pci_set_drvdata is called twice at the remove path of driver,
call it once.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
so if mdiobus_alloc fails, the errorpath doesnt do a netif_napi_del and also
doesn't set the priv data of the driver to NULL.
at the driver unload stage the driver doesn't remove the NAPI context, and
doesnt' set the priv data to NULL, and also doesn't call the pci_iounmap.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the calls after the pci_enable_device may fail, and will error out with out
disabling it. disable the device at error paths.
Signed-off-by: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define and use the bits of the PHY_CC (status change configuration) register.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define MTPR bit 0 of the register and use it where it is appropriate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define the MLSR (MAC Last Status Register bits) for:
- tx fifo under-run
- tx exceed collision
- tx late collision
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are currently updating the rx fifo error counter in the tx path while
it should have been the tx fifo error counter, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2048 is the usual value for busy-waiting on a register r/w, define it
as MAC_DEF_TIMEOUT and use it where it is appropriate.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reset of the MAC is currently done identically from two places
and one place is not waiting for the MAC_SM bit to be set after reset.
Everytime the MAC is software resetted a state machine is also needed
so consolidate the reset to its own function.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4e16d6ebd6 (r6040: define more MCR0
register bits) added #define values for MCR0 register bits and converted
uses of hardcoded magic values to uses of these defines.
However, one of the conversions looks suspicious:
#define MCR0 0x00 /* Control register 0 */
+#define MCR0_RCVEN 0x0002 /* Receive enable */
+#define MCR0_XMTEN 0x1000 /* Transmission enable */
/* Init RDC private data */
- lp->mcr0 = 0x1002;
+ lp->mcr0 = MCR0_XMTEN | MCR0;
I believe what was meant here was MCR0_XMTEN | MCR0_RCVEN, which makes
sense and matches the original values.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
checkpatch.pl complained about the line exceding 80 columns, and the
comment was actually on the same line as the code, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
instead of __attribute__((__aligned(size)__))
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 1 is the reset bit of the MAC status machine register, define and
use it.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC_RST bit is already defined, use it instead of 0x1 where applicable.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define more MCR0-register bits and use them in place of the bits values.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the conversion to phylib (3831861b: r6040: implement phylib) some
PHY-related variables and definitions are now useless, remove them.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should use an unique MDIO bus name which does not clash with anything
else in the system like the Fixed MDIO bus. The bus is now named:
r6040-<card number> which is unique in the system.
Reported-by: Vladimir Kolpakov <vova.kolpakov@gmail.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are checking whether the MCR0_HASHEN bit is set using a logical and
instead of bitwise and, fix that.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe reported to me that right after a bring up of a r6040 interface
the ethtool output had no consistent output with respect to link duplex
and speed. Fix this by adding a missing phy_start call in r6040_up and
conversely a phy_stop call in r6040_down to properly initialize phy states.
Reported-by: Joe Chou <Joe.Chou@rdc.com.tw>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the RDC driver into drivers/net/ethernet/rdc/ and make the
necessary Kconfig and Makefile changes.
CC: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Devendra Naga