Extend ECC decoding support for F16h M30h. Tested on F16h M30h with ECC
turned on using mce_amd_inj module and the patch works fine.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/1392913726-16961-1-git-send-email-Aravind.Gopalakrishnan@amd.com
Tested-by: Arindam Nath <Arindam.Nath@amd.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Fix the following warning:
drivers/edac/i7core_edac.c: In function "core_mce_output_error":
drivers/edac/i7core_edac.c:1711:8: warning: variable "type" set but not used [-Wunused-but-set-variable]
char *type, *optype, *err;
^
According to Mauro, type can just be dropped, as tp_event now maps if
the error is corrected, uncorrected non-fatal or uncorrected fatal
one.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224171358.692d7e5a@endymion.delvare
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
The first call to pci_get_device() in i82875p_probe1() is useless. The
result is immediately reset at the beginning of
i82875p_setup_overfl_dev(), which then issues the same
pci_get_device() call. Dropping the redundant call avoids a device
reference leak.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224160316.60e55fb6@endymion.delvare
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
pvt->bridge_ck always points to the same device as pvt->dev_d0f1, so
get rid of the former and only use the latter.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Aristeu Rozanski <aris@redhat.com>
Link: http://lkml.kernel.org/r/20140224151544.16ba28a0@endymion.delvare
Cc: Mark Gross <mark.gross@intel.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
pci_get_device() decrements the reference count of "from" (last
argument) so when we break off the loop successfully we have only one
device reference - and we don't know which device we have. If we want
a reference to each device, we must take them explicitly and let
the pci_get_device() walk complete to avoid duplicate references.
This is serious, as over-putting device references will cause
the device to eventually disappear. Without this fix, the kernel
crashes after a few insmod/rmmod cycles.
Tested on an Intel S7000FC4UR system with a 7300 chipset.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224111656.09bbb7ed@endymion.delvare
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
The reference count changes done by pci_get_device can be a little
misleading when the usage diverges from the most common scheme. The
reference count of the device passed as the last parameter is always
decreased, even if the function returns no new device. So if we are
going to try alternative device IDs, we must manually increment the
device reference count before each retry. If we don't, we end up
decreasing the reference count, and after a few modprobe/rmmod cycles
the PCI devices will vanish.
In other words and as Alan put it: without this fix the EDAC code
corrupts the PCI device list.
This fixes kernel bug #50491:
https://bugzilla.kernel.org/show_bug.cgi?id=50491
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Link: http://lkml.kernel.org/r/20140224093927.7659dd9d@endymion.delvare
Reviewed-by: Alan Cox <alan@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: stable@vger.kernel.org
Signed-off-by: Borislav Petkov <bp@suse.de>
We want to still be able to issue some error information on systems for
which there is no decoding support (think older distro kernels here,
for example). Therefore, we allow module registration but skip the
per-family bank-specific decoders and issue the general information
only, i.e.:
[ 46.822828] [Hardware Error]: Error Status: Uncorrected, software containable error.
[ 46.822846] [Hardware Error]: CPU:0 (15:30:0) MC0_STATUS[-|UE|-|-|-|-|-]: 0xa000000000010f0f
[ 46.822858] [Hardware Error]: cache level: L3/GEN, mem/io: GEN, mem-tx: GEN, part-proc: GEN (timed out)
with the hope that it still contains helpful useful bits.
Suggested-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Tested-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/1392659391-2411-1-git-send-email-Aravind.Gopalakrishnan@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
We checked that "npages" was not zero a couple lines earlier so we can
remove this and pull the code in one indent level.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: http://lkml.kernel.org/r/20140213111738.GB15549@elgon.mountain
Signed-off-by: Borislav Petkov <bp@suse.de>
On a system with four Intel processors, it generates too many messages
"EDAC sbridge: Seeking for: dev 1d.3 PCI ID xxxx". And it doesn't give
many useful information for normal users, so change log level from INFO
to DEBUG.
