Until now the code assumes a fixed structure which makes it difficult to
support EMADs with and without new TLVs.
Make it more generic by parsing the TLVs when the EMADs are received and
store the offset to the different TLVs in the control block. Using these
offsets to extract information from the EMADs without relying on a specific
structure.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: a0c76345e3 ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a254b ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo 10 > /sys/bus/netdevsim/new_device
devlink dev reload netdevsim/netdevsim10 &
echo 10 > /sys/bus/netdevsim/del_device
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs used to report layer 3 exceptions.
Trapped packets are first reported to devlink and then injected to the
kernel's receive path. All the packets have 'offload_fwd_mark' set in
order to prevent them from potentially being forwarded by the bridge
again.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw does not differentiate between these two cases of
routes with invalid nexthops:
1. Nexthops whose nexthop device is a mlxsw upper (has a RIF), but whose
neighbour could not be resolved
2. Nexthops whose nexthop device is not a mlxsw upper (e.g., management
interface)
Up until now this did not matter and mlxsw trapped packets for both
cases using the same trap ID. However, packets that should have been
routed in hardware (case 1), but incurred a problem are considered
exceptions and should be reported to the user. The two cases should
therefore be split between two different trap IDs.
Allocate a new adjacency entry during initialization and upon the
insertion of the first route with an invalid mlxsw nexthop, program this
entry to discard packets. Packets hitting this entry will be reported
using new trap ID - "DISCARD_ROUTER3".
In the future, the entry could be written during initialization, but
currently firmware requires a valid RIF, which is not available at this
stage.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, packets that cannot be routed in hardware (e.g., nexthop
device is not upper of mlxsw), are trapped to the kernel for forwarding.
Such packets are trapped using "RTR_INGRESS0" trap. This trap also traps
packets that hit reject routes (e.g., "unreachable") so that the kernel
will generate the appropriate ICMP error message for them.
Subsequent patch will need to only report to devlink packets that hit a
reject route, which is impossible as long as "RTR_INGRESS0" is
overloaded like that.
Solve this by using "RTR_INGRESS1" trap for packets that hit reject
routes.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs and trap group used to report layer 3 drops. Register
layer 3 packet traps and associated layer 3 trap group with devlink
during driver initialization.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return negative error code -ENOMEM from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: 4a7f970f12 ("mlxsw: spectrum: Replace port_to_module array with array of structs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
When building for 32-bit ARM, there is a link time error because of a
64-bit division:
ld.lld: error: undefined symbol: __aeabi_uldivmod
>>> referenced by spectrum_buffers.c
>>> net/ethernet/mellanox/mlxsw/spectrum_buffers.o:(mlxsw_sp_buffers_init) in archive drivers/built-in.a
>>> did you mean: __aeabi_uidivmod
>>> defined in: arch/arm/lib/lib.a(lib1funcs.o
Avoid this by using div_u64, which is designed to avoid this problem.
Fixes: bc9f6e94bc ("mlxsw: spectrum_buffers: Calculate the size of the main pool")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the check generic for any possible value, not only 2 and 4.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During recreation of original unsplit ports, just simply iterate over
the whole gap and recreate whatever originally existed.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code considers only split by 2 or 4. Make the base port
getting generic and allow split by 8 to be handled correctly. Generalize
the used port checks as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using constant value, use port_module_max_width which is
aligned with the cluster size.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't compute the original base local port during unsplit, rather
remember it in mlxsw_sp_port structure during split port creation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-3 the modules have 8 lanes, so split by count 2 results in
two split ports each of 4 lanes. Add a resource that can be used to
obtain local port offset in that case.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get local port offsets of split port in a separate helper function and
use it in both split and unsplit function.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver assumes certain values in the PMLP register. Add checks that
verify that PMLP register provides fitting values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the port mapping structure down to create, module_map and other
function instead of individual values.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't use constant max width value and instead of that, use the actual
width of the port. Also don't pass module value and use the value
stored in the same structure.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Store the initial PMLP register configuration into array of structures
instead of just simple array of module numbers.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when user does split, he is not able to distinguish if the
port cannot be split because it is already split, or because it cannot
be split at all. Add another check for split flag to distinguish this.
Also add check forbidding split when maximal width is 1.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fact that the port cannot be split further should be checked before
checking the count, so move it.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the max module width is hard-coded according to ASIC type.
That is not entirely correct, as the max module width might differ
per-board. Use PMTM register to query FW for maximal width of a module.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PMTM allows query or configuration of module types.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx/rx lane fields got extended to 4 bits, update the reg field
description accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to Spectrum-1, enforce a specific firmware version
for Spectrum-2 so that the driver and firmware are always in sync with
regards to new features.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version adds support for querying port module type. It will be used
by a followup patch set from Jiri to make port split code more generic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SN3800 Spectrum-2 based systems have gearboxes that need to be
initialized by the firmware during its initialization flow. In certain
cases, the firmware might need to flash these gearboxes, which is
currently a time-consuming process.
In newer firmware versions, the firmware will not signal to the driver
that it is ready until the gearboxes are flashed. Increase the PCI reset
timeout for these situations. In normal cases, the driver will need to
wait no longer than 5 seconds.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In new firmware versions this register is extended with a sampling rate
for Spectrum-2 and future ASICs.
Increase the size of the register to ensure the field is initialized to
0 which means every packet is mirrored.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink parameter "acl_region_rehash_interval" is a runtime
parameter whose value is stored in a dynamically allocated memory. While
reloading the driver, this memory is freed and then allocated again. A
use-after-free might happen if during this time frame someone tries to
retrieve its value.
Since commit 070c63f20f ("net: devlink: allow to change namespaces
during reload") the use-after-free can be reliably triggered when
reloading the driver into a namespace, as after freeing the memory (via
reload_down() callback) all the parameters are notified.
Fix this by unpublishing and then re-publishing the parameters during
reload.
Fixes: 98bbf70c1c ("mlxsw: spectrum: add "acl_region_rehash_interval" devlink param")
Fixes: 7c62cfb8c5 ("devlink: publish params only after driver init is done")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess semicolon after closing parenthesis.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hard-coding the size of the largest pool, calculate it from the
reported guaranteed shared buffer size and sizes of other pools (currently
only the CPU port pool).
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two resources associated with shared buffer size:
cap_total_buffer_size, and cap_guaranteed_shared_buffer. So far, mlxsw has
been using the former as a limit to determine how large a pool size is
allowed to be. However, the total size also includes headrooms and reserved
space, which really cannot be used for shared buffer pools.
Therefore convert mlxsw to use the latter resource as a limit. Adjust
hard-coded pool sizes to be the guaranteed size minus 256000 bytes for CPU
port pool. On Spectrum-1 that actually leads to an increase. A follow-up
patch will have this size calculated automatically.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the size of QSFP EEPROM for the cable types SSF8436 and SFF8636
from 256 to 640 bytes in order to expose all the EEPROM pages by
ethtool.
For SFF-8636 and SFF-8436 specifications, the driver exposes 256 bytes
of data for ethtool's get_module_eeprom() callback. This is because the
driver uses the below defines to specify SFF module length in ethtool's
get_module_info() callback:
'ETH_MODULE_SFF_8636_LEN' and 'ETH_MODULE_SFF_8436_LEN' (both are 256).
As a result of exposing 256 bytes only, ethtool shows wrong "zero" info
for pages 1, 2, 3.
The patch changes the length returned by callback for get_module_info()
to the values from the next defines: 'ETH_MODULE_SFF_8636_MAX_LEN' and
'ETH_MODULE_SFF_8436_MAX_LEN' (both are 640) to allow exposing of upper
page 1, 2 and 3.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Provide a macro for getting QSFP module EEPROM page number from the
optional upper page number row offset, specified in request.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
devlink maintains packets and bytes statistics for each trap. Since
eth_type_trans() was called to set the skb's protocol, the data pointer
no longer points to the start of the packet and the bytes accounting is
off by 14 bytes.
Fix this by pushing the skb's data pointer to the start of the packet.
Fixes: b5ce611fd9 ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports an enhanced switched port analyzer that enables
selecting network traffic for analysis by a network analyzer.
SPAN agents are configured and consumed whenever a tc filter is added
with a mirror action to a new destination. The destination can either be
a physical port (e.g., swp1), a VLAN device or a gretap.
Expose the maximum number of SPAN agents and their current usage to the
user.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend speed support with 400Gbps
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add validation for FW version in order to prevent driver initialization
in case FW version is older than expected. FW version validation is
necessary, because use of a new field 'num_of_modules' in MGPIR register
is not backward compatible. FW 'minor' and 'subminor' versions are
expected to be greater than or equal to 2000 and 1886, respectively.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new API for FW "minor" and "subminor" version validation for
sharing it between "spectrum" and "minimal" drivers.
