where they belong, in the related port.h header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the PHY_* macros where they belong, in the related phy.h header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6xxx.h is meant to contains the chip structures and data.
Rename it to chip.h, as for other source/header pairs of the driver.
At the same time, ensure that relative header inclusions are separated
by a newline and sorted alphabetically.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 is a fully integrated layer 2, managed, 7 ports GigE switch
with numerous advanced features. 5 ports incorporate 10/100/1000 Mbps PHYs.
The other 2 ports have interfaces that can be configured as SGMII, RGMII, MII
or RMII. Either of these may connect directly to a host processor or
to an external PHY. The SGMII port may interface to a fiber optic transceiver.
This driver currently supports vlan, fdb, mdb & mirror dsa switch operations.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.
Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.
This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Respect the implicit naming convention used in all register sets
specific files, by renaming the mv88e6xxx_ppu_* functions with the
mv88e6xxx_phy_* prefix.
This is simply a s/xxx_ppu/xxx_phy_ppu/ substitution.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it clear that mv88e6xxx_phy_ppu_{read,write} are an implementation
of the .phy_{read,write} operations, by renaming them with the mv88e6185
prefix, since 88E6185 it is the reference switch model supported in an
upstream board (ZII Dev Rev B), which makes use of them.
Distinguish the signatures of implementation specific and generic PHY
functions in the phy.h header.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similarly to the VTU, PVT and ATU setup, provide a mv88e6xxx_phy_setup
helper which wraps mv88e6xxx_ppu_enable, so that no more PPU-related
functions are exposed outside of phy.c.
Thus make mv88e6xxx_ppu_enable static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port net device passed to b53_fdb_copy is not used. Remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'static' was not enough, the helpers must be 'static inline'
net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]
Fixes: c21fbe29f8 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stub functions in header files need to be static, or we can have
multiple definitions errors.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 6335e9f244 ("net: dsa: mv88e6xxx: mv88e6390X SERDES support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
mv88e6xxx_serdes_power returns an error, so no need to print an error
message inside of it. Rather print it in its caller when the error is
ignored, which is in the mv88e6xxx_port_disable void function.
Catch and return its error in the counterpart mv88e6xxx_port_enable.
Fixes: 04aca99382 ("dsa: mv88e6xxx: Enable/Disable SERDES on port enable/disable")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the port enable/disable callbacks, which enable/disable the
SERDES interfaces, if applicable. This should save a bit of
power/heat.
We also need to enable SERDES on CPU and DSA ports, so keep the
existing call to the op, but make it conditional.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390X family has 8 SERDES lanes. These can be used for 2
10Gbps ports, ports 9 or 10. If these ports are used at slower speeds,
the SERDES lanes become available for other ports for 1000Base-X.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we use an op for SERDES operations, we don't need a flag for
it. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mv88e6390 family has a different SERDES implementation. Refactor
the mv88e6352 code into an ops function, so we can later add the
mv88e6390 code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The upcoming SERDES support will need to make use of PHY functions. Move
them out into a file of there own. No code changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cygnus is a small family of SoCs, of which we currently have
devicetree for BCM11360 and BCM58300. The 11360's B53 is mostly the
same as 58xx, just requiring a tiny bit of setup that was previously
missing.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the DSA public header includes switchdev.h, use the provided
switchdev_obj_dump_cb_t typedef for the object dump callback.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DSA drivers and core use switchdev. Include switchdev.h only once, in
the dsa.h public header, so that inclusion in DSA drivers or forward
declarations of switchdev structures in not necessary anymore.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With more drivers being added, it is time to sort the drivers to
impose some order.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A dsa_switch_tree instance holds a dsa_switch pointer and a port index
to identify the switch port to which the CPU is attached.
Now that the DSA layer has a dsa_port structure to hold this data, use
it to point the switch CPU port.
This patch simply substitutes s/dst->cpu_switch/dst->cpu_dp->ds/ and
s/dst->cpu_port/dst->cpu_dp->index/.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add default case to switch in order to avoid any chance of using an
uninitialized variable _low_, in case s->type does not match any of
the listed case values.
Addresses-Coverity-ID: 1398130
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If 'devm_kzalloc' fails, a NULL pointer will be dereferenced.
Return -ENOMEM instead, as done for some other memory allocation just a
few lines above.
