As a prelude to implementing asynchronous fileserver operations in the afs
filesystem, rename struct afs_fs_cursor to afs_operation.
This struct is going to form the core of the operation management and is
going to acquire more members in later.
Signed-off-by: David Howells <dhowells@redhat.com>
Set a flag in the call struct to indicate an unmarshalling error rather
than return and handle an error from the decoding of file statuses. This
flag is checked on a successful return from the delivery function.
Signed-off-by: David Howells <dhowells@redhat.com>
afs_vol_interest objects represent the volume IDs currently being accessed
from a fileserver. These hold lists of afs_cb_interest objects that
repesent the superblocks using that volume ID on that server.
When a callback notification from the server telling of a modification by
another client arrives, the volume ID specified in the notification is
looked up in the server's afs_vol_interest list. Through the
afs_cb_interest list, the relevant superblocks can be iterated over and the
specific inode looked up and marked in each one.
Make the following efficiency improvements:
(1) Hold rcu_read_lock() over the entire processing rather than locking it
each time.
(2) Do all the callbacks for each vid together rather than individually.
Each volume then only needs to be looked up once.
(3) afs_vol_interest objects are now stored in an rb_tree rather than a
flat list to reduce the lookup step count.
(4) afs_vol_interest lookup is now done with RCU, but because it's in an
rb_tree which may rotate under us, a seqlock is used so that if it
changes during the walk, we repeat the walk with a lock held.
With this and the preceding patch which adds RCU-based lookups in the inode
cache, target volumes/vnodes can be taken without the need to take any
locks, except on the target itself.
Signed-off-by: David Howells <dhowells@redhat.com>
Show more information in /proc/net/afs/servers to make it easier to see
what's going on with the server probing.
Signed-off-by: David Howells <dhowells@redhat.com>
When an AFS client accesses a file, it receives a limited-duration callback
promise that the server will notify it if another client changes a file.
This callback duration can be a few hours in length.
If a client mounts a volume and then an application prevents it from being
unmounted, say by chdir'ing into it, but then does nothing for some time,
the rxrpc_peer record will expire and rxrpc-level keepalive will cease.
If there is NAT or a firewall between the client and the server, the route
back for the server may close after a comparatively short duration, meaning
that attempts by the server to notify the client may then bounce.
The client, however, may (so far as it knows) still have a valid unexpired
promise and will then rely on its cached data and will not see changes made
on the server by a third party until it incidentally rechecks the status or
the promise needs renewal.
To deal with this, the client needs to regularly probe the server. This
has two effects: firstly, it keeps a route open back for the server, and
secondly, it causes the server to disgorge any notifications that got
queued up because they couldn't be sent.
Fix this by adding a mechanism to emit regular probes.
Two levels of probing are made available: Under normal circumstances the
'slow' queue will be used for a fileserver - this just probes the preferred
address once every 5 mins or so; however, if server fails to respond to any
probes, the server will shift to the 'fast' queue from which all its
interfaces will be probed every 30s. When it finally responds, the record
will switch back to the slow queue.
Further notes:
(1) Probing is now no longer driven from the fileserver rotation
algorithm.
(2) Probes are dispatched to all interfaces on a fileserver when that an
afs_server object is set up to record it.
(3) The afs_server object is removed from the probe queues when we start
to probe it. afs_is_probing_server() returns true if it's not listed
- ie. it's undergoing probing.
(4) The afs_server object is added back on to the probe queue when the
final outstanding probe completes, but the probed_at time is set when
we're about to launch a probe so that it's not dependent on the probe
duration.
(5) The timer and the work item added for this must be handed a count on
net->servers_outstanding, which they hand on or release. This makes
sure that network namespace cleanup waits for them.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Reported-by: Dave Botsch <botsch@cnf.cornell.edu>
Signed-off-by: David Howells <dhowells@redhat.com>
Split the usage count on the afs_server struct to have an active count that
registers who's actually using it separately from the reference count on
the object.
This allows a future patch to dispatch polling probes without advancing the
"unuse" time into the future each time we emit a probe, which would
otherwise prevent unused server records from expiring.
Included in this:
(1) The latter part of afs_destroy_server() in which the RCU destruction
of afs_server objects is invoked and the outstanding server count is
decremented is split out into __afs_put_server().
(2) afs_put_server() now calls __afs_put_server() rather then setting the
management timer.
(3) The calls begun by afs_fs_give_up_all_callbacks() and
afs_fs_get_capabilities() can now take a ref on the server record, so
afs_destroy_server() can just drop its ref and needn't wait for the
completion of these calls. They'll put the ref when they're done.
(4) Because of (3), afs_fs_probe_done() no longer needs to wake up
afs_destroy_server() with server->probe_outstanding.
(5) afs_gc_servers can be simplified. It only needs to check if
server->active is 0 rather than playing games with the refcount.
(6) afs_manage_servers() can propose a server for gc if usage == 0 rather
than if ref == 1. The gc is effected by (5).
Signed-off-by: David Howells <dhowells@redhat.com>
The U-version VLDB volume record retrieved by the VL.GetEntryByNameU rpc op
carries a change counter (the serverUnique field) for each fileserver
listed in the record as backing that volume. This is incremented whenever
the registration details for a fileserver change (such as its address
list). Note that the same value will be seen in all UVLDB records that
refer to that fileserver.
