By default, watermark is set to '1'. Watermark is used to fine tune
cyclic dma buffer period. In case watermark is left untouched (e.g. 1)
and several channels are being scanned, buffer period is wrongly set
(e.g. to 1 sample). As a consequence, data is never pushed to upper layer.
Fix buffer period size, by taking scan channels number into account.
Fixes: 2763ea0585 ("iio: adc: stm32: add optional dma support")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the patch to the file ti_am335x_adc.c
which fixes the following coccinelle warning:
WARNING: Comparison to bool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the registers are read out once per conversion interval. If
the reading is delayed as the conversion has not yet finished, this extra
time is treated as being part of the readout, although it should delay
the start of the poll interval. This results in the interval starting
slightly earlier in each iteration, until all time between reads is
spent polling the status registers instead of sleeping.
To fix this, the delay has to account for the state of the conversion
ready flag. Whenever the conversion is already finished, schedule the next
read on the regular interval, otherwise schedule it one interval after the
flag bit has been set.
Split the work function in two functions, one for the status poll and one
for reading the values, to be able to note down the time when the flag
bit is raised.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As the timestamp is no longer (ab-)used to measure the function run time,
it can be taken at the correct time, i.e. when the conversion has finished.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The iio timestamp clock is user selectable and may be non-monotonic. Also,
only part of the acquisition time is measured, thus the delay was longer
than intended.
Use a monotonic timestamp to track the time for the next poll iteration.
The timestamp is advanced by the sampling interval each iteration. In case
the conversion overrruns the register readout (i.e. fast sampling combined
with a slow bus), one or multiple samples will be dropped.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calibration register is used for calculating current register in
hardware according to datasheet:
current = shunt_volt * calib_register / 2048 (ina 226)
current = shunt_volt * calib_register / 4096 (ina 219)
Fix calib_register value to 2048 for ina226 and 4096 for ina 219 in
order to avoid truncation error and provide best precision allowed
by shunt_voltage measurement. Make current scale value follow changes
of shunt_resistor from sysfs as calib_register value is now fixed.
Power_lsb value should also follow shunt_resistor changes as stated in
datasheet:
power_lsb = 25 * current_lsb (ina 226)
power_lsb = 20 * current_lsb (ina 219)
This is a part of the patchset: https://lkml.org/lkml/2017/11/22/394
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a patch to the at91_adc.c file that fixes up a brace
warning found by the checkpatch.pl tool
Signed-off-by: Venkat Prashanth B U <venkat.prashanth2498@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Return value in hx711_reset() should indicate status of dout otherwise the
calling function is reporting an error as false positive
If there are two reads too close to each other, then the second one will
never succeed. This happens especially when using buffered mode with both
channels enabled.
When changing the channel on every trigger event the former 100 ms are not
enough for waiting until the device indicates normal mode.
Wait up to 1 second until the device turns into normal mode.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add buffer to device data struct and add trigger function
Data format is quite simple:
voltage - channel 0 32 Bit
voltage - channel 1 32 Bit
timestamp 64 Bit
Using both channels at the same time is working quite slow because of
changing the channel which needs a dummy read.
Signed-off-by: Andreas Klinger <ak@it-klinger.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The conversion time can be up to 16 seconds (8 ms per channel, 2 channels,
1024 times averaging).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Although the datasheet states the CNVR flag is cleared by reading the
BUS_VOLTAGE register, it is actually cleared by reading any of the
voltage/current/power registers.
The behaviour has been confirmed by TI support:
http://e2e.ti.com/support/amplifiers/current-shunt-monitors/f/931/p/647053/2378282
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The timestamp is inserted into the buffer after the sample data by
iio_push_to_buffers_with_timestamp, document the space requirement for
the timestamp.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
iio_push_to_buffers_with_timestamp expects a void pointer, so the cast
is both unnecessary and misleading.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On some Meson8 devices the channel muxes are not programmed. This
results in garbage values when trying to read channels that are not set
up.
Fix this by initializing the channel 0 and 1 muxes in
MESON_SAR_ADC_CHAN_10_SW as well as the muxes for all other channels in
MESON_SAR_ADC_AUX_SW based on what the vendor driver does (which is
simply a 1:1 mapping of channel number and channel mux).
This only showed up on Meson8 devices, because for GXBB and newer BL30
is taking care of initializing the channel muxes.
This additionally fixes a typo in the
MESON_SAR_ADC_AUX_SW_MUX_SEL_CHAN_MASK macro because the old definition
assumed that the register fields were 2 bit wide, while they are
actually 3 bit wide.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GX SoCs use a 1.2 MHz ADC clock, while the older SoCs use a 1.14 MHz
clock.
A comment in the driver from Amlogic's GPL kernel says that it's
running at 1.28 MHz. However, it's actually programming a divider of
20 + 1. With a XTAL clock of 24 MHz this results in a frequency of
1.14 MHz. (their calculation might be based on a 27 MHz XTAL clock,
but this is not what we have on the Meson8 and Meson8b SoCs).
The ADC was still working with the 1.2MHz clock. In my own tests I did
not see a difference between 1.2 and 1.14 MHz (regardless of the clock
frequency used, the ADC results were identical).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge issue pointed out by Stephen in
drivers/iio/adc/meson_saradc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The GPIO core provides a handy GPIO_LOOKUP() macro to populate a struct
gpiod_lookup array without having to spell out attribute names (but
still avoid breakage when attributes within the struct are rearranged
or added).
The axp288_adc.c driver uses a similar macro to populate a struct
iio_map array. Make it available to others.
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The "sana" clock is not used at SAR ADC module in Amlogic Meson SoC,
it is irrelevant for the SAR ADC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ASPEED SoC must deassert a reset in order to use the ADC peripheral.
The device tree bindings are updated to document the resets phandle, and
the example is updated to match what is expected for both the reset and
clock phandle. Note that the bindings should have always had the reset
controller, as the hardware is unusable without it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32H7 ADC channels can be configured either as single ended or
differential with 'st,adc-channels' or 'st,adc-diff-channels'
(positive and negative input pair: <vinp vinn>, ...).
Differential channels have different offset and scale, from spec:
raw value = (full_scale / 2) * (1 + (vinp - vinn) / vref).
Add offset attribute.
Differential channels are selected by DIFSEL register. Negative
inputs must be added to pre-selected channels as well (PCSEL).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove const array that defines channels. Build channels definition
at probe time, when initializing channels (only for requested ones).
This will ease adding differential channels support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reducing shunt and bus voltage range improves the accuracy, so allow
altering the default settings.
Both settings are exposed as gain values. While for the shunt voltage
this is straightforward, the bus range settings of 32V (default) and 16V
are mapped to gain values of 1 resp. 2, to provide a uniform API to
userspace.
As the gain settings are incorporated into the raw values by the sensor
itself, adjusting of the scale attributes is not necessary.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the config uses the physical value corresponding to the LSB
for both the power and the bus voltage register, the shunt voltage is
specified as parts of 1 mV. Use the LSB physical value for all registers.
No functional change.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Lower bits of the INA219/220 bus voltage register are conversion
status flags, properly shift the value.
When reading via IIO buffer, the value is passed on unaltered,
shifting is the responsibility of the user.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Need to acknowledge DRDY irq in direct mode/ software
triggered mode. Otherwise, on the next conversion, overrun
flag will be raised, which is not a correct state.
This doesn't affect the functionality, but will generate
possible incorrect overrun reports.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Added support for DMA transfers. The implementation uses the user watermark
to decide whether DMA will be used or not. For watermark 1, DMA will not be
used. If watermark is bigger, DMA will be used.
Sysfs attributes are created to indicate whether the DMA is used,
with hwfifo_enabled, and the current DMA watermark is readable
in hwfifo_watermark. Minimum and maximum values are in hwfifo_watermark_min
and hwfifo_watermark_max.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The module license checker complains about these two so just fix
it up. They are both GPLv2, both written by me or using code
I extracted while refactoring from the GPLv2 drivers.
Cc: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
-----BEGIN PGP SIGNATURE-----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=IXO+
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third set of new device support, cleanups and features for IIO in the 4.15 cycle
New device support
* ti-dac082s085 dac
- new driver supporting 8, 10 and 12 bit TI DACs with 2 and 4 channels:
DAC082S085, DAC102S085, DAC122S085, DAC104s085 and DAC124S085.
Minor features and cleanps
* adc12138
- make array ch_to_mux static for small object code size reduction.
* sun4i-gpadc
- use of_device_get_match_data rather than opencoding it.
* stm32 trigger
- add tim15 tigger on STM32H7
- check clock rate to avoid potential division by zero
* tsl2x7x staging cleanups.
- move *_thresh_period to being created by IIO core.
- remove unused tsl2x7x_parse_result structure.
- sort includes
- drop a repeat iio_dev forward definition
- fix some code alignment of defines.
- use IIO_CONST_ATTR for constant string attribute
- drop some unnecessary parentheses
- fix various alignment with parenthese
- rename power defines for readability reasons
- fix a missaligned break statement
- Tidy up function definitions so they fit on a single line.
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() return NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate const array ch_to_mux on the stack, instead
make it static. Makes the object code smaller by over 200 bytes:
Before:
text data bss dec hex filename
12663 1648 128 14439 3867 drivers/iio/adc/ti-adc12138.o
After
text data bss dec hex filename
12353 1744 128 14225 3791 drivers/iio/adc/ti-adc12138.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add check on STM32 ADC clock rate to report an explicit error.
This may avoid division by 0 later in stm32-adc driver.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add TIM15_TRGO trigger that is now supported on STM32H7.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This fix allows platforms to probe correctly even if the
trigger edge property is missing. The hardware trigger
will no longer be registered in the sybsystem
Preserves backwards compatibility with the support that
was in the driver before the hardware trigger.
https://storage.kernelci.org/mainline/master/v4.14-rc2-255-g74d83ec2b734/arm/sama5_defconfig/lab-free-electrons/boot-at91-sama5d2_xplained.txt
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Fixes: 5e1a1da0f ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These ADCs are marketed as single-channel 22 bit delta-sigma ADCs, but
in reality their resolution is 21 bit with an overrange or underrange
of 12% beyond Vref. In other words, "full scale" means +/- 2^20.
This driver does not explicitly signal back to the user when an
overrange or underrange occurs, but the user can detect it by comparing
the raw value to +/- 2^20 (or the scaled value to Vref).
The chips feature an extended temperature range and high accuracy,
low noise characteristics, but their conversion times are slow with
up to 80 ms +/- 2% (on the MCP3550-50).
Hence, unlike the other ADCs supported by the driver, conversion does
not take place in realtime upon lowering CS. Instead, CS is asserted
for 8 usec to start the conversion. After waiting for the duration of
the conversion, the result can be fetched. While waiting, control of
the bus is ceased so it may be used by a different device.