Signed-off-by: Jiang Liu <jiang.liu@linux.intel.com>
Link: http://lkml.kernel.org/r/1392613824-11230-1-git-send-email-jiang.liu@linux.intel.com
Acked-by: Aristeu Rozanski <aris@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
We're using edac_mc_workq_setup() both on the init path, when
we load an edac driver and when we change the polling period
(edac_mc_reset_delay_period) through /sys/.../edac_mc_poll_msec.
On that second path we don't need to init the workqueue which has been
initialized already.
Thanks to Tejun for workqueue insights.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: <stable@vger.kernel.org>
Sanitize code even more to accept unsigned longs only and to not allow
polling intervals below 1 second as this is unnecessary and doesn't make
much sense anyway for polling errors.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1391457913-881-1-git-send-email-prarit@redhat.com
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: <stable@vger.kernel.org>
Currently, i3200_edac.c forgets to call pci_disable_device() during a
process of disabling device. This patch adds that call.
The problem was detected by Huqiu Liu.
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Hitoshi Mitake <mitake.hitoshi@lab.ntt.co.jp>
Link: http://lkml.kernel.org/r/1389587178-10167-1-git-send-email-mitake.hitoshi@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
This was found by Huqiu Liu using a static analysis.
Reported-by: Huqiu Liu <liuhq11@mails.tsinghua.edu.cn>
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Link: http://lkml.kernel.org/r/20140116162021.GY15716@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The last parameter, pvt->bridge_ck, is always NULL as far as I can
see, so just use that.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: Aristeu Rozanski <aris@redhat.com>
Link: http://lkml.kernel.org/r/20140130091101.22f2b550@endymion.delvare
Cc: Mark Gross <mark.gross@intel.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull x86 RAS changes from Ingo Molnar:
- SCI reporting for other error types not only correctable ones
- GHES cleanups
- Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which,
if done properly in the BIOS, makes a corresponding EDAC module
redundant
- PCIe AER tracepoint severity levels fix
- Error path correction for the mce device init
- MCE timer fix
- Add more flexibility to the error injection (EINJ) debugfs interface
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mce: Fix mce_start_timer semantics
ACPI, APEI, GHES: Cleanup ghes memory error handling
ACPI, APEI: Cleanup alignment-aware accesses
ACPI, APEI, GHES: Do not report only correctable errors with SCI
ACPI, APEI, EINJ: Changes to the ACPI/APEI/EINJ debugfs interface
ACPI, eMCA: Combine eMCA/EDAC event reporting priority
EDAC, sb_edac: Modify H/W event reporting policy
EDAC: Add an edac_report parameter to EDAC
PCI, AER: Fix severity usage in aer trace event
x86, mce: Call put_device on device_register failure
* misc small enhancements/fixes all over the place.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=EJ+3
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
- mpc85xx PCIe error interrupt support
- misc small enhancements/fixes all over the place.
* tag 'edac_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Don't try to cancel workqueue when it's never setup
e752x_edac: Fix pci_dev usage count
sb_edac: Mark get_mci_for_node_id as static
EDAC: Mark edac_create_debug_nodes as static
amd64_edac: Remove "amd64" prefix from static functions
amd64_edac: Simplify code around decode_bus_error
amd64_edac: Mark amd64_decode_bus_error as static
EDAC: Remove DEFINE_PCI_DEVICE_TABLE macro
amd64_edac: Fix condition to verify max channels allowed for F15 M30h
edac/85xx: Add PCIe error interrupt edac support
We only setup a workqueue for edac devices that use the polling
method. We still try to cancel the workqueue if an edac_device
uses the irq method though. This causes a warning from debug
objects when we remove an edac device:
WARNING: CPU: 0 PID: 56 at lib/debugobjects.c:260 debug_print_object+0x98/0xc0()
ODEBUG: assert_init not available (active state 0) object type: timer_list hint: stub_timer+0x0/0x28
Modules linked in: krait_edac(-)
CPU: 0 PID: 56 Comm: rmmod Not tainted 3.12.0-rc2-00035-g15292a0 #69
(unwind_backtrace+0x0/0x144)
(show_stack+0x20/0x24)
(dump_stack+0x74/0xb4)
(warn_slowpath_common+0x78/0x9c)
(warn_slowpath_fmt+0x40/0x48)
(debug_print_object+0x98/0xc0)
(debug_object_assert_init+0xdc/0xec)
(del_timer+0x24/0x7c)
(try_to_grab_pending+0xc0/0x1b0)