This should be checked before calling the VL server to re-query the address
list for a fileserver. If it's the same, there's no point doing the query.
Reported-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
When a lookup is done in an AFS directory, the filesystem will speculate
and fetch up to 49 other statuses for files in the same directory and fetch
those as well, turning them into inodes or updating inodes that already
exist.
However, occasionally, a callback break might go missing due to NAT timing
out, but the afs filesystem doesn't then realise that the directory is not
up to date.
Alleviate this by using one of the status slots to check the directory in
which the lookup is being done.
Reported-by: Dave Botsch <botsch@cnf.cornell.edu>
Suggested-by: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Make the inode hash table RCU searchable so that searches that want to
access or modify an inode without taking a ref on that inode can do so
without taking the inode hash table lock.
The main thing this requires is some RCU annotation on the list
manipulation operations. Inodes are already freed by RCU in most cases.
Users of this interface must take care as the inode may be still under
construction or may be being torn down around them.
There are at least three instances where this can be of use:
(1) Testing whether the inode number iunique() is going to return is
currently unique (the iunique_lock is still held).
(2) Ext4 date stamp updating.
(3) AFS callback breaking.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
cc: linux-ext4@vger.kernel.org
cc: linux-afs@lists.infradead.org
Pull networking fixes from David Miller:
1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna
Bhowmik.
2) Nexthop attributes aren't being checked properly because of
mis-initialized iterator, from David Ahern.
3) Revert iop_idents_reserve() change as it caused performance
regressions and was just working around what is really a UBSAN bug
in the compiler. From Yuqi Jin.
4) Read MAC address properly from ROM in bmac driver (double iteration
proceeds past end of address array), from Jeremy Kerr.
5) Add Microsoft Surface device IDs to r8152, from Marc Payne.
6) Prevent reference to freed SKB in __netif_receive_skb_core(), from
Boris Sukholitko.
7) Fix ACK discard behavior in rxrpc, from David Howells.
8) Preserve flow hash across packet scrubbing in wireguard, from Jason
A. Donenfeld.
9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric
Dumazet.
10) Fix encryption error checking in kTLS code, from Vadim Fedorenko.
11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki.
12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet.
13) Fix use after free in mlxsw driver, from Jiri Pirko.
14) Order kTLS key destruction properly in mlx5 driver, from Tariq
Toukan.
15) Check devm_platform_ioremap_resource() return value properly in
several drivers, from Tiezhu Yang.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits)
net: smsc911x: Fix runtime PM imbalance on error
net/mlx4_core: fix a memory leak bug.
net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend
net: phy: mscc: fix initialization of the MACsec protocol mode
net: stmmac: don't attach interface until resume finishes
net: Fix return value about devm_platform_ioremap_resource()
net/mlx5: Fix error flow in case of function_setup failure
net/mlx5e: CT: Correctly get flow rule
net/mlx5e: Update netdev txq on completions during closure
net/mlx5: Annotate mutex destroy for root ns
net/mlx5: Don't maintain a case of del_sw_func being null
net/mlx5: Fix cleaning unmanaged flow tables
net/mlx5: Fix memory leak in mlx5_events_init
net/mlx5e: Fix inner tirs handling
net/mlx5e: kTLS, Destroy key object after destroying the TIS
net/mlx5e: Fix allowed tc redirect merged eswitch offload cases
net/mlx5: Avoid processing commands before cmdif is ready
net/mlx5: Fix a race when moving command interface to events mode
net/mlx5: Add command entry handling completion
rxrpc: Fix a memory leak in rxkad_verify_response()
...
Fix a warning due to an uninitialised variable.
le included from ../fs/afs/fs_probe.c:11:
../fs/afs/fs_probe.c: In function 'afs_fileserver_probe_result':
../fs/afs/internal.h:1453:2: warning: 'rtt_us' may be used uninitialized in this function [-Wmaybe-uninitialized]
1453 | printk("[%-6.6s] "FMT"\n", current->comm ,##__VA_ARGS__)
| ^~~~~~
../fs/afs/fs_probe.c:35:15: note: 'rtt_us' was declared here
Signed-off-by: David Howells <dhowells@redhat.com>
Don't call req->page_done() on each page as we finish filling it with
the data coming from the network. Whilst this might speed up the
application a bit, it's a problem if there's a network failure and the
operation has to be reissued.
If this happens, an oops occurs because afs_readpages_page_done() clears
the pointer to each page it unlocks and when a retry happens, the
pointers to the pages it wants to fill are now NULL (and the pages have
been unlocked anyway).
Instead, wait till the operation completes successfully and only then
release all the pages after clearing any terminal gap (the server can
give us less data than we requested as we're allowed to ask for more
than is available).
KASAN produces a bug like the following, and even without KASAN, it can
oops and panic.
