Pull irq updates from Thomas Gleixner:
"This updated pull request does not contain the last few GIC related
patches which were reported to cause a regression. There is a fix
available, but I let it breed for a couple of days first.
The irq departement provides:
- new infrastructure to support non PCI based MSI interrupts
- a couple of new irq chip drivers
- the usual pile of fixlets and updates to irq chip drivers
- preparatory changes for removal of the irq argument from interrupt
flow handlers
- preparatory changes to remove IRQF_VALID"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (129 commits)
irqchip/imx-gpcv2: IMX GPCv2 driver for wakeup sources
irqchip: Add bcm2836 interrupt controller for Raspberry Pi 2
irqchip: Add documentation for the bcm2836 interrupt controller
irqchip/bcm2835: Add support for being used as a second level controller
irqchip/bcm2835: Refactor handle_IRQ() calls out of MAKE_HWIRQ
PCI: xilinx: Fix typo in function name
irqchip/gic: Ensure gic_cpu_if_up/down() programs correct GIC instance
irqchip/gic: Only allow the primary GIC to set the CPU map
PCI/MSI: pci-xgene-msi: Consolidate chained IRQ handler install/remove
unicore32/irq: Prepare puv3_gpio_handler for irq argument removal
tile/pci_gx: Prepare trio_handle_level_irq for irq argument removal
m68k/irq: Prepare irq handlers for irq argument removal
C6X/megamode-pic: Prepare megamod_irq_cascade for irq argument removal
blackfin: Prepare irq handlers for irq argument removal
arc/irq: Prepare idu_cascade_isr for irq argument removal
sparc/irq: Use access helper irq_data_get_affinity_mask()
sparc/irq: Use helper irq_data_get_irq_handler_data()
parisc/irq: Use access helper irq_data_get_affinity_mask()
mn10300/irq: Use access helper irq_data_get_affinity_mask()
irqchip/i8259: Prepare i8259_irq_dispatch for irq argument removal
...
While pmem is usable as a block device or via DAX mappings to userspace
there are several usage scenarios that can not target pmem due to its
lack of struct page coverage. In preparation for "hot plugging" pmem
into the vmemmap add ZONE_DEVICE as a new zone to tag these pages
separately from the ones that are subject to standard page allocations.
Importantly "device memory" can be removed at will by userspace
unbinding the driver of the device.
Having a separate zone prevents allocation and otherwise marks these
pages that are distinct from typical uniform memory. Device memory has
different lifetime and performance characteristics than RAM. However,
since we have run out of ZONES_SHIFT bits this functionality currently
depends on sacrificing ZONE_DMA.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Jerome Glisse <j.glisse@gmail.com>
[hch: various simplifications in the arch interface]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Existing users of ioremap_cache() are mapping memory that is known in
advance to not have i/o side effects. These users are forced to cast
away the __iomem annotation, or otherwise neglect to fix the sparse
errors thrown when dereferencing pointers to this memory. Provide
memremap() as a non __iomem annotated ioremap_*() in the case when
ioremap is otherwise a pointer to cacheable memory. Empirically,
ioremap_<cacheable-type>() call sites are seeking memory-like semantics
(e.g. speculative reads, and prefetching permitted).
memremap() is a break from the ioremap implementation pattern of adding
a new memremap_<type>() for each mapping type and having silent
compatibility fall backs. Instead, the implementation defines flags
that are passed to the central memremap() and if a mapping type is not
supported by an arch memremap returns NULL.
We introduce a memremap prototype as a trivial wrapper of
ioremap_cache() and ioremap_wt(). Later, once all ioremap_cache() and
ioremap_wt() usage has been removed from drivers we teach archs to
implement arch_memremap() with the ability to strictly enforce the
mapping type.
Cc: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Preparation for uniform definition of ioremap, ioremap_wc, ioremap_wt,
and ioremap_cache, tree-wide.
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This fixes a typo in two error messages, from "Reigster" to
"Register".
Signed-off-by: Nik Nyby <nikolas@gnu.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Replace ACCESS_ONCE() macro in smp_store_release() and smp_load_acquire()
with WRITE_ONCE() and READ_ONCE() on x86, arm, arm64, ia64, metag, mips,
powerpc, s390, sparc and asm-generic since ACCESS_ONCE() does not work
reliably on non-scalar types.
WRITE_ONCE() and READ_ONCE() were introduced in the following commits:
230fa253df ("kernel: Provide READ_ONCE and ASSIGN_ONCE")
43239cbe79 ("kernel: Change ASSIGN_ONCE(val, x) to WRITE_ONCE(x, val)")
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Davidlohr Bueso <dbueso@suse.de>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Alexander Duyck <alexander.h.duyck@redhat.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1438528264-714-1-git-send-email-andreyknvl@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implement atomic logic ops -- atomic_{or,xor,and}.
These will replace the atomic_{set,clear}_mask functions that are
available on some archs.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__irq_set_chip_handler_name_locked() is about to be replaced. Use
irq_set_chip_handler_name_locked() instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/20150713131034.723024979@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is a preparatory patch for moving irq_data struct members.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/20150713131034.630273860@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When we scan a PCI bus, we read PCI-PCI bridge window registers with
pci_read_bridge_bases() so we can validate the resource hierarchy. Most
architectures call pci_read_bridge_bases() from pcibios_fixup_bus(), but
PCI-PCI bridges are not arch-specific, so this doesn't need to be in
arch-specific code.
Call pci_read_bridge_bases() directly from the PCI core instead of from
arch code.
For alpha and mips, we now call pci_read_bridge_bases() always; previously
we only called it if PCI_PROBE_ONLY was set.
[bhelgaas: changelog]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: James E.J. Bottomley <jejb@parisc-linux.org>
CC: Michael Ellerman <mpe@ellerman.id.au>
CC: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: David Howells <dhowells@redhat.com>
CC: Russell King <linux@arm.linux.org.uk>
CC: Tony Luck <tony.luck@intel.com>
CC: David S. Miller <davem@davemloft.net>
CC: Ingo Molnar <mingo@redhat.com>
CC: Guenter Roeck <linux@roeck-us.net>
CC: Michal Simek <monstr@monstr.eu>
CC: Chris Zankel <chris@zankel.net>
Commit 2ae416b142 ("mm: new mm hook framework") introduced an empty
header file (mm-arch-hooks.h) for every architecture, even those which
doesn't need to define mm hooks.
As suggested by Geert Uytterhoeven, this could be cleaned through the use
of a generic header file included via each per architecture
asm/include/Kbuild file.
The PowerPC architecture is not impacted here since this architecture has
to defined the arch_remap MM hook.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use irq_data access helper to access irq_data->msi_desc, so we can
move msi_desc from struct irq_data into struct irq_common_data later.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added the x86 implementation of word-at-a-time to the
generic version, which previously only supported big-endian.
Omitted the x86-specific load_unaligned_zeropad(), which in
any case is also not present for the existing BE-only
implementation of a word-at-a-time, and is only used under
CONFIG_DCACHE_WORD_ACCESS.
Added as a "generic-y" to the Kbuilds of all architectures
that didn't previously have it.
Signed-off-by: Chris Metcalf <cmetcalf@ezchip.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Soa6
-----END PGP SIGNATURE-----
Merge tag 'please-pull-put_kernel_page' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 boot noise reduction fix from Tony Luck:
"Remove some boot noise from a now-invalid check that pages are
reserved"
* tag 'please-pull-put_kernel_page' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Drop debug test/printk that some special pages are marked reserved
In commit 92923ca3aa "mm: meminit: only set page reserved in the memblock region"
we dropped setting the reserved bits for all pages. This results in some warnings
on ia64:
put_kernel_page: page at 0xe000000005588000 not in reserved memory
put_kernel_page: page at 0xe000000005588000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
put_kernel_page: page at 0xe000000005580000 not in reserved memory
the two different pages match up with two objects from the loaded kernel
that get mapped by arch/ia64/mm/init.c:setup_gate()
a000000101588000 D __start_gate_section
a000000101580000 D empty_zero_page
In a discussion with Mel Gorman:
http://lkml.kernel.org/r/20150526102219.GB13750%40suse.de
he suggested that while the preferred approach might be to
set the reserved bit for these pages, it would also be OK
to just drop the test:
"as it's a debugging check that is ia-64 specific"
After hunting around a bit and failin to find a good place to mark these
pages as reserved - I decided to just delete the test.
Signed-off-by: Tony Luck <tony.luck@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0BDx
-----END PGP SIGNATURE-----
Merge tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux
Pull module_init replacement part one from Paul Gortmaker:
"Replace module_init with equivalent device_initcall in non modules.
This series of commits converts non-modular code that is using the
module_init() call to hook itself into the system to instead use
device_initcall().
The conversion is a runtime no-op, since module_init actually becomes
__initcall in the non-modular case, and that in turn gets mapped onto
device_initcall. A couple files show a larger negative diffstat,
representing ones that had a module_exit function that we remove here
vs previously relying on the linker to dispose of it.
We make this conversion now, so that we can relocate module_init from
init.h into module.h in the future.
The files changed here are just limited to those that would otherwise
have to add module.h to obviously non-modular code, in order to avoid
a compile fail, as testing has shown"
* tag 'module_init-device_initcall-v4.1-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux:
MIPS: don't use module_init in non-modular cobalt/mtd.c file
drivers/leds: don't use module_init in non-modular leds-cobalt-raq.c
cris: don't use module_init for non-modular core eeprom.c code
tty/metag_da: Avoid module_init/module_exit in non-modular code
drivers/clk: don't use module_init in clk-nomadik.c which is non-modular
xtensa: don't use module_init for non-modular core network.c code
sh: don't use module_init in non-modular psw.c code
mn10300: don't use module_init in non-modular flash.c code
parisc64: don't use module_init for non-modular core perf code
parisc: don't use module_init for non-modular core pdc_cons code
cris: don't use module_init for non-modular core intmem.c code
ia64: don't use module_init in non-modular sim/simscsi.c code
ia64: don't use module_init for non-modular core kernel/mca.c code
arm: don't use module_init in non-modular mach-vexpress/spc.c code
powerpc: don't use module_init in non-modular 83xx suspend code
powerpc: use device_initcall for registering rtc devices
x86: don't use module_init in non-modular devicetree.c code
x86: don't use module_init in non-modular intel_mid_vrtc.c
__early_pfn_to_nid() use static variables to cache recent lookups as
memblock lookups are very expensive but it assumes that memory
initialisation is single-threaded. Parallel initialisation of struct
pages will break that assumption so this patch makes __early_pfn_to_nid()
SMP-safe by requiring the caller to cache recent search information.
early_pfn_to_nid() keeps the same interface but is only safe to use early
in boot due to the use of a global static variable. meminit_pfn_in_nid()
is an SMP-safe version that callers must maintain their own state for.
Signed-off-by: Mel Gorman <mgorman@suse.de>
Tested-by: Nate Zimmer <nzimmer@sgi.com>
Tested-by: Waiman Long <waiman.long@hp.com>
Tested-by: Daniel J Blueman <daniel@numascale.com>
Acked-by: Pekka Enberg <penberg@kernel.org>
Cc: Robin Holt <robinmholt@gmail.com>
Cc: Nate Zimmer <nzimmer@sgi.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Waiman Long <waiman.long@hp.com>
Cc: Scott Norton <scott.norton@hp.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory devices
(NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware Interface
table). After registering NVDIMMs the NFIT driver then registers
"region" devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block device
(disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of persistent
memory address ranges is re-worked to drive PMEM-namespaces emitted by
the libnvdimm-core. In this update the PMEM driver, on x86, gains the
ability to assert that writes to persistent memory have been flushed all
the way through the caches and buffers in the platform to persistent
media. See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through "Block
Data Windows" as defined by the NFIT. The primary difference of this
driver to PMEM is that only a small window of persistent memory is
mapped into system address space at any given point in time. Per-NVDIMM
windows are reprogrammed at run time, per-I/O, to access different
portions of the media. BLK-mode, by definition, does not support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss). The
sinister aspect of sector tearing is that most applications do not know
they have a atomic sector dependency. At least today's disk's rarely
ever tear sectors and if they do one almost certainly gets a CRC error
on access. NVDIMMs will always tear and always silently. Until an
application is audited to be robust in the presence of sector-tearing
the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VtWG
-----END PGP SIGNATURE-----
Merge tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm
Pull libnvdimm subsystem from Dan Williams:
"The libnvdimm sub-system introduces, in addition to the
libnvdimm-core, 4 drivers / enabling modules:
NFIT:
Instantiates an "nvdimm bus" with the core and registers memory
devices (NVDIMMs) enumerated by the ACPI 6.0 NFIT (NVDIMM Firmware
Interface table).
After registering NVDIMMs the NFIT driver then registers "region"
devices. A libnvdimm-region defines an access mode and the
boundaries of persistent memory media. A region may span multiple
NVDIMMs that are interleaved by the hardware memory controller. In
turn, a libnvdimm-region can be carved into a "namespace" device and
bound to the PMEM or BLK driver which will attach a Linux block
device (disk) interface to the memory.
PMEM:
Initially merged in v4.1 this driver for contiguous spans of
persistent memory address ranges is re-worked to drive
PMEM-namespaces emitted by the libnvdimm-core.
In this update the PMEM driver, on x86, gains the ability to assert
that writes to persistent memory have been flushed all the way
through the caches and buffers in the platform to persistent media.
See memcpy_to_pmem() and wmb_pmem().
BLK:
This new driver enables access to persistent memory media through
"Block Data Windows" as defined by the NFIT. The primary difference
of this driver to PMEM is that only a small window of persistent
memory is mapped into system address space at any given point in
time.
Per-NVDIMM windows are reprogrammed at run time, per-I/O, to access
different portions of the media. BLK-mode, by definition, does not
support DAX.
BTT:
This is a library, optionally consumed by either PMEM or BLK, that
converts a byte-accessible namespace into a disk with atomic sector
update semantics (prevents sector tearing on crash or power loss).
The sinister aspect of sector tearing is that most applications do
not know they have a atomic sector dependency. At least today's
disk's rarely ever tear sectors and if they do one almost certainly
gets a CRC error on access. NVDIMMs will always tear and always
silently. Until an application is audited to be robust in the
presence of sector-tearing the usage of BTT is recommended.
Thanks to: Ross Zwisler, Jeff Moyer, Vishal Verma, Christoph Hellwig,
Ingo Molnar, Neil Brown, Boaz Harrosh, Robert Elliott, Matthew Wilcox,
Andy Rudoff, Linda Knippers, Toshi Kani, Nicholas Moulin, Rafael
Wysocki, and Bob Moore"
* tag 'libnvdimm-for-4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/nvdimm: (33 commits)
arch, x86: pmem api for ensuring durability of persistent memory updates
libnvdimm: Add sysfs numa_node to NVDIMM devices
libnvdimm: Set numa_node to NVDIMM devices
acpi: Add acpi_map_pxm_to_online_node()
libnvdimm, nfit: handle unarmed dimms, mark namespaces read-only
pmem: flag pmem block devices as non-rotational
libnvdimm: enable iostat
pmem: make_request cleanups
libnvdimm, pmem: fix up max_hw_sectors
libnvdimm, blk: add support for blk integrity
libnvdimm, btt: add support for blk integrity
fs/block_dev.c: skip rw_page if bdev has integrity
libnvdimm: Non-Volatile Devices
tools/testing/nvdimm: libnvdimm unit test infrastructure
libnvdimm, nfit, nd_blk: driver for BLK-mode access persistent memory
nd_btt: atomic sector updates
libnvdimm: infrastructure for btt devices
libnvdimm: write blk label set
libnvdimm: write pmem label set
libnvdimm: blk labels and namespace instantiation
...
Merge second patchbomb from Andrew Morton:
- most of the rest of MM
- lots of misc things
- procfs updates
- printk feature work
- updates to get_maintainer, MAINTAINERS, checkpatch
- lib/ updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (96 commits)
exit,stats: /* obey this comment */
coredump: add __printf attribute to cn_*printf functions
coredump: use from_kuid/kgid when formatting corename
fs/reiserfs: remove unneeded cast
NILFS2: support NFSv2 export
fs/befs/btree.c: remove unneeded initializations
fs/minix: remove unneeded cast
init/do_mounts.c: add create_dev() failure log
kasan: remove duplicate definition of the macro KASAN_FREE_PAGE
fs/efs: femove unneeded cast
checkpatch: emit "NOTE: <types>" message only once after multiple files
checkpatch: emit an error when there's a diff in a changelog
checkpatch: validate MODULE_LICENSE content
checkpatch: add multi-line handling for PREFER_ETHER_ADDR_COPY
checkpatch: suggest using eth_zero_addr() and eth_broadcast_addr()
checkpatch: fix processing of MEMSET issues
checkpatch: suggest using ether_addr_equal*()
checkpatch: avoid NOT_UNIFIED_DIFF errors on cover-letter.patch files
checkpatch: remove local from codespell path
checkpatch: add --showfile to allow input via pipe to show filenames
...
Nobody used these hooks so they were removed from common code, and can now
be removed from the architectures.
Signed-off-by: Dominik Dingel <dingel@linux.vnet.ibm.com>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull asm/scatterlist.h removal from Jens Axboe:
"We don't have any specific arch scatterlist anymore, since parisc
finally switched over. Kill the include"
* 'for-4.2/sg' of git://git.kernel.dk/linux-block:
remove scatterlist.h generation from arch Kbuild files
remove <asm/scatterlist.h>
Currently we have many duplicates in definitions of
hugetlb_prefault_arch_hook. In all architectures this function is empty.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CRIU is recreating the process memory layout by remapping the checkpointee
memory area on top of the current process (criu). This includes remapping
the vDSO to the place it has at checkpoint time.
However some architectures like powerpc are keeping a reference to the
vDSO base address to build the signal return stack frame by calling the
vDSO sigreturn service. So once the vDSO has been moved, this reference
is no more valid and the signal frame built later are not usable.
This patch serie is introducing a new mm hook framework, and a new
arch_remap hook which is called when mremap is done and the mm lock still
hold. The next patch is adding the vDSO remap and unmap tracking to the
powerpc architecture.
This patch (of 3):
This patch introduces a new set of header file to manage mm hooks:
- per architecture empty header file (arch/x/include/asm/mm-arch-hooks.h)
- a generic header (include/linux/mm-arch-hooks.h)
The architecture which need to overwrite a hook as to redefine it in its
header file, while architecture which doesn't need have nothing to do.
The default hooks are defined in the generic header and are used in the
case the architecture is not defining it.
In a next step, mm hooks defined in include/asm-generic/mm_hooks.h should
be moved here.
Signed-off-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Pavel Emelyanov <xemul@parallels.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have many duplicates in definitions of huge_pmd_unshare. In
all architectures this function just returns 0 when
CONFIG_ARCH_WANT_HUGE_PMD_SHARE is N.
This patch puts the default implementation in mm/hugetlb.c and lets these
architectures use the common code.
Signed-off-by: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: David Rientjes <rientjes@google.com>
Cc: James Yang <James.Yang@freescale.com>
Cc: Aneesh Kumar <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull x86 core updates from Ingo Molnar:
"There were so many changes in the x86/asm, x86/apic and x86/mm topics
in this cycle that the topical separation of -tip broke down somewhat -
so the result is a more traditional architecture pull request,
collected into the 'x86/core' topic.
The topics were still maintained separately as far as possible, so
bisectability and conceptual separation should still be pretty good -
but there were a handful of merge points to avoid excessive
dependencies (and conflicts) that would have been poorly tested in the
end.
The next cycle will hopefully be much more quiet (or at least will
have fewer dependencies).
The main changes in this cycle were:
* x86/apic changes, with related IRQ core changes: (Jiang Liu, Thomas
Gleixner)
- This is the second and most intrusive part of changes to the x86
interrupt handling - full conversion to hierarchical interrupt
domains:
[IOAPIC domain] -----
|
[MSI domain] --------[Remapping domain] ----- [ Vector domain ]
| (optional) |
[HPET MSI domain] ----- |
|
[DMAR domain] -----------------------------
|
[Legacy domain] -----------------------------
This now reflects the actual hardware and allowed us to distangle
the domain specific code from the underlying parent domain, which
can be optional in the case of interrupt remapping. It's a clear
separation of functionality and removes quite some duct tape
constructs which plugged the remap code between ioapic/msi/hpet
and the vector management.
