- Set up mvebu BAR 0 so MSI works even if bootloader doesn't do this
(Shmuel Hazan)
* remotes/lorenzo/pci/mvebu:
PCI: mvebu: Setup BAR0 in order to fix MSI
- Fix loongson class code quirk so it happens early enough (Tiezhu Yang)
* remotes/lorenzo/pci/loongson:
PCI: loongson: Use DECLARE_PCI_FIXUP_EARLY for bridge_class_quirk()
- Fix hv timing issue that causes kdump failures (Wei Hu)
- Make some hv functions static (Wei Yongjun)
* remotes/lorenzo/pci/hv:
PCI: hv: Make some functions static
PCI: hv: Fix a timing issue which causes kdump to fail occasionally
- Convert cadence to use standard "dma-ranges" DT property instead of its
own "cdns,no-bar-match-nbits" (Kishon Vijay Abraham I)
- Fix pm_runtime_put_sync() issues in cadence error paths (Kishon Vijay
Abraham I)
- Add PTR_ALIGN_DOWN macro (Kishon Vijay Abraham I)
- Convert cadence r/w accessors to only 32-bit accesses (Kishon Vijay
Abraham I)
- Add cadence support to start Link and check Link status (Kishon Vijay
Abraham I)
- Allow custom PCI ops for cadence-based drivers (Kishon Vijay Abraham I)
- Remove "mem" from cadence reg binding since it's not memory and it
overlaps the PCIe config and memory region (Kishon Vijay Abraham I)
- Add cadence ->cpu_addr_fixup() for platforms that require absolute
addresses in the ATU, not just offsets (Kishon Vijay Abraham I)
- Update cadence Vendor IDs using local management registers, not
architected config space (Kishon Vijay Abraham I)
- Add cadence endpoint driver MSI-X support (Kishon Vijay Abraham I)
- Add bindings and driver for TI J721E SoC, supporting both host and
endpoint mode (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/cadence:
MAINTAINERS: Add Kishon Vijay Abraham I for TI J721E SoC PCIe
misc: pci_endpoint_test: Add J721E in pci_device_id table
PCI: j721e: Add TI J721E PCIe driver
dt-bindings: PCI: Add EP mode dt-bindings for TI's J721E SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J721E SoC
PCI: cadence: Add MSI-X support to Endpoint driver
PCI: cadence: Fix updating Vendor ID and Subsystem Vendor ID register
PCI: cadence: Add new *ops* for CPU addr fixup
dt-bindings: PCI: cadence: Remove "mem" from reg binding
PCI: cadence: Allow pci_host_bridge to have custom pci_ops
PCI: cadence: Add support to start link and verify link status
PCI: cadence: Convert all r/w accessors to perform only 32-bit accesses
linux/kernel.h: Add PTR_ALIGN_DOWN macro
PCI: cadence: Fix cdns_pcie_{host|ep}_setup() error path
PCI: cadence: Use "dma-ranges" instead of "cdns,no-bar-match-nbits" property
- Use pci_channel_state_t instead of enum pci_channel_state (Luc Van
Oostenryck)
- Simplify __aer_print_error() (Bjorn Helgaas)
- Log AER correctable errors as warning, not error (Matt Jolly)
- Rename pci_aer_clear_device_status() to pcie_clear_device_status() (Bjorn
Helgaas)
- Clear PCIe Device Status errors only if OS owns AER (Jonathan Cameron)
* pci/error:
PCI/ERR: Clear PCIe Device Status errors only if OS owns AER
PCI/ERR: Rename pci_aer_clear_device_status() to pcie_clear_device_status()
PCI/AER: Log correctable errors as warning, not error
PCI/AER: Simplify __aer_print_error()
PCI: Use 'pci_channel_state_t' instead of 'enum pci_channel_state'
Add support for Versal CPM as Root Port.
The Versal ACAP devices include CCIX-PCIe Module (CPM). The integrated
block for CPM along with the integrated bridge can function as PCIe Root
Port.
Bridge error and legacy interrupts in Versal CPM are handled using Versal
CPM specific interrupt line.
[bhelgaas: fold in kerneldoc fix from
https://lore.kernel.org/linux-acpi/20200729201224.26799-7-krzk@kernel.org/]
Link: https://lore.kernel.org/r/1592312214-9347-3-git-send-email-bharat.kumar.gogada@xilinx.com
Signed-off-by: Bharat Kumar Gogada <bharat.kumar.gogada@xilinx.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The majority of DT based host drivers use the default .map_irq() and
.swizzle_irq() functions, so let's initialize the function pointers to
the default and drop setting them in the host drivers.
Drivers like iProc which don't support legacy interrupts need to set
.map_irq() back to NULL.
Link: https://lore.kernel.org/r/20200722022514.1283916-20-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Now that pci_parse_request_of_pci_ranges() callers just setup
pci_host_bridge.windows and dma_ranges directly and don't need the bus
range returned, we can just initialize them when allocating the
pci_host_bridge struct.
With this, pci_parse_request_of_pci_ranges() becomes a static function.
Link: https://lore.kernel.org/r/20200722022514.1283916-19-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The rcar-gen2 host driver still uses the old Arm PCI setup function
pci_common_init_dev(). Let's update it to use the modern
devm_pci_alloc_host_bridge(), pci_parse_request_of_pci_ranges() and
pci_host_probe() functions.
Link: https://lore.kernel.org/r/20200722022514.1283916-18-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-renesas-soc@vger.kernel.org
- Eliminate significant AML processing overhead related to using
operation regions in system memory by reworking the management
of memory mappings in the ACPI code to defer unmap operations
(to do them outside of the ACPICA locks, among other things) and
making the memory operation reagion handler avoid releasing memory
mappings created by it too early (Rafael Wysocki).
- Update the ACPICA code in the kernel to upstream revision
20200717:
* Prevent operation region reference counts from overflowing in
some cases (Erik Kaneda).
* Replace one-element array with flexible-array (Gustavo A. R.
Silva).
- Fix ACPI PCI hotplug reference counting (Rafael Wysocki).
- Drop last bits of the ACPI procfs interface (Thomas Renninger).
- Drop some redundant checks from the code parsing ACPI tables
related to NUMA (Hanjun Guo).
- Avoid redundant object evaluation in the ACPI device properties
handling code (Heikki Krogerus).
- Avoid unecessary memory overhead related to storing the signatures
of the ACPI tables recognized by the kernel (Ard Biesheuvel).
- Add missing newline characters when printing module parameter
values in some places (Xiongfeng Wang).
- Update the link to the ACPI specifications in some places (Tiezhu
Yang).
- Use the fallthrough pseudo-keyword in the ACPI code (Gustavo A. R.
Silva).
- Drop redundant variable initialization from the APEI code (Colin
Ian King).
- Drop uninitialized_var() from the ACPI PAD driver (Jason Yan).
- Replace HTTP links with HTTPS ones in the ACPI code (Alexander A.
Klimov).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl8oO8gSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRx2nUP/iSRAW0DK4PYDNLDV1Q+y5RrQw44iMDf
yfLQu3agardM1KGtPuYw5zmU0UoEYtW8s2r027bxw9Hvn0IzBh5TiDvcVjMEnbVC
+6m/fWg3EStfZ9w2dxDzXDMIk/oiEZsjtWSRaDTfAIH2jc/xVcSXDojlMgBPQDu5
hIITjMbGGx783o4PNCYbIZy1ReJgd8MNQ+Xp3MCpTgbFgHMHKBOJ6B/nS8aTfilO
eE5JvzhXED7qITaXYWxI9OZpRTPTNQ3eaEPbWvnw4KJ5boMfyREMGdTBipXO+kSA
SwKhFysYEUAZM7Ffq0eTnWSCU7VWogAsTauIgs4+d9z8VrGhWi5+b6N/E/uwTKtj
HF98xtk+Loe8V24LwN0snvv51O7P5nAH47QxwIBvQssfR8ZSgdwHtUQcckybAJhx
LLmPtJrM8ZAefc9H4o0eVqumjoh1amGKC9dTY0g1j0UIE0y3ZIFHTvDNvhpTzgBk
5uUHHEiolGNWHVrs1LIMOEejqx62m+EjVc9b8XUdJqHoboTccMM73DRk/00meP/7
br/VfMI0aTjPLssvSC/ZSlTZt+ddrBm+cXw9eqruDQwdQaqxpJu+D3odjdaYSjpg
luiYQrQdoDmIDh4UNuJbvG/Hub3CLzvJSqGWLExNbX7nWXxH4HIx/8PcNtVkKZRV
qBXotIc+i4VD
=Nn2Q
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These eliminate significant AML processing overhead related to using
operation regions in system memory, update the ACPICA code in the
kernel to upstream revision 20200717 (including a fix to prevent
operation region reference counts from overflowing in some cases),
remove the last bits of the (long deprecated) ACPI procfs interface
and do some assorted cleanups.
Specifics:
- Eliminate significant AML processing overhead related to using
operation regions in system memory by reworking the management of
memory mappings in the ACPI code to defer unmap operations (to do
them outside of the ACPICA locks, among other things) and making
the memory operation reagion handler avoid releasing memory
mappings created by it too early (Rafael Wysocki).
- Update the ACPICA code in the kernel to upstream revision 20200717:
* Prevent operation region reference counts from overflowing in
some cases (Erik Kaneda).
* Replace one-element array with flexible-array (Gustavo A. R.
Silva).
- Fix ACPI PCI hotplug reference counting (Rafael Wysocki).
- Drop last bits of the ACPI procfs interface (Thomas Renninger).
- Drop some redundant checks from the code parsing ACPI tables
related to NUMA (Hanjun Guo).
- Avoid redundant object evaluation in the ACPI device properties
handling code (Heikki Krogerus).
- Avoid unecessary memory overhead related to storing the signatures
of the ACPI tables recognized by the kernel (Ard Biesheuvel).
- Add missing newline characters when printing module parameter
values in some places (Xiongfeng Wang).
- Update the link to the ACPI specifications in some places (Tiezhu
Yang).
- Use the fallthrough pseudo-keyword in the ACPI code (Gustavo A. R.
Silva).
- Drop redundant variable initialization from the APEI code (Colin
Ian King).
- Drop uninitialized_var() from the ACPI PAD driver (Jason Yan).
- Replace HTTP links with HTTPS ones in the ACPI code (Alexander A.
Klimov)"
* tag 'acpi-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (22 commits)
ACPI: APEI: remove redundant assignment to variable rc
ACPI: NUMA: Remove the useless 'node >= MAX_NUMNODES' check
ACPI: NUMA: Remove the useless sub table pointer check
ACPI: tables: Remove the duplicated checks for acpi_parse_entries_array()
ACPICA: Update version to 20200717
ACPICA: Do not increment operation_region reference counts for field units
ACPICA: Replace one-element array with flexible-array
ACPI: Replace HTTP links with HTTPS ones
ACPI: Use valid link to the ACPI specification
ACPI: OSL: Clean up the removal of unused memory mappings
ACPI: OSL: Use deferred unmapping in acpi_os_unmap_iomem()
ACPI: OSL: Use deferred unmapping in acpi_os_unmap_generic_address()
ACPICA: Preserve memory opregion mappings
ACPI: OSL: Implement deferred unmapping of ACPI memory
ACPI: Use fallthrough pseudo-keyword
PCI: hotplug: ACPI: Fix context refcounting in acpiphp_grab_context()
ACPI: tables: avoid relocations for table signature array
ACPI: PAD: Eliminate usage of uninitialized_var() macro
ACPI: sysfs: add newlines when printing module parameters
ACPI: EC: add newline when printing 'ec_event_clearing' module parameter
...
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the values
become larger. This is now replaced with more precise arithmetics,
using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=PbO7
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the
values become larger. This is now replaced with more precise
arithmetics, using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
* tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/doc: Factorize bits between sched-energy.rst & sched-capacity.rst
sched/doc: Document capacity aware scheduling
sched: Document arch_scale_*_capacity()
arm, arm64: Fix selection of CONFIG_SCHED_THERMAL_PRESSURE
Documentation/sysctl: Document uclamp sysctl knobs
sched/uclamp: Add a new sysctl to control RT default boost value
sched/uclamp: Fix a deadlock when enabling uclamp static key
sched: Remove duplicated tick_nohz_full_enabled() check
sched: Fix a typo in a comment
sched/uclamp: Remove unnecessary mutex_init()
arm, arm64: Select CONFIG_SCHED_THERMAL_PRESSURE
sched: Cleanup SCHED_THERMAL_PRESSURE kconfig entry
arch_topology, sched/core: Cleanup thermal pressure definition
trace/events/sched.h: fix duplicated word
linux/sched/mm.h: drop duplicated words in comments
smp: Fix a potential usage of stale nr_cpus
sched/fair: update_pick_idlest() Select group with lowest group_util when idle_cpus are equal
sched: nohz: stop passing around unused "ticks" parameter.
sched: Better document ttwu()
sched: Add a tracepoint to track rq->nr_running
...
that helps the debugging of IRQ affinity logic bugs, and fix a memory leak.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=oKU9
-----END PGP SIGNATURE-----
Merge tag 'irq-urgent-2020-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Ingo Molnar:
"Fix a recent IRQ affinities regression, add in a missing debugfs
printout that helps the debugging of IRQ affinity logic bugs, and fix
a memory leak"
* tag 'irq-urgent-2020-08-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq/debugfs: Add missing irqchip flags
genirq/affinity: Make affinity setting if activated opt-in
irqdomain/treewide: Free firmware node after domain removal
- Removal of the tremendously unpopular read_barrier_depends() barrier,
which is a NOP on all architectures apart from Alpha, in favour of
allowing architectures to override READ_ONCE() and do whatever dance
they need to do to ensure address dependencies provide LOAD ->
LOAD/STORE ordering. This work also offers a potential solution if
compilers are shown to convert LOAD -> LOAD address dependencies into
control dependencies (e.g. under LTO), as weakly ordered architectures
will effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic, augment
the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the device
ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions and
kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words.
-----BEGIN PGP SIGNATURE-----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=mh79
-----END PGP SIGNATURE-----
Merge tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 and cross-arch updates from Catalin Marinas:
"Here's a slightly wider-spread set of updates for 5.9.
Going outside the usual arch/arm64/ area is the removal of
read_barrier_depends() series from Will and the MSI/IOMMU ID
translation series from Lorenzo.
The notable arm64 updates include ARMv8.4 TLBI range operations and
translation level hint, time namespace support, and perf.
Summary:
- Removal of the tremendously unpopular read_barrier_depends()
barrier, which is a NOP on all architectures apart from Alpha, in
favour of allowing architectures to override READ_ONCE() and do
whatever dance they need to do to ensure address dependencies
provide LOAD -> LOAD/STORE ordering.
This work also offers a potential solution if compilers are shown
to convert LOAD -> LOAD address dependencies into control
dependencies (e.g. under LTO), as weakly ordered architectures will
effectively be able to upgrade READ_ONCE() to smp_load_acquire().
The latter case is not used yet, but will be discussed further at
LPC.
- Make the MSI/IOMMU input/output ID translation PCI agnostic,
augment the MSI/IOMMU ACPI/OF ID mapping APIs to accept an input ID
bus-specific parameter and apply the resulting changes to the
device ID space provided by the Freescale FSL bus.
- arm64 support for TLBI range operations and translation table level
hints (part of the ARMv8.4 architecture version).
- Time namespace support for arm64.
- Export the virtual and physical address sizes in vmcoreinfo for
makedumpfile and crash utilities.
- CPU feature handling cleanups and checks for programmer errors
(overlapping bit-fields).
- ACPI updates for arm64: disallow AML accesses to EFI code regions
and kernel memory.
- perf updates for arm64.
- Miscellaneous fixes and cleanups, most notably PLT counting
optimisation for module loading, recordmcount fix to ignore
relocations other than R_AARCH64_CALL26, CMA areas reserved for
gigantic pages on 16K and 64K configurations.
- Trivial typos, duplicate words"
Link: http://lkml.kernel.org/r/20200710165203.31284-1-will@kernel.org
Link: http://lkml.kernel.org/r/20200619082013.13661-1-lorenzo.pieralisi@arm.com
* tag 'arm64-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (82 commits)
arm64: use IRQ_STACK_SIZE instead of THREAD_SIZE for irq stack
arm64/mm: save memory access in check_and_switch_context() fast switch path
arm64: sigcontext.h: delete duplicated word
arm64: ptrace.h: delete duplicated word
arm64: pgtable-hwdef.h: delete duplicated words
bus: fsl-mc: Add ACPI support for fsl-mc
bus/fsl-mc: Refactor the MSI domain creation in the DPRC driver
of/irq: Make of_msi_map_rid() PCI bus agnostic
of/irq: make of_msi_map_get_device_domain() bus agnostic
dt-bindings: arm: fsl: Add msi-map device-tree binding for fsl-mc bus
of/device: Add input id to of_dma_configure()
of/iommu: Make of_map_rid() PCI agnostic
ACPI/IORT: Add an input ID to acpi_dma_configure()
ACPI/IORT: Remove useless PCI bus walk
ACPI/IORT: Make iort_msi_map_rid() PCI agnostic
ACPI/IORT: Make iort_get_device_domain IRQ domain agnostic
ACPI/IORT: Make iort_match_node_callback walk the ACPI namespace for NC
arm64: enable time namespace support
arm64/vdso: Restrict splitting VVAR VMA
arm64/vdso: Handle faults on timens page
...
Add support for PCIe controller in J721E SoC. The controller uses the
Cadence PCIe core programmed by pcie-cadence*.c. The PCIe controller
will work in both host mode and device mode.
Some of the features of the controller are:
*) Supports both RC mode and EP mode
*) Supports MSI and MSI-X support
*) Supports upto GEN3 speed mode
*) Supports SR-IOV capability
*) Ability to route all transactions via SMMU (support will be added
in a later patch).
Link: https://lore.kernel.org/r/20200722110317.4744-14-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix a missing __iomem tag in the init_pfn() function. This fixes a sparse
warning of the form:
$ make C=2 drivers/pci/switch/
drivers/pci/switch/switchtec.c:... incorrect type assignment(different address spaces)
Fixes: 080b47def5 ("MicroSemi Switchtec management interface driver")
Link: https://lore.kernel.org/r/20200728192434.18993-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Fix a number of missing __iomem and __user tags in the ioctl functions of
the switchtec driver. This fixes a number of sparse warnings of the form:
$ make C=2 drivers/pci/switch/
drivers/pci/switch/switchtec.c:... incorrect type in ... (different address spaces)
Fixes: 52eabba5bc ("switchtec: Add IOCTLs to the Switchtec driver")
Link: https://lore.kernel.org/r/20200728192434.18993-1-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The sparse tool report build warnings as follows:
drivers/pci/hotplug/rpadlpar_core.c:355:5: warning: symbol 'dlpar_remove_pci_slot' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:461:12: warning: symbol 'rpadlpar_io_init' was not declared. Should it be static?
drivers/pci/hotplug/rpadlpar_core.c:473:6: warning: symbol 'rpadlpar_io_exit' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Also mark rpadlpar_io_exit() as __exit.
Link: https://lore.kernel.org/r/20200721151735.41181-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Allow P2PDMA if the CPU vendor is AMD and family is 0x17 (Zen) or greater.
[bhelgaas: commit log, simplify #if/#else/#endif]
Link: https://lore.kernel.org/r/20200729231844.4653-1-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Huang Rui <ray.huang@amd.com>
Recently ASPM handling was changed to allow ASPM on PCIe-to-PCI/PCI-X
bridges. Unfortunately the ASMedia ASM1083/1085 PCIe to PCI bridge device
doesn't seem to function properly with ASPM enabled. On an Asus PRIME
H270-PRO motherboard, it causes errors like these:
pcieport 0000:00:1c.0: AER: PCIe Bus Error: severity=Corrected, type=Data Link Layer, (Transmitter ID)
pcieport 0000:00:1c.0: AER: device [8086:a292] error status/mask=00003000/00002000
pcieport 0000:00:1c.0: AER: [12] Timeout
pcieport 0000:00:1c.0: AER: Corrected error received: 0000:00:1c.0
pcieport 0000:00:1c.0: AER: can't find device of ID00e0
In addition to flooding the kernel log, this also causes the machine to
wake up immediately after suspend is initiated.
The device advertises ASPM L0s and L1 support in the Link Capabilities
register, but the ASMedia web page for ASM1083 [1] claims "No PCIe ASPM
support".
Windows 10 (build 2004) enables L0s, but it also logs correctable PCIe
errors.
Add a quirk to disable ASPM for this device.
[1] https://www.asmedia.com.tw/eng/e_show_products.php?cate_index=169&item=114
[bhelgaas: commit log]
Fixes: 66ff14e59e ("PCI/ASPM: Allow ASPM on links to PCIe-to-PCI/PCI-X Bridges")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208667
Link: https://lore.kernel.org/r/20200722021803.17958-1-hancockrwd@gmail.com
Signed-off-by: Robert Hancock <hancockrwd@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The acpi_get_table() should be coupled with acpi_put_table() if the mapped
table is not used at runtime to release the table mapping.
In pci_quirk_amd_sb_acs(), IVRS table is just used for checking AMD IOMMU
is supported, not used at runtime, so put the table after using it.
Fixes: 15b100dfd1 ("PCI: Claim ACS support for AMD southbridge devices")
Link: https://lore.kernel.org/r/1595411068-15440-1-git-send-email-guohanjun@huawei.com
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Announce the device, e.g.,
pci 0000:00:00.0: [8086:5910] type 00 class 0x060000
after running early fixups, so the log message reflects any device type or
class code fixups.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/1595833615-8049-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We are seeing AMD Radeon Pro W5700 doesn't work when IOMMU is enabled:
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01a0]
iommu ivhd0: AMD-Vi: Event logged [IOTLB_INV_TIMEOUT device=63:00.0 address=0x42b5b01c0]
The error also makes graphics driver fail to probe the device.
It appears to be the same issue as commit 5e89cd303e ("PCI: Mark AMD
Navi14 GPU rev 0xc5 ATS as broken") addresses, and indeed the same ATS
quirk can workaround the issue.
See-also: 5e89cd303e ("PCI: Mark AMD Navi14 GPU rev 0xc5 ATS as broken")
See-also: d28ca864c4 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
See-also: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=208725
Link: https://lore.kernel.org/r/20200728104554.28927-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
388c8c16ab ("PCI: add routines for debugging and handling lost
interrupts") added pci_lost_interrupt() that apparently never has had a
single user. Remove it.
Link: https://lore.kernel.org/r/e328d059-3068-6a40-28df-f81f616d15a0@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
There is nothing PCI bus specific in the of_msi_map_rid()
implementation other than the requester ID tag for the input
ID space. Rename requester ID to a more generic ID so that
the translation code can be used by all busses that require
input/output ID translations.
No functional change intended.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200619082013.13661-11-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
of_msi_map_get_device_domain() is PCI specific but it need not be and
can be easily changed to be bus agnostic in order to be used by other
busses by adding an IRQ domain bus token as an input parameter.
Signed-off-by: Diana Craciun <diana.craciun@oss.nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci/msi.c
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200619082013.13661-10-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
There is nothing PCI specific in iort_msi_map_rid().
Rename the function using a bus protocol agnostic name,
iort_msi_map_id(), and convert current callers to it.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-4-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
iort_get_device_domain() is PCI specific but it need not be,
since it can be used to retrieve IRQ domain nexus of any kind
by adding an irq_domain_bus_token input to it.
Make it PCI agnostic by also renaming the requestor ID input
to a more generic ID name.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # pci/msi.c
Cc: Will Deacon <will@kernel.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Link: https://lore.kernel.org/r/20200619082013.13661-3-lorenzo.pieralisi@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Implement ->set_msix() and ->get_msix() callback functions in order
to configure MSIX capability in the PCIe endpoint controller.
Add cdns_pcie_ep_send_msix_irq() to send MSIX interrupts to Host.
cdns_pcie_ep_send_msix_irq() gets the MSIX table address (virtual
address) from "struct cdns_pcie_epf" that gets initialized in
->set_bar() call back function.
[kishon@ti.com: Re-implement MSIX support in accordance with the
re-designed core MSI-X interfaces]
Link: https://lore.kernel.org/r/20200722110317.4744-11-kishon@ti.com
Signed-off-by: Alan Douglas <adouglas@cadence.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
sparse report build warning as follows:
drivers/pci/controller/pci-hyperv.c:941:5: warning:
symbol 'hv_read_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1021:5: warning:
symbol 'hv_write_config_block' was not declared. Should it be static?
drivers/pci/controller/pci-hyperv.c:1090:5: warning:
symbol 'hv_register_block_invalidate' was not declared. Should it be static?
Those functions are not used outside of this file, so mark them static.
Link: https://lore.kernel.org/r/20200706135234.80758-1-weiyongjun1@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Tegra PCI controller driver doesn't need to control the PLL power
supplies directly, but rather uses the pads provided by the XUSB pad
controller, which in turn is responsible for supplying power to the
PLLs.
Link: https://lore.kernel.org/r/20200623145528.1658337-2-thierry.reding@gmail.com
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The HiSilicon non-ECAM PCIe has been broken since March 2016 commit
7e57fd1444 ("PCI: designware: Move Root Complex setup code to
dw_pcie_setup_rc()"). The reason is this commit moved the iATU setup code
from dw_pcie_host_init() to dw_pcie_setup_rc(), but the hisi driver never
calls dw_pcie_setup_rc(). The result is the PCI memory space is never
configured and the driver can't work. It's also clear it has an iATU as
the config space accesses use it.
There's also no dts file using either "hisilicon,hip05-pcie" or
"hisilicon,hip06-pcie".
Link: https://lore.kernel.org/r/20200724224204.3249055-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Commit 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe
controller") in order to update Vendor ID, directly wrote to
PCI_VENDOR_ID register. However PCI_VENDOR_ID in root port configuration
space is read-only register and writing to it will have no effect.
Use local management register to configure Vendor ID and Subsystem Vendor
ID.
Link: https://lore.kernel.org/r/20200722110317.4744-10-kishon@ti.com
Fixes: 1b79c52844 ("PCI: cadence: Add host driver for Cadence PCIe controller")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence driver uses "mem" memory resource to obtain the offset of
configuration space address region, memory space address region and
message space address region. The obtained offset is used to program
the Address Translation Unit (ATU). However certain platforms like TI's
J721E SoC require the absolute address to be programmed in the ATU and
not just the offset. Add new *ops* for CPU addr fixup for the platform
drivers to provide the correct address to be programmed in the ATU.
Link: https://lore.kernel.org/r/20200722110317.4744-9-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Certain platforms like TI's J721E allows only 32-bit configuration
space access. In such cases pci_generic_config_read and
pci_generic_config_write cannot be used. Add support in Cadence core
to let pci_host_bridge have custom pci_ops.
Link: https://lore.kernel.org/r/20200722110317.4744-7-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add cdns_pcie_ops to start link and verify link status. The registers
to start link and to check link status is in Platform specific PCIe
wrapper. Add support for platform specific drivers to add callback
functions for the PCIe Cadence core to start link and verify link status.
Link: https://lore.kernel.org/r/20200722110317.4744-6-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Certain platforms like TI's J721E using Cadence PCIe IP can perform only
32-bit accesses for reading or writing to Cadence registers. Convert all
read and write accesses to 32-bit in Cadence PCIe driver in preparation
for adding PCIe support in TI's J721E SoC.
Also add spin lock to disable interrupts while modifying PCI_STATUS
register while raising legacy interrupt since PCI_STATUS is accessible
by both remote RC and EP and time between read and write should be
minimized.
Link: https://lore.kernel.org/r/20200722110317.4744-5-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit bd22885aa1 ("PCI: cadence: Refactor driver to use as a core
library") while refactoring the Cadence PCIe driver to be used as
library, removed pm_runtime_get_sync() from cdns_pcie_ep_setup()
and cdns_pcie_host_setup() but missed to remove the corresponding
pm_runtime_put_sync() in the error path. Fix it here.
Link: https://lore.kernel.org/r/20200722110317.4744-3-kishon@ti.com
Fixes: bd22885aa1 ("PCI: cadence: Refactor driver to use as a core library")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cadence PCIe core driver (host mode) uses "cdns,no-bar-match-nbits"
property to configure the number of bits passed through from PCIe
address to internal address in Inbound Address Translation register.
This only used the NO MATCH BAR.
However standard PCI dt-binding already defines "dma-ranges" to
describe the address ranges accessible by PCIe controller. Add support
in Cadence PCIe host driver to parse dma-ranges and configure the
inbound regions for BAR0, BAR1 and NO MATCH BAR. Cadence IP specifies
maximum size for BAR0 as 256GB, maximum size for BAR1 as 2 GB.
This adds support to take the next biggest region in "dma-ranges" and
find the smallest BAR that each of the regions fit in and if there is
no BAR big enough to hold the region, split the region to see if it can
be fitted using multiple BARs.
"dma-ranges" of J721E will be
dma-ranges = <0x02000000 0x0 0x0 0x0 0x0 0x10000 0x0>;
Since there is no BAR which can hold 2^48 size, NO_MATCH_BAR will be
used here.
Legacy device tree binding compatibility is maintained by retaining
support for "cdns,no-bar-match-nbits".
Link: https://lore.kernel.org/r/20200722110317.4744-2-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Kdump could fail sometime on Hyper-V guest because the retry in
hv_pci_enter_d0() releases child device structures in hv_pci_bus_exit().
Although there is a second asynchronous device relations message sending
from the host, if this message arrives to the guest after
hv_send_resource_allocated() is called, the retry would fail.
Fix the problem by moving retry to hv_pci_probe() and start the retry
from hv_pci_query_relations() call. This will cause a device relations
message to arrive to the guest synchronously; the guest would then be
able to rebuild the child device structures before calling
hv_send_resource_allocated().