BUG: KASAN: wild-memory-access in _copy_to_iter+0x323/0x5f4
Write of size 1404 at addr 0005088000000000 by task md5sum/5235
CPU: 0 PID: 5235 Comm: md5sum Not tainted 5.7.0-rc3-fscache+ #250
Hardware name: ASUS All Series/H97-PLUS, BIOS 2306 10/09/2014
Call Trace:
memcpy+0x39/0x58
_copy_to_iter+0x323/0x5f4
__skb_datagram_iter+0x89/0x2a6
skb_copy_datagram_iter+0x129/0x135
rxrpc_recvmsg_data.isra.0+0x615/0xd42
rxrpc_kernel_recv_data+0x1e9/0x3ae
afs_extract_data+0x139/0x33a
yfs_deliver_fs_fetch_data64+0x47a/0x91b
afs_deliver_to_call+0x304/0x709
afs_wait_for_call_to_complete+0x1cc/0x4ad
yfs_fs_fetch_data+0x279/0x288
afs_fetch_data+0x1e1/0x38d
afs_readpages+0x593/0x72e
read_pages+0xf5/0x21e
__do_page_cache_readahead+0x128/0x23f
ondemand_readahead+0x36e/0x37f
generic_file_buffered_read+0x234/0x680
new_sync_read+0x109/0x17e
vfs_read+0xe6/0x138
ksys_read+0xd8/0x14d
do_syscall_64+0x6e/0x8a
entry_SYSCALL_64_after_hwframe+0x49/0xb3
Fixes: 196ee9cd2d ("afs: Make afs_fs_fetch_data() take a list of pages")
Fixes: 30062bd13e ("afs: Implement YFS support in the fs client")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rxrpc currently uses a fixed 4s retransmission timeout until the RTT is
sufficiently sampled. This can cause problems with some fileservers with
calls to the cache manager in the afs filesystem being dropped from the
fileserver because a packet goes missing and the retransmission timeout is
greater than the call expiry timeout.
Fix this by:
(1) Copying the RTT/RTO calculation code from Linux's TCP implementation
and altering it to fit rxrpc.
(2) Altering the various users of the RTT to make use of the new SRTT
value.
(3) Replacing the use of rxrpc_resend_timeout to use the calculated RTO
value instead (which is needed in jiffies), along with a backoff.
Notes:
(1) rxrpc provides RTT samples by matching the serial numbers on outgoing
DATA packets that have the RXRPC_REQUEST_ACK set and PING ACK packets
against the reference serial number in incoming REQUESTED ACK and
PING-RESPONSE ACK packets.
(2) Each packet that is transmitted on an rxrpc connection gets a new
per-connection serial number, even for retransmissions, so an ACK can
be cross-referenced to a specific trigger packet. This allows RTT
information to be drawn from retransmitted DATA packets also.
(3) rxrpc maintains the RTT/RTO state on the rxrpc_peer record rather than
on an rxrpc_call because many RPC calls won't live long enough to
generate more than one sample.
(4) The calculated SRTT value is in units of 8ths of a microsecond rather
than nanoseconds.
The (S)RTT and RTO values are displayed in /proc/net/rxrpc/peers.
Fixes: 17926a7932 ([AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both"")
Signed-off-by: David Howells <dhowells@redhat.com>
When an operation is meant to be done uninterruptibly (such as
FS.StoreData), we should not be allowing volume and server record checking
to be interrupted.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: David Howells <dhowells@redhat.com>
AFS keeps track of the epoch value from the rxrpc protocol to note (a) when
a fileserver appears to have restarted and (b) when different endpoints of
a fileserver do not appear to be associated with the same fileserver
(ie. all probes back from a fileserver from all of its interfaces should
carry the same epoch).
However, the AFS_SERVER_FL_HAVE_EPOCH flag that indicates that we've
received the server's epoch is never set, though it is used.
Fix this to set the flag when we first receive an epoch value from a probe
sent to the filesystem client from the fileserver.
Fixes: 3bf0fb6f33 ("afs: Probe multiple fileservers simultaneously")
Signed-off-by: David Howells <dhowells@redhat.com>
Remove three bits:
(1) afs_server::no_epoch is neither set nor used.
(2) afs_server::have_result is set and a wakeup is applied to it, but
nothing looks at it or waits on it.
(3) afs_vl_dump_edestaddrreq() prints afs_addr_list::probed, but nothing
sets it for VL servers.
Signed-off-by: David Howells <dhowells@redhat.com>
If a dentry's version is somewhere between invalid_before and the current
directory version, we should be setting it forward to the current version,
not backwards to the invalid_before version. Note that we're only doing
this at all because dentry::d_fsdata isn't large enough on a 32-bit system.
Fix this by using a separate variable for invalid_before so that we don't
accidentally clobber the current dir version.
Fixes: a4ff7401fb ("afs: Keep track of invalid-before version for dentry coherency")
Signed-off-by: David Howells <dhowells@redhat.com>
AFS directories are retained locally as a structured file, with lookup
being effected by a local search of the file contents. When a modification
(such as mkdir) happens, the dir file content is modified locally rather
than redownloading the directory.
The directory contents are accessed in a number of ways, with a number of
different locks schemes:
(1) Download of contents - dvnode->validate_lock/write in afs_read_dir().
(2) Lookup and readdir - dvnode->validate_lock/read in afs_dir_iterate(),
downgrading from (1) if necessary.
(3) d_revalidate of child dentry - dvnode->validate_lock/read in
afs_do_lookup_one() downgrading from (1) if necessary.
(4) Edit of dir after modification - page locks on individual dir pages.