(cancel_delayed_work+0x2c/0xa0)
(edac_device_workq_teardown+0x1c/0x38)
(edac_device_del_device+0xb8/0xe4)
(krait_edac_remove+0x50/0x70 [krait_edac])
(platform_drv_remove+0x24/0x28)
(__device_release_driver+0x68/0xc0)
(driver_detach+0xc4/0xc8)
(bus_remove_driver+0xac/0x114)
(driver_unregister+0x38/0x58)
(platform_driver_unregister+0x1c/0x20)
(krait_edac_driver_exit+0x14/0x1c [krait_edac])
(SyS_delete_module+0x178/0x2b4)
Fix it by skipping the workqueue teardown for such devices.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Link: http://lkml.kernel.org/r/1388434457-4194-2-git-send-email-sboyd@codeaurora.org
Signed-off-by: Borislav Petkov <bp@suse.de>
In case the device 0, function 1 is not found using pci_get_device(),
pci_scan_single_device() will be used but, differently than
pci_get_device(), it allocates a pci_dev but doesn't does bump the usage
count on the pci_dev and after few module removals and loads the pci_dev
will be freed.
Signed-off-by: Aristeu Rozanski <aris@redhat.com>
Reviewed-by: mark gross <mark.gross@intel.com>
Link: http://lkml.kernel.org/r/20131205153755.GL4545@redhat.com
Signed-off-by: Borislav Petkov <bp@suse.de>
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=r//I
-----END PGP SIGNATURE-----
Merge tag 'ras_for_3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp into x86/ras
Pull RAS updates from Borislav Petkov:
* Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which, if
done properly in the BIOS, makes a corresponding EDAC module redundant,
from Gong Chen.
* PCIe AER tracepoint severity levels fix, from Rui Wang.
* Error path correction for the mce device init, from Levente Kurusa.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch marks the function get_mci_for_node_id() as static because it
is not used outside of sb_edac.c.
Thus, it also eliminates the following warning:
drivers/edac/sb_edac.c:918:22: warning: no previous prototype for ‘get_mci_for_node_id’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/0441f508186fc4eeabc8e9c3e4dde013d99405d4.1387029387.git.rashika.kheria@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
This patch marks the function edac_create_debug_nodes() as static
because it is not used outside of edac_mc_sysfs.c.
Thus, it also eliminates the following warning:
drivers/edac/edac_mc_sysfs.c:917:5: warning: no previous prototype for ‘edac_create_debug_nodes’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/a1c863b08c0d6f67d03280cf908c771bf26a3239.1387029387.git.rashika.kheria@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
This patch marks the function amd64_decode_bus_error() as static because
it is not used outside of amd64_edac.c.
It also eliminates the following warning:
drivers/edac/amd64_edac.c:2038:6: warning: no previous prototype for ‘amd64_decode_bus_error’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Link: http://lkml.kernel.org/r/7cddbd4c69ed493f183383e98853181aaf75b26b.1387029387.git.rashika.kheria@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Newer Intel platforms support more than one method to report H/W event.
On this kind of platform, H/W event report can adopt new method and
traditional EDAC method should be disabled. Moreover, if EDAC event
report method is set to *force*, it means event must be reported via
EDAC interface. IOW, it overrides the default event report policy.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1386310630-12529-3-git-send-email-gong.chen@linux.intel.com
[ Boris: massage commit and error messages ]
Signed-off-by: Borislav Petkov <bp@suse.de>
This new parameter is used to control how to report HW error reporting,
especially for newer Intel platform, like Ivybridge-EX, which contains
an enhanced error decoding functionality in the firmware, i.e. eMCA.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1386310630-12529-2-git-send-email-gong.chen@linux.intel.com
[ Boris: massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Currently, there is no other bus that has something like this macro for
their device ids. Thus, DEFINE_PCI_DEVICE_TABLE macro should be removed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Link: http://lkml.kernel.org/r/001c01ceefb3$5724d860$056e8920$%han@samsung.com
[ Boris: swap commit message with better one. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The value returned from 'f15_m30h_determine_channel' will
always be 0x3 max. The condition
(channel > 4 || channel < 0)
works as hardware never returns a value of 4, but
it leads to static checker analysis errors like
http://marc.info/?l=linux-edac&m=138607615131951&w=2.