Link: https://lore.kernel.org/r/20200727071731.18516-1-weh@microsoft.com
Fixes: c81992e7f4 ("PCI: hv: Retry PCI bus D0 entry on invalid device state")
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: fixed a comment and commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
-----BEGIN PGP SIGNATURE-----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=hzUW
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci into master
Pull PCI fixes from Bjorn Helgaas:
- Reject invalid IRQ 0 command line argument for virtio_mmio because
IRQ 0 now generates warnings (Bjorn Helgaas)
- Revert "PCI/PM: Assume ports without DLL Link Active train links in
100 ms", which broke nouveau (Bjorn Helgaas)
* tag 'pci-v5.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI/PM: Assume ports without DLL Link Active train links in 100 ms"
virtio-mmio: Reject invalid IRQ 0 command line argument
For SR-IOV, the PF PRI is shared between the PF and any associated VFs, and
the PRI Capability is allowed for PFs but not for VFs. Searching for the
PRI Capability on a VF always fails, even if its associated PF supports
PRI.
Add pci_pri_supported() to check whether device or its associated PF
supports PRI.
[bhelgaas: commit log, avoid "!!"]
Fixes: b16d0cb9e2 ("iommu/vt-d: Always enable PASID/PRI PCI capabilities before ATS")
Link: https://lore.kernel.org/r/1595543849-19692-1-git-send-email-ashok.raj@intel.com
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Acked-by: Joerg Roedel <jroedel@suse.de>
Cc: stable@vger.kernel.org # v4.4+
The pci-rcar-gen2 controller requires only a prefetchable memory region,
and the error prevents using pci_parse_request_of_pci_ranges() for it.
Let's reduce this to just a warning message so this function can be used
for pci-rcar-gen2.
Link: https://lore.kernel.org/r/20200722022514.1283916-17-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200722022514.1283916-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
There's no need to store the bus number or range resource as the driver
only needs the bus number which is already in the pci_host_bridge.
For endpoint mode, the bus number is always 0.
Link: https://lore.kernel.org/r/20200722022514.1283916-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Instead of parsing 'ranges' from DT again, use the bridge window
resources.
Link: https://lore.kernel.org/r/20200722022514.1283916-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Tom Joseph <tjoseph@cadence.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Most host drivers only parse the DT bus range to set the root bus number
in pci_host_bridge.busnr. The ones that don't set busnr are buggy in
that they ignore what's in DT. Let's set busnr in pci_scan_root_bus_bridge()
where we already check for the bus resource and remove setting it in
host drivers.
Link: https://lore.kernel.org/r/20200722022514.1283916-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Will Deacon <will@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-tegra@vger.kernel.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: linux-renesas-soc@vger.kernel.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Also, bridge->busnr is never set so effectively the root bus must be 0.
This will be fixed by a subsequent commit.
Link: https://lore.kernel.org/r/20200722022514.1283916-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
There was also a bug that the root_busno is never set which means the
root bus number is always 0 even if the DT said something else.
Link: https://lore.kernel.org/r/20200722022514.1283916-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
There was also a bug that the pci_host_bridge.busnr is set from
root_busno, but root_busno is never set which means the root bus number
is always 0 even if the DT said something else.
Link: https://lore.kernel.org/r/20200722022514.1283916-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Use pci_is_root_bus() rather than tracking the root bus number to
determine if the bus is the root bus or not. This removes storing
duplicated data as well as the need for the host bridge driver to have
to care about the bus numbers in most cases.
Link: https://lore.kernel.org/r/20200722022514.1283916-5-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The struct pci_host_bridge is 0 initialized when allocated, so there's
no need to explicitly set fields to 0.
Link: https://lore.kernel.org/r/20200722022514.1283916-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
The host bridge's parent device is always the platform device. As we
already have a pointer to it in the devres functions, let's initialize
the parent device. Drivers can still override the parent if desired.
Link: https://lore.kernel.org/r/20200722022514.1283916-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
PCI_ENABLE_PROC_DOMAINS is only used on powerpc and doesn't do anything
for the Versatile host driver, so let's drop it. I'm not sure how or why
I had this to begin with. PCI_ENABLE_PROC_DOMAINS was never used on ARM.
Link: https://lore.kernel.org/r/20200722022514.1283916-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
devm_pci_remap_cfg_resource() will print an error message by itself when
goes wrong, so remove the duplicate error message.
Link: https://lore.kernel.org/r/20200526150954.4729-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
pm_runtime_get_sync() increments the runtime PM usage counter even
when the call returns an error code. Thus a corresponding decrement is
needed on the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200709064356.8800-1-dinghao.liu@zju.edu.cn
Fixes: 0df6150e7c ("PCI: rcar: Use runtime PM to control controller clock")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Commit 711419e504 ("irqdomain: Add the missing assignment of
domain->fwnode for named fwnode") unintentionally caused a dangling pointer
page fault issue on firmware nodes that were freed after IRQ domain
allocation. Commit e3beca48a4 fixed that dangling pointer issue by only
freeing the firmware node after an IRQ domain allocation failure. That fix
no longer frees the firmware node immediately, but leaves the firmware node
allocated after the domain is removed.
The firmware node must be kept around through irq_domain_remove, but should be
freed it afterwards.
Add the missing free operations after domain removal where where appropriate.
Fixes: e3beca48a4 ("irqdomain/treewide: Keep firmware node unconditionally allocated")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # drivers/pci
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/1595363169-7157-1-git-send-email-jonathan.derrick@intel.com
pcie_clear_device_status() resets the error bits in the PCIe Device Status
Register (PCI_EXP_DEVSTA).
Previously we did this unconditionally, but on ACPI systems, the _OSC AER
bit negotiates control of the AER capability. Per sec 4.5.1 of the System
Firmware Intermediary _OSC and DPC Updates ECN [1], this bit also covers
other error enable/status bits including the following:
Correctable Error Reporting Enable
Non-Fatal Error Reporting Enable
Fatal Error Reporting Enable
Unsupported Request Reporting Enable
These bits are all in the PCIe Device Control register (the ECN omitted
"Reporting", but I think that's a typo), so by implication the _OSC AER bit
also applies to the error status bits in the PCIe Device Status register:
Correctable Error Detected
Non-Fatal Error Detected
Fatal Error Detected
Unsupported Request Detected
Clear the PCIe Device Status error bits only when the OS controls the AER
capability and related error enable/status bits. If platform firmware
controls the AER capability, firmware is responsible for clearing these
bits.
One call path leading here is:
ghes_do_proc
ghes_handle_aer
aer_recover_queue
schedule_work(&aer_recover_work)
...
aer_recover_work_func
pcie_do_recovery
pcie_clear_device_status
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[bhelgaas: commit log, move test from pcie_clear_device_status() to callers]
Link: https://lore.kernel.org/r/20200622113523.891666-1-Jonathan.Cameron@huawei.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_aer_clear_device_status() clears the error bits in the PCIe Device
Status Register (PCI_EXP_DEVSTA). Every PCIe device has this register,
regardless of whether it supports AER.
Rename pci_aer_clear_device_status() to pcie_clear_device_status() to make
clear that it is PCIe-specific but not AER-specific. Move it to
drivers/pci/pci.c, again since it's not AER-specific. No functional change
intended.
Link: https://lore.kernel.org/r/20200717195619.766662-1-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When there is no PCIe card connected and advk_pcie_rd_conf() or
advk_pcie_wr_conf() is called for PCI bus which doesn't belong to emulated
root bridge, the aardvark driver throws the following error message:
advk-pcie d0070000.pcie: config read/write timed out
Obviously accessing PCIe registers of disconnected card is not possible.
Extend check in advk_pcie_valid_device() function for validating
availability of PCIe bus. If PCIe link is down, then the device is marked
as Not Found and the driver does not try to access these registers.
This is just an optimization to prevent accessing PCIe registers when card
is disconnected. Trying to access PCIe registers of disconnected card does
not cause any crash, kernel just needs to wait for a timeout. So if card
disappear immediately after checking for PCIe link (before accessing PCIe
registers), it does not cause any problems.
Link: https://lore.kernel.org/r/20200702083036.12230-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the datasheet of Loongson LS7A bridge chip, the old version
of Loongson LS7A PCIE port has a wrong value about PCI class which is
0x060000, the correct value should be 0x060400, this bug can be fixed by
"dev->class = PCI_CLASS_BRIDGE_PCI << 8;" at the software level and it
was fixed in hardware in the latest LS7A versions.
In order to maintain downward compatibility, use DECLARE_PCI_FIXUP_EARLY
instead of DECLARE_PCI_FIXUP_HEADER for bridge_class_quirk() to fix it as
early as possible.
Otherwise, in the function pci_setup_device(), the related code about
"dev->class" such as "class = dev->class >> 8;" and "dev->transparent
= ((dev->class & 0xff) == 1);" maybe get wrong value without EARLY fixup.
Link: https://lore.kernel.org/r/1595065176-460-1-git-send-email-yangtiezhu@loongson.cn
Fixes: 1f58cca5cf ("PCI: Add Loongson PCI Controller support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
As reported in https://bugzilla.kernel.org/206217 , raw_violation_fixup
is causing more harm than good in some common use-cases.
This patch is a partial revert of commit:
191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
and fixes the following regression since then.
* Description:
When both the NIC and MMC are used one can see the following message:
NETDEV WATCHDOG: enp1s0 (r8169): transmit queue 0 timed out
and
pcieport 0000:00:02.0: AER: Uncorrected (Non-Fatal) error received: 0000:01:00.0
r8169 0000:01:00.0: AER: PCIe Bus Error: severity=Uncorrected (Non-Fatal), type=Transaction Layer, (Requester ID)
r8169 0000:01:00.0: AER: device [10ec:8168] error status/mask=00004000/00400000
r8169 0000:01:00.0: AER: [14] CmpltTO (First)
r8169 0000:01:00.0: AER: can't recover (no error_detected callback)
pcieport 0000:00:02.0: AER: device recovery failed
After that, the ethernet NIC is not functional anymore even after
reloading the r8169 module. After a reboot, this is reproducible by
copying a large file over the NIC to the MMC.
For some reason this is not reproducible when files are copied to a tmpfs.
* Little background on the fixup, by Manikanta Maddireddy:
"In the internal testing with dGPU on Tegra124, CmplTO is reported by
dGPU. This happened because FIFO queue in AFI(AXI to PCIe) module
get full by upstream posted writes. Back to back upstream writes
interleaved with infrequent reads, triggers RAW violation and CmpltTO.
This is fixed by reducing the posted write credits and by changing
updateFC timer frequency. These settings are fixed after stress test.
In the current case, RTL NIC is also reporting CmplTO. These settings
seems to be aggravating the issue instead of fixing it."
Link: https://lore.kernel.org/r/20200718100710.15398-1-kwizart@gmail.com
Fixes: 191cd6fb5d ("PCI: tegra: Add SW fixup for RAW violations")
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Cc: stable@vger.kernel.org
When I cat ASPM parameter 'policy' by sysfs, it displays as follows. Add a
newline for easy reading. Other sysfs attributes already include a
newline.
[root@localhost ~]# cat /sys/module/pcie_aspm/parameters/policy
[default] performance powersave powersupersave [root@localhost ~]#
Fixes: 7d715a6c1a ("PCI: add PCI Express ASPM support")
Link: https://lore.kernel.org/r/1594972765-10404-1-git-send-email-wangxiongfeng2@huawei.com
Signed-off-by: Xiongfeng Wang <wangxiongfeng2@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use devm_platform_ioremap_resource_byname() to simplify the code
since it contains platform_get_resource_byname() and
devm_ioremap_resource() respectively.
Link: https://lore.kernel.org/r/20200708164013.5076-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Using uninitialized_var() is dangerous as it papers over real bugs[1]
(or can in the future), and suppresses unrelated compiler warnings
(e.g. "unused variable"). If the compiler thinks it is uninitialized,
either simply initialize the variable or make compiler changes.
In preparation for removing[2] the[3] macro[4], remove all remaining
needless uses with the following script:
git grep '\buninitialized_var\b' | cut -d: -f1 | sort -u | \
xargs perl -pi -e \
's/\buninitialized_var\(([^\)]+)\)/\1/g;
s:\s*/\* (GCC be quiet|to make compiler happy) \*/$::g;'
drivers/video/fbdev/riva/riva_hw.c was manually tweaked to avoid
pathological white-space.
No outstanding warnings were found building allmodconfig with GCC 9.3.0
for x86_64, i386, arm64, arm, powerpc, powerpc64le, s390x, mips, sparc64,
alpha, and m68k.
[1] https://lore.kernel.org/lkml/20200603174714.192027-1-glider@google.com/
[2] https://lore.kernel.org/lkml/CA+55aFw+Vbj0i=1TGqCR5vQkCzWJ0QxK6CernOU6eedsudAixw@mail.gmail.com/
[3] https://lore.kernel.org/lkml/CA+55aFwgbgqhbp1fkxvRKEpzyR5J8n1vKT1VZdz9knmPuXhOeg@mail.gmail.com/
[4] https://lore.kernel.org/lkml/CA+55aFz2500WfbKXAx8s67wrm9=yVJu65TpLgN_ybYNv0VEOKA@mail.gmail.com/
Reviewed-by: Leon Romanovsky <leonro@mellanox.com> # drivers/infiniband and mlx4/mlx5
Acked-by: Jason Gunthorpe <jgg@mellanox.com> # IB
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless drivers
Reviewed-by: Chao Yu <yuchao0@huawei.com> # erofs
Signed-off-by: Kees Cook <keescook@chromium.org>
Quite some non OF/ACPI users of irqdomains allocate firmware nodes of type
IRQCHIP_FWNODE_NAMED or IRQCHIP_FWNODE_NAMED_ID and free them right after
creating the irqdomain. The only purpose of these FW nodes is to convey
name information. When this was introduced the core code did not store the
pointer to the node in the irqdomain. A recent change stored the firmware
node pointer in irqdomain for other reasons and missed to notice that the
usage sites which do the alloc_fwnode/create_domain/free_fwnode sequence
are broken by this. Storing a dangling pointer is dangerous itself, but in
case that the domain is destroyed later on this leads to a double free.
Remove the freeing of the firmware node after creating the irqdomain from
all affected call sites to cure this.
Fixes: 711419e504 ("irqdomain: Add the missing assignment of domain->fwnode for named fwnode")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/873661qakd.fsf@nanos.tec.linutronix.de
According to the Armada XP datasheet, section 10.2.6: "in order for
the device to do a write to the MSI doorbell address, it needs to write
to a register in the internal registers space".
As a result of the requirement above, without this patch, MSI won't
function and therefore some devices won't operate properly without
pci=nomsi.
This requirement was not present at the time of writing this driver
since the vendor u-boot always initializes all PCIe controllers
(incl. BAR0 initialization) and for some time, the vendor u-boot was
the only available bootloader for this driver's SoCs (e.g. A38x,A37x,
etc).
Tested on an Armada 385 board on mainline u-boot (2020.4), without
u-boot PCI initialization and the following PCIe devices:
- Wilocity Wil6200 rev 2 (wil6210)
- Qualcomm Atheros QCA6174 (ath10k_pci)
Both failed to get a response from the device after loading the
firmware and seem to operate properly with this patch.
Link: https://lore.kernel.org/r/20200623060334.108444-1-sh@tkos.co.il
Signed-off-by: Shmuel Hazan <sh@tkos.co.il>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
kobject_init_and_add() takes a reference even when it fails. If it returns
an error, kobject_put() must be called to clean up the memory associated
with the object.
When kobject_init_and_add() fails, call kobject_put() instead of kfree().
b8eb718348 ("net-sysfs: Fix reference count leak in
rx|netdev_queue_add_kobject") fixed a similar problem.
Link: https://lore.kernel.org/r/20200528021322.1984-1-wu000273@umn.edu
Signed-off-by: Qiushi Wu <wu000273@umn.edu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Currently the ACS capability is being looked up at a number of places. Read
and store it once at enumeration so that it can be used by all later. No
functional change intended.
Link: https://lore.kernel.org/r/20200707224604.3737893-2-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Move pci_enable_acs() and dependencies further up in the source code to
avoid having to forward declare it when we make it static in near future.
No functional changes intended.
Link: https://lore.kernel.org/r/20200707224604.3737893-1-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use devm_platform_ioremap_resource() to simplify the code, since t
contains platform_get_resource() and devm_ioremap_resource() calls
respectively.
Link: https://lore.kernel.org/r/20200708155614.308-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Use devm_platform_ioremap_resource_byname() to simplify the code,
since it calls respectively platform_get_resource_byname() and
devm_ioremap_resource().
Link: https://lore.kernel.org/r/20200602171601.17630-1-zhengdejin5@gmail.com
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The xilinx host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-16-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The xilinx-nwl host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-15-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Michal Simek <michal.simek@xilinx.com>
The rockchip host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-14-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: linux-rockchip@lists.infradead.org
The rcar host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-13-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: linux-renesas-soc@vger.kernel.org
The iproc host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-12-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
The altera host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
The only difference is pci_assign_unassigned_bus_resources() was called
instead of pci_bus_size_bridges() and pci_bus_assign_resources(). This
should be the same.
Link: https://lore.kernel.org/r/20200522234832.954484-11-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: rfi@lists.rocketboards.org
The xgene host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-10-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Toan Le <toan@os.amperecomputing.com>
The versatile host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-9-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The v3 host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-8-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
The tegra host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-7-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
The mobiveil host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-6-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
The brcmstb host driver does the same host registration and bus scanning
calls as pci_host_probe, so let's use it instead.
Link: https://lore.kernel.org/r/20200522234832.954484-5-robh@kernel.org
Tested-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-rpi-kernel@lists.infradead.org
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Will Deacon <will@kernel.org>
Use kzalloc() instead of kmalloc() in the panic message.
[bhelgaas: drop similar ibmphp_pci.c change since it's not obviously
correct]
Link: https://lore.kernel.org/r/1594279708-34369-1-git-send-email-wang.yi59@zte.com.cn
Signed-off-by: Liao Pingfang <liao.pingfang@zte.com.cn>
Signed-off-by: Yi Wang <wang.yi59@zte.com.cn>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pci_call_probe() prevents the nesting of work_on_cpu() for a scenario
where a VF device is probed from work_on_cpu() of the PF.
Replace the cpumask used in pci_call_probe() from all online CPUs to only
housekeeping CPUs. This is to ensure that there are no additional latency
overheads caused due to the pinning of jobs on isolated CPUs.
Signed-off-by: Alex Belits <abelits@marvell.com>
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Frederic Weisbecker <frederic@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lkml.kernel.org/r/20200625223443.2684-3-nitesh@redhat.com
PCIe correctable errors are recovered by hardware with no need for software
intervention (PCIe r5.0, sec 6.2.2.1).
Reduce the log level of correctable errors from KERN_ERR to KERN_WARNING.
The bug reports below are for correctable error logging. This doesn't fix
the cause of those reports, but it may make the messages less alarming.
[bhelgaas: commit log, use pci_printk() to avoid code duplication]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=201517
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196183
Link: https://lore.kernel.org/r/20200618155511.16009-1-Kangie@footclan.ninja
Signed-off-by: Matt Jolly <Kangie@footclan.ninja>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
aer_correctable_error_string[] and aer_uncorrectable_error_string[] have
descriptions of AER error status bits. Add NULL entries to these tables so
all entries for bits 0-31 are defined. Then we don't have to check for
ARRAY_SIZE() when decoding a status word, which simplifies
__aer_print_error().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
device_attach() returning failure indicates a driver error while trying to
probe the device. In such a scenario, the PCI device should still be added
in the system and be visible to the user.
When device_attach() fails, merely warn about it and keep the PCI device in
the system.
This partially reverts ab1a187bba ("PCI: Check device_attach() return
value always").
Link: https://lore.kernel.org/r/20200706233240.3245512-1-rajatja@google.com
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # v4.6+
The method struct pci_error_handlers.error_detected() is defined and
documented as taking an 'enum pci_channel_state' for the second argument,
but most drivers use 'pci_channel_state_t' instead.
This 'pci_channel_state_t' is not a typedef for the enum but a typedef for
a bitwise type in order to have better/stricter typechecking.
Consolidate everything by using 'pci_channel_state_t' in the method's
definition, in the related helpers and in the drivers.
Enforce use of 'pci_channel_state_t' by replacing 'enum pci_channel_state'
with an anonymous 'enum'.
Note: Currently, from a typechecking point of view this patch changes
nothing because only the constants defined by the enum are bitwise, not the
enum itself (sparse doesn't have the notion of 'bitwise enum'). This may
change in some not too far future, hence the patch.
[bhelgaas: squash in
https://lore.kernel.org/r/20200702162651.49526-3-luc.vanoostenryck@gmail.comhttps://lore.kernel.org/r/20200702162651.49526-4-luc.vanoostenryck@gmail.com]
Link: https://lore.kernel.org/r/20200702162651.49526-2-luc.vanoostenryck@gmail.com
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The pci_cfg_wait queue is used to prevent user-space config accesses to
devices while they are recovering from reset.
Previously we used these operations on pci_cfg_wait:
__add_wait_queue(&pci_cfg_wait, ...)
__remove_wait_queue(&pci_cfg_wait, ...)
wake_up_all(&pci_cfg_wait)
The wake_up acquires the wait queue lock, but the add and remove do not.
Originally these were all protected by the pci_lock, but cdcb33f982
("PCI: Avoid possible deadlock on pci_lock and p->pi_lock"), moved
wake_up_all() outside pci_lock, so it could race with add/remove
operations, which caused occasional kernel panics, e.g., during vfio-pci
hotplug/unplug testing:
Unable to handle kernel read from unreadable memory at virtual address ffff802dac469000
Resolve this by using wait_event() instead of __add_wait_queue() and
__remove_wait_queue(). The wait queue lock is held by both wait_event()
and wake_up_all(), so it provides mutual exclusion.
Fixes: cdcb33f982 ("PCI: Avoid possible deadlock on pci_lock and p->pi_lock")
Link: https://lore.kernel.org/linux-pci/79827f2f-9b43-4411-1376-b9063b67aee3@huawei.com/T/#u
Based-on: https://lore.kernel.org/linux-pci/20191210031527.40136-1-zhengxiang9@huawei.com/
Based-on-patch-by: Xiang Zheng <zhengxiang9@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Xiang Zheng <zhengxiang9@huawei.com>
Cc: Heyi Guo <guoheyi@huawei.com>
Cc: Biaoxiang Ye <yebiaoxiang@huawei.com>
Lots of define are actually already defined in pci_regs.h, directly use
the standard defines.
Link: https://lore.kernel.org/r/20200615210608.21469-13-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Some SoC based on ipq8064/5 needs to be limited to pci GEN1 speed due to
some hardware limitations. Add support for speed setting defined by the
max-link-speed binding. If not defined the max speed is set to GEN2 by
default.
Link: https://lore.kernel.org/r/20200615210608.21469-12-ansuelsmth@gmail.com
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Ipq8064-v2 have tx term offset set to 0. Introduce this variant to permit
different offset based on the revision.
Link: https://lore.kernel.org/r/20200615210608.21469-10-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add tx term offset support to pcie qcom driver need in some revision of
the ipq806x SoC. Ipq8064 needs tx term offset set to 7.
Link: https://lore.kernel.org/r/20200615210608.21469-9-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Set some specific value for Tx De-Emphasis, Tx Swing and Rx equalization
needed on some ipq8064 based device (Netgear R7800 for example). Without
this the system locks on kernel load.
Link: https://lore.kernel.org/r/20200615210608.21469-8-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v4.5+
Rework 2.1.0 revision to use bulk clk api and fix missing assert on
reset_control_deassert error.
Link: https://lore.kernel.org/r/20200615210608.21469-7-ansuelsmth@gmail.com
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The deinit issues reset_control_assert for PCI twice and does not contain
phy reset.
Link: https://lore.kernel.org/r/20200615210608.21469-4-ansuelsmth@gmail.com
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Aux and Ref clk are missing in PCIe qcom driver. Add support for this
optional clks for ipq8064/apq8064 SoC.
Link: https://lore.kernel.org/r/20200615210608.21469-2-ansuelsmth@gmail.com
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Sham Muthayyan <smuthayy@codeaurora.org>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Most callers of config read do not check for return value. But most of the
ones that do, checks for error indication in 'val' variable.
This patch updates error handling in advk_pcie_rd_conf() function. If PIO
transfer fails then 'val' variable is set to 0xffffffff which indicates
failture.
Link: https://lore.kernel.org/r/20200528162604.GA323482@bjorn-Precision-5520
Link: https://lore.kernel.org/r/20200601130315.18895-1-pali@kernel.org
Reported-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code, thus a matching decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200707055000.9453-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520090253.2761-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200520084756.31620-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
VMD device 28C0 natively assists guest passthrough of the VMD endpoint
through the use of shadow registers that provide Host Physical Addresses
to correctly assign bridge windows. These shadow registers are only
available if VMD config space register 0x70, bit 1 is set.
In order to support this mode in existing VMD devices which don't
natively support the shadow register, it was decided that the hypervisor
could offer the shadow registers in a vendor-specific PCI capability.
QEMU has been modified to create this vendor-specific capability and
supply the shadow membar registers for VMDs which don't natively support
this feature. This patch adds this mode and updates the supported device
list to allow this feature to be used on these VMDs.
Link: https://lore.kernel.org/r/20200528030240.16024-4-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Jason Cooper <jason@lakedaemon.net>
There's no need to create a temporary resource list and then splice it to
struct pci_host_bridge.windows list. Just use pci_host_bridge.windows
directly. The necessary clean-up is already handled by the PCI core.
Link: https://lore.kernel.org/r/20200522234832.954484-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Tom Joseph <tjoseph@cadence.com>
When debugging an issue where I was asking the PCI machinery to enable a
set of MSI-X vectors, without falling back on MSI, I ran across a behaviour
which seems odd. The pci_alloc_irq_vectors_affinity() will always return
-ENOSPC on failure, when allocating MSI-X vectors only, whereas with MSI
fallback it will forward any error returned by __pci_enable_msi_range().
This is a confusing behaviour, so have the pci_alloc_irq_vectors_affinity()
forward the error code from __pci_enable_msix_range() when appropriate.
Link: https://lore.kernel.org/r/20200616073318.20229-1-piotr.stankiewicz@intel.com
Signed-off-by: Piotr Stankiewicz <piotr.stankiewicz@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
The lkml.org, spinics.net, and gmane.org archives are not very reliable
and, in some cases, not even easily accessible. Replace links to them with
links to lore.kernel.org, the archives hosted by kernel.org.
I found the gmane items via the Wayback Machine archive at
https://web.archive.org/.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Replace http:// links with https:// links. This reduces the likelihood of
man-in-the-middle attacks when developers open these links.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
[bhelgaas: also update samsung.com links, drop sourceforge link]
Link: https://lore.kernel.org/r/20200627103050.71712-1-grandmaster@al2klimov.de
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI config accessors (pci_read_config_word(), et al) return
PCIBIOS_SUCCESSFUL (zero) or positive error values like
PCIBIOS_FUNC_NOT_SUPPORTED.
The PCIe capability accessors similarly return PCIBIOS errors, but in
addition, they can return -EINVAL. This makes it harder than it should be
to check for errors.
Return PCIBIOS_BAD_REGISTER_NUMBER instead of -EINVAL in all PCIe
capability accessors.
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Link: https://lore.kernel.org/r/20200615073225.24061-9-refactormyself@gmail.com
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The PCI config accessors (pci_read_config_word(), et al) return
PCIBIOS_SUCCESSFUL (zero) or positive error values like
PCIBIOS_FUNC_NOT_SUPPORTED.
The PCIe capability accessors (pcie_capability_read_word(), et al)
similarly return PCIBIOS errors, but some callers assume they return
generic errno values like -EINVAL.
For example, the Myri-10G probe function returns a positive PCIBIOS error
if the pcie_capability_clear_and_set_word() in pcie_set_readrq() fails:
myri10ge_probe
status = pcie_set_readrq
return pcie_capability_clear_and_set_word
if (status)
return status
A positive return from a PCI driver probe function would cause a "Driver
probe function unexpectedly returned" warning from local_pci_probe()
instead of the desired probe failure.
Convert PCIBIOS errors to generic errno for all callers of:
pcie_capability_read_word
pcie_capability_read_dword
pcie_capability_write_word
pcie_capability_write_dword
pcie_capability_set_word
pcie_capability_set_dword
pcie_capability_clear_word
pcie_capability_clear_dword
pcie_capability_clear_and_set_word
pcie_capability_clear_and_set_dword
that check the return code for anything other than zero.
[bhelgaas: commit log, squash together]
Suggested-by: Bjorn Helgaas <bjorn@helgaas.com>
Link: https://lore.kernel.org/r/20200615073225.24061-1-refactormyself@gmail.com
Signed-off-by: Bolarinwa Olayemi Saheed <refactormyself@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
If context is not NULL in acpiphp_grab_context(), but the
is_going_away flag is set for the device's parent, the reference
counter of the context needs to be decremented before returning
NULL or the context will never be freed, so make that happen.