Unfortunately, because (4) uses different locking scheme to (1) - (3),
nothing protects against the page being scanned whilst the edit is
underway. Even download is not safe as it doesn't lock the pages - relying
instead on the validate_lock to serialise as a whole (the theory being that
directory contents are treated as a block and always downloaded as a
block).
Fix this by write-locking dvnode->validate_lock around the edits. Care
must be taken in the rename case as there may be two different dirs - but
they need not be locked at the same time. In any case, once the lock is
taken, the directory version must be rechecked, and the edit skipped if a
later version has been downloaded by revalidation (there can't have been
any local changes because the VFS holds the inode lock, but there can have
been remote changes).
Fixes: 63a4681ff3 ("afs: Locally edit directory data for mkdir/create/unlink/...")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the length of the dump of a bad YFSFetchStatus record. The function
was copied from the AFS version, but the YFS variant contains bigger fields
and extra information, so expand the dump to match.
Signed-off-by: David Howells <dhowells@redhat.com>
The afs_deliver_fs_rename() and yfs_deliver_fs_rename() functions both only
decode the second file status returned unless the parent directories are
different - unfortunately, this means that the xdr pointer isn't advanced
and the volsync record will be read incorrectly in such an instance.
Fix this by always decoding the second status into the second
status/callback block which wasn't being used if the dirs were the same.
The afs_update_dentry_version() calls that update the directory data
version numbers on the dentries can then unconditionally use the second
status record as this will always reflect the state of the destination dir
(the two records will be identical if the destination dir is the same as
the source dir)
Fixes: 260a980317 ("[AFS]: Add "directory write" support.")
Fixes: 30062bd13e ("afs: Implement YFS support in the fs client")
Signed-off-by: David Howells <dhowells@redhat.com>
If we're decoding an AFSFetchStatus record and we see that the version is 1
and the abort code is set and we're expecting inline errors, then we store
the abort code and ignore the remaining status record (which is correct),
but we don't set the flag to say we got a valid abort code.
This can affect operation of YFS.RemoveFile2 when removing a file and the
operation of {,Y}FS.InlineBulkStatus when prospectively constructing or
updating of a set of inodes during a lookup.
Fix this to indicate the reception of a valid abort code.
Fixes: a38a75581e ("afs: Fix unlink to handle YFS.RemoveFile2 better")
Signed-off-by: David Howells <dhowells@redhat.com>
If we receive a status record that has VNOVNODE set in the abort field,
xdr_decode_AFSFetchStatus() and xdr_decode_YFSFetchStatus() don't advance
the XDR pointer, thereby corrupting anything subsequent decodes from the
same block of data.
This has the potential to affect AFS.InlineBulkStatus and
YFS.InlineBulkStatus operation, but probably doesn't since the status
records are extracted as individual blocks of data and the buffer pointer
is reset between blocks.
It does affect YFS.RemoveFile2 operation, corrupting the volsync record -
though that is not currently used.
Other operations abort the entire operation rather than returning an error
inline, in which case there is no decoding to be done.
Fix this by unconditionally advancing the xdr pointer.
Fixes: 684b0f68cf ("afs: Fix AFSFetchStatus decoder to provide OpenAFS compatibility")
Signed-off-by: David Howells <dhowells@redhat.com>
When it's probing all of a fileserver's interfaces to find which one is
best to use, afs_do_probe_fileserver() takes a lock on the server record
and notes the pointer to the address list.
It doesn't, however, pin the address list, so as soon as it drops the
lock, there's nothing to stop the address list from being freed under
us.
Fix this by taking a ref on the address list inside the locked section
and dropping it at the end of the function.
Fixes: 3bf0fb6f33 ("afs: Probe multiple fileservers simultaneously")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull networking fixes from David Miller:
1) Fix deadlock in bpf_send_signal() from Yonghong Song.
2) Fix off by one in kTLS offload of mlx5, from Tariq Toukan.
3) Add missing locking in iwlwifi mvm code, from Avraham Stern.
4) Fix MSG_WAITALL handling in rxrpc, from David Howells.
5) Need to hold RTNL mutex in tcindex_partial_destroy_work(), from Cong
Wang.
6) Fix producer race condition in AF_PACKET, from Willem de Bruijn.
7) cls_route removes the wrong filter during change operations, from
Cong Wang.
8) Reject unrecognized request flags in ethtool netlink code, from
Michal Kubecek.
9) Need to keep MAC in reset until PHY is up in bcmgenet driver, from
Doug Berger.
10) Don't leak ct zone template in act_ct during replace, from Paul
Blakey.
11) Fix flushing of offloaded netfilter flowtable flows, also from Paul
Blakey.
12) Fix throughput drop during tx backpressure in cxgb4, from Rahul
Lakkireddy.
13) Don't let a non-NULL skb->dev leave the TCP stack, from Eric
Dumazet.
14) TCP_QUEUE_SEQ socket option has to update tp->copied_seq as well,
also from Eric Dumazet.
15) Restrict macsec to ethernet devices, from Willem de Bruijn.
16) Fix reference leak in some ethtool *_SET handlers, from Michal
Kubecek.