Use it in "spectrum" driver.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field "num_of_modules" of MGPIR register for "thermal" interface
in order to get the number of modules supported by system directly from
the system configuration, instead of getting it from port to module
mapping info.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field "num_of_modules" of MGPIR register for "hwmon" interface
in order to get the number of modules supported by system directly from
the system configuration, instead of getting it from port to module
mapping info.
Reading this info through MGPIR register is faster and does not depend
on possible dynamic re-configuration of ports.
In case of port dynamic re-configuration some modules can logically
"disappear" as a result of port split and un-spilt operations, which
can cause missing of some modules, in case this info is taken from port
to module mapping info.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend MGPIR - Management General Peripheral Information Register
with new field "num_of_modules" exposing the number of modules
supported by specific system.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All devlink instances are created in init_net and stay there for a
lifetime. Allow user to be able to move devlink instances into
namespaces during devlink reload operation. That ensures proper
re-instantiation of driver objects, including netdevices.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the devlink reaload the extack is present, so propagate it all
the way down to register_fib_notifier() call in spectrum_router.c.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creating netdevices for ports, put them under network namespace
that the core/parent devlink belongs to.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Follow-up patch is going to allow to reload devlink instance into
different network namespace, so use devlink_net() helper instead
of init_net.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since errors are propagated all the way up to the caller, propagate
possible extack of the caller all the way down to the notifier block
callback.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if info->extack is NULL, mlxsw assumes that the event came
down from dump. Originally, the dump did not propagate the return value
back to the original caller (fib_notifier_register()). However, that is
now happening. So benefit from this and push the error up if it happened.
Remove rule cases in work handlers that are now dead code.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently all users of FIB notifier only cares about events in init_net.
Later in this patchset, users get interested in other namespaces too.
However, for every registered block user is interested only about one
namespace. Make the FIB notifier registration per-netns and avoid
unnecessary calls of notifier block for other namespaces.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently mlxsw distributes sent traffic among all the available send
queues. That includes control traffic as well as EMADs, which are used for
configuration of the device.
However because all the queues have the same traffic class of 3, they all
end up being directed to the same traffic class buffer. If the control
traffic in the buffer cannot be serviced quickly enough, the EMAD traffic
might be shut out, which causes transient failures, typically in FDB
maintenance, counter upkeep and other periodic work.
To address this issue, dedicate SDQ 0 to EMAD traffic, with TC 0.
Distribute the control traffic among the remaining queues, which are left
with their current TC 3.
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlxsw_sp instance is not interested in events happening in other
network namespaces. So use "_net" variants for netdevice notifier
registration/unregistration and get only events which are happening in
the net the instance is in.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ASIC can only mirror a packet to one port, but when user is trying
to set more than one mirror action, it doesn't fail.
Add a check if more than one mirror action was specified per rule and if so,
fail for not being supported.
Fixes: d0d13c1858 ("mlxsw: spectrum_acl: Add support for mirror action")
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a port is created, its VLAN filters are not cleared by the
firmware. This causes tagged packets to be later dropped by the ingress
STP filters, which default to DISCARD state.
The above did not matter much until commit b5ce611fd9 ("mlxsw:
spectrum: Add devlink-trap support") where we exposed the drop reason to
users.
Without this patch, the drop reason users will see is not consistent. If
a port is enslaved to a VLAN-aware bridge and a packet with an invalid
VLAN tries to ingress the bridge, it will be dropped due to ingress STP
filter. If the VLAN is later enabled and then disabled, the packet will
be dropped by the ingress VLAN filter despite the above being a
seemingly NOP operation.
Fix this by clearing all the VLAN filters during port initialization.
Adjust the test accordingly.
Fixes: b5ce611fd9 ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While debugging packet loss towards the CPU, it is useful to be able to
query the CPU port's shared buffer quotas and occupancy.
Since the CPU port has no ingress buffers, all the shared buffers ingress
information will be cleared.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register CPU port with devlink.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch is going to register the CPU port with devlink, but only so
that the CPU port's shared buffer configuration and occupancy could be
queried.
Prevent changing CPU port's shared buffer threshold and binding
configuration.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the fact that devlink reload failed is stored in drivers.
Move this flag into devlink core. Also, expose it to the user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly implement failure indication during reload,
split the reload op into two ops, one for down phase and one for
up phase.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamped PTP packets and the corresponding timestamps need to
be kept in caches until both are available, at which point they are matched up
and packets forwarded as appropriate. However, not all packets will ever see
their timestamp, and not all timestamps will ever see their packet. It is
necessary to dispose of such abandoned entries, so a garbage collector was
introduced in commit 5d23e41597 ("mlxsw: spectrum: PTP: Garbage-collect
unmatched entries").
If these GC events happen often, it is a sign of a problem. However because this
whole mechanism is taking place behind the scenes, there is no direct way to
determine whether garbage collection took place.
Therefore to fix this, on Spectrum-1 only, expose four artificial ethtool
counters for the GC events: GCd timestamps and packets, in TX and RX directions.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new version supports extended error reporting from firmware via a
new TLV in the EMAD packet. Similar to netlink extended ack.
It also fixes an issue in the PCI code that can result in false AER
errors under high Tx rate.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 50G-1-lane and 100G-2-lanes link modes were introduced, the driver
is facing situations in which the hardware auto negotiates not only on
speed and type, but also on number of lanes.
Prevent auto negotiation on number of lanes by allowing only port speeds
that can be supported on a given port according to its width.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 275e928f19 ("mlxsw: spectrum: Prevent force of 56G") prevented
the driver from setting a speed of 56G when auto-negotiation is off.
This is the only speed supported by mlxsw that cannot be set when
auto-negotiation is off, which makes it difficult to write generic
tests.
Further, the speed is not supported by newer ASICs such as Spectrum-2
and to the best of our knowledge it is not used by current users.
Therefore, remove 56G support from mlxsw.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register supported packet traps (layer 2 drops only, currently) and
associated trap group with devlink during driver initialization.
The amount of traffic generated by these packet drop traps is capped at
10Kpps to ensure the CPU is not overwhelmed by incoming packets.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discard trap groups are defined in a different enum so that they could
all share the same policer ID: MLXSW_REG_HTGT_TRAP_GROUP_MAX + 1.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the trap IDs used to report layer 2 drops.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches will add discard traps support in mlxsw. The driver
cannot configure such traps with a normal trap action, but needs to use
exception trap action, which also increments an error counter.
On the other hand, when these traps are initialized or set to drop
action, they should use the default drop action set by the firmware.
This guarantees that when the feature is disabled we get the exact same
behavior as before the feature was introduced.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now the action of a trap was never changed during its lifetime.
This is going to change by subsequent patches that will allow devlink to
control the action of certain traps.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tc transparently maps the software priority number to hardware. Update
it to pass the major priority which is what most drivers expect. Update
drivers too so they do not need to lshift the priority field of the
flow_cls_common_offload object. The stmmac driver is an exception, since
this code assumes the tc software priority is fine, therefore, lshift it
just to be conservative.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To identify timestamps for matching with their packets, Spectrum-1 uses a
five-tuple of (port, direction, domain number, message type, sequence ID).
If there are several clients from the same domain behind a single port
sending Delay_Req's, the only thing differentiating these packets, as far
as Spectrum-1 is concerned, is the sequence ID. Should sequence IDs between
individual clients be similar, conflicts may arise. That is not a problem
to hardware, which will simply deliver timestamps on a first comes, first
served basis.
However the driver uses a simple hash table to store the unmatched pieces.
When a new conflicting piece arrives, it pushes out the previously stored
one, which if it is a packet, is delivered without timestamp. Later on as
the corresponding timestamps arrive, the first one is mismatched to the
second packet, and the second one is never matched and eventually is GCd.
To correct this issue, instead of using a simple rhashtable, use rhltable
to keep the unmatched entries.
Previously, a found unmatched entry would always be removed from the hash
table. That is not the case anymore--an incompatible entry is left in the
hash table. Therefore removal from the hash table cannot be used to confirm
the validity of the looked-up pointer, instead the lookup would simply need
to be redone. Therefore move it inside the critical section. This
simplifies a lot of the code.