Fix that.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/20131203130857.GA32170@elgon.mountain
[ Boris: massage commit message a bit. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Fix this:
In file included from drivers/edac/sb_edac.c:27:0:
drivers/edac/sb_edac.c: In function ‘sbridge_mce_output_error’:
drivers/edac/edac_core.h:50:8: warning: ‘limit’ may be used uninitialized in this function [-Wmaybe-uninitialized]
printk(level "EDAC " prefix ": " fmt, ##arg)
^
drivers/edac/sb_edac.c:948:25: note: ‘limit’ was declared here
u64 ch_addr, offset, limit, prv = 0;
Limit can be initialized to 0. The only way limit wouldn't be
initialized is if there are no DIMMs present (which would be a bug of
course) and it'd fail on the next test.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Link: http://lkml.kernel.org/r/20131121122021.GD26009@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
Add pcie error interrupt edac support for mpc85xx, p3041, p4080, and
p5020. The mpc85xx uses the legacy interrupt report mechanism - the
error interrupts are reported directly to mpic. While the p3041/
p4080/p5020 attaches the most of error interrupts to interrupt zero. And
report error interrupts to mpic via interrupt 0.
This patch can handle both of them.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Link: http://lkml.kernel.org/r/1384712714-8826-3-git-send-email-morbidrsa@gmail.com
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Dave Jiang <dave.jiang@gmail.com>
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull EDAC driver updates from Mauro Carvalho Chehab:
- sb_edac: add support for Ivy Bridge support
- cell_edac: add a missing of_node_put() call
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
cell_edac: fix missing of_node_put
sb_edac: add support for Ivy Bridge
sb_edac: avoid decoding the same error multiple times
sb_edac: rename mci_bind_devs()
sb_edac: enable multiple PCI id tables to be used
sb_edac: rework sad_pkg
sb_edac: allow different interleave lists
sb_edac: allow different dram_rule arrays
sb_edac: isolate TOHM retrieval
sb_edac: rename pci_br
sb_edac: isolate TOLM retrieval
sb_edac: make RANK_CFG_A value part of sbridge_info
Highlights:
* Support for Calxeda ECX-2000 memory controller, from Robert Richter
* Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob Herring
and Robert Richter
* New maintainer for Freescale's MPC85xx EDAC driver: Johannes Thumshirn
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=pU/h
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"Following up on last week's discussion, here's my part of the EDAC
pile, highlights in the signed tag.
The last two patches have a date from just now because I've just
applied them to the tree after Johannes sent them to me earlier. I
decided to forward them now because they're trivial.
There's a third one for MPC85xx which adds PCIe error interrupt
support but since it is not so trivial and hasn't seen any linux-next
time, I'm deferring it to 3.14
EDAC update highlights:
- Support for Calxeda ECX-2000 memory controller, from Robert Richter
- Misc Calxeda Highbank drivers and EDAC core cleanups, from Rob
Herring and Robert Richter
- New maintainer for Freescale's MPC85xx EDAC driver: Johannes
Thumshirn"
* tag 'edac_for_3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
edac/85xx: Remove mpc85xx_pci_err_remove
EDAC: Add edac-mpc85xx driver to MAINTAINERS
edac, highbank: Moving error injection to sysfs for edac
edac, highbank: Add MAINTAINERS entry
edac: Unify reporting of device info for device, mc and pci
edac, highbank: Improve and unify naming
edac, highbank: Add Calxeda ECX-2000 support
ARM: dts: calxeda: move memory-controller node out of ecx-common.dtsi
edac, highbank: Fix interrupt setup of mem and l2 controller
Remove mpc85xx_pci_err_remove(...) which is obsolete, this removes the
compiler warning which can be seen when building the driver either
statically or as a module.