17) Fix accidental disabling of MSI for some r8169 chips, from Heiner
Kallweit.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (138 commits)
net: Fix CONFIG_NET_CLS_ACT=n and CONFIG_NFT_FWD_NETDEV={y, m} build
net: ena: Add PCI shutdown handler to allow safe kexec
selftests/net/forwarding: define libs as TEST_PROGS_EXTENDED
selftests/net: add missing tests to Makefile
r8169: re-enable MSI on RTL8168c
net: phy: mdio-bcm-unimac: Fix clock handling
cxgb4/ptp: pass the sign of offset delta in FW CMD
net: dsa: tag_8021q: replace dsa_8021q_remove_header with __skb_vlan_pop
net: cbs: Fix software cbs to consider packet sending time
net/mlx5e: Do not recover from a non-fatal syndrome
net/mlx5e: Fix ICOSQ recovery flow with Striding RQ
net/mlx5e: Fix missing reset of SW metadata in Striding RQ reset
net/mlx5e: Enhance ICOSQ WQE info fields
net/mlx5_core: Set IB capability mask1 to fix ib_srpt connection failure
selftests: netfilter: add nfqueue test case
netfilter: nft_fwd_netdev: allow to redirect to ifb via ingress
netfilter: nft_fwd_netdev: validate family and chain type
netfilter: nft_set_rbtree: Detect partial overlaps on insertion
netfilter: nft_set_rbtree: Introduce and use nft_rbtree_interval_start()
netfilter: nft_set_pipapo: Separate partial and complete overlap cases on insertion
...
Fix the handling of signals in client rxrpc calls made by the afs
filesystem. Ignore signals completely, leaving call abandonment or
connection loss to be detected by timeouts inside AF_RXRPC.
Allowing a filesystem call to be interrupted after the entire request has
been transmitted and an abort sent means that the server may or may not
have done the action - and we don't know. It may even be worse than that
for older servers.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
When an AFS service handler function aborts a call, AF_RXRPC marks the call
as complete - which means that it's not going to get any more packets from
the receiver. This is a problem because reception of the final ACK is what
triggers afs_deliver_to_call() to drop the final ref on the afs_call
object.
Instead, aborted AFS service calls may then just sit around waiting for
ever or until they're displaced by a new call on the same connection
channel or a connection-level abort.
Fix this by calling afs_set_call_complete() to finalise the afs_call struct
representing the call.
However, we then need to drop the ref that stops the call from being
deallocated. We can do this in afs_set_call_complete(), as the work queue
is holding a separate ref of its own, but then we shouldn't do it in
afs_process_async_call() and afs_delete_async_call().
call->drop_ref is set to indicate that a ref needs dropping for a call and
this is dealt with when we transition a call to AFS_CALL_COMPLETE.
But then we also need to get rid of the ref that pins an asynchronous
client call. We can do this by the same mechanism, setting call->drop_ref
for an async client call too.
We can also get rid of call->incoming since nothing ever sets it and only
one thing ever checks it (futilely).
A trace of the rxrpc_call and afs_call struct ref counting looks like:
<idle>-0 [001] ..s5 164.764892: rxrpc_call: c=00000002 SEE u=3 sp=rxrpc_new_incoming_call+0x473/0xb34 a=00000000442095b5
<idle>-0 [001] .Ns5 164.766001: rxrpc_call: c=00000002 QUE u=4 sp=rxrpc_propose_ACK+0xbe/0x551 a=00000000442095b5
<idle>-0 [001] .Ns4 164.766005: rxrpc_call: c=00000002 PUT u=3 sp=rxrpc_new_incoming_call+0xa3f/0xb34 a=00000000442095b5
<idle>-0 [001] .Ns7 164.766433: afs_call: c=00000002 WAKE u=2 o=11 sp=rxrpc_notify_socket+0x196/0x33c
kworker/1:2-1810 [001] ...1 164.768409: rxrpc_call: c=00000002 SEE u=3 sp=rxrpc_process_call+0x25/0x7ae a=00000000442095b5
kworker/1:2-1810 [001] ...1 164.769439: rxrpc_tx_packet: c=00000002 e9f1a7a8:95786a88:00000008:09c5 00000001 00000000 02 22 ACK CallAck
kworker/1:2-1810 [001] ...1 164.769459: rxrpc_call: c=00000002 PUT u=2 sp=rxrpc_process_call+0x74f/0x7ae a=00000000442095b5
kworker/1:2-1810 [001] ...1 164.770794: afs_call: c=00000002 QUEUE u=3 o=12 sp=afs_deliver_to_call+0x449/0x72c
kworker/1:2-1810 [001] ...1 164.770829: afs_call: c=00000002 PUT u=2 o=12 sp=afs_process_async_call+0xdb/0x11e
kworker/1:2-1810 [001] ...2 164.771084: rxrpc_abort: c=00000002 95786a88:00000008 s=0 a=1 e=1 K-1
kworker/1:2-1810 [001] ...1 164.771461: rxrpc_tx_packet: c=00000002 e9f1a7a8:95786a88:00000008:09c5 00000002 00000000 04 00 ABORT CallAbort
kworker/1:2-1810 [001] ...1 164.771466: afs_call: c=00000002 PUT u=1 o=12 sp=SRXAFSCB_ProbeUuid+0xc1/0x106
The abort generated in SRXAFSCB_ProbeUuid(), labelled "K-1", indicates that
the local filesystem/cache manager didn't recognise the UUID as its own.