- Intel IOMMU IRQ remapping enhancements, to allow direct interrupt
injection into guests (Feng Wu)
* x86/asm changes:
- Tons of cleanups and small speedups, micro-optimizations. This
is in preparation to move a good chunk of the low level entry
code from assembly to C code (Denys Vlasenko, Andy Lutomirski,
Brian Gerst)
- Moved all system entry related code to a new home under
arch/x86/entry/ (Ingo Molnar)
- Removal of the fragile and ugly CFI dwarf debuginfo annotations.
Conversion to C will reintroduce many of them - but meanwhile
they are only getting in the way, and the upstream kernel does
not rely on them (Ingo Molnar)
- NOP handling refinements. (Borislav Petkov)
* x86/mm changes:
- Big PAT and MTRR rework: making the code more robust and
preparing to phase out exposing direct MTRR interfaces to drivers -
in favor of using PAT driven interfaces (Toshi Kani, Luis R
Rodriguez, Borislav Petkov)
- New ioremap_wt()/set_memory_wt() interfaces to support
Write-Through cached memory mappings. This is especially
important for good performance on NVDIMM hardware (Toshi Kani)
* x86/ras changes:
- Add support for deferred errors on AMD (Aravind Gopalakrishnan)
This is an important RAS feature which adds hardware support for
poisoned data. That means roughly that the hardware marks data
which it has detected as corrupted but wasn't able to correct, as
poisoned data and raises an APIC interrupt to signal that in the
form of a deferred error. It is the OS's responsibility then to
take proper recovery action and thus prolonge system lifetime as
far as possible.
- Add support for Intel "Local MCE"s: upcoming CPUs will support
CPU-local MCE interrupts, as opposed to the traditional system-
wide broadcasted MCE interrupts (Ashok Raj)
- Misc cleanups (Borislav Petkov)
* x86/platform changes:
- Intel Atom SoC updates
... and lots of other cleanups, fixlets and other changes - see the
shortlog and the Git log for details"
* 'x86-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (222 commits)
x86/hpet: Use proper hpet device number for MSI allocation
x86/hpet: Check for irq==0 when allocating hpet MSI interrupts
x86/mm/pat, drivers/infiniband/ipath: Use arch_phys_wc_add() and require PAT disabled
x86/mm/pat, drivers/media/ivtv: Use arch_phys_wc_add() and require PAT disabled
x86/platform/intel/baytrail: Add comments about why we disabled HPET on Baytrail
genirq: Prevent crash in irq_move_irq()
genirq: Enhance irq_data_to_desc() to support hierarchy irqdomain
iommu, x86: Properly handle posted interrupts for IOMMU hotplug
iommu, x86: Provide irq_remapping_cap() interface
iommu, x86: Setup Posted-Interrupts capability for Intel iommu
iommu, x86: Add cap_pi_support() to detect VT-d PI capability
iommu, x86: Avoid migrating VT-d posted interrupts
iommu, x86: Save the mode (posted or remapped) of an IRTE
iommu, x86: Implement irq_set_vcpu_affinity for intel_ir_chip
iommu: dmar: Provide helper to copy shared irte fields
iommu: dmar: Extend struct irte for VT-d Posted-Interrupts
iommu: Add new member capability to struct irq_remap_ops
x86/asm/entry/64: Disentangle error_entry/exit gsbase/ebx/usermode code
x86/asm/entry/32: Shorten __audit_syscall_entry() args preparation
x86/asm/entry/32: Explain reloading of registers after __audit_syscall_entry()
...
Pull scheduler updates from Ingo Molnar:
"The main changes are:
- lockless wakeup support for futexes and IPC message queues
(Davidlohr Bueso, Peter Zijlstra)
- Replace spinlocks with atomics in thread_group_cputimer(), to
improve scalability (Jason Low)
- NUMA balancing improvements (Rik van Riel)
- SCHED_DEADLINE improvements (Wanpeng Li)
- clean up and reorganize preemption helpers (Frederic Weisbecker)
- decouple page fault disabling machinery from the preemption
counter, to improve debuggability and robustness (David
Hildenbrand)
- SCHED_DEADLINE documentation updates (Luca Abeni)
- topology CPU masks cleanups (Bartosz Golaszewski)
- /proc/sched_debug improvements (Srikar Dronamraju)"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (79 commits)
sched/deadline: Remove needless parameter in dl_runtime_exceeded()
sched: Remove superfluous resetting of the p->dl_throttled flag
sched/deadline: Drop duplicate init_sched_dl_class() declaration
sched/deadline: Reduce rq lock contention by eliminating locking of non-feasible target
sched/deadline: Make init_sched_dl_class() __init
sched/deadline: Optimize pull_dl_task()
sched/preempt: Add static_key() to preempt_notifiers
sched/preempt: Fix preempt notifiers documentation about hlist_del() within unsafe iteration
sched/stop_machine: Fix deadlock between multiple stop_two_cpus()
sched/debug: Add sum_sleep_runtime to /proc/<pid>/sched
sched/debug: Replace vruntime with wait_sum in /proc/sched_debug
sched/debug: Properly format runnable tasks in /proc/sched_debug
sched/numa: Only consider less busy nodes as numa balancing destinations
Revert 095bebf61a ("sched/numa: Do not move past the balance point if unbalanced")
sched/fair: Prevent throttling in early pick_next_task_fair()
preempt: Reorganize the notrace definitions a bit
preempt: Use preempt_schedule_context() as the official tracing preemption point
sched: Make preempt_schedule_context() function-tracing safe
x86: Remove cpu_sibling_mask() and cpu_core_mask()
x86: Replace cpu_**_mask() with topology_**_cpumask()
...
Pull locking updates from Ingo Molnar:
"The main changes are:
- 'qspinlock' support, enabled on x86: queued spinlocks - these are
now the spinlock variant used by x86 as they outperform ticket
spinlocks in every category. (Waiman Long)
- 'pvqspinlock' support on x86: paravirtualized variant of queued
spinlocks. (Waiman Long, Peter Zijlstra)
- 'qrwlock' support, enabled on x86: queued rwlocks. Similar to
queued spinlocks, they are now the variant used by x86:
CONFIG_ARCH_USE_QUEUED_SPINLOCKS=y
CONFIG_QUEUED_SPINLOCKS=y
CONFIG_ARCH_USE_QUEUED_RWLOCKS=y
CONFIG_QUEUED_RWLOCKS=y
- various lockdep fixlets
- various locking primitives cleanups, further WRITE_ONCE()
propagation"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
locking/lockdep: Remove hard coded array size dependency
locking/qrwlock: Don't contend with readers when setting _QW_WAITING
lockdep: Do not break user-visible string
locking/arch: Rename set_mb() to smp_store_mb()
locking/arch: Add WRITE_ONCE() to set_mb()
rtmutex: Warn if trylock is called from hard/softirq context
arch: Remove __ARCH_HAVE_CMPXCHG
locking/rtmutex: Drop usage of __HAVE_ARCH_CMPXCHG
locking/qrwlock: Rename QUEUE_RWLOCK to QUEUED_RWLOCKS
locking/pvqspinlock: Rename QUEUED_SPINLOCK to QUEUED_SPINLOCKS
locking/pvqspinlock: Replace xchg() by the more descriptive set_mb()
locking/pvqspinlock, x86: Enable PV qspinlock for Xen
locking/pvqspinlock, x86: Enable PV qspinlock for KVM
locking/pvqspinlock, x86: Implement the paravirt qspinlock call patching
locking/pvqspinlock: Implement simple paravirt support for the qspinlock
locking/qspinlock: Revert to test-and-set on hypervisors
locking/qspinlock: Use a simple write to grab the lock
locking/qspinlock: Optimize for smaller NR_CPUS
locking/qspinlock: Extract out code snippets for the next patch
locking/qspinlock: Add pending bit
...
The simscsi.o is built for HP_SIMSCSI -- which is bool, and hence
this code is either present or absent. It will never be modular,
so using module_init as an alias for __initcall can be somewhat
misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Note that direct use of __initcall is discouraged, vs. one
of the priority categorized subgroups. As __initcall gets
mapped onto device_initcall, our use of device_initcall
directly in this change means that the runtime impact is
zero -- it will remain at level 6 in initcall ordering.
And since it can't be modular, we remove all the __exitcall
stuff related to module_exit() -- it is dead code that won't
ever be executed.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The mca.c code is always built in. It will never be modular,
so using module_init as an alias for __initcall is rather
misleading.
Fix this up now, so that we can relocate module_init from
init.h into module.h in the future. If we don't do this, we'd
have to add module.h to obviously non-modular code, and that
would be a worse thing.
Direct use of __initcall is discouraged, vs prioritized ones.
Use of device_initcall is consistent with what __initcall
maps onto, and hence does not change the init order, making the
impact of this change zero. Should someone with real hardware
for boot testing want to change it later to arch_initcall or
something different, they can do that at a later date.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, a;
@@
-init_timer(&e1);
+setup_timer(&e1, a, 0UL);
... when != a = e2
-e1.function = a;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This is needed the following modules:
"Linux Kernel Dump Test Tool Module"
CONFIG_LKDTM drivers/misc/lkdtm.c
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
All the ia64 pvops code is now dead code since both
xen and kvm support have been ripped out [0] [1]. Just
that no one had troubled to rip this stuff out. The only
useful remaining pieces were the old pvops docs but that
was recently also generalized and moved out from ia64 [2].
This has been run time tested on an ia64 Madison system.
[0] 003f7de625 "KVM: ia64: remove" since v3.19-rc1
[1] d52eefb47d "ia64/xen: Remove Xen support for ia64" since v3.14-rc1
[2] "virtual: Documentation: simplify and generalize paravirt_ops.txt"
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
pci_dma_burst_advice() was added by e24c2d963a ("[PATCH] PCI: DMA
bursting advice") but apparently never used. Remove it.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Michal Simek <monstr@monstr.eu> # microblaze
CC: David S. Miller <davem@davemloft.net>
cpumask_test_cpu() doesn't take volatile, unlike the obsoleted
cpu_isset. The only place ia64 really cares is the spin waiting for a
bit; udelay() is probably a barrier but insert barrier() to be sure.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
ACPI 6.0 formalizes e820-type-7 and efi-type-14 as persistent memory.
Mark it "reserved" and allow it to be claimed by a persistent memory
device driver.
This definition is in addition to the Linux kernel's existing type-12
definition that was recently added in support of shipping platforms with
NVDIMM support that predate ACPI 6.0 (which now classifies type-12 as
OEM reserved).
Note, /proc/iomem can be consulted for differentiating legacy
"Persistent Memory (legacy)" E820_PRAM vs standard "Persistent Memory"
E820_PMEM.
Cc: Boaz Harrosh <boaz@plexistor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Tested-by: Toshi Kani <toshi.kani@hp.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Commit 97badf873a (device property: Make it possible to use
secondary firmware nodes) uncovered a bug in the x86 (and ia64) PCI
host bridge initialization code that assumes bridge->bus->sysdata
to always point to a struct pci_sysdata object which need not be
the case (in particular, the Xen PCI frontend driver sets it to point
to a different data type). If it is not the case, an incorrect
pointer (or a piece of data that is not a pointer at all) will be
passed to ACPI_COMPANION_SET() and that may cause interesting
breakage to happen going forward.
To work around this problem use the observation that the ACPI
host bridge initialization always passes NULL as parent to
pci_create_root_bus(), so if pcibios_root_bridge_prepare() sees
a non-NULL parent of the bridge, it should not attempt to set
an ACPI companion for it, because that means that
pci_create_root_bus() has been called by someone else.
Fixes: 97badf873a (device property: Make it possible to use secondary firmware nodes)
Reported-and-tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Introduce faulthandler_disabled() and use it to check for irq context and
disabled pagefaults (via pagefault_disable()) in the pagefault handlers.
Please note that we keep the in_atomic() checks in place - to detect
whether in irq context (in which case preemption is always properly
disabled).
In contrast, preempt_disable() should never be used to disable pagefaults.
With !CONFIG_PREEMPT_COUNT, preempt_disable() doesn't modify the preempt
counter, and therefore the result of in_atomic() differs.
We validate that condition by using might_fault() checks when calling
might_sleep().
Therefore, add a comment to faulthandler_disabled(), describing why this
is needed.
faulthandler_disabled() and pagefault_disable() are defined in
linux/uaccess.h, so let's properly add that include to all relevant files.
This patch is based on a patch from Thomas Gleixner.
Reviewed-and-tested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: David.Laight@ACULAB.COM
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: airlied@linux.ie
Cc: akpm@linux-foundation.org
Cc: benh@kernel.crashing.org
Cc: bigeasy@linutronix.de
Cc: borntraeger@de.ibm.com
Cc: daniel.vetter@intel.com
Cc: heiko.carstens@de.ibm.com
Cc: herbert@gondor.apana.org.au
Cc: hocko@suse.cz
Cc: hughd@google.com
Cc: mst@redhat.com
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: schwidefsky@de.ibm.com
Cc: yang.shi@windriver.com
Link: http://lkml.kernel.org/r/1431359540-32227-7-git-send-email-dahi@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since set_mb() is really about an smp_mb() -- not a IO/DMA barrier
like mb() rename it to match the recent smp_load_acquire() and
smp_store_release().
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Since we assume set_mb() to result in a single store followed by a
full memory barrier, employ WRITE_ONCE().
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We removed the only user of this define in the rtmutex code. Get rid
of it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
We don't have any arch specific scatterlist now that parisc switched over
to the generic one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull fourth vfs update from Al Viro:
"d_inode() annotations from David Howells (sat in for-next since before
the beginning of merge window) + four assorted fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
RCU pathwalk breakage when running into a symlink overmounting something
fix I_DIO_WAKEUP definition
direct-io: only inc/dec inode->i_dio_count for file systems
fs/9p: fix readdir()
VFS: assorted d_backing_inode() annotations
VFS: fs/inode.c helpers: d_inode() annotations
VFS: fs/cachefiles: d_backing_inode() annotations
VFS: fs library helpers: d_inode() annotations
VFS: assorted weird filesystems: d_inode() annotations
VFS: normal filesystems (and lustre): d_inode() annotations
VFS: security/: d_inode() annotations
VFS: security/: d_backing_inode() annotations
VFS: net/: d_inode() annotations
VFS: net/unix: d_backing_inode() annotations
VFS: kernel/: d_inode() annotations
VFS: audit: d_backing_inode() annotations
VFS: Fix up some ->d_inode accesses in the chelsio driver
VFS: Cachefiles should perform fs modifications on the top layer only
VFS: AF_UNIX sockets should call mknod on the top layer only
This series introduces preliminary ACPI 5.1 support to the arm64 kernel
using the "hardware reduced" profile. We don't support any peripherals
yet, so it's fairly limited in scope:
- Memory init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCgAGBQJVNOC2AAoJELescNyEwWM08dIH/1Pn5xa04wwNDn0MOpbuQMk2
kHM7hx69fbXflTJpnZRVyFBjRxxr5qilA7rljAFLnFeF8Fcll/s5VNy7ElHKLISq
CB0ywgUfOd/sFJH57rcc67pC1b/XuqTbE1u1NFwvp2R3j1kGAEJWNA6SyxIP4bbc
NO5jScx0lQOJ3rrPAXBW8qlGkeUk7TPOQJtMrpftNXlFLFrR63rPaEmMZ9dWepBF
aRE4GXPvyUhpyv5o9RvlN5l8bQttiRJ3f9QjyG7NYhX0PXH3DyvGUzYlk2IoZtID
v3ssCQH3uRsAZHIBhaTyNqFnUIaDR825bvGqyG/tj2Dt3kQZiF+QrfnU5D9TuMw=
=zLJn
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull initial ACPI support for arm64 from Will Deacon:
"This series introduces preliminary ACPI 5.1 support to the arm64
kernel using the "hardware reduced" profile. We don't support any
peripherals yet, so it's fairly limited in scope:
- MEMORY init (UEFI)
- ACPI discovery (RSDP via UEFI)
- CPU init (FADT)
- GIC init (MADT)
- SMP boot (MADT + PSCI)
- ACPI Kconfig options (dependent on EXPERT)
ACPI for arm64 has been in development for a while now and hardware
has been available that can boot with either FDT or ACPI tables. This
has been made possible by both changes to the ACPI spec to cater for
ARM-based machines (known as "hardware-reduced" in ACPI parlance) but
also a Linaro-driven effort to get this supported on top of the Linux
kernel. This pull request is the result of that work.
These changes allow us to initialise the CPUs, interrupt controller,
and timers via ACPI tables, with memory information and cmdline coming
from EFI. We don't support a hybrid ACPI/FDT scheme. Of course,
there is still plenty of work to do (a serial console would be nice!)
but I expect that to happen on a per-driver basis after this core
series has been merged.
Anyway, the diff stat here is fairly horrible, but splitting this up
and merging it via all the different subsystems would have been
extremely painful. Instead, we've got all the relevant Acks in place
and I've not seen anything other than trivial (Kconfig) conflicts in
-next (for completeness, I've included my resolution below). Nearly
half of the insertions fall under Documentation/.
So, we'll see how this goes. Right now, it all depends on EXPERT and
I fully expect people to use FDT by default for the immediate future"
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (31 commits)
ARM64 / ACPI: make acpi_map_gic_cpu_interface() as void function
ARM64 / ACPI: Ignore the return error value of acpi_map_gic_cpu_interface()
ARM64 / ACPI: fix usage of acpi_map_gic_cpu_interface
ARM64: kernel: acpi: honour acpi=force command line parameter
ARM64: kernel: acpi: refactor ACPI tables init and checks
ARM64: kernel: psci: let ACPI probe PSCI version
ARM64: kernel: psci: factor out probe function
ACPI: move arm64 GSI IRQ model to generic GSI IRQ layer
ARM64 / ACPI: Don't unflatten device tree if acpi=force is passed
ARM64 / ACPI: additions of ACPI documentation for arm64
Documentation: ACPI for ARM64
ARM64 / ACPI: Enable ARM64 in Kconfig
XEN / ACPI: Make XEN ACPI depend on X86
ARM64 / ACPI: Select ACPI_REDUCED_HARDWARE_ONLY if ACPI is enabled on ARM64
clocksource / arch_timer: Parse GTDT to initialize arch timer
irqchip: Add GICv2 specific ACPI boot support
ARM64 / ACPI: Introduce ACPI_IRQ_MODEL_GIC and register device's gsi
ACPI / processor: Make it possible to get CPU hardware ID via GICC
ACPI / processor: Introduce phys_cpuid_t for CPU hardware ID
ARM64 / ACPI: Parse MADT for SMP initialization
...
Refine the interfaces to create IRQ for DMAR unit. It's a preparation
for converting DMAR IRQ to hierarchical irqdomain on x86.
It also moves dmar_alloc_hwirq()/dmar_free_hwirq() from irq_remapping.h
to dmar.h. They are not irq_remapping specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Cohen <david.a.cohen@linux.intel.com>
Cc: Sander Eikelenboom <linux@eikelenboom.it>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: iommu@lists.linux-foundation.org
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dimitri Sivanich <sivanich@sgi.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Joerg Roedel <joro@8bytes.org>
Link: http://lkml.kernel.org/r/1428905519-23704-20-git-send-email-jiang.liu@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Prior to c770cb4cb5 ("PCI: Mark invalid BARs as unassigned"), if we tried
to claim a PCI BAR but could not find an upstream bridge window that
matched it, we complained but still allowed the device to be enabled.
c770cb4cb5 broke devices that previously worked (mptsas and igb in the
case Tony reported, but it could be any devices) because it marks those
BARs as IORESOURCE_UNSET, which makes pci_enable_device() complain and
return failure:
igb 0000:81:00.0: can't enable device: BAR 0 [mem size 0x00020000] not assigned
igb: probe of 0000:81:00.0 failed with error -22
The underlying cause is an ACPI Address Space Descriptor for a PCI host
bridge window that is marked as "consumer". This is a firmware defect:
resources that are produced on the downstream side of a bridge should be
marked "producer". But rejecting these BARs that we previously allowed is
a functionality regression, and firmware has not used the producer/consumer
bit consistently, so we can't rely on it anyway.
Stop checking the producer/consumer bit, and assume all bridge Address
Space Descriptors are for bridge windows.