Fixes: 8748642751 ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Reported-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend existing driver for Spectrum and Spectrum-2 ASICs
to support Spectrum-3 ASIC as well.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e891ce1dd2 ("mlxsw: spectrum_buffers: Reduce pool size on
Spectrum-2"), pool size was reduced to mitigate a problem in port buffer
usage of ports split four ways. It turns out that this work around does not
solve the issue, and a further reduction is required.
Thus reduce the size of pool 0 by another 2.7 MiB, and round down to the
whole number of cells.
Fixes: e891ce1dd2 ("mlxsw: spectrum_buffers: Reduce pool size on Spectrum-2")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of sp2 pci driver registration fail, fix the error path to
start with sp1 pci driver unregister.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently are duplicated checks on orig_egr_types which are
redundant, I believe this is a typo and should actually be
orig_ing_types || orig_egr_types instead of the expression
orig_egr_types || orig_egr_types. Fix these.
Addresses-Coverity: ("Same on both sides")
Fixes: c6b36bdd04 ("mlxsw: spectrum_ptp: Increase parsing depth when PTP is enabled")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum systems have a configurable limit on how far into the packet they
parse. By default, the limit is 96 bytes.
An IPv6 PTP packet is layered as Ethernet/IPv6/UDP (14+40+8 bytes), and
sequence ID of a PTP event is only available 32 bytes into payload, for a
total of 94 bytes. When an additional 802.1q header is present as
well (such as when ptp4l is running on a VLAN port), the parsing limit is
exceeded. Such packets are not recognized as PTP, and are not timestamped.
Therefore generalize the current VXLAN-specific parsing depth setting to
allow reference-counted requests from other modules as well. Keep it in the
VXLAN module, because the MPRS register also configures UDP destination
port number used for VXLAN, and is thus closely tied to the VXLAN code
anyway.
Then invoke the new interfaces from both VXLAN (in obvious places), as well
as from PTP code, when the (global) timestamping configuration changes from
disabled to enabled or vice versa.
Fixes: 8748642751 ("mlxsw: spectrum: PTP: Support SIOCGHWTSTAMP, SIOCSHWTSTAMP ioctls")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Matching on reserved TCP flags bits is only supported using custom
parser. Since the usecase for that is not known now, just forbid to
offload rules that match on these bits.
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some matches and actions are not supported on egress. Track such rules
and forbid a bind of block which contains them to egress.
With this patch, the kernel tells the user he cannot do that:
$ tc qdisc add dev ens16np1 ingress_block 22 clsact
$ tc filter add block 22 protocol 802.1q pref 2 handle 101 flower vlan_id 100 skip_sw action pass
$ tc qdisc add dev ens16np2 egress_block 22 clsact
Error: mlxsw_spectrum: Block cannot be bound to egress because it contains unsupported rules.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum ASIC does not support redirection on egress, so refuse to
insert such flows:
$ tc qdisc add dev ens16np1 clsact
$ tc filter add dev ens16np1 egress protocol all pref 1 handle 101 flower skip_sw action mirred egress redirect dev ens16np2
Error: mlxsw_spectrum: Redirect action is not supported on egress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike IPv4, the kernel does not consolidate IPv6 nexthop groups. To
avoid exhausting the device's adjacency table - where nexthops are
stored - the driver does this consolidation instead.
Each nexthop group is hashed by XOR-ing the interface indexes of all the
member nexthop devices. However, the ifindex itself is not hashed, which
can result in identical keys used for different groups and finally an
-EBUSY error from rhashtable due to too long objects list.
Improve the situation by hashing the ifindex itself.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike Spectrum-1, the KVD (Key-value database) of Spectrum-2 is not
partitioned, so only expose the entire KVD size. This enables users to
query the total size of the KVD.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This object stores the flow block callbacks that are attached to this
block. Update flow_block_cb_lookup() to take this new object.
This patch restores the block sharing feature.
Fixes: da3eeb904f ("net: flow_offload: add list handling functions")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename this type definition and adapt users.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to annotate the netns on the flow block callback object,
flow_block_cb_is_busy() already checks for used blocks.
Fixes: d63db30c85 ("net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch periodically sends notifications about learned FDB entries.
Among other things, the notification includes the FID (Filtering
Identifier) and the port on which the MAC was learned.
In case the driver does not have the FID defined on the relevant port,
the following error will be periodically generated:
mlxsw_spectrum2 0000:06:00.0 swp32: Failed to find a matching {Port, VID} following FDB notification
This is not supposed to happen under normal conditions, but can happen
if an ingress tc filter with a redirect action is installed on a bridged
port. The redirect action will cause the packet's FID to be changed to
the dummy FID and a learning notification will be emitted with this FID
- which is not defined on the bridged port.
Fix this by having the driver ignore learning notifications generated
with the dummy FID and delete them from the device.
Another option is to chain an ignore action after the redirect action
which will cause the device to disable learning, but this means that we
need to consume another action whenever a redirect action is used. In
addition, the scenario described above is merely a corner case.
Fixes: cedbb8b259 ("mlxsw: spectrum_flower: Set dummy FID before forward action")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spectrum systems use DSCP rewrite map to update DSCP field in egressing
packets to correspond to priority that the packet has. Whether rewriting
will take place is determined at the point when the packet ingresses the
switch: if the port is in Trust L3 mode, packet priority is determined from
the DSCP map at the port, and DSCP rewrite will happen. If the port is in
Trust L2 mode, 802.1p is used for packet prioritization, and no DSCP
rewrite will happen.
The driver determines the port trust mode based on whether any DSCP
prioritization rules are in effect at given port. If there are any, trust
level is L3, otherwise it's L2. When the last DSCP rule is removed, the
port is switched to trust L2. Under that scenario, if DSCP of a packet
should be rewritten, it should be rewritten to 0.
However, when switching to Trust L2, the driver neglects to also update the
DSCP rewrite map. The last DSCP rule thus remains in effect, and packets
egressing through this port, if they have the right priority, will have
their DSCP set according to this rule.
Fix by first configuring the rewrite map, and only then switching to trust
L2 and bailing out.
Fixes: b2b1dab688 ("mlxsw: spectrum: Support ieee_setapp, ieee_delapp")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kvzalloc already zeroes the memory during the allocation.
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So the memset after these function is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And any other existing fields in this structure that refer to tc.
Specifically:
* tc_cls_flower_offload_flow_rule() to flow_cls_offload_flow_rule().
* TC_CLSFLOWER_* to FLOW_CLS_*.
* tc_cls_common_offload to tc_cls_common_offload.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a function to check if flow block callback is already in
use. Call this new function from flow_block_cb_setup_simple() and from
drivers.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates flow_block_cb_setup_simple() to use the flow block API.
Several drivers are also adjusted to use it.
This patch introduces the per-driver list of flow blocks to account for
blocks that are already in use.
Remove tc_block_offload alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_* and
remove temporary tcf_block_binder_type alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename from TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND and remove
temporary tc_block_command alias.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply by filling the PTP shaper parameters array.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting port up down event (PUDE), change the PTP shaper
configuration based on hardware time stamping on/off and the port's
speed.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get more accurate hardware time stamping, the driver needs to
enable PTP shaper on the port, for speeds lower than 40 Gbps.
Enable the PTP shaper on the port when the user turns on the hardware
time stamping, and disable it when the user turns off the hardware time
stamping.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New operation for getting the port's speed as part of port-type-speed
operations.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the PTP shaper parameters during the ptp_init(). For different
speeds, there are different parameters.
When the port's speed changes and PTP shaper is enabled, the firmware
changes the ETS shaper values according to the PTP shaper parameters for
this new speed.
The PTP shaper parameters array is left empty for now, will be filled in
a follow-up patch.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QPSC allows advanced configuration of the PTP shapers.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add note about disabling the PTP shaper when calling to
mlxsw_sp_port_ets_maxrate_set().
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP Shaper field is used for enabling and disabling of port-rate based
shaper which is slightly lower than port rate.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before mlxsw_sp1_ptp_packet_finish() sends the packet back, it validates
whether the corresponding port is still valid. However the condition is
incorrect: when mlxsw_sp_port == NULL, the code dereferences the port to
compare it to skb->dev.
The condition needs to check whether the port is present and skb->dev still
refers to that port (or else is NULL). If that does not hold, bail out.
Add a pair of parentheses to fix the condition.
Fixes: d92e4e6e33 ("mlxsw: spectrum: PTP: Support timestamping on Spectrum-1")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_ts_info callback is used for obtaining information about
timestamping capabilities of a network device. On Spectrum-1, implement
it to advertise the PHC and the capability to do HW timestamping, and
the supported RX and TX filters.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SIOCSHWTSTAMP ioctl configures HW timestamping on a given port.