Fixes: 2067b2b3f4 ("afs: Fix the CB.ProbeUuid service handler to reply correctly")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix a couple of tracelines to indicate the usage count after the atomic op,
not the usage count before it to be consistent with other afs and rxrpc
trace lines.
Change the wording of the afs_call_trace_work trace ID label from "WORK" to
"QUEUE" to reflect the fact that it's queueing work, not doing work.
Fixes: 341f741f04 ("afs: Refcount the afs_call struct")
Signed-off-by: David Howells <dhowells@redhat.com>
Fix the interruptibility of kernel-initiated client calls so that they're
either only interruptible when they're waiting for a call slot to come
available or they're not interruptible at all. Either way, they're not
interruptible during transmission.
This should help prevent StoreData calls from being interrupted when
writeback is in progress. It doesn't, however, handle interruption during
the receive phase.
Userspace-initiated calls are still interruptable. After the signal has
been handled, sendmsg() will return the amount of data copied out of the
buffer and userspace can perform another sendmsg() call to continue
transmission.
Fixes: bc5e3a546d ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
afs_put_addrlist() casts kfree() to rcu_callback_t. Apart from being wrong
in theory, this might also blow up when people start enforcing function
types via compiler instrumentation, and it means the rcu_head has to be
first in struct afs_addr_list.
Use kfree_rcu() instead, it's simpler and more correct.
Signed-off-by: Jann Horn <jannh@google.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs file system parameter updates from Al Viro:
"Saner fs_parser.c guts and data structures. The system-wide registry
of syntax types (string/enum/int32/oct32/.../etc.) is gone and so is
the horror switch() in fs_parse() that would have to grow another case
every time something got added to that system-wide registry.
New syntax types can be added by filesystems easily now, and their
namespace is that of functions - not of system-wide enum members. IOW,
they can be shared or kept private and if some turn out to be widely
useful, we can make them common library helpers, etc., without having
to do anything whatsoever to fs_parse() itself.
And we already get that kind of requests - the thing that finally
pushed me into doing that was "oh, and let's add one for timeouts -
things like 15s or 2h". If some filesystem really wants that, let them
do it. Without somebody having to play gatekeeper for the variants
blessed by direct support in fs_parse(), TYVM.
Quite a bit of boilerplate is gone. And IMO the data structures make a
lot more sense now. -200LoC, while we are at it"
* 'merge.nfs-fs_parse.1' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (25 commits)
tmpfs: switch to use of invalfc()
cgroup1: switch to use of errorfc() et.al.
procfs: switch to use of invalfc()
hugetlbfs: switch to use of invalfc()
cramfs: switch to use of errofc() et.al.
gfs2: switch to use of errorfc() et.al.
fuse: switch to use errorfc() et.al.
ceph: use errorfc() and friends instead of spelling the prefix out
prefix-handling analogues of errorf() and friends
turn fs_param_is_... into functions
fs_parse: handle optional arguments sanely
fs_parse: fold fs_parameter_desc/fs_parameter_spec
fs_parser: remove fs_parameter_description name field
add prefix to fs_context->log
ceph_parse_param(), ceph_parse_mon_ips(): switch to passing fc_log
new primitive: __fs_parse()
switch rbd and libceph to p_log-based primitives
struct p_log, variants of warnf() et.al. taking that one instead
teach logfc() to handle prefices, give it saner calling conventions
get rid of cg_invalf()
...
Unused now.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Don't do a single array; attach them to fsparam_enum() entry
instead. And don't bother trying to embed the names into those -
it actually loses memory, with no real speedup worth mentioning.
Simplifies validation as well.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The afs filesystem needs to prohibit certain characters from cell names,
such as '/', as these are used to form filenames in procfs, leading to
the following warning being generated:
WARNING: CPU: 0 PID: 3489 at fs/proc/generic.c:178
Fix afs_alloc_cell() to disallow nonprintable characters, '/', '@' and
names that begin with a dot.
Remove the check for "@cell" as that is then redundant.
This can be tested by running:
echo add foo/.bar 1.2.3.4 >/proc/fs/afs/cells
Note that we will also need to deal with:
- Names ending in ".invalid" shouldn't be passed to the DNS.
- Names that contain non-valid domainname chars shouldn't be passed to
the DNS.
- DNS replies that say "your-dns-needs-immediate-attention.<gTLD>" and
replies containing A records that say 127.0.53.53 should be
considered invalid.
[https://www.icann.org/en/system/files/files/name-collision-mitigation-01aug14-en.pdf]
but these need to be dealt with by the kafs-client DNS program rather
than the kernel.
Reported-by: syzbot+b904ba7c947a37b4b291@syzkaller.appspotmail.com
Cc: stable@kernel.org
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Merge misc fixes from David Howells.
Two afs fixes and a key refcounting fix.
* dhowells:
afs: Fix afs_lookup() to not clobber the version on a new dentry
afs: Fix use-after-loss-of-ref
keys: Fix request_key() cache
Fix afs_lookup() to not clobber the version set on a new dentry by
afs_do_lookup() - especially as it's using the wrong version of the
version (we need to use the one given to us by whatever op the dir
contents correspond to rather than what's in the afs_vnode).