Note that this change does not affect I/O Port or Fixed Location I/O Port
Descriptors, which are commonly used for the [io 0x0cf8-0x0cff] config
access range. That range is a "consumer" range and should not be treated
as a window.
Fixes: c770cb4cb5 ("PCI: Mark invalid BARs as unassigned")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=96961
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VAgA
-----END PGP SIGNATURE-----
Merge tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull final removal of deprecated cpus_* cpumask functions from Rusty Russell:
"This is the final removal (after several years!) of the obsolete
cpus_* functions, prompted by their mis-use in staging.
With these function removed, all cpu functions should only iterate to
nr_cpu_ids, so we finally only allocate that many bits when cpumasks
are allocated offstack"
* tag 'cpumask-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (25 commits)
cpumask: remove __first_cpu / __next_cpu
cpumask: resurrect CPU_MASK_CPU0
linux/cpumask.h: add typechecking to cpumask_test_cpu
cpumask: only allocate nr_cpumask_bits.
Fix weird uses of num_online_cpus().
cpumask: remove deprecated functions.
mips: fix obsolete cpumask_of_cpu usage.
x86: fix more deprecated cpu function usage.
ia64: remove deprecated cpus_ usage.
powerpc: fix deprecated CPU_MASK_CPU0 usage.
CPU_MASK_ALL/CPU_MASK_NONE: remove from deprecated region.
staging/lustre/o2iblnd: Don't use cpus_weight
staging/lustre/libcfs: replace deprecated cpus_ calls with cpumask_
staging/lustre/ptlrpc: Do not use deprecated cpus_* functions
blackfin: fix up obsolete cpu function usage.
parisc: fix up obsolete cpu function usage.
tile: fix up obsolete cpu function usage.
arm64: fix up obsolete cpu function usage.
mips: fix up obsolete cpu function usage.
x86: fix up obsolete cpu function usage.
...
Pull exec domain removal from Richard Weinberger:
"This series removes execution domain support from Linux.
The idea behind exec domains was to support different ABIs. The
feature was never complete nor stable. Let's rip it out and make the
kernel signal handling code less complicated"
* 'exec_domain_rip_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (27 commits)
arm64: Removed unused variable
sparc: Fix execution domain removal
Remove rest of exec domains.
arch: Remove exec_domain from remaining archs
arc: Remove signal translation and exec_domain
xtensa: Remove signal translation and exec_domain
xtensa: Autogenerate offsets in struct thread_info
x86: Remove signal translation and exec_domain
unicore32: Remove signal translation and exec_domain
um: Remove signal translation and exec_domain
tile: Remove signal translation and exec_domain
sparc: Remove signal translation and exec_domain
sh: Remove signal translation and exec_domain
s390: Remove signal translation and exec_domain
mn10300: Remove signal translation and exec_domain
microblaze: Remove signal translation and exec_domain
m68k: Remove signal translation and exec_domain
m32r: Remove signal translation and exec_domain
m32r: Autogenerate offsets in struct thread_info
frv: Remove signal translation and exec_domain
...
Pull kbuild updates from Michal Marek:
"Here is the first round of kbuild changes for v4.1-rc1:
- kallsyms fix for ARM and cleanup
- make dep(end) removed (developers have no sense of nostalgia these
days...)
- include Makefiles by relative path
- stop useless rebuilds of asm-offsets.h and bounds.h"
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: kallsyms: drop special handling of pre-3.0 GCC symbols
Kbuild: kallsyms: ignore veneers emitted by the ARM linker
kbuild: ia64: use $(src)/Makefile.gate rather than particular path
kbuild: include $(src)/Makefile rather than $(obj)/Makefile
kbuild: use relative path more to include Makefile
kbuild: use relative path to include Makefile
kbuild: do not add $(bounds-file) and $(offsets-file) to targets
kbuild: remove warning about "make depend"
kbuild: Don't reset timestamps in include/generated if not needed
We would want to use number of page table level to define mm_struct.
Let's expose it as CONFIG_PGTABLE_LEVELS.
We need to define PGTABLE_LEVELS before sourcing init/Kconfig:
arch/Kconfig will define default value and it's sourced from init/Kconfig.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "MAKEFLAGS += --include-dir=$(srctree)" line in the top Makefile
allows us to do this.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
CPU hardware ID (phys_id) is defined as u32 in structure acpi_processor,
but phys_id is used as int in acpi processor driver, so it will lead to
some inconsistence for the drivers.
Furthermore, to cater for ACPI arch ports that implement 64 bits CPU
ids a generic CPU physical id type is required.
So introduce typedef u32 phys_cpuid_t in a common file, and introduce
a macro PHYS_CPUID_INVALID as (phys_cpuid_t)(-1) if it's not defined
by other archs, this will solve the inconsistence in acpi processor driver,
and will prepare for the ACPI on ARM64 for the 64 bit CPU hardware ID
in the following patch.
CC: Rafael J Wysocki <rjw@rjwysocki.net>
Suggested-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Grant Likely <grant.likely@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[hj: reworked cpu physid map return codes]
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
ACPI 5.1 does not currently support S states for ARM64 hardware but
ACPI code will call acpi_target_system_state() and acpi_sleep_init()
for device power management, so introduce
CONFIG_ACPI_SYSTEM_POWER_STATES_SUPPORT and select it for x86 and
ia64 only to make sleep functions available, and also introduce stub
function to allow other drivers to function until S states are defined
for ARM64.
It will be no functional change for x86 and IA64.
Suggested-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Tomasz Nowicki <tomasz.nowicki@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Previously, pci_scan_root_bus() created a root PCI bus, enumerated the
devices on it, and called pci_bus_add_devices(), which made the devices
available for drivers to claim them.
Most callers assigned resources to devices after pci_scan_root_bus()
returns, which may be after drivers have claimed the devices. This is
incorrect; the PCI core should not change device resources while a driver
is managing the device.
Remove pci_bus_add_devices() from pci_scan_root_bus() and do it after any
resource assignment in the callers.
Note that ARM's pci_common_init_dev() already called pci_bus_add_devices()
after pci_scan_root_bus(), so we only need to remove the first call:
pci_common_init_dev
pcibios_init_hw
pci_scan_root_bus
pci_bus_add_devices # first call
pci_bus_assign_resources
pci_bus_add_devices # second call
[bhelgaas: changelog, drop "root_bus" var in alpha common_init_pci(),
return failure earlier in mn10300, add "return" in x86 pcibios_scan_root(),
return early if xtensa platform_pcibios_fixup() fails]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
CC: Matt Turner <mattst88@gmail.com>
CC: David Howells <dhowells@redhat.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Michal Simek <monstr@monstr.eu>
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Chris Metcalf <cmetcalf@ezchip.com>
CC: Chris Zankel <chris@zankel.net>
CC: Max Filippov <jcmvbkbc@gmail.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Thanks to spatch, then a sweep for for_each_cpu_mask => for_each_cpu.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Just a bit of manual neatening, before spatch cleans the rest.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Like in 3.19, I once more have a multi-stage cleanup for one asm-generic
header file, this time the work was done by Michael Tsirkin and cleans
up the uaccess.h file in asm-generic, as well as all architectures for
which the respective maintainers did not pick up his patches directly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LROx
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic uaccess.h cleanup from Arnd Bergmann:
"Like in 3.19, I once more have a multi-stage cleanup for one
asm-generic header file, this time the work was done by Michael
Tsirkin and cleans up the uaccess.h file in asm-generic, as well as
all architectures for which the respective maintainers did not pick up
his patches directly"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (37 commits)
sparc32: nocheck uaccess coding style tweaks
sparc64: nocheck uaccess coding style tweaks
xtensa: macro whitespace fixes
sh: macro whitespace fixes
parisc: macro whitespace fixes
m68k: macro whitespace fixes
m32r: macro whitespace fixes
frv: macro whitespace fixes
cris: macro whitespace fixes
avr32: macro whitespace fixes
arm64: macro whitespace fixes
arm: macro whitespace fixes
alpha: macro whitespace fixes
blackfin: macro whitespace fixes
sparc64: uaccess_64 macro whitespace fixes
sparc32: uaccess_32 macro whitespace fixes
avr32: whitespace fix
sh: fix put_user sparse errors
metag: fix put_user sparse errors
ia64: fix put_user sparse errors
...
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Common: Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other architectures).
This can improve latency up to 50% on some scenarios (e.g. O_DSYNC writes
or TCP_RR netperf tests). This also has to be enabled manually for now,
but the plan is to auto-tune this in the future.
ARM/ARM64: the highlights are support for GICv3 emulation and dirty page
tracking
s390: several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS: Bugfixes.
x86: Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested virtualization
improvements (nested APICv---a nice optimization), usual round of emulation
fixes. There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
ARM has other conflicts where functions are added in the same place
by 3.19-rc and 3.20 patches. These are not large though, and entirely
within KVM.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJU28rkAAoJEL/70l94x66DXqQH/1TDOfJIjW7P2kb0Sw7Fy1wi
cEX1KO/VFxAqc8R0E/0Wb55CXyPjQJM6xBXuFr5cUDaIjQ8ULSktL4pEwXyyv/s5
DBDkN65mriry2w5VuEaRLVcuX9Wy+tqLQXWNkEySfyb4uhZChWWHvKEcgw5SqCyg
NlpeHurYESIoNyov3jWqvBjr4OmaQENyv7t2c6q5ErIgG02V+iCux5QGbphM2IC9
LFtPKxoqhfeB2xFxTOIt8HJiXrZNwflsTejIlCl/NSEiDVLLxxHCxK2tWK/tUXMn
JfLD9ytXBWtNMwInvtFm4fPmDouv2VDyR0xnK2db+/axsJZnbxqjGu1um4Dqbak=
=7gdx
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"Fairly small update, but there are some interesting new features.
Common:
Optional support for adding a small amount of polling on each HLT
instruction executed in the guest (or equivalent for other
architectures). This can improve latency up to 50% on some
scenarios (e.g. O_DSYNC writes or TCP_RR netperf tests). This
also has to be enabled manually for now, but the plan is to
auto-tune this in the future.
ARM/ARM64:
The highlights are support for GICv3 emulation and dirty page
tracking
s390:
Several optimizations and bugfixes. Also a first: a feature
exposed by KVM (UUID and long guest name in /proc/sysinfo) before
it is available in IBM's hypervisor! :)
MIPS:
Bugfixes.
x86:
Support for PML (page modification logging, a new feature in
Broadwell Xeons that speeds up dirty page tracking), nested
virtualization improvements (nested APICv---a nice optimization),
usual round of emulation fixes.
There is also a new option to reduce latency of the TSC deadline
timer in the guest; this needs to be tuned manually.
Some commits are common between this pull and Catalin's; I see you
have already included his tree.
Powerpc:
Nothing yet.
The KVM/PPC changes will come in through the PPC maintainers,
because I haven't received them yet and I might end up being
offline for some part of next week"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (130 commits)
KVM: ia64: drop kvm.h from installed user headers
KVM: x86: fix build with !CONFIG_SMP
KVM: x86: emulate: correct page fault error code for NoWrite instructions
KVM: Disable compat ioctl for s390
KVM: s390: add cpu model support
KVM: s390: use facilities and cpu_id per KVM
KVM: s390/CPACF: Choose crypto control block format
s390/kernel: Update /proc/sysinfo file with Extended Name and UUID
KVM: s390: reenable LPP facility
KVM: s390: floating irqs: fix user triggerable endless loop
kvm: add halt_poll_ns module parameter
kvm: remove KVM_MMIO_SIZE
KVM: MIPS: Don't leak FPU/DSP to guest
KVM: MIPS: Disable HTW while in guest
KVM: nVMX: Enable nested posted interrupt processing
KVM: nVMX: Enable nested virtual interrupt delivery
KVM: nVMX: Enable nested apic register virtualization
KVM: nVMX: Make nested control MSRs per-cpu
KVM: nVMX: Enable nested virtualize x2apic mode
KVM: nVMX: Prepare for using hardware MSR bitmap
...
If an attacker can cause a controlled kernel stack overflow, overwriting
the restart block is a very juicy exploit target. This is because the
restart_block is held in the same memory allocation as the kernel stack.
Moving the restart block to struct task_struct prevents this exploit by
making the restart_block harder to locate.
Note that there are other fields in thread_info that are also easy
targets, at least on some architectures.
It's also a decent simplification, since the restart code is more or less
identical on all architectures.
[james.hogan@imgtec.com: metag: align thread_info::supervisor_stack]
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Richard Weinberger <richard@nod.at>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Acked-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Tested-by: Michael Ellerman <mpe@ellerman.id.au> (powerpc)
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Chris Zankel <chris@zankel.net>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
LKP has triggered a compiler warning after my recent patch "mm: account
pmd page tables to the process":
mm/mmap.c: In function 'exit_mmap':
>> mm/mmap.c:2857:2: warning: right shift count >= width of type [enabled by default]
The code:
> 2857 WARN_ON(mm_nr_pmds(mm) >
2858 round_up(FIRST_USER_ADDRESS, PUD_SIZE) >> PUD_SHIFT);
In this, on tile, we have FIRST_USER_ADDRESS defined as 0. round_up() has
the same type -- int. PUD_SHIFT.
I think the best way to fix it is to define FIRST_USER_ADDRESS as unsigned
long. On every arch for consistency.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently we have many duplicates in definitions around
follow_huge_addr(), follow_huge_pmd(), and follow_huge_pud(), so this
patch tries to remove the m. The basic idea is to put the default
implementation for these functions in mm/hugetlb.c as weak symbols
(regardless of CONFIG_ARCH_WANT_GENERAL_HUGETL B), and to implement
arch-specific code only when the arch needs it.
For follow_huge_addr(), only powerpc and ia64 have their own
implementation, and in all other architectures this function just returns
ERR_PTR(-EINVAL). So this patch sets returning ERR_PTR(-EINVAL) as
default.
As for follow_huge_(pmd|pud)(), if (pmd|pud)_huge() is implemented to
always return 0 in your architecture (like in ia64 or sparc,) it's never
called (the callsite is optimized away) no matter how implemented it is.
So in such architectures, we don't need arch-specific implementation.
In some architecture (like mips, s390 and tile,) their current
arch-specific follow_huge_(pmd|pud)() are effectively identical with the
common code, so this patch lets these architecture use the common code.
One exception is metag, where pmd_huge() could return non-zero but it
expects follow_huge_pmd() to always return NULL. This means that we need
arch-specific implementation which returns NULL. This behavior looks
strange to me (because non-zero pmd_huge() implies that the architecture
supports PMD-based hugepage, so follow_huge_pmd() can/should return some
relevant value,) but that's beyond this cleanup patch, so let's keep it.
Justification of non-trivial changes:
- in s390, follow_huge_pmd() checks !MACHINE_HAS_HPAGE at first, and this
patch removes the check. This is OK because we can assume MACHINE_HAS_HPAGE
is true when follow_huge_pmd() can be called (note that pmd_huge() has
the same check and always returns 0 for !MACHINE_HAS_HPAGE.)
- in s390 and mips, we use HPAGE_MASK instead of PMD_MASK as done in common
code. This patch forces these archs use PMD_MASK, but it's OK because
they are identical in both archs.
In s390, both of HPAGE_SHIFT and PMD_SHIFT are 20.
In mips, HPAGE_SHIFT is defined as (PAGE_SHIFT + PAGE_SHIFT - 3) and
PMD_SHIFT is define as (PAGE_SHIFT + PAGE_SHIFT + PTE_ORDER - 3), but
PTE_ORDER is always 0, so these are identical.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Hugh Dickins <hughd@google.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Lee Schermerhorn <lee.schermerhorn@hp.com>
Cc: Steve Capper <steve.capper@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc updates from Andrew Morton:
"Bite-sized chunks this time, to avoid the MTA ratelimiting woes.
- fs/notify updates
- ocfs2
- some of MM"
That laconic "some MM" is mainly the removal of remap_file_pages(),
which is a big simplification of the VM, and which gets rid of a *lot*
of random cruft and special cases because we no longer support the
non-linear mappings that it used.
From a user interface perspective, nothing has changed, because the
remap_file_pages() syscall still exists, it's just done by emulating the
old behavior by creating a lot of individual small mappings instead of
one non-linear one.
The emulation is slower than the old "native" non-linear mappings, but
nobody really uses or cares about remap_file_pages(), and simplifying
the VM is a big advantage.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (78 commits)
memcg: zap memcg_slab_caches and memcg_slab_mutex
memcg: zap memcg_name argument of memcg_create_kmem_cache
memcg: zap __memcg_{charge,uncharge}_slab
mm/page_alloc.c: place zone_id check before VM_BUG_ON_PAGE check
mm: hugetlb: fix type of hugetlb_treat_as_movable variable
mm, hugetlb: remove unnecessary lower bound on sysctl handlers"?
mm: memory: merge shared-writable dirtying branches in do_wp_page()
mm: memory: remove ->vm_file check on shared writable vmas
xtensa: drop _PAGE_FILE and pte_file()-related helpers
x86: drop _PAGE_FILE and pte_file()-related helpers
unicore32: drop pte_file()-related helpers
um: drop _PAGE_FILE and pte_file()-related helpers
tile: drop pte_file()-related helpers
sparc: drop pte_file()-related helpers
sh: drop _PAGE_FILE and pte_file()-related helpers
score: drop _PAGE_FILE and pte_file()-related helpers
s390: drop pte_file()-related helpers
parisc: drop _PAGE_FILE and pte_file()-related helpers
openrisc: drop _PAGE_FILE and pte_file()-related helpers
nios2: drop _PAGE_FILE and pte_file()-related helpers
...
We've replaced remap_file_pages(2) implementation with emulation. Nobody
creates non-linear mapping anymore.
This patch also increase number of bits availble for swap offset.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* acpi-doc:
MAINTAINERS / ACPI: add the necessary '/' according to entry rules
ACPI / Documentation: add a missing '='
* acpi-pm:
ACPI / sleep: mark acpi_sleep_dmi_check() __init
* acpi-pcc:
ACPI / PCC: Use pr_debug() for debug messages in pcc_init()
* acpi-tables:
ACPI / table: remove duplicate NULL check for the handler of acpi_table_parse()
* acpica:
ACPICA: Events: Enable APIs to allow interrupt/polling adaptive request based GPE handling model
ACPICA: Events: Introduce acpi_set_gpe()/acpi_finish_gpe() to reduce divergences
ACPICA: Events: Introduce ACPI_GPE_DISPATCH_RAW_HANDLER to fix 2 issues for the current GPE APIs
ACPICA: Update version to 20150204
ACPICA: Update Copyright headers to 2015
ACPICA: Hardware: Cast GPE enable_mask before storing
ACPICA: Events: Cleanup GPE dispatcher type obtaining code
ACPICA: Events: Cleanup to move acpi_gbl_global_event_handler invocation out of acpi_ev_gpe_dispatch()
ACPICA: Events: Cleanup of resetting the GPE handler to NULL before removing
ACPICA: Events: Fix uninitialized variable
ACPICA: Events: Remove acpi_ev_valid_gpe_event() due to current restriction
ACPICA: Events: Remove duplicated sanity check in acpi_ev_enable_gpe()
ACPICA: Events: Back port "ACPICA: Save current masks of enabled GPEs after enable register writes"
ACPICA: Resources: Provide common part for struct acpi_resource_address structures.
ACPI: Introduce acpi_unload_parent_table() usages in Linux kernel
ACPICA: take ACPI_MTX_INTERPRETER in acpi_unload_table_id()
The header was deleted, so stop trying to install it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
In acpi_table_parse(), pointer of the table to pass to handler() is
checked before handler() called, so remove all the duplicate NULL
check in the handler function.
CC: Tony Luck <tony.luck@intel.com>
CC: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The core VM already knows about VM_FAULT_SIGBUS, but cannot return a
"you should SIGSEGV" error, because the SIGSEGV case was generally
handled by the caller - usually the architecture fault handler.
That results in lots of duplication - all the architecture fault
handlers end up doing very similar "look up vma, check permissions, do
retries etc" - but it generally works. However, there are cases where
the VM actually wants to SIGSEGV, and applications _expect_ SIGSEGV.
In particular, when accessing the stack guard page, libsigsegv expects a
SIGSEGV. And it usually got one, because the stack growth is handled by
that duplicated architecture fault handler.
