This patch adds a new LED trigger that LED device can configure
to employ software or hardware pattern engine.
Consumers can write 'pattern' file to enable the software pattern
which alters the brightness for the specified duration with one
software timer.
Moreover consumers can write 'hw_pattern' file to enable the hardware
pattern for some LED controllers which can autonomously control
brightness over time, according to some preprogrammed hardware
patterns.
Signed-off-by: Raphael Teysseyre <rteysseyre@gmail.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
All the triggers are defined in a big if LEDS_TRIGGERS...endif block.
So there is no need to let each driver depend on LEDS_TRIGGERS explicitly
once more.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This commit introduces a NETDEV trigger for named device
activity. Available triggers are link, rx, and tx.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Fixes: 7df4f9a9f0 ("leds: ledtrig-activity: Add a system activity LED trigger")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
The "activity" trigger was inspired by the heartbeat one, but aims at
providing instant indication of the immediate CPU usage. Under idle
condition, it flashes 10ms every second. At 100% usage, it flashes
90ms every 100ms. The blinking frequency increases from 1 to 10 Hz
until either the load is high enough to saturate one CPU core or 50%
load is reached on a single-core system. Then past this point only the
duty cycle increases from 10 to 90%.
This results in a very visible activity reporting allowing one to
immediately tell whether a machine is under load or not, making it
quite suitable to be used in clusters.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
This patch converts the IDE specific LED trigger to a generic disk
activity LED trigger. The libata core is now a trigger source just
like before the IDE disk driver. It's merely a replacement of the
string ide by disk.
The patch is taken from http://dev.gentoo.org/~josejx/ata.patch and is
widely used by any ibook/powerbook owners with great satisfaction.
Likewise, it is very often used successfully on different ARM platforms.
Unlike the original patch, the existing 'ide-disk' trigger is still
available for backward compatibility. That reduce the amount of patches
in affected device trees out of the mainline kernel. For further
development, the new name 'disk-activity' should be used.
Cc: Joseph Jezak <josejx@gentoo.org>
Cc: Jörg Sommer <joerg@alea.gnuu.de>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit adds a new led_cdev flag LED_PANIC_INDICATOR, which
allows to mark a specific LED to be switched to the "panic"
trigger, on a kernel panic.
This is useful to allow the user to assign a regular trigger
to a given LED, and still blink that LED on a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a MTD trigger for flash (NAND/NOR) device
activity. The implementation is copied from IDE disk.
This trigger deprecates the "nand-disk" LED trigger, but for backwards
compatibility, we still keep the "nand-disk" trigger around.
The motivation for deprecating the "nand-disk" LED trigger is that
it only works for NAND drivers, whereas the "mtd" LED trigger
is more generic (in fact, "nand-disk" currently only works for
certain NAND drivers).
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
This commit introduces a new LED trigger which allows to configure
a LED to blink on a kernel panic (through panic_blink).
Notice that currently the Openmoko FreeRunner (GTA02) mach code
sets panic_blink to blink a hard-coded LED. The new trigger is
meant to introduce a generic mechanism to achieve this.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Some LED devices support flash/torch functionality through the LED subsystem.
This patch enables direct LED trigger controls by the driver.
Flash on/off and torch on/off can be done simply by other driver space.
Two trigger APIs are added, ledtrig_flash_ctrl() and ledtrig_torch_ctrl().
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
For better driver management, new subdirectory, 'trigger' is created.
All LED trigger drivers are moved into this directory.
Internal header, 'leds.h' is included in each LED trigger drivers.
Fix the location of header file, "leds.h" -> "../leds.h" in driver files.
One exception is here, 'ledtrig-timer.c'.
There is no need to include 'leds.h'. so '#include "leds.h"' line was removed.
Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Baolin Wang