Fixes: 9dd0b82ef5 ("afs: Fix missing dentry data version updating")
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
afs_lookup() has a tracepoint to indicate the outcome of
d_splice_alias(), passing it the inode to retrieve the fid from.
However, the function gave up its ref on that inode when it called
d_splice_alias(), which may have failed and dropped the inode.
Fix this by caching the fid.
Fixes: 80548b0399 ("afs: Add more tracepoints")
Reported-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Show the name of each volume in /proc/net/afs/<cell>/volumes to make it
easier to work out the name corresponding to a volume ID. This makes it
easier to work out which mounts in /proc/mounts correspond to which volume
ID.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Fix missing cell comparison in afs_test_super(). Without this, any pair
volumes that have the same volume ID will share a superblock, no matter the
cell, unless they're in different network namespaces.
Normally, most users will only deal with a single cell and so they won't
see this. Even if they do look into a second cell, they won't see a
problem unless they happen to hit a volume with the same ID as one they've
already got mounted.
Before the patch:
# ls /afs/grand.central.org/archive
linuxdev/ mailman/ moin/ mysql/ pipermail/ stage/ twiki/
# ls /afs/kth.se/
linuxdev/ mailman/ moin/ mysql/ pipermail/ stage/ twiki/
# cat /proc/mounts | grep afs
none /afs afs rw,relatime,dyn,autocell 0 0
#grand.central.org:root.cell /afs/grand.central.org afs ro,relatime 0 0
#grand.central.org:root.archive /afs/grand.central.org/archive afs ro,relatime 0 0
#grand.central.org:root.archive /afs/kth.se afs ro,relatime 0 0
After the patch:
# ls /afs/grand.central.org/archive
linuxdev/ mailman/ moin/ mysql/ pipermail/ stage/ twiki/
# ls /afs/kth.se/
admin/ common/ install/ OldFiles/ service/ system/
bakrestores/ home/ misc/ pkg/ src/ wsadmin/
# cat /proc/mounts | grep afs
none /afs afs rw,relatime,dyn,autocell 0 0
#grand.central.org:root.cell /afs/grand.central.org afs ro,relatime 0 0
#grand.central.org:root.archive /afs/grand.central.org/archive afs ro,relatime 0 0
#kth.se:root.cell /afs/kth.se afs ro,relatime 0 0
Fixes: ^1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Carsten Jacobi <jacobi@de.ibm.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
cc: Todd DeSantis <atd@us.ibm.com>
Fix the lookup method on the dynamic root directory such that creation
calls, such as mkdir, open(O_CREAT), symlink, etc. fail with EOPNOTSUPP
rather than failing with some odd error (such as EEXIST).
lookup() itself tries to create automount directories when it is invoked.
These are cached locally in RAM and not committed to storage.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Each AFS mountpoint has strings that define the target to be mounted. This
is required to end in a dot that is supposed to be stripped off. The
string can include suffixes of ".readonly" or ".backup" - which are
supposed to come before the terminal dot. To add to the confusion, the "fs
lsmount" afs utility does not show the terminal dot when displaying the
string.
The kernel mount source string parser, however, assumes that the terminal
dot marks the suffix and that the suffix is always "" and is thus ignored.
In most cases, there is no suffix and this is not a problem - but if there
is a suffix, it is lost and this affects the ability to mount the correct
volume.
The command line mount command, on the other hand, is expected not to
include a terminal dot - so the problem doesn't arise there.
Fix this by making sure that the dot exists and then stripping it when
passing the string to the mount configuration.
Fixes: bec5eb6141 ("AFS: Implement an autocell mount capability [ver #2]")
Reported-by: Jonathan Billings <jsbillings@jsbillings.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Tested-by: Jonathan Billings <jsbillings@jsbillings.org>
Make the AFS dynamic root superblock R/W so that SELinux can set the
security label on it. Without this, upgrades to, say, the Fedora
filesystem-afs RPM fail if afs is mounted on it because the SELinux label
can't be (re-)applied.
It might be better to make it possible to bypass the R/O check for LSM
label application through setxattr.
Fixes: 4d673da145 ("afs: Support the AFS dynamic root")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
cc: selinux@vger.kernel.org
cc: linux-security-module@vger.kernel.org
afs_find_server tries to find a server that has an address that
matches the transport address of an rxrpc peer. The code assumes
that the transport address is always ipv6, with ipv4 represented
as ipv4 mapped addresses, but that's not the case. If the transport
family is AF_INET, srx->transport.sin6.sin6_addr.s6_addr32[] will
be beyond the actual ipv4 address and will always be 0, and all
ipv4 addresses will be seen as matching.
As a result, the first ipv4 address seen on any server will be
considered a match, and the server returned may be the wrong one.
One of the consequences is that callbacks received over ipv4 will
only be correctly applied for the server that happens to have the
first ipv4 address on the fs_addresses4 list. Callbacks over ipv4
from all other servers are dropped, causing the client to serve stale
data.
This is fixed by looking at the transport family, and comparing ipv4
addresses based on a sockaddr_in structure rather than a sockaddr_in6.
Fixes: d2ddc776a4 ("afs: Overhaul volume and server record caching and fileserver rotation")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
-----BEGIN PGP SIGNATURE-----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=YjAm
-----END PGP SIGNATURE-----
Merge tag 'afs-next-20191121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull AFS updates from David Howells:
"Minor cleanups and fix:
- Minor fix to make some debugging statements display information
from the correct iov_iter.