Dispatch the ioctls to per-chip handler (which add to ptp_ops). Find
which PTP messages need to be timestamped and configure MTPPPC
accordingly.
The SIOCGHWTSTAMP ioctl is getter for the current configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configure MTPTPT to set which message types should arrive under which
PTP trap, and MOGCR to clear the timestamp queue after its contents are
reported through PTP_ING_FIFO or PTP_EGR_FIFO.
With this configuration, PTP packets start arriving through the PTP
traps. However since timestamping is disabled by default and there is
currently no way to enable it, they will not be timestamped.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamped PTP packets and the corresponding timestamps
need to be kept in caches until both are available, at which point they are
matched up and packets forwarded as appropriate. However, not all packets
will ever see their timestamp, and not all timestamps will ever see their
packet. It is therefore necessary to dispose of such abandoned entries.
To that end, introduce a garbage collector to collect entries that have
not had their counterpart turn up within about a second. The GC
maintains a monotonously-increasing value of GC cycle. Every entry that
is put to the hash table is annotated with the GC cycle at which it
should be collected. When the GC runs, it walks the hash table, and
collects the objects according to their GC cycle annotation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps arrive through a pair of dedicated events:
MLXSW_TRAP_ID_PTP_ING_FIFO and _EGR_FIFO. The payload delivered with
those traps is contents of the timestamp FIFO at a given port in a given
direction. Add a Spectrum-1-specific handler for these two events which
decodes the timestamps and forwards them to the PTP module.
Add a function that parses a packet, dispatching to ptp_classify_raw(),
and decodes PTP message type, domain number, and sequence ID. Add a new
mlxsw dependency on the PTP classifier.
Add helpers that can store and retrieve unmatched timestamps and SKBs to
the hash table added in a preceding patch.
Add the matching code itself: upon arrival of a timestamp or a packet,
look up the corresponding unmatched entry, and match it up. If there is
none, add a new unmatched entry. This logic is the same on ingress as on
egress.
Packets and timestamps that never matched need to be eventually disposed
of. A garbage collector added in a follow-up patch will take care of
that. Since currently all this code is turned off, no crud will
accumulate in the hash table.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now, the PTP hardware clock code was only invoked in the process
context (SYS_clock_adjtime -> do_clock_adjtime -> k_clock::clock_adj ->
pc_clock_adjtime -> posix_clock_operations::clock_adjtime ->
ptp_clock_info::adjtime -> mlxsw_spectrum).
In order to enable HW timestamping, which is tied into trap handling, it
will be necessary to take the clock lock from the PCI queue handler
tasklets as well.
Therefore use the _bh variants when handling the clock lock. Incidentally,
Documentation/ptp/ptp.txt recommends _irqsave variants, but that's
unnecessarily strong for our needs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two ptp_ops: init and fini, to initialize and finalize the PTP
subsystem. Call as appropriate from mlxsw_sp_init() and _fini().
Lay the groundwork for Spectrum-1 support. On Spectrum-1, the received
timestamped packets and their corresponding timestamps arrive
independently, and need to be matched up. Introduce the related data types
and add to struct mlxsw_sp_ptp_state the hash table that will keep the
unmatched entries.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps are delivered separately from the packets, and
need to paired up. Therefore, at some point after mlxsw_sp_port_xmit()
is invoked, it is necessary to involve the chip-specific driver code to
allow it to do the necessary bookkeeping and matching.
On Spectrum-2, timestamps are delivered in CQE. For that reason,
position the point of driver involvement into mlxsw_pci_cqe_sdq_handle()
to make it hopefully easier to extend for Spectrum-2 in the future.
To tell the driver what port the packet was sent on, keep tx_info
in SKB control buffer.
Introduce a new driver core interface mlxsw_core_ptp_transmitted(), a
driver callback ptp_transmitted, and a PTP op transmitted. The callee is
responsible for taking care of releasing the SKB passed to the new
interfaces, and correspondingly have the new stub callbacks just call
dev_kfree_skb_any().
Follow-up patches will introduce the actual content into
mlxsw_sp1_ptp_transmitted() in particular.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SKB control buffer is useful (and used) for bookkeeping of information
related to that SKB. Add helpers so that the mlxsw driver(s) can safely use
the buffer as well. The structure is currently empty, individual users will
add members to it as necessary.
Note that SKB allocation functions already clear the buffer, so the cleanup
is only necessary when ndo_start_xmit is called.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configured, the Spectrum hardware can recognize PTP packets and
trap them to the CPU using dedicated traps, PTP0 and PTP1.
One reason to get PTP packets under dedicated traps is to have a
separate policer suitable for the amount of PTP traffic expected when
switch is operated as a boundary clock. For this, add two new trap
groups, MLXSW_REG_HTGT_TRAP_GROUP_SP_PTP0 and _PTP1, and associate the
two PTP traps with these two groups.
In the driver, specifically for Spectrum-1, event PTP packets will need
to be paired up with their timestamps. Those arrive through a different
set of traps, added later in the patch set. To support this future use,
introduce a new PTP op, ptp_receive.
It is possible to configure which PTP messages should be trapped under
which PTP trap. On Spectrum systems, we will use PTP0 for event
packets (which need timestamping), and PTP1 for control packets (which
do not). Thus configure PTP0 trap with a custom callback that defers to
the ptp_receive op.
Additionally, L2 PTP packets are actually trapped through the LLDP trap,
not through any of the PTP traps. So treat the LLDP trap the same way as
the PTP0 trap. Unlike PTP traps, which are currently still disabled,
LLDP trap is active. Correspondingly, have all the implementations of
the ptp_receive op return true, which the handler treats as a signal to
forward the packet immediately.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Carry a chip-specific listener array in mlxsw_sp->listeners and
listeners_count. Register listeners from that array in
mlxsw_sp_traps_init(). Add a new listener array for Spectrum-1 traps and
configure the newly-added mlxsw_sp->listeners with this array.
The listener array is empty for now, the events will be added in a later
patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Extract out of mlxsw_sp_traps_init() a generic helper,
mlxsw_sp_traps_register(), and likewise with _unregister(). The new helpers
will later be called with Spectrum-1-specific traps.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register serves to configure global parameters of certain
monitoring operations. The following patches will use it to configure
that when PTP timestamps are delivered through the PTP FIFO traps, the
FIFO in question is cleared as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTPPTR is used for reading the per port PTP timestamp FIFO.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is used for configuring under which trap to deliver PTP
packets depending on type of the packet.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register serves for configuration of which PTP messages should be
timestamped. This is a global configuration, despite the register name.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend macros MLXSW_REG_MTMP_TEMP_TO_MC() to allow support of negative
temperature readout, since chip and others thermal components are
capable of operating within the negative temperature.
With no such support negative temperature will be consider as very high
temperature and it will cause wrong readout and thermal shutdown.
For negative values 2`s complement is used.
Tested in chamber.
Example of chip ambient temperature readout with chamber temperature:
-10 Celsius:
temp1: -6.0C (highest = -5.0C)
-5 Celsius:
temp1: -1.0C (highest = -1.0C)
v2 (Andrew Lunn):
* Replace '%u' with '%d' in mlxsw_hwmon_module_temp_show()
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When multiple sensors are mapped to the same cooling device, the
cooling device should be set according the worst sensor from the
sensors associated with this cooling device.
Provide the hottest thermal zone detection and enforce cooling device
to follow the temperature trends of the hottest zone only.
Prevent competition for the cooling device control from others zones,
by "stable trend" indication. A cooling device will not perform any
actions associated with a zone with a "stable trend".
When other thermal zone is detected as a hottest, a cooling device is
to be switched to following temperature trends of new hottest zone.
Thermal zone score is represented by 32 bits unsigned integer and
calculated according to the next formula:
For T < TZ<t><i>, where t from {normal trip = 0, high trip = 1, hot
trip = 2, critical = 3}:
TZ<i> score = (T + (TZ<t><i> - T) / 2) / (TZ<t><i> - T) * 256 ** j;
Highest thermal zone score s is set as MAX(TZ<i>score);
Following this formula, if TZ<i> is in trip point higher than TZ<k>,
the higher score is to be always assigned to TZ<i>.
For two thermal zones located at the same kind of trip point, the higher
score will be assigned to the zone which is closer to the next trip
point. Thus, the highest score will always be assigned objectively to
the hottest thermal zone.
All the thermal zones initially are to be configured with mode
"enabled" with the "step_wise" governor.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dedicated thermal zone for each inter-connect device. The
current temperature is obtained from inter-connect temperature sensor
and the default trip points are set to the same values as default ASIC
trip points. These settings could be changed from the user space.