However, when the generic VM layer started propagating the error return
from the stack expansion in commit fee7e49d45 ("mm: propagate error
from stack expansion even for guard page"), that now exposed the
existing VM_FAULT_SIGBUS result to user space. And user space really
expected SIGSEGV, not SIGBUS.
To fix that case, we need to add a VM_FAULT_SIGSEGV, and teach all those
duplicate architecture fault handlers about it. They all already have
the code to handle SIGSEGV, so it's about just tying that new return
value to the existing code, but it's all a bit annoying.
This is the mindless minimal patch to do this. A more extensive patch
would be to try to gather up the mostly shared fault handling logic into
one generic helper routine, and long-term we really should do that
cleanup.
Just from this patch, you can generally see that most architectures just
copied (directly or indirectly) the old x86 way of doing things, but in
the meantime that original x86 model has been improved to hold the VM
semaphore for shorter times etc and to handle VM_FAULT_RETRY and other
"newer" things, so it would be a good idea to bring all those
improvements to the generic case and teach other architectures about
them too.
Reported-and-tested-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Jan Engelhardt <jengelh@inai.de>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com> # "s390 still compiles and boots"
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct acpi_resource_address and struct acpi_resource_extended_address64 share substracts
just at different offsets. To unify the parsing functions, OSPMs like Linux
need a new ACPI_ADDRESS64_ATTRIBUTE as their substructs, so they can
extract the shared data.
This patch also synchronizes the structure changes to the Linux kernel.
The usages are searched by matching the following keywords:
1. acpi_resource_address
2. acpi_resource_extended_address
3. ACPI_RESOURCE_TYPE_ADDRESS
4. ACPI_RESOURCE_TYPE_EXTENDED_ADDRESS
And we found and fixed the usages in the following files:
arch/ia64/kernel/acpi-ext.c
arch/ia64/pci/pci.c
arch/x86/pci/acpi.c
arch/x86/pci/mmconfig-shared.c
drivers/xen/xen-acpi-memhotplug.c
drivers/acpi/acpi_memhotplug.c
drivers/acpi/pci_root.c
drivers/acpi/resource.c
drivers/char/hpet.c
drivers/pnp/pnpacpi/rsparser.c
drivers/hv/vmbus_drv.c
Build tests are passed with defconfig/allnoconfig/allyesconfig and
defconfig+CONFIG_ACPI=n.
Original-by: Thomas Gleixner <tglx@linutronix.de>
Original-by: Jiang Liu <jiang.liu@linux.intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Resource management
- Clip bridge windows to fit in upstream windows (Yinghai Lu)
Virtualization
- Mark Atheros AR93xx to avoid using bus reset (Alex Williamson)
Miscellaneous
- Update Richard Zhu's email address (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HRy7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for:
- a resource management problem that causes a Radeon "Fatal error
during GPU init" on machines where the BIOS programmed an invalid
Root Port window. This was a regression in v3.16.
- an Atheros AR93xx device that doesn't handle PCI bus resets
correctly. This was a regression in v3.14.
- an out-of-date email address"
* tag 'pci-v3.19-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
MAINTAINERS: Update Richard Zhu's email address
sparc/PCI: Clip bridge windows to fit in upstream windows
powerpc/PCI: Clip bridge windows to fit in upstream windows
parisc/PCI: Clip bridge windows to fit in upstream windows
mn10300/PCI: Clip bridge windows to fit in upstream windows
microblaze/PCI: Clip bridge windows to fit in upstream windows
ia64/PCI: Clip bridge windows to fit in upstream windows
frv/PCI: Clip bridge windows to fit in upstream windows
alpha/PCI: Clip bridge windows to fit in upstream windows
x86/PCI: Clip bridge windows to fit in upstream windows
PCI: Add pci_claim_bridge_resource() to clip window if necessary
PCI: Add pci_bus_clip_resource() to clip to fit upstream window
PCI: Pass bridge device, not bus, when updating bridge windows
PCI: Mark Atheros AR93xx to avoid bus reset
PCI: Add flag for devices where we can't use bus reset
First two are minor fallout from the param rework which went in this merge
window.
Next three are a series which fixes a longstanding (but never previously
reported and unlikely , so no CC stable) race between kallsyms and freeing
the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload.
Thanks,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Kf9b
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module and param fixes from Rusty Russell:
"Surprising number of fixes this merge window :(
The first two are minor fallout from the param rework which went in
this merge window.
The next three are a series which fixes a longstanding (but never
previously reported and unlikely , so no CC stable) race between
kallsyms and freeing the init section.
Finally, a minor cleanup as our module refcount will now be -1 during
unload"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: make module_refcount() a signed integer.
module: fix race in kallsyms resolution during module load success.
module: remove mod arg from module_free, rename module_memfree().
module_arch_freeing_init(): new hook for archs before module->module_init freed.
param: fix uninitialized read with CONFIG_DEBUG_LOCK_ALLOC
param: initialize store function to NULL if not available.
Archs have been abusing module_free() to clean up their arch-specific
allocations. Since module_free() is also (ab)used by BPF and trace code,
let's keep it to simple allocations, and provide a hook called before
that.
This means that avr32, ia64, parisc and s390 no longer need to implement
their own module_free() at all. avr32 doesn't need module_finalize()
either.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Chris Metcalf <cmetcalf@ezchip.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Every PCI-PCI bridge window should fit inside an upstream bridge window
because orphaned address space is unreachable from the primary side of the
upstream bridge. If we inherit invalid bridge windows that overlap an
upstream window from firmware, clip them to fit and update the bridge
accordingly.
[bhelgaas: changelog]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=85491
Reported-by: Marek Kordik <kordikmarek@gmail.com>
Fixes: 5b28541552 ("PCI: Restrict 64-bit prefetchable bridge windows to 64-bit resources")
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tony Luck <tony.luck@intel.com>
CC: Fenghua Yu <fenghua.yu@intel.com>
CC: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
CC: linux-ia64@vger.kernel.org
At the moment, if p and x are both tagged as bitwise types,
some of get_user(x, p), put_user(x, p), __get_user(x, p), __put_user(x, p)
might produce a sparse warning on many architectures.
This is a false positive: *p on these architectures is loaded into long
(typically using asm), then cast back to typeof(*p).
When typeof(*p) is a bitwise type (which is uncommon), such a cast needs
__force, otherwise sparse produces a warning.
Some architectures already have the __force tag, add it
where it's missing.
I verified that adding these __force casts does not supress any useful warnings.
Specifically, vhost wants to read/write bitwise types in userspace memory
using get_user/put_user.
At the moment this triggers sparse errors, since the value is passed through an
integer.
For example:
__le32 __user *p;
__u32 x;
both
put_user(x, p);
and
get_user(x, p);
should be safe, but produce warnings on some architectures.
While there, I noticed that a bunch of architectures violated
coding style rules within uaccess macros.
Included patches to fix them up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUtS+YAAoJECgfDbjSjVRpQ/QIAKXOc6tMXo+r/F32YC0Fv74G
W4VKIk7u9XQNjOzez9i+xce75YBDBKHk5R9kLCfAg6Zew+6NRgbBV+QjGVB8dpot
2GxajcVhOySgaR45sGK3Ldg5yVz5ficqZEyYWKNgYeyMWJdlpvUk+4W5q15TiPZe
u+C57/KzfRMDHyv3UkwAbqrkYGE0h7vXBi0BmOdCJlbKjG+6kFoVU/dAWsByDD5p
q54ji8UdIkh2oyH5qhSbAwQN4Cg5N37Agw86HwltjQFJAVvV3yPRUsv7MQnpRB1+
hKlPXPUarNozGVV7OlcvGa9Lvz8m3a2rNd9+1tgHY0Fpia1JYAY2UdubS99fl5E=
=LVcN
-----END PGP SIGNATURE-----
Merge tag 'uaccess_for_upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost into asm-generic
Merge "uaccess: fix sparse warning on get/put_user for bitwise types" from Michael S. Tsirkin:
At the moment, if p and x are both tagged as bitwise types,
some of get_user(x, p), put_user(x, p), __get_user(x, p), __put_user(x, p)
might produce a sparse warning on many architectures.
This is a false positive: *p on these architectures is loaded into long
(typically using asm), then cast back to typeof(*p).
When typeof(*p) is a bitwise type (which is uncommon), such a cast needs
__force, otherwise sparse produces a warning.
Some architectures already have the __force tag, add it
where it's missing.
I verified that adding these __force casts does not supress any useful warnings.
Specifically, vhost wants to read/write bitwise types in userspace memory
using get_user/put_user.
At the moment this triggers sparse errors, since the value is passed through an
integer.
For example:
__le32 __user *p;
__u32 x;
both
put_user(x, p);
and
get_user(x, p);
should be safe, but produce warnings on some architectures.
While there, I noticed that a bunch of architectures violated
coding style rules within uaccess macros.
Included patches to fix them up.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'uaccess_for_upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (37 commits)
sparc32: nocheck uaccess coding style tweaks
sparc64: nocheck uaccess coding style tweaks
xtensa: macro whitespace fixes
sh: macro whitespace fixes
parisc: macro whitespace fixes
m68k: macro whitespace fixes
m32r: macro whitespace fixes
frv: macro whitespace fixes
cris: macro whitespace fixes
avr32: macro whitespace fixes
arm64: macro whitespace fixes
arm: macro whitespace fixes
alpha: macro whitespace fixes
blackfin: macro whitespace fixes
sparc64: uaccess_64 macro whitespace fixes
sparc32: uaccess_32 macro whitespace fixes
avr32: whitespace fix
sh: fix put_user sparse errors
metag: fix put_user sparse errors
ia64: fix put_user sparse errors
...
virtio wants to write bitwise types to userspace using put_user.
At the moment this triggers sparse errors, since the value is passed
through an integer.
For example:
__le32 __user *p;
__le32 x;
put_user(x, p);
is safe, but currently triggers a sparse warning.
Fix that up using __force.
Note: this does not suppress any useful sparse checks since callers
do a cast (__typeof__(*(ptr))) (x) which in turn forces all the
necessary type checks.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
virtio wants to read bitwise types from userspace using get_user. At the
moment this triggers sparse errors, since the value is passed through an
integer.
Fix that up using __force.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
* acpi-pm:
ACPI / PM: Fix PM initialization for devices that are not present
* acpi-processor:
ACPI / processor: Rename acpi_(un)map_lsapic() to acpi_(un)map_cpu()
ACPI / processor: Convert apic_id to phys_id to make it arch agnostic
* acpi-video:
ACPI / video: Add disable_native_backlight quirk for Dell XPS15 L521X
acpi_map_lsapic() will allocate a logical CPU number and map it to
physical CPU id (such as APIC id) for the hot-added CPU, it will also
do some mapping for NUMA node id and etc, acpi_unmap_lsapic() will
do the reverse.
We can see that the name of the function is a little bit confusing and
arch (IA64) dependent so rename them as acpi_(un)map_cpu() to make arch
agnostic and explicit.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XF9K
-----END PGP SIGNATURE-----
Merge tag 'please-pull-misc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 __get_cpu_var removal from Tony Luck:
"__get_cpu_var removed from rest of tree, drop reference from comments
in arch/ia64"
* tag 'please-pull-misc-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Update comment that references __get_cpu_var
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by
the driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken
into account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should
have used from the start and drop some other unuseful KERN_ERR
messages printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool
(Prarit Bhargava).
- Fix two regressions introduced by recent commits in the OPP
library and clean up some existing minor issues in that code
(Viresh Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout
the tree (or drop it where that can be done) in order to make
it possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki,
Ulf Hansson, Ludovic Desroches). There will be one more
"CONFIG_PM_RUNTIME removal" batch after this one, because some
new uses of it have been introduced during the current merge
window, but that should be sufficient to finally get rid of it.
- Make the ACPI EC driver more robust against race conditions
related to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to
disable GPEs that it has not enabled which confuses ACPICA
and makes it report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver
to make it possible to override the blacklisting of some
systems in that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS
entry for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces
witn names that reflect the IDs of the ACPI device objects
they are associated with, except for "generic" ACPI fans
(PNP ID "PNP0C0B"). That's necessary for user space thermal
management tools to be able to connect the fans with the
parts of the system they are supposed to be cooling properly.
From Srinivas Pandruvada.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5fo2
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more ACPI and power management updates from Rafael Wysocki:
"These are regression fixes (leds-gpio, ACPI backlight driver,
operating performance points library, ACPI device enumeration
messages, cpupower tool), other bug fixes (ACPI EC driver, ACPI device
PM), some cleanups in the operating performance points (OPP)
framework, continuation of CONFIG_PM_RUNTIME elimination, a couple of
minor intel_pstate driver changes, a new MAINTAINERS entry for it and
an ACPI fan driver change needed for better support of thermal
management in user space.
Specifics:
- Fix a regression in leds-gpio introduced by a recent commit that
inadvertently changed the name of one of the properties used by the
driver (Fabio Estevam).
- Fix a regression in the ACPI backlight driver introduced by a
recent fix that missed one special case that had to be taken into
account (Aaron Lu).
- Drop the level of some new kernel messages from the ACPI core
introduced by a recent commit to KERN_DEBUG which they should have
used from the start and drop some other unuseful KERN_ERR messages
printed by ACPI (Rafael J Wysocki).
- Revert an incorrect commit modifying the cpupower tool (Prarit
Bhargava).
- Fix two regressions introduced by recent commits in the OPP library
and clean up some existing minor issues in that code (Viresh
Kumar).
- Continue to replace CONFIG_PM_RUNTIME with CONFIG_PM throughout the
tree (or drop it where that can be done) in order to make it
possible to eliminate CONFIG_PM_RUNTIME (Rafael J Wysocki, Ulf
Hansson, Ludovic Desroches).
There will be one more "CONFIG_PM_RUNTIME removal" batch after this
one, because some new uses of it have been introduced during the
current merge window, but that should be sufficient to finally get
rid of it.
- Make the ACPI EC driver more robust against race conditions related
to GPE handler installation failures (Lv Zheng).
- Prevent the ACPI device PM core code from attempting to disable
GPEs that it has not enabled which confuses ACPICA and makes it
report errors unnecessarily (Rafael J Wysocki).
- Add a "force" command line switch to the intel_pstate driver to
make it possible to override the blacklisting of some systems in
that driver if needed (Ethan Zhao).
- Improve intel_pstate code documentation and add a MAINTAINERS entry
for it (Kristen Carlson Accardi).
- Make the ACPI fan driver create cooling device interfaces witn
names that reflect the IDs of the ACPI device objects they are
associated with, except for "generic" ACPI fans (PNP ID "PNP0C0B").
That's necessary for user space thermal management tools to be able
to connect the fans with the parts of the system they are supposed
to be cooling properly. From Srinivas Pandruvada"
* tag 'pm+acpi-3.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
MAINTAINERS: add entry for intel_pstate
ACPI / video: update the skip case for acpi_video_device_in_dod()
power / PM: Eliminate CONFIG_PM_RUNTIME
NFC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
SCSI / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / EC: Fix unexpected ec_remove_handlers() invocations
Revert "tools: cpupower: fix return checks for sysfs_get_idlestate_count()"
tracing / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
x86 / PM: Replace CONFIG_PM_RUNTIME in io_apic.c
PM: Remove the SET_PM_RUNTIME_PM_OPS() macro
mmc: atmel-mci: use SET_RUNTIME_PM_OPS() macro
PM / Kconfig: Replace PM_RUNTIME with PM in dependencies
ARM / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
sound / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
phy / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
video / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tty / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM
ACPI / PM: Do not disable wakeup GPEs that have not been enabled
ACPI / utils: Drop error messages from acpi_evaluate_reference()
...
- spring cleaning: removed support for IA64, and for hardware-assisted
virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken because
the (non-KVM) XSAVES patches inadvertently changed the KVM userspace
ABI whenever XSAVES was enabled; hence, this part is going to stable.
Guest support is just a matter of exposing the feature and CPUID leaves
support.
Right now KVM is broken for PPC BookE in your tree (doesn't compile).
I'll reply to the pull request with a patch, please apply it either
before the pull request or in the merge commit, in order to preserve
bisectability somewhat.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJUkpg+AAoJEL/70l94x66DUmoH/jzXYkptSW9NGgm79KqxGJlD
lzLnLBkitVvx++Mz5YBhdJEhKKLUlCtifFT1zPJQ/pthQhIRSaaAwZyNGgUs5w5x
yMGKHiPQFyZRbmQtZhCInW0BftJoYHHciO3nUfHCZnp34My9MP2D55W7/z+fYFfQ
DuqBSE9ThyZJtZ4zh8NRA9fCOeuqwVYRyoBs820Wbsh4cpIBoIK63Dg7k+CLE+ZV
MZa/mRL6bAfsn9W5bnOUAgHJ3SPznnWbO3/g0aV+roL/5pffblprJx9lKNR08xUM
6hDFLop2gDehDJesDkY/o8Ckp1hEouvfsVpSShry4vcgtn0hgh2O5/6Orbmj6vE=
=Zwq1
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM update from Paolo Bonzini:
"3.19 changes for KVM:
- spring cleaning: removed support for IA64, and for hardware-
assisted virtualization on the PPC970
- ARM, PPC, s390 all had only small fixes
For x86:
- small performance improvements (though only on weird guests)
- usual round of hardware-compliancy fixes from Nadav
- APICv fixes
- XSAVES support for hosts and guests. XSAVES hosts were broken
because the (non-KVM) XSAVES patches inadvertently changed the KVM
userspace ABI whenever XSAVES was enabled; hence, this part is
going to stable. Guest support is just a matter of exposing the
feature and CPUID leaves support"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (179 commits)
KVM: move APIC types to arch/x86/
KVM: PPC: Book3S: Enable in-kernel XICS emulation by default
KVM: PPC: Book3S HV: Improve H_CONFER implementation
KVM: PPC: Book3S HV: Fix endianness of instruction obtained from HEIR register
KVM: PPC: Book3S HV: Remove code for PPC970 processors
KVM: PPC: Book3S HV: Tracepoints for KVM HV guest interactions
KVM: PPC: Book3S HV: Simplify locking around stolen time calculations
arch: powerpc: kvm: book3s_paired_singles.c: Remove unused function
arch: powerpc: kvm: book3s_pr.c: Remove unused function
arch: powerpc: kvm: book3s.c: Remove some unused functions
arch: powerpc: kvm: book3s_32_mmu.c: Remove unused function
KVM: PPC: Book3S HV: Check wait conditions before sleeping in kvmppc_vcore_blocked
KVM: PPC: Book3S HV: ptes are big endian
KVM: PPC: Book3S HV: Fix inaccuracies in ICP emulation for H_IPI
KVM: PPC: Book3S HV: Fix KSM memory corruption
KVM: PPC: Book3S HV: Fix an issue where guest is paused on receiving HMI
KVM: PPC: Book3S HV: Fix computation of tlbie operand
KVM: PPC: Book3S HV: Add missing HPTE unlock
KVM: PPC: BookE: Improve irq inject tracepoint
arm/arm64: KVM: Require in-kernel vgic for the arch timers
...
Pull vfs pile #2 from Al Viro:
"Next pile (and there'll be one or two more).
The large piece in this one is getting rid of /proc/*/ns/* weirdness;
among other things, it allows to (finally) make nameidata completely
opaque outside of fs/namei.c, making for easier further cleanups in
there"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
coda_venus_readdir(): use file_inode()
fs/namei.c: fold link_path_walk() call into path_init()
path_init(): don't bother with LOOKUP_PARENT in argument
fs/namei.c: new helper (path_cleanup())
path_init(): store the "base" pointer to file in nameidata itself
make default ->i_fop have ->open() fail with ENXIO
make nameidata completely opaque outside of fs/namei.c
kill proc_ns completely
take the targets of /proc/*/ns/* symlinks to separate fs
bury struct proc_ns in fs/proc
copy address of proc_ns_ops into ns_common
new helpers: ns_alloc_inum/ns_free_inum
make proc_ns_operations work with struct ns_common * instead of void *
switch the rest of proc_ns_operations to working with &...->ns
netns: switch ->get()/->put()/->install()/->inum() to working with &net->ns
make mntns ->get()/->put()/->install()/->inum() work with &mnt_ns->ns
common object embedded into various struct ....ns
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so Kconfig options
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace PM_RUNTIME with PM in Kconfig dependencies throughout the
tree.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Tejun Heo <tj@kernel.org>
There are a number of situations where the mandatory barriers rmb() and
wmb() are used to order memory/memory operations in the device drivers
and those barriers are much heavier than they actually need to be. For
example in the case of PowerPC wmb() calls the heavy-weight sync
instruction when for coherent memory operations all that is really needed
is an lsync or eieio instruction.