Fixes: 98cd1552ea ("net: dsa: Mock-up driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6390 family of chips use only 2 of the 3 VTU Data registers to pack
the MemberTag and PortState VLAN data. This means that they must be
written or read before or after each VTU/STU operations.
Implement this variant to add support for VTU with such chips. These
chips have a 13th bit for the VID thus set their max_vid to 8191.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer chips such as the 88E6390 have a VTU Page bit in the VTU VID
register to specify a 13th bit for the VID. This can be used to support
8K VLANs.
When dumping the whole VTU, all VID bits must be set to one, including
this VTU Page bit. Add support for VID greater than 4095.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code which fetches or initializes a new VTU entry more concise.
This allows us the get rid of the old underscore prefix naming.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have chip operations for VTU accesses, mark all helpers from
global1_vtu.c as static. Only the various implementations of the
GetNext, LoadPurge and Flush operations need to be exposed.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vtu_loadpurge operation to the chip info structure to differ
the various implementations of the VTU accesses.
Now that the STU handling is abstracted behind VTU operations, kill the
obsolete MV88E6XXX_FLAG_STU flag.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new vtu_getnext operation to the chip info structure to differ the
various implementations of the VTU accesses.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code writes both VTU and STU data when loading a VTU entry,
load the corresponding STU entry at the same time.
This allows us to get rid of the STU management in the
_mv88e6xxx_vtu_new helper and thus remove the separate implementations
of STU Load/Purge and STU GetNext, as well as the unused family checks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the code reads both VTU and STU data on VTU GetNext operation,
fetch the STU entry data of a VTU entry at the same time.
The STU data bits are masked with the VTU data bits and they are now all
read at the same time a VTU GetNext operation is issued.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extract the generic portion of code to issue an STU GetNext operation,
which will be used in other implementations.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code to access the VTU Data registers currently only supports the
88E6185 family and alike: 2-bit membership adjacent to 2-bit port state.
Even though the 88E6352 family introduced an indirect table to program
the VLAN Spanning Tree states, the usage of the VTU Data registers
remains the same regardless the VTU or STU operation.
Now that the mv88e6xxx_vtu_entry structure contains both port membership
and states data, factorize the code to access them in global1_vtu.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though every switch model has a different way to access the VTU
Data bits, the base implementation of the VTU GetNext operation remains
the same: wait, write the first VID to iterate from, start the
operation, and read the next VID.
Move this generic implementation into global1_vtu.c and abstract the
handling of the start VID (similarly to the ATU GetNext implementation),
before introducing a new chip operation for specific chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU VID register in the global1_vtu.c file.
At the same time, move mv88e6xxx_g1_vtu_vid_write at the beginning of
_mv88e6xxx_vtu_loadpurge, which adds no functional changes but makes
future patches simpler.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU SID register in the global1_vtu.c file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helpers to access the VTU FID register in the global1_vtu.c file.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the VTU flush operation to global1_vtu.c and call it from a
mv88e6xxx_vtu_setup helper, similarly to the ATU and PVT setup.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the helper functions to access the Global 1 VTU Operation register
to a new global1_vtu.c file, and get rid of the old underscore prefix
naming convention. This file will be extended will all VTU/STU related
code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN aware Marvell chips can program 802.1Q VLAN membership as well as
802.1s per VLAN Spanning Tree state using the same 3 VTU Data registers.
Some chips such as 88E6185 use different Data registers offsets for
ports state and membership, and program them in a single operation.
Other chips such as 88E6352 use the same register layout but program
them in distinct operations (an indirect table is used for 802.1s.)
Newer chips such as 88E6390 use the same offsets for both state and
membership in distinct operations, thus require multiple data accesses.
To correctly abstract this, split the "data" structure member of
mv88e6xxx_vtu_entry in two "state" and "member" members, before adding
VTU support for newer chips.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chips don't have a VLAN Table Unit, most of them do have a 4K
table, some others as the 88E6390 family has a 13th bit for the VID.
Add a new max_vid member to the info structure, used to check the
presence of a VTU as well as the value used to iterate from in VTU
GetNext operations.
This makes the MV88E6XXX_FLAG_VTU obsolete, thus remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 58xx devices (Northstar Plus) do actually have their CPU port wired
at port 8, it was unfortunately set to port 5 (B53_CPU_PORT_25) which is
incorrect, since that is the second possible management port.
Fixes: 991a36bb46 ("net: dsa: b53: Add support for BCM585xx/586xx/88312 integrated switch")
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Phil Reid