A cooling device (fan) is bound to all inter-connect devices.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the previously extended flow_dissector infrastructure and
offload matching on ingress port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the size of the SRC_SYS_PORT element to be 16.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX_ACL_SYSTEM_PORT is 8 bit but SRC_SYS_PORT is 16 bits. Internally,
SRC_SYS_PORT is used to carry the value. Relax the checker in case of
RX_ACL_SYSTEM_PORT and allow different size.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RX_ACL_SYSTEM_PORT is equal to SRC_SYS_PORT - 1. So before write to
block we need to adjust the key value. Introduce new "EXT" helper to
implement this.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both listeners - mlxsw and netdevsim - of IPv6 FIB notifications are now
ready to handle IPv6 multipath notifications.
Therefore, stop ignoring such notifications in both drivers and stop
sending notification for each added / deleted nexthop.
v2:
* Remove 'multipath_rt' from 'struct fib6_entry_notifier_info'
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the driver to create an IPv6 multipath route in one go by passing
an array of sibling routes and iterating over them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the functions that take care of populating IPv6 nexthop
groups only add / delete a single nexthop.
Prepare them to handle multiple routes in one notification by passing an
array of routes and adding / deleting all of them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the driver to handle multiple routes in a single notification by
passing an array of routes to the functions that actually add / delete a
route.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, IPv6 replace notifications were only sent from
fib6_add_rt2node(). The function only emitted such notifications if a
route actually replaced another route.
A previous patch added another call site in ip6_route_multipath_add()
from which such notification can be emitted even if a route was merely
added and did not replace another route.
Adjust the driver to take this into account and potentially set the
'replace' flag to 'false' if the notified route did not replace an
existing route.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the driver to process IPv6 multipath notifications by passing an
array of 'struct fib6_info' instead of just one route.
A reference is taken on each sibling route in order to prevent them from
being freed until they are processed by the workqueue.
v2:
* Remove 'multipath_rt' usage
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function mlxsw_sp_router_fib6_event() takes care of preparing the
needed information for the work item that actually inserts the route
into the device.
When processing an IPv6 multipath route, the function will need to
allocate an array to store pointers to all the sibling routes.
Change the function's signature to return an error code and adjust the
single call site.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No such notifications are sent by the IPv6 code, so remove them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 multipath notifications are about to be sent, but mlxsw is not
ready to process them, so ignore them.
The limitation will be lifted by a subsequent patch which will also stop
the kernel from sending a notification for each nexthop.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Compilation on 32-bit ARM fails after commit 992aa864dc ("mlxsw:
spectrum_ptp: Add implementation for physical hardware clock operations")
because of 64-bit division:
arm-linux-gnueabi-ld:
drivers/net/ethernet/mellanox/mlxsw/spectrum_ptp.o: in function
`mlxsw_sp1_ptp_phc_settime': spectrum_ptp.c:(.text+0x39c): undefined
reference to `__aeabi_uldivmod'
Fix by using div_u64().
Fixes: 992aa864dc ("mlxsw: spectrum_ptp: Add implementation for physical hardware clock operations")
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTPPS register provides the device PPS capabilities, configure the PPS
in and out modules and holds the PPS in time stamp.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MTUTC register configures the HW UTC counter.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Query free running clock PCI BAR and offsets during the pci_init.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new bus operations for reading the hardware free running clock.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add free running clock PCI BAR and offset to query firmware command.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PVID is removed from a bridge port, the Linux bridge drops both
untagged and prio-tagged packets. Align mlxsw with this behavior.
Fixes: 148f472da5 ("mlxsw: reg: Add the Switch Port Acceptable Frame Types register")
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an issue on Spectrum-2, in front-panel ports split four ways, 2 out
of 32 port buffers cannot be used. To work around this, the next FW release
will mark them as unused, and will report correspondingly lower total
shared buffer size. mlxsw will pick up the new value through a query to
cap_total_buffer_size resource. However the initial size for shared buffer
pool 0 is hard-coded and therefore needs to be updated.
Thus reduce the pool size by 2.7 MiB (which corresponds to 2/32 of the
total size of 42 MiB), and round down to the whole number of cells.
Fixes: fe099bf682 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TOS value was not extracted correctly. Fix it.
Fixes: 87996f91f7 ("mlxsw: spectrum_flower: Add support for ip tos")
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver tries to periodically refresh neighbours that are used to
reach nexthops. This is done by periodically calling neigh_event_send().
However, if the neighbour becomes dead, there is nothing we can do to
return it to a connected state and the above function call is basically
a NOP.
This results in the nexthop never being written to the device's
adjacency table and therefore never used to forward packets.
Fix this by dropping our reference from the dead neighbour and
associating the nexthop with a new neigbhour which we will try to
refresh.
Fixes: a7ff87acd9 ("mlxsw: spectrum_router: Implement next-hop routing")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same hash function and seed are used for both ECMP and LAG hash.
Therefore, when a LAG device is used as a nexthop device as part of an
ECMP group, hash polarization can occur and all the traffic will be
hashed to a single LAG slave.
Fix this by using a different seed for the LAG hash.
Fixes: fa73989f26 ("mlxsw: spectrum: Use a stable ECMP/LAG seed")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fail attempts to use nexthop objects with routes until support can be
properly added.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helpers to access fib_nh and fib_nhs fields of a fib_info. Drop the
fib_dev macro which is an alias for the first nexthop. Replacements:
fi->fib_dev --> fib_info_nh(fi, 0)->fib_nh_dev
fi->fib_nh --> fib_info_nh(fi, 0)
fi->fib_nh[i] --> fib_info_nh(fi, i)
fi->fib_nhs --> fib_info_num_path(fi)
where fib_info_nh(fi, i) returns fi->fib_nh[nhsel] and fib_info_num_path
returns fi->fib_nhs.
Move the existing fib_info_nhc to nexthop.h and define the new ones
there. A later patch adds a check if a fib_info uses a nexthop object,
and defining the helpers in nexthop.h avoid circular header
dependencies.
After this all remaining open coded references to fi->fib_nhs and
fi->fib_nh are in:
- fib_create_info and helpers used to lookup an existing fib_info
entry, and
- the netdev event functions fib_sync_down_dev and fib_sync_up.
The latter two will not be reused for nexthops, and the fib_create_info
will be updated to handle a nexthop in a fib_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement mlxfw status_notify op by passing notification down to
devlink. Also notify about flash update begin and end.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the error messages are printed to dmesg. Propagate them also
to directly to user doing the flashing through extack.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Benefit from the devlink flash update implementation and ethtool
fallback to it and move firmware flash implementation there.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
Obtain SFP modules temperatures through MTMP register instead of MTBR
register, because the first one utilizes shorter transaction buffer size
for request. It improves performance in case low frequency interface
(I2C) is used for communication with a chip.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend sensor index size for Management Temperature Bulk Register
(MTBR) and Management Temperature Register (MTMP) upto 12 bits in
order to align registers description with new version of PRM document.
Add define for base sensor index for SFP modules temperature reading
for MTMP register.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add new attributes to hwmon object for exposing inter-connects temperature
input, highest, reset_history temperatures and label. Temperatures are read
from Management Temperature Register.
The number of inter-connect devices is read from Management General
Peripheral Information Register.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MGPIR - Management General Peripheral Information Register, which
allows software to query the hardware and firmware general information
of peripheral entities as Gearboxes etc.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the size of sensor_index field of MTMP (Management Temperature
Register), from 8 to 12 bits due to hardware change.
Add define for sensor index for Gear Box (inter-connects) temperature
reading.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core first registers with the hwmon and thermal subsystems
and only then proceeds to initialize the switch driver (e.g.,
mlxsw_spectrum). It is only during the last stage that the current
firmware version is validated and a newer one flashed, if necessary.
The above means that if a new firmware feature is utilized by the
hwmon/thermal code, the driver will not be able to load.
Solve this by re-ordering initializing the switch driver before
registering with the hwmon and thermal subsystems.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current implementation uses fixed size of I2C data transaction buffer.
Allow to set size of I2C transactions according to I2C physical adapter
capability. For that purpose adapter read and write size is obtained
from the I2C physical adapter and buffer size is set according to the
minimum of these two values. If adapter does not provide such info,
default buffer size is to be used.
It allows to improve performance of I2C access to silicon when long
size transactions are used.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend initialization flow with query request for firmware info in
order to obtain firmware version info.
This info is to be provided to minimal driver to support ethtool
get_drvinfo() interface.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Force of 56G is not supported by hardware in Ethernet devices. This
configuration fails with a bad parameter error from firmware.