After the result has been fetched and 10 us have passed, the chip goes
into shutdown and an additional power-up delay of 144 clock periods is
then required to wake the analog circuitry upon the next conversion
(footnote below table 4-1, page 16 in the spec).
Optionally, the chips can be used in so-called "continuous conversion
mode": Conversions then take place continuously and the last result may
be fetched at any time without observing a delay. The mode is enabled
by permanently driving CS low, e.g. by wiring it to ground. The driver
only supports "single conversion mode" for now but should be adaptable
to "continuous conversion mode" with moderate effort.
The chips clock out a 3 byte word, unlike the other ADCs supported by
the driver which all have a lower resolution than 16 bit and thus make
do with 2 bytes. Calculate the word length on probe by rounding up the
resolution to full bytes. Crucially, if the clock idles low, the
transfer is preceded by a useless Data Ready bit which increases its
length from 24 bit to 25 bit = 4 bytes (section 5.5 in the spec).
Autosense this based on the SPI slave's configuration.
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
According to the ABI documentation, the shunt resistor value should be
specificied in Ohm. As this is also used/documented for the MAX9611,
use the same for the INA2xx driver.
This poses an ABI break for anyone actually altering the shunt value
through the sysfs interface, it does not alter the default value nor
a value set from the devicetree.
Minor change: Fix comment, 1mA is 10^-3A.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the of_device_get_match_data() helper instead of open coding.
Note that the rcar-gyroadc driver is used with DT only, so there's
always a valid match.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The rcar-gyroadc driver compiles fine on other platforms, hence increase
compile coverage.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On 64-bit:
drivers/iio/adc/rcar-gyroadc.c: In function 'rcar_gyroadc_parse_subdevs':
drivers/iio/adc/rcar-gyroadc.c:352:15: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
childmode = (unsigned int)of_id->data;
^
Cast the pointer to uintptr_t instead of unsigned int to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Before this patch, forgetting to put a thermal-zones DT node would
result in the driver failing to probe.
It should be perfectly acceptable to have the driver probe even if no
thermal-zones DT is found. However, it shouldn't want to fail if the
thermal registering fail for any other reason (waiting for other drivers
for example) so check on ENODEV only.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver has a get_temp function used by the thermal framework that
uses pm functions.
However, the driver isn't registered in pm before it is registered in
thermal framework, resulting in the pm_resume not being called and thus
the IP not enabled.
When the IP is disabled, the raw temp value is always 0. With the
devices currently supported, it isn't a problem since with their
respective formula, they return a really cold SoC temperature which
isn't a problem for the thermal framework. But for future SoC that have
a different formula, it could return a critically hot temperature,
forcing the thermal framework to shutdown the board.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The dln2-adc driver uses interface(s) that are controlled by the
IIO_TRIGGERED_BUFFER Kconfig symbol, so the driver needs to select
that symbol to prevent the build error.
drivers/iio/adc/dln2-adc.o: In function `dln2_adc_probe':
dln2-adc.c:(.text+0x528): undefined reference to `devm_iio_triggered_buffer_setup'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: linux-iio@vger.kernel.org
Cc: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements have gone away.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlnH4XkRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0Fogkaw//e3z+4TQT2Hn+550lBYUV8pBR5emDiSe3
0QTG+ZS7Kh+fPYENLCXtW9ttZicmUSqkTQFvlMTjAxHyj9XzL7+BXS9UlNgVLsqX
pn9KprPj31lrXpJOXMSgcdiqWMZLtCvprAJgnwfZt1GevS3WbCMmnnoaBuJV61jp
w0VD+forukTGF7b0OMGB0d5mwtYS0bJYqXRRMPD+2bNeM4hqt5YM3+wHSqP35t3l
MoaqKlbx7ZtKDF4zIa59nKNP7Ky7IByWogLZRlJ/vD/uKrACckPT22+KT8rX2TwA
NpZb1Oy/KZBTl5D9iRjZADq4NaRJENFXJiG6GkjoGjrQhUqHaCinHWpLioqLGlRq
qCPL2nRjqm4Qr7E8sxlwR1Ajlg0utBMY7Oflym/XJMMLF/ZE6HSrzyrxuVMG2EjV
T7SVIncbfg6kyr/r4kKsAT3BUMV+TdO4sXm+JgphZBUqZLp0nFHnmjP7Rm2j2uWq
+yLrSuF25RijrRj3sp28zg9dFWlRwRvZvcAx8kEGm1kMjMWr+Q10xTK9o/5LlFEw
57sUm6qgmigPK8sahDtcdLIwaCPVvAYvJ0e4Mfw5UsPSlZmHmM1mLwjpwiXBZ5ig
oxnJmTXsn5RcOGiW/mg0VCH26NkBx7H0fsRqQeq9wkxHLrm75vXroIn7YqRIg+Ad
/Itu6x6fOIg=
=ik5C
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Round one of new device support, features and cleanup for IIO in the 4.15 cycle.
Note there is a misc driver drop in here given we have support
in IIO and the feeling is no one will care.
A large part of this series is a boiler plate removal series avoiding
the need to explicitly provide THIS_MODULE in various locations.
It's very dull but touches all drivers.
New device support
* ad5446
- add ids to support compatible parts DAC081S101, DAC101S101,
DAC121S101.
- add the dac7512 id and drop the misc driver as feeling is no
one is using it (was introduced for a board that is long obsolete)
* mt6577
- add bindings for mt2712 which is fully compatible with other
supported parts.
* st_pressure
- add support for LPS33HW and LPS35HW with bindings (ids mostly).
New features
* ccs811
- Add support for the data ready trigger.
* mma8452
- remove artifical restriction on supporting multiple event types
at the same time.
* tcs3472
- support out of threshold events
Core and tree wide cleanup
* Use macro magic to remove the need to provide THIS_MODULE as part of
struct iio_info or struct iio_trigger_ops. This is similar to
work done in a number of other subsystems (e.g. i2c, spi).
All drivers are fixed and then the fields in these structures are
removed.
This will cause build failures for out of tree drivers and any
new drivers that cross with this work going into the kernel.
Note mostly done with a coccinelle patch, included in the series
on the mailing list but not merged as the fields no longer exist
in the structures so the any hold outs will cause a build failure.
Cleanups
* ads1015
- avoid writing config register when it doesn't change.
- add 10% to conversion wait time as it seems it is sometimes
a little small.
* ade7753
- replace use of core mlock with a local lock. This is part of a
long term effort to make the use of mlock opaque and single
purpose.
* ade7759
- expand the use of buf_lock to cover previous mlock cases. This
is a slightly nicer solution to the same issue as in ade7753.
* cros_ec
- drop an unused variable
* inv_mpu6050
- add a missing break in a switch for consistency - not actual
bug,
- make some local arrays static to save on object code size.
* max5481
- drop manual setting of the spi module owner as handled by the
spi core.
* max5487
- drop manual setting of the spi module owner as handled by the
spi core.
* max9611
- drop explicit setting of the i2c module owner as handled by
the i2c core.
* mcp320x
- speed up reads on single channel devices,
- drop unused of_device_id data elements,
- document the struct mcp320x,
- improve binding docs to reflect restrictions on spi setup and
to make it explicit that the reference regulator is needed.
* mma8452
- symbolic to octal permissions,
- unsigned to unsigned int.
* st_lsm6dsx
- avoid setting odr values multiple times,
- drop config of LIR as it is only ever set to the existing
defaults,
- drop rounding configuration as it only ever matches the defaults.
* ti-ads8688
- drop manual setting of the spi module owner as handled by the
spi core.
* tsl2x7x
- constify the i2c_device_id,
- cleanup limit checks to avoid static checker warnings (and generally
have nicer code).
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
-----BEGIN PGP SIGNATURE-----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=CcjQ
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First round of IIO fixes for the 4.14 cycle
Note this includes fixes from recent merge window. As such the tree
is based on top of a prior staging/staging-next tree.
* iio core
- return and error for a failed read_reg debugfs call rather than
eating the error.
* ad7192
- Use the dedicated reset function in the ad_sigma_delta library
instead of an spi transfer with the data on the stack which
could cause problems with DMA.
* ad7793
- Implement a dedicate reset function in the ad_sigma_delta library
and use it to correctly reset this part.
* bme280
- ctrl_reg write must occur after any register writes
for updates to take effect.
* mcp320x
- negative voltage readout was broken.
- Fix an oops on module unload due to spi_set_drvdata not being called
in probe.
* st_magn
- Fix the data ready line configuration for the lis3mdl. It is not
configurable so the st_magn core was assuming it didn't exist
and so wasn't consuming interrupts resulting in an unhandled
interrupt.
* stm32-adc
- off by one error on max channels checking.
* stm32-timer
- preset should not be buffered - reorganising register writes avoids
this.
- fix a corner case in which write preset goes wrong when a timer is
used first as a trigger then as a counter with preset. Odd case but
you never know.
* ti-ads1015
- Fix setting of comparator polarity by fixing bitfield definition.
* twl4030
- Error path handling fix to cleanup in event of regulator
registration failure.
- Disable the vusb3v1 regulator correctly in error handling
- Don't paper over a regulator enable failure.
The serial interface can be reset by writing 32 consecutive 1s to the device.
'ret' was initialized correctly but its value was overwritten when
ad7793_check_platform_data() was called. Since a dedicated reset function
is present now, it should be used instead.
Fixes: 2edb769d24 ("iio:ad7793: Add support for the ad7798 and ad7799")
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since most of the SD ADCs have the option of reseting the serial
interface by sending a number of SCLKs with CS = 0 and DIN = 1,
a dedicated function that can do this is usefull.
Needed for the patch: iio: ad7793: Fix the serial interface reset
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
returns a signed voltage from mcp320x_adc_conversion() but neglects that
the caller interprets a negative return value as failure. Only mcp3301
(and the upcoming mcp3550/1/3) is affected as the other chips are
incapable of measuring negative voltages.
Fix and while at it, add mcp3301 to the list of supported chips at the
top of the file.
Fixes: f686a36b4b ("iio: adc: mcp320x: Add support for mcp3301")
Cc: Andrea Galbusera <gizero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver calls spi_get_drvdata() in its ->remove hook even though it
has never called spi_set_drvdata(). Stack trace for posterity:
Unable to handle kernel NULL pointer dereference at virtual address 00000220
Internal error: Oops: 5 [#1] SMP ARM
[<8072f564>] (mutex_lock) from [<7f1400d0>] (iio_device_unregister+0x24/0x7c [industrialio])
[<7f1400d0>] (iio_device_unregister [industrialio]) from [<7f15e020>] (mcp320x_remove+0x20/0x30 [mcp320x])
[<7f15e020>] (mcp320x_remove [mcp320x]) from [<8055a8cc>] (spi_drv_remove+0x2c/0x44)
[<8055a8cc>] (spi_drv_remove) from [<805087bc>] (__device_release_driver+0x98/0x134)
[<805087bc>] (__device_release_driver) from [<80509180>] (driver_detach+0xdc/0xe0)
[<80509180>] (driver_detach) from [<8050823c>] (bus_remove_driver+0x5c/0xb0)
[<8050823c>] (bus_remove_driver) from [<80509ab0>] (driver_unregister+0x38/0x58)
[<80509ab0>] (driver_unregister) from [<7f15e69c>] (mcp320x_driver_exit+0x14/0x1c [mcp320x])
[<7f15e69c>] (mcp320x_driver_exit [mcp320x]) from [<801a78d0>] (SyS_delete_module+0x184/0x1d0)
[<801a78d0>] (SyS_delete_module) from [<80108100>] (ret_fast_syscall+0x0/0x1c)
Fixes: f5ce4a7a92 ("iio: adc: add driver for MCP3204/08 12-bit ADC")
Cc: Oskar Andero <oskar.andero@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit adds mt2712 compatible node.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix a bad error check when counting 'st,adc-channels' array elements.