This commit adds a coherent only version of the mandatory memory barriers
rmb() and wmb(). In most cases this should result in the barrier being the
same as the SMP barriers for the SMP case, however in some cases we use a
barrier that is somewhere in between rmb() and smp_rmb(). For example on
ARM the rmb barriers break down as follows:
Barrier Call Explanation
--------- -------- ----------------------------------
rmb() dsb() Data synchronization barrier - system
dma_rmb() dmb(osh) data memory barrier - outer sharable
smp_rmb() dmb(ish) data memory barrier - inner sharable
These new barriers are not as safe as the standard rmb() and wmb().
Specifically they do not guarantee ordering between coherent and incoherent
memories. The primary use case for these would be to enforce ordering of
reads and writes when accessing coherent memory that is shared between the
CPU and a device.
It may also be noted that there is no dma_mb(). Most architectures don't
provide a good mechanism for performing a coherent only full barrier without
resorting to the same mechanism used in mb(). As such there isn't much to
be gained in trying to define such a function.
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: David Miller <davem@davemloft.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is meant to cleanup the handling of read_barrier_depends and
smp_read_barrier_depends. In multiple spots in the kernel headers
read_barrier_depends is defined as "do {} while (0)", however we then go
into the SMP vs non-SMP sections and have the SMP version reference
read_barrier_depends, and the non-SMP define it as yet another empty
do/while.
With this commit I went through and cleaned out the duplicate definitions
and reduced the number of definitions down to 2 per header. In addition I
moved the 50 line comments for the macro from the x86 and mips headers that
defined it as an empty do/while to those that were actually defining the
macro, alpha and blackfin.
Signed-off-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) New offloading infrastructure and example 'rocker' driver for
offloading of switching and routing to hardware.
This work was done by a large group of dedicated individuals, not
limited to: Scott Feldman, Jiri Pirko, Thomas Graf, John Fastabend,
Jamal Hadi Salim, Andy Gospodarek, Florian Fainelli, Roopa Prabhu
2) Start making the networking operate on IOV iterators instead of
modifying iov objects in-situ during transfers. Thanks to Al Viro
and Herbert Xu.
3) A set of new netlink interfaces for the TIPC stack, from Richard
Alpe.
4) Remove unnecessary looping during ipv6 routing lookups, from Martin
KaFai Lau.
5) Add PAUSE frame generation support to gianfar driver, from Matei
Pavaluca.
6) Allow for larger reordering levels in TCP, which are easily
achievable in the real world right now, from Eric Dumazet.
7) Add a variable of napi_schedule that doesn't need to disable cpu
interrupts, from Eric Dumazet.
8) Use a doubly linked list to optimize neigh_parms_release(), from
Nicolas Dichtel.
9) Various enhancements to the kernel BPF verifier, and allow eBPF
programs to actually be attached to sockets. From Alexei
Starovoitov.
10) Support TSO/LSO in sunvnet driver, from David L Stevens.
11) Allow controlling ECN usage via routing metrics, from Florian
Westphal.
12) Remote checksum offload, from Tom Herbert.
13) Add split-header receive, BQL, and xmit_more support to amd-xgbe
driver, from Thomas Lendacky.
14) Add MPLS support to openvswitch, from Simon Horman.
15) Support wildcard tunnel endpoints in ipv6 tunnels, from Steffen
Klassert.
16) Do gro flushes on a per-device basis using a timer, from Eric
Dumazet. This tries to resolve the conflicting goals between the
desired handling of bulk vs. RPC-like traffic.
17) Allow userspace to ask for the CPU upon what a packet was
received/steered, via SO_INCOMING_CPU. From Eric Dumazet.
18) Limit GSO packets to half the current congestion window, from Eric
Dumazet.
19) Add a generic helper so that all drivers set their RSS keys in a
consistent way, from Eric Dumazet.
20) Add xmit_more support to enic driver, from Govindarajulu
Varadarajan.
21) Add VLAN packet scheduler action, from Jiri Pirko.
22) Support configurable RSS hash functions via ethtool, from Eyal
Perry.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1820 commits)
Fix race condition between vxlan_sock_add and vxlan_sock_release
net/macb: fix compilation warning for print_hex_dump() called with skb->mac_header
net/mlx4: Add support for A0 steering
net/mlx4: Refactor QUERY_PORT
net/mlx4_core: Add explicit error message when rule doesn't meet configuration
net/mlx4: Add A0 hybrid steering
net/mlx4: Add mlx4_bitmap zone allocator
net/mlx4: Add a check if there are too many reserved QPs
net/mlx4: Change QP allocation scheme
net/mlx4_core: Use tasklet for user-space CQ completion events
net/mlx4_core: Mask out host side virtualization features for guests
net/mlx4_en: Set csum level for encapsulated packets
be2net: Export tunnel offloads only when a VxLAN tunnel is created
gianfar: Fix dma check map error when DMA_API_DEBUG is enabled
cxgb4/csiostor: Don't use MASTER_MUST for fw_hello call
net: fec: only enable mdio interrupt before phy device link up
net: fec: clear all interrupt events to support i.MX6SX
net: fec: reset fep link status in suspend function
net: sock: fix access via invalid file descriptor
net: introduce helper macro for_each_cmsghdr
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJUhj6JAAoJEILEb/54YlRxTM4P/j5g5SfqvY0QKsn7sR7MGZ6v
nsgCBhJAqTw3ocNC7EAs8z9h2GWy1KbKpakKYWAh9Fs1yZoey7tFSlcv/Rgjlp70
uU5sDQHtpE9mHKiymdsowiQuWgpl962L4k+k8hUslhlvgk1PvVbpajR6OqG8G+pD
asuIW9eh1APNkLyXmRJ3ZPomzs0VmRdZJ0NEs0lKX9mJskqEvxPIwdaxq3iaJq9B
Fo0J345zUDcJnxWblDRdHlOigCimglElfN5qJwaC4KpwUKuBvLRKbp4f69+wfT0c
kYFiR29X5KjJ2kLfP/wKsLyuDCYYXRq3tCia5M1tAqOjZ+UA89H/GDftx/5lntmv
qUlBa35VfdS1SX4HyApZitOHiLgo+It/hl8Z9bJnhyVw66NxmMQ8JYN2imb8Lhqh
XCLR7BxLTah82AapLJuQ0ZDHPzZqMPG2veC2vAzRMYzVijict/p4Y2+qBqONltER
4rs9uRVn+hamX33lCLg8BEN8zqlnT3rJFIgGaKjq/wXHAU/zpE9CjOrKMQcAg9+s
t51XMNPwypHMAYyGVhEL89ImjXnXxBkLRuquhlmEpvQchIhR+mR3dLsarGn7da44
WPIQJXzcsojXczcwwfqsJCR4I1FTFyQIW+UNh02GkDRgRovQqo+Jk762U7vQwqH+
LBdhvVaS1VW4v+FWXEoZ
=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
As it is, default ->i_fop has NULL ->open() (along with all other methods).
The only case where it matters is reopening (via procfs symlink) a file that
didn't get its ->f_op from ->i_fop - anything else will have ->i_fop assigned
to something sane (default would fail on read/write/ioctl/etc.).
Unfortunately, such case exists - alloc_file() users, especially
anon_get_file() ones. There we have tons of opened files of very different
kinds sharing the same inode. As the result, attempt to reopen those via
procfs succeeds and you get a descriptor you can't do anything with.
Moreover, in case of sockets we set ->i_fop that will only be used
on such reopen attempts - and put a failing ->open() into it to make sure
those do not succeed.
It would be simpler to put such ->open() into default ->i_fop and leave
it unchanged both for anon inode (as we do anyway) and for socket ones. Result:
* everything going through do_dentry_open() works as it used to
* sock_no_open() kludge is gone
* attempts to reopen anon-inode files fail as they really ought to
* ditto for aio_private_file()
* ditto for perfmon - this one actually tried to imitate sock_no_open()
trick, but failed to set ->i_fop, so in the current tree reopens succeed and
yield completely useless descriptor. Intent clearly had been to fail with
-ENXIO on such reopens; now it actually does.
* everything else that used alloc_file() keeps working - it has ->i_fop
set for its inodes anyway
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This patch replaces calls to get_unused_fd() with equivalent call to
get_unused_fd_flags(0) to preserve current behavor for existing code.
In a further patch, get_unused_fd() will be removed so that new code start
using get_unused_fd_flags(), with the hope O_CLOEXEC could be used, either
by default or choosen by userspace.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As there are now no remaining users of arch_fast_hash(), lets kill
it entirely.
This basically reverts commit 71ae8aac3e ("lib: introduce arch
optimized hash library") and follow-up work, that is f.e., commit
237217546d ("lib: hash: follow-up fixups for arch hash"),
commit e3fec2f74f ("lib: Add missing arch generic-y entries for
asm-generic/hash.h") and last but not least commit 6a02652df5
("perf tools: Fix include for non x86 architectures").
Cc: Francesco Fusco <fusco@ntop.org>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 MPX support from Thomas Gleixner:
"This enables support for x86 MPX.
MPX is a new debug feature for bound checking in user space. It
requires kernel support to handle the bound tables and decode the
bound violating instruction in the trap handler"
* 'x86-mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
asm-generic: Remove asm-generic arch_bprm_mm_init()
mm: Make arch_unmap()/bprm_mm_init() available to all architectures
x86: Cleanly separate use of asm-generic/mm_hooks.h
x86 mpx: Change return type of get_reg_offset()
fs: Do not include mpx.h in exec.c
x86, mpx: Add documentation on Intel MPX
x86, mpx: Cleanup unused bound tables
x86, mpx: On-demand kernel allocation of bounds tables
x86, mpx: Decode MPX instruction to get bound violation information
x86, mpx: Add MPX-specific mmap interface
x86, mpx: Introduce VM_MPX to indicate that a VMA is MPX specific
x86, mpx: Add MPX to disabled features
ia64: Sync struct siginfo with general version
mips: Sync struct siginfo with general version
mpx: Extend siginfo structure to include bound violation information
x86, mpx: Rename cfg_reg_u and status_reg
x86: mpx: Give bndX registers actual names
x86: Remove arbitrary instruction size limit in instruction decoder
Pull irq domain updates from Thomas Gleixner:
"The real interesting irq updates:
- Support for hierarchical irq domains:
For complex interrupt routing scenarios where more than one
interrupt related chip is involved we had no proper representation
in the generic interrupt infrastructure so far. That made people
implement rather ugly constructs in their nested irq chip
implementations. The main offenders are x86 and arm/gic.
To distangle that mess we have now hierarchical irqdomains which
seperate the various interrupt chips and connect them via the
hierarchical domains. That keeps the domain specific details
internal to the particular hierarchy level and removes the
criss/cross referencing of chip internals. The resulting hierarchy
for a complex x86 system will look like this:
vector mapped: 74
msi-0 mapped: 2
dmar-ir-1 mapped: 69
ioapic-1 mapped: 4
ioapic-0 mapped: 20
pci-msi-2 mapped: 45
dmar-ir-0 mapped: 3
ioapic-2 mapped: 1
pci-msi-1 mapped: 2
htirq mapped: 0
Neither ioapic nor pci-msi know about the dmar interrupt remapping
between themself and the vector domain. If interrupt remapping is
disabled ioapic and pci-msi become direct childs of the vector
domain.
In hindsight we should have done that years ago, but in hindsight
we always know better :)
- Support for generic MSI interrupt domain handling
We have more and more non PCI related MSI interrupts, so providing
a generic infrastructure for this is better than having all
affected architectures implementing their own private hacks.
- Support for PCI-MSI interrupt domain handling, based on the generic
MSI support.
This part carries the pci/msi branch from Bjorn Helgaas pci tree to
avoid a massive conflict. The PCI/MSI parts are acked by Bjorn.
I have two more branches on top of this. The full conversion of x86
to hierarchical domains and a partial conversion of arm/gic"
* 'irq-irqdomain-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (41 commits)
genirq: Move irq_chip_write_msi_msg() helper to core
PCI/MSI: Allow an msi_controller to be associated to an irq domain
PCI/MSI: Provide mechanism to alloc/free MSI/MSIX interrupt from irqdomain
PCI/MSI: Enhance core to support hierarchy irqdomain
PCI/MSI: Move cached entry functions to irq core
genirq: Provide default callbacks for msi_domain_ops
genirq: Introduce msi_domain_alloc/free_irqs()
asm-generic: Add msi.h
genirq: Add generic msi irq domain support
genirq: Introduce callback irq_chip.irq_write_msi_msg
genirq: Work around __irq_set_handler vs stacked domains ordering issues
irqdomain: Introduce helper function irq_domain_add_hierarchy()
irqdomain: Implement a method to automatically call parent domains alloc/free
genirq: Introduce helper irq_domain_set_info() to reduce duplicated code
genirq: Split out flow handler typedefs into seperate header file
genirq: Add IRQ_SET_MASK_OK_DONE to support stacked irqchip
genirq: Introduce irq_chip.irq_compose_msi_msg() to support stacked irqchip
genirq: Add more helper functions to support stacked irq_chip
genirq: Introduce helper functions to support stacked irq_chip
irqdomain: Do irq_find_mapping and set_type for hierarchy irqdomain in case OF
...
While there normally is no reason to have a pull request for asm-generic
but have all changes get merged through whichever tree needs them, I do
have a series for 3.19. There are two sets of patches that change
significant portions of asm/io.h, and this branch contains both in order
to resolve the conflicts:
- Will Deacon has done a set of patches to ensure that all architectures
define {read,write}{b,w,l,q}_relaxed() functions or get them by
including asm-generic/io.h. These functions are commonly used on ARM
specific drivers to avoid expensive L2 cache synchronization implied by
the normal {read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures and
to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xUv6
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic asm/io.h rewrite from Arnd Bergmann:
"While there normally is no reason to have a pull request for
asm-generic but have all changes get merged through whichever tree
needs them, I do have a series for 3.19.
There are two sets of patches that change significant portions of
asm/io.h, and this branch contains both in order to resolve the
conflicts:
- Will Deacon has done a set of patches to ensure that all
architectures define {read,write}{b,w,l,q}_relaxed() functions or
get them by including asm-generic/io.h.
These functions are commonly used on ARM specific drivers to avoid
expensive L2 cache synchronization implied by the normal
{read,write}{b,w,l,q}, but we need to define them on all
architectures in order to share the drivers across architectures
and to enable CONFIG_COMPILE_TEST configurations for them
- Thierry Reding has done an unrelated set of patches that extends
the asm-generic/io.h file to the degree necessary to make it useful
on ARM64 and potentially other architectures"
* tag 'asm-generic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (29 commits)
ARM64: use GENERIC_PCI_IOMAP
sparc: io: remove duplicate relaxed accessors on sparc32
ARM: sa11x0: Use void __iomem * in MMIO accessors
arm64: Use include/asm-generic/io.h
ARM: Use include/asm-generic/io.h
asm-generic/io.h: Implement generic {read,write}s*()
asm-generic/io.h: Reconcile I/O accessor overrides
/dev/mem: Use more consistent data types
Change xlate_dev_{kmem,mem}_ptr() prototypes
ARM: ixp4xx: Properly override I/O accessors
ARM: ixp4xx: Fix build with IXP4XX_INDIRECT_PCI
ARM: ebsa110: Properly override I/O accessors
ARC: Remove redundant PCI_IOBASE declaration
documentation: memory-barriers: clarify relaxed io accessor semantics
x86: io: implement dummy relaxed accessor macros for writes
tile: io: implement dummy relaxed accessor macros for writes
sparc: io: implement dummy relaxed accessor macros for writes
powerpc: io: implement dummy relaxed accessor macros for writes
parisc: io: implement dummy relaxed accessor macros for writes
mn10300: io: implement dummy relaxed accessor macros for writes
...
introduce new setsockopt() command:
setsockopt(sock, SOL_SOCKET, SO_ATTACH_BPF, &prog_fd, sizeof(prog_fd))
where prog_fd was received from syscall bpf(BPF_PROG_LOAD, attr, ...)
and attr->prog_type == BPF_PROG_TYPE_SOCKET_FILTER
setsockopt() calls bpf_prog_get() which increments refcnt of the program,
so it doesn't get unloaded while socket is using the program.
The same eBPF program can be attached to multiple sockets.
User task exit automatically closes socket which calls sk_filter_uncharge()
which decrements refcnt of eBPF program
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not valid to select CONFIG_PM directly without selecting
CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME too, because that breaks
dependencies (ia64 does that) and it is not necessary to select
CONFIG_PM directly if CONFIG_PM_SLEEP or CONFIG_PM_RUNTIME is
selected, because CONFIG_PM will be set automatically in that
case (sh does that).
Fix those mistakes.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__get_cpu_var was removed. Update the comments.
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This reverts commit 85c8555ff0 ("KVM: check for !is_zero_pfn() in
kvm_is_mmio_pfn()") and renames the function to kvm_is_reserved_pfn.
The problem being addressed by the patch above was that some ARM code
based the memory mapping attributes of a pfn on the return value of
kvm_is_mmio_pfn(), whose name indeed suggests that such pfns should
be mapped as device memory.
However, kvm_is_mmio_pfn() doesn't do quite what it says on the tin,
and the existing non-ARM users were already using it in a way which
suggests that its name should probably have been 'kvm_is_reserved_pfn'
from the beginning, e.g., whether or not to call get_page/put_page on
it etc. This means that returning false for the zero page is a mistake
and the patch above should be reverted.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The PCI/MSI irq chip callbacks mask/unmask_msi_irq have been renamed
to pci_msi_mask/unmask_irq to mark them PCI specific. Rename all usage
sites. The conversion helper functions are kept around to avoid
conflicts in next and will be removed after merging into mainline.
Coccinelle assisted conversion. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: x86@kernel.org
Cc: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Simon Horman <horms@verge.net.au>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Rename write_msi_msg() to pci_write_msi_msg() to mark it as PCI
specific.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
KVM for ia64 has been marked as broken not just once, but twice even,
and the last patch from the maintainer is now roughly 5 years old.
Time for it to rest in peace.
Acked-by: Gleb Natapov <gleb@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
New fields about bound violation are added into general struct
siginfo. This will impact MIPS and IA64, which extend general
struct siginfo. This patch syncs this struct for IA64 with
general version.
Signed-off-by: Qiaowei Ren <qiaowei.ren@intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: linux-mm@kvack.org
Cc: linux-mips@linux-mips.org
Cc: Dave Hansen <dave@sr71.net>
Link: http://lkml.kernel.org/r/20141114151822.82B3B486@viggo.jf.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The IA64_HP_SIM dependency on PM_RUNTIME should be done in the arch
Kconfig instead of in the PM core. Move it accordingly.
NOTE: arch/ia64/Kconfig currently does a 'select PM', which since
commit 1eb208aea3 (PM: Make CONFIG_PM depend on (CONFIG_PM_SLEEP ||
CONFIG_PM_RUNTIME)) is effectively a noop unless PM_SLEEP or
PM_RUNTIME are set elsewhere.
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Alternative to RPS/RFS is to use hardware support for multiple
queues.
Then split a set of million of sockets into worker threads, each
one using epoll() to manage events on its own socket pool.
Ideally, we want one thread per RX/TX queue/cpu, but we have no way to
know after accept() or connect() on which queue/cpu a socket is managed.
We normally use one cpu per RX queue (IRQ smp_affinity being properly
set), so remembering on socket structure which cpu delivered last packet
is enough to solve the problem.