Add check of this case. Instead of trying to set 56G with autoneg off,
return a meaningful error.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When identical rules are inserted, the latter one goes to C-TCAM. For
that, a second eRP with the same mask is created. These 2 eRPs by the
nature cannot be merged and also one cannot be parent of another.
Teach mlxsw_sp_acl_erp_delta_fill() about this possibility and handle it
gracefully.
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Fixes: c22291f7cf ("mlxsw: spectrum: acl: Implement delta for ERP")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move fib6_nh to the end of fib6_info and make it an array of
size 0. Pass a flag to fib6_info_alloc indicating if the
allocation needs to add space for a fib6_nh.
The current code path always has a fib6_nh allocated with a
fib6_info; with nexthop objects they will be separate.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are series of patches that add SPDX tags to different kernel files,
based on two different things:
- SPDX entries are added to a bunch of files that we missed a year ago
that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the last
big sweep, or they were Makefile/Kconfig files, which we didn't
touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the next
few weeks as the tools and reviewers crunch through the more "odd"
variants of how to say "GPLv2" that developers have come up with over
the years, combined with other fun oddities (GPL + a BSD disclaimer?)
that are being unearthed, with the goal for the whole kernel to be
cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXOP8uw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynmGQCgy3evqzleuOITDpuWaxewFdHqiJYAnA7KRw4H
1KwtfRnMtG6dk/XaS7H7
=O9lH
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull SPDX update from Greg KH:
"Here is a series of patches that add SPDX tags to different kernel
files, based on two different things:
- SPDX entries are added to a bunch of files that we missed a year
ago that do not have any license information at all.
These were either missed because the tool saw the MODULE_LICENSE()
tag, or some EXPORT_SYMBOL tags, and got confused and thought the
file had a real license, or the files have been added since the
last big sweep, or they were Makefile/Kconfig files, which we
didn't touch last time.
- Add GPL-2.0-only or GPL-2.0-or-later tags to files where our scan
tools can determine the license text in the file itself. Where this
happens, the license text is removed, in order to cut down on the
700+ different ways we have in the kernel today, in a quest to get
rid of all of these.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers.
The reason for these "large" patches is if we were to continue to
progress at the current rate of change in the kernel, adding license
tags to individual files in different subsystems, we would be finished
in about 10 years at the earliest.
There will be more series of these types of patches coming over the
next few weeks as the tools and reviewers crunch through the more
"odd" variants of how to say "GPLv2" that developers have come up with
over the years, combined with other fun oddities (GPL + a BSD
disclaimer?) that are being unearthed, with the goal for the whole
kernel to be cleaned up.
These diffstats are not small, 3840 files are touched, over 10k lines
removed in just 24 patches"
* tag 'spdx-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (24 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 25
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 24
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 23
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 22
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 21
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 20
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 19
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 18
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 17
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 15
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 14
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 13
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 12
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 11
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 10
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 9
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 7
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 5
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 4
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 3
...
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
1) Use after free in __dev_map_entry_free(), from Eric Dumazet.
2) Fix TCP retransmission timestamps on passive Fast Open, from Yuchung
Cheng.
3) Orphan NFC, we'll take the patches directly into my tree. From
Johannes Berg.
4) We can't recycle cloned TCP skbs, from Eric Dumazet.
5) Some flow dissector bpf test fixes, from Stanislav Fomichev.
6) Fix RCU marking and warnings in rhashtable, from Herbert Xu.
7) Fix some potential fib6 leaks, from Eric Dumazet.
8) Fix a _decode_session4 uninitialized memory read bug fix that got
lost in a merge. From Florian Westphal.
9) Fix ipv6 source address routing wrt. exception route entries, from
Wei Wang.
10) The netdev_xmit_more() conversion was not done %100 properly in mlx5
driver, fix from Tariq Toukan.
11) Clean up botched merge on netfilter kselftest, from Florian
Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (74 commits)
of_net: fix of_get_mac_address retval if compiled without CONFIG_OF
net: fix kernel-doc warnings for socket.c
net: Treat sock->sk_drops as an unsigned int when printing
kselftests: netfilter: fix leftover net/net-next merge conflict
mlxsw: core: Prevent reading unsupported slave address from SFP EEPROM
mlxsw: core: Prevent QSFP module initialization for old hardware
vsock/virtio: Initialize core virtio vsock before registering the driver
net/mlx5e: Fix possible modify header actions memory leak
net/mlx5e: Fix no rewrite fields with the same match
net/mlx5e: Additional check for flow destination comparison
net/mlx5e: Add missing ethtool driver info for representors
net/mlx5e: Fix number of vports for ingress ACL configuration
net/mlx5e: Fix ethtool rxfh commands when CONFIG_MLX5_EN_RXNFC is disabled
net/mlx5e: Fix wrong xmit_more application
net/mlx5: Fix peer pf disable hca command
net/mlx5: E-Switch, Correct type to u16 for vport_num and int for vport_index
net/mlx5: Add meaningful return codes to status_to_err function
net/mlx5: Imply MLXFW in mlx5_core
Revert "tipc: fix modprobe tipc failed after switch order of device registration"
vsock/virtio: free packets during the socket release
...
Prevent reading unsupported slave address from SFP EEPROM by testing
Diagnostic Monitoring Type byte in EEPROM. Read only page zero of
EEPROM, in case this byte is zero.
If some SFP transceiver does not support Digital Optical Monitoring
(DOM), reading SFP EEPROM slave address 0x51 could return an error.
Availability of DOM support is verified by reading from zero page
Diagnostic Monitoring Type byte describing how diagnostic monitoring is
implemented by transceiver. If bit 6 of this byte is set, it indicates
that digital diagnostic monitoring has been implemented. Otherwise it is
not and transceiver could fail to reply to transaction for slave address
0x51 [1010001X (A2h)], which is used to access measurements page.
Such issue has been observed when reading cable MCP2M00-xxxx,
MCP7F00-xxxx, and few others.
Fixes: 2ea109039c ("mlxsw: spectrum: Add support for access cable info via ethtool")
Fixes: 4400081b63 ("mlxsw: spectrum: Fix EEPROM access in case of SFP/SFP+")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old Mellanox silicons, like switchx-2, switch-ib do not support reading
QSFP modules temperature through MTMP register. Attempt to access this
register on systems equipped with the this kind of silicon will cause
initialization flow failure.
Test for hardware resource capability is added in order to distinct
between old and new silicon - old silicons do not have such capability.
Fixes: 6a79507cfe ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Fixes: 5c42eaa07b ("mlxsw: core: Extend hwmon interface with QSFP module temperature attributes")
Reported-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal management updates from Zhang Rui:
- Remove the 'module' Kconfig option for thermal subsystem framework
because the thermal framework are required to be ready as early as
possible to avoid overheat at boot time (Daniel Lezcano)
- Fix a bug that thermal framework pokes disabled thermal zones upon
resume (Wei Wang)
- A couple of cleanups and trivial fixes on int340x thermal drivers
(Srinivas Pandruvada, Zhang Rui, Sumeet Pawnikar)
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
drivers: thermal: processor_thermal: Downgrade error message
mlxsw: Remove obsolete dependency on THERMAL=m
hwmon/drivers/core: Simplify complex dependency
thermal/drivers/core: Fix typo in the option name
thermal/drivers/core: Remove depends on THERMAL in Kconfig
thermal/drivers/core: Remove module unload code
thermal/drivers/core: Remove the module Kconfig's option
thermal: core: skip update disabled thermal zones after suspend
thermal: make device_register's type argument const
thermal: intel: int340x: processor_thermal_device: simplify to get driver data
thermal/int3403_thermal: favor _TMP instead of PTYP
The THERMAL configuration option was changed from tristate to bool, but
a dependency on THERMAL=m was forgotten, leading to a warning when
running "make savedefconfig":
boolean symbol THERMAL tested for 'm'? test forced to 'n'
Fixes: be33e4fbbea581ea ("thermal/drivers/core: Remove the module Kconfig's option")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Allow user to enable loopback feature for individual ports using ethtool.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPLR register allows configuration of the port's loopback mode.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Updates the Mellanox spectrum driver to use the newer intermediate
representation for flow actions in matchall offloads.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When splitting a port, different local ports need to be mapped on different
systems. For example:
SN3700 (local_ports_in_2x=2):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 5
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 3
front panel 2 --> local port 5
SN3800 (local_ports_in_2x=1):
* Without split:
front panel 1 --> local port 1
front panel 2 --> local port 3
* Split to 2:
front panel 1s0 --> local port 1
front panel 1s1 --> local port 2
front panel 2 --> local port 3
The local_ports_in_{1x, 2x} resources provide the offsets from the base
local ports according to which the new local ports can be calculated.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the number of local ports in 4x changed between SPC and SPC-2,
firmware expose new resources that the driver can query.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new version supports two features that are required by upcoming
changes in the driver:
* Querying of new resources allowing port split into two ports on
Spectrum-2 systems
* Querying of number of gearboxes on supported systems such as SN3800
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlxsw currently does not support v6 gateways with v4 routes. Commit
19a9d136f1 ("ipv4: Flag fib_info with a fib_nh using IPv6 gateway")
prevents a route from being added, but nothing stops the replace or
append. Add a catch for them too.