Fixes: edf5bf34d4 ("ACPI / dock: Use callback pointers from devices' ACPI hotplug contexts")
Reported-by: Vasily Averin <vvs@virtuozzo.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
-----BEGIN PGP SIGNATURE-----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=1NIT
-----END PGP SIGNATURE-----
Merge tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull more Kbuild updates from Masahiro Yamada:
- fix build rules in binderfs sample
- fix build errors when Kbuild recurses to the top Makefile
- covert '---help---' in Kconfig to 'help'
* tag 'kbuild-v5.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
treewide: replace '---help---' in Kconfig files with 'help'
kbuild: fix broken builds because of GZIP,BZIP2,LZOP variables
samples: binderfs: really compile this sample and fix build issues
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQRTLbB6QfY48x44uB6AXGG7T9hjvgUCXuMTgwAKCRCAXGG7T9hj
vmX0AQCR8jeUkcc3+TDDuCugfH1AsyIRWavSEP/slqnEVuPhiwEA/324aID1v28U
CEsA7Iksf4nDGLEaC5I5Exshd15gQgY=
=W5nI
-----END PGP SIGNATURE-----
Merge tag 'for-linus-5.8b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
- several smaller cleanups
- a fix for a Xen guest regression with CPU offlining
- a small fix in the xen pvcalls backend driver
- an update of MAINTAINERS
* tag 'for-linus-5.8b-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
MAINTAINERS: Update PARAVIRT_OPS_INTERFACE and VMWARE_HYPERVISOR_INTERFACE
xen/pci: Get rid of verbose_request and use dev_dbg() instead
xenbus: Use dev_printk() when possible
xen-pciback: Use dev_printk() when possible
xen: enable BALLOON_MEMORY_HOTPLUG by default
xen: expand BALLOON_MEMORY_HOTPLUG description
xen/pvcalls: Make pvcalls_back_global static
xen/cpuhotplug: Fix initial CPU offlining for PV(H) guests
xen-platform: Constify dev_pm_ops
xen/pvcalls-back: test for errors when calling backend_connect()
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the
pdev->no_vf_scan flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio
and qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl7eVGcACgkQjYWKoQLX
FBhweQgAkicvx31x230rdfG+jQkQkl0UqF99vvWrJHEll77SqadfjzKAGIjUB+K0
EoeHVD5Wcj7BogDGcyHeQ0bZpu4WzE+y1nmnrsvu7TEEvcBmkJH0rF2jF+y0sb/O
3qvwFkX/CB5OqaMzKC/AEeRpcCKR+ZUXkWu1irbYth7CBXaycD9EAPc4cj8CfYGZ
r5njUdYOVk77TaO4aV+t5pCYc5TCRJaWXSsWaAv/nuLcIqsFBYOy2q+L47zITGXp
utZVanIDjzx+ikpaKicOIfC3hJsRuNX9MnlZKsQFwpVEZAUZmIUm29XdhGJTWSxU
RV7m1ORINbFP1nGAqWqkOvGo/LC0ZA==
=VhXR
-----END PGP SIGNATURE-----
Merge tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Add support for multi-function devices in pci code.
- Enable PF-VF linking for architectures using the pdev->no_vf_scan
flag (currently just s390).
- Add reipl from NVMe support.
- Get rid of critical section cleanup in entry.S.
- Refactor PNSO CHSC (perform network subchannel operation) in cio and
qeth.
- QDIO interrupts and error handling fixes and improvements, more
refactoring changes.
- Align ioremap() with generic code.
- Accept requests without the prefetch bit set in vfio-ccw.
- Enable path handling via two new regions in vfio-ccw.
- Other small fixes and improvements all over the code.
* tag 's390-5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (52 commits)
vfio-ccw: make vfio_ccw_regops variables declarations static
vfio-ccw: Add trace for CRW event
vfio-ccw: Wire up the CRW irq and CRW region
vfio-ccw: Introduce a new CRW region
vfio-ccw: Refactor IRQ handlers
vfio-ccw: Introduce a new schib region
vfio-ccw: Refactor the unregister of the async regions
vfio-ccw: Register a chp_event callback for vfio-ccw
vfio-ccw: Introduce new helper functions to free/destroy regions
vfio-ccw: document possible errors
vfio-ccw: Enable transparent CCW IPL from DASD
s390/pci: Log new handle in clp_disable_fh()
s390/cio, s390/qeth: cleanup PNSO CHSC
s390/qdio: remove q->first_to_kick
s390/qdio: fix up qdio_start_irq() kerneldoc
s390: remove critical section cleanup from entry.S
s390: add machine check SIGP
s390/pci: ioremap() align with generic code
s390/ap: introduce new ap function ap_get_qdev()
Documentation/s390: Update / remove developerWorks web links
...
Including:
- A big part of this is a change in how devices get connected to
IOMMUs in the core code. It contains the change from the old
add_device()/remove_device() to the new
probe_device()/release_device() call-backs. As a result
functionality that was previously in the IOMMU drivers has
been moved to the IOMMU core code, including IOMMU group
allocation for each device.
The reason for this change was to get more robust allocation
of default domains for the iommu groups.
A couple of fixes were necessary after this was merged into
the IOMMU tree, but there are no known bugs left. The last fix
is applied on-top of the merge commit for the topic branches.
- Removal of the driver private domain handling in the Intel
VT-d driver. This was fragile code and I am glad it is gone
now.
- More Intel VT-d updates from Lu Baolu:
- Nested Shared Virtual Addressing (SVA) support to the
Intel VT-d driver
- Replacement of the Intel SVM interfaces to the common
IOMMU SVA API
- SVA Page Request draining support
- ARM-SMMU Updates from Will:
- Avoid mapping reserved MMIO space on SMMUv3, so that
it can be claimed by the PMU driver
- Use xarray to manage ASIDs on SMMUv3
- Reword confusing shutdown message
- DT compatible string updates
- Allow implementations to override the default domain
type
- A new IOMMU driver for the Allwinner Sun50i platform
- Support for ATS gets disabled for untrusted devices (like
Thunderbolt devices). This includes a PCI patch, acked by
Bjorn.
- Some cleanups to the AMD IOMMU driver to make more use of
IOMMU core features.
- Unification of some printk formats in the Intel and AMD IOMMU
drivers and in the IOVA code.
- Updates for DT bindings
- A number of smaller fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=a4z4
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"A big part of this is a change in how devices get connected to IOMMUs
in the core code. It contains the change from the old add_device() /
remove_device() to the new probe_device() / release_device()
call-backs.
As a result functionality that was previously in the IOMMU drivers has
been moved to the IOMMU core code, including IOMMU group allocation
for each device. The reason for this change was to get more robust
allocation of default domains for the iommu groups.
A couple of fixes were necessary after this was merged into the IOMMU
tree, but there are no known bugs left. The last fix is applied on-top
of the merge commit for the topic branches.
Other than that change, we have:
- Removal of the driver private domain handling in the Intel VT-d
driver. This was fragile code and I am glad it is gone now.
- More Intel VT-d updates from Lu Baolu:
- Nested Shared Virtual Addressing (SVA) support to the Intel VT-d
driver
- Replacement of the Intel SVM interfaces to the common IOMMU SVA
API
- SVA Page Request draining support
- ARM-SMMU Updates from Will:
- Avoid mapping reserved MMIO space on SMMUv3, so that it can be
claimed by the PMU driver
- Use xarray to manage ASIDs on SMMUv3
- Reword confusing shutdown message
- DT compatible string updates
- Allow implementations to override the default domain type
- A new IOMMU driver for the Allwinner Sun50i platform
- Support for ATS gets disabled for untrusted devices (like
Thunderbolt devices). This includes a PCI patch, acked by Bjorn.
- Some cleanups to the AMD IOMMU driver to make more use of IOMMU
core features.
- Unification of some printk formats in the Intel and AMD IOMMU
drivers and in the IOVA code.
- Updates for DT bindings
- A number of smaller fixes and cleanups.
* tag 'iommu-updates-v5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (109 commits)
iommu: Check for deferred attach in iommu_group_do_dma_attach()
iommu/amd: Remove redundant devid checks
iommu/amd: Store dev_data as device iommu private data
iommu/amd: Merge private header files
iommu/amd: Remove PD_DMA_OPS_MASK
iommu/amd: Consolidate domain allocation/freeing
iommu/amd: Free page-table in protection_domain_free()
iommu/amd: Allocate page-table in protection_domain_init()
iommu/amd: Let free_pagetable() not rely on domain->pt_root
iommu/amd: Unexport get_dev_data()
iommu/vt-d: Fix compile warning
iommu/vt-d: Remove real DMA lookup in find_domain
iommu/vt-d: Allocate domain info for real DMA sub-devices
iommu/vt-d: Only clear real DMA device's context entries
iommu: Remove iommu_sva_ops::mm_exit()
uacce: Remove mm_exit() op
iommu/sun50i: Constify sun50i_iommu_ops
iommu/hyper-v: Constify hyperv_ir_domain_ops
iommu/vt-d: Use pci_ats_supported()
iommu/arm-smmu-v3: Use pci_ats_supported()
...
- Fix conflicts in pci-bridge-emul descriptions of Device Status and Slot
Control (Jon Derrick)
- Add emulation for more Device Status, Link Control, and Slot Control
bits (Jon Derrick)
- Improve emulation of reserved bits (Jon Derrick)
* remotes/lorenzo/pci/pci-bridge-emul:
PCI: pci-bridge-emul: Eliminate the 'reserved' member
PCI: pci-bridge-emul: Update for PCIe 5.0 r1.0
PCI: pci-bridge-emul: Fix Root Cap/Status comment
PCI: pci-bridge-emul: Fix PCIe bit conflicts
- Release resource in probe failure path (Wei Hu)
- Retry PCI bus D0 entry if device state is invalid (Wei Hu)
- Use struct_size() to help avoid type mistakes (Gustavo A. R. Silva)
* remotes/lorenzo/pci/hv:
PCI: hv: Use struct_size() helper
PCI: hv: Retry PCI bus D0 entry on invalid device state
PCI: hv: Fix the PCI HyperV probe failure path to release resource properly
- Constify struct pci_ecam_ops (Rob Herring)
- Support building as modules (Rob Herring)
- Eliminate wrappers for pci_host_common_probe() by using DT match table
data (Rob Herring)
* remotes/lorenzo/pci/host-generic:
PCI: host-generic: Eliminate pci_host_common_probe wrappers
PCI: host-generic: Support building as modules
PCI: Constify struct pci_ecam_ops
# Conflicts:
# drivers/pci/controller/dwc/pcie-hisi.c
- Deprecate 'cdns,max-outbound-regions' and 'cdns,no-bar-match-nbits'
bindings in favor of deriving them from 'ranges' and 'dma-ranges'
(Kishon Vijay Abraham I)
- Read Vendor and Device ID as 32 bits (not 16) from DT (Kishon Vijay
Abraham I)
* remotes/lorenzo/pci/cadence:
PCI: cadence: Fix to read 32-bit Vendor ID/Device ID property from DT
PCI: cadence: Remove "cdns,max-outbound-regions" DT property
dt-bindings: PCI: cadence: Deprecate inbound/outbound specific bindings
- Train link immediately after enabling link training to avoid issues
with Compex WLE900VX and Turris MOX devices (Pali Rohár)
- Remove ASPM config and let the PCI core do it (Pali Rohár)
- Interpret zero 'max-link-speed' value as invalid (Pali Rohár)
- Respect the 'max-link-speed' property and improve link training (Marek
Behún)
- Issue PERST via GPIO (Pali Rohár)
- Add PHY support (Marek Behún)
- Use standard PCIe capability macros (Pali Rohár)
- Document new 'max-link-speed', 'phys', and 'reset-gpios' properties
(Marek Behún)
* remotes/lorenzo/pci/aardvark:
dt-bindings: PCI: aardvark: Describe new properties
PCI: aardvark: Replace custom macros by standard linux/pci_regs.h macros
PCI: aardvark: Add PHY support
PCI: aardvark: Add FIXME comment for PCIE_CORE_CMD_STATUS_REG access
PCI: aardvark: Issue PERST via GPIO
PCI: aardvark: Improve link training
PCI: of: Zero max-link-speed value is invalid
PCI: aardvark: Don't blindly enable ASPM L0s and don't write to read-only register
PCI: aardvark: Train link immediately after enabling training
- Check .bridge_d3() hook for NULL before calling it (Bjorn Helgaas)
- Disable PME# for Pericom OHCI/UHCI USB controllers because it's
not reliably asserted on USB hotplug (Kai-Heng Feng)
- Assume ports without DLL Link Active train links in 100 ms to work
around Thunderbolt bridge defects (Mika Westerberg)
* pci/pm:
PCI/PM: Assume ports without DLL Link Active train links in 100 ms
PCI/PM: Adjust pcie_wait_for_link_delay() for caller delay
PCI: Avoid Pericom USB controller OHCI/EHCI PME# defect
serial: 8250_pci: Move Pericom IDs to pci_ids.h
PCI/PM: Call .bridge_d3() hook only if non-NULL
- Add AMD Zen Raven and Renoir Root Ports to P2PDMA whitelist (Alex
Deucher)
* pci/p2pdma:
PCI/P2PDMA: Add AMD Zen Raven and Renoir Root Ports to whitelist
- Clarify that platform_get_irq() should never return 0 (Bjorn Helgaas)
- Check for platform_get_irq() failure consistently (Bjorn Helgaas)
- Replace zero-length array with flexible-array (Gustavo A. R. Silva)
- Unify pcie_find_root_port() and pci_find_pcie_root_port() (Yicong Yang)
- Quirk Intel C620 MROMs, which have non-BARs in BAR locations (Xiaochun
Lee)
- Fix pcie_pme_resume() and pcie_pme_remove() kernel-doc (Jay Fang)
- Rename _DSM constants to align with spec (Krzysztof Wilczyński)
* pci/misc:
PCI: Rename _DSM constants to align with spec
PCI/PME: Fix kernel-doc of pcie_pme_resume() and pcie_pme_remove()
x86/PCI: Mark Intel C620 MROMs as having non-compliant BARs
PCI: Unify pcie_find_root_port() and pci_find_pcie_root_port()
PCI: Replace zero-length array with flexible-array
PCI: Check for platform_get_irq() failure consistently
driver core: platform: Clarify that IRQ 0 is invalid
- Remove unused pciehp EMI() and HP_SUPR_RM() macros (Ani Sinha)
- Use of_node_name_eq() for node name comparisons (Rob Herring)
- Convert shpchp_unconfigure_device() to void (Krzysztof Wilczynski)
* pci/hotplug:
PCI: shpchp: Make shpchp_unconfigure_device() void
PCI: Use of_node_name_eq() for node name comparisons
PCI: pciehp: Remove unused EMI() and HP_SUPR_RM() macros
- Log only ACPI_NOTIFY_DISCONNECT_RECOVER events for EDR, not all ACPI
SYSTEM-level events (Kuppuswamy Sathyanarayanan)
- Rely only on _OSC (not _OSC + HEST FIRMWARE_FIRST) to negotiate AER
Capability ownership (Alexandru Gagniuc)
- Remove HEST/FIRMWARE_FIRST parsing that was previously used to help
intuit AER Capability ownership (Kuppuswamy Sathyanarayanan)
- Remove redundant pci_is_pcie() and dev->aer_cap checks (Kuppuswamy
Sathyanarayanan)
- Print IRQ number used by DPC (Yicong Yang)
* pci/error:
PCI/DPC: Print IRQ number used by port
PCI/AER: Use "aer" variable for capability offset
PCI/AER: Remove redundant dev->aer_cap checks
PCI/AER: Remove redundant pci_is_pcie() checks
PCI/AER: Remove HEST/FIRMWARE_FIRST parsing for AER ownership
PCI/AER: Use only _OSC to determine AER ownership
PCI/EDR: Log only ACPI_NOTIFY_DISCONNECT_RECOVER events
Add driver for the Socionext UniPhier Pro5 SoC endpoint controller.
This controller is based on the DesignWare PCIe core.
And add "host" to existing controller descriontions for the host controller
in Kconfig.
Link: https://lore.kernel.org/r/1589457801-12796-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCAAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAl7WhbkTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXlUnB/0R8dBVSeRfNmyJaadBWKFc/LffwKLD
CQ8PVv22ffkCaEYV2tpnhS6NmkERLNdson4Uo02tVUsjOJ4CrWHTn7aKqYWZyA+O
qv/PiD9TBXJVYMVP2kkyaJlK5KoqeAWBr2kM16tT0cxQmlhE7g0Xo2wU9vhRbU+4
i4F0jffe4lWps65TK392CsPr6UEv1HSel191Py5zLzYqChT+L8WfahmBt3chhsV5
TIUJYQvBwxecFRla7yo+4sUn37ZfcTqD1hCWSr0zs4psW0ge7d80kuaNZS+EqxND
fGm3Bp1BlUuDKsJ/D+AaHLCR47PUZ9t9iMDjZS/ovYglLFwi+h3tAV+W
=LwVR
-----END PGP SIGNATURE-----
Merge tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyper-v updates from Wei Liu:
- a series from Andrea to support channel reassignment
- a series from Vitaly to clean up Vmbus message handling
- a series from Michael to clean up and augment hyperv-tlfs.h
- patches from Andy to clean up GUID usage in Hyper-V code
- a few other misc patches
* tag 'hyperv-next-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux: (29 commits)
Drivers: hv: vmbus: Resolve more races involving init_vp_index()
Drivers: hv: vmbus: Resolve race between init_vp_index() and CPU hotplug
vmbus: Replace zero-length array with flexible-array
Driver: hv: vmbus: drop a no long applicable comment
hyper-v: Switch to use UUID types directly
hyper-v: Replace open-coded variant of %*phN specifier
hyper-v: Supply GUID pointer to printf() like functions
hyper-v: Use UUID API for exporting the GUID (part 2)
asm-generic/hyperv: Add definitions for Get/SetVpRegister hypercalls
x86/hyperv: Split hyperv-tlfs.h into arch dependent and independent files
x86/hyperv: Remove HV_PROCESSOR_POWER_STATE #defines
KVM: x86: hyperv: Remove duplicate definitions of Reference TSC Page
drivers: hv: remove redundant assignment to pointer primary_channel
scsi: storvsc: Re-init stor_chns when a channel interrupt is re-assigned
Drivers: hv: vmbus: Introduce the CHANNELMSG_MODIFYCHANNEL message type
Drivers: hv: vmbus: Synchronize init_vp_index() vs. CPU hotplug
Drivers: hv: vmbus: Remove the unused HV_LOCALIZED channel affinity logic
PCI: hv: Prepare hv_compose_msi_msg() for the VMBus-channel-interrupt-to-vCPU reassignment functionality
Drivers: hv: vmbus: Use a spin lock for synchronizing channel scheduling vs. channel removal
hv_utils: Always execute the fcopy and vss callbacks in a tasklet
...
- added support for MIPSr5 and P5600 cores
- converted Loongson PCI driver into a PCI host driver using the generic
PCI framework
- added emulation of CPUCFG command for Loogonson64 cpus
- removed of LASAT, PMC MSP71xx and NEC MARKEINS/EMMA
- ioremap cleanup
- fix for a race between two threads faulting the same page
- various cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=eAtN
-----END PGP SIGNATURE-----
Merge tag 'mips_5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- added support for MIPSr5 and P5600 cores
- converted Loongson PCI driver into a PCI host driver using the
generic PCI framework
- added emulation of CPUCFG command for Loogonson64 cpus
- removed of LASAT, PMC MSP71xx and NEC MARKEINS/EMMA
- ioremap cleanup
- fix for a race between two threads faulting the same page
- various cleanups and fixes
* tag 'mips_5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (143 commits)
MIPS: ralink: drop ralink_clk_init for mt7621
MIPS: ralink: bootrom: mark a function as __init to save some memory
MIPS: Loongson64: Reorder CPUCFG model match arms
MIPS: Expose Loongson CPUCFG availability via HWCAP
MIPS: Loongson64: Guard against future cores without CPUCFG
MIPS: Fix build warning about "PTR_STR" redefinition
MIPS: Loongson64: Remove not used pci.c
MIPS: Loongson64: Define PCI_IOBASE
MIPS: CPU_LOONGSON2EF need software to maintain cache consistency
MIPS: DTS: Fix build errors used with various configs
MIPS: Loongson64: select NO_EXCEPT_FILL
MIPS: Fix IRQ tracing when call handle_fpe() and handle_msa_fpe()
MIPS: mm: add page valid judgement in function pte_modify
mm/memory.c: Add memory read privilege on page fault handling
mm/memory.c: Update local TLB if PTE entry exists
MIPS: Do not flush tlb page when updating PTE entry
MIPS: ingenic: Default to a generic board
MIPS: ingenic: Add support for GCW Zero prototype
MIPS: ingenic: DTS: Add memory info of GCW Zero
MIPS: Loongson64: Switch to generic PCI driver
...
- Update the ACPICA code in the kernel to upstream revision
20200430:
* Move acpi_gbl_next_cmd_num definition (Erik Kaneda).
* Ignore AE_ALREADY_EXISTS status in the disassembler when parsing
create operators (Erik Kaneda).
* Add status checks to the dispatcher (Erik Kaneda).
* Fix required parameters for _NIG and _NIH (Erik Kaneda).
* Make acpi_protocol_lengths static (Yue Haibing).
- Fix ACPI table reference counting errors in several places, mostly
in error code paths (Hanjun Guo).
- Extend the Generic Event Device (GED) driver to support _Exx and
_Lxx handler methods (Ard Biesheuvel).
- Add new acpi_evaluate_reg() helper and modify the ACPI PCI hotplug
code to use it (Hans de Goede).
- Add new DPTF battery participant driver and make the DPFT power
participant driver create more sysfs device attributes (Srinivas
Pandruvada).
- Improve the handling of memory failures in APEI (James Morse).
- Add new blacklist entry for Acer TravelMate 5735Z to the backlight
driver (Paul Menzel).
- Add i2c address for thermal control to the PMIC driver (Mauro
Carvalho Chehab).
- Allow the ACPI processor idle driver to work on platforms with
only one ACPI C-state present (Zhang Rui).
- Fix kobject reference count leaks in error code paths in two
places (Qiushi Wu).
- Delete unused proc filename macros and make some symbols static
(Pascal Terjan, Zheng Zengkai, Zou Wei).
-----BEGIN PGP SIGNATURE-----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=xH3i
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These update the ACPICA code in the kernel to upstream revision
20200430, fix several reference counting errors related to ACPI
tables, add _Exx / _Lxx support to the GED driver, add a new
acpi_evaluate_reg() helper, add new DPTF battery participant driver
and extend the DPFT power participant driver, improve the handling of
memory failures in the APEI code, add a blacklist entry to the
backlight driver, update the PMIC driver and the processor idle
driver, fix two kobject reference count leaks, and make a few janitory
changes.
Specifics:
- Update the ACPICA code in the kernel to upstream revision 20200430:
- Move acpi_gbl_next_cmd_num definition (Erik Kaneda).
- Ignore AE_ALREADY_EXISTS status in the disassembler when parsing
create operators (Erik Kaneda).
- Add status checks to the dispatcher (Erik Kaneda).
- Fix required parameters for _NIG and _NIH (Erik Kaneda).
- Make acpi_protocol_lengths static (Yue Haibing).
- Fix ACPI table reference counting errors in several places, mostly
in error code paths (Hanjun Guo).
- Extend the Generic Event Device (GED) driver to support _Exx and
_Lxx handler methods (Ard Biesheuvel).
- Add new acpi_evaluate_reg() helper and modify the ACPI PCI hotplug
code to use it (Hans de Goede).
- Add new DPTF battery participant driver and make the DPFT power
participant driver create more sysfs device attributes (Srinivas
Pandruvada).
- Improve the handling of memory failures in APEI (James Morse).
- Add new blacklist entry for Acer TravelMate 5735Z to the backlight
driver (Paul Menzel).
- Add i2c address for thermal control to the PMIC driver (Mauro
Carvalho Chehab).
- Allow the ACPI processor idle driver to work on platforms with only
one ACPI C-state present (Zhang Rui).
- Fix kobject reference count leaks in error code paths in two places
(Qiushi Wu).
- Delete unused proc filename macros and make some symbols static
(Pascal Terjan, Zheng Zengkai, Zou Wei)"
* tag 'acpi-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (32 commits)
ACPI: CPPC: Fix reference count leak in acpi_cppc_processor_probe()
ACPI: sysfs: Fix reference count leak in acpi_sysfs_add_hotplug_profile()
ACPI: GED: use correct trigger type field in _Exx / _Lxx handling
ACPI: DPTF: Add battery participant driver
ACPI: DPTF: Additional sysfs attributes for power participant driver
ACPI: video: Use native backlight on Acer TravelMate 5735Z
arm64: acpi: Make apei_claim_sea() synchronise with APEI's irq work
ACPI: APEI: Kick the memory_failure() queue for synchronous errors
mm/memory-failure: Add memory_failure_queue_kick()
ACPI / PMIC: Add i2c address for thermal control
ACPI: GED: add support for _Exx / _Lxx handler methods
ACPI: Delete unused proc filename macros
ACPI: hotplug: PCI: Use the new acpi_evaluate_reg() helper
ACPI: utils: Add acpi_evaluate_reg() helper
ACPI: debug: Make two functions static
ACPI: sleep: Put the FACS table after using it
ACPI: scan: Put SPCR and STAO table after using it
ACPI: EC: Put the ACPI table after using it
ACPI: APEI: Put the HEST table for error path
ACPI: APEI: Put the error record serialization table for error path
...
All Intel platforms guarantee that all root complex implementations must
send transactions up to IOMMU for address translations. Hence for Intel
RCiEP devices, we can assume some ACS-type isolation even without an ACS
capability.
From the Intel VT-d spec, r3.1, sec 3.16 ("Root-Complex Peer to Peer
Considerations"):
When DMA remapping is enabled, peer-to-peer requests through the
Root-Complex must be handled as follows:
- The input address in the request is translated (through first-level,
second-level or nested translation) to a host physical address (HPA).
The address decoding for peer addresses must be done only on the
translated HPA. Hardware implementations are free to further limit
peer-to-peer accesses to specific host physical address regions (or
to completely disallow peer-forwarding of translated requests).
- Since address translation changes the contents (address field) of
the PCI Express Transaction Layer Packet (TLP), for PCI Express
peer-to-peer requests with ECRC, the Root-Complex hardware must use
the new ECRC (re-computed with the translated address) if it
decides to forward the TLP as a peer request.
- Root-ports, and multi-function root-complex integrated endpoints, may
support additional peer-to-peer control features by supporting PCI
Express Access Control Services (ACS) capability. Refer to ACS
capability in PCI Express specifications for details.
Since Linux didn't give special treatment to allow this exception, certain
RCiEP MFD devices were grouped in a single IOMMU group. This doesn't permit
a single device to be assigned to a guest for instance.
In one vendor system: Device 14.x were grouped in a single IOMMU group.
/sys/kernel/iommu_groups/5/devices/0000:00:14.0
/sys/kernel/iommu_groups/5/devices/0000:00:14.2
/sys/kernel/iommu_groups/5/devices/0000:00:14.3
After this patch:
/sys/kernel/iommu_groups/5/devices/0000:00:14.0
/sys/kernel/iommu_groups/5/devices/0000:00:14.2
/sys/kernel/iommu_groups/6/devices/0000:00:14.3 <<< new group
14.0 and 14.2 are integrated devices, but legacy end points, whereas 14.3
was a PCIe-compliant RCiEP.
00:14.3 Network controller: Intel Corporation Device 9df0 (rev 30)
Capabilities: [40] Express (v2) Root Complex Integrated Endpoint, MSI 00
This permits assigning this device to a guest VM.
[bhelgaas: drop "Fixes" tag since this doesn't fix a bug in that commit]
Link: https://lore.kernel.org/r/1590699462-7131-1-git-send-email-ashok.raj@intel.com
Tested-by: Darrel Goeddel <dgoeddel@forcepoint.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Cc: stable@vger.kernel.org
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Mark Scott <mscott@forcepoint.com>,
Cc: Romil Sharma <rsharma@forcepoint.com>
Print IRQ number used by DPC port, like AER/PME does. It provides
convenience to track DPC interrupts counts of certain port from
/proc/interrupts.
Link: https://lore.kernel.org/r/1589018214-52752-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we used "pos" or "aer_pos" for the offset of the AER Capability.
Use "aer" consistently and initialize it the same way everywhere. No
functional change intended.
Link: https://lore.kernel.org/r/20200529230915.GA479883@bjorn-Precision-5520
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Commit c100beb9cc ("PCI/AER: Use only _OSC to determine AER ownership")
removed the use of HEST in determining AER ownership, but the AER driver
still used HEST to verify AER ownership in some of its APIs.
Per the ACPI spec v6.3, sec 18.3.2.4, some HEST table entries contain a
FIRMWARE_FIRST bit, but that bit does not tell us anything about ownership
of the AER capability.
Remove parsing of HEST to look for FIRMWARE_FIRST.
Add pcie_aer_is_native() for the places that need to know whether the OS
owns the AER capability.
[bhelgaas: commit log, reorder patch, remove unused __aer_firmware_first]
Link: https://lore.kernel.org/r/9a37f53a4e6ff4942ff8e18dbb20b00e16c47341.1590534843.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Also, call pm_runtime_disable() when pm_runtime_get_sync() returns
an error code.
Link: https://lore.kernel.org/r/20200521024709.2368-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Versions of VMD with the Host Physical Address shadow register use this
register to calculate the bus address offset needed to do guest
passthrough of the domain. This register shadows the Host Physical
Address registers including the resource type bits. After calculating
the offset, the extra resource type bits lead to the VMD resources being
over-provisioned at the front and under-provisioned at the back.
Example:
pci 10000:80:02.0: reg 0x10: [mem 0xf801fffc-0xf803fffb 64bit]
Expected:
pci 10000:80:02.0: reg 0x10: [mem 0xf8020000-0xf803ffff 64bit]
If other devices are mapped in the over-provisioned front, it could lead
to resource conflict issues with VMD or those devices.
Link: https://lore.kernel.org/r/20200528030240.16024-3-jonathan.derrick@intel.com
Fixes: a1a3017013 ("PCI: vmd: Fix shadow offsets to reflect spec changes")
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Information printed under verbose_request is clearly used for debugging
only. Remove it and use dev_dbg() instead.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/1590719092-8578-1-git-send-email-boris.ostrovsky@oracle.com
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Link: https://lore.kernel.org/r/20200521031355.7022-1-dinghao.liu@zju.edu.cn
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct hv_dr_state {
...
struct hv_pcidev_description func[];
};
struct pci_bus_relations {
...
struct pci_function_description func[];
} __packed;
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following forms:
offsetof(struct hv_dr_state, func) +
(sizeof(struct hv_pcidev_description) *
(relations->device_count))
offsetof(struct pci_bus_relations, func) +
(sizeof(struct pci_function_description) *
(bus_rel->device_count))
with:
struct_size(dr, func, relations->device_count)
and
struct_size(bus_rel, func, bus_rel->device_count)
respectively.