After accept(), connect(), or even file descriptor passing around
processes, applications can use :
int cpu;
socklen_t len = sizeof(cpu);
getsockopt(fd, SOL_SOCKET, SO_INCOMING_CPU, &cpu, &len);
And use this information to put the socket into the right silo
for optimal performance, as all networking stack should run
on the appropriate cpu, without need to send IPI (RPS/RFS).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xlate_dev_mem_ptr() is used to convert a physical address to an uncached
kernel virtual address mapping, so make it use phys_addr_t as type for
the physical address and return void * for the kernel virtual address.
xlate_dev_kmem_ptr() converts a cached kernel virtual address mapping to
an uncached kernel virtual address mapping, so make it use void * for
both the input parameter and return value.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Pull x86 EFI updates from Peter Anvin:
"This patchset falls under the "maintainers that grovel" clause in the
v3.18-rc1 announcement. We had intended to push it late in the merge
window since we got it into the -tip tree relatively late.
Many of these are relatively simple things, but there are a couple of
key bits, especially Ard's and Matt's patches"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
rtc: Disable EFI rtc for x86
efi: rtc-efi: Export platform:rtc-efi as module alias
efi: Delete the in_nmi() conditional runtime locking
efi: Provide a non-blocking SetVariable() operation
x86/efi: Adding efi_printks on memory allocationa and pci.reads
x86/efi: Mark initialization code as such
x86/efi: Update comment regarding required phys mapped EFI services
x86/efi: Unexport add_efi_memmap variable
x86/efi: Remove unused efi_call* macros
efi: Resolve some shadow warnings
arm64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
ia64: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
x86: efi: Format EFI memory type & attrs with efi_md_typeattr_format()
efi: Introduce efi_md_typeattr_format()
efi: Add macro for EFI_MEMORY_UCE memory attribute
x86/efi: Clear EFI_RUNTIME_SERVICES if failing to enter virtual mode
arm64/efi: Do not enter virtual mode if booting with efi=noruntime or noefi
arm64/efi: uefi_init error handling fix
efi: Add kernel param efi=noruntime
lib: Add a generic cmdline parse function parse_option_str
...
write{b,w,l,q}_relaxed are implemented by some architectures in order to
permit memory-mapped I/O accesses with weaker barrier semantics than the
non-relaxed variants.
This patch adds dummy macros for the write accessors to ia64, which may
be able to be optimised in a similar manner to the relaxed read
accessors at a later date.
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Pull audit updates from Eric Paris:
"So this change across a whole bunch of arches really solves one basic
problem. We want to audit when seccomp is killing a process. seccomp
hooks in before the audit syscall entry code. audit_syscall_entry
took as an argument the arch of the given syscall. Since the arch is
part of what makes a syscall number meaningful it's an important part
of the record, but it isn't available when seccomp shoots the
syscall...
For most arch's we have a better way to get the arch (syscall_get_arch)
So the solution was two fold: Implement syscall_get_arch() everywhere
there is audit which didn't have it. Use syscall_get_arch() in the
seccomp audit code. Having syscall_get_arch() everywhere meant it was
a useless flag on the stack and we could get rid of it for the typical
syscall entry.
The other changes inside the audit system aren't grand, fixed some
records that had invalid spaces. Better locking around the task comm
field. Removing some dead functions and structs. Make some things
static. Really minor stuff"
* git://git.infradead.org/users/eparis/audit: (31 commits)
audit: rename audit_log_remove_rule to disambiguate for trees
audit: cull redundancy in audit_rule_change
audit: WARN if audit_rule_change called illegally
audit: put rule existence check in canonical order
next: openrisc: Fix build
audit: get comm using lock to avoid race in string printing
audit: remove open_arg() function that is never used
audit: correct AUDIT_GET_FEATURE return message type
audit: set nlmsg_len for multicast messages.
audit: use union for audit_field values since they are mutually exclusive
audit: invalid op= values for rules
audit: use atomic_t to simplify audit_serial()
kernel/audit.c: use ARRAY_SIZE instead of sizeof/sizeof[0]
audit: reduce scope of audit_log_fcaps
audit: reduce scope of audit_net_id
audit: arm64: Remove the audit arch argument to audit_syscall_entry
arm64: audit: Add audit hook in syscall_trace_enter/exit()
audit: x86: drop arch from __audit_syscall_entry() interface
sparc: implement is_32bit_task
sparc: properly conditionalize use of TIF_32BIT
...
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
Merge second patch-bomb from Andrew Morton:
- a few hotfixes
- drivers/dma updates
- MAINTAINERS updates
- Quite a lot of lib/ updates
- checkpatch updates
- binfmt updates
- autofs4
- drivers/rtc/
- various small tweaks to less used filesystems
- ipc/ updates
- kernel/watchdog.c changes
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (135 commits)
mm: softdirty: enable write notifications on VMAs after VM_SOFTDIRTY cleared
kernel/param: consolidate __{start,stop}___param[] in <linux/moduleparam.h>
ia64: remove duplicate declarations of __per_cpu_start[] and __per_cpu_end[]
frv: remove unused declarations of __start___ex_table and __stop___ex_table
kvm: ensure hard lockup detection is disabled by default
kernel/watchdog.c: control hard lockup detection default
staging: rtl8192u: use %*pEn to escape buffer
staging: rtl8192e: use %*pEn to escape buffer
staging: wlan-ng: use %*pEhp to print SN
lib80211: remove unused print_ssid()
wireless: hostap: proc: print properly escaped SSID
wireless: ipw2x00: print SSID via %*pE
wireless: libertas: print esaped string via %*pE
lib/vsprintf: add %*pE[achnops] format specifier
lib / string_helpers: introduce string_escape_mem()
lib / string_helpers: refactoring the test suite
lib / string_helpers: move documentation to c-file
include/linux: remove strict_strto* definitions
arch/x86/mm/numa.c: fix boot failure when all nodes are hotpluggable
fs: check bh blocknr earlier when searching lru
...
Pull scheduler updates from Ingo Molnar:
"The main changes in this cycle were:
- Optimized support for Intel "Cluster-on-Die" (CoD) topologies (Dave
Hansen)
- Various sched/idle refinements for better idle handling (Nicolas
Pitre, Daniel Lezcano, Chuansheng Liu, Vincent Guittot)
- sched/numa updates and optimizations (Rik van Riel)
- sysbench speedup (Vincent Guittot)
- capacity calculation cleanups/refactoring (Vincent Guittot)
- Various cleanups to thread group iteration (Oleg Nesterov)
- Double-rq-lock removal optimization and various refactorings
(Kirill Tkhai)
- various sched/deadline fixes
... and lots of other changes"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (72 commits)
sched/dl: Use dl_bw_of() under rcu_read_lock_sched()
sched/fair: Delete resched_cpu() from idle_balance()
sched, time: Fix build error with 64 bit cputime_t on 32 bit systems
sched: Improve sysbench performance by fixing spurious active migration
sched/x86: Fix up typo in topology detection
x86, sched: Add new topology for multi-NUMA-node CPUs
sched/rt: Use resched_curr() in task_tick_rt()
sched: Use rq->rd in sched_setaffinity() under RCU read lock
sched: cleanup: Rename 'out_unlock' to 'out_free_new_mask'
sched: Use dl_bw_of() under RCU read lock
sched/fair: Remove duplicate code from can_migrate_task()
sched, mips, ia64: Remove __ARCH_WANT_UNLOCKED_CTXSW
sched: print_rq(): Don't use tasklist_lock
sched: normalize_rt_tasks(): Don't use _irqsave for tasklist_lock, use task_rq_lock()
sched: Fix the task-group check in tg_has_rt_tasks()
sched/fair: Leverage the idle state info when choosing the "idlest" cpu
sched: Let the scheduler see CPU idle states
sched/deadline: Fix inter- exclusive cpusets migrations
sched/deadline: Clear dl_entity params when setscheduling to different class
sched/numa: Kill the wrong/dead TASK_DEAD check in task_numa_fault()
...
Pull arch atomic cleanups from Ingo Molnar:
"This is a series kept separate from the main locking tree, which
cleans up and improves various details in the atomics type handling:
- Remove the unused atomic_or_long() method
- Consolidate and compress atomic ops implementations between
architectures, to reduce linecount and to make it easier to add new
ops.
- Rewrite generic atomic support to only require cmpxchg() from an
architecture - generate all other methods from that"
* 'locking-arch-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
locking,arch: Use ACCESS_ONCE() instead of cast to volatile in atomic_read()
locking, mips: Fix atomics
locking, sparc64: Fix atomics
locking,arch: Rewrite generic atomic support
locking,arch,xtensa: Fold atomic_ops
locking,arch,sparc: Fold atomic_ops
locking,arch,sh: Fold atomic_ops
locking,arch,powerpc: Fold atomic_ops
locking,arch,parisc: Fold atomic_ops
locking,arch,mn10300: Fold atomic_ops
locking,arch,mips: Fold atomic_ops
locking,arch,metag: Fold atomic_ops
locking,arch,m68k: Fold atomic_ops
locking,arch,m32r: Fold atomic_ops
locking,arch,ia64: Fold atomic_ops
locking,arch,hexagon: Fold atomic_ops
locking,arch,cris: Fold atomic_ops
locking,arch,avr32: Fold atomic_ops
locking,arch,arm64: Fold atomic_ops
locking,arch,arm: Fold atomic_ops
...
Pull timer fixes from Ingo Molnar:
"Main changes:
- Fix the deadlock reported by Dave Jones et al
- Clean up and fix nohz_full interaction with arch abilities
- nohz init code consolidation/cleanup"
* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
nohz: nohz full depends on irq work self IPI support
nohz: Consolidate nohz full init code
arm64: Tell irq work about self IPI support
arm: Tell irq work about self IPI support
x86: Tell irq work about self IPI support
irq_work: Force raised irq work to run on irq work interrupt
irq_work: Introduce arch_irq_work_has_interrupt()
nohz: Move nohz full init call to tick init
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest and
via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put firmware
in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization improvements
(including improved Windows support on Intel and Jailhouse hypervisor
support on AMD), adaptive PLE which helps overcommitting of huge guests.
Also included are some patches that make KVM more friendly to memory
hot-unplug, and fixes for rare caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes. To verify
future signed pull requests from me, please update my key with
"gpg --recv-keys 9B4D86F2". You should see 3 new subkeys---the
one for signing will be a 2048-bit RSA key, 4E6B09D7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=iEVi
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Fixes and features for 3.18.
Apart from the usual cleanups, here is the summary of new features:
- s390 moves closer towards host large page support
- PowerPC has improved support for debugging (both inside the guest
and via gdbstub) and support for e6500 processors
- ARM/ARM64 support read-only memory (which is necessary to put
firmware in emulated NOR flash)
- x86 has the usual emulator fixes and nested virtualization
improvements (including improved Windows support on Intel and
Jailhouse hypervisor support on AMD), adaptive PLE which helps
overcommitting of huge guests. Also included are some patches that
make KVM more friendly to memory hot-unplug, and fixes for rare
caching bugs.
Two patches have trivial mm/ parts that were acked by Rik and Andrew.
Note: I will soon switch to a subkey for signing purposes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (157 commits)
kvm: do not handle APIC access page if in-kernel irqchip is not in use
KVM: s390: count vcpu wakeups in stat.halt_wakeup
KVM: s390/facilities: allow TOD-CLOCK steering facility bit
KVM: PPC: BOOK3S: HV: CMA: Reserve cma region only in hypervisor mode
arm/arm64: KVM: Report correct FSC for unsupported fault types
arm/arm64: KVM: Fix VTTBR_BADDR_MASK and pgd alloc
kvm: Fix kvm_get_page_retry_io __gup retval check
arm/arm64: KVM: Fix set_clear_sgi_pend_reg offset
kvm: x86: Unpin and remove kvm_arch->apic_access_page
kvm: vmx: Implement set_apic_access_page_addr
kvm: x86: Add request bit to reload APIC access page address
kvm: Add arch specific mmu notifier for page invalidation
kvm: Rename make_all_cpus_request() to kvm_make_all_cpus_request() and make it non-static
kvm: Fix page ageing bugs
kvm/x86/mmu: Pass gfn and level to rmapp callback.
x86: kvm: use alternatives for VMCALL vs. VMMCALL if kernel text is read-only
kvm: x86: use macros to compute bank MSRs
KVM: x86: Remove debug assertion of non-PAE reserved bits
kvm: don't take vcpu mutex for obviously invalid vcpu ioctls
kvm: Faults which trigger IO release the mmap_sem
...
The effects of the patch on the i64 memory map log are similar to those
visible in the previous (x86) patch: the type enum and the attribute
bitmap are decoded.
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Use the much more reader friendly ACCESS_ONCE() instead of the cast to volatile.
This is purely a stylistic change.
Signed-off-by: Pranith Kumar <bobby.prani@gmail.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-arch@vger.kernel.org
Link: http://lkml.kernel.org/r/1411482607-20948-1-git-send-email-bobby.prani@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Both callers of get_cached_msi_msg() start with a struct irq_data pointer,
look up the corresponding IRQ number, and pass it to get_cached_msi_msg(),
which then uses irq_get_irq_data() to look up the struct irq_data again to
call __get_cached_msi_msg().
Since we already have the struct irq_data, call __get_cached_msi_msg()
directly and skip the lookup work done by get_cached_msi_msg().
No functional change.
[bhelgaas: changelog]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Tony Luck <tony.luck@intel.com>
CC: linux-ia64@vger.kernel.org
Prompted by a change to drivers/scsi/Kconfig which used to do a
"select NET" but now does a "depends on NET". This meant that some
configurations ended up without CONFIG_NET=y
Signed-off-by Tony Luck <tony.luck@intel.com>
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUG7o9AAoJEFmIoMA60/r8hbYP/3gR3xHd2QKpkmBcM1lf1yiR
osQQnAfRqEO4fzrpmOYrYbLIAOPwanK6Y36rmIYB+wHU2SUaffV7ZI9uW32shTud
09+1N+OrSS6fwzVUWOuKsf1kv/jxpS+ic2fb+Qe1OXwJh5G+z1D9Kvd2EPLJdlgK
ySyX4zSTrLni8CoclzREO7u82VVO5rTdvbujBxuvpOQTOdD5TFqV/uhb/y3gQz+u
sG6IxUbdXsy4r24C6OnPrmmZ1Rk/lgCMyA+QSozc5Eu5PdGzcY9a6gcKlTnsbwBs
qYLAb+/KCa3KgQh07NYmFfYdpoMZUXgSsEtD8gyvfJQHwUYwW8rsEMKxlSCQrzYr
0OrpBSVTO6ta1r8SKOWtSYETQgPE3GUiJR1DuCyV+55RLZYp6Q8zH6dbgfWQbA/g
R/kWHihR/tcD9YIlT99QrBppZtvG5nZ3y7aLSqdYYxEJqHE0tlbuxAu8hgwDf3Qp
lKZJMyadLB1MS9lnrMj8DYqIOKbe62LOwcEYzhMJzaq8vCy+JWtjxOOgwBkT7P5v
bhhYh3eqi5/MBONtw52V6RDUQId9vOLGHoiM5/akG4FFmWdhO9S0SbMBhAJyazKT
n3IP5yj657XAi/fK939PUCQ3YuT5GqlCNcXDCqUzBZhGnt/Ln7LPmQI323519Lp4
3vI3irFT0Fu2IFEBhc6l
=xIYe
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These fix:
- Boot video device detection on dual-GPU Apple systems
- Hotplug fiascos on VGA switcheroo with radeon & nouveau drivers
- Boot hang on Freescale i.MX6 systems
- Excessive "no hotplug settings from platform" warnings
In particular:
Enumeration
- Don't default exclusively to first video device (Bruno Prémont)
PCI device hotplug
- Remove "no hotplug settings from platform" warning (Bjorn Helgaas)
- Add pci_ignore_hotplug() for VGA switcheroo (Bjorn Helgaas)
Freescale i.MX6
- Put LTSSM in "Detect" state before disabling (Lucas Stach)"
* tag 'pci-v3.17-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
vgaarb: Drop obsolete #ifndef
vgaarb: Don't default exclusively to first video device with mem+io
ACPIPHP / radeon / nouveau: Remove acpi_bus_no_hotplug()
PCI: Remove "no hotplug settings from platform" warning
PCI: Add pci_ignore_hotplug() to ignore hotplug events for a device
PCI: imx6: Put LTSSM in "Detect" state before disabling it
MAINTAINERS: Add Lucas Stach as co-maintainer for i.MX6 PCI driver
Commit 20cde69402 ("x86, ia64: Move EFI_FB vga_default_device()
initialization to pci_vga_fixup()") moved boot video device detection from
efifb to x86 and ia64 pci/fixup.c.
For dual-GPU Apple computers above change represents a regression as code
in efifb did forcefully override vga_default_device while the merge did not
(vgaarb happens prior to PCI fixup).
To improve on initial device selection by vgaarb (it cannot know if PCI
device not behind bridges see/decode legacy VGA I/O or not), move the
screen_info based check from pci_video_fixup() to vgaarb's init function and
use it to refine/override decision taken while adding the individual PCI
VGA devices. This way PCI fixup has no reason to adjust vga_default_device
anymore but can depend on its value for flagging shadowed VBIOS.
This has the nice benefit of removing duplicated code but does introduce a
#if defined() block in vgaarb. Not all architectures have screen_info and
would cause compile to fail without it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=84461
Reported-and-Tested-By: Andreas Noever <andreas.noever@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
Cut & paste typo from the line above.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The nohz full code needs irq work to trigger its own interrupt so that
the subsystem can work even when the tick is stopped.
Lets introduce arch_irq_work_has_interrupt() that archs can override to
tell about their support for this ability.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
There must be an explit statement to modify the percpu variable after
the conversion of the sn_nodpda macro to use this_cpu_read.
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Compile-tested-by: Guenter Roeck <linux@roeck-us.net>
New system call depends on crypto. As it did not have a separate config
option, CONFIG_KEXEC was modified to select CRYPTO and CRYPTO_SHA256.
But now previous patch introduced a new config option for new syscall.
So CONFIG_KEXEC does not require crypto. Remove that dependency.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In the beggining was on_each_cpu(), which required an unused argument to
kvm_arch_ops.hardware_{en,dis}able, but this was soon forgotten.
Remove unnecessary arguments that stem from this.
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Using static inline is going to save few bytes and cycles.
For example on powerpc, the difference is 700 B after stripping.
(5 kB before)
This patch also deals with two overlooked empty functions:
kvm_arch_flush_shadow was not removed from arch/mips/kvm/mips.c
2df72e9bc KVM: split kvm_arch_flush_shadow
and kvm_arch_sched_in never made it into arch/ia64/kvm/kvm-ia64.c.
e790d9ef6 KVM: add kvm_arch_sched_in
Signed-off-by: Radim KrÄmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Opaque KVM structs are useful for prototypes in asm/kvm_host.h, to avoid
"'struct foo' declared inside parameter list" warnings (and consequent
breakage due to conflicting types).
Move them from individual files to a generic place in linux/kvm_types.h.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.
The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e. using a global
register that may be set to the per cpu base.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull kbuild updates from Michal Marek:
- make clean also considers $(extra-m) and $(extra-) to be consistent
- cleanup and fixes in scripts/Makefile.host
- allow to override the name of the Python 2 executable with make
PYTHON=... (only needed for ia64 in practice)
- option to split debugingo into *.dwo files to save disk space if the
compiler supports it (CONFIG_DEBUG_INFO_SPLIT)
- option to use dwarf4 debuginfo if the compiler supports it
(CONFIG_DEBUG_INFO_DWARF4)
- fix for disabling certain warnings with clang
- fix for unneeded rebuild with dash when a command contains
backslashes
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kbuild: Fix handling of backslashes in *.cmd files
kbuild, LLVMLinux: Supress warnings unless W=1-3
Kbuild: Add a option to enable dwarf4 v2
kbuild: Support split debug info v4
kbuild: allow to override Python command name
kbuild: clean-up and bug fix of scripts/Makefile.host
kbuild: clean up scripts/Makefile.host
kbuild: drop shared library support from Makefile.host
kbuild: fix a bug of C++ host program handling
kbuild: fix a typo in scripts/Makefile.host
scripts/Makefile.clean: clean also $(extra-m) and $(extra-)
Many of the atomic op implementations are the same except for one
instruction; fold the lot into a few CPP macros and reduce LoC.
This also prepares for easy addition of new ops.
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-ia64@vger.kernel.org
Link: http://lkml.kernel.org/r/20140508135852.245224472@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull arch signal handling cleanup from Richard Weinberger:
"This patch series moves all remaining archs to the get_signal(),
signal_setup_done() and sigsp() functions.
Currently these archs use open coded variants of the said functions.