$ ip ro add 172.16.2.0/24 via 10.99.1.2
$ ip ro replace 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
$ ip ro append 172.16.2.0/24 via inet6 fe80::202:ff:fe00:b dev swp1s0
Error: mlxsw_spectrum: IPv6 gateway with IPv4 route is not supported.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch the CPU port to use the new dedicated egress pool instead the
previously used egress pool which was shared with normal front panel
ports.
Add per-port quotas for the amount of traffic that can be buffered for
the CPU port and also adjust the per-{port, TC} quotas.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPU port is used to transmit traffic that is trapped to the host
CPU. It is therefore irrelevant to define ingress quota for it.
Add a 'skip_ingress' argument to the function tasked with configuring
per-port quotas, so that ingress quotas could be skipped in case the
passed local port is the CPU port.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is used to set the per-port shared buffer quotas.
Currently, these quotas are only set for front panel ports, but a
subsequent patch will configure these quotas for the CPU port as well.
The configuration required for the CPU port is a bit different than that
of the front panel ports, so split the business logic into a separate
function which will be called with different parameters for the CPU
port.
No functional changes intended.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new ingress pool that was added in the previous patch for
control packets (e.g., STP, LACP) that are trapped to the CPU.
The previous management pool is no longer necessary and therefore its
size is set to 0.
The maximum quota for traffic towards the CPU is increased to 50% of the
free space in the new ingress pool and therefore the reserved space is
reduced by half, to 10KB - in both the shared and headroom buffer. This
allows for more efficient utilization of the shared buffer as reserved
space cannot be used for other purposes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets that are trapped to the CPU are transmitted through the CPU port
to the attached host. The CPU port is therefore like any other port and
needs to have shared buffer configuration.
The maximum quotas configured for the CPU are provided using dynamic
threshold and cannot be changed by the user. In order to make sure that
these thresholds are always valid, the configuration of the threshold
type of these pools is forbidden.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently assumes that ingress pools have lower indices than
egress pools. This makes it impossible to add more ingress pools
without breaking user configuration that relies on a certain pool index
to correspond to an egress pool.
Remove such assumptions from the code, so that more ingress pools could
be added by subsequent patches.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e83c045e53 ("mlxsw: spectrum_buffers: Configure MC pool")
configured the threshold of the multicast TCs as infinite so that the
admission of multicast packets is only depended on per-switch priority
threshold.
Forbid the user from changing the thresholds of these multicast TCs and
their binding to a different pool.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Multicast packets have three egress quotas:
* Per egress port
* Per egress port and traffic class
* Per switch priority
The limits on the switch priority are not exposed to the user and
specified as dynamic threshold on the first egress pool.
Forbid changing the threshold type of the first egress pool so that
these limits are always valid.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e83c045e53 ("mlxsw: spectrum_buffers: Configure MC pool") added
a dedicated pool for multicast traffic. The pool is visible to the user
so that it would be possible to monitor its occupancy, but its
configuration should be forbidden in order to maintain its intended
operation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to need to veto changes in certain TCs'
binding and threshold configurations.
Add fields to the TC's struct that indicate if the TC can be bound to a
different pool and whether its threshold can change and enforce that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Subsequent patches are going to need to veto changes in certain pools'
size and / or threshold type (mode).
Add two fields to the pool's struct that indicate if either of these
attributes is allowed to change and enforce that.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pool indices are currently hard coded throughout the code, which
makes the code hard to follow and extend.
Overcome this by using defines for the pool indices.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add extack to shared buffer set operations, so that meaningful error
messages could be propagated to the user.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTF_ADDRCONF flag filters out routes added by RA's in determining
which routes can be appended to an existing one to create a multipath
route. Restore the flag check and add a comment to document the RA piece.
Fixes: 4e54507ab1 ("ipv6: Simplify rt6_qualify_for_ecmp")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c7a1ce397a ("ipv6: Change addrconf_f6i_alloc to use
ip6_route_info_create"), the gateway is no longer filled in for fib6_nh
structs in a prefix route. Accordingly, the RTF_ADDRCONF flag check can
be dropped from the 'rt6_qualify_for_ecmp'.
Further, RTF_DYNAMIC is only set in rt6_info instances, so it can be
removed from the check as well.
This reduces rt6_qualify_for_ecmp and the mlxsw version to just checking
if the nexthop has a gateway which is the real indication of whether
entries can be coalesced into a multipath route.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlxsw does not support policy-based routing (PBR) and
therefore forbids the installation of non-default FIB rules except for
the l3mdev rule which is used for VRFs.
Relax the check to allow the installation of FIB rules that would never
match packets received by the device. Specifically, if the iif is that
of the loopback netdev. This is useful for users that need to redirect
locally generated packets based on FIB rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to get a consistent behavior of traffic flows across reboots /
module unload, we need to use the same ECMP/LAG seed.
Calculate the seed by hashing the base MAC of the device. This results
in a seed that is both unique (to avoid polarization) and consistent.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit f6b19b354d ("net: devlink: select NET_DEVLINK
from drivers") adds implicit select of NET_DEVLINK for
mlxsw, the code does not have to deal with the case
when CONFIG_NET_DEVLINK is not enabled. So remove the ifcase
and adjust Makefile.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If link is down and autoneg is set to on/off, the status in ethtool does
not change.
The reason is when the link is down the function returns with zero
before changing autoneg value.
Move the checking of link state (up/down) to be performed after setting
autoneg value, in order to be sure that autoneg will change in any case.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During driver initialization the driver sends a reset to the device and
waits for the firmware to signal that it is ready to continue.
Commit d2f372ba09 ("mlxsw: pci: Increase PCI SW reset timeout")
increased the timeout to 13 seconds due to longer PHY calibration in
Spectrum-2 compared to Spectrum-1.
Recently it became apparent that this timeout is too short and therefore
this patch increases it again to a safer limit that will be reduced in
the future.
Fixes: c3ab435466 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Fixes: d2f372ba09 ("mlxsw: pci: Increase PCI SW reset timeout")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both Spectrum-1 and Spectrum-2 chips are currently configured such that
pairs of TC n (which is used for UC traffic) and TC n+8 (which is used
for MC traffic) are feeding into the same subgroup. Strict
prioritization is configured between the two TCs, and by enabling
MC-aware mode on the switch, the lower-numbered (UC) TCs are favored
over the higher-numbered (MC) TCs.
On Spectrum-2 however, there is an issue in configuration of the
MC-aware mode. As a result, MC traffic is prioritized over UC traffic.
To work around the issue, configure the MC TCs with DWRR mode (while
keeping the UC TCs in strict mode).
With this patch, the multicast-unicast arbitration results in the same
behavior on both Spectrum-1 and Spectrum-2 chips.
Fixes: 7b81953066 ("mlxsw: spectrum: Configure MC-aware mode on mlxsw ports")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to routes and FDB entries, the neighbour table is
reflected to the device.
Set an offload indication on the neighbour in case it was programmed to
the device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Next patch will add offload indication to neighbours, but the indication
should only be altered in case the neighbour was successfully added to /
deleted from the device.
Propagate neighbour update errors, so that they could be taken into
account by the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Spectrum-1, when a multicast packet is admitted to the shared buffer
it increases the quotas of all the ports and {port, TC} to which it is
forwarded to.
The above means that multicast packets are accounted multiple times in
the shared buffer and can therefore cause the associated shared buffer
pool to fill up very quickly.
To work around this issue, commit e83c045e53 ("mlxsw:
spectrum_buffers: Configure MC pool") added a dedicated multicast pool
in which multicast packets are accounted.
The issue is not present in Spectrum-2, but in order to be backward
compatible with Spectrum-1, its default behavior is to allow a multicast
packet to increase multiple egress quotas instead of one.
Until the new (non-backward compatible) mode is supported, configure a
dedicated multicast pool as in Spectrum-1.