This is seen when all channels are in use simultaneously.
Fixes: 64ad7f643 ("iio: adc: stm32: introduce compatible data cfg")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If we can not enable the regulator, go through the error handling path
instead of silently continuing.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Commit 7cc97d77ee has introduced a call to 'regulator_disable()' in the
.remove function.
So we should also have such a call in the .probe function in case of
error after a successful 'regulator_enable()' call.
Add a new label for that and use it.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If 'devm_regulator_get()' fails, we should go through the existing error
handling path instead of returning directly, as done is all the other
error handling paths in this function.
Fixes: 7cc97d77ee ("iio: adc: twl4030: Fix ADC[3:6] readings")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver sets a .data pointer for each .compatible string but never
calls of_device_get_match_data(). Instead, ADC properties are looked up
with spi_get_device_id(). The .data pointer is therefore unnecessary,
so drop it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Single-channel converters such as mcp3001, mcp3201, mcp3301 and the
upcoming mcp3550/1/3 lack a MOSI pin, so there's no need to call
mcp320x_channel_to_tx_data() for them.
Moreover, instead of calling spi_read() for these converters, which
generates an spi_message and spi_transfer on the stack on every readout,
it's more efficient to use the spi_message and spi_transfer[] included
in struct mcp320x (as we do for multi-channel ADCs), but initialize the
spi_message only with the receive transfer.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
STM32 ADC supports hardware triggers like STM32 Low-Power Timer.
For instance, STM32H7 ADC may be triggered by instances 1, 2 or 3.
Add hardware triggered mode so Low-Power Timer Trigger driver can
validate device.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
As user's guide "ADS1015EVM, ADS1115EVM, ADS1015EVM-PDK, ADS1115EVM-PDK
User Guide (Rev. B)" (http://www.ti.com/lit/ug/sbau157b/sbau157b.pdf)
states at page 16:
"Note that both the ADS1115 and ADS1015 have internal clocks with a ±10%
accuracy. If performing FFT tests, frequencies may appear to be incorrect
as a result of this tolerance range.", add those 10% to converion wait
time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is no point writing ADS1015_CFG_REG when configuration
didn't change. Avoid that.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This has been handled by the spi core for some time now.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This has been handled by the i2c core for some time.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
The comparator polarity field in config register is not correctly
initialized as per the interrupt trigger setting. Because the bitfield
definision is wrong and bit shifting is missed.
Fixes: d9f39babd8 ("iio: adc: ti-ads1015: add threshold event support")
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlmZpCcRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FohlmQ/6A9FAI0wPGeEQCXDiLtIAWI1/DByYsHDk
P3U6sFS17y56KAQcLS34HVR5lLreHya3hsUmPl4gCsjXZsGWAinyXy74BNtBbPmx
LtzVsyLdjBP3Nxl/OGgNWG+kiq7Op+uw0/OZohtEqzurG0142S6CVvxteFlmhQNH
pLlmPGnwk6Z4GsasHma/f2FkDD8oRVgvQSP7dJ9HIwq49qQ76cT/+20X1xODHLGw
qpXfQiLUFW8E1JBTDDcXZD3M23TWG4DZcVlNnWf8fja/bk4WaLBKqVrI9gGZpZsQ
xXfrSDRwc216w6tzVWjsNV/M0ZuSdm/VCBeyQa17XQVNelkO4dVrCqFMLCh5i/t5
p4qhhV9mrbweIgDj++6c+4qMzWSAznWybAKMMlcucmwxHKefcrlgUniE03OzyPpG
gpMS94enlVW8WpE/iYkxb/d6EqTM9CH2CJH6W4Ve/Xr4aQHkF5/P23k+nsW113of
T1q1SCKegV9p7hIzqDqDmOQC7iNTcBcu+/7RYtkDn9jmmhiQAxwoPJZunkR1cxD8
hA04x5W9HuPFdbNRlH1MozClbyRUtk0L/XLTKwA9T0VyRUKV1P6Szcp9wYRw+6G8
QiA5NNrNPf17L6slLZ06N1auu6vO7BhTmYNKnd6VBO+vi7kF/FM2UdZGHof4WT/4
zPE/BO8IwTk=
=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-iio@vger.kernel.org
Cc: linux-rockchip@lists.infradead.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1015 device provides programmable comparator that can issue an
interrupt on the ALERT pin. This change adds the iio threshold event
support for that feature.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, comparator settings, and etc. So only a
single event channel can be enabled at a time. Also enabling both buffer
and event are prohibited for simplicity.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
While the iio buffer for the ti-ads1015 driver is enabled, reading the
raw ADC channel data is restricted. We usually use the
iio_device_claim_direct_mode()/iio_device_release_direct_mode() pair for
that.
This change consequently reverses the locking order for the driver's
private lock and indio_dev->mlock which acquired by
iio_device_claim_direct_mode() internally. But it's safe because there is
no other dependency between these locks.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_iio_triggered_buffer_setup to simplify the error path in the
probe() and remove() function.
This changes the remove order, but the end result of remove function
actually does the reverse of probe.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This adds a helper function to set conversion mode as there are a fair
number of users.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own scale information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's scale information immediately overwrites the current PGA
setting in the config register.
It is harmless because the correct PGA settings are reloaded just before
getting adc result anyway. But it is unnecessary register update and
should be removed.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
inserts a wait time before reading the conversion register if the
configuration is changed from a previous request.
Currently, the wait time is only the period required for a single
conversion that is calculated as the reciprocal of the sampling frequency.
However we also need to wait for the the previous conversion to complete.
Otherwise we probably get the conversion result for the previous
configuration when the sampling frequency is lower.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
pm_runtime_get_sync() and pm_runtime_put_autosuspend() return 0 on
success, 1 if the device's runtime PM status was already requested status
or error code on failure. So a positive return value doesn't indicate an
error condition.
However, any non-zero return values from buffer preenable and postdisable
callbacks are recognized as an error and this driver reuses the return
value from pm_runtime_get_sync() and pm_runtime_put_autosuspend() in
these callbacks. This change fixes the false error detections.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver assumes that the device is operating in the continuous
conversion mode which performs the conversion continuously. So this driver
doesn't insert a wait time before reading the conversion register if the
configuration is not changed from a previous request.
This assumption is broken if the device is runtime suspended and entered
a power-down state. The forthcoming request causes reading a stale result
from the conversion register as the device is runtime resumed just before.
Fix it by adding a flag to detect that condition and insert a necessary
wait time.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADS1015 device have two operating modes, continuous conversion mode
and single-shot mode. This driver assumes that the continuous conversion
mode is selected by runtime resume callback when the ADC result is
requested.
If CONFIG_PM is disabled, the device is always in the default single-shot
mode and no one begins a single conversion. So the conversion register
doesn't contain valid ADC result. Fix it by changing the continuous mode
in probe function.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver supports ADS1015 and ADS1115 devices. The same
scale information is used for both devices in this driver, however they
have actually different values and the ADS1115's one is not correct.
These devices have the same full-scale input voltage range for each PGA
selection. So instead of adding another hardcoded scale information,
compute a correct scale on demand from each device's resolution.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ti-ads1015 driver has eight iio voltage channels and each iio channel
can hold own sampling frequency information.
The ADS1015 device only have a single config register which contains an
input multiplexer selection, PGA and data rate settings. So the driver
should load the correct settings when the input multiplexer selection is
changed.
However, regardless of which channlel is currently selected, changing any
iio channel's sampling frequency information immediately overwrites the
current data rate setting in the config register.
It breaks the current data rate setting if the different channel's sampling
frequency information is changed because the data rate setting is not
reloaded when the input multiplexer is switched.
This removes the unexpected config register update and correctly load the
data rate setting before getting adc result.
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ACPI enabled platforms do not have a mean of regulators. Instead we use
hard coded voltage value for reference pin. When value is 0 (default) we
fall back to request a regulator.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Without the triggered buffer code, we get a link error:
drivers/iio/adc/at91-sama5d2_adc.o: In function `at91_adc_probe':
at91-sama5d2_adc.c:(.text+0x938): undefined reference to `devm_iio_triggered_buffer_setup'
This adds a Kconfig 'select' statement like other ADC
drivers have it already.
Fixes: 5e1a1da0f8 ("iio: adc: at91-sama5d2_adc: add hw trigger and buffer support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch fix following checkpatch warnings in xadc driver
1. prefer 'unsigned int' to bare use of 'unsigned'.
2. else is not generally useful after a break or return.
3. fill all function definition arguments with identifier name
Signed-off-by: Sai Krishna Potthuri <lakshmis@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
SPI device registered via OF will always match a legacy SPI device ID and
that the MODALIAS reported will always be of the form spi:<device>.
There is an ACPI method to enumerate such devices via specific ACPI ID
and use of compatible strings. It will not work for the drivers which
have no OF match ID table present.
Besides this could change in the future so the correct approach is to
have an OF device ID table if the devices are registered via OF.
Tested-by: David Lechner <david@lechnology.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
STM32 ADC allows each channel to be sampled with a different sampling time,
by setting SMPR registers. Basically, value depends on local electrical
properties. Selecting correct value for sampling time highly depends on
analog source impedance. There is a manual that may help in this process:
'How to get the best ADC accuracy in STM32...'
This patch allows to configure minimum sampling time via device tree,
either for:
- all channels at once:
st,min-sample-time-nsecs = <10000>;
- independently for each channel (must match "st,adc-channels" list):
st,adc-channels = <0 1>;
st,min-sample-time-nsecs = <5000 10000>;
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC clock input is provided to internal prescaler (that decreases its
frequency). It's then used as reference clock for conversions.
- Fix common clock rate used then by stm32-adc sub-devices. Take common
prescaler into account. Currently, rate is used to set "boost" mode.
It may unnecessarily be set. This impacts power consumption.
- Fix ADC max clock rate on STM32H7 (fADC from datasheet). Currently,
prescaler may be set too low. This can result in ADC reference
clock used for conversion to exceed max allowed clock frequency.