Further, unused parameters get removed from get_signal_to_deliver(),
tracehook_signal_handler() and signal_delivered().
At the end of the day we save around 500 lines of code."
* 'signal-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/misc: (43 commits)
powerpc: Use sigsp()
openrisc: Use sigsp()
mn10300: Use sigsp()
mips: Use sigsp()
microblaze: Use sigsp()
metag: Use sigsp()
m68k: Use sigsp()
m32r: Use sigsp()
hexagon: Use sigsp()
frv: Use sigsp()
cris: Use sigsp()
c6x: Use sigsp()
blackfin: Use sigsp()
avr32: Use sigsp()
arm64: Use sigsp()
arc: Use sigsp()
sas_ss_flags: Remove nested ternary if
Rip out get_signal_to_deliver()
Clean up signal_delivered()
tracehook_signal_handler: Remove sig, info, ka and regs
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zjzv
-----END PGP SIGNATURE-----
Merge tag 'please-pull-getrandom' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 system call update from Tony Luck:
"Wire up getrandom system call for ia64"
* tag 'please-pull-getrandom' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] Wire up getrandom() system call
Merge more incoming from Andrew Morton:
"Two new syscalls:
memfd_create in "shm: add memfd_create() syscall"
kexec_file_load in "kexec: implementation of new syscall kexec_file_load"
And:
- Most (all?) of the rest of MM
- Lots of the usual misc bits
- fs/autofs4
- drivers/rtc
- fs/nilfs
- procfs
- fork.c, exec.c
- more in lib/
- rapidio
- Janitorial work in filesystems: fs/ufs, fs/reiserfs, fs/adfs,
fs/cramfs, fs/romfs, fs/qnx6.
- initrd/initramfs work
- "file sealing" and the memfd_create() syscall, in tmpfs
- add pci_zalloc_consistent, use it in lots of places
- MAINTAINERS maintenance
- kexec feature work"
* emailed patches from Andrew Morton <akpm@linux-foundation.org: (193 commits)
MAINTAINERS: update nomadik patterns
MAINTAINERS: update usb/gadget patterns
MAINTAINERS: update DMA BUFFER SHARING patterns
kexec: verify the signature of signed PE bzImage
kexec: support kexec/kdump on EFI systems
kexec: support for kexec on panic using new system call
kexec-bzImage64: support for loading bzImage using 64bit entry
kexec: load and relocate purgatory at kernel load time
purgatory: core purgatory functionality
purgatory/sha256: provide implementation of sha256 in purgaotory context
kexec: implementation of new syscall kexec_file_load
kexec: new syscall kexec_file_load() declaration
kexec: make kexec_segment user buffer pointer a union
resource: provide new functions to walk through resources
kexec: use common function for kimage_normal_alloc() and kimage_crash_alloc()
kexec: move segment verification code in a separate function
kexec: rename unusebale_pages to unusable_pages
kernel: build bin2c based on config option CONFIG_BUILD_BIN2C
bin2c: move bin2c in scripts/basic
shm: wait for pins to be released when sealing
...
Load purgatory code in RAM and relocate it based on the location.
Relocation code has been inspired by module relocation code and purgatory
relocation code in kexec-tools.
Also compute the checksums of loaded kexec segments and store them in
purgatory.
Arch independent code provides this functionality so that arch dependent
bootloaders can make use of it.
Helper functions are provided to get/set symbol values in purgatory which
are used by bootloaders later to set things like stack and entry point of
second kernel etc.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: WANG Chao <chaowang@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The core mm code will provide a default gate area based on
FIXADDR_USER_START and FIXADDR_USER_END if
!defined(__HAVE_ARCH_GATE_AREA) && defined(AT_SYSINFO_EHDR).
This default is only useful for ia64. arm64, ppc, s390, sh, tile, 64-bit
UML, and x86_32 have their own code just to disable it. arm, 32-bit UML,
and x86_64 have gate areas, but they have their own implementations.
This gets rid of the default and moves the code into ia64.
This should save some code on architectures without a gate area: it's now
possible to inline the gate_area functions in the default case.
Signed-off-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Nathan Lynch <nathan_lynch@mentor.com>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [in principle]
Acked-by: Richard Weinberger <richard@nod.at> [for um]
Acked-by: Will Deacon <will.deacon@arm.com> [for arm64]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Nathan Lynch <Nathan_Lynch@mentor.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Rather than have architectures #define ARCH_HAS_SG_CHAIN in an
architecture specific scatterlist.h, make it a proper Kconfig option and
use that instead. At same time, remove the header files are are now
mostly useless and just include asm-generic/scatterlist.h.
[sfr@canb.auug.org.au: powerpc files now need asm/dma.h]
Signed-off-by: Laura Abbott <lauraa@codeaurora.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de> [x86]
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> [powerpc]
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, the rtc-efi driver is restricted to ia64 only. Newer
architectures with EFI support may want to also use that driver. This
patch moves the platform device setup from ia64 into drivers/rtc and
allow any architecture with CONFIG_EFI=y to use the rtc-efi driver.
Signed-off-by: Mark Salter <msalter@redhat.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
they had small conflicts (respectively within KVM documentation,
and with 3.16-rc changes). Since they were all within the subsystem,
I took care of them.
Stephen Rothwell reported some snags in PPC builds, but they are all
fixed now; the latest linux-next report was clean.
New features for ARM include:
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
And for PPC:
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S HV: Add in-guest debug support
This release drops support for KVM on the PPC440. As a result, the
PPC merge removes more lines than it adds. :)
I also included an x86 change, since Davidlohr tied it to an independent
bug report and the reporter quickly provided a Tested-by; there was no
reason to wait for -rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=hyQP
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second round of KVM changes from Paolo Bonzini:
"Here are the PPC and ARM changes for KVM, which I separated because
they had small conflicts (respectively within KVM documentation, and
with 3.16-rc changes). Since they were all within the subsystem, I
took care of them.
Stephen Rothwell reported some snags in PPC builds, but they are all
fixed now; the latest linux-next report was clean.
New features for ARM include:
- KVM VGIC v2 emulation on GICv3 hardware
- Big-Endian support for arm/arm64 (guest and host)
- Debug Architecture support for arm64 (arm32 is on Christoffer's todo list)
And for PPC:
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S HV: Add in-guest debug support
This release drops support for KVM on the PPC440. As a result, the
PPC merge removes more lines than it adds. :)
I also included an x86 change, since Davidlohr tied it to an
independent bug report and the reporter quickly provided a Tested-by;
there was no reason to wait for -rc2"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (122 commits)
KVM: Move more code under CONFIG_HAVE_KVM_IRQFD
KVM: nVMX: fix "acknowledge interrupt on exit" when APICv is in use
KVM: nVMX: Fix nested vmexit ack intr before load vmcs01
KVM: PPC: Enable IRQFD support for the XICS interrupt controller
KVM: Give IRQFD its own separate enabling Kconfig option
KVM: Move irq notifier implementation into eventfd.c
KVM: Move all accesses to kvm::irq_routing into irqchip.c
KVM: irqchip: Provide and use accessors for irq routing table
KVM: Don't keep reference to irq routing table in irqfd struct
KVM: PPC: drop duplicate tracepoint
arm64: KVM: fix 64bit CP15 VM access for 32bit guests
KVM: arm64: GICv3: mandate page-aligned GICV region
arm64: KVM: GICv3: move system register access to msr_s/mrs_s
KVM: PPC: PR: Handle FSCR feature deselects
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
KVM: PPC: Remove DCR handling
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Handle magic page in kvmppc_ld/st
...
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
- ACPICA update to upstream version 20140724. That includes
ACPI 5.1 material (support for the _CCA and _DSD predefined names,
changes related to the DMAR and PCCT tables and ARM support among
other things) and cleanups related to using ACPICA's header files.
A major part of it is related to acpidump and the core code used
by that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and
Rafael J Wysocki.
- Cleanups and improvements related to system suspend from
Lan Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand
governor and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from
Mikulas Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano,
Sandeep Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas Renninger.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ZODv
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"Again, ACPICA leads the pack (47 commits), followed by cpufreq (18
commits) and system suspend/hibernation (9 commits).
From the new code perspective, the ACPICA update brings ACPI 5.1 to
the table, including a new device configuration object called _DSD
(Device Specific Data) that will hopefully help us to operate device
properties like Device Trees do (at least to some extent) and changes
related to supporting ACPI on ARM.
Apart from that we have hibernation changes making it use radix trees
to store memory bitmaps which should speed up some operations carried
out by it quite significantly. We also have some power management
changes related to suspend-to-idle (the "freeze" sleep state) support
and more preliminary changes needed to support ACPI on ARM (outside of
ACPICA).
The rest is fixes and cleanups pretty much everywhere.
Specifics:
- ACPICA update to upstream version 20140724. That includes ACPI 5.1
material (support for the _CCA and _DSD predefined names, changes
related to the DMAR and PCCT tables and ARM support among other
things) and cleanups related to using ACPICA's header files. A
major part of it is related to acpidump and the core code used by
that utility. Changes from Bob Moore, David E Box, Lv Zheng,
Sascha Wildner, Tomasz Nowicki, Hanjun Guo.
- Radix trees for memory bitmaps used by the hibernation core from
Joerg Roedel.
- Support for waking up the system from suspend-to-idle (also known
as the "freeze" sleep state) using ACPI-based PCI wakeup signaling
(Rafael J Wysocki).
- Fixes for issues related to ACPI button events (Rafael J Wysocki).
- New device ID for an ACPI-enumerated device included into the
Wildcat Point PCH from Jie Yang.
- ACPI video updates related to backlight handling from Hans de Goede
and Linus Torvalds.
- Preliminary changes needed to support ACPI on ARM from Hanjun Guo
and Graeme Gregory.
- ACPI PNP core cleanups from Arjun Sreedharan and Zhang Rui.
- Cleanups related to ACPI_COMPANION() and ACPI_HANDLE() macros
(Rafael J Wysocki).
- ACPI-based device hotplug cleanups from Wei Yongjun and Rafael J
Wysocki.
- Cleanups and improvements related to system suspend from Lan
Tianyu, Randy Dunlap and Rafael J Wysocki.
- ACPI battery cleanup from Wei Yongjun.
- cpufreq core fixes from Viresh Kumar.
- Elimination of a deadband effect from the cpufreq ondemand governor
and intel_pstate driver cleanups from Stratos Karafotis.
- 350MHz CPU support for the powernow-k6 cpufreq driver from Mikulas
Patocka.
- Fix for the imx6 cpufreq driver from Anson Huang.
- cpuidle core and governor cleanups from Daniel Lezcano, Sandeep
Tripathy and Mohammad Merajul Islam Molla.
- Build fix for the big_little cpuidle driver from Sachin Kamat.
- Configuration fix for the Operation Performance Points (OPP)
framework from Mark Brown.
- APM cleanup from Jean Delvare.
- cpupower utility fixes and cleanups from Peter Senna Tschudin,
Andrey Utkin, Himangi Saraogi, Rickard Strandqvist, Thomas
Renninger"
* tag 'pm+acpi-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (118 commits)
ACPI / LPSS: add LPSS device for Wildcat Point PCH
ACPI / PNP: Replace faulty is_hex_digit() by isxdigit()
ACPICA: Update version to 20140724.
ACPICA: ACPI 5.1: Update for PCCT table changes.
ACPICA/ARM: ACPI 5.1: Update for GTDT table changes.
ACPICA/ARM: ACPI 5.1: Update for MADT changes.
ACPICA/ARM: ACPI 5.1: Update for FADT changes.
ACPICA: ACPI 5.1: Support for the _CCA predifined name.
ACPICA: ACPI 5.1: New notify value for System Affinity Update.
ACPICA: ACPI 5.1: Support for the _DSD predefined name.
ACPICA: Debug object: Add current value of Timer() to debug line prefix.
ACPICA: acpihelp: Add UUID support, restructure some existing files.
ACPICA: Utilities: Fix local printf issue.
ACPICA: Tables: Update for DMAR table changes.
ACPICA: Remove some extraneous printf arguments.
ACPICA: Update for comments/formatting. No functional changes.
ACPICA: Disassembler: Add support for the ToUUID opererator (macro).
ACPICA: Remove a redundant cast to acpi_size for ACPI_OFFSET() macro.
ACPICA: Work around an ancient GCC bug.
ACPI / processor: Make it possible to get local x2apic id via _MAT
...
This patch introduces zone_for_memory() to arch_add_memory() on ia64 to
ensure new, higher memory added into ZONE_MOVABLE if movable zone has
already setup.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: "Mel Gorman" <mgorman@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
See commit c6e9d6f388
random: introduce getrandom(2) system call
for all the details (and even a manual page!)
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use the more generic functions get_signal() signal_setup_done()
for signal delivery.
This inverts also the return codes of force_sigsegv_info()
and setup_frame() to follow the kernel convention.
Signed-off-by: Richard Weinberger <richard@nod.at>
Pull timer and time updates from Thomas Gleixner:
"A rather large update of timers, timekeeping & co
- Core timekeeping code is year-2038 safe now for 32bit machines.
Now we just need to fix all in kernel users and the gazillion of
user space interfaces which rely on timespec/timeval :)
- Better cache layout for the timekeeping internal data structures.
- Proper nanosecond based interfaces for in kernel users.
- Tree wide cleanup of code which wants nanoseconds but does hoops
and loops to convert back and forth from timespecs. Some of it
definitely belongs into the ugly code museum.
- Consolidation of the timekeeping interface zoo.
- A fast NMI safe accessor to clock monotonic for tracing. This is a
long standing request to support correlated user/kernel space
traces. With proper NTP frequency correction it's also suitable
for correlation of traces accross separate machines.
- Checkpoint/restart support for timerfd.
- A few NOHZ[_FULL] improvements in the [hr]timer code.
- Code move from kernel to kernel/time of all time* related code.
- New clocksource/event drivers from the ARM universe. I'm really
impressed that despite an architected timer in the newer chips SoC
manufacturers insist on inventing new and differently broken SoC
specific timers.
[ Ed. "Impressed"? I don't think that word means what you think it means ]
- Another round of code move from arch to drivers. Looks like most
of the legacy mess in ARM regarding timers is sorted out except for
a few obnoxious strongholds.
- The usual updates and fixlets all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (114 commits)
timekeeping: Fixup typo in update_vsyscall_old definition
clocksource: document some basic timekeeping concepts
timekeeping: Use cached ntp_tick_length when accumulating error
timekeeping: Rework frequency adjustments to work better w/ nohz
timekeeping: Minor fixup for timespec64->timespec assignment
ftrace: Provide trace clocks monotonic
timekeeping: Provide fast and NMI safe access to CLOCK_MONOTONIC
seqcount: Add raw_write_seqcount_latch()
seqcount: Provide raw_read_seqcount()
timekeeping: Use tk_read_base as argument for timekeeping_get_ns()
timekeeping: Create struct tk_read_base and use it in struct timekeeper
timekeeping: Restructure the timekeeper some more
clocksource: Get rid of cycle_last
clocksource: Move cycle_last validation to core code
clocksource: Make delta calculation a function
wireless: ath9k: Get rid of timespec conversions
drm: vmwgfx: Use nsec based interfaces
drm: i915: Use nsec based interfaces
timekeeping: Provide ktime_get_raw()
hangcheck-timer: Use ktime_get_ns()
...
Currently, the IRQFD code is conditional on CONFIG_HAVE_KVM_IRQ_ROUTING.