Link: https://lore.kernel.org/r/20200525164319.GA13596@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Rename PCI-related _DSM constants to align them with the PCI Firmware Spec,
r3.2, sec 4.6. No functional change intended.
Link: https://lore.kernel.org/r/20200526213905.2479381-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AMD Starship USB 3.0 host controller advertises Function Level Reset
support, but it apparently doesn't work. Add a quirk to prevent use of FLR
on this device.
Without this quirk, when attempting to assign (pass through) an AMD
Starship USB 3.0 host controller to a guest OS, the system becomes
increasingly unresponsive over the course of several minutes, eventually
requiring a hard reset. Shortly after attempting to start the guest, I see
these messages:
vfio-pci 0000:05:00.3: not ready 1023ms after FLR; waiting
vfio-pci 0000:05:00.3: not ready 2047ms after FLR; waiting
vfio-pci 0000:05:00.3: not ready 4095ms after FLR; waiting
vfio-pci 0000:05:00.3: not ready 8191ms after FLR; waiting
And then eventually:
vfio-pci 0000:05:00.3: not ready 65535ms after FLR; giving up
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 0.000 msecs
perf: interrupt took too long (642744 > 2500), lowering kernel.perf_event_max_sample_rate to 1000
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 82.270 msecs
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 680.608 msecs
INFO: NMI handler (perf_event_nmi_handler) took too long to run: 100.952 msecs
...
watchdog: BUG: soft lockup - CPU#3 stuck for 22s! [qemu-system-x86:7487]
Tested on a Micro-Star International Co., Ltd. MS-7C59/Creator TRX40
motherboard with an AMD Ryzen Threadripper 3970X.
Link: https://lore.kernel.org/r/20200524003529.598434ff@f31-4.lan
Signed-off-by: Kevin Buettner <kevinb@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AMD Matisse HD Audio & USB 3.0 devices advertise Function Level Reset
support, but hang when an FLR is triggered.
To reproduce the problem, attach the device to a VM, then detach and try to
attach again.
Rename the existing quirk_intel_no_flr(), which was not Intel-specific, to
quirk_no_flr(), and apply it to prevent the use of FLR on these AMD
devices.
Link: https://lore.kernel.org/r/CAAri2DpkcuQZYbT6XsALhx2e6vRqPHwtbjHYeiH7MNp4zmt1RA@mail.gmail.com
Signed-off-by: Marcos Scriven <marcos@scriven.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_ats_supported(), which checks whether a device has an ATS
capability, and whether it is trusted. A device is untrusted if it is
plugged into an external-facing port such as Thunderbolt and could be
spoofing an existing device to exploit weaknesses in the IOMMU
configuration. PCIe ATS is one such weaknesses since it allows
endpoints to cache IOMMU translations and emit transactions with
'Translated' Address Type (10b) that partially bypass the IOMMU
translation.
The SMMUv3 and VT-d IOMMU drivers already disallow ATS and transactions
with 'Translated' Address Type for untrusted devices. Add the check to
pci_enable_ats() to let other drivers (AMD IOMMU for now) benefit from
it.
By checking ats_cap, the pci_ats_supported() helper also returns whether
ATS was globally disabled with pci=noats, and could later include more
things, for example whether the whole PCIe hierarchy down to the
endpoint supports ATS.
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20200520152201.3309416-2-jean-philippe@linaro.org
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This controller can be found on Loongson-2K SoC, Loongson-3
systems with RS780E/LS7A PCH.
The RS780E part of code was previously located at
arch/mips/pci/ops-loongson3.c and now it can use generic PCI
driver implementation.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Don't disable MEM/IO decoding when a device have both non_compliant_bars
and mmio_always_on.
That would allow us quirk devices with junk in BARs but can't disable
their decoding.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Acked-by: Bjorn Helgaas <helgaas@kernel.org>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
No functional change. Get "struct pcie_port *" from private data
pointer of "struct irq_domain" in dw_pcie_irq_domain_free() to make
it look similar to how "struct pcie_port *" is obtained in
dw_pcie_irq_domain_alloc()
Link: https://lore.kernel.org/r/20191220100550.777-1-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
The vim3l board does not work with a standard PCIe switch (ASM1184e),
spitting all kind of errors - hinting at HW misconfiguration (no link,
port enumeration issues, etc).
According to the the Synopsys DWC PCIe Reference Manual, in the section
dedicated to the PLCR register, bit 7 is described (FAST_LINK_MODE) as:
"Sets all internal timers to fast mode for simulation purposes."
it is sound to set this bit from a simulation perspective, but on actual
silicon, which expects timers to have a nominal value, it is not.
Make sure the FAST_LINK_MODE bit is cleared when configuring the RC
to solve this problem.
Link: https://lore.kernel.org/r/20200429164230.309922-1-maz@kernel.org
Fixes: 9c0ef6d34f ("PCI: amlogic: Add the Amlogic Meson PCIe controller driver")
Signed-off-by: Marc Zyngier <maz@kernel.org>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Rob Herring <robh@kernel.org>
On a system that uses the internal DWC MSI widget, I get this
warning from debugfs when CONFIG_GENERIC_IRQ_DEBUGFS is selected:
debugfs: File ':soc:pcie@fc000000' in directory 'domains' already present!
This is due to the fact that the DWC MSI code tries to register two
IRQ domains for the same firmware node, without telling the low
level code how to distinguish them (by setting a bus token). This
further confuses debugfs which tries to create corresponding
files for each domain.
Fix it by tagging the inner domain as DOMAIN_BUS_NEXUS, which is
the closest thing we have as to "generic MSI".
Link: https://lore.kernel.org/r/20200501113921.366597-1-maz@kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
platform_get_resource() may fail and return NULL, so we had better
check its return value to avoid a NULL pointer dereference a bit later
in the code. Fix it to use devm_platform_ioremap_resource_byname()
instead of calling platform_get_resource_byname() and devm_ioremap().
Link: https://lore.kernel.org/r/20200429015027.134485-1-weiyongjun1@huawei.com
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-intel-gw.c:456:5: warning: symbol
'intel_pcie_cpu_addr' was not declared. Should it be static?
Link: https://lore.kernel.org/r/20200415084953.6533-1-yanaijie@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Function dw_pcie_prog_outbound_atu_unroll() does not program the upper
32-bit ATU limit register. Since ATU programming functions limit the
size of the translated region to 4GB by using a u32 size parameter,
these issues may combine into undefined behavior for resource sizes
with non-zero upper 32-bits.
For example, a 128GB address space starting at physical CPU address of
0x2000000000 with size of 0x2000000000 needs the following values
programmed into the lower and upper 32-bit limit registers:
0x3fffffff in the upper 32-bit limit register
0xffffffff in the lower 32-bit limit register
Currently, only the lower 32-bit limit register is programmed with a
value of 0xffffffff but the upper 32-bit limit register is not being
programmed. As a result, the upper 32-bit limit register remains at its
default value after reset of 0x0.
These issues may combine to produce undefined behavior since the ATU
limit address may be lower than the ATU base address. Programming the
upper ATU limit address register prevents such undefined behavior despite
the region size getting truncated due to the 32-bit size limit.
Link: https://lore.kernel.org/r/1585785493-23210-1-git-send-email-alan.mikhak@sifive.com
Signed-off-by: Alan Mikhak <alan.mikhak@sifive.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
Per PCIe 5.0 r1.0, Terms and Acronyms, Page 80:
Reserved register fields must be read only and must return 0 (all 0's
for multi-bit fields) when read. Reserved encodings for register and
packet fields must not be used. Any implementation dependence on a
Reserved field value or encoding will result in an implementation that
is not PCI Express-compliant.
This patch ensures reads will return 0 for any bit not in the Read-Only,
Read-Write, or Write-1-to-Clear bitmasks.
Link: https://lore.kernel.org/r/20200511162117.6674-5-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Add missing bits from PCIe 4.0 and updates for PCIe 5.0 r1.0.
PCIe 4.0:
Device Status bit 6 - W1C - Emergency Power Reduction Detected
Link Control bits 15:14 - RW - DRS Signaling Control
Slot Control bit 13 - RW - Auto Slow Power Limit Disable
PCIe 5.0:
Slot Control bit 14 - RW - In-Band PD Disable
Link: https://lore.kernel.org/r/20200511162117.6674-4-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
The upper 16-bits of Root Control contain the Root Capabilities
register. The code instead describes the Root Status register in the
upper 16-bits, although it uses the correct bit definition for Root
Capabilities, and for Root Status in the next definition.
Fix this comment and add a comment describing the Root Status register.
Link: https://lore.kernel.org/r/20200511162117.6674-3-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
This patch fixes two bit conflicts in the pci-bridge-emul driver:
1. Bit 3 of Device Status (19 of Device Control) is marked as both
Write-1-to-Clear and Read-Only. It should be Write-1-to-Clear.
The Read-Only and Reserved bitmasks are shifted by 1 bit due to this
error.
2. Bit 12 of Slot Control is marked as both Read-Write and Reserved.
It should be Read-Write.
Link: https://lore.kernel.org/r/20200511162117.6674-2-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
R-Car PCIe controller has support to map multiple memory regions for
mapping the outbound memory in local system also the controller limits
single allocation for each region (that is, once a chunk is used from the
region it cannot be used to allocate a new one). This features inspires to
add support for handling multiple memory bases in endpoint framework.
With this patch pci_epc_mem_init() initializes address space for endpoint
controller which support single window and pci_epc_multi_mem_init()
initializes multiple windows supported by endpoint controller.
Link: https://lore.kernel.org/r/1588854799-13710-6-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Use bridge resource definitions instead of using the PCI_BRIDGE_RESOURCES
constant with an integer offeset.
Link: https://lore.kernel.org/r/20200520183411.1534621-2-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Except for Endpoints, we enable PTM at enumeration-time. Previously we did
not account for the fact that Switch Downstream Ports are not permitted to
have a PTM capability; their PTM behavior is controlled by the Upstream
Port (PCIe r5.0, sec 7.9.16). Since Downstream Ports don't have a PTM
capability, we did not mark them as "ptm_enabled", which meant that
pci_enable_ptm() on an Endpoint failed because there was no PTM path to it.
Mark Downstream Ports as "ptm_enabled" if their Upstream Port has PTM
enabled.
Fixes: eec097d431 ("PCI: Add pci_enable_ptm() for drivers to enable PTM on endpoints")
Reported-by: Aditya Paluri <Venkata.AdityaPaluri@synopsys.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
shpchp_unconfigure_device() always returned 0, so there's no reason for a
return value. In addition, remove_board() checked the return value for
possible error which is unnecessary.
Convert shpchp_unconfigure_device() to a void function and remove the
return value check. This addresses the following Coccinelle warning:
drivers/pci/hotplug/shpchp_pci.c:66:5-7: Unneeded variable: "rc". Return "0" on line 86
Link: https://lore.kernel.org/r/20200521190457.1066600-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use "true" instead of 1 to initialize "bool use_dma_mrpc". This resolves
the following Coccinelle warning:
drivers/pci/switch/switchtec.c:28:12-24: WARNING: Assignment of 0/1 to bool variable
Link: https://lore.kernel.org/r/20200521200439.1076672-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Fix kernel-doc of the "srv" parameter to pcie_pme_resume() and
pcie_pme_remove(). Building with W=1 produced these warnings:
drivers/pci/pcie/pme.c:414: warning: Function parameter or member 'srv' not described in 'pcie_pme_resume'
drivers/pci/pcie/pme.c:437: warning: Function parameter or member 'srv' not described in 'pcie_pme_remove'
Link: https://lore.kernel.org/r/1589612414-61682-1-git-send-email-f.fangjian@huawei.com
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On s390 PCI Virtual Functions (VFs) are scanned by firmware and are made
available to Linux via the hot-plug interface. As such the common code
path of doing the scan directly using the parent Physical Function (PF)
is not used and fenced off with the no_vf_scan attribute.
Even if the partition created the VFs itself e.g. using the sriov_numvfs
attribute of a PF, the PF/VF links thus need to be established after the
fact. To do this when a VF is plugged we scan through all functions on
the same zbus and test whether they are the parent PF in which case we
establish the necessary links.
With these links established there is now no more need to fence off
pci_iov_remove_virtfn() for pdev->no_vf_scan as the common code now
works fine.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-3-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Currently pci_iov_add_virtfn() scans the SR-IOV BARs, adds the VF to the
bus and also creates the sysfs links between the newly added VF and its
parent PF.
With pdev->no_vf_scan fencing off the entire pci_iov_add_virtfn() call
s390 as the sole pdev->no_vf_scan user thus ends up missing these sysfs
links which are required for example by QEMU/libvirt.
Instead of duplicating the code refactor pci_iov_add_virtfn() to make
sysfs link creation callable separately.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Link: https://lore.kernel.org/r/20200506154139.90609-1-schnelle@linux.ibm.com
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The PCI Bus Binding specification (IEEE Std 1275-1994 Revision 2.1 [1])
defines both Vendor ID and Device ID to be 32-bits. Fix
pcie-cadence-host.c driver to read 32-bit Vendor ID and Device ID
properties from device tree.
[1] -> https://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf
Link: https://lore.kernel.org/r/20200508130646.23939-4-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
"cdns,max-outbound-regions" device tree property provides the
maximum number of outbound regions supported by the Host PCIe
controller. However the outbound regions are configured based
on what is populated in the "ranges" DT property.
Avoid using two properties for configuring outbound regions and
use only "ranges" property instead.
Link: https://lore.kernel.org/r/20200508130646.23939-3-kishon@ti.com
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tom Joseph <tjoseph@cadence.com>
PCI-E capability macros are already defined in linux/pci_regs.h.
Remove their reimplementation in pcie-aardvark.
Link: https://lore.kernel.org/r/20200430080625.26070-9-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
With recent proposed changes for U-Boot it is possible that bootloader
won't initialize the PHY for this controller (currently the PHY is
initialized regardless whether PCI is used in U-Boot, but with these
proposed changes the PHY is initialized only on request).
Since the mvebu-a3700-comphy driver by Miquèl Raynal supports enabling
PCIe PHY, and since Linux' functionality should be independent on what
bootloader did, add code for enabling generic PHY if found in device OF
node.
The mvebu-a3700-comphy driver does PHY powering via SMC calls to ARM
Trusted Firmware. The corresponding code in ARM Trusted Firmware skips
one register write which U-Boot does not: step 7 ("Enable TX"), see [1].
Instead ARM Trusted Firmware expects PCIe driver to do this step,
probably because the register is in PCIe controller address space,
instead of PHY address space. We therefore add this step into the
advk_pcie_setup_hw function.
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/tree/drivers/marvell/comphy/phy-comphy-3700.c?h=v2.3-rc2#n836
Link: https://lore.kernel.org/r/20200430080625.26070-8-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Miquèl Raynal <miquel.raynal@bootlin.com>
This register is applicable only when the controller is configured for
Endpoint mode, which is not the case for the current version of this
driver.
Attempting to remove this code though caused some ath10k cards to stop
working, so for some unknown reason it is needed here.
This should be investigated and a comment explaining this should be put
before the code, so we add a FIXME comment for now.
Link: https://lore.kernel.org/r/20200430080625.26070-7-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Add support for issuing PERST via GPIO specified in 'reset-gpios'
property (as described in PCI device tree bindings).
Some buggy cards (e.g. Compex WLE900VX or WLE1216) are not detected
after reboot when PERST is not issued during driver initialization.
If bootloader already enabled link training then issuing PERST has no
effect for some buggy cards (e.g. Compex WLE900VX) and these cards are
not detected. We therefore clear the LINK_TRAINING_EN register before.
It was observed that Compex WLE900VX card needs to be in PERST reset
for at least 10ms if bootloader enabled link training.
Tested on Turris MOX.
Link: https://lore.kernel.org/r/20200430080625.26070-6-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Currently the aardvark driver trains link in PCIe gen2 mode. This may
cause some buggy gen1 cards (such as Compex WLE900VX) to be unstable or
even not detected. Moreover when ASPM code tries to retrain link second
time, these cards may stop responding and link goes down. If gen1 is
used this does not happen.
Unconditionally forcing gen1 is not a good solution since it may have
performance impact on gen2 cards.
To overcome this, read 'max-link-speed' property (as defined in PCI
device tree bindings) and use this as max gen mode. Then iteratively try
link training at this mode or lower until successful. After successful
link training choose final controller gen based on Negotiated Link Speed
from Link Status register, which should match card speed.
Link: https://lore.kernel.org/r/20200430080625.26070-5-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Interpret zero value of max-link-speed property as invalid,
as the device tree bindings documentation specifies.
Link: https://lore.kernel.org/r/20200430080625.26070-4-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Trying to change Link Status register does not have any effect as this
is a read-only register. Trying to overwrite bits for Negotiated Link
Width does not make sense.
In future proper change of link width can be done via Lane Count Select
bits in PCIe Control 0 register.
Trying to unconditionally enable ASPM L0s via ASPM Control bits in Link
Control register is wrong. There should be at least some detection if
endpoint supports L0s as isn't mandatory.
Moreover ASPM Control bits in Link Control register are controlled by
pcie/aspm.c code which sets it according to system ASPM settings,
immediately after aardvark driver probes. So setting these bits by
aardvark driver has no long running effect.
Remove code which touches ASPM L0s bits from this driver and let
kernel's ASPM implementation to set ASPM state properly.
Some users are reporting issues that this code is problematic for some
Intel wifi cards and removing it fixes them, see e.g.:
https://bugzilla.kernel.org/show_bug.cgi?id=196339
If problems with Intel wifi cards occur even after this commit, then
pcie/aspm.c code could be modified / hooked to not enable ASPM L0s state
for affected problematic cards.
Link: https://lore.kernel.org/r/20200430080625.26070-3-pali@kernel.org
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Adding even 100ms (PCI_PM_D3COLD_WAIT) delay between enabling link
training and starting link training causes detection issues with some
buggy cards (such as Compex WLE900VX).
Move the code which enables link training immediately before the one
which starts link traning.
This fixes detection issues of Compex WLE900VX card on Turris MOX after
cold boot.
Link: https://lore.kernel.org/r/20200430080625.26070-2-pali@kernel.org
Fixes: f4c7d053d7 ("PCI: aardvark: Wait for endpoint to be ready...")
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Kai-Heng Feng reported that it takes a long time (> 1 s) to resume
Thunderbolt-connected devices from both runtime suspend and system sleep
(s2idle).
This was because some Downstream Ports that support > 5 GT/s do not also
support Data Link Layer Link Active reporting. Per PCIe r5.0 sec 6.6.1:
With a Downstream Port that supports Link speeds greater than 5.0 GT/s,
software must wait a minimum of 100 ms after Link training completes
before sending a Configuration Request to the device immediately below
that Port. Software can determine when Link training completes by polling
the Data Link Layer Link Active bit or by setting up an associated
interrupt (see Section 6.7.3.3).
Sec 7.5.3.6 requires such Ports to support DLL Link Active reporting, but
at least the Intel JHL6240 Thunderbolt 3 Bridge [8086:15c0] and the Intel
JHL7540 Thunderbolt 3 Bridge [8086:15ea] do not.
Previously we tried to wait for Link training to complete, but since there
was no DLL Link Active reporting, all we could do was wait the worst-case
1000 ms, then another 100 ms.
Instead of using the supported speeds to determine whether to wait for Link
training, check whether the port supports DLL Link Active reporting. The
Ports in question do not, so we'll wait only the 100 ms required for Ports
that support Link speeds <= 5 GT/s.
This of course assumes these Ports always train the Link within 100 ms even
if they are operating at > 5 GT/s, which is not required by the spec.
[bhelgaas: commit log, comment]
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206837
Link: https://lore.kernel.org/r/20200514133043.27429-1-mika.westerberg@linux.intel.com
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The caller of pcie_wait_for_link_delay() specifies the time to wait after
the link becomes active. When the downstream port doesn't support link
active reporting, obviously we can't tell when the link becomes active, so
we waited the worst-case time (1000 ms) plus 100 ms, ignoring the delay
from the caller.
Instead, wait for 1000 ms + the delay from the caller.
Fixes: 4827d63891 ("PCI/PM: Add pcie_wait_for_link_delay()")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Root Complex Integrated Endpoints (RCiEPs) do not have an upstream bridge,
so pci_configure_mps() previously ignored them, which may result in reduced
performance.
Instead, program the Max_Payload_Size of RCiEPs to the maximum supported
value (unless it is limited for the PCIE_BUS_PEER2PEER case). This also
affects the subsequent programming of Max_Read_Request_Size because Linux
programs MRRS based on the MPS value.
Fixes: 9dae3a9729 ("PCI: Move MPS configuration check to pci_configure_device()")
Link: https://lore.kernel.org/r/1585343775-4019-1-git-send-email-ashok.raj@intel.com
Tested-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
The PCI code has several paths where the struct pci_host_bridge is freed
directly. This is wrong because it contains a struct device which is
refcounted and should be freed using put_device(). This can result in
use-after-free errors. I think this problem has existed since 2012 with
commit 7b54366358 ("PCI: add generic device into pci_host_bridge
struct"). It generally hasn't mattered as most host bridge drivers are
still built-in and can't unbind.
The problem is a struct device should never be freed directly once
device_initialize() is called and a ref is held, but that doesn't happen
until pci_register_host_bridge(). There's then a window between allocating
the host bridge and pci_register_host_bridge() where kfree should be used.
This is fragile and requires callers to do the right thing. To fix this, we
need to split device_register() into device_initialize() and device_add()
calls, so that the host bridge struct is always freed by using a
put_device().
devm_pci_alloc_host_bridge() is using devm_kzalloc() to allocate struct
pci_host_bridge which will be freed directly. Instead, we can use a custom
devres action to call put_device().
Link: https://lore.kernel.org/r/20200513223859.11295-2-robh@kernel.org
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
If device_register() has an error, we should bail out of
pci_register_host_bridge() rather than continuing on.
Fixes: 37d6a0a6f4 ("PCI: Add pci_register_host_bridge() interface")
Link: https://lore.kernel.org/r/20200513223859.11295-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Previously we used pcie_find_root_port() to find a Root Port from a PCIe
device and pci_find_pcie_root_port() to find a Root Port from a
Conventional PCI device.
Unify the two functions and use pcie_find_root_port() to find a Root Port
from either a Conventional PCI device or a PCIe device. Then there is no
need to distinguish the type of the device.
Link: https://lore.kernel.org/r/1589019568-5216-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org> # wireless
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> # thunderbolt
xHCI's PCI fixup, run at the end of pcie-brcmstb's probe, depends on
RPi4's VideoCore firmware interface to be up and running. It's possible
for both initializations to race, so make sure it's available prior to
starting.
Link: https://lore.kernel.org/r/20200505161318.26200-4-nsaenzjulienne@suse.de
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
The current codebase makes use of the zero-length array language extension
to the C90 standard, but the preferred mechanism to declare variable-length
types such as these as a flexible array member [1][2], introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning in
case the flexible array does not occur last in the structure, which will
help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that dynamic memory allocations won't be affected by this
change:
Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero. [1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type [1]. There are some instances of code in which
the sizeof() operator is being incorrectly/erroneously applied to
zero-length arrays, and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also help
to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Link: https://lore.kernel.org/r/20200507190544.GA15633@embeddedor
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The platform_get_irq*() interfaces return either a negative error number or
a valid IRQ. 0 is not a valid return value, so check for "< 0" to detect
failure as recommended by the function documentation.
On failure, return the error number from platform_get_irq*() instead of
making up a new one.
Link: https://lore.kernel.org/r/cover.1583952275.git.amanharitsh123@gmail.com
[bhelgaas: commit log, squash into one patch]
Signed-off-by: Aman Sharma <amanharitsh123@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Karthikeyan Mitran <m.karthikeyan@mobiveil.co.in>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
When kdump is triggered, some PCI devices may have not been shut down
cleanly before the kdump kernel starts.
This causes the initial attempt to enter D0 state in the kdump kernel to
fail with invalid device state returned from Hyper-V host.
When this happens, explicitly call hv_pci_bus_exit() and retry to enter
the D0 state.
Link: https://lore.kernel.org/r/20200507050300.10974-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
In some error cases in hv_pci_probe(), allocated resources are not freed.
Fix this by adding a field to keep track of the high water mark for slots
that have resources allocated to them. In case of an error, this high
water mark is used to know which slots have resources that must be released.
Since slots are numbered starting with zero, a value of -1 indicates no
slots have been allocated resources. There may be unused slots in the range
between slot 0 and the high water mark slot, but these slots are already
ignored by the existing code in the allocate and release loops with the call
to get_pcichild_wslot().
Link: https://lore.kernel.org/r/20200507050211.10923-1-weh@microsoft.com
Signed-off-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Some informal internal experiments has shown that the BrcmSTB ASPM L0s
savings may introduce an undesirable noise signal on some customers'
boards. In addition, L0s was found lacking in realized power savings,
especially relative to the L1 ASPM component. This is BrcmSTB's
experience and may not hold for others. At any rate, if the
'aspm-no-l0s' property is present L0s will be disabled.
Link: https://lore.kernel.org/r/20200507201544.43432-5-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
The outbound memory window registers were being referenced
with an incorrect stride offset. This probably wasn't noticed
previously as there was likely only one such window employed.
Link: https://lore.kernel.org/r/20200507201544.43432-3-james.quinlan@broadcom.com
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
clk_put() was being invoked on a clock obtained by
devm_clk_get_optional().
Link: https://lore.kernel.org/r/20200507201544.43432-2-james.quinlan@broadcom.com
Signed-off-by: Jim Quinlan <jquinlan@broadcom.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
While preparing the driver for upstream this detail was missed.
If not asserted during the initialization process, devices connected on
the bus will not be made aware of the internal reset happening. This,
potentially resulting in unexpected behavior.
Link: https://lore.kernel.org/r/20200507172020.18000-1-nsaenzjulienne@suse.de
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
pci_epc_mem_init() internally used page size equal to *PAGE_SIZE* to
manage the address space so instead just pass the page size as a
argument to pci_epc_mem_init().
Also make pci_epc_mem_init() as a C function instead of a macro function
in preparation for adding support for pci-epc-mem core to handle multiple
windows.
Link: https://lore.kernel.org/r/1588854799-13710-5-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The mask value was calculated incorrectly for PCIEPAMR register if the
size was less than 128 bytes. Fix this issue by adding a check on size.
Link: https://lore.kernel.org/r/1588854799-13710-4-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Move shareable code to common file pcie-rcar.c and the #defines to
pcie-rcar.h so that the common code can be reused with endpoint driver.
There are no functional changes with this patch for the host controller
driver.
Link: https://lore.kernel.org/r/1588854799-13710-3-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
This commit renames pcie-rcar.c to pcie-rcar-host.c in preparation for
adding support for endpoint mode. CONFIG_PCIE_RCAR is kept so that arm64
defconfig change can be a separate patch.
With this patch both config options PCIE_RCAR and PCIE_RCAR_HOST will be
available but PCIE_RCAR internally selects PCIE_RCAR_HOST so that bisect
builds wont be affected.
Link: https://lore.kernel.org/r/1588854799-13710-2-git-send-email-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Error code is stored in rp->reset_gpio and not in err variable.
Link: https://lore.kernel.org/r/20200414102512.27506-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Use the new acpi_evaluate_reg() helper in the acpiphp_glue.c code.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Both Pericom OHCI and EHCI devices advertise PME# support from all power
states:
06:00.0 USB controller [0c03]: Pericom Semiconductor PI7C9X442SL USB OHCI Controller [12d8:400e] (rev 01) (prog-if 10 [OHCI])
Subsystem: Pericom Semiconductor PI7C9X442SL USB OHCI Controller [12d8:400e]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
06:00.2 USB controller [0c03]: Pericom Semiconductor PI7C9X442SL USB EHCI Controller [12d8:400f] (rev 01) (prog-if 20 [EHCI])
Subsystem: Pericom Semiconductor PI7C9X442SL USB EHCI Controller [12d8:400f]
Capabilities: [80] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
But testing shows that it's unreliable: there is a 20% chance PME# won't be
asserted when a USB device is plugged.
Remove PME support for both devices to make USB plugging work reliably.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205981
Link: https://lore.kernel.org/r/20200508065343.32751-2-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
7d715a6c1a ("PCI: add PCI Express ASPM support") added the ability for
Linux to enable ASPM, but for some undocumented reason, it didn't enable
ASPM on links where the downstream component is a PCIe-to-PCI/PCI-X Bridge.
Remove this exclusion so we can enable ASPM on these links.
The Dell OptiPlex 7080 mentioned in the bugzilla has a TI XIO2001
PCIe-to-PCI Bridge. Enabling ASPM on the link leading to it allows the
Intel SoC to enter deeper Package C-states, which is a significant power
savings.
[bhelgaas: commit log]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=207571
Link: https://lore.kernel.org/r/20200505173423.26968-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add suspend/resume support for rcar. The resume handler reprograms the
hardware based on the software state kept in specific device structures,
so there is no need to save registers on suspend.
Link: https://lore.kernel.org/r/20200314191232.3122290-1-marek.vasut@gmail.com
Link: https://lore.kernel.org/r/20200426123148.56051-1-marek.vasut@gmail.com
Signed-off-by: Kazufumi Ikeda <kaz-ikeda@xc.jp.nec.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: linux-renesas-soc@vger.kernel.org
The outbound windows (PCIEPAUR(x), PCIEPALR(x)) describe a mapping between
a CPU address (which is determined by the window number 'x') and a
programmed PCI address - Thus allowing the controller to translate CPU
accesses into PCI accesses.
However the existing code incorrectly writes the CPU address - lets fix
this by writing the PCI address instead.
For memory transactions, existing DT users describe a 1:1 identity mapping
and thus this change should have no effect. However the same isn't true for
I/O.
