As tests are added to kunit, it will become less feasible to execute
all built tests together. By supporting modular tests we provide
a simple way to do selective execution on a running system; specifying
CONFIG_KUNIT=y
CONFIG_KUNIT_EXAMPLE_TEST=m
...means we can simply "insmod example-test.ko" to run the tests.
To achieve this we need to do the following:
o export the required symbols in kunit
o string-stream tests utilize non-exported symbols so for now we skip
building them when CONFIG_KUNIT_TEST=m.
o drivers/base/power/qos-test.c contains a few unexported interface
references, namely freq_qos_read_value() and freq_constraints_init().
Both of these could be potentially defined as static inline functions
in include/linux/pm_qos.h, but for now we simply avoid supporting
module build for that test suite.
o support a new way of declaring test suites. Because a module cannot
do multiple late_initcall()s, we provide a kunit_test_suites() macro
to declare multiple suites within the same module at once.
o some test module names would have been too general ("test-test"
and "example-test" for kunit tests, "inode-test" for ext4 tests);
rename these as appropriate ("kunit-test", "kunit-example-test"
and "ext4-inode-test" respectively).
Also define kunit_test_suite() via kunit_test_suites()
as callers in other trees may need the old definition.
Co-developed-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Knut Omang <knut.omang@oracle.com>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Acked-by: Theodore Ts'o <tytso@mit.edu> # for ext4 bits
Acked-by: David Gow <davidgow@google.com> # For list-test
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
KUnit tests for decoding extended 64 bit timestamps that verify the
seconds part of [a/c/m] timestamps in ext4 inode structs are decoded
correctly.
Test data is derived from the table in the Inode Timestamps section of
Documentation/filesystems/ext4/inodes.rst.
KUnit tests run during boot and output the results to the debug log
in TAP format (http://testanything.org/). Only useful for kernel devs
running KUnit test harness and are not for inclusion into a production
build.
Signed-off-by: Iurii Zaikin <yzaikin@google.com>
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Reviewed-by: Brendan Higgins <brendanhiggins@google.com>
Tested-by: Brendan Higgins <brendanhiggins@google.com>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
Add most of fs-verity support to ext4. fs-verity is a filesystem
feature that enables transparent integrity protection and authentication
of read-only files. It uses a dm-verity like mechanism at the file
level: a Merkle tree is used to verify any block in the file in
log(filesize) time. It is implemented mainly by helper functions in
fs/verity/. See Documentation/filesystems/fsverity.rst for the full
documentation.
This commit adds all of ext4 fs-verity support except for the actual
data verification, including:
- Adding a filesystem feature flag and an inode flag for fs-verity.
- Implementing the fsverity_operations to support enabling verity on an
inode and reading/writing the verity metadata.
- Updating ->write_begin(), ->write_end(), and ->writepages() to support
writing verity metadata pages.
- Calling the fs-verity hooks for ->open(), ->setattr(), and ->ioctl().
ext4 stores the verity metadata (Merkle tree and fsverity_descriptor)
past the end of the file, starting at the first 64K boundary beyond
i_size. This approach works because (a) verity files are readonly, and
(b) pages fully beyond i_size aren't visible to userspace but can be
read/written internally by ext4 with only some relatively small changes
to ext4. This approach avoids having to depend on the EA_INODE feature
and on rearchitecturing ext4's xattr support to support paging
multi-gigabyte xattrs into memory, and to support encrypting xattrs.
Note that the verity metadata *must* be encrypted when the file is,
since it contains hashes of the plaintext data.
This patch incorporates work by Theodore Ts'o and Chandan Rajendra.
Reviewed-by: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support the GETFSMAP ioctls so that we can use the xfs free space
management tools to probe ext4 as well. Note that this is a partial
implementation -- we only report fixed-location metadata and free space;
everything else is reported as "unknown".
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This patch removes the most parts of internal crypto codes.
And then, it modifies and adds some ext4-specific crypt codes to use the generic
facility.
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Also statically allocate the ext4_kset and ext4_feat objects, since we
only need exactly one of each, and it's simpler and less code if we
drop the dynamic allocation and deallocation when it's not needed.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
On encrypt, we will re-assign the buffer_heads to point to a bounce
page rather than the control_page (which is the original page to write
that contains the plaintext). The block I/O occurs against the bounce
page. On write completion, we re-assign the buffer_heads to the
original plaintext page.