So that we can have the IRQFD code compiled in without having the
IRQ routing code, this creates a new CONFIG_HAVE_KVM_IRQFD, makes
the IRQFD code conditional on it instead of CONFIG_HAVE_KVM_IRQ_ROUTING,
and makes all the platforms that currently select HAVE_KVM_IRQ_ROUTING
also select HAVE_KVM_IRQFD.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Tested-by: Eric Auger <eric.auger@linaro.org>
Tested-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Highlights in this release include:
- BookE: Rework instruction fetch, not racy anymore now
- BookE HV: Fix ONE_REG accessors for some in-hardware registers
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S: Some misc bug fixes
- Book3S HV: Add in-guest debug support
- Book3S HV: Preload cache lines on context switch
- Remove 440 support
Alexander Graf (31):
KVM: PPC: Book3s PR: Disable AIL mode with OPAL
KVM: PPC: Book3s HV: Fix tlbie compile error
KVM: PPC: Book3S PR: Handle hyp doorbell exits
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Book3S PR: Fix sparse endian checks
PPC: Add asm helpers for BE 32bit load/store
KVM: PPC: Book3S HV: Make HTAB code LE host aware
KVM: PPC: Book3S HV: Access guest VPA in BE
KVM: PPC: Book3S HV: Access host lppaca and shadow slb in BE
KVM: PPC: Book3S HV: Access XICS in BE
KVM: PPC: Book3S HV: Fix ABIv2 on LE
KVM: PPC: Book3S HV: Enable for little endian hosts
KVM: PPC: Book3S: Move vcore definition to end of kvm_arch struct
KVM: PPC: Deflect page write faults properly in kvmppc_st
KVM: PPC: Book3S: Stop PTE lookup on write errors
KVM: PPC: Book3S: Add hack for split real mode
KVM: PPC: Book3S: Make magic page properly 4k mappable
KVM: PPC: Remove 440 support
KVM: Rename and add argument to check_extension
KVM: Allow KVM_CHECK_EXTENSION on the vm fd
KVM: PPC: Book3S: Provide different CAPs based on HV or PR mode
KVM: PPC: Implement kvmppc_xlate for all targets
KVM: PPC: Move kvmppc_ld/st to common code
KVM: PPC: Remove kvmppc_bad_hva()
KVM: PPC: Use kvm_read_guest in kvmppc_ld
KVM: PPC: Handle magic page in kvmppc_ld/st
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Remove DCR handling
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: PR: Handle FSCR feature deselects
Alexey Kardashevskiy (1):
KVM: PPC: Book3S: Fix LPCR one_reg interface
Aneesh Kumar K.V (4):
KVM: PPC: BOOK3S: PR: Fix PURR and SPURR emulation
KVM: PPC: BOOK3S: PR: Emulate virtual timebase register
KVM: PPC: BOOK3S: PR: Emulate instruction counter
KVM: PPC: BOOK3S: HV: Update compute_tlbie_rb to handle 16MB base page
Anton Blanchard (2):
KVM: PPC: Book3S HV: Fix ABIv2 indirect branch issue
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
Bharat Bhushan (10):
kvm: ppc: bookehv: Added wrapper macros for shadow registers
kvm: ppc: booke: Use the shared struct helpers of SRR0 and SRR1
kvm: ppc: booke: Use the shared struct helpers of SPRN_DEAR
kvm: ppc: booke: Add shared struct helpers of SPRN_ESR
kvm: ppc: booke: Use the shared struct helpers for SPRN_SPRG0-7
kvm: ppc: Add SPRN_EPR get helper function
kvm: ppc: bookehv: Save restore SPRN_SPRG9 on guest entry exit
KVM: PPC: Booke-hv: Add one reg interface for SPRG9
KVM: PPC: Remove comment saying SPRG1 is used for vcpu pointer
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
Michael Neuling (1):
KVM: PPC: Book3S HV: Add H_SET_MODE hcall handling
Mihai Caraman (8):
KVM: PPC: e500mc: Enhance tlb invalidation condition on vcpu schedule
KVM: PPC: e500: Fix default tlb for victim hint
KVM: PPC: e500: Emulate power management control SPR
KVM: PPC: e500mc: Revert "add load inst fixup"
KVM: PPC: Book3e: Add TLBSEL/TSIZE defines for MAS0/1
KVM: PPC: Book3s: Remove kvmppc_read_inst() function
KVM: PPC: Allow kvmppc_get_last_inst() to fail
KVM: PPC: Bookehv: Get vcpu's last instruction for emulation
Paul Mackerras (4):
KVM: PPC: Book3S: Controls for in-kernel sPAPR hypercall handling
KVM: PPC: Book3S: Allow only implemented hcalls to be enabled or disabled
KVM: PPC: Book3S PR: Take SRCU read lock around RTAS kvm_read_guest() call
KVM: PPC: Book3S: Make kvmppc_ld return a more accurate error indication
Stewart Smith (2):
Split out struct kvmppc_vcore creation to separate function
Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=JuLr
-----END PGP SIGNATURE-----
Merge tag 'signed-kvm-ppc-next' of git://github.com/agraf/linux-2.6 into kvm
Patch queue for ppc - 2014-08-01
Highlights in this release include:
- BookE: Rework instruction fetch, not racy anymore now
- BookE HV: Fix ONE_REG accessors for some in-hardware registers
- Book3S: Good number of LE host fixes, enable HV on LE
- Book3S: Some misc bug fixes
- Book3S HV: Add in-guest debug support
- Book3S HV: Preload cache lines on context switch
- Remove 440 support
Alexander Graf (31):
KVM: PPC: Book3s PR: Disable AIL mode with OPAL
KVM: PPC: Book3s HV: Fix tlbie compile error
KVM: PPC: Book3S PR: Handle hyp doorbell exits
KVM: PPC: Book3S PR: Fix ABIv2 on LE
KVM: PPC: Book3S PR: Fix sparse endian checks
PPC: Add asm helpers for BE 32bit load/store
KVM: PPC: Book3S HV: Make HTAB code LE host aware
KVM: PPC: Book3S HV: Access guest VPA in BE
KVM: PPC: Book3S HV: Access host lppaca and shadow slb in BE
KVM: PPC: Book3S HV: Access XICS in BE
KVM: PPC: Book3S HV: Fix ABIv2 on LE
KVM: PPC: Book3S HV: Enable for little endian hosts
KVM: PPC: Book3S: Move vcore definition to end of kvm_arch struct
KVM: PPC: Deflect page write faults properly in kvmppc_st
KVM: PPC: Book3S: Stop PTE lookup on write errors
KVM: PPC: Book3S: Add hack for split real mode
KVM: PPC: Book3S: Make magic page properly 4k mappable
KVM: PPC: Remove 440 support
KVM: Rename and add argument to check_extension
KVM: Allow KVM_CHECK_EXTENSION on the vm fd
KVM: PPC: Book3S: Provide different CAPs based on HV or PR mode
KVM: PPC: Implement kvmppc_xlate for all targets
KVM: PPC: Move kvmppc_ld/st to common code
KVM: PPC: Remove kvmppc_bad_hva()
KVM: PPC: Use kvm_read_guest in kvmppc_ld
KVM: PPC: Handle magic page in kvmppc_ld/st
KVM: PPC: Separate loadstore emulation from priv emulation
KVM: PPC: Expose helper functions for data/inst faults
KVM: PPC: Remove DCR handling
KVM: PPC: HV: Remove generic instruction emulation
KVM: PPC: PR: Handle FSCR feature deselects
Alexey Kardashevskiy (1):
KVM: PPC: Book3S: Fix LPCR one_reg interface
Aneesh Kumar K.V (4):
KVM: PPC: BOOK3S: PR: Fix PURR and SPURR emulation
KVM: PPC: BOOK3S: PR: Emulate virtual timebase register
KVM: PPC: BOOK3S: PR: Emulate instruction counter
KVM: PPC: BOOK3S: HV: Update compute_tlbie_rb to handle 16MB base page
Anton Blanchard (2):
KVM: PPC: Book3S HV: Fix ABIv2 indirect branch issue
KVM: PPC: Assembly functions exported to modules need _GLOBAL_TOC()
Bharat Bhushan (10):
kvm: ppc: bookehv: Added wrapper macros for shadow registers
kvm: ppc: booke: Use the shared struct helpers of SRR0 and SRR1
kvm: ppc: booke: Use the shared struct helpers of SPRN_DEAR
kvm: ppc: booke: Add shared struct helpers of SPRN_ESR
kvm: ppc: booke: Use the shared struct helpers for SPRN_SPRG0-7
kvm: ppc: Add SPRN_EPR get helper function
kvm: ppc: bookehv: Save restore SPRN_SPRG9 on guest entry exit
KVM: PPC: Booke-hv: Add one reg interface for SPRG9
KVM: PPC: Remove comment saying SPRG1 is used for vcpu pointer
KVM: PPC: BOOKEHV: rename e500hv_spr to bookehv_spr
Michael Neuling (1):
KVM: PPC: Book3S HV: Add H_SET_MODE hcall handling
Mihai Caraman (8):
KVM: PPC: e500mc: Enhance tlb invalidation condition on vcpu schedule
KVM: PPC: e500: Fix default tlb for victim hint
KVM: PPC: e500: Emulate power management control SPR
KVM: PPC: e500mc: Revert "add load inst fixup"
KVM: PPC: Book3e: Add TLBSEL/TSIZE defines for MAS0/1
KVM: PPC: Book3s: Remove kvmppc_read_inst() function
KVM: PPC: Allow kvmppc_get_last_inst() to fail
KVM: PPC: Bookehv: Get vcpu's last instruction for emulation
Paul Mackerras (4):
KVM: PPC: Book3S: Controls for in-kernel sPAPR hypercall handling
KVM: PPC: Book3S: Allow only implemented hcalls to be enabled or disabled
KVM: PPC: Book3S PR: Take SRCU read lock around RTAS kvm_read_guest() call
KVM: PPC: Book3S: Make kvmppc_ld return a more accurate error indication
Stewart Smith (2):
Split out struct kvmppc_vcore creation to separate function
Use the POWER8 Micro Partition Prefetch Engine in KVM HV on POWER8
Conflicts:
Documentation/virtual/kvm/api.txt
Pull EFI changes from Ingo Molnar:
"Main changes in this cycle are:
- arm64 efi stub fixes, preservation of FP/SIMD registers across
firmware calls, and conversion of the EFI stub code into a static
library - Ard Biesheuvel
- Xen EFI support - Daniel Kiper
- Support for autoloading the efivars driver - Lee, Chun-Yi
- Use the PE/COFF headers in the x86 EFI boot stub to request that
the stub be loaded with CONFIG_PHYSICAL_ALIGN alignment - Michael
Brown
- Consolidate all the x86 EFI quirks into one file - Saurabh Tangri
- Additional error logging in x86 EFI boot stub - Ulf Winkelvos
- Support loading initrd above 4G in EFI boot stub - Yinghai Lu
- EFI reboot patches for ACPI hardware reduced platforms"
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (31 commits)
efi/arm64: Handle missing virtual mapping for UEFI System Table
arch/x86/xen: Silence compiler warnings
xen: Silence compiler warnings
x86/efi: Request desired alignment via the PE/COFF headers
x86/efi: Add better error logging to EFI boot stub
efi: Autoload efivars
efi: Update stale locking comment for struct efivars
arch/x86: Remove efi_set_rtc_mmss()
arch/x86: Replace plain strings with constants
xen: Put EFI machinery in place
xen: Define EFI related stuff
arch/x86: Remove redundant set_bit(EFI_MEMMAP) call
arch/x86: Remove redundant set_bit(EFI_SYSTEM_TABLES) call
efi: Introduce EFI_PARAVIRT flag
arch/x86: Do not access EFI memory map if it is not available
efi: Use early_mem*() instead of early_io*()
arch/ia64: Define early_memunmap()
x86/reboot: Add EFI reboot quirk for ACPI Hardware Reduced flag
efi/reboot: Allow powering off machines using EFI
efi/reboot: Add generic wrapper around EfiResetSystem()
...
Pull locking updates from Ingo Molnar:
"The main changes in this cycle are:
- big rtmutex and futex cleanup and robustification from Thomas
Gleixner
- mutex optimizations and refinements from Jason Low
- arch_mutex_cpu_relax() removal and related cleanups
- smaller lockdep tweaks"
* 'locking-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
arch, locking: Ciao arch_mutex_cpu_relax()
locking/lockdep: Only ask for /proc/lock_stat output when available
locking/mutexes: Optimize mutex trylock slowpath
locking/mutexes: Try to acquire mutex only if it is unlocked
locking/mutexes: Delete the MUTEX_SHOW_NO_WAITER macro
locking/mutexes: Correct documentation on mutex optimistic spinning
rtmutex: Make the rtmutex tester depend on BROKEN
futex: Simplify futex_lock_pi_atomic() and make it more robust
futex: Split out the first waiter attachment from lookup_pi_state()
futex: Split out the waiter check from lookup_pi_state()
futex: Use futex_top_waiter() in lookup_pi_state()
futex: Make unlock_pi more robust
rtmutex: Avoid pointless requeueing in the deadlock detection chain walk
rtmutex: Cleanup deadlock detector debug logic
rtmutex: Confine deadlock logic to futex
rtmutex: Simplify remove_waiter()
rtmutex: Document pi chain walk
rtmutex: Clarify the boost/deboost part
rtmutex: No need to keep task ref for lock owner check
rtmutex: Simplify and document try_to_take_rtmutex()
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=hP9S
-----END PGP SIGNATURE-----
Merge tag 'please-pull-misc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull ia64 cleanups from Tony Luck:
"Miscellaneous ia64 specific cleanup"
* tag 'please-pull-misc-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
[IA64] sn: Do not needlessly convert between pointers and integers
[IA64] sn: Fix zeroing of PDAs
In commit 4a0e637738 ("clocksource: Get rid of cycle_last"),
currently in the -tip tree, there was a small typo where cycles_t
was used intstead of cycle_t. This broke ppc64 builds.
Fix this by using the proper cycle_t type for this usage, in
both the definition and the ia64 implementation.
Now, having both cycle_t and cycles_t types seems like a very
bad idea just asking for these sorts of issues. But that
will be a cleanup for another day.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1406349439-11785-1-git-send-email-john.stultz@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nasid_to_try variable is an array of integers, so plain integers can
be used when assigning values to the elements rather than casting a NULL
pointer to an integer, which results in the following warning from GCC:
arch/ia64/sn/kernel/bte.c:117:22: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
nasid_to_try[1] = (int)NULL;
^
arch/ia64/sn/kernel/bte.c:125:22: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
nasid_to_try[1] = (int)NULL;
^
Replace (int)NULL with a simple 0 to silence these warnings.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The code uses a the following to zero out a PDA:
memset(pda, 0, sizeof(pda));
But sizeof(pda) will return the size of a pointer rather than the size
of the structure pointed to. This triggers the following warning from
GCC:
arch/ia64/sn/kernel/setup.c:582:23: warning: argument to 'sizeof' in 'memset' call is the same pointer type 'struct pda_s *' as the destination; expected 'struct pda_s' or an explicit length [-Wsizeof-pointer-memaccess]
memset(pda, 0, sizeof(pda));
^
Fix this by passing in the size of the structure using sizeof(*pda)
instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In preparation to make the check_extension function available to VM scope
we add a struct kvm * argument to the function header and rename the function
accordingly. It will still be called from the /dev/kvm fd, but with a NULL
argument for struct kvm *.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
cycle_last was added to the clocksource to support the TSC
validation. We moved that to the core code, so we can get rid of the
extra copy.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Stultz <john.stultz@linaro.org>
The forthcoming patch will make <acpi/acpi.h> to be visible to all kernel
source code. Thus for the architectures that do not support ACPI and
haven't implemented <asm/acenv.h>, we need to make it excluded.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The use of _PDC is deprecated in ACPI 3.0 in favor of _OSC,
as ARM platform is supported only in ACPI 5.0 or higher version,
_PDC will not be used in ARM platform, so make Make _PDC only for
platforms with Intel CPUs.
Introduce ARCH_MIGHT_HAVE_ACPI_PDC and move _PDC related code in
ACPI processor driver into a single file processor_pdc.c, make x86
and ia64 select it when ACPI is enabled.
This patch also use pr_* to replace printk to fix the checkpatch
warning and factor acpi_processor_alloc_pdc() a little bit to
avoid duplicate pr_err() code.
Suggested-by: Robert Richter <rric@kernel.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now ARM64 support is being added to ACPI so architecture specific
values can not be used in core ACPI code.
Following on the patch "ACPI / processor: Check if LAPIC is present
during initialization" which uses acpi_lapic in acpi_processor.c,
on ARM64 platform, GIC is used instead of local APIC, so acpi_lapic
is not a suitable value for ARM64.
What is actually important at this point is if there is/are CPU
entry/entries (Local APIC/SAPIC, GICC) in MADT, so introduce
acpi_has_cpu_in_madt() to be arch specific and generic.
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is odd to use early_iounmap() function do tear down mapping
created by early_memremap() function, even if it works right now,
because they belong to different set of functions. The former is
I/O related function and the later is memory related. So, create
early_memunmap() macro which in real is early_iounmap(). This
thing will help to not confuse code readers longer by mixing
functions from different classes.
EFI patches following this patch uses that functionality.
Signed-off-by: Daniel Kiper <daniel.kiper@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Implement efi_reboot(), which is really just a wrapper around the
EfiResetSystem() EFI runtime service, but it does at least allow us to
funnel all callers through a single location.
It also simplifies the callsites since users no longer need to check to
see whether EFI_RUNTIME_SERVICES are enabled.
Cc: Tony Luck <tony.luck@intel.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The specification of Python 3 is largely different from that of
Python 2.
For example, arch/ia64/scripts/unwcheck.py seems to be written
in Python 2, not compatible with Python 3.
It is not a good idea to invoke python scripts with the hard-coded
command name 'python'. The command 'python' could possibly be
Python 3 on some systems.
For that case, it is reasonable to allow to override the command name
by giving 'PYTHON=python2' from the command line.
The 'python' in arch/ia64/Makefile should be replaced with '$(PYTHON)'.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: linux-ia64@vger.kernel.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
The arch_mutex_cpu_relax() function, introduced by 34b133f, is
hacky and ugly. It was added a few years ago to address the fact
that common cpu_relax() calls include yielding on s390, and thus
impact the optimistic spinning functionality of mutexes. Nowadays
we use this function well beyond mutexes: rwsem, qrwlock, mcs and
lockref. Since the macro that defines the call is in the mutex header,
any users must include mutex.h and the naming is misleading as well.
This patch (i) renames the call to cpu_relax_lowlatency ("relax, but
only if you can do it with very low latency") and (ii) defines it in
each arch's asm/processor.h local header, just like for regular cpu_relax
functions. On all archs, except s390, cpu_relax_lowlatency is simply cpu_relax,
and thus we can take it out of mutex.h. While this can seem redundant,
I believe it is a good choice as it allows us to move out arch specific
logic from generic locking primitives and enables future(?) archs to
transparently define it, similarly to System Z.
Signed-off-by: Davidlohr Bueso <davidlohr@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Blanchard <anton@samba.org>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Bharat Bhushan <r65777@freescale.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chen Liqin <liqin.linux@gmail.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: David Howells <dhowells@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Cc: Dominik Dingel <dingel@linux.vnet.ibm.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Joe Perches <joe@perches.com>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: Joseph Myers <joseph@codesourcery.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Neuling <mikey@neuling.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Nicolas Pitre <nico@linaro.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: Qiaowei Ren <qiaowei.ren@intel.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Steven Miao <realmz6@gmail.com>
Cc: Steven Rostedt <srostedt@redhat.com>
Cc: Stratos Karafotis <stratosk@semaphore.gr>
Cc: Tim Chen <tim.c.chen@linux.intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vasily Kulikov <segoon@openwall.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Vineet Gupta <Vineet.Gupta1@synopsys.com>
Cc: Waiman Long <Waiman.Long@hp.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: adi-buildroot-devel@lists.sourceforge.net
Cc: linux390@de.ibm.com
Cc: linux-alpha@vger.kernel.org
Cc: linux-am33-list@redhat.com
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-c6x-dev@linux-c6x.org
Cc: linux-cris-kernel@axis.com
Cc: linux-hexagon@vger.kernel.org
Cc: linux-ia64@vger.kernel.org
Cc: linux@lists.openrisc.net
Cc: linux-m32r-ja@ml.linux-m32r.org
Cc: linux-m32r@ml.linux-m32r.org
Cc: linux-m68k@lists.linux-m68k.org
Cc: linux-metag@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: linux-parisc@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-s390@vger.kernel.org
Cc: linux-sh@vger.kernel.org
Cc: linux-xtensa@linux-xtensa.org
Cc: sparclinux@vger.kernel.org
Link: http://lkml.kernel.org/r/1404079773.2619.4.camel@buesod1.americas.hpqcorp.net
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Commit b4aa016305 ("efifb: Implement vga_default_device() (v2)") added
efifb vga_default_device() so EFI systems that do not load shadow VBIOS or
setup VGA get proper value for boot_vga PCI sysfs attribute on the
corresponding PCI device.
Xorg doesn't detect devices when boot_vga=0, e.g., on some EFI systems such
as MacBookAir2,1. Xorg detects the GPU and finds the DRI device but then
bails out with "no devices detected".
Note: When vga_default_device() is set boot_vga PCI sysfs attribute
reflects its state. When unset this attribute is 1 whenever
IORESOURCE_ROM_SHADOW flag is set.
With introduction of sysfb/simplefb/simpledrm efifb is getting obsolete
while having native drivers for the GPU also makes selecting sysfb/efifb
optional.
Remove the efifb implementation of vga_default_device() and initialize
vgaarb's vga_default_device() with the PCI GPU that matches boot
screen_info in pci_fixup_video().
[bhelgaas: remove unused "dev" in efifb_setup()]
Fixes: b4aa016305 ("efifb: Implement vga_default_device() (v2)")
Tested-by: Anibal Francisco Martinez Cortina <linuxkid.zeuz@gmail.com>
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Matthew Garrett <matthew.garrett@nebula.com>
CC: stable@vger.kernel.org # v3.5+
fs/notify/fanotify/fanotify_user.c: In function 'SYSC_fanotify_init':
fs/notify/fanotify/fanotify_user.c:726: error: implicit declaration of function 'personality'
fs/notify/fanotify/fanotify_user.c:726: error: 'PER_LINUX32' undeclared (first use in this function)
fs/notify/fanotify/fanotify_user.c:726: error: (Each undeclared identifier is reported only once
fs/notify/fanotify/fanotify_user.c:726: error: for each function it appears in.)
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Cc: Will Woods <wwoods@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: <stable@vger.kernel.org> [3.15.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 66345d5f79 (ACPI / ia64 / sba_iommu: Use ACPI scan handler
for device discovery) changed the ordering of SBA (System Bus Adapter)
IOMMU initialization with respect to the PCI host bridge initialization
which broke things inadvertently, because the SBA IOMMU initialization
code has to run after the PCI host bridge has been initialized.
Fix that by reworking the SBA IOMMU ACPI scan handler so that it
claims the discovered matching ACPI device objects without attempting
to initialize anything and move the entire SBA IOMMU initialization
to sba_init() that runs after the PCI bus has been enumerated.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=76691
Fixes: 66345d5f79 (ACPI / ia64 / sba_iommu: Use ACPI scan handler for device discovery)
Reported-and-tested-by: Émeric Maschino <emeric.maschino@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This typedef is unnecessary and should just be removed.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc updates from Andrew Morton:
- a few fixes for 3.16. Cc'ed to stable so they'll get there somehow.
- various misc fixes and cleanups
- most of the ocfs2 queue. Review is slow...
- most of MM. The MM queue is pretty huge this time, but not much in
the way of feature work.
- some tweaks under kernel/
- printk maintenance work
- updates to lib/
- checkpatch updates
- tweaks to init/
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (276 commits)
fs/autofs4/dev-ioctl.c: add __init to autofs_dev_ioctl_init
fs/ncpfs/getopt.c: replace simple_strtoul by kstrtoul
init/main.c: remove an ifdef
kthreads: kill CLONE_KERNEL, change kernel_thread(kernel_init) to avoid CLONE_SIGHAND
init/main.c: add initcall_blacklist kernel parameter
init/main.c: don't use pr_debug()
fs/binfmt_flat.c: make old_reloc() static
fs/binfmt_elf.c: fix bool assignements
fs/efs: convert printk(KERN_DEBUG to pr_debug
fs/efs: add pr_fmt / use __func__
fs/efs: convert printk to pr_foo()
scripts/checkpatch.pl: device_initcall is not the only __initcall substitute
checkpatch: check stable email address
checkpatch: warn on unnecessary void function return statements
checkpatch: prefer kstrto<foo> to sscanf(buf, "%<lhuidx>", &bar);
checkpatch: add warning for kmalloc/kzalloc with multiply
checkpatch: warn on #defines ending in semicolon
checkpatch: make --strict a default for files in drivers/net and net/
checkpatch: always warn on missing blank line after variable declaration block
checkpatch: fix wildcard DT compatible string checking
...
Linus Torvalds