- Rename some members and variables to make things more obvious or
consistent.
- Provide a helper to wrap increments of the usage count on the
afs_read struct.
- Use scnprintf() to print into a stack buffer rather than sprintf().
- Remove some set but unused variables"
* tag 'afs-next-20191121' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Remove set but not used variable 'ret'
afs: Remove set but not used variables 'before', 'after'
afs: xattr: use scnprintf
afs: Introduce an afs_get_read() refcount helper
afs: Rename desc -> req in afs_fetch_data()
afs: Switch the naming of call->iter and call->_iter
afs: Use call->_iter not &call->iter in debugging statements
Pull RCU updates from Ingo Molnar:
"The main changes in this cycle were:
- Dynamic tick (nohz) updates, perhaps most notably changes to force
the tick on when needed due to lengthy in-kernel execution on CPUs
on which RCU is waiting.
- Linux-kernel memory consistency model updates.
- Replace rcu_swap_protected() with rcu_prepace_pointer().
- Torture-test updates.
- Documentation updates.
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
security/safesetid: Replace rcu_swap_protected() with rcu_replace_pointer()
net/sched: Replace rcu_swap_protected() with rcu_replace_pointer()
net/netfilter: Replace rcu_swap_protected() with rcu_replace_pointer()
net/core: Replace rcu_swap_protected() with rcu_replace_pointer()
bpf/cgroup: Replace rcu_swap_protected() with rcu_replace_pointer()
fs/afs: Replace rcu_swap_protected() with rcu_replace_pointer()
drivers/scsi: Replace rcu_swap_protected() with rcu_replace_pointer()
drm/i915: Replace rcu_swap_protected() with rcu_replace_pointer()
x86/kvm/pmu: Replace rcu_swap_protected() with rcu_replace_pointer()
rcu: Upgrade rcu_swap_protected() to rcu_replace_pointer()
rcu: Suppress levelspread uninitialized messages
rcu: Fix uninitialized variable in nocb_gp_wait()
rcu: Update descriptions for rcu_future_grace_period tracepoint
rcu: Update descriptions for rcu_nocb_wake tracepoint
rcu: Remove obsolete descriptions for rcu_barrier tracepoint
rcu: Ensure that ->rcu_urgent_qs is set before resched IPI
workqueue: Convert for_each_wq to use built-in list check
rcu: Several rcu_segcblist functions can be static
rcu: Remove unused function hlist_bl_del_init_rcu()
Documentation: Rename rcu_node_context_switch() to rcu_note_context_switch()
...
-----BEGIN PGP SIGNATURE-----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=QCEy
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk
Pull printk updates from Petr Mladek:
- Allow to print symbolic error names via new %pe modifier.
- Use pr_warn() instead of the remaining pr_warning() calls. Fix
formatting of the related lines.
- Add VSPRINTF entry to MAINTAINERS.
* tag 'printk-for-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/pmladek/printk: (32 commits)
checkpatch: don't warn about new vsprintf pointer extension '%pe'
MAINTAINERS: Add VSPRINTF
tools lib api: Renaming pr_warning to pr_warn
ASoC: samsung: Use pr_warn instead of pr_warning
lib: cpu_rmap: Use pr_warn instead of pr_warning
trace: Use pr_warn instead of pr_warning
dma-debug: Use pr_warn instead of pr_warning
vgacon: Use pr_warn instead of pr_warning
fs: afs: Use pr_warn instead of pr_warning
sh/intc: Use pr_warn instead of pr_warning
scsi: Use pr_warn instead of pr_warning
platform/x86: intel_oaktrail: Use pr_warn instead of pr_warning
platform/x86: asus-laptop: Use pr_warn instead of pr_warning
platform/x86: eeepc-laptop: Use pr_warn instead of pr_warning
oprofile: Use pr_warn instead of pr_warning
of: Use pr_warn instead of pr_warning
macintosh: Use pr_warn instead of pr_warning
idsn: Use pr_warn instead of pr_warning
ide: Use pr_warn instead of pr_warning
crypto: n2: Use pr_warn instead of pr_warning
...
By default s_maxbytes is set to MAX_NON_LFS, which limits the usable
file size to 2GB, enforced by the vfs.
Commit b9b1f8d593 ("AFS: write support fixes") added support for the
64-bit fetch and store server operations, but did not change this value.
As a result, attempts to write past the 2G mark result in EFBIG errors:
$ dd if=/dev/zero of=foo bs=1M count=1 seek=2048
dd: error writing 'foo': File too large
Set s_maxbytes to MAX_LFS_FILESIZE.
Fixes: b9b1f8d593 ("AFS: write support fixes")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Servers sending callback breaks to the YFS_CM_SERVICE service may
send up to YFSCBMAX (1024) fids in a single RPC. Anything over
AFSCBMAX (50) will cause the assert in afs_break_callbacks to trigger.
Remove the assert, as the count has already been checked against
the appropriate max values in afs_deliver_cb_callback and
afs_deliver_yfs_cb_callback.
Fixes: 35dbfba311 ("afs: Implement the YFS cache manager service")
Signed-off-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Howells