Fixes: 95e339b6e8 ("iio: adc: stm32: add support for STM32H7")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Proper support for the INA219 lowered the minimum sampling period from
2*140us to 2*84us. Subtracting 200us later leads to an underflow and
an almost infinite udelay later.
Using a signed int for the sampling period provides sufficient range
(at most 2*8640*1024us), but catches the underflow when comparing with
buffer_us.
Fixes: 18edac2e22 ("iio: adc: Fix integration time/averaging for INA219/220")
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAll3oWIRHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FoimeBAAs2WBPr8kQZeDfdjNS5isk+GoBJ4btHDL
+BpBODylDku/WIJb7hpBymH2Xs/7qUuYLYwz0P1XVrSo/1kK+krJQR0DUwcracfy
gqMS4KEmgWbhmBV2ksPfCGcoT5rimxLUqpka5+WWAszNtwi7YOt5FadTb9yK4WdG
Di5AzaVLKAUBpQrrHdFPXewxenVs1P/X0ES7fSNU1SIL2bRAaPDj9duu3URivt9l
XRh7qqNpuNMIQ3MmeEeLDJkyeeeWHYdnps/XDfW0i5VElxwZImTPD+AFAoc2E51J
pujvXlu1a6FgMH+hp7hbOxNuf3eKlIq9mrfGre4K6DkTB0gro3oU2bCa5BEq/be1
PrKQZsfkK0KmrLCh0UqwTTcWdorOfussWpZ6Ib4/l4JQEeII/odwyZJ3vHNlm0Gy
0n/TVfNVQEY2zLswWdUOaQ2bvLGaXoeIBH0sMtCPOKks/4u692qZg3LAC1g5mEKF
4ykKG8oJ/UvWcqb00Z1H1qkT+B0ZmOEZzf6M7rFlPKr48DHrbu1YZcoaPYoBxeWP
nL9S0zdygs06HI3/5Rl4Vv7HMTCbKabOp7eamW3IDqRpcW6dLzsXrG/e3YFbvMxq
sGfd3g8jXaf1rlA9qP5FOHdQM2ySoi/WliwShH46LTY17sHSwQd46FYDKn4ZMT4q
6oMBnYOeadg=
=imPz
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of IIO new device support, features and cleanups for the 4.14 cycle.
4 completely new drivers in this set and plenty of other stuff.
One ABI change due to a silly mistake a long time back. Hopefully no
one will notice. It effects the numerical order of consumer device
channels which was the reverse of the obvious. It's going the slow
way to allow us some margin to spot if we have broken userspace or
not (seems unlikely)
New Device Support
* ccs811
- new driver for the Volatile Organic Compounds (VOC) sensor.
* dln2 adc
- new driver for the ADC on this flexible usb board.
* EP93xx
- new driver for this Cirrus logic SoC ADC.
* ltc2471
- new ADC driver support the ltc2471 and ltc2473
* st_accel
- add trivial table entries to support H3LIS331DL, LIS331DL, LIS3LV02DL.
* st_gyro
- add L3GD20H support (again) having fixed the various things that were
broken in the first try. Includes devicetree binding.
* stm32 dac
- add support for the DACs in the STM32F4 series
Features
* Documentation
- add missing power attribute documentation to the ABI docs.
* at91-sama5d2
- add hardware trigger and buffered capture support with bindings.
- suspend and resume functionality.
* bmc150
- support for the BOSC0200 ACPI device id seen on some tablets.
* hdc100x
- devicetree bindings
- document supported devices
- match table and device ids.
* hts221
- support active low interrupts (with bindings)
- open drain mode with bindings.
* htu21
- OF match table and bindings.
* lsm6dsx
- open drain mode with bindings
* ltc2497
- add support for board file based consumer mapping.
* ms5367
- OF match table and bindings.
* mt7622
- binding document and OF match table.
- suspend and resume support.
* rpr0521
- triggered buffer support.
* tsys01
- OF match table and bindings.
Cleanups and minor fixes
* core
- fix ordering of IIO channels to entry numbers when using
iio_map_array_register rather than reversing them.
- use the new %pOF format specifier rather than full name for the
device tree nodes.
* ad7280a
- fix potential issue with macro argument reuse.
* ad7766
- drop a pointless NULL value check as it's done in the gpiod code.
* adis16400
- unsigned -> unsigned int.
* at91 adc
- make some init data static to reduce code size.
* at91-sama5d2 ADC
- make some init data static to reduce code size.
* da311
- make some init data static to reduce code size.
* hid-sensor-rotation
- drop an unnecessary static.
* hts221
- refactor the write_with_mask code.
- move the BDU configuration to probe time as there is no reason for it
to change.
- avoid overwriting reserved data during power-down. This is a fix, but
the infrastructure need was too invasive to send it to mainline except
in a merge window. It's not a regression as it was always wrong.
- avoid reconfigure the sampling frequency multiple times by just
doing it in the write_raw function directly.
- refactor the power_on/off calls into a set_enable.
- move the dry-enable logic into trig_set_state as that is the only
place it was used.
* ina219
- fix polling of ina226 conversion ready flag.
* imx7d
- add vendor name in kconfig for consistency with similar parts.
* mcp3422
- Change initial channel to 0 as it feels more logical.
- Check for some errors in probe.
* meson-saradc
- add a check of of_match_device return value.
* mpu3050
- allow open drain for any interrupt type.
* rockchip adc
- add check on of_match_device return value.
* sca3000
- drop a trailing whitespace.
* stm32 adc
- make array stm32h7_adc_ckmodes_spec static.
* stm32 dac
- fix an error message.
* stm32 timers
- fix clock name in docs to match reality after changes.
* st_accel
- explicit OF table (spi).
- add missing entries to OF table (i2c).
- rename of_device_id table to drop the part name.
- adding missing lis3l02dq entry to bindings.
- rename H3LIS331DL_DRIVER_NAME to line up with similar entries in driver.
* st_gyro
- explicit OF table (spi).
* st_magn
- explicit OF table (spi).
- enable multiread for lis3mdl.
* st_pressure
- explicit OF table (spi).
* st_sensors common.
- move st_sensors_of_i2c_probe and rename to make it available for spi
drivers.
* tsc3472
- don't write an extra byte when writing the ATIME register.
- add a link to the datasheet.
* tsl2x7x - continued staging cleanups
- add of_match_table.
- drop redundant power_state sysfs attribute.
- drop wrapper tsl2x7x_i2c_read.
- clean up i2c calls made in tsl2x7x_als_calibrate.
- refactor the read and write _event_value callbacks to handle additional
elements.
- use usleep_range instead of mdelay.
- check return value from tsl2x7x_invoke_change.
* zpa2326
- add some newline to the end of logging macros.
New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
This patch enables adc engine at initialization time and waits
for the initial sequence completion before enabling adc channels.
Without this code adc channels are not functional and shows
zeros for all connected channels.
Tested on mellanox msn platform.
v1 -> v2:
Pointed by Rick Altherr:
- Wait init sequence code enabled by bool
from OF match table.
Signed-off-by: Mykola Kostenok <c_mykolak@mellanox.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-iio@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Don't populate array startup_lookup on the stack but instead make
it static. Makes the object code smaller.
Before:
text data bss dec hex filename
21754 5440 128 27322 6aba drivers/iio/adc/at91_adc.o
After:
text data bss dec hex filename
21613 5496 128 27237 6a65 drivers/iio/adc/at91_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
I noticed in its DSDT that one of my tablets actually is using the GPADC
pin for temperature monitoring.
The whole axp288_adc_set_ts() function is a bit weird, in the past it was
removed because it seems to make no sense, then this was reverted because
of regressions.
So I decided to test the special GPADC pin handling on this tablet.
Conclusion: not only is axp288_adc_set_ts() necessary, we need to sleep a
bit after making the AXP288_ADC_TS_PIN_CTRL changes before sampling the
GPADC, otherwise it will often (about 80% of the time) read 0 instead of
its actual value.
It seems that there is only 1 bias current source and to be able to use it
for the GPIO0 pin in GPADC mode it must be temporarily turned off for the
TS pin, but the datasheet does not mention this.
This commit adds a sleep after disabling the TS pin bias current,
fixing the GPADC more often then not wrongly returning 0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Making the const array startup_lookup static rather having it on the
stack saves 69 bytes. Add in missing int specifier to clean up a
checkpatch warning.
Before:
text data bss dec hex filename
10297 2800 128 13225 33a9 drivers/iio/adc/at91-sama5d2_adc.o
After:
text data bss dec hex filename
10140 2888 128 13156 3364 drivers/iio/adc/at91-sama5d2_adc.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return value from call to of_match_device()
in order to prevent a NULL pointer dereference.
In case of NULL print error message and return -ENODEV
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This patch adds support for Diolan DLN2 ADC via IIO's ADC interface.
ADC is the fourth and final component of the DLN2 for the kernel.
Signed-off-by: Jack Andersen <jackoalan@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to select the alternate voltage reference pair (VALTH/VALTL), the
right value for the REFSEL field in the ADCx_CFG register is "01", leading
to 0x800 as register mask. See section 8.2.6.4 in the reference manual[1].
[1] http://www.nxp.com/docs/en/reference-manual/VFXXXRM.pdf
Fixes: a775427632 ("iio:adc:imx: add Freescale Vybrid vf610 adc driver")
Signed-off-by: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The LTC2741 and LTC2473 are single voltage ADC chips. The LTC2473
is similar to the LTC2471 but outputs a signed differential value.
Datasheet:
http://cds.linear.com/docs/en/datasheet/24713fb.pdf
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Inheriting the ADC BIAS current settings from the BIOS instead of
hardcoding then causes the AXP288 to disable charging (I think it
mis-detects an overheated battery) on at least one model tablet.
So lets go back to hard coding the values, this reverts
commit fa2849e964 ("iio: adc: axp288: Drop bogus
AXP288_ADC_TS_PIN_CTRL register modifications"), fixing charging not
working on the model tablet in question.
The exact cause is not fully understood, hence the revert to a known working
state.
Cc: stable@vger.kernel.org
Reported-by: Umberto Ixxo <sfumato1977@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When initializing interrupts, the devm_request_any_context_irq will
enable them right away. An atomic flag was set in sun4i_irq_init and read
in the interrupt handler to make sure no unwanted interrupts were
handled. If an unwanted interrupt occurred, the handler would disable
the irq and return IRQ_HANDLED. However, at the end of sun4i_irq_init,
the irq would be disabled as well, resulting in an unbalanced enable
(since there are more disables than enables, the code enabling the
interrupt would never be called).
When reading the ADC or the temperature, the respective irq would be
enabled in the read function and disabled in the irq handler. In the
read function, we would wait for a completion (with a timeout) that will
be set in the irq handler. However, if the completion is never set or if
the wait for completion times out, the irq would not be disabled in the
read function resulting in an unbalanced enable once the read function
is called again (since there are 2+ enables for no disable).