On decrypt, we will attach a read completion callback to the bio
struct. This read completion will decrypt the read contents in-place
prior to setting the page up-to-date.
The current encryption mode, AES-256-XTS, lacks cryptographic
integrity. AES-256-GCM is in-plan, but we will need to devise a
mechanism for handling the integrity data.
Signed-off-by: Michael Halcrow <mhalcrow@google.com>
Signed-off-by: Ildar Muslukhov <ildarm@google.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This takes code from fs/mpage.c and optimizes it for ext4. Its
primary reason is to allow us to more easily add encryption to ext4's
read path in an efficient manner.
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Ted has sent out a RFC about removing this feature. Eric and Jan
confirmed that both RedHat and SUSE enable this feature in all their
product. David also said that "As far as I know, it's enabled in all
Android kernels that use ext4." So it seems OK for us.
And what's more, as inline data depends its implementation on xattr,
and to be frank, I don't run any test again inline data enabled while
xattr disabled. So I think we should add inline data and remove this
config option in the same release.
[ The savings if you disable CONFIG_EXT4_FS_XATTR is only 27k, which
isn't much in the grand scheme of things. Since no one seems to be
testing this configuration except for some automated compile farms, on
balance we are better removing this config option, and so that it is
effectively always enabled. -- tytso ]
Cc: David Brown <davidb@codeaurora.org>
Cc: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Implement inline data with xattr.
Now we use "system.data" to store xattr, and the xattr will
be extended if the i_size is increased while we don't release
the space during truncate.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch moves functions from inode.c to indirect.c.
The moved functions are ext4_ind_* functions and their helpers.
Functions called from inode.c are declared extern.
Signed-off-by: Amir Goldstein <amir73il@users.sf.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Prevent an ext4 filesystem from being mounted multiple times.
A sequence number is stored on disk and is periodically updated (every 5
seconds by default) by a mounted filesystem.
At mount time, we now wait for s_mmp_update_interval seconds to make sure
that the MMP sequence does not change.
In case of failure, the nodename, bdevname and the time at which the MMP
block was last updated is displayed.
Signed-off-by: Andreas Dilger <adilger@whamcloud.com>
Signed-off-by: Johann Lombardi <johann@whamcloud.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Call the block I/O layer directly instad of going through the buffer
layer. This should give us much better performance and scalability,
as well as lowering our CPU utilization when doing buffered writeback.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The EXT4_IOC_MOVE_EXT exchanges the blocks between orig_fd and donor_fd,
and then write the file data of orig_fd to donor_fd.
ext4_mext_move_extent() is the main fucntion of ext4 online defrag,
and this patch includes all functions related to ext4 online defrag.
Signed-off-by: Akira Fujita <a-fujita@rs.jp.nec.com>
Signed-off-by: Takashi Sato <t-sato@yk.jp.nec.com>
Signed-off-by: Kazuya Mio <k-mio@sx.jp.nec.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
To catch filesystem bugs or corruption which could lead to the
filesystem getting severly damaged, this patch adds a facility for
tracking all of the filesystem metadata blocks by contiguous regions
in a red-black tree. This allows quick searching of the tree to
locate extents which might overlap with filesystem metadata blocks.
This facility is also used by the multi-block allocator to assure that
it is not allocating blocks out of the system zone, as well as by the
routines used when reading indirect blocks and extents information
from disk to make sure their contents are valid.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The ext4 filesystem is getting stable enough that it's time to drop
the "dev" prefix. Also remove the requirement for the TEST_FILESYS
flag.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
On disk extents format:
/*
* this is extent on-disk structure
* it's used at the bottom of the tree
*/
struct ext3_extent {
__le32 ee_block; /* first logical block extent covers */
__le16 ee_len; /* number of blocks covered by extent */
__le16 ee_start_hi; /* high 16 bits of physical block */
__le32 ee_start; /* low 32 bigs of physical block */
};
Signed-off-by: Alex Tomas <alex@clusterfs.com>
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mingming Cao originally did this work, and Shaggy reproduced it using some
scripts from her.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Start of the ext4 patch series. See Documentation/filesystems/ext4.txt for
details.
This is a simple copy of the files in fs/ext3 to fs/ext4 and
/usr/incude/linux/ext3* to /usr/include/ex4*
Signed-off-by: Dave Kleikamp <shaggy@austin.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Jan (janneke) Nieuwenhuizen