Link: https://lore.kernel.org/r/20191004132941.6660-1-andrew.murray@arm.com
Fixes: c25da47788 ("PCI: rcar: Add Renesas R-Car PCIe driver")
Tested-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Most ECAM host drivers are just different pci_ecam_ops which can be DT
match table data. That's already the case in some cases, but let's
do that for all the ECAM drivers. Then we can use
of_device_get_match_data() in pci_host_common_probe() and eliminate the
probe wrapper functions and use pci_host_common_probe() directly for
probe.
Link: https://lore.kernel.org/r/20200409234923.21598-4-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
When unbinding pci_epf_test, pci_epf_test_clean_dma_chan() is called in
pci_epf_test_unbind() even though epf_test->dma_supported is false.
As a result, dma_release_channel() will trigger a NULL pointer
dereference because dma_chan is not set.
Avoid calling dma_release_channel() if epf_test->dma_supported
is false.
Link: https://lore.kernel.org/r/1587540287-10458-1-git-send-email-hayashi.kunihiko@socionext.com
Fixes: 5ebf3fc59b ("PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
If we fails somewhere in 'v3_pci_probe()', we need to free 'host'.
Use the managed version of 'pci_alloc_host_bridge()' to do that easily.
The use of managed resources is already widely used in this driver.
Link: https://lore.kernel.org/r/20200418081637.1585-1-christophe.jaillet@wanadoo.fr
Fixes: 68a15eb7bd ("PCI: v3-semi: Add V3 Semiconductor PCI host driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warning:
drivers/pci/controller/dwc/pcie-hisi.c:365:21: warning:
symbol 'hisi_pcie_platform_ops' was not declared. Should it be static?
Link: https://lore.kernel.org/r/1587611883-26960-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Zhou Wang <wangzhou1@hisilicon.com>
Commit 6f5e193bfb ("PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get
correct MSI-X table address") overcomplicated the computation of the
msix_tbl address. Simplify it as it's simply the addr + offset. Provided
addr is (void *) already.
objdump -d shows no difference after this patch.
Link: https://lore.kernel.org/r/20200420065227.4920-1-jslaby@suse.cz
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
When resizing a BAR, pci_reassign_bridge_resources() is invoked to bring
the bridge windows of parent bridges in line with the new BAR assignment.
This assumes the device whose BAR is being resized lives on a subordinate
bus, but this is not necessarily the case. A device may live on the root
bus, in which case dev->bus->self is NULL, and passing a NULL pci_dev
pointer to pci_reassign_bridge_resources() will cause it to crash.
So let's make the call to pci_reassign_bridge_resources() conditional on
whether dev->bus->self is non-NULL in the first place.
Fixes: 8bb705e3e7 ("PCI: Add pci_resize_resource() for resizing BARs")
Link: https://lore.kernel.org/r/20200421162256.26887-1-ardb@kernel.org
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Enable building host-generic and its host-common dependency as a
module.
Link: https://lore.kernel.org/r/20200409234923.21598-3-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Will Deacon <will@kernel.org>
Cc: linux-pci@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
struct pci_ecam_ops is typically DT match table data which is defined to
be const. It's also best practice for ops structs to be const. Ideally,
we'd make struct pci_ops const as well, but that becomes pretty
invasive, so for now we just cast it where needed.
Link: https://lore.kernel.org/r/20200409234923.21598-2-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Jonathan Chocron <jonnyc@amazon.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
Cc: Robert Richter <rrichter@marvell.com>
Cc: Toan Le <toan@os.amperecomputing.com>
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Cc: linux-acpi@vger.kernel.org
Per the PCI Firmware spec, r3.2, sec 4.5.1, the OS can request control of
AER via bit 3 of the _OSC Control Field. In the returned value of the
Control Field:
The firmware sets [bit 3] to 1 to grant control over PCI Express Advanced
Error Reporting. ... after control is transferred to the operating
system, firmware must not modify the Advanced Error Reporting Capability.
If control of this feature was requested and denied or was not requested,
firmware returns this bit set to 0.
Previously the pci_root driver looked at the HEST FIRMWARE_FIRST bit to
determine whether to request ownership of the AER Capability. This was
based on ACPI spec v6.3, sec 18.3.2.4, and similar sections, which say
things like:
Bit [0] - FIRMWARE_FIRST: If set, indicates that system firmware will
handle errors from this source first.
Bit [1] - GLOBAL: If set, indicates that the settings contained in this
structure apply globally to all PCI Express Devices.
These ACPI references don't say anything about ownership of the AER
Capability.
Remove use of the FIRMWARE_FIRST bit and rely only on the _OSC bit to
determine whether we have control of the AER Capability.
Link: https://lore.kernel.org/r/20181115231605.24352-1-mr.nuke.me@gmail.com/ v1
Link: https://lore.kernel.org/r/20190326172343.28946-1-mr.nuke.me@gmail.com/ v2
Link: https://lore.kernel.org/r/67af2931705bed9a588b5a39d369cb70b9942190.1587925636.git.sathyanarayanan.kuppuswamy@linux.intel.com
[bhelgaas: commit log, note: Alex posted this identical patch 18 months
ago, and I failed to apply it then, so I made him the author, added links
to his postings, and added his Signed-off-by]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jon Derrick <jonathan.derrick@intel.com>
The Physical function should not be disabled until no virtual
functions depends on it.
Let's force the user to first use echo 0 > sriov_numfs before
allowing to disable the PF with echo 0 > power.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
We allow multiple functions on a single bus.
We suppress the ZPCI_DEVFN definition and replace its
occurences with zpci->devfn.
We verify the number of device during the registration.
There can never be more domains in use than existing
devices, so we do not need to verify the count of domain
after having verified the count of devices.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
The zPCI bus is in charge to handle common zPCI resources for
zPCI devices.
Creating the zPCI bus, the PCI bus, the zPCI devices and the
PCI devices and hotplug slots
done in a specific order:
- PCI hotplug slot creation needs a PCI bus
- PCI bus needs a PCI domain
which is reported by the pci_domain_nr() when setting up the
host bridge
- PCI domain is set from the zPCI with devfn 0
this is necessary to have a reproducible enumeration
Therefore we can not create devices or hotplug slots for any PCI
device associated with a zPCI device before having discovered
the function zero of the bus.
The discovery and initialization of devices can be done at several
points in the code:
- On Events, serialized in a thread context
- On initialization, in the kernel init thread context
- When powering on the hotplug slot, in a user thread context
The removal of devices and their parent bus may also be done on
events or for devices when powering down the slot.
To guarantee the existence of the bus and devices until they are
no more needed we use kref in zPCI bus and introduce a reference
count in the zPCI devices.
In this patch the zPCI bus still only accept a device with
a devfn 0.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Convert string compares of DT node names to use of_node_name_eq() helper
instead. This removes direct access to the node name pointer.
Link: https://lore.kernel.org/r/20200416215114.7715-1-robh@kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
PCIe Advanced Error Reporting (AER) is optional and there's no need for it
to be selected by default.
Remove the "default y" for CONFIG_PCIEAER.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Russell Currey <ruscur@russell.cc>
Cc: Sam Bobroff <sbobroff@linux.ibm.com>
Cc: Oliver O'Halloran <oohall@gmail.com>
Drivers should not be selected by default because that bloats the kernel
for people who don't need them.
Remove the "default y" for CONFIG_PCI_KEYSTONE_HOST.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Drivers should not be selected by default because that bloats the kernel
for people who don't need them.
Enable CONFIG_PCI_DRA7XX_HOST by default only if SOC_DRA7XX.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: linux-omap@vger.kernel.org
26ad34d510 ("PCI / ACPI: Whitelist D3 for more PCIe hotplug ports") added
the struct pci_platform_pm_ops.bridge_d3() function pointer and
platform_pci_bridge_d3() to use it.
The .bridge_d3() op is implemented by acpi_pci_platform_pm, but not by
mid_pci_platform_pm. We don't expect platform_pci_bridge_d3() to be called
on Intel MID platforms, but nothing in the code itself would prevent that.
Check the .bridge_d3() pointer for NULL before calling it.
Fixes: 26ad34d510 ("PCI / ACPI: Whitelist D3 for more PCIe hotplug ports")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rename DPM_FLAG_NEVER_SKIP to DPM_FLAG_NO_DIRECT_COMPLETE which
matches its purpose more closely.
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com> # for PCI parts
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Because all callers of dev_pm_smart_suspend_and_suspended use it only
for checking whether or not to skip driver suspend callbacks for a
device, rename it to dev_pm_skip_suspend() in analogy with
dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The name of dev_pm_may_skip_resume() may be easily confused with the
power.may_skip_resume flag which is not checked by that function, so
rename the former as dev_pm_skip_resume().
No functional impact.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Because the power.may_skip_resume device status bit is taken
into account in combination with the DPM_FLAG_LEAVE_SUSPENDED
driver flag, it can be set to 'true' for all devices in the
"suspend" phase of a suspend-resume cycle, so do that.
Then, neither the PM core nor the middle-layer (sybsystem) code
handling it needs to set it to 'true' any more and it just has
to be cleared if there is a reason to avoid skipping the "noirq"
and "early" resume callbacks provided by the driver, so update
the code in question accordingly.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
The current code in device_resume_noirq() causes the entire early
resume and resume phases of device suspend to be skipped for
devices for which the noirq resume phase have been skipped (due
to the LEAVE_SUSPENDED flag being set) on the premise that those
devices should stay in runtime-suspend after system-wide resume.
However, that may not be correct in two situations. First, the
middle layer (subsystem) noirq resume callback may be missing for
a given device, but its early resume callback may be present and it
may need to do something even if it decides to skip the driver
callback. Second, if the device's wakeup settings were adjusted
in the suspend phase without resuming the device (that was in
runtime suspend at that time), they most likely need to be
adjusted again in the resume phase and so the driver callback
in that phase needs to be run.
For the above reason, modify the core to allow the middle layer
->resume_late callback to run even if its ->resume_noirq callback
is missing (and the core has skipped the driver-level callback
in that phase) and to allow all device callbacks to run in the
resume phase. Also make the core set the PM-runtime status of
devices with SMART_SUSPEND set whose resume callbacks are not
skipped to "active" in the "noirq" resume phase and update the
affected subsystems (PCI and ACPI) accordingly.
After this change, middle-layer (subsystem) callbacks will always
be invoked in all phases of system suspend and resume and driver
callbacks will always run in the prepare, suspend, resume, and
complete phases for all devices.
For devices with SMART_SUSPEND set, driver callbacks will be
skipped in the late and noirq phases of system suspend if those
devices remain in runtime suspend in __device_suspend_late().
Driver callbacks will also be skipped for them during the
noirq and early phases of the "thaw" transition related to
hibernation in that case.
Setting LEAVE_SUSPENDED means that the driver allows its callbacks
to be skipped in the noirq and early phases of system resume, but
some additional conditions need to be met for that to happen (among
other things, the power.may_skip_resume flag needs to be set for the
device during system suspend for the driver callbacks to be skipped
during the subsequent resume transition).
For all devices with SMART_SUSPEND set whose driver callbacks are
invoked during system resume, the PM-runtime status will be set to
"active" (by the core).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
According to the hardware architect, pre-Zen parts support p2p writes and
Zen parts support both p2p reads and writes.
Add entries for Zen parts Raven (0x15d0) and Renoir (0x1630).
Link: https://lore.kernel.org/r/20200406194201.846411-1-alexander.deucher@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Christian König <christian.koenig@amd.com>
Acked-by: Huang Rui <ray.huang@amd.com>
The current implementation of hv_compose_msi_msg() is incompatible with
the new functionality that allows changing the vCPU a VMBus channel will
interrupt: if this function always calls hv_pci_onchannelcallback() in
the polling loop, the interrupt going to a different CPU could cause
hv_pci_onchannelcallback() to be running simultaneously in a tasklet,
which will break. The current code also has a problem in that it is not
synchronized with vmbus_reset_channel_cb(): hv_compose_msi_msg() could
be accessing the ring buffer via the call of hv_pci_onchannelcallback()
well after the time that vmbus_reset_channel_cb() has finished.
Fix these issues as follows. Disable the channel tasklet before
entering the polling loop in hv_compose_msi_msg() and re-enable it when
done. This will prevent hv_pci_onchannelcallback() from running in a
tasklet on a different CPU. Moreover, poll by always calling
hv_pci_onchannelcallback(), but check the channel callback function for
NULL and invoke the callback within a sched_lock critical section. This
will prevent hv_compose_msi_msg() from accessing the ring buffer after
vmbus_reset_channel_cb() has acquired the sched_lock spinlock.
Suggested-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <amurray@thegoodpenguin.co.uk>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: <linux-pci@vger.kernel.org>
Link: https://lore.kernel.org/r/20200406001514.19876-8-parri.andrea@gmail.com
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Wei Liu <wei.liu@kernel.org>
Some Google Apex Edge TPU devices have a class code of 0
(PCI_CLASS_NOT_DEFINED). This prevents the PCI core from assigning
resources for the Apex BARs because __dev_sort_resources() ignores
classless devices, host bridges, and IOAPICs.
On x86, firmware typically assigns those resources, so this was not a
problem. But on some architectures, firmware does *not* assign BARs, and
since the PCI core didn't do it either, the Apex device didn't work
correctly:
apex 0000:01:00.0: can't enable device: BAR 0 [mem 0x00000000-0x00003fff 64bit pref] not claimed
apex 0000:01:00.0: error enabling PCI device
f390d08d8b ("staging: gasket: apex: fixup undefined PCI class") added a
quirk to fix the class code, but it was in the apex driver, and if the
driver was built as a module, it was too late to help.
Move the quirk to the PCI core, where it will always run early enough that
the PCI core will assign resources if necessary.
Link: https://lore.kernel.org/r/CAEzXK1r0Er039iERnc2KJ4jn7ySNUOG9H=Ha8TD8XroVqiZjgg@mail.gmail.com
Fixes: f390d08d8b ("staging: gasket: apex: fixup undefined PCI class")
Reported-by: Luís Mendes <luis.p.mendes@gmail.com>
Debugged-by: Luís Mendes <luis.p.mendes@gmail.com>
Tested-by: Luis Mendes <luis.p.mendes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Todd Poynor <toddpoynor@google.com>
Including:
- ARM-SMMU support for the TLB range invalidation command in
SMMUv3.2.
- ARM-SMMU introduction of command batching helpers to batch up
CD and ATC invalidation.
- ARM-SMMU support for PCI PASID, along with necessary PCI
symbol exports.
- Introduce a generic (actually rename an existing) IOMMU
related pointer in struct device and reduce the IOMMU related
pointers.
- Some fixes for the OMAP IOMMU driver to make it build on 64bit
architectures.
- Various smaller fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=nhuS
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- ARM-SMMU support for the TLB range invalidation command in SMMUv3.2
- ARM-SMMU introduction of command batching helpers to batch up CD and
ATC invalidation
- ARM-SMMU support for PCI PASID, along with necessary PCI symbol
exports
- Introduce a generic (actually rename an existing) IOMMU related
pointer in struct device and reduce the IOMMU related pointers
- Some fixes for the OMAP IOMMU driver to make it build on 64bit
architectures
- Various smaller fixes and improvements
* tag 'iommu-updates-v5.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (39 commits)
iommu: Move fwspec->iommu_priv to struct dev_iommu
iommu/virtio: Use accessor functions for iommu private data
iommu/qcom: Use accessor functions for iommu private data
iommu/mediatek: Use accessor functions for iommu private data
iommu/renesas: Use accessor functions for iommu private data
iommu/arm-smmu: Use accessor functions for iommu private data
iommu/arm-smmu: Refactor master_cfg/fwspec usage
iommu/arm-smmu-v3: Use accessor functions for iommu private data
iommu: Introduce accessors for iommu private data
iommu/arm-smmu: Fix uninitilized variable warning
iommu: Move iommu_fwspec to struct dev_iommu
iommu: Rename struct iommu_param to dev_iommu
iommu/tegra-gart: Remove direct access of dev->iommu_fwspec
drm/msm/mdp5: Remove direct access of dev->iommu_fwspec
ACPI/IORT: Remove direct access of dev->iommu_fwspec
iommu: Define dev_iommu_fwspec_get() for !CONFIG_IOMMU_API
iommu/virtio: Reject IOMMU page granule larger than PAGE_SIZE
iommu/virtio: Fix freeing of incomplete domains
iommu/virtio: Fix sparse warning
iommu/vt-d: Add build dependency on IOASID
...
- A large series from Nick for 64-bit to further rework our exception vectors,
and rewrite portions of the syscall entry/exit and interrupt return in C. The
result is much easier to follow code that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had become badly
intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings from the
workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and update the
status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to:
Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew Donnellan, Aneesh
Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen Zhou, Christophe JAILLET,
Christophe Leroy, Christoph Hellwig, Clement Courbet, Daniel Axtens, David
Gibson, Douglas Miller, Fabiano Rosas, Fangrui Song, Ganesh Goudar, Gautham R.
Shenoy, Greg Kroah-Hartman, Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie
Halip, Jan Kara, Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger,
Laurentiu Tudor, Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh
Salgaonkar, Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira,
Michael Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat, Rasmus Villemoes, Ravi
Bangoria, Roman Bolshakov, Sam Bobroff, Sandipan Das, Santosh S, Sedat Dilek,
Segher Boessenkool, Shilpasri G Bhat, Sourabh Jain, Srikar Dronamraju, Stephen
Rothwell, Tyrel Datwyler, Vaibhav Jain, YueHaibing.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEJFGtCPCthwEv2Y/bUevqPMjhpYAFAl6JypATHG1wZUBlbGxl
cm1hbi5pZC5hdQAKCRBR6+o8yOGlgOTyD/0U90tXb3VXlQcc4OFIb8vWIj76k4Zn
ZSZ7RyOuvb5pCISBZjSK79XkR9eMHT77qagX4V41q64k4yQl8nbgLeVnwL76hLLc
IJCs23f4nsO0uqX/MhSCc5dfOOOS2i8V+OQYtsYWsH5QaG95v0cHIqVaHHMlfQxu
507GO/W5W6KTd4x008b5unQOuE51zMKlKvqEJXkT59obQFpaa2S5Wn7OzhsnarCH
YSRNxaC7vtgBKLA9wUnFh8UUbh0FbOwXBCaq4OhHMhgRihdteVBCzlcR/6c+IRbt
EoZxKzfQ0hI1z5f++kJNaRXMtUbSpM8D1HdKKHgiWjpdBSD0eu2X106KQT2R2ZOF
qhX8xPLWNzdBglA6L43AaZUu+4ayd3QrrJIkjDv/K1rCHZjfGOzSQfoZgTEBNLFA
tC0crhEfw8m98e4EwhCtekGQxdczRdLS9YvtC/h6mU2xkpA35yNSwB1/iuVQdkYD
XyrEqImAQ1PJla7NL0hxSy5ZxrBtMeKT4WZZ0BNgKXryemldg8Tuv3AEyach3BHz
eU0pIwpbnPm1JAPyrpDQ1yEf7QsD77gTPfEvilEci60R9DhvIMGAY+pt0qfME3yX
wOLp2yVBEXlRmvHk/y/+r+m4aCsmwSrikbWwmLLwAAA6JehtzFOWxTEfNpACP23V
mZyyZznsHIIE3Q==
=ARdm
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Slightly late as I had to rebase mid-week to insert a bug fix:
- A large series from Nick for 64-bit to further rework our exception
vectors, and rewrite portions of the syscall entry/exit and
interrupt return in C. The result is much easier to follow code
that is also faster in general.
- Cleanup of our ptrace code to split various parts out that had
become badly intertwined with #ifdefs over the years.
- Changes to our NUMA setup under the PowerVM hypervisor which should
hopefully avoid non-sensical topologies which can lead to warnings
from the workqueue code and other problems.
- MAINTAINERS updates to remove some of our old orphan entries and
update the status of others.
- Quite a few other small changes and fixes all over the map.
Thanks to: Abdul Haleem, afzal mohammed, Alexey Kardashevskiy, Andrew
Donnellan, Aneesh Kumar K.V, Balamuruhan S, Cédric Le Goater, Chen
Zhou, Christophe JAILLET, Christophe Leroy, Christoph Hellwig, Clement
Courbet, Daniel Axtens, David Gibson, Douglas Miller, Fabiano Rosas,
Fangrui Song, Ganesh Goudar, Gautham R. Shenoy, Greg Kroah-Hartman,
Greg Kurz, Gustavo Luiz Duarte, Hari Bathini, Ilie Halip, Jan Kara,
Joe Lawrence, Joe Perches, Kajol Jain, Larry Finger, Laurentiu Tudor,
Leonardo Bras, Libor Pechacek, Madhavan Srinivasan, Mahesh Salgaonkar,
Masahiro Yamada, Masami Hiramatsu, Mauricio Faria de Oliveira, Michael
Neuling, Michal Suchanek, Mike Rapoport, Nageswara R Sastry, Nathan
Chancellor, Nathan Lynch, Naveen N. Rao, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Po-Hsu Lin, Pratik Rajesh Sampat,
Rasmus Villemoes, Ravi Bangoria, Roman Bolshakov, Sam Bobroff,
Sandipan Das, Santosh S, Sedat Dilek, Segher Boessenkool, Shilpasri G
Bhat, Sourabh Jain, Srikar Dronamraju, Stephen Rothwell, Tyrel
Datwyler, Vaibhav Jain, YueHaibing"
* tag 'powerpc-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (158 commits)
powerpc: Make setjmp/longjmp signature standard
powerpc/cputable: Remove unnecessary copy of cpu_spec->oprofile_type
powerpc: Suppress .eh_frame generation
powerpc: Drop -fno-dwarf2-cfi-asm
powerpc/32: drop unused ISA_DMA_THRESHOLD
powerpc/powernv: Add documentation for the opal sensor_groups sysfs interfaces
selftests/powerpc: Fix try-run when source tree is not writable
powerpc/vmlinux.lds: Explicitly retain .gnu.hash
powerpc/ptrace: move ptrace_triggered() into hw_breakpoint.c
powerpc/ptrace: create ppc_gethwdinfo()
powerpc/ptrace: create ptrace_get_debugreg()
powerpc/ptrace: split out ADV_DEBUG_REGS related functions.
powerpc/ptrace: move register viewing functions out of ptrace.c
powerpc/ptrace: split out TRANSACTIONAL_MEM related functions.
powerpc/ptrace: split out SPE related functions.
powerpc/ptrace: split out ALTIVEC related functions.
powerpc/ptrace: split out VSX related functions.
powerpc/ptrace: drop PARAMETER_SAVE_AREA_OFFSET
powerpc/ptrace: drop unnecessary #ifdefs CONFIG_PPC64
powerpc/ptrace: remove unused header includes
...
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth Vijayan
common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other fixes/improvements
in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios
mm cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEE3QHqV+H2a8xAv27vjYWKoQLXFBgFAl6Ig2YACgkQjYWKoQLX
FBj2gggAibnHOl9d0ngX1mVT4nz51R3V8z5sEQjNMr2uHBmaTqs7pi/00gaFMxoC
NngVEXvL443jSogQivthGgXPpRCV9xdKE3sp38j7fF4LgHoeuDtGd1oaX4W9Rqk0
7Yii35EaO2e2WHdOKaAbu+ZvDRunFjERyntc51MYaIUivFosogSo07vC73vFIArF
VGStS09fJ4Ny76ott896T7Ulx1Iek/MkF1vponEMLGNUIcLIQbbxZxOwgz0pHuEF
SlyyJBnhOIaAJGOYlKREQDt1cew+hsxluPU+a01bwdsmdZv9LH1BGwLayDqTH58i
QWvtEpzJFmDvo9jGM1v81ebaGnyCKg==
=hiGF
-----END PGP SIGNATURE-----
Merge tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Update maintainers. Niklas Schnelle takes over zpci and Vineeth
Vijayan common io code.
- Extend cpuinfo to include topology information.
- Add new extended counters for IBM z15 and sampling buffer allocation
rework in perf code.
- Add control over zeroing out memory during system restart.
- CCA protected key block version 2 support and other
fixes/improvements in crypto code.
- Convert to new fallthrough; annotations.
- Replace zero-length arrays with flexible-arrays.
- QDIO debugfs and other small improvements.
- Drop 2-level paging support optimization for compat tasks. Varios mm
cleanups.
- Remove broken and unused hibernate / power management support.
- Remove fake numa support which does not bring any benefits.
- Exclude offline CPUs from CPU topology masks to be more consistent
with other architectures.
- Prevent last branching instruction address leaking to userspace.
- Other small various fixes and improvements all over the code.
* tag 's390-5.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (57 commits)
s390/mm: cleanup init_new_context() callback
s390/mm: cleanup virtual memory constants usage
s390/mm: remove page table downgrade support
s390/qdio: set qdio_irq->cdev at allocation time
s390/qdio: remove unused function declarations
s390/ccwgroup: remove pm support
s390/ap: remove power management code from ap bus and drivers
s390/zcrypt: use kvmalloc instead of kmalloc for 256k alloc
s390/mm: cleanup arch_get_unmapped_area() and friends
s390/ism: remove pm support
s390/cio: use fallthrough;
s390/vfio: use fallthrough;
s390/zcrypt: use fallthrough;
s390: use fallthrough;
s390/cpum_sf: Fix wrong page count in error message
s390/diag: fix display of diagnose call statistics
s390/ap: Remove ap device suspend and resume callbacks
s390/pci: Improve handling of unset UID
s390/pci: Fix zpci_alloc_domain() over allocation
s390/qdio: pass ISC as parameter to chsc_sadc()
...
-----BEGIN PGP SIGNATURE-----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=deWu
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Revert sysfs "rescan" renames that broke apps (Kelsey Skunberg)
- Add more 32 GT/s link speed decoding and improve the implementation
(Yicong Yang)
Resource management:
- Add support for sizing programmable host bridge apertures and fix a
related alpha Nautilus regression (Ivan Kokshaysky)
Interrupts:
- Add boot interrupt quirk mechanism for Xeon chipsets and document
boot interrupts (Sean V Kelley)
PCIe native device hotplug:
- When possible, disable in-band presence detect and use PDS
(Alexandru Gagniuc)
- Add DMI table for devices that don't use in-band presence detection
but don't advertise that correctly (Stuart Hayes)
- Fix hang when powering slots up/down via sysfs (Lukas Wunner)
- Fix an MSI interrupt race (Stuart Hayes)
Virtualization:
- Add ACS quirks for Zhaoxin devices (Raymond Pang)
Error handling:
- Add Error Disconnect Recover (EDR) support so firmware can report
devices disconnected via DPC and we can try to recover (Kuppuswamy
Sathyanarayanan)
Peer-to-peer DMA:
- Add Intel Sky Lake-E Root Ports B, C, D to the whitelist (Andrew
Maier)
ASPM:
- Reduce severity of common clock config message (Chris Packham)
- Clear the correct bits when enabling L1 substates, so we don't go
to the wrong state (Yicong Yang)
Endpoint framework:
- Replace EPF linkup ops with notifier call chain and improve locking
(Kishon Vijay Abraham I)
- Fix concurrent memory allocation in OB address region (Kishon Vijay
Abraham I)
- Move PF function number assignment to EPC core to support multiple
function creation methods (Kishon Vijay Abraham I)
- Fix issue with clearing configfs "start" entry (Kunihiko Hayashi)
- Fix issue with endpoint MSI-X ignoring BAR Indicator and Table
Offset (Kishon Vijay Abraham I)
- Add support for testing DMA transfers (Kishon Vijay Abraham I)
- Add support for testing > 10 endpoint devices (Kishon Vijay Abraham I)
- Add support for tests to clear IRQ (Kishon Vijay Abraham I)
- Add common DT schema for endpoint controllers (Kishon Vijay Abraham I)
Amlogic Meson PCIe controller driver:
- Add DT bindings for AXG PCIe PHY, shared MIPI/PCIe analog PHY (Remi
Pommarel)
- Add Amlogic AXG PCIe PHY, AXG MIPI/PCIe analog PHY drivers (Remi
Pommarel)
Cadence PCIe controller driver:
- Add Root Complex/Endpoint DT schema for Cadence PCIe (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Add two VMD Device IDs that require bus restriction mode (Sushma
Kalakota)
Mobiveil PCIe controller driver:
- Refactor and modularize mobiveil driver (Hou Zhiqiang)
- Add support for Mobiveil GPEX Gen4 host (Hou Zhiqiang)
Microsoft Hyper-V host bridge driver:
- Add support for Hyper-V PCI protocol version 1.3 and
PCI_BUS_RELATIONS2 (Long Li)
- Refactor to prepare for virtual PCI on non-x86 architectures (Boqun
Feng)
- Fix memory leak in hv_pci_probe()'s error path (Dexuan Cui)
NVIDIA Tegra PCIe controller driver:
- Use pci_parse_request_of_pci_ranges() (Rob Herring)
- Add support for endpoint mode and related DT updates (Vidya Sagar)
- Reduce -EPROBE_DEFER error message log level (Thierry Reding)
Qualcomm PCIe controller driver:
- Restrict class fixup to specific Qualcomm devices (Bjorn Andersson)
Synopsys DesignWare PCIe controller driver:
- Refactor core initialization code for endpoint mode (Vidya Sagar)
- Fix endpoint MSI-X to use correct table address (Kishon Vijay
Abraham I)
TI DRA7xx PCIe controller driver:
- Fix MSI IRQ handling (Vignesh Raghavendra)
TI Keystone PCIe controller driver:
- Allow AM654 endpoint to raise MSI-X interrupt (Kishon Vijay Abraham I)
Miscellaneous:
- Quirk ASMedia XHCI USB to avoid "PME# from D0" defect (Kai-Heng
Feng)
- Use ioremap(), not phys_to_virt(), for platform ROM to fix video
ROM mapping with CONFIG_HIGHMEM (Mikel Rychliski)"
* tag 'pci-v5.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (96 commits)
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
PCI: sysfs: Revert "rescan" file renames
...
- Apply Qualcomm class fixup only to PCIe host bridges, not to all
PCI_VENDOR_ID_QCOM devices (Bjorn Andersson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Fix the fixup of PCI_VENDOR_ID_QCOM
- Restructure mobiveil driver to support either Root Complex mode or
Endpoint mode (Hou Zhiqiang)
- Collect host initialization into one place (Hou Zhiqiang)
- Collect interrupt-related code into one place (Hou Zhiqiang)
- Split mobiveil into separate files under
drivers/pci/controller/mobiveil for easier reuse (Hou Zhiqiang)
- Add callbacks for interrupt initialization and linkup checking (Hou
Zhiqiang)
- Add 8- and 16-bit CSR accessors (Hou Zhiqiang)
- Initialize host driver only if Header Type is "bridge" (Hou Zhiqiang)
- Add DT bindings for NXP Layerscape SoCs PCIe Gen4 controller (Hou
Zhiqiang)
- Add PCIe Gen4 RC driver for Layerscape SoCs (Hou Zhiqiang)
- Add pcie-mobiveil __iomem annotations (Hou Zhiqiang)
- Add PCI_MSI_IRQ_DOMAIN Kconfig dependency (Hou Zhiqiang)
* remotes/lorenzo/pci/mobiveil:
PCI: mobiveil: Fix unmet dependency warning for PCIE_MOBIVEIL_PLAT
PCI: mobiveil: Fix sparse different address space warnings
PCI: mobiveil: Add PCIe Gen4 RC driver for Layerscape SoCs
dt-bindings: PCI: Add NXP Layerscape SoCs PCIe Gen4 controller
PCI: mobiveil: Add Header Type field check
PCI: mobiveil: Add 8-bit and 16-bit CSR register accessors
PCI: mobiveil: Allow mobiveil_host_init() to be used to re-init host
PCI: mobiveil: Add callback function for link up check
PCI: mobiveil: Add callback function for interrupt initialization
PCI: mobiveil: Modularize the Mobiveil PCIe Host Bridge IP driver
PCI: mobiveil: Collect the interrupt related operations into a function
PCI: mobiveil: Move the host initialization into a function
PCI: mobiveil: Introduce a new structure mobiveil_root_port
- Fix memory leak in hv probe path (Dexuan Cui)
- Add support for Hyper-V protocol 1.3 (Long Li)
- Replace zero-length array with flexible-array member (Gustavo A. R.
Silva)
- Move hypercall definitions to <asm/hyperv-tlfs.h> (Boqun Feng)
- Move retarget definitions to <asm/hyperv-tlfs.h> and make them packed
(Boqun Feng)
- Add struct hv_msi_entry and hv_set_msi_entry_from_desc() to prepare for
future virtual PCI on non-x86 (Boqun Feng)
* remotes/lorenzo/pci/hv:
PCI: hv: Introduce hv_msi_entry
PCI: hv: Move retarget related structures into tlfs header
PCI: hv: Move hypercall related definitions into tlfs header
PCI: hv: Replace zero-length array with flexible-array member
PCI: hv: Add support for protocol 1.3 and support PCI_BUS_RELATIONS2
PCI: hv: Decouple the func definition in hv_dr_state from VSP message
PCI: hv: Add missing kfree(hbus) in hv_pci_probe()'s error handling path
PCI: hv: Remove unnecessary type casting from kzalloc
- Use notification chain instead of EPF linkup ops for EPC events (Kishon
Vijay Abraham I)
- Protect concurrent allocation in endpoint outbound address region
(Kishon Vijay Abraham I)
- Protect concurrent access to pci_epf_ops (Kishon Vijay Abraham I)
- Assign function number for each PF in endpoint core (Kishon Vijay
Abraham I)
- Refactor endpoint mode core initialization (Vidya Sagar)
- Add API to notify when core initialization completes (Vidya Sagar)
- Add test framework support to defer core initialization (Vidya Sagar)
- Update Tegra SoC ABI header to support uninitialization of UPHY PLL
when in endpoint mode without reference clock (Vidya Sagar)
- Add DT and driver support for Tegra194 PCIe endpoint nodes (Vidya
Sagar)
- Add endpoint test support for DMA data transfer (Kishon Vijay
Abraham I)
- Print throughput information in endpoint test (Kishon Vijay Abraham I)
- Use streaming DMA APIs for endpoint test buffer allocation (Kishon
Vijay Abraham I)
- Add endpoint test command line option for DMA (Kishon Vijay Abraham I)
- When stopping a controller via configfs, clear endpoint "start" entry
to prevent WARN_ON (Kunihiko Hayashi)
- Update endpoint ->set_msix() to pay attention to MSI-X BAR Indicator
and offset when finding MSI-X tables (Kishon Vijay Abraham I)
- MSI-X tables are in local memory, not in the PCI address space. Update
pcie-designware-ep to account for this (Kishon Vijay Abraham I)
- Allow AM654 PCIe Endpoint to raise MSI-X interrupts (Kishon Vijay
Abraham I)
- Avoid using module parameter to determine irqtype for endpoint test
(Kishon Vijay Abraham I)
- Add ioctl to clear IRQ for endpoint test (Kishon Vijay Abraham I)
- Add endpoint test 'e' option to clear IRQ (Kishon Vijay Abraham I)
- Bump limit on number of endpoint test devices from 10 to 10,000 (Kishon
Vijay Abraham I)
- Use full pci-endpoint-test name in request_irq() for easier profiling
(Kishon Vijay Abraham I)
- Reduce log level of -EPROBE_DEFER error messages to debug (Thierry
Reding)
* remotes/lorenzo/pci/endpoint:
misc: pci_endpoint_test: remove duplicate macro PCI_ENDPOINT_TEST_STATUS
PCI: tegra: Print -EPROBE_DEFER error message at debug level
misc: pci_endpoint_test: Use full pci-endpoint-test name in request_irq()
misc: pci_endpoint_test: Fix to support > 10 pci-endpoint-test devices
tools: PCI: Add 'e' to clear IRQ
misc: pci_endpoint_test: Add ioctl to clear IRQ
misc: pci_endpoint_test: Avoid using module parameter to determine irqtype
PCI: keystone: Allow AM654 PCIe Endpoint to raise MSI-X interrupt
PCI: dwc: Fix dw_pcie_ep_raise_msix_irq() to get correct MSI-X table address
PCI: endpoint: Fix ->set_msix() to take BIR and offset as arguments
misc: pci_endpoint_test: Add support to get DMA option from userspace
tools: PCI: Add 'd' command line option to support DMA
misc: pci_endpoint_test: Use streaming DMA APIs for buffer allocation
PCI: endpoint: functions/pci-epf-test: Print throughput information
PCI: endpoint: functions/pci-epf-test: Add DMA support to transfer data
PCI: endpoint: Fix clearing start entry in configfs
PCI: tegra: Add support for PCIe endpoint mode in Tegra194
dt-bindings: PCI: tegra: Add DT support for PCIe EP nodes in Tegra194
soc/tegra: bpmp: Update ABI header
PCI: pci-epf-test: Add support to defer core initialization
PCI: dwc: Add API to notify core initialization completion
PCI: endpoint: Add notification for core init completion
PCI: dwc: Refactor core initialization code for EP mode
PCI: endpoint: Add core init notifying feature
PCI: endpoint: Assign function number for each PF in EPC core
PCI: endpoint: Protect concurrent access to pci_epf_ops with mutex
PCI: endpoint: Fix for concurrent memory allocation in OB address region
PCI: endpoint: Replace spinlock with mutex
PCI: endpoint: Use notification chain mechanism to notify EPC events to EPF
- Use ioremap(), not phys_to_virt() for platform ROM, to fix video ROM
mapping with CONFIG_HIGHMEM (Mikel Rychliski)
- Add support for root bus sizing so we don't have to assume host bridge
windows are known a priori (Ivan Kokshaysky)
- Fix alpha Nautilus PCI setup, which has been broken since we started
enforcing window limits in resource allocation (Ivan Kokshaysky)
* pci/resource:
alpha: Fix nautilus PCI setup
PCI: Add support for root bus sizing
PCI: Use ioremap(), not phys_to_virt() for platform ROM
- Move _HPX type array from stack to static data (Colin Ian King)
- Avoid an ASMedia XHCI USB PME# defect; apparently it doesn't assert
PME# when USB3.0 devices are hotplugged in D0 (Kai-Heng Feng)
- Revert sysfs "rescan" file renames that broke an application (Kelsey
Skunberg)
* pci/misc:
PCI: sysfs: Revert "rescan" file renames
PCI: Avoid ASMedia XHCI USB PME# from D0 defect
PCI/ACPI: Move pcie_to_hpx3_type[] from stack to static data
- Disable in-band presence detection when possible (Alexandru Gagniuc)
- Poll for presence detect if in-band presence detection is disabled
(Alexandru Gagniuc)
- Add DMI table of systems that don't support in-band presence detection
(Stuart Hayes)
- Fix indefinite pciehp wait caused by race in handling sysfs requests
(Lukas Wunner)
- Fix pciehp MSI interrupt race that caused us to miss interrupts (Stuart
Hayes)
* pci/hotplug:
PCI: pciehp: Fix MSI interrupt race
PCI: pciehp: Fix indefinite wait on sysfs requests
PCI: pciehp: Add DMI table for in-band presence detection disabled
PCI: pciehp: Wait for PDS if in-band presence is disabled
PCI: pciehp: Disable in-band presence detect when possible
- Update error status after reset_link() so we don't report "recovery
failed" when it in fact succeeded (Kuppuswamy Sathyanarayanan)
- Move DPC data into struct pci_dev instead of allocating a separate
struct dpc_dev (Bjorn Helgaas)
- Remove AER/DPC service dependency to simplify error recovery
(Kuppuswamy Sathyanarayanan)
- Return error recovery status for future use by EDR, which needs to tell
firmware whether recovery was successful (Kuppuswamy Sathyanarayanan)
- Cache DPC capability info in core since it's needed by EDR as well as
DPC driver (Kuppuswamy Sathyanarayanan)
- Add pci_aer_raw_clear_status() to allow EDR recovery path to clear AER
status even when OS doesn't own the AER capability (Kuppuswamy
Sathyanarayanan)
- Add Error Disconnect Recover (EDR) support, so firmware can use ACPI
notification to tell the OS that devices have been disconnected, e.g.,
via DPC, and that OS should attempt recovery (Kuppuswamy
Sathyanarayanan)
- Rename AER error status clearing interfaces to be more consistent
(Kuppuswamy Sathyanarayanan)
* pci/edr:
PCI/AER: Rationalize error status register clearing
PCI/DPC: Add Error Disconnect Recover (EDR) support
PCI/DPC: Expose dpc_process_error(), dpc_reset_link() for use by EDR
PCI/AER: Add pci_aer_raw_clear_status() to unconditionally clear Error Status
PCI/DPC: Cache DPC capabilities in pci_init_capabilities()
PCI/ERR: Return status of pcie_do_recovery()
PCI/ERR: Remove service dependency in pcie_do_recovery()
PCI/DPC: Move DPC data into struct pci_dev
PCI/ERR: Update error status after reset_link()
PCI/ERR: Combine pci_channel_io_frozen cases
Probe deferral is an expected error condition that will usually be
recovered from. Print such error messages at debug level to make them
available for diagnostic purposes when building with debugging enabled
and hide them otherwise to not spam the kernel log with them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
AM654 PCIe EP controller has MSI-X capability register and has the
ability to raise MSI-X interrupt. Add support in pci-keystone.c
for PCIe endpoint controller in AM654 to raise MSI-X interrupts.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler"),
in order to raise MSI-X interrupt, obtained MSIX table address from
Base Address Register (BAR). However BAR only holds PCI address
programmed by the host whereas the MSI-X table should be in the local
memory.
Store the MSI-X table address (virtual address) as part of ->set_bar()
callback and use that to get the message address and message data
here.
Fixes: beb4641a78 ("PCI: dwc: Add MSI-X callbacks handler")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
commit 8963106eab ("PCI: endpoint: Add MSI-X interfaces") while
adding support to raise MSI-X interrupts from endpoint didn't include
BAR Indicator register (BIR) configuration and MSI-X table offset as
arguments in pci_epc_set_msix(). This would result in endpoint
controller register using random BAR indicator register, the memory
for which might not be allocated by the endpoint function driver.
Add BAR indicator register and MSI-X table offset as arguments in
pci_epc_set_msix() and allocate space for MSI-X table and pending
bit array (PBA) in pci-epf-test endpoint function driver.
Fixes: 8963106eab ("PCI: endpoint: Add MSI-X interfaces")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Print throughput information in KB/s after every completed transfer,
including information on whether DMA is used or not.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Alan Mikhak <alan.mikhak@sifive.com>
Use dmaengine API and add support for transferring data using DMA.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Alan Mikhak <alan.mikhak@sifive.com>
Pull networking updates from David Miller:
"Highlights:
1) Fix the iwlwifi regression, from Johannes Berg.
2) Support BSS coloring and 802.11 encapsulation offloading in
hardware, from John Crispin.
3) Fix some potential Spectre issues in qtnfmac, from Sergey
Matyukevich.
4) Add TTL decrement action to openvswitch, from Matteo Croce.
5) Allow paralleization through flow_action setup by not taking the
RTNL mutex, from Vlad Buslov.
6) A lot of zero-length array to flexible-array conversions, from
Gustavo A. R. Silva.
7) Align XDP statistics names across several drivers for consistency,
from Lorenzo Bianconi.
8) Add various pieces of infrastructure for offloading conntrack, and
make use of it in mlx5 driver, from Paul Blakey.
9) Allow using listening sockets in BPF sockmap, from Jakub Sitnicki.
10) Lots of parallelization improvements during configuration changes
in mlxsw driver, from Ido Schimmel.
11) Add support to devlink for generic packet traps, which report
packets dropped during ACL processing. And use them in mlxsw
driver. From Jiri Pirko.
12) Support bcmgenet on ACPI, from Jeremy Linton.
13) Make BPF compatible with RT, from Thomas Gleixnet, Alexei
Starovoitov, and your's truly.
14) Support XDP meta-data in virtio_net, from Yuya Kusakabe.
15) Fix sysfs permissions when network devices change namespaces, from
Christian Brauner.
16) Add a flags element to ethtool_ops so that drivers can more simply
indicate which coalescing parameters they actually support, and
therefore the generic layer can validate the user's ethtool
request. Use this in all drivers, from Jakub Kicinski.
17) Offload FIFO qdisc in mlxsw, from Petr Machata.
18) Support UDP sockets in sockmap, from Lorenz Bauer.
19) Fix stretch ACK bugs in several TCP congestion control modules,
from Pengcheng Yang.
20) Support virtual functiosn in octeontx2 driver, from Tomasz
Duszynski.
21) Add region operations for devlink and use it in ice driver to dump
NVM contents, from Jacob Keller.
22) Add support for hw offload of MACSEC, from Antoine Tenart.
23) Add support for BPF programs that can be attached to LSM hooks,
from KP Singh.
24) Support for multiple paths, path managers, and counters in MPTCP.
From Peter Krystad, Paolo Abeni, Florian Westphal, Davide Caratti,
and others.
25) More progress on adding the netlink interface to ethtool, from
Michal Kubecek"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2121 commits)
net: ipv6: rpl_iptunnel: Fix potential memory leak in rpl_do_srh_inline
cxgb4/chcr: nic-tls stats in ethtool
net: dsa: fix oops while probing Marvell DSA switches
net/bpfilter: remove superfluous testing message
net: macb: Fix handling of fixed-link node
net: dsa: ksz: Select KSZ protocol tag
netdevsim: dev: Fix memory leak in nsim_dev_take_snapshot_write
net: stmmac: add EHL 2.5Gbps PCI info and PCI ID
net: stmmac: add EHL PSE0 & PSE1 1Gbps PCI info and PCI ID
net: stmmac: create dwmac-intel.c to contain all Intel platform
net: dsa: bcm_sf2: Support specifying VLAN tag egress rule
net: dsa: bcm_sf2: Add support for matching VLAN TCI
net: dsa: bcm_sf2: Move writing of CFP_DATA(5) into slicing functions
net: dsa: bcm_sf2: Check earlier for FLOW_EXT and FLOW_MAC_EXT
net: dsa: bcm_sf2: Disable learning for ASP port
net: dsa: b53: Deny enslaving port 7 for 7278 into a bridge
net: dsa: b53: Prevent tagged VLAN on port 7 for 7278
net: dsa: b53: Restore VLAN entries upon (re)configuration
net: dsa: bcm_sf2: Fix overflow checks
hv_netvsc: Remove unnecessary round_up for recv_completion_cnt
...
Without this commit, a PCIe hotplug port can stop generating interrupts on
hotplug events, so device adds and removals will not be seen:
The pciehp interrupt handler pciehp_isr() reads the Slot Status register
and then writes back to it to clear the bits that caused the interrupt. If
a different interrupt event bit gets set between the read and the write,
pciehp_isr() returns without having cleared all of the interrupt event
bits. If this happens when the MSI isn't masked (which by default it isn't
in handle_edge_irq(), and which it will never be when MSI per-vector
masking is not supported), we won't get any more hotplug interrupts from
that device.
That is expected behavior, according to the PCIe Base Spec r5.0, section
6.7.3.4, "Software Notification of Hot-Plug Events".
Because the Presence Detect Changed and Data Link Layer State Changed event
bits can both get set at nearly the same time when a device is added or
removed, this is more likely to happen than it might seem. The issue was
found (and can be reproduced rather easily) by connecting and disconnecting
an NVMe storage device on at least one system model where the NVMe devices
were being connected to an AMD PCIe port (PCI device 0x1022/0x1483).
Fix the issue by modifying pciehp_isr() to loop back and re-read the Slot
Status register immediately after writing to it, until it sees that all of
the event status bits have been cleared.
[lukas: drop loop count limitation, write "events" instead of "status",
don't loop back in INTx and poll modes, tweak code comment & commit msg]
Link: https://lore.kernel.org/r/78b4ced5072bfe6e369d20e8b47c279b8c7af12e.1582121613.git.lukas@wunner.de
Tested-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Joerg Roedel <jroedel@suse.de>
David Hoyer reports that powering pciehp slots up or down via sysfs may
hang: The call to wait_event() in pciehp_sysfs_enable_slot() and
_disable_slot() does not return because ctrl->ist_running remains true.
This flag, which was introduced by commit 157c1062fc ("PCI: pciehp: Avoid
returning prematurely from sysfs requests"), signifies that the IRQ thread
pciehp_ist() is running. It is set to true at the top of pciehp_ist() and
reset to false at the end. However there are two additional return
statements in pciehp_ist() before which the commit neglected to reset the
flag to false and wake up waiters for the flag.
That omission opens up the following race when powering up the slot:
* pciehp_ist() runs because a PCI_EXP_SLTSTA_PDC event was requested
by pciehp_sysfs_enable_slot()
* pciehp_ist() turns on slot power via the following call stack:
pciehp_handle_presence_or_link_change() -> pciehp_enable_slot() ->
__pciehp_enable_slot() -> board_added() -> pciehp_power_on_slot()
* after slot power is turned on, the link comes up, resulting in a
PCI_EXP_SLTSTA_DLLSC event
* the IRQ handler pciehp_isr() stores the event in ctrl->pending_events
and returns IRQ_WAKE_THREAD
* the IRQ thread is already woken (it's bringing up the slot), but the
genirq code remembers to re-run the IRQ thread after it has finished
(such that it can deal with the new event) by setting IRQTF_RUNTHREAD
via __handle_irq_event_percpu() -> __irq_wake_thread()
* the IRQ thread removes PCI_EXP_SLTSTA_DLLSC from ctrl->pending_events
via board_added() -> pciehp_check_link_status() in order to deal with
presence and link flaps per commit 6c35a1ac3d ("PCI: pciehp:
Tolerate initially unstable link")
* after pciehp_ist() has successfully brought up the slot, it resets
ctrl->ist_running to false and wakes up the sysfs requester
* the genirq code re-runs pciehp_ist(), which sets ctrl->ist_running
to true but then returns with IRQ_NONE because ctrl->pending_events
is empty
* pciehp_sysfs_enable_slot() is finally woken but notices that
ctrl->ist_running is true, hence continues waiting
The only way to get the hung task going again is to trigger a hotplug
event which brings down the slot, e.g. by yanking out the card.
The same race exists when powering down the slot because remove_board()
likewise clears link or presence changes in ctrl->pending_events per commit
3943af9d01 ("PCI: pciehp: Ignore Link State Changes after powering off a
slot") and thereby may cause a re-run of pciehp_ist() which returns with
IRQ_NONE without resetting ctrl->ist_running to false.
Fix by adding a goto label before the teardown steps at the end of
pciehp_ist() and jumping to that label from the two return statements which
currently neglect to reset the ctrl->ist_running flag.
Fixes: 157c1062fc ("PCI: pciehp: Avoid returning prematurely from sysfs requests")
Link: https://lore.kernel.org/r/cca1effa488065cb055120aa01b65719094bdcb5.1584530321.git.lukas@wunner.de
Reported-by: David Hoyer <David.Hoyer@netapp.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Cc: stable@vger.kernel.org # v4.19+
After an endpoint is started through configfs, if 0 is written to the
configfs entry 'start', the controller stops but the epc_group->start
value remains 1.
A subsequent unlinking of the function from the controller would trigger
a spurious WARN_ON_ONCE() in pci_epc_epf_unlink() despite right
behavior.
Fix it by setting epc_group->start = 0 when a controller is stopped
using configfs.
Fixes: d746799116 ("PCI: endpoint: Introduce configfs entry for configuring EP functions")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Add support for the endpoint mode of Synopsys DesignWare core based
dual mode PCIe controllers present in Tegra194 SoC.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early. Most cleanup changes come
through the various maintainer trees, so the final removal of
setup_irq() is postponed towards the end of the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and unsafe
interrupt injection including a fixup of the offending PCI/AER error
injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside of
an actual interrupt, can cause inconsistent state on the fragile
x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=DZ/G
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Treewide:
- Cleanup of setup_irq() which is not longer required because the
memory allocator is available early.
Most cleanup changes come through the various maintainer trees, so
the final removal of setup_irq() is postponed towards the end of
the merge window.
Core:
- Protection against unsafe invocation of interrupt handlers and
unsafe interrupt injection including a fixup of the offending
PCI/AER error injection mechanism.
Invoking interrupt handlers from arbitrary contexts, i.e. outside
of an actual interrupt, can cause inconsistent state on the
fragile x86 interrupt affinity changing hardware trainwreck.
Drivers:
- Second wave of support for the new ARM GICv4.1
- Multi-instance support for Xilinx and PLIC interrupt controllers
- CPU-Hotplug support for PLIC
- The obligatory new driver for X1000 TCU
- Enhancements, cleanups and fixes all over the place"
* tag 'irq-core-2020-03-30' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (58 commits)
unicore32: Replace setup_irq() by request_irq()
sh: Replace setup_irq() by request_irq()
hexagon: Replace setup_irq() by request_irq()
c6x: Replace setup_irq() by request_irq()
alpha: Replace setup_irq() by request_irq()
irqchip/gic-v4.1: Eagerly vmap vPEs
irqchip/gic-v4.1: Add VSGI property setup
irqchip/gic-v4.1: Add VSGI allocation/teardown
irqchip/gic-v4.1: Move doorbell management to the GICv4 abstraction layer
irqchip/gic-v4.1: Plumb set_vcpu_affinity SGI callbacks
irqchip/gic-v4.1: Plumb get/set_irqchip_state SGI callbacks
irqchip/gic-v4.1: Plumb mask/unmask SGI callbacks
irqchip/gic-v4.1: Add initial SGI configuration
irqchip/gic-v4.1: Plumb skeletal VSGI irqchip
irqchip/stm32: Retrigger both in eoi and unmask callbacks
irqchip/gic-v3: Move irq_domain_update_bus_token to after checking for NULL domain
irqchip/xilinx: Do not call irq_set_default_host()
irqchip/xilinx: Enable generic irq multi handler
irqchip/xilinx: Fill error code when irq domain registration fails
irqchip/xilinx: Add support for multiple instances
...
Pull perf updates from Ingo Molnar:
"The main changes in this cycle were:
Kernel side changes:
- A couple of x86/cpu cleanups and changes were grandfathered in due
to patch dependencies. These clean up the set of CPU model/family
matching macros with a consistent namespace and C99 initializer
style.
- A bunch of updates to various low level PMU drivers:
* AMD Family 19h L3 uncore PMU
* Intel Tiger Lake uncore support
* misc fixes to LBR TOS sampling
- optprobe fixes
- perf/cgroup: optimize cgroup event sched-in processing
- misc cleanups and fixes
Tooling side changes are to:
- perf {annotate,expr,record,report,stat,test}
- perl scripting
- libapi, libperf and libtraceevent
- vendor events on Intel and S390, ARM cs-etm
- Intel PT updates
- Documentation changes and updates to core facilities
- misc cleanups, fixes and other enhancements"
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (89 commits)
cpufreq/intel_pstate: Fix wrong macro conversion
x86/cpu: Cleanup the now unused CPU match macros
hwrng: via_rng: Convert to new X86 CPU match macros
crypto: Convert to new CPU match macros
ASoC: Intel: Convert to new X86 CPU match macros
powercap/intel_rapl: Convert to new X86 CPU match macros
PCI: intel-mid: Convert to new X86 CPU match macros
mmc: sdhci-acpi: Convert to new X86 CPU match macros
intel_idle: Convert to new X86 CPU match macros
extcon: axp288: Convert to new X86 CPU match macros
thermal: Convert to new X86 CPU match macros
hwmon: Convert to new X86 CPU match macros
platform/x86: Convert to new CPU match macros
EDAC: Convert to new X86 CPU match macros
cpufreq: Convert to new X86 CPU match macros
ACPI: Convert to new X86 CPU match macros
x86/platform: Convert to new CPU match macros
x86/kernel: Convert to new CPU match macros
x86/kvm: Convert to new CPU match macros
x86/perf/events: Convert to new CPU match macros
...
We changed these sysfs filenames:
.../pci_bus/<domain:bus>/rescan -> .../pci_bus/<domain:bus>/bus_rescan
.../<domain🚌dev.fn>/rescan -> .../<domain🚌dev.fn>/dev_rescan
and Ruslan reported [1] that this broke a userspace application.
Revert these name changes so both files are named "rescan" again.
Note that we have to use __ATTR() to assign custom C symbols, i.e.,
"struct device_attribute <symbol>".
[1] https://lore.kernel.org/r/CAB=otbSYozS-ZfxB0nCiNnxcbqxwrHOSYxJJtDKa63KzXbXgpw@mail.gmail.com
[bhelgaas: commit log, use __ATTR() both places so we don't have to rename
the attributes]
Fixes: 8bdfa145f5 ("PCI: sysfs: Define device attributes with DEVICE_ATTR*()")
Fixes: 4e2b79436e ("PCI: sysfs: Change DEVICE_ATTR() to DEVICE_ATTR_WO()")
Link: https://lore.kernel.org/r/20200325151708.32612-1-skunberg.kelsey@gmail.com
Signed-off-by: Kelsey Skunberg <kelsey.skunberg@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org # v5.4+
In certain cases we should be able to enumerate IO and MEM ranges of all
PCI devices installed in the system, and then set respective host bridge
apertures basing on calculated size and alignment. Particularly when
firmware is broken and fails to assign bridge windows properly, like on
Alpha UP1500 platform.
Actually, almost everything is already in place, and required changes are
minimal:
- add "size_windows" flag to struct pci_host_bridge: when set, it
instructs __pci_bus_size_bridges() to continue with the root bus;
- in the __pci_bus_size_bridges() path: add checks for bus->self,
as it can legitimately be null for the root bus.
Link: https://lore.kernel.org/r/20200314194355.GA12510@mail.rc.ru
Tested-by: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
On some EFI systems, the video BIOS is provided by the EFI firmware. The
boot stub code stores the physical address of the ROM image in pdev->rom.
Currently we attempt to access this pointer using phys_to_virt(), which
doesn't work with CONFIG_HIGHMEM.
On these systems, attempting to load the radeon module on a x86_32 kernel
can result in the following:
BUG: unable to handle page fault for address: 3e8ed03c
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
*pde = 00000000
Oops: 0000 [#1] PREEMPT SMP
CPU: 0 PID: 317 Comm: systemd-udevd Not tainted 5.6.0-rc3-next-20200228 #2
Hardware name: Apple Computer, Inc. MacPro1,1/Mac-F4208DC8, BIOS MP11.88Z.005C.B08.0707021221 07/02/07
EIP: radeon_get_bios+0x5ed/0xe50 [radeon]
Code: 00 00 84 c0 0f 85 12 fd ff ff c7 87 64 01 00 00 00 00 00 00 8b 47 08 8b 55 b0 e8 1e 83 e1 d6 85 c0 74 1a 8b 55 c0 85 d2 74 13 <80> 38 55 75 0e 80 78 01 aa 0f 84 a4 03 00 00 8d 74 26 00 68 dc 06
EAX: 3e8ed03c EBX: 00000000 ECX: 3e8ed03c EDX: 00010000
ESI: 00040000 EDI: eec04000 EBP: eef3fc60 ESP: eef3fbe0
DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 EFLAGS: 00010206
CR0: 80050033 CR2: 3e8ed03c CR3: 2ec77000 CR4: 000006d0
Call Trace:
r520_init+0x26/0x240 [radeon]
radeon_device_init+0x533/0xa50 [radeon]
radeon_driver_load_kms+0x80/0x220 [radeon]
drm_dev_register+0xa7/0x180 [drm]
radeon_pci_probe+0x10f/0x1a0 [radeon]
pci_device_probe+0xd4/0x140
Fix the issue by updating all drivers which can access a platform provided
ROM. Instead of calling the helper function pci_platform_rom() which uses
phys_to_virt(), call ioremap() directly on the pdev->rom.
radeon_read_platform_bios() previously directly accessed an __iomem
pointer. Avoid this by calling memcpy_fromio() instead of kmemdup().
pci_platform_rom() now has no remaining callers, so remove it.
Link: https://lore.kernel.org/r/20200319021623.5426-1-mikel@mikelr.com
Signed-off-by: Mikel Rychliski <mikel@mikelr.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Many Zhaoxin Root Ports and Switch Downstream Ports do provide ACS-like
capability but have no ACS Capability Structure. Peer-to-Peer transactions
could be blocked between these ports, so add quirk so devices behind them
could be assigned to different IOMMU group.
Link: https://lore.kernel.org/r/20200327091148.5190-4-RaymondPang-oc@zhaoxin.com
Signed-off-by: Raymond Pang <RaymondPang-oc@zhaoxin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some Zhaoxin endpoints are implemented as multi-function devices without an
ACS capability, but they actually don't support peer-to-peer transactions.
Add ACS quirks to declare DMA isolation.
Link: https://lore.kernel.org/r/20200327091148.5190-3-RaymondPang-oc@zhaoxin.com
Signed-off-by: Raymond Pang <RaymondPang-oc@zhaoxin.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When the UEFI/BIOS or bootloader has not initialised a PCIe device we would
get the following message:
kern.warning: pci 0000:00:01.0: ASPM: current common clock configuration is broken, reconfiguring
"warning" and "broken" are slightly misleading. On an embedded system it is
quite possible for the bootloader to avoid configuring PCIe devices if they
are not needed.
Downgrade the message to pci_info() and change "broken" to "inconsistent"
since we fix up the inconsistency in the code immediately following the
message (and emit an error if that fails).
Link: https://lore.kernel.org/r/20200323035530.11569-1-chris.packham@alliedtelesis.co.nz
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The AER interfaces to clear error status registers were a confusing mess:
- pci_cleanup_aer_uncorrect_error_status() cleared non-fatal errors
from the Uncorrectable Error Status register.
- pci_aer_clear_fatal_status() cleared fatal errors from the
Uncorrectable Error Status register.
- pci_cleanup_aer_error_status_regs() cleared the Root Error Status
register (for Root Ports), the Uncorrectable Error Status register,
and the Correctable Error Status register.
Rename them to make them consistent:
From To
---------------------------------------- -------------------------------
pci_cleanup_aer_uncorrect_error_status() pci_aer_clear_nonfatal_status()
pci_aer_clear_fatal_status() pci_aer_clear_fatal_status()
pci_cleanup_aer_error_status_regs() pci_aer_clear_status()
Since pci_cleanup_aer_error_status_regs() (renamed to
pci_aer_clear_status()) is only used within drivers/pci/, move the
declaration from <linux/aer.h> to drivers/pci/pci.h.
[bhelgaas: commit log, add renames]
Link: https://lore.kernel.org/r/d1310a75dc3d28f7e8da4e99c45fbd3e60fe238e.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Error Disconnect Recover (EDR) is a feature that allows ACPI firmware to
notify OSPM that a device has been disconnected due to an error condition
(ACPI v6.3, sec 5.6.6). OSPM advertises its support for EDR on PCI devices
via _OSC (see [1], sec 4.5.1, table 4-4). The OSPM EDR notify handler
should invalidate software state associated with disconnected devices and
may attempt to recover them. OSPM communicates the status of recovery to
the firmware via _OST (sec 6.3.5.2).
For PCIe, firmware may use Downstream Port Containment (DPC) to support
EDR. Per [1], sec 4.5.1, table 4-6, even if firmware has retained control
of DPC, OSPM may read/write DPC control and status registers during the EDR
notification processing window, i.e., from the time it receives an EDR
notification until it clears the DPC Trigger Status.
Note that per [1], sec 4.5.1 and 4.5.2.4,
1. If the OS supports EDR, it should advertise that to firmware by
setting OSC_PCI_EDR_SUPPORT in _OSC Support.
2. If the OS sets OSC_PCI_EXPRESS_DPC_CONTROL in _OSC Control to request
control of the DPC capability, it must also set OSC_PCI_EDR_SUPPORT in
_OSC Support.
Add an EDR notify handler to attempt recovery.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
[bhelgaas: squash add/enable patches into one]
Link: https://lore.kernel.org/r/90f91fe6d25c13f9d2255d2ce97ca15be307e1bb.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Len Brown <lenb@kernel.org>
If firmware controls DPC, it is generally responsible for managing the DPC
capability and events, and the OS should not access the DPC capability.
However, if firmware controls DPC and both the OS and the platform support
Error Disconnect Recover (EDR) notifications, the OS EDR notify handler is
responsible for recovery, and the notify handler may read/write the DPC
capability until it clears the DPC Trigger Status bit. See [1], sec 4.5.1,
table 4-6.
Expose some DPC error handling functions so they can be used by the EDR
notify handler.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/e9000bb15b3a4293e81d98bb29ead7c84a6393c9.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Per the SFI _OSC and DPC Updates ECN [1] implementation note flowchart, the
OS seems to be expected to clear AER status even if it doesn't have
ownership of the AER capability. Unlike the DPC capability, where a DPC
ECN [2] specifies a window when the OS is allowed to access DPC registers
even if it doesn't have ownership, there is no clear model for AER.
Add pci_aer_raw_clear_status() to clear the AER error status registers
unconditionally. This is intended for use only by the EDR path (see [2]).
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[2] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
[bhelgaas: changelog]
Link: https://lore.kernel.org/r/c19ad28f3633cce67448609e89a75635da0da07d.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
As per the DPC Enhancements ECN [1], sec 4.5.1, table 4-4, if the OS
supports Error Disconnect Recover (EDR), it must invalidate the software
state associated with child devices of the port without attempting to
access the child device hardware. In addition, if the OS supports DPC, it
must attempt to recover the child devices if the port implements the DPC
Capability. If the OS continues operation, the OS must inform the firmware
of the status of the recovery operation via the _OST method.
Return the result of pcie_do_recovery() so we can report it to firmware via
_OST.
[1] Downstream Port Containment Related Enhancements ECN, Jan 28, 2019,
affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/12888
Link: https://lore.kernel.org/r/eb60ec89448769349c6722954ffbf2de163155b5.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously we passed the PCIe service type parameter to pcie_do_recovery(),
where reset_link() looked up the underlying pci_port_service_driver and its
.reset_link() function pointer. Instead of using this roundabout way, we
can just pass the driver-specific .reset_link() callback function when
calling pcie_do_recovery() function.
This allows us to call pcie_do_recovery() from code that is not a PCIe port
service driver, e.g., Error Disconnect Recover (EDR) support.
Remove pcie_port_find_service() and pcie_port_service_driver.reset_link
since they are now unused.
Link: https://lore.kernel.org/r/60e02b87b526cdf2930400059d98704bf0a147d1.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Commit bdb5ac8577 ("PCI/ERR: Handle fatal error recovery") uses
reset_link() to recover from fatal errors. But during fatal error
recovery, if the initial value of error status is PCI_ERS_RESULT_DISCONNECT
or PCI_ERS_RESULT_NO_AER_DRIVER then even after successful recovery (using
reset_link()) pcie_do_recovery() will report the recovery result as
failure. Update the status of error after reset_link().
You can reproduce this issue by triggering a SW DPC using "DPC Software
Trigger" bit in "DPC Control Register". You should see recovery failed
dmesg log as below:
pcieport 0000:00:16.0: DPC: containment event, status:0x1f27 source:0x0000
pcieport 0000:00:16.0: DPC: software trigger detected
pci 0000:04:00.0: AER: can't recover (no error_detected callback)
pcieport 0000:00:16.0: AER: device recovery failed
Fixes: bdb5ac8577 ("PCI/ERR: Handle fatal error recovery")
Link: https://lore.kernel.org/r/a255fcb3a3fdebcd90f84e08b555f1786eb8eba2.1585000084.git.sathyanarayanan.kuppuswamy@linux.intel.com
[bhelgaas: split pci_channel_io_frozen simplification to separate patch]
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Keith Busch <keith.busch@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Due to an issue with PCIe wrapper logic built for the DWC PCIe IP on
dra7xx, the driver needs to ensure that there are no pending MSI IRQ
vector set (i.e PCIE_MSI_INTR0_STATUS reads 0 at least once) before
exiting IRQ handler otherwise the dra7xx PCIe wrapper will not register
new MSI IRQs even though PCIE_MSI_INTR0_STATUS reports IRQs are pending.
Therefore it's no longer possible to use default IRQ handler provided by
DWC library.
Add an irqchip implementation inside pci-dra7xx.c and install new MSI
IRQ handler to handle the above errata.
This fixes a bug, where PCIe wifi cards with 4 DMA queues like Intel
8260 used to throw following error and stall during ping/iperf3 tests.
[ 97.776310] iwlwifi 0000:01:00.0: Queue 9 stuck for 2500 ms.
Tested-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
The eeh_ops->probe() function is called from two different contexts:
1. On pseries, where we set EEH_PROBE_MODE_DEVTREE, it's called in
eeh_add_device_early() which is supposed to run before we create
a pci_dev.
2. On PowerNV, where we set EEH_PROBE_MODE_DEV, it's called in
eeh_device_add_late() which is supposed to run *after* the
pci_dev is created.
The "early" probe is required because PAPR requires that we perform an RTAS
call to enable EEH support on a device before we start interacting with it
via config space or MMIO. This requirement doesn't exist on PowerNV and
shoehorning two completely separate initialisation paths into a common
interface just results in a convoluted code everywhere.
Additionally the early probe requires the probe function to take an pci_dn
rather than a pci_dev argument. We'd like to make pci_dn a pseries specific
data structure since there's no real requirement for them on PowerNV. To
help both goals move the early probe into the pseries containment zone
so the platform depedence is more explicit.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-5-oohall@gmail.com
The pci hotplug helper (pci_hp_add_devices()) calls
eeh_add_device_tree_early() to scan the device-tree for new PCI devices and
do the early EEH probe before the device is scanned. This early probe is a
no-op in a lot of cases because:
a) The early init is only required to satisfy a PAPR requirement that EEH
be configured before we start doing config accesses. On PowerNV it is
a no-op.
b) It's a no-op for devices that have already had their eeh_dev
initialised.
There are four callers of pci_hp_add_devices():
1. arch/powerpc/kernel/eeh_driver.c
Here the hotplug helper is called when re-scanning pci_devs that
were removed during an EEH recovery pass. The EEH stat for each
removed device (the eeh_dev) is retained across a recovery pass
so the early init is a no-op in this case.
2. drivers/pci/hotplug/pnv_php.c
This is also a no-op since the PowerNV hotplug driver is, suprisingly,
PowerNV specific.
3. drivers/pci/hotplug/rpaphp_core.c
4. drivers/pci/hotplug/rpaphp_pci.c
In these two cases new devices have been hotplugged and FW has
provided new DT nodes for each. These are the only two cases where
the EEH we might have new PCI device nodes in the DT so these are
the only two cases where the early EEH probe needs to be done.
We can move the calls to eeh_add_device_tree_early() to the locations where
it's needed and remove it from the generic path. This is preparation for
making the early EEH probe pseries specific.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-3-oohall@gmail.com
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/pci/hotplug/rpaphp_core.c: In function is_php_type:
drivers/pci/hotplug/rpaphp_core.c:291:16: warning:
variable value set but not used [-Wunused-but-set-variable]
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200312140412.32373-1-chenzhou10@huawei.com
The new macro set has a consistent namespace and uses C99 initializers
instead of the grufty C89 ones.
Get rid the of the local macro wrappers for consistency.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lkml.kernel.org/r/20200320131510.393113444@linutronix.de
The poll callback is using the completion wait queue and sticks it into
poll_wait() to wake up pollers after a command has completed.
This works to some extent, but cannot provide EPOLLEXCLUSIVE support
because the waker side uses complete_all() which unconditionally wakes up
all waiters. complete_all() is required because completions internally use
exclusive wait and complete() only wakes up one waiter by default.
This mixes conceptually different mechanisms and relies on internal
implementation details of completions, which in turn puts contraints on
changing the internal implementation of completions.
Replace it with a regular wait queue and store the state in struct
switchtec_user.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20200321113240.936097534@linutronix.de
The call to init_completion() in mrpc_queue_cmd() can theoretically
race with the call to poll_wait() in switchtec_dev_poll().
poll() write()
switchtec_dev_poll() switchtec_dev_write()
poll_wait(&s->comp.wait); mrpc_queue_cmd()
init_completion(&s->comp)
init_waitqueue_head(&s->comp.wait)
To my knowledge, no one has hit this bug.
Fix this by using reinit_completion() instead of init_completion() in
mrpc_queue_cmd().
Fixes: 080b47def5 ("MicroSemi Switchtec management interface driver")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lkml.kernel.org/r/20200313183608.2646-1-logang@deltatee.com
The ASMedia USB XHCI Controller claims to support generating PME# while
in D0:
01:00.0 USB controller: ASMedia Technology Inc. Device 2142 (prog-if 30 [XHCI])
Subsystem: SUNIX Co., Ltd. Device 312b
Capabilities: [78] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable+ DSel=0 DScale=0 PME-
However PME# only gets asserted when plugging USB 2.0 or USB 1.1 devices,
but not for USB 3.0 devices.
Remove PCI_PM_CAP_PME_D0 to avoid using PME under D0.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=205919
Link: https://lore.kernel.org/r/20191219192006.16270-1-kai.heng.feng@canonical.com
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add the three remaining Intel Sky Lake-E host Root Ports to the whitelist
of p2pdma.
P2P has been tested and is working on this system.
Link: https://lore.kernel.org/r/20200207221219.4309-1-andrew.maier@eideticom.com
Signed-off-by: Andrew Maier <andrew.maier@eideticom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
In pcie_config_aspm_l1ss(), we cleared the wrong bits when enabling ASPM L1
Substates. Instead of the L1.x enable bits (PCI_L1SS_CTL1_L1SS_MASK, 0xf), we
cleared the Link Activation Interrupt Enable bit (PCI_L1SS_CAP_L1_PM_SS,
0x10).
Clear the L1.x enable bits before writing the new L1.x configuration.
[bhelgaas: changelog]
Fixes: aeda9adeba ("PCI/ASPM: Configure L1 substate settings")
Link: https://lore.kernel.org/r/1584093227-1292-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v4.11+
The Arm SMMUv3 driver uses pci_{enable,disable}_pasid() and related
functions. Export them to allow the driver to be built as a module.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Will Deacon <will@kernel.org>
Fix the following warning by adding the dependency PCI_MSI_IRQ_DOMAIN
to PCIE_MOBIVEIL_PLAT.
WARNING: unmet direct dependencies detected for PCIE_MOBIVEIL_HOST
Depends on [n]: PCI [=y] && PCI_MSI_IRQ_DOMAIN [=n]
Selected by [y]:
- PCIE_MOBIVEIL_PLAT [=y] && PCI [=y] && (ARCH_ZYNQMP || COMPILE_TEST [=y]) && OF [=y]
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Add PCIE_LNKCAP2_SLS2SPEED macro for transforming raw Link Capabilities 2
values to the pci_bus_speed. This is next to PCIE_SPEED2MBS_ENC() to make
it easier to update both places when adding support for new speeds.
Link: https://lore.kernel.org/r/1581937984-40353-10-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Previously some PCI speed strings came from pci_speed_string(), some came
from the PCIe-specific PCIE_SPEED2STR(), and some came from a PCIe-specific
switch statement. These methods were inconsistent:
pci_speed_string() PCIE_SPEED2STR() switch
------------------ ---------------- ------
33 MHz PCI
...
2.5 GT/s PCIe 2.5 GT/s 2.5 GT/s
5.0 GT/s PCIe 5 GT/s 5 GT/s
8.0 GT/s PCIe 8 GT/s 8 GT/s
16.0 GT/s PCIe 16 GT/s 16 GT/s
32.0 GT/s PCIe 32 GT/s 32 GT/s
Standardize on pci_speed_string() as the single source of these strings.
Note that this adds ".0" and "PCIe" to some messages, including sysfs
"max_link_speed" files, a brcmstb "link up" message, and the link status
dmesg logging, e.g.,
nvme 0000:01:00.0: 16.000 Gb/s available PCIe bandwidth, limited by 5.0 GT/s PCIe x4 link at 0000:00:01.1 (capable of 31.504 Gb/s with 8.0 GT/s PCIe x4 link)
I think it's better to standardize on a single version of the speed text.
Previously we had strings like this:
/sys/bus/pci/slots/0/cur_bus_speed: 8.0 GT/s PCIe
/sys/bus/pci/slots/0/max_bus_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8 GT/s
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8 GT/s
This changes the latter two to match the slots files:
/sys/devices/pci0000:00/0000:00:1c.0/current_link_speed: 8.0 GT/s PCIe
/sys/devices/pci0000:00/0000:00:1c.0/max_link_speed: 8.0 GT/s PCIe
Based-on-patch by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add pci_speed_string() to return a text description of the supplied bus or
link speed. The slot code previously used the private
pci_bus_speed_strings[] array for this purpose, but adding this interface
will enable us to consolidate similar code elsewhere.
Export pcie_link_speed[] and pci_speed_string() so they can be used by
modules.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Embedding the hotplug_slot in zdev structure allows to
greatly simplify the hotplug handling by eliminating
the handling of the slot_list.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
Add a new structure (hv_msi_entry), which is also defined in the TLFS,
to describe the msi entry for HVCALL_RETARGET_INTERRUPT. The structure
is needed because its layout may be different from architecture to
architecture.
Also add a new generic interface hv_set_msi_entry_from_desc() to allow
different archs to set the msi entry from msi_desc.
No functional change, only preparation for the future support of virtual
PCI on non-x86 architectures.
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Currently, retarget_msi_interrupt and other structures it relys on are
defined in pci-hyperv.c. However, those structures are actually defined
in Hypervisor Top-Level Functional Specification [1] and may be
different in sizes of fields or layout from architecture to
architecture. Let's move those definitions into x86's tlfs header file
to support virtual PCI on non-x86 architectures in the future. Note that
"__packed" attribute is added to these structures during the movement
for the same reason as we use the attribute for other TLFS structures in
the header file: make sure the structures meet the specification and
avoid anything unexpected from the compilers.
Additionally, rename struct retarget_msi_interrupt to
hv_retarget_msi_interrupt for the consistent naming convention, also
mirroring the name in TLFS.
[1]: https://docs.microsoft.com/en-us/virtualization/hyper-v-on-windows/reference/tlfs
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Currently HVCALL_RETARGET_INTERRUPT and HV_PARTITION_ID_SELF are defined
in pci-hyperv.c. However, similar to other hypercall related
definitions, it makes more sense to put them in the tlfs header file.
Besides, these definitions are arch-dependent, so for the support of
virtual PCI on non-x86 archs in the future, move them into arch-specific
tlfs header file.
Signed-off-by: Boqun Feng (Microsoft) <boqun.feng@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
The AER error injection mechanism just blindly abuses generic_handle_irq()
which is really not meant for consumption by random drivers. The include of
linux/irq.h should have been a red flag in the first place. Driver code,
unless implementing interrupt chips or low level hypervisor functionality
has absolutely no business with that.
Invoking generic_handle_irq() from non interrupt handling context can have
nasty side effects at least on x86 due to the hardware trainwreck which
makes interrupt affinity changes a fragile beast. Sathyanarayanan triggered
a NULL pointer dereference in the low level APIC code that way. While the
particular pointer could be checked this would only paper over the issue
because there are other ways to trigger warnings or silently corrupt state.
Invoke the new irq_inject_interrupt() mechanism, which has the necessary
sanity checks in place and injects the interrupt via the irq_retrigger()
mechanism, which is at least halfways safe vs. the fragile x86 affinity
change mechanics.
It's safe on x86 as it does not corrupt state, but it still can cause a
premature completion of an interrupt affinity change causing the interrupt
line to become stale. Very unlikely, but possible.
For regular operations this is a non issue as AER error injection is meant
for debugging and testing and not for usage on production systems. People
using this should better know what they are doing.
Fixes: 390e2db824 ("PCI/AER: Abstract AER interrupt handling")
Reported-by: sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lkml.kernel.org/r/20200306130624.098374457@linutronix.de
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Starting with Hyper-V PCI protocol version 1.3, the host VSP can send
PCI_BUS_RELATIONS2 and pass the vNUMA node information for devices on the
bus. The vNUMA node tells which guest NUMA node this device is on based
on guest VM configuration topology and physical device information.
Add code to negotiate v1.3 and process PCI_BUS_RELATIONS2.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
hv_dr_state is used to find present PCI devices on the bus. The structure
reuses struct pci_function_description from VSP message to describe a
device.
To prepare support for pci_function_description v2, decouple this
dependence in hv_dr_state so it can work with both v1 and v2 VSP messages.
There is no functionality change.
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Several device drivers read their Device Serial Number from the PCIe
extended config space.
Introduce a new helper function, pci_get_dsn(). This function reads the
eight bytes of the DSN and returns them as a u64. If the capability does not
exist for the device, the function returns 0.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new constant PCI_STATUS_ERROR_BITS to simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several drivers use the following code sequence:
1. Read PCI_STATUS
2. Mask out non-error bits
3. Action based on error bits set
4. Write back set error bits to clear them
As this is a repeated pattern, add a helper to the PCI core.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that PCIE PHY has been introduced for AXG, the whole has_shared_phy
logic can be mutualized between AXG and G12A platforms.
This new PHY makes use of the shared MIPI/PCIE analog PHY found on AXG
platforms, which need to be used in order to have reliable PCIE
communications.
Signed-off-by: Remi Pommarel <repk@triplefau.lt>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Link speed 32.0 GT/s is supported in PCIe r5.0. Add this speed to
PCIE_SPEED2STR() and PCIE_SPEED2MBS_ENC() to correctly decode it.
This is complementary to de76cda215 ("PCI: Decode PCIe 32 GT/s link
speed").
Link: https://lore.kernel.org/r/1581937984-40353-2-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The following was observed by Kar Hin Ong with RT patchset:
Backtrace:
irq 19: nobody cared (try booting with the "irqpoll" option)
CPU: 0 PID: 3329 Comm: irq/34-nipalk Tainted:4.14.87-rt49 #1
Hardware name: National Instruments NI PXIe-8880/NI PXIe-8880,
BIOS 2.1.5f1 01/09/2020
Call Trace:
<IRQ>
? dump_stack+0x46/0x5e
? __report_bad_irq+0x2e/0xb0
? note_interrupt+0x242/0x290
? nNIKAL100_memoryRead16+0x8/0x10 [nikal]
? handle_irq_event_percpu+0x55/0x70
? handle_irq_event+0x4f/0x80
? handle_fasteoi_irq+0x81/0x180
? handle_irq+0x1c/0x30
? do_IRQ+0x41/0xd0
? common_interrupt+0x84/0x84
</IRQ>
...
handlers:
[<ffffffffb3297200>] irq_default_primary_handler threaded
[<ffffffffb3669180>] usb_hcd_irq
Disabling IRQ #19
The problem being that this device is triggering boot interrupts
due to threaded interrupt handling and masking of the IO-APIC. These
boot interrupts are then forwarded on to the legacy PCH's PIRQ lines
where there is no handler present for the device.
Whenever a PCI device fires interrupt (INTx) to Pin 20 of IOAPIC 2
(GSI 44), the kernel receives two interrupts:
1. Interrupt from Pin 20 of IOAPIC 2 -> Expected
2. Interrupt from Pin 19 of IOAPIC 1 -> UNEXPECTED
Quirks for disabling boot interrupts (preferred) or rerouting the
handler exist but do not address these Xeon chipsets' mechanism:
https://lore.kernel.org/lkml/12131949181903-git-send-email-sassmann@suse.de/
Add a new mechanism via PCI CFG for those chipsets supporting CIPINTRC
register's dis_intx_rout2ich bit.
Link: https://lore.kernel.org/r/20200220192930.64820-2-sean.v.kelley@linux.intel.com
Reported-by: Kar Hin Ong <kar.hin.ong@ni.com>
Tested-by: Kar Hin Ong <kar.hin.ong@ni.com>
Signed-off-by: Sean V Kelley <sean.v.kelley@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Some older compilers have no implementation for the helper for 64-bit
unsigned division/modulo, so linking pcie-brcmstb driver causes the
"undefined reference to `__aeabi_uldivmod'" error.
*rc_bar2_size is always a power of two, because it is calculated as:
"1ULL << fls64(entry->res->end - entry->res->start)", so the modulo
operation in the subsequent check can be replaced by a simple logical
AND with a proper mask.
Link: https://lore.kernel.org/r/20200227115146.24515-1-m.szyprowski@samsung.com
Fixes: c045213703 ("PCI: brcmstb: Add Broadcom STB PCIe host controller driver")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
There exists non-bridge PCIe devices with PCI_VENDOR_ID_QCOM, so limit
the fixup to only affect the relevant PCIe bridges.
Fixes: 322f034366 ("PCI: qcom: Use default config space read function")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # v5.2+
Add support to defer core initialization for the endpoint mode of
operation.
This would enable support for implementations where the core
initialization needs to be deferred until the PCIe reference clock is
available from the host system.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
[lorenzo.pieralisi@arm.com: commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new API dw_pcie_ep_init_notify() to let platform drivers
call it when the core is available for initialization.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Add support to send notifications to EPF from EPC once the core
registers initialization is complete.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Split core initialization code for EP mode into two, one that doesn't
touch core registers and the other that touches core registers. The latter
would be called/skipped based on the EPC feature 'core_init_notifier'.
In platforms where this is skipped, it would be called indirectly
through hooks from the endpoint function driver.
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Convert Tegra PCI host driver to use the common
pci_parse_request_of_pci_ranges().
This allows removing the DT ranges parsing, PCI resource handling, and
private storage of resources from the driver.
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Andrew Murray <andrew.murray@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-tegra@vger.kernel.org
Now that we use kzalloc() to allocate the hbus buffer, we must call
kfree() in the error path as well to prevent memory leakage.
Fixes: 877b911a5b ("PCI: hv: Avoid a kmemleak false positive caused by the hbus buffer")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
In C, there is no need to cast a void * to any other pointer type,
remove an unnecessary cast.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
The PCIe endpoint core relies on the drivers that invoke the
pci_epc_add_epf() API to allocate and assign a function number
to each physical function (PF). Since endpoint function device can
be created by multiple mechanisms (configfs, devicetree, etc..),
allowing each of these mechanisms to assign a function number
would result in mutliple endpoint function devices having the
same function number. In order to avoid this, let EPC core assign
a function number to the endpoint device.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Protect concurrent access to pci_epf_ops with a mutex.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
pci-epc-mem uses a bitmap to manage the Endpoint outbound (OB) address
region. This address region will be shared by multiple endpoint
functions (in the case of multi function endpoint) and it has to be
protected from concurrent access to avoid updating an inconsistent state.
Use a mutex to protect bitmap updates to prevent the memory
allocation API from returning incorrect addresses.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v4.14+
The pci_epc_ops is not intended to be invoked from interrupt context.
Hence replace spin_lock_irqsave and spin_unlock_irqrestore with
mutex_lock and mutex_unlock respectively.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Use atomic_notifier_call_chain() to notify EPC events like linkup to EPF
driver instead of using linkup ops in EPF driver. This is in preparation
for adding proper locking mechanism to EPF ops. This will also enable to
add more events (in addition to linkup) in the future.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Tested-by: Vidya Sagar <vidyas@nvidia.com>
Check the Header Type and exit from the host driver initialization if
it is not in host mode.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
There are some 8-bit and 16-bit registers in PCIe configuration
space, so add these accessors accordingly.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Allow the mobiveil_host_init() function to be used to re-init
host controller's PAB and GPEX CSR register block, since the NXP
integrated Mobiveil IP has to reset and then re-init the PAB
and GPEX CSR registers upon hot-reset.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Subrahmanya Lingappa <l.subrahmanya@mobiveil.co.in>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Platforms integrating the Mobiveil GPEX can implement a specific
mechanism to check the link status.
Add a callback to enable platform specific link status functions.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: updated log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
The Mobiveil GPEX internal MSI/INTx controller is not implemented
in all platforms in which the Mobiveil GPEX is integrated.
Allow platforms to implement their specific interrupt initialization.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Modularize the Mobiveil PCIe host driver according to the abstraction of
Root Complex and Endpoint and move it into a new directory in order to
make it easier to reuse the driver functions to add new host drivers for
systems integrating the Mobiveil PCIe GPEX IP.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Collect the interrupt initialization related operations into
a new function to make code more readable.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Move the host initialization related operations into a new
function so that it can be reused by other platform
PCIe host drivers integrating the Mobiveil GPEX.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
The Mobiveil PCIe controller can work in either Root Complex
mode or Endpoint mode.
Introduce a new structure mobiveil_root_port and abstract the
RC related members into it so that the code can be used by both
modes.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <amurray@thegoodpenguin.co.uk>
Some systems have in-band presence detection disabled for hot-plug PCI
slots but do not report this in the slot capabilities 2 (SLTCAP2) register.
On these systems, presence detect can become active well after the link is
reported to be active, which can cause the slots to be disabled after a
device is connected.
Add a DMI table to flag these systems as having in-band presence detect
disabled.
Link: https://lore.kernel.org/r/20191025190047.38130-4-stuart.w.hayes@gmail.com
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
When in-band presence detect is disabled, PDS may come up at any time or
not at all. PDS being low may indicate that the card is still mating, and
we could expect contact bounce to bring down the link as well.
It is reasonable to assume that most cards will mate in a hotplug slot in
about a second. Thus, when we know PDS only reflects out-of-band presence
detect, it's worthwhile to wait the extra second or so to make sure the
card is properly mated before loading the driver and to prevent the hotplug
code from disabling a device if the presence detect change goes active
after the device is enabled.
Link: https://lore.kernel.org/r/20191025190047.38130-3-stuart.w.hayes@gmail.com
[bhelgaas: use ctrl_info() instead of pci_info()]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Stuart Hayes <stuart.w.hayes@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
The presence detect state (PDS) is normally a logical OR of in-band and
out-of-band (OOB) presence detect. As of PCIe 4.0, there is the option to
disable in-band presence so that the PDS bit always reflects the state of
the out-of-band presence.
The recommendation of the PCIe spec is to disable in-band presence whenever
supported (PCIe r5.0, appendix I implementation note):
Due to architectural issues, the in-band (Physical-Layer-based) portion
of the PD mechanism is deprecated for use with async hot-plug. One issue
is that in-band PD as architected does not detect adapter removal during
certain LTSSM states, notably the L1 and Disabled States. Another issue
is that when both in-band and OOB PD are being used together, the
Presence Detect State bit and its associated interrupt mechanism always
reflect the logical OR of the inband and OOB PD states, and with some
hot-plug hardware configurations, it is important for software to detect
and respond to in-band and OOB PD events independently. If OOB PD is
being used and the associated DSP supports In-Band PD Disable, it is
recommended that the In-Band PD Disable bit be Set, and the Presence
Detect State bit and its associated interrupt mechanism be used
exclusively for OOB PD. As a substitute for in-band PD with async
hot-plug, the reference model uses either the DPC or the DLL Link Active
mechanism.
Link: https://lore.kernel.org/r/20191025190047.38130-2-stuart.w.hayes@gmail.com
[bhelgaas: move PCI_EXP_SLTCAP2 read earlier & print PCI_EXP_SLTCAP2_IBPD
value (suggested by Lukas)]
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Move pcie_to_hpx3_type[] from the stack to static data. This reduces stack
usage and also makes the object code slightly smaller.
Link: https://lore.kernel.org/r/20200210085256.319424-1-colin.king@canonical.com
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
-----BEGIN PGP SIGNATURE-----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=tcy+
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Define to_pci_sysdata() always to fix build breakage when !CONFIG_PCI
(Jason A. Donenfeld)
- Use PF PASID for VFs to fix VF IOMMU bind failures (Kuppuswamy
Sathyanarayanan)
* tag 'pci-v5.6-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/ATS: Use PF PASID for VFs
x86/PCI: Define to_pci_sysdata() even when !CONFIG_PCI
Per PCIe r5.0, sec 9.3.7.14, if a PF implements the PASID Capability, the
PF PASID configuration is shared by its VFs, and VFs must not implement
their own PASID Capability. But commit 751035b8dc ("PCI/ATS: Cache PASID
Capability offset") changed pci_max_pasids() and pci_pasid_features() to
use the PASID Capability of the VF device instead of the associated PF
device. This leads to IOMMU bind failures when pci_max_pasids() and
pci_pasid_features() are called for VFs.
In pci_max_pasids() and pci_pasid_features(), always use the PF PASID
Capability.
Fixes: 751035b8dc ("PCI/ATS: Cache PASID Capability offset")
Link: https://lore.kernel.org/r/fe891f9755cb18349389609e7fed9940fc5b081a.1580325170.git.sathyanarayanan.kuppuswamy@linux.intel.com
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org # v5.5+
Including:
- Allow to compile the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba75) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----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=HMIT
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Allow compiling the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba75) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various
drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
* tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/amd: Remove the unnecessary assignment
iommu/vt-d: Remove unnecessary WARN_ON_ONCE()
iommu/vt-d: Unnecessary to handle default identity domain
iommu/vt-d: Allow devices with RMRRs to use identity domain
iommu/vt-d: Add RMRR base and end addresses sanity check
iommu/vt-d: Mark firmware tainted if RMRR fails sanity check
iommu/amd: Remove unused struct member
iommu/amd: Replace two consecutive readl calls with one readq
iommu/vt-d: Don't reject Host Bridge due to scope mismatch
PCI/ATS: Add PASID stubs
iommu/arm-smmu-v3: Return -EBUSY when trying to re-add a device
iommu/arm-smmu-v3: Improve add_device() error handling
iommu/arm-smmu-v3: Use WRITE_ONCE() when changing validity of an STE
iommu/arm-smmu-v3: Add second level of context descriptor table
iommu/arm-smmu-v3: Prepare for handling arm_smmu_write_ctx_desc() failure
iommu/arm-smmu-v3: Propagate ssid_bits
iommu/arm-smmu-v3: Add support for Substream IDs
iommu/arm-smmu-v3: Add context descriptor tables allocators
iommu/arm-smmu-v3: Prepare arm_smmu_s1_cfg for SSID support
ACPI/IORT: Parse SSID property of named component node
...
- Implement user_access_begin() and friends for our platforms that support
controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure" virtual
machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit VDSO, and
some other improvements.
- A series to use the PCI hotplug framework to control opencapi card's so that
they can be reset and re-read after flashing a new FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to:
Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy, Andrew Donnellan,
Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen Zhou, Christophe Leroy,
Frederic Barrat, Greg Kurz, Jason A. Donenfeld, Joel Stanley, Jordan Niethe,
Julia Lawall, Krzysztof Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus
Walleij, Michael Bringmann, Nathan Chancellor, Nicholas Piggin, Nick
Desaulniers, Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy
Dunlap, Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago Jung
Bauermann, Tyrel Datwyler, Vaibhav Jain.
-----BEGIN PGP SIGNATURE-----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=xpG+
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
- Remove unused modular code from uniphier, which cannot be built as a
module (Masahiro Yamada)
* remotes/lorenzo/pci/uniphier:
PCI: uniphier: remove module code from built-in driver
- Add DT clock/reset info for SDM845 PCIe controller (Bjorn Andersson)
- Add support for SDM845 PCIe controller to the qcom driver (Bjorn
Andersson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Add support for SDM845 PCIe controller
dt-bindings: PCI: qcom: Add support for SDM845 PCIe
- Fix link training so we can do it more than once (Yurii Monakov)
- Fix keystone outbound window mapping (Yurii Monakov)
- Fix error handling when DT lacks "num-viewport" (Kishon Vijay Abraham I)
* remotes/lorenzo/pci/keystone:
PCI: keystone: Fix error handling when "num-viewport" DT property is not populated
PCI: keystone: Fix outbound region mapping
PCI: keystone: Fix link training retries initiation
- Fix memory leak in pci_iov_add_virtfn() (Navid Emamdoost)
- Extend pci_add_dma_alias() so it can add a range of aliases (James
Sewart)
- Add DMA aliases for PLX PEX NTB (James Sewart)
* pci/virtualization:
PCI: Add DMA alias quirk for PLX PEX NTB
PCI: Add nr_devfns parameter to pci_add_dma_alias()
PCI: Fix pci_add_dma_alias() bitmask size
PCI/IOV: Fix memory leak in pci_iov_add_virtfn()
- Support 64-bit addressing for both streaming and coherent DMA (Wesley
Sheng)
- Read vep_vector_number with 16-bit, not 32-bit read (Logan Gunthorpe)
- Add Intercomm Notify and Upstream Error Containment support (Logan
Gunthorpe)
- Remove redundant valid PFF number count (Wesley Sheng)
- Avoid unnecessary CSR read in ISR (Wesley Sheng)
- Rename Gen3-specific constants (Logan Gunthorpe)
- Rework infrastructure to support Gen3- and Gen4-specific code (Logan
Gunthorpe)
- Add Gen4 system info register support (Logan Gunthorpe)
- Add Gen4 flash information interface support (Kelvin Cao)
- Add Gen4 MRPC GAS access permission check (Kelvin Cao)
* pci/switchtec:
PCI/switchtec: Add Gen4 device IDs
PCI/switchtec: Add Gen4 MRPC GAS access permission check
PCI/switchtec: Add Gen4 flash information interface support
PCI/switchtec: Add Gen4 system info register support
PCI/switchtec: Separate Gen3 register structures into unions
PCI/switchtec: Factor out Gen3 ioctl_flash_part_info()
PCI/switchtec: Add 'generation' variable
PCI/switchtec: Rename generation-specific constants
PCI/switchtec: Move check event ID from mask_event() to switchtec_event_isr()
PCI/switchtec: Remove redundant valid PFF number count
PCI/switchtec: Add support for Intercomm Notify and Upstream Error Containment
PCI/switchtec: Fix vep_vector_number ioread width
PCI/switchtec: Use dma_set_mask_and_coherent()
- Clear only bridge windows (not BARs) while assigning bus resources
(Logan Gunthorpe)
- Improve resource assignment for deep hotplug hierarchies, e.g.,
Thunderbolt (Nicholas Johnson)
* pci/resource:
PCI: Allow adjust_bridge_window() to shrink resource if necessary
PCI: Set resource size directly in adjust_bridge_window()
PCI: Rename extend_bridge_window() to adjust_bridge_window()
PCI: Rename extend_bridge_window() parameter
PCI: Consider alignment of hot-added bridges when assigning resources
PCI: Remove local variable usage in pci_bus_distribute_available_resources()
PCI: Pass size + alignment to pci_bus_distribute_available_resources()
PCI: Rename variables
PCI: Remove unnecessary braces
PCI: Don't disable bridge BARs when assigning bus resources
- Add Intel SkyLake-E to the whitelist of host bridges that support
peer-to-peer DMA (Armen Baloyan)
* pci/p2pdma:
PCI/P2PDMA: Add Intel SkyLake-E to the whitelist
- Fix Broadcom iProc quirk so it's applied regardless of whether the
iproc driver is built-in or a module (Wei Liu)
- Add extra delay when resuming AMD Ryzen5/7 XHCI controllers from D3hot
so they work after resume from runtime suspend or suspend-to-idle
(Daniel Drake)
- Fix pci_alloc_irq_vectors() function name typo in docs (Zenghui Yu)
* pci/misc:
Documentation: PCI: Fix pci_alloc_irq_vectors() function name typo
PCI: Increase D3 delay for AMD Ryzen5/7 XHCI controllers
PCI: Add generic quirk for increasing D3hot delay
PCI: iproc: Apply quirk_paxc_bridge() for module as well as built-in
Remove checks for resource size in adjust_bridge_window(). This is
necessary to allow pci_bus_distribute_available_resources() to function
when the kernel parameter "pci=hpmemsize=nn[KMG]" is used to allocate
resources. Because the kernel parameter sets the size of all hotplug
bridges to be the same, there are problems when nested hotplug bridges are
encountered. Fitting a downstream hotplug bridge with size X and normal
bridges with non-zero size Y into parent hotplug bridge with size X is
impossible, and hence the downstream hotplug bridge needs to shrink to fit
into its parent.
Add check for if bridge is extended or shrunken and reflect that in the
call to pci_dbg().
Reset the resource if its new size is zero (if we have run out of a bridge
window resource) to prevent the PCI resource assignment code from
attempting to assign a zero-sized resource.
Link: https://lore.kernel.org/r/PSXP216MB0438D3E2CFE64EBAA32AF691803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Change adjust_bridge_window() to set resource size directly instead of
using additional resource lists.
Because additional resource lists are optional resources, any algorithm
that requires guaranteed allocation that uses them cannot be guaranteed to
work.
Remove the resource from add_list, as a zero-sized additional resource is
redundant.
Update comment in pci_bus_distribute_available_resources() to reflect the
above changes.
Link: https://lore.kernel.org/r/PSXP216MB04386BA48874B56BC5CB0292803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rename extend_bridge_window() to adjust_bridge_window() to prepare for the
fact that the window will be able to shrink. No functional change
intended.
Link: https://lore.kernel.org/r/PSXP216MB0438C47B3473D0C9DE531F18803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In extend_bridge_window(), change "available" parameter name to "new_size".
This makes more sense as this parameter represents the new size for the
window. No functional change intended.
Link: https://lore.kernel.org/r/PSXP216MB043853617ECA4118C472A417803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Change pci_bus_distribute_available_resources() to better handle bridges
with different resource alignment requirements.
The arguments io, mmio and mmio_pref represent the start and end
addresses of resource, into which we must fit the current bridge window.
The steps taken by pci_bus_distribute_available_resources():
- For io, mmio and mmio_pref, increase .start to align with the alignment
of the current bridge window (otherwise the current bridge window may
not fit within the available range).
- For io, mmio and mmio_pref, adjust the current bridge window to the
size after the above.
- Count the number of hotplug bridges and normal bridges on this bus.
- If the total number of bridges is one, give that bridge all of the
resources and return.
- If there are no hotplug bridges, return.
- For io, mmio and mmio_pref, increase .start by the amount required for
each bridge resource on the bus for non hotplug bridges, giving extra
room to make up for alignment of those resources.
- For io, mmio and mmio_pref, calculate the resource size per hotplug
bridge which is available after the previous steps.
- For io, mmio and mmio_pref, distribute the resources to each hotplug
bridge, with the sizes calculated above.
The motivation for fixing this is enabling devices that require greater
than 1MB alignment. This fixes the case where the user hot-adds devices
with BAR alignment >1MB and Linux fails to assign resources to it.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=199581
Link: https://lore.kernel.org/r/PSXP216MB0438C2BFD0FD3691ED9C83F4803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In pci_bus_distribute_available_resources(), use resource_size() rather
than the local available_io, etc. No functional change intended; this just
makes the preceding patch smaller.
[bhelgaas: extracted from https://lore.kernel.org/r/PSXP216MB0438587C47CBEDF365B1EA27803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM]
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Change pci_bus_distribute_available_resources() arguments from
resource_size_t to struct resource to add more information required to get
the alignment correct for bridge windows with alignment >1M.
We require (size, alignment), instead of just (size) which is what is
currently available. The change from resource_size_t to struct resource
does just that.
Note that the struct resource arguments are passed by value and not by
reference. We do not want to pass by reference and change the resource size
of the parent bridge window. We only want the size information.
No functional change intended.
Link: https://lore.kernel.org/r/PSXP216MB0438587C47CBEDF365B1EA27803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM
[bhelgaas: split parts to other patches to reduce the size of this one]
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In pci_bus_distribute_available_resources(), rename:
io => io_per_hp
mmio => mmio_per_hp
mmio_pref => mmio_pref_per_hp
No functional change; this is just to make a subsequent patch smaller.
[bhelgaas: extracted from https://lore.kernel.org/r/PSXP216MB0438587C47CBEDF365B1EA27803C0@PSXP216MB0438.KORP216.PROD.OUTLOOK.COM]
Signed-off-by: Nicholas Johnson <nicholas.johnson-opensource@outlook.com.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add new VMD device IDs that require the bus restriction mode.
Signed-off-by: Sushma Kalakota <sushmax.kalakota@intel.com>
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This adds MSI support to the Broadcom STB PCIe host controller. The MSI
controller is physically located within the PCIe block, however, there
is no reason why the MSI controller could not be moved elsewhere in the
future. MSIX is not supported by the HW.
Since the internal Brcmstb MSI controller is intertwined with the PCIe
controller, it is not its own platform device but rather part of the
PCIe platform device.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Co-developed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
This adds a basic driver for Broadcom's STB PCIe controller, for now
aimed at Raspberry Pi 4's SoC, bcm2711.
Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
Co-developed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[lorenzo.pieralisi@arm.com: updated brcm_pcie_get_rc_bar2_size_and_offset()according to https://lore.kernel.org/linux-pci/be8ddb33a7360af1815cf686f77f3f0913d02be3.camel@suse.de]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Jeremy Linton <jeremy.linton@arm.com>
- remove ioremap_nocache given that is is equivalent to
ioremap everywhere
-----BEGIN PGP SIGNATURE-----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=TUCJ
-----END PGP SIGNATURE-----
Merge tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
Devices on the VMD domain use the VMD endpoint's requester ID and have been
relying on the VMD endpoint's DMA operations. The problem with this was
that VMD domain devices would use the VMD endpoint's attributes when doing
DMA and IOMMU mapping. We can be smarter about this by only using the VMD
endpoint when mapping and providing the correct child device's attributes
during DMA operations.
Remove the dma_map_ops redirect.
Link: https://lore.kernel.org/r/1579613871-301529-7-git-send-email-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Keith Busch <kbusch@kernel.org>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The current DMA alias implementation requires the aliased device be on the
same PCI bus as the requester ID. Add an arch-specific mechanism to point
to another PCI device when doing mapping and PCI DMA alias search. The
default case returns the actual device.
Link: https://lore.kernel.org/r/1579613871-301529-4-git-send-email-jonathan.derrick@intel.com
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Expose VMD's pci_dev pointer in struct pci_sysdata. This will be used
indirectly by intel-iommu.c to find the correct domain.
Link: https://lore.kernel.org/r/1579613871-301529-3-git-send-email-jonathan.derrick@intel.com
[bhelgaas: commit log]
Signed-off-by: Jon Derrick <jonathan.derrick@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Christoph Hellwig <hch@lst.de>
Previously we did not call INIT_KFIFO() for aer_fifo. This leads to
kfifo_put() sometimes returning 0 (queue full) when in fact it is not.
It is easy to reproduce the problem by using aer-inject:
$ aer-inject -s :82:00.0 multiple-corr-nonfatal
The content of the multiple-corr-nonfatal file is as below:
AER
COR RCVR
HL 0 1 2 3
AER
UNCOR POISON_TLP
HL 4 5 6 7
Fixes: 27c1ce8bbe ("PCI/AER: Use kfifo for tracking events instead of reimplementing it")
Link: https://lore.kernel.org/r/1579767991-103898-1-git-send-email-liudongdong3@huawei.com
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Define dev_fmt() with the common prefix of log messages so we don't have to
repeat it in every printk. No functional change intended.
Link: https://lore.kernel.org/r/20191213225709.GA213811@google.com
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PCI error recovery will fail if any device under the Root Port doesn't have
an error_detected callback. Currently only the failure result is printed,
which is not enough to identify the driver that lacks the callback.
Log a message to identify the device with no error_detected callback.
[bhelgaas: tweak log message]
Link: https://lore.kernel.org/r/1576237474-32021-1-git-send-email-yangyicong@hisilicon.com
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
An opencapi slot doesn't have an associated bridge device. It's not
needed for operation, but any warning is displayed through pci_warn()
which uses the pci_dev struct of the assocated bridge device. So wrap
those warning so that a different trace mechanism can be used if it's
an opencapi slot.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-11-fbarrat@linux.ibm.com
The driver only allows to disable a slot in the POPULATED
state. However, if an error occurs while enabling the slot, say
because the link couldn't be trained, then the POPULATED state may not
be reached, yet the power state of the slot is on. So allow to disable
a slot in the REGISTERED state. Removing the devices will do nothing
since it's not populated, and we'll set the power state of the slot
back to off.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-10-fbarrat@linux.ibm.com
Add the opencapi PHBs to the list of PHBs being scanned to look for
slots.
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-9-fbarrat@linux.ibm.com
When changing the slot state, if opal hits an error and tells as such
in the asynchronous reply, the warning "Wrong msg" is logged, which is
rather confusing. Instead we can reuse the better message which is
already used when we couldn't submit the asynchronous opal request
initially.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-8-fbarrat@linux.ibm.com
On powernv, when removing a device through hotplug, the following
warning is logged:
Invalid refcount <.> on <...>
It may be incorrect, the refcount may be set to a higher value than 1
and be valid. of_detach_node() can drop more than one reference. As it
doesn't seem trivial to assert the correct value, let's remove the
warning.
Reviewed-by: Alastair D'Silva <alastair@d-silva.org>
Reviewed-by: Andrew Donnellan <ajd@linux.ibm.com>
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191121134918.7155-7-fbarrat@linux.ibm.com
Fix error handling when "num-viewport" DT property is not populated.
Fixes: 23284ad677 ("PCI: keystone: Add support for PCIe EP in AM654x Platforms")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: stable@vger.kernel.org # v5.2+
To account for parts of the chip that are "harvested" (disabled) due to
silicon flaws, caches on some AMD GPUs must be initialized before ATS is
enabled.
ATS is normally enabled by the IOMMU driver before the GPU driver loads, so
this cache initialization would have to be done in a quirk, but that's too
complex to be practical.
For Navi14 (device ID 0x7340), this initialization is done by the VBIOS,
but apparently some boards went to production with an older VBIOS that
doesn't do it. Disable ATS for those boards.
Link: https://lore.kernel.org/r/20200114205523.1054271-3-alexander.deucher@amd.com
Bug: https://gitlab.freedesktop.org/drm/amd/issues/1015
See-also: d28ca864c4 ("PCI: Mark AMD Stoney Radeon R7 GPU ATS as broken")
See-also: 9b44b0b09d ("PCI: Mark AMD Stoney GPU ATS as broken")
[bhelgaas: squash into one patch, simplify slightly, commit log]
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
Now that Gen4 is properly supported, advertise support in the module's
device ID table and add the same IDs to the list of switchtec quirks.
[logang@deltatee.com: add commit message and quirk IDs]
Link: https://lore.kernel.org/r/20200115035648.2578-8-logang@deltatee.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gen4 hardware provides new MRPC commands to read and write directly from
any address in the PCI BAR (which Microsemi refers to as GAS). Since
accessing BARs can be dangerous and break the driver, we don't want
unprivileged users to have this ability.
Therefore, require CAP_SYS_ADMIN for the local and remote GAS access MRPC
commands. Privileged processes will already have access to the BAR through
the sysfs resource file so this doesn't give userspace any capabilities it
didn't already have.
[logang@deltatee.com: rework commit message]
Link: https://lore.kernel.org/r/20200106190337.2428-11-logang@deltatee.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add the new flash_info registers struct and the implementation of
ioctl_flash_part_info() for the new Gen4 hardware.
[logang@deltatee.com: rewrote commit message]
Link: https://lore.kernel.org/r/20200115035648.2578-7-logang@deltatee.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add the Gen4-specific system info registers and ensure their usage is
guarded by a check on the device's generation.
Link: https://lore.kernel.org/r/20200115035648.2578-6-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Since the sys_info and flash_info registers differ significantly in Gen4
hardware, separate out the Gen3 registers into their own structure with a
union in the main structure.
No functional changes intended.
Link: https://lore.kernel.org/r/20200115035648.2578-5-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Refactor ioctl_flash_part_info() into a Gen3-specific function because the
registers for flash partition information have changed significantly in
Gen4 and will require a completely different implementation.
No functional changes intended.
Co-developed-by: Kelvin Cao <kelvin.cao@microchip.com>
Link: https://lore.kernel.org/r/20200115035648.2578-4-logang@deltatee.com
Signed-off-by: Kelvin Cao <kelvin.cao@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a generation variable passed through the device ID table and test for
Gen3-specific registers. This will allow us to add Gen4 and other devices
that extend the programming model.
Link: https://lore.kernel.org/r/20200115035648.2578-3-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Gen4 hardware will have different values for the SWITCHTEC_X_RUNNING and
SWITCHTEC_IOCTL_NUM_PARTITIONS, so rename them with GEN3 in their name.
No functional changes intended.
Link: https://lore.kernel.org/r/20200115035648.2578-2-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The event ID check doesn't depend on anything in the mask_all_events() to
mask_event() path. Do it in switchtec_event_isr() to avoid the CSR read in
mask_event().
Link: https://lore.kernel.org/r/20200106190337.2428-6-logang@deltatee.com
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the Inter Fabric Manager Communication (Intercomm) Notify
event in PAX variants of Switchtec hardware and the Upstream Error
Containment port in the MR1 release of Gen3 firmware.
Link: https://lore.kernel.org/r/20200106190337.2428-4-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
When resuming from hibernation (S4, also known as "suspend to disk") on a
VM, we have seen invalid config space, e.g.,
serial 0000:00:16.3: restoring config space at offset 0x14 (was 0x9104e000, writing 0xffffffff)
To help debug problems like this, log the config space being saved before
suspend, similar to the log in pci_restore_config_dword() when resuming.
Link: https://lore.kernel.org/r/20200113060724.19571-1-yu.c.chen@intel.com
[bhelgaas: commit log]
Signed-off-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Len Brown <lenb@kernel.org>
Some PCI bridges implement BARs in addition to bridge windows. For
example, here's a PLX switch:
04:00.0 PCI bridge: PLX Technology, Inc. PEX 8724 24-Lane, 6-Port PCI
Express Gen 3 (8 GT/s) Switch, 19 x 19mm FCBGA (rev ca)
(prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 30, NUMA node 0
Memory at 90a00000 (32-bit, non-prefetchable) [size=256K]
Bus: primary=04, secondary=05, subordinate=0a, sec-latency=0
I/O behind bridge: 00002000-00003fff
Memory behind bridge: 90000000-909fffff
Prefetchable memory behind bridge: 0000380000800000-0000380000bfffff
Previously, when the kernel assigned resource addresses (with the
pci=realloc command line parameter, for example) it could clear the struct
resource corresponding to the BAR. When this happened, lspci would report
this BAR as "ignored":
Region 0: Memory at <ignored> (32-bit, non-prefetchable) [size=256K]
This is because the kernel reports a zero start address and zero flags
in the corresponding sysfs resource file and in /proc/bus/pci/devices.
Investigation with 'lspci -x', however, shows the BIOS-assigned address
will still be programmed in the device's BAR registers.
It's clearly a bug that the kernel lost track of the BAR value, but in most
cases, this still won't result in a visible issue because nothing uses the
memory, so nothing is affected. However, when an IOMMU is in use, it will
not reserve this space in the IOVA because the kernel no longer thinks the
range is valid. (See dmar_init_reserved_ranges() for the Intel
implementation of this.)
Without the proper reserved range, a DMA mapping may allocate an IOVA that
matches a bridge BAR, which results in DMA accesses going to the BAR
instead of the intended RAM.
The problem was in pci_assign_unassigned_root_bus_resources(). When any
resource from a bridge device fails to get assigned, the code set the
resource's flags to zero. This makes sense for bridge windows, as they
will be re-enabled later, but for regular BARs, it makes the kernel
permanently lose track of the fact that they decode address space.
Change pci_assign_unassigned_root_bus_resources() and
pci_assign_unassigned_bridge_resources() so they only clear "res->flags"
for bridge *windows*, not bridge BARs.
Fixes: da7822e5ad ("PCI: update bridge resources to get more big ranges when allocating space (again)")
Link: https://lore.kernel.org/r/20200108213208.4612-1-logang@deltatee.com
[bhelgaas: commit log, check for pci_is_bridge()]
Reported-by: Kit Chow <kchow@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
builtin_platform_driver() and MODULE_* are always odd combination.
This file is not compiled as a module by anyone because
CONFIG_PCIE_UNIPHIER is a bool option.
Let's remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove" code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Fix up inconsistent usage of upper and lowercase letters in "Exynos"
name.
"EXYNOS" is not an abbreviation but a regular trademarked name.
Therefore it should be written with lowercase letters starting with
capital letter.
The lowercase "Exynos" name is promoted by its manufacturer Samsung
Electronics Co., Ltd., in advertisement materials and on website.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Fix AFI_PEX2_CTRL reg offset for Tegra30 by moving it from the Tegra20
SoC struct where it erroneously got added. This fixes the AFI_PEX2_CTRL
reg offset being uninitialised subsequently failing to bring up the
third PCIe port.
Fixes: adb2653b3d ("PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of SoC struct")
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
pm_runtime_get_sync() returns the device's usage counter. This might
be >0 if the device is already powered up or CONFIG_PM is disabled.
Abort probe function on real error only.
Fixes: da76ba5096 ("PCI: tegra: Add power management support")
Link: https://lore.kernel.org/r/20191216111825.28136-1-david.engraf@sysgo.com
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Cc: stable@vger.kernel.org # v4.17+
The Keystone outbound Address Translation Unit (ATU) maps PCI MMIO space in
8 MB windows. When programming the ATU windows, we previously incremented
the starting address by 8, not 8 MB, so all the windows were mapped to the
first 8 MB. Therefore, only 8 MB of MMIO space was accessible.
Update the loop so it increments the starting address by 8 MB, not 8, so
more MMIO space is accessible.
Fixes: e75043ad97 ("PCI: keystone: Cleanup outbound window configuration")
Link: https://lore.kernel.org/r/20191004154811.GA31397@monakov-y.office.kontur-niirs.ru
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
[bhelgaas: commit log]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: stable@vger.kernel.org # v4.20+
ks_pcie_stop_link() function does not clear LTSSM_EN_VAL bit so
link training was not triggered more than once after startup.
In configurations where link can be unstable during early boot,
for example, under low temperature, it will never be established.
Fixes: 0c4ffcfe1f ("PCI: keystone: Add TI Keystone PCIe driver")
Signed-off-by: Yurii Monakov <monakov.y@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Andrew Murray <andrew.murray@arm.com>
Cc: stable@vger.kernel.org
The SDM845 has one Gen2 and one Gen3 controller, add support for these.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Use DesignWare helper functions to configure Fast Training
Sequence. Drop the respective code in the driver.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Add support to PCIe RC controller on Intel Gateway SoCs.
PCIe controller is based of Synopsys DesignWare PCIe core.
Intel PCIe driver requires Upconfigure support, Fast Training
Sequence and link speed configurations. So adding the respective
helper functions in the PCIe DesignWare framework.
It also programs hardware autonomous speed during speed
configuration so defining it in pci_regs.h.
Also, mark Intel PCIe driver depends on MSI IRQ Domain
as Synopsys DesignWare framework depends on the
PCI_MSI_IRQ_DOMAIN.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Andrew Murray <andrew.murray@arm.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Acked-by: Gustavo Pimentel <gustavo.pimentel@synopsys.com>
vep_vector_number is actually a 16 bit register which should be read with
ioread16() instead of ioread32().
Fixes: 080b47def5 ("MicroSemi Switchtec management interface driver")
Link: https://lore.kernel.org/r/20200106190337.2428-3-logang@deltatee.com
Reported-by: Doug Meyer <dmeyer@gigaio.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Use dma_set_mask_and_coherent() instead of dma_set_coherent_mask() as the
Switchtec hardware fully supports 64bit addressing and we should set both
the streaming and coherent masks the same.
[logang@deltatee.com: reworked commit message]
Fixes: aff614c633 ("switchtec: Set DMA coherent mask")
Link: https://lore.kernel.org/r/20200106190337.2428-2-logang@deltatee.com
Signed-off-by: Wesley Sheng <wesley.sheng@microchip.com>
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Bjorn Helgaas