Moving disable_irq from the irq handler to the read function get rid of
these two cases of unbalanced enable.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Reported-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv drivers
- Minor fixes and cleanups in various drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=J5ye
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add PMBus client driver for IR35221
- Add support for NCT6795D to nct6775 driver
- Functional improvements to adt7475, aspeed-pwm-tacho, and ibmpowernv
drivers
- Minor fixes and cleanups in various drivers
* tag 'hwmon-for-linus-v4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (22 commits)
hwmon: (aspeed-pwm-tacho) Poll with short sleeps.
hwmon: (aspeed-pwm-tacho) reduce fan_tach period
hwmon: (ibmpowernv) Add current(A) sensor
hwmon: (ibmpowernv) introduce a legacy_compatibles array
hwmon: (pwm-fan) Switch to new atomic PWM API
hwmon: (scpi) Fix the scale of SCP sensor readings
hwmon: (aspeed-pwm-tacho) Enable both edge measurement.
hwmon: (ibmpowernv) Add highest/lowest attributes to sensors
hwmon: (pmbus) move header file out of I2C realm
hwmon: (max6639) move header file out of I2C realm
hwmon: (ltc4245) move header file out of I2C realm
hwmon: (ds620) move header file out of I2C realm
hwmon: (ads1015) move header file out of I2C realm
hwmon: (adt7475) temperature smoothing
hwmon: (adt7475) add high frequency support
hwmon: (adt7475) fan stall prevention
hwmon: (adt7475) replace find_nearest() with find_closest()
hwmon: (pmbus) Add client driver for IR35221
hwmon: (nct6775) Add support for NCT6795D
hwmon: (nct6775) Improve fan detection
...
Add missing hooks in the LTC2497 IIO driver to allow hwmon mapping.
Signed-off-by: Gaurav Gupta <gauragup@cisco.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The array stm32h7_adc_ckmodes_spec does not need to be in global scope, so
make it static.
Cleans up sparse warning:
"symbol 'stm32h7_adc_ckmodes_spec' was not declared. Should it be static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Some part of the configuration are not touched after the probe
and if something goes wrong on writing the initial one,
the chip will misbehave.
Adding an error checking ensures that the inital configuration will
be written correctly. Moreover ensures that a sensible configuration
will be saved in driver data and used subsequently as intended.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Initial channel should be the first available channel on
all configurations, so changing to channel 0 available on
all supported chips.
Signed-off-by: Angelo Compagnucci <angelo.compagnucci@gmail.com>
Reported-by: Maarten Brock <m.brock@vanmierlo.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch supports auxadc suspend/resume flow.
Disable auxadc clk and power in suspend function.
Enable axuadc clk and power in resume function.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for suspend/resume functionality for the ADC IP
in sama5d2 SoC.
In order to enter Suspend to ram mode (backup + self refresh mode for
memory), in which the ADC IP is no longer powered, we need to reset the
pins to default state, for the scenario when they are also used for I2C
bus to communicate with the PMIC.
On resume, we need to reconfigure the ADC IP registers and reconfigure the
trigger registers in the case when the suspend procedure is done while
sysfs has the buffer and trigger enabled.
In the case the suspend happens exactly during a software triggered
conversion, the request will time out, because we reset and power down
the ADC.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
While the INA226 has a conversion ready flag (CVRF) in the R/W Mask/Enable
register with read-to-clear semantics, the corresponding bit of the INA219
(CNVR) is part of the bus voltage register. The flag is cleared by reading
the power register.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Added support for the external hardware trigger on pin ADTRG,
integrated the three possible edges into the driver
and created buffer management for data retrieval
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
To keep IMX7D_ADC text consistent with other iio/adc entries, add
the vendor name to the driver menu text.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
-----BEGIN PGP SIGNATURE-----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=2fJI
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.13b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanups for the 4.13 cycle.
A few reverts here. One was a general failure to notice a device was already
supported by another driver. The second is due to a review comment pointing
out that the original patch was a bad idea and would break existing systems.
Reverts
* bma180
- Revert addition of support for the BMA250E it is already supported by
the bmc150-accel and better supported at that. Oops.
* hi8435
- The fix for cleanup of the reset gpio stuff isn't a good way to go. It
breaks systems where an inverting level convertor is used. The right fix
is to make the original devicetree correct - even if it involves patching
the devicetree in kernel.
New Device Support
* stm32-adc
- STM32H7 support and bindings.
Features
* core
- add a hardware triggered operating mode for systems in which the actual
trigger is never seen by the kernel. This is typically only used when
a device 'can' use other triggers, but if a particular magic one is
enabled the interrupt is effectively handled in hardware and we never see
it.
* st-lsm6dsx
- support active low interrupts.
* stm32-adc
- Make the core adc clock optional as not all hardware supported requires it.
- Make the bus clock optional in the per instance driver as it may be shared
by all instances of the ADC and is handled by the core.
- Rework to have a data structure representing the device type specific
elements.
* stm32-trigger (and counter)
- Use the INDIO_HARDWARE_TRIGGERED_MODE where appropriate.
- Add an attribute to configure device modes for quadrature counting etc.
Clean ups and minor fixes
* IIO core.
- use __sysfs_match_string() helper rather than open coding the same.
* ad7791
- use sysfs_match_string() helper rather than open coding the same.
* aspeed-adc
- handle return value of clk_prepare_enable
* cpcap
- Fix default register values and ensure the battery thermistor is enabled
correctly.
- Fix the reported die temperature where we can - docs are lacking.
- Remove the hung interrupt quirk as no longer happens due to fix in the
mfd driver.
* hi8435
- Remove &s from hi8435_info definition as unneeded and inconsistent.
* hid-sensor-trgger
- Add kconfig depends on IIO_BUFFER (fixes patch in previous series)
* ina2xx
- Make the use of iio_info_mask* elements consistent for all channels.
This doesn't have any visible effect, but acts as clear documentation of
which channels various resulting attributes apply to.
* lpc32xx
- handle the return value of clk_prepare_enable.
* meson-saradc
- NULL instead of 0 for pointer.
* mma9551
- use NULL for GPIO connection ID to aid implementation fo ACPI support.
Here the connection ID doesn't actually tell us anything and it is much
easier to deal with the driver if it's not there.
* mpu6050
- Fix lock issues through use of a local mux.
- Replace sprintf with scnprintf as appropriate.
- Check whoami against all known values. This allows for a small number of
boards where we are really fishing for the part not being present at all.
It is unfortunately common to have undescribed changes to use newer chips.
We paper over this but just emitting a warning for those cases as long as
we know about.
* mxs-lradc
- Fix some non static warnings.
* rcar-adc
- Part of making the naming for this part consistent across the kernel.
* st_accel
- drop some spi_device_id entries for variants with no SPI support
* st_magn
- drop some spi_device_id entries for variants with no SPI support.
* sx9500
- Use devm_gpiod_get instead of indexed value with an index of 0 on all
occasions.
* twl4030
- Drop unused twl4030_get_madc_conversion as callers removed now throughout
kernel.
- Unexport twl4030_madc_conversion() as no used only within this driver.
- Drop twl4030_madc_user_params as not used now.
- Drop twl4030_madc_request.func_cb as not used now.
- Fold the twl4030-madc.h header into the driver as no longer used anywhere
else in the kernel.
* xilinx
- Handle the return value of clk_prepare_enable
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Rick Altherr <raltherr@google.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Use sysfs_match_string() helper instead of open coded variant.
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
twl4030-madc.h is no longer used by anything outside of
the iio driver, so it can be merged into the driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This functionality is not used by the IIO subsystem. Due
to removal of legacy API it can also be removed.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
All madc users have been converted to IIO API, so drop the
legacy API. The function is still used inside of the driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Drop legacy twl4030_get_madc_conversion() method. It has been
used by drivers to get madc data before it conversion to IIO
API. There are no users in the mainline kernel anymore.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for STM32H7 Analog to Digital Converter. It has up
to 20 external channels, resolution ranges from 8 to 16bits.
Either bus or asynchronous adc clock may be used.
Add registers & bitfields definition. Also add new configuration
options to enter/exit powerdown and perform self-calibration.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
STM32F4 requires one clock per ADC instance for register access. But,
newer version of ADC hardware block have common bus clock for all
instances (per instance driver isn't responsible for getting it).
So, make it optional by default. Still, enforce it's required on STM32F4.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Prepare support for stm32h7 adc variant by introducing compatible
configuration data.
Move STM32F4 specific stuff to compatible data structure:
- registers & bit fields
- input channels data
- start/stop procedures
- trigger definitions
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Analog clock input is mandatory on stm32f4. But newer version of
ADC hardware block allow to select either bus clock or asynchronous
clock, for analog circuitry.
So, make it optional by default, but enforce clk presence on stm32f4.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
meson_sar_adc_clear_fifo passes a 0 as value-pointer to regmap_read().
In case of the meson-saradc driver this ends up in regmap_mmio_read(),
where the value-pointer is de-referenced unconditionally to assign the
value which was read.
Fix this by passing an actual pointer, even though all we want to do is
to discard the value.
As a side-effect this fixes a sparse warning ("Using plain integer as
NULL pointer") as reported by Paolo Cretaro.
Fixes: 3adbf34273 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Reported-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should
be replaced with NULL test. Also add NULL test for iores.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
INA226/230/231 has integration times per voltage channel and common
averaging setting for both channels, while the INA219/220 only has a
combined integration time/averaging setting per channel.
Only expose the averaging attribute for the INA226, and expose the correct
integration times for the INA219.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix sparse warning: Using plain integer as NULL pointer
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fix sparse warning "symbol foo was not declared. Should it be static?"
for the following symbols:
mx23_lradc_adc_irq_names
mx28_lradc_adc_irq_names
iio_dev_attr_in_voltage0_scale_available
iio_dev_attr_in_voltage1_scale_available
iio_dev_attr_in_voltage2_scale_available
iio_dev_attr_in_voltage3_scale_available
iio_dev_attr_in_voltage4_scale_available
iio_dev_attr_in_voltage5_scale_available
iio_dev_attr_in_voltage6_scale_available
iio_dev_attr_in_voltage7_scale_available
iio_dev_attr_in_voltage10_scale_available
iio_dev_attr_in_voltage11_scale_available
iio_dev_attr_in_voltage12_scale_available
iio_dev_attr_in_voltage13_scale_available
iio_dev_attr_in_voltage14_scale_available
iio_dev_attr_in_voltage15_scale_available
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This reverts commit 61305664a5.
This commit was applied prematurely and will break some existing
situations where the signal is inverted as part of voltage level
conversions.
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Flags for shared channel attributes should be set on all channels of a
channel set. I.e. SAMP_FREQUENCY and OVERSAMPLING_RATIO are set on the
in_voltage{0,1} channels, thus should be set on in_power, in_current.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
C syntax allows apersands when initializing structures fields with
function pointers, but in Linux sources ampersands are normally not used
in thix context.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is no longer needed as the real problem was interrupt flags
not getting passed properly from device tree to the cpcap-core.c
mfd driver. This got fixed with commit ac89473213 ("mfd: cpcap:
Fix interrupt to use level interrupt") So let's remove ADC
interrupt specific the quirk.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Reviewed-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It seems that "MC13783 Power Management and Audio Ciruit User's Guide"
MC1378UG.pdf documents several similar components as in the CPCAP PMIC.
Chapter "9.5.5 Die Temperature and UID" says that the die temperature
value is 282 at 25C with LSB of -1.14C. Converting CPCAP PMIC channel3
values with following seems to produce values that make sense for a
PMIC die:
temperature = 25000 + ((regval - 282) * 114)
As we don't have any other documentation, let's assume the die
temperature is unconfigured in the Motorola mapphone Linux kernel
and the current temperature conversion table should be only used
for the battery thermistor and not for the die temperature.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Looking at the register dumps from Android kernel on droid 4, I noticed
the values with the mainline kernel don't match. Let's fix this by
initializing the ADC registers to what Android does.
For getting correct values from the battery thermistor, we need to
toggle the CPCAP_BIT_THERMBIAS_EN when measuring battery temperature
to get correct battery temperatures. And looks like we also need to
wait a little bit before reading the battery temperature as otherwise
the results are inaccurate.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
-----BEGIN PGP SIGNATURE-----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=XLVY
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 4.13 cycle
Two entirely new drivers in here plus the usual range of cleanups and features.
New device support
* ad5064
- add ltc2631, ltc2633 and ltc2635 support.
* bma180
- trivial support for bma250e (new id)
* hid-sensor-rotation
- add relative orientation and geometric orientation support.
* isl29028
- add isl29030 support (its effectively the same part from a driver point of
view)
* maxim_thermocouple
- add max31856 id.
* meson-saradc
- add meson8b SoC adc support.
* ti-adc084s021
- new driver and bindings.
* ti-adc108s102
- new driver and bindings.
Staging graduations
* isl29028
Features
* bma180
- ACPI enumeration for BMA250E which is used in various x86 tablets.
* hi8453
- add raw access rather than only events.
* hid-sensor-hub
- Implement batch mode in which we can set a threshold on the amount of time
between data coming from the fifos. This is the first device to do this
rather than use a watershed on the number of samples.
* hts221
- power management support
* lsm6dsx
- add system power management support.
* rpr0521
- sampling frequency read / write
* stm32-trigger
- add support for TRG02 triggers.
* tsl2583
- runtime power management support.
Cleanups
* core
- inkern: fix a double unlock in iio_read_available_channel_raw when raw
value doesn't appear to be raw (error path).
- fixup accidental sizeof pointer in iio_device_add_mask_type.
* docs
- fix an accidental duplicated line in sysfs-bus-iio-meas-spec.
* tools
- use local include/uapi headers to ensure always up to date.
- increase length of allowed trigger names.
* ad9834
- symbolic to octal permissions.
* ade7753
- symbolic to octal permissions.
- fix indentation
* ade7754
- symbolic to octal permissions.
* ade7758
- symbolic to octal permissions.
- ade7854
- symbolic to octal permissions.
* as3935
- move out of storm check to given consistent results for raw and processed
values.
* bmp280
- fix bme280 naming in Kconfig help.
* hi8435
- avoid garbage on event after enable.
- add missing in_voltage_sensing_mode_available to list possible enum options.
- handle the reset gpio with the obvious polarity rather than relying on
DT to provide it correctly.
* hid-sensors
- fix a wrong error path scrubbing of return values.
* hid-sensors-accel
- drop static on a local variable
* hid-sensors-rotation
- Add missing scale and offset property parsing support.
* ina2xx
- Fix a bad use of GENMASK and some typos and whitespace issues.
* isl29018
- only declare the ACPI table when ACPI is enabled.
* isl29028
- fix proximity sleep times.
* lsm6dsx
- replace ifdef CONFIG_PM with __maybe_unused to avoid the complexity of
dealing with the various PM config variables.
* meson-saradc
- mark meson_sar_adc_data static and const.
* rcar-gyroadc
- derive the interface clock speed from the fck clock on the basis they are
the same actual clock.
- drop the now unused if clock from the bindings.
* rpr0521
- disable sensor when marked as such rather than always enabling it.
- poweroff if probe fails and we can talk to device.
- make sure device powered off when it doesn't need to be on.
- use sizeof rather than hardcoded size on value read.
- whitespace fixup.
- reorder channel numbers ready for buffered support which didn't quite
make this pull request.
* st-accel
- fix platform data initialization to allow remove and reprobe.
* st-pressure
- fix platform data initialization to allow remove and reprobe.
* tsl2x7x
- S_IRUGO, S_IWUSR to octal values
- rename driver for consistency with more recent drivers
- drop FSF mailing address
- replace DEVICE_ATTR macros with the shorter DEVICE_ATTR_RW form and
relevant function renames.
* zpa2326
- report an error for consistency with other error paths.
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
-----BEGIN PGP SIGNATURE-----
iQJFBAABCAAvFiEEbilms4eEBlKRJoGxVIU0mcT0FogFAlkjMIARHGppYzIzQGtl
cm5lbC5vcmcACgkQVIU0mcT0FojKvA//aDwMkrmHT15IsP6kRWRp8MJ66253YIDK
ZRwr5pu4TXPX6df3HIV7meSi1mYOTX/UHryGsMIx3iwr69jhTQzSf+frZsYVMkLy
IsliKjkbUrkzFlPxicpt4aq1w8xqwkpdWzo27Y1xQMf2UOiNtWSSCRsjBgxr7mmg
Xk5yrvbk4XQ17P/pZrg6NJukSd8XXyJn1Jf9cfBpYfmSwgbRNJZbAmrU3uCtL0li
HK/akyaJYRHVcuv8GdT4eosOd/mw8EkMPe4v5Uv/4p1JWuHJNtCLhEA4AdrMBheK
5GrPpviNRD0aQTvTDRqZW9e2CIwS1UTWYPA+gboOhSkErta36+DnVdVJhVquD3t5
mSifsp2DYC7oMdHtYpihyJClkYm0xNZl/R/cMtroDJzt/nymS9jWgVE4TQEDxpa2
tLbVqre6L9ZOUd+XXvmEyMoPtRELPfmi87TDdnxinAaSyCcWOEjf0B+cwTMXrcWb
yJ8P8lTqQN/aBeQviEV0SjXk2GptN6zMaeIge8TPBljFRhae1ECbSGPflPQNzASJ
qLL5ZV0fTc9ZwKdbAtfDh74dOGU1aRh6UK7ZooTR5HZmoHdyFh2lg/aKtGtVRYG1
5FAnTSZxgYkRviZhVLnJzpVRepy1Xa3llzt4J46Uyufy6hQUt9qECwR/udrO/52V
lfu9dzVe6bE=
=luks
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.12a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes in the 4.12 cycle.
Matt finally set up the lightning storm he needed to test the as3935.
* core
- Fix a null pointer deference in iio_trigger_write_current when changing
from a non existent trigger to another non existent trigger.
* a3935
- Recalibrate the RCO after resume.
- Fix interrupt mask so that we actually get some interrupts.
- Use iio_trigger_poll_chained as we aren't in interrupt context.
* am335x
- Fix wrong allocation size provided for private data to iio_device_alloc.
* bcm_iproc
- Swapped primary and secondary isr handlers.
* ltr501
- Fix swapped als/ps register fields when enabling interrupts
* max9611
- Wrong scale factor for the shunt_resistor attribute.
* sun4-gpadc
- Module autoloading fixes by adding the device table declarations.
- Fix parent device being used in devm functions.
For the sake of DT binding stability, this IIO driver is a child of an
MFD driver for Allwinner A10, A13 and A31 because there already exists a
DT binding for this IP. The MFD driver has a DT node but the IIO driver
does not.
The IIO device registers the temperature sensor in the thermal framework
using the DT node of the parent, the MFD device, so the thermal
framework could match the phandle to the MFD device in the DT and the
struct device used to register in the thermal framework.
devm_thermal_zone_of_sensor_register was previously used to register the
thermal sensor with the parent struct device of the IIO device,
representing the MFD device. By doing so, we registered actually the
parent in the devm routine and not the actual IIO device.
This lead to the devm unregister function not being called when the IIO
module driver is removed. It resulted in the thermal framework still
polling the get_temp function of the IIO module while the device doesn't
exist anymore, thus generated a kernel panic.
Use the non-devm function instead and do the unregister manually in the
remove function.
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This is an upstream port of an IIO driver for the TI ADC108S102 and
ADC128S102. The former can be found on the Intel Galileo Gen2 and the
Siemens SIMATIC IOT2000. For those boards, ACPI-based enumeration is
included.
Due to the lack of regulators under ACPI, we hard-code the voltage
provided to the VA pin of the ADC to 5 V, the value used on Galileo and
IOT2000. For DT usage, the regulator "vref-supply" provides this
information. Note that DT usage has not been tested.
Original author: Bogdan Pricop <bogdan.pricop@emutex.com>
Ported from Intel Galileo Gen2 BSP to Intel Yocto kernel:
Todor Minchev <todor@minchev.co.uk>.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The third argument of devm_request_threaded_irq() is the primary
handler. It is called in hardirq context and checks whether the
interrupt is relevant to the device. If the primary handler returns
IRQ_WAKE_THREAD, the secondary handler (a.k.a. handler thread) is
scheduled to run in process context.
bcm_iproc_adc.c uses the secondary handler as the primary one
and the other way around. So this patch fixes the same, along with
re-naming the secondary handler and primary handler names properly.
Tested on the BCM9583XX iProc SoC based boards.
Fixes: 4324c97ece ("iio: Add driver for Broadcom iproc-static-adc")
Reported-by: Pavel Roskin <plroskin@gmail.com>
Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@broadcom.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Reset GPIO is active low.
Currently driver uses gpiod_set_value(1) to clean reset, which depends
on device tree to contain GPIO_ACTIVE_HIGH - that does not match reality.
This fixes driver to use _raw version of gpiod_set_value() to enforce
active-low semantics despite of what's written in device tree. Allowing
device tree to override that only opens possibility for errors and does
not add any value.
Additionally, use _cansleep version to make things work with i2c-gpio
and other sleeping gpio drivers.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Possible values of sensing_mode are encoded with strings and actual
strings used are not obvious.
Provide a hint by enabling in_voltage_sensing_mode_available attribute.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Currently, driver generates events for channels if new reading differs
from previous one. This "previous value" is initialized to zero, which
results into event if value is constant-one.
Fix that by initializing "previous value" by reading at event enable
time.
This provides reliable sequence for userspace:
- enable event,
- AFTER THAT read current value,
- AFTER THAT each event will correspond to change.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With current event-only driver, it is not possible for user space
application to know current senses if they don't change since
application starts.
Address that by adding raw access to channels.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The power and current "shunt-resistor" attribute's 'show' function
displays the resistor value in milli-Ohms, while the ABI description
specifies it should be displayed in Ohms. Fix it.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the Texas Instruments ADC084S021 ADC chip.
Signed-off-by: Mårten Lindahl <martenli@axis.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
We should be allocating enough information for a tiadc_device struct
which is about 400 bytes but instead we allocate enough for a second
iio_dev struct which is over 2000 bytes.
Fixes: fea89e2dfc ("iio: adc: ti_am335x_adc: use variable names for sizeof() operator")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
-----BEGIN PGP SIGNATURE-----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=lbS7
-----END PGP SIGNATURE-----
Merge tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull hw lockdown support from David Howells:
"Annotation of module parameters that configure hardware resources
including ioports, iomem addresses, irq lines and dma channels.
This allows a future patch to prohibit the use of such module
parameters to prevent that hardware from being abused to gain access
to the running kernel image as part of locking the kernel down under
UEFI secure boot conditions.
Annotations are made by changing:
module_param(n, t, p)
module_param_named(n, v, t, p)
module_param_array(n, t, m, p)
to:
module_param_hw(n, t, hwtype, p)
module_param_hw_named(n, v, t, hwtype, p)
module_param_hw_array(n, t, hwtype, m, p)
where the module parameter refers to a hardware setting
hwtype specifies the type of the resource being configured. This can
be one of:
ioport Module parameter configures an I/O port
iomem Module parameter configures an I/O mem address
ioport_or_iomem Module parameter could be either (runtime set)
irq Module parameter configures an I/O port
dma Module parameter configures a DMA channel
dma_addr Module parameter configures a DMA buffer address
other Module parameter configures some other value
Note that the hwtype is compile checked, but not currently stored (the
lockdown code probably won't require it). It is, however, there for
future use.
A bonus is that the hwtype can also be used for grepping.
The intention is for the kernel to ignore or reject attempts to set
annotated module parameters if lockdown is enabled. This applies to
options passed on the boot command line, passed to insmod/modprobe or
direct twiddling in /sys/module/ parameter files.
The module initialisation then needs to handle the parameter not being
set, by (1) giving an error, (2) probing for a value or (3) using a
reasonable default.
What I can't do is just reject a module out of hand because it may
take a hardware setting in the module parameters. Some important
modules, some ipmi stuff for instance, both probe for hardware and
allow hardware to be manually specified; if the driver is aborts with
any error, you don't get any ipmi hardware.
Further, trying to do this entirely in the module initialisation code
doesn't protect against sysfs twiddling.
[!] Note that in and of itself, this series of patches should have no
effect on the the size of the kernel or code execution - that is
left to a patch in the next series to effect. It does mark
annotated kernel parameters with a KERNEL_PARAM_FL_HWPARAM flag in
an already existing field"
* tag 'hwparam-20170420' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs: (38 commits)
Annotate hardware config module parameters in sound/pci/
Annotate hardware config module parameters in sound/oss/
Annotate hardware config module parameters in sound/isa/
Annotate hardware config module parameters in sound/drivers/
Annotate hardware config module parameters in fs/pstore/
Annotate hardware config module parameters in drivers/watchdog/
Annotate hardware config module parameters in drivers/video/
Annotate hardware config module parameters in drivers/tty/
Annotate hardware config module parameters in drivers/staging/vme/
Annotate hardware config module parameters in drivers/staging/speakup/
Annotate hardware config module parameters in drivers/staging/media/
Annotate hardware config module parameters in drivers/scsi/
Annotate hardware config module parameters in drivers/pcmcia/
Annotate hardware config module parameters in drivers/pci/hotplug/
Annotate hardware config module parameters in drivers/parport/
Annotate hardware config module parameters in drivers/net/wireless/
Annotate hardware config module parameters in drivers/net/wan/
Annotate hardware config module parameters in drivers/net/irda/
Annotate hardware config module parameters in drivers/net/hamradio/
Annotate hardware config module parameters in drivers/net/ethernet/
...
If the driver is built as a module, it won't be autloaded if the devices
are registered via OF code because the OF device table
entries are not exported as aliases
Before the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
After the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: of:N*T*Callwinner,sun8i-a33-thsC*
alias: of:N*T*Callwinner,sun8i-a33-ths
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
Signed-off-by: Eduardo Molinas <edu.molinas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
If the driver is built as a module, it won't be autloaded if the devices
are registered via PLATFORM code because the PLATFORM device table
entries are not exported as aliases
Before the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
$
After the patch:
$ modinfo drivers/iio/adc/sun4i-gpadc-iio.ko | grep alias
alias: platform:sun6i-a31-gpadc-iio
alias: platform:sun5i-a13-gpadc-iio
alias: platform:sun4i-a10-gpadc-iio
Signed-off-by: Eduardo Molinas <edu.molinas@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Commit 7906dd52c5 ("iio: ina2xx: Fix whitespace and re-order code")
changed the register number of the MASK_ENABLE register from 0x06 to the
value equivalent GENMASK(2,1), although its no mask.
Also fix a typo (INA2_6_6 instead of INA2_2_6), and use the datasheet
name ("Mask/Enable") for the register number define.
Fix bad indentation for channel attributes.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Meson GX SoCs however use some magic bits to prevent simultaneous (=
conflicting, because only consumer should use the FIFO buffer with the
ADC results) usage by the Linux kernel and the bootloader (the BL30
bootloader uses the SAR ADC to read the CPU temperature).
This patch changes guards all BL30 functionality so it is skipped on
SoCs which don't have it. Since the hardware itself doesn't know whether
BL30 is available the internal meson_sar_adc_data is extended so this
information can be provided per of_device_id.data inside the driver.
Additionally the clocks "adc_clk" and "adc_sel" are not provided by the
clock-controller itself. "adc_sel" is not available at all. "adc_clk"
is provided by the SAR ADC IP block itself on Meson8b (and earlier).
This is already supported by the meson_saradc driver.
Finally this introduces new of_device_ids for the Meson8 and Meson8b
SoCs so the driver can be wired up in the corresponding DT.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These are only passed as of_device_id.data and never modified. Thus we
can mark them as static const, just like the of_device_id instances
where they are used.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Here is the big staging tree update for 4.12-rc1. And it's a big one,
adding about 350k new lines of crap^Wcode, mostly all in a big dump of
media drivers from Intel. But there's other new drivers in here as
well, yet-another-wifi driver, new IIO drivers, and a new crypto
accelerator. We also deleted a bunch of stuff, mostly in patch
cleanups, but also the Android ION code has shrunk a lot, and the
Android low memory killer driver was finally deleted, much to the
celebration of the -mm developers.
All of these have been in linux-next with a few build issues that will
show up when you merge to your tree, I'll follow up with fixes for those
after this gets merged.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWQzzlQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylNMgCcD+GoaF/Ml7YnULRl2GG/526II78AnitZ8qjd
rPqeowMIewYu9fgckLUc
=7rzO
-----END PGP SIGNATURE-----
Merge tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO updates from Greg KH:
"Here is the big staging tree update for 4.12-rc1.
It's a big one, adding about 350k new lines of crap^Wcode, mostly all
in a big dump of media drivers from Intel. But there's other new
drivers in here as well, yet-another-wifi driver, new IIO drivers, and
a new crypto accelerator.
We also deleted a bunch of stuff, mostly in patch cleanups, but also
the Android ION code has shrunk a lot, and the Android low memory
killer driver was finally deleted, much to the celebration of the -mm
developers.
All of these have been in linux-next with a few build issues that will
show up when you merge to your tree"
Merge conflicts in the new rtl8723bs driver (due to the wifi changes
this merge window) handled as per linux-next, courtesy of Stephen
Rothwell.
* tag 'staging-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (1182 commits)
staging: fsl-mc/dpio: add cpu <--> LE conversion for dpaa2_fd
staging: ks7010: remove line continuations in quoted strings
staging: vt6656: use tabs instead of spaces
staging: android: ion: Fix unnecessary initialization of static variable
staging: media: atomisp: fix range checking on clk_num
staging: media: atomisp: fix misspelled word in comment
staging: media: atomisp: kmap() can't fail
staging: atomisp: remove #ifdef for runtime PM functions
staging: atomisp: satm include directory is gone
atomisp: remove some more unused files
atomisp: remove hmm_load/store/clear indirections
atomisp: kill off mmgr_free
atomisp: clean up the hmm init/cleanup indirections
atomisp: handle allocation calls before init in the hmm layer
staging: fsl-dpaa2/eth: Add maintainer for Ethernet driver
staging: fsl-dpaa2/eth: Add TODO file
staging: fsl-dpaa2/eth: Add trace points
staging: fsl-dpaa2/eth: Add driver specific stats
staging: fsl-dpaa2/eth: Add ethtool support
staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver
...
The X-Powers AXP20X and AXP22X PMICs have multiple ADCs. They expose the
battery voltage, battery charge and discharge currents, AC-in and VBUS
voltages and currents, 2 GPIOs muxable in ADC mode and PMIC temperature.
This adds support for most of AXP20X and AXP22X ADCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The "if" interface clock speed is actually derived from the "fck"
block clock, as in the hardware they are the same clock. Drop the
incorrect second "if" clock and get the clock speed from "fck".
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-renesas-soc@vger.kernel.org
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When the kernel is running in secure boot mode, we lock down the kernel to
prevent userspace from modifying the running kernel image. Whilst this
includes prohibiting access to things like /dev/mem, it must also prevent
access by means of configuring driver modules in such a way as to cause a
device to access or modify the kernel image.
To this end, annotate module_param* statements that refer to hardware
configuration and indicate for future reference what type of parameter they
specify. The parameter parser in the core sees this information and can
skip such parameters with an error message if the kernel is locked down.
The module initialisation then runs as normal, but just sees whatever the
default values for those parameters is.
Note that we do still need to do the module initialisation because some
drivers have viable defaults set in case parameters aren't specified and
some drivers support automatic configuration (e.g. PNP or PCI) in addition
to manually coded parameters.
This patch annotates drivers in drivers/iio/.
Suggested-by: Alan Cox <gnomes@lxorguk.ukuu.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
cc: linux-iio@vger.kernel.org
This adds max1117/max1118/max1119 8-bit, dual-channel ADC driver.
This new driver uses the zero length spi_transfers with the cs_change
flag set and/or the non-zero delay_usecs.
1. The zero length transfer with the spi_transfer.cs_change set is
required in order to select CH1. The chip select line must be brought
high and low again without transfer.
2. The zero length transfer with the spi_transfer.delay_usecs > 0 is
required for waiting the conversion to be complete. The conversion
begins with the falling edge of the chip select. During the conversion
process, SCLK is ignored.
These two usages are unusual. But the spi controller drivers that use
a default implementation of transfer_one_message() are likely to work.
(I've tested this adc driver with spi-omap2-mcspi and spi-xilinx)
On the other hand, some spi controller drivers that have their own
transfer_one_message() may not work. But at least for the zero length
transfer with delay_usecs > 0, I'm proposing a new testcase for the
spi-loopback-test that can test whether the delay_usecs setting has
taken effect.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Mark Brown <broonie@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The Qualcomm PM8xxx PMICs contain a simpler ADC than its
successors (already in the kernel as qcom-spmi-vadc.c):
the HK/XO ADC (Housekeeping/Chrystal oscillator ADC).
As far as I can understand this is equal to the PMICs
using SSBI transport and encompass PM8018, PM8038,
PM8058, and PM8921, so this is shortly named PM8xxx.
This ADC monitors a bunch of on-board voltages and the die
temperature of the PMIC itself, but it can also be routed
to convert a few external MPPs (multi-purpose pins). On
the APQ8060 DragonBoard this feature is used to let this
ADC convert an analog ALS (Ambient Light Sensor) voltage
signal from a Capella CM3605 ALS into a LUX value.
Developed and tested with APQ8060 DragonBoard based on
Ivan's driver and Rama Krishna's patches. The SPMI VADC
driver is quite different, but share enough minor
functionality that I have split out to the common file
in a previous patch.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The SPMI VADC and the earlier XOADC share a subset of
common code, so to be able to use the same code in both
drivers, we break out a separate file with the common code,
prefix exported functions that are no longer static with
qcom_* and bake an object qcom-spmi-vadc.o that contains both
files: qcom-vadc-common.o and qcom-spmi-vadc-core.o.
As we need to follow the procedure for making a kernel module
or compiled in object from several files, but still want to
produce the same module name, rename the qcom-spmi-vadc.c
file to qcom-spmi-vadc-core.c so we can bake the two objects
into qcom-spmi-vadc.o
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Rama Krishna Phani A <rphani@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the Allwinner A33 thermal sensor.
Unlike the A10, A13 and A31, the Allwinner A33 only has one channel
which is dedicated to the thermal sensor. Moreover, its thermal sensor
does not generate interruptions, thus we only need to directly read the
register storing the temperature value.
The MFD used by the A10, A13 and A31, was created to avoid breaking the
DT binding, but since the nodes for the ADC weren't there for the A33,
it is not needed.
Though the A33 does not have an internal ADC, it has a thermal sensor
which shares the same registers with GPADC of the already supported SoCs
and almost the same bits, for the same purpose (thermal sensor).
The thermal sensor behaves exactly the same (except the presence of
interrupts or not) on the different SoCs.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This moves code used in MFD probing to a new sun4i_gpadc_probe_mfd
function.
This driver was initially written for A10, A13 and A31 SoCs which
already had a DT binding for this IP, thus we needed to use an MFD to
probe the different drivers without changing the DT binding of these
SoCs.
For SoCs that will require to create a DT binding for this IP, we can
avoid using an MFD, thus we need two separate functions: one for probing
via MFD and one for probing without MFD.
This split the code specific to MFD probing in a function separated from
the driver probe function.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
stm32 adc supports several resolution. Add 'assigned-resolution-bits'
dt optional property to set it. Default to maximum resolution in case
it isn't set.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
-----BEGIN PGP SIGNATURE-----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=YYdq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.12c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Third set of new device support, cleanups and features for IIO in the 4.12 cycle
Somewhat dominated in patch numbers of last of the outreachy application
window related patches (they are still coming, despite window being closed
which is good to see!)
Good set of new drivers as well.
New device support
* ASPEED ADC
- new driver
* cpcap PMIC ADC
- new driver
* hid-humidity
- driver for HID compatible humidity sensors.
* ltc2497 ADC
- new driver
* mpu6050
- bring bindings up to date and add trivial support for 9250
* rockchip-saradc
- update bindings to cover rk3328
* vl6180 light, proximity and time of flight sensor.
- new driver
Features
* meson-saradc
- add calibration
Cleanup and minor fixes
* ad5504
- constify attribute_group structure
- drop casting of void *
* ad7150
- replace some shifts of 1 by BIT macro usage
* ad7152
- blank lines between function definitions
* ad7280a
- octal permissions.
* ad7606
- replace use of core mlock mutex with a local lock
* ad7746
- replace some shifts of 1 by BIT macro usage
- function parameter alignment
- drop some excessive brackets (introduced in last pull request)
* ad7753
- white space cleanup
* ad7754
- includes in alphabetical order and groupped appropriately.
- change from missuse of internal mlock mutex to using the buffer lock to
also protect values during frequency update.
* ad779x
- constify attribute_group structures
* ad9832
- octal permissions
* adis16060
- remove use of core mlock mutex in favour of adding a local
_spi_write_then_read which can use the local buffer protection lock.
- fix naming of above function.
* adis16203
- remove locking during reads of calibbias that doesn't protect anything
not protected elsewhere.
* adis16209
- remove unnecessary braces in single statement if
* adis16240
- remove unnecessary braces in single statement if
* adt7136
- drop excess blank lines and put some in between functions.
* ams-iaq
- replace comma with semi colon. Not actual bug, just unusual syntax.
* apds9960
- constify attribute group structure
* as3935
- constify attribute group structure
* bm1750
- constify attribute group structure
* cros_ec
- devm version of triggered buffer setup to simplify code.
* exynos
- drop casting of void *
* hdc100x
- constify attribute_group structure
* hid-accel
- fix wrong scale for newly introduced gravity sensor.
* hts221
- drop casting of void *
* hx711
- constify attribute_group structure
* imx7d_adc
- drop casting of void *
* lm35333
- constify attribute_group structure
* lsm6dsx
- drop casting of void *
- hold ODR configuration until enabling to avoid a race condition.
* max1027
- drop casting of void *
* max11100
- fix a comma where semicolon was intended (no actual bug, just odd)
* max1363
- constify attribute_group structure
* ms sensors
- drop casting of void *
* rockchip_saradc
- drop casting of void *
* sun4i-gpadc
- fix missing dependency on THERMAL or presence of stubs (issue only
introduced in pervious set)
- drop casting of void *
* tsl2x7x
- fix wrong standard deviation calc. Note these aren't actually used for
anything at the moment so bug didn't really matter.
- constify attribute group structure.
* vf610adc
- drop casting of void *
* vz89x
- replace comma with semicolon. Not actual bug, just odd syntax.
* zpa2326
- drop casting of void *
With CONFIG_THERMAL=m and CONFIG_SUN4I_GPADC=y, we get a link error
from calling devm_thermal_zone_of_sensor_register:
drivers/iio/built-in.o: In function `sun4i_gpadc_probe':
:(.text+0x1c284): undefined reference to `devm_thermal_zone_of_sensor_register'
This adds a Kconfig dependency to ensure we can only have the ADC
driver as built-in when this function is also built-in, or when
we see the empty stub implementation. When the thermal code is
a module, we can still build the adc driver as a module, too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: d1caa99055 ("iio: adc: add support for Allwinner SoCs ADC")
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for the Analog Devices / Linear Technology
LTC2497 ADCs. The LTC2497 is a 16-channel (eight differential),
16-bit, high precision, delta-sigma ADC with an automatic, differential,
input current cancellation front end and a 2-wire, I2C interface.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The following Coccinelle script was used to detect this:
@r@
expression x;
void* e;
type T;
identifier f;
@@
(
*((T *)e)
|
((T *)x)[...]
|
((T*)x)->f
|
- (T*)
e
)
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Aspeed BMC SoCs include a 16 channel, 10-bit ADC. Low and high threshold
interrupts are supported by the hardware but are not currently implemented.
Signed-off-by: Rick Altherr <raltherr@google.com>
Tested-by: Xo Wang <xow@google.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
3042 480 0 3522 dc2 drivers/iio/adc/hx711.o
File size after:
text data bss dec hex filename
3098 416 0 3514 dba drivers/iio/adc/hx711.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
On Motorola phones like droid 4 there is a custom CPCAP PMIC. This PMIC
has ADCs that are used for battery charging and USB PHY VBUS and ID pin
detection.
Unfortunately the only documentation for this ADC seems to be the
Motorola mapphone Linux kernel tree. I have tested that reading raw and
scaled values works, but I have not used the timed sampling that the ADC
seems to support.
Let's add a minimal support for it so we can eventually provide IIO
channels for the related battery charging and USB PHY drivers.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Replace a comma between expression statements by a semicolon. This
changes the semantics of the code, but given the current indentation
appears to be what is intended.
A simplified version of the Coccinelle semantic patch that performs this
transformation is as follows:
// <smpl>
@r@
expression e1,e2;
@@
e1
-,
+;
e2;
// </smpl>
Signed-off-by: Arushi Singhal <arushisinghal19971997@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
26051 464 0 26515 6793 drivers/iio/adc/ad799x.o
File size after:
text data bss dec hex filename
26115 400 0 26515 6793 drivers/iio/adc/ad799x.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
36951 448 0 37399 9217 drivers/iio/adc/max1363.o
File size after:
text data bss dec hex filename
37015 384 0 37399 9217 drivers/iio/adc/max1363.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds calibration for the Meson SAR ADC.
Points 25% vref and 75% vref are used for calibration.
It uses a simple linear calibration function: SCALE * val + BIAS
Successfully tested on a Odroid C2.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Since the driver has been split into MFD there is no reason for it to
stay, so remove it.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for sixteen-channel 12-bit resolution ADC and its functions,
which include general-purpose ADC readings, battery voltage measurement,
and die temperature measurement.
Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic@gmail.com>
Reviewed-by: Jonathan Cameron <jic23@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
PC/104 drivers should be hidden on machines which do not support PC/104
devices. This patch adds the PC104 Kconfig option as a dependency for
the relevant PC/104 device driver Kconfig options.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The tiadc_irq_h(int irq, void *private) function is handling FIFO
overruns by clearing flags, disabling and enabling the ADC to
recover.
If the ADC is running in continuous mode a FIFO overrun happens
regularly. If the disabling of the ADC happens concurrently with
a new conversion. It might happen that the enabling of the ADC
is ignored by the hardware. This stops the ADC permanently. No
more interrupts are triggered.
According to the AM335x Reference Manual (SPRUH73H October 2011 -
Revised April 2013 - Chapter 12.4 and 12.5) it is necessary to
check the ADC FSM bits in REG_ADCFSM before enabling the ADC
again. Because the disabling of the ADC is done right after the
current conversion has been finished.
To trigger this bug it is necessary to run the ADC in continuous
mode. The ADC values of all channels need to be read in an endless
loop. The bug appears within the first 6 hours (~5.4 million
handled FIFO overruns). The user space application will hang on
reading new values from the character device.
Fixes: ca9a563805 ("iio: ti_am335x_adc: Add continuous sampling
support")
Signed-off-by: Michael Engl <michael.engl@wjw-solutions.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Fabrice Gasnier