Fixes: fe099bf682 ("mlxsw: spectrum_buffers: Add Spectrum-2 shared buffer configuration")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC
addresses") enabled the driver to veto router interface (RIF) MAC
addresses that it cannot support.
This check should only be performed for interfaces for which the driver
actually configures a RIF. A VRF upper is not one of them, so ignore it.
Without this patch it is not possible to set an IP address on the VRF
device and use it as a loopback.
Fixes: 74bc993974 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Tested-by: Alexander Petrovskiy <alexpe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue is used to periodically update the networking stack about
activity / statistics of various objects such as neighbours and TC
actions.
It should not be called as part of memory reclaim path, so remove the
WQ_MEM_RECLAIM flag.
Fixes: 3d5479e920 ("mlxsw: core: Remove deprecated create_workqueue")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The EMAD workqueue is used to handle retransmission of EMAD packets that
contain configuration data for the device's firmware.
Given the workers need to allocate these packets and that the code is
not called as part of memory reclaim path, remove the WQ_MEM_RECLAIM
flag.
Fixes: d965465b60 ("mlxsw: core: Fix possible deadlock")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose the following ASIC information via devlink info command:
- Driver name
- Hardware revision
- Firmware PSID
- Running firmware version
Standard output example:
$ devlink dev info pci/0000:03:00.0
pci/0000:03:00.0:
driver mlxsw_spectrum
versions:
fixed:
hw.revision A0
fw.psid MT_2750110033
running:
fw.version 13.1910.622
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add MGIR register. MGIR, Management General Information Register, allows
software to query the hardware and firmware general information.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until support is added to the offload drivers, they need to be able to
reject routes with an IPv6 gateway. To that end add a flag to fib_info
that indicates if any fib_nh has a v6 gateway. The flag allows the drivers
to efficiently know the use of a v6 gateway without walking all fib_nh
tied to a fib_info each time a route is added.
Update mlxsw and rocker to reject the routes with extack message as to why.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for an IPv6 gateway to rtable. Since a gateway is either
IPv4 or IPv6, make it a union with rt_gw4 where rt_gw_family decides
which address is in use.
When dumping the route data, encode an ipv6 nexthop using RTA_VIA.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow the gateway to be either an IPv4 or IPv6 address, remove
rt_uses_gateway from rtable and replace with rt_gw_family. If
rt_gw_family is set it implies rt_uses_gateway. Rename rt_gateway
to rt_gw4 to represent the IPv4 version.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the gateway in a fib_nh_common to be from a different address
family than the outer fib{6}_nh. To that end, replace nhc_has_gw with
nhc_gw_family and update users of nhc_has_gw to check nhc_gw_family.
Now nhc_family is used to know if the nh_common is part of a fib_nh
or fib6_nh (used for container_of to get to route family specific data),
and nhc_gw_family represents the address family for the gateway.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Obtain HW id and pass it down to mlxsw_core_port_init() as it would be
used as switch_id in devlink and exposed to user.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove implementation of get_port_parent_id ndo and rely on core calling
into devlink for the information directly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass the switch ID down the to devlink through devlink_port_attrs_set()
so it can be used by devlink_compat_switch_id_get().
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend devlink_port_attrs_set() to pass switch ID for ports which are
part of switch and store it in port attrs. For other ports, this is
NULL.
Note that this allows the driver to group devlink ports into one or more
switches according to the actual topology.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The name of the trace is no longer correct, since there is no disable of
rehash done. So name it "rehash_rollback_failed".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if a rollback ends with error, the vregion is in a zombie
state until end of the existence. Instead of that, rather try to
continue where rollback ended later on (after rehash interval).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the call of rehash_dis trace and the error message to
vregion_migrate() next to the failed_rollback flag set.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flag is set by the caller mlxsw_sp_acl_tcam_vregion_migrate() anyway,
so don't set it here.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib6_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, gateway, flags, and lwtstate are common
with all nexthop definitions. In some places new temporary variables
are declared or local variables renamed to maintain line lengths.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename fib_nh entries that will be moved to a fib_nh_common struct.
Specifically, the device, oif, gateway, flags, scope, lwtstate,
nh_weight and nh_upper_bound are common with all nexthop definitions.
In the process shorten fib_nh_lwtstate to fib_nh_lws to avoid really
long lines.
Rename only; no functional change intended.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gateway setting is not per fib6_info entry but per-fib6_nh. Add a new
fib_nh_has_gw flag to fib6_nh and convert references to RTF_GATEWAY to
the new flag. For IPv6 address the flag is cheaper than checking that
nh_gw is non-0 like IPv4 does.
While this increases fib6_nh by 8-bytes, the effective allocation size of
a fib6_info is unchanged. The 8 bytes is recovered later with a
fib_nh_common change.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rely on the previously introduced fallback and let the core call
devlink directly in order to get the physical port name.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for devlink compat functions to work, implement
ndo_get_devlink_port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers are becoming more dependent on NET_DEVLINK being selected
in configuration. With upcoming compat functions, the behavior would be
wrong in case devlink was not compiled in. So make the drivers select
NET_DEVLINK and rely on the functions being there, not just stubs.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since attrs are static during the existence of devlink port, set the
before registration of the port.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recently added function in mlxsw triggers a harmless compiler warning:
In file included from drivers/net/ethernet/mellanox/mlxsw/core.h:17,
from drivers/net/ethernet/mellanox/mlxsw/core_env.c:7:
drivers/net/ethernet/mellanox/mlxsw/core_env.c: In function 'mlxsw_env_module_temp_thresholds_get':
drivers/net/ethernet/mellanox/mlxsw/reg.h:8015:45: error: '*' in boolean context, suggest '&&' instead [-Werror=int-in-bool-context]
#define MLXSW_REG_MTMP_TEMP_TO_MC(val) (val * 125)
~~~~~^~~~~~
drivers/net/ethernet/mellanox/mlxsw/core_env.c:116:8: note: in expansion of macro 'MLXSW_REG_MTMP_TEMP_TO_MC'
if (!MLXSW_REG_MTMP_TEMP_TO_MC(module_temp)) {
^~~~~~~~~~~~~~~~~~~~~~~~~
The warning is normally disabled, but it would be nice to enable
it to find real bugs, and there are no other known instances at
the moment.
Replace the negation with a zero-comparison, which also matches
the comment above it.
Fixes: d93c19a1d9 ("mlxsw: core: Add API for QSFP module temperature thresholds reading")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently base_mac is not initialized which causes wrong reporting of
zeroed parent_id to userspace. Fix this by initializing base_mac
properly.
Fixes: c100e47caa ("mlxsw: minimal: Add ethtool support")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Verify during thermal initialization if QSFP module's entry is already
configured in order to prevent duplication.
Such scenario could happen in case two switch drivers (PCI and I2C
based) coexist and if after boot, splitting configuration is applied
for some ports and then I2C based driver is re-probed.
In such case after reboot same QSFP module, associated with split will
be discovered by I2C based driver few times, and it will cause a crash.
It could happen for example on system equipped with BMC (Baseboard
Management Controller), running I2C based driver, when the next steps
are performed:
- System boot
- Host side configures port spilt.
- BMC side is rebooted.
Fixes: 6a79507cfe ("mlxsw: core: Extend thermal module with per QSFP module thermal zones")
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch to bitmap_zalloc() to show clearly what we are allocating.
Besides that it returns pointer of bitmap type instead of opaque void *.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend initialization flow by query requests for chip resources data in
order to obtain chip's specific capabilities, like the number of ports.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend input parameters list of command API in mlxsw_i2c_cmd() in order
to support initialization commands. Up until now, only access commands
were supported by I2C driver.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change input parameter name "resource" to "res" in mlxsw_i2c_init() in
order to align it with mlxsw_pci_init().
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move mlxsw_pci_resources_query() to a common location to allow reuse by
the different drivers and over all the supported physical buses. Rename
it to mlxsw_core_resources_query().
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The minimal driver is chip independent and uses I2C bus for chip access.
Its purpose is to support chassis management on systems equipped with
Mellanox switch ASICs. For example from BMC (Board Management
Controller) device.
Expose a dummy netdev for each front panel port and implement basic
ethtool operations to obtain QSFP/SFP module info through ethtool.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace "mlxsw_minimal" by "mlxsw_m" in order to improve code
readability.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the implementation of ethtool module callbacks - .get_module_info()
and .get_module_eeprom() - to a common location to allow reuse by the
different mlxsw drivers.
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The return value is ignored anyway, so just return void.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shalom Toledo