Signed-off-by: Johannes Thumshirn <morbidrsa@gmail.com>
Link: https://lkml.kernel.org/r/20131112161901.GA15637@jtlinux
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@men.de>
Signed-off-by: Borislav Petkov <bp@suse.de>
Since Ivy Bridge memory controller is very similar to Sandy Bridge, it's
wiser to modify sb_edac to support both instead of creating another
driver.
[m.chehab@samsung.com: Fix CodingStyle]
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Whenever the extended error reporting is active, multiple MCEs will be
generated for the same event, which will lead to multiple repeated
errors to be reported. So check ADDRV and only decode the error if the
MCE address is valid.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed to allow separated PCI id tables for Sandy Bridge and Ivy
Bridge.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for Ivy Bridge support
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Ivy Bridge has more than one, so rename pci_br to pci_br0
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation for the Ivy Bridge support.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is in preparation of Ivy Bridge support.
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for deferred
probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJSgPQ4AAoJEMhvYp4jgsXif28H/1WkrXq5+lCFQZF8nbYdE2h0
R8PsfiJJmAl6/wFgQTsRel+ScMk2hiP08uTyqf2RLnB1v87gCF7MKVaLOdONfUDi
huXbcQGWCmZv0tbBIklxJe3+X3FIJch4gnyUvPudD1m8a0R0LxWXH/NhdTSFyB20
PNjhN/IzoN40X1PSAhfB5ndWnoxXBoehV/IVHVDU42vkPVbVTyGAw5qJzHW8CLyN
2oGTOalOO4ffQ7dIkBEQfj0mrgGcODToPdDvUQyyGZjYK2FY2sGrjyquir6SDcNa
Q4gwatHTu0ygXpyphjtQf5tc3ZCejJ/F0s3olOAS1ahKGfe01fehtwPRROQnCK8=
=GCbY
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
"DeviceTree updates for 3.13. This is a bit larger pull request than
usual for this cycle with lots of clean-up.
- Cross arch clean-up and consolidation of early DT scanning code.
- Clean-up and removal of arch prom.h headers. Makes arch specific
prom.h optional on all but Sparc.
- Addition of interrupts-extended property for devices connected to
multiple interrupt controllers.
- Refactoring of DT interrupt parsing code in preparation for
deferred probe of interrupts.
- ARM cpu and cpu topology bindings documentation.
- Various DT vendor binding documentation updates"
* tag 'devicetree-for-3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (82 commits)
powerpc: add missing explicit OF includes for ppc
dt/irq: add empty of_irq_count for !OF_IRQ
dt: disable self-tests for !OF_IRQ
of: irq: Fix interrupt-map entry matching
MIPS: Netlogic: replace early_init_devtree() call
of: Add Panasonic Corporation vendor prefix
of: Add Chunghwa Picture Tubes Ltd. vendor prefix
of: Add AU Optronics Corporation vendor prefix
of/irq: Fix potential buffer overflow
of/irq: Fix bug in interrupt parsing refactor.
of: set dma_mask to point to coherent_dma_mask
of: add vendor prefix for PHYTEC Messtechnik GmbH
DT: sort vendor-prefixes.txt
of: Add vendor prefix for Cadence
of: Add empty for_each_available_child_of_node() macro definition
arm/versatile: Fix versatile irq specifications.
of/irq: create interrupts-extended property
microblaze/pci: Drop PowerPC-ism from irq parsing
of/irq: Create of_irq_parse_and_map_pci() to consolidate arch code.
of/irq: Use irq_of_parse_and_map()
...
Always have the error injection i/f available, even if there is no
debugfs or EDAC_DEBUG enabled. We need this for testing production
kernels and environments.
Thus, the entry moves from:
/sys/kernel/debug/edac/mc0/inject_ctrl
to:
/sys/devices/system/edac/mc/mc0/inject_ctrl
No other changes of the interface.
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Signed-off-by: Robert Richter <rric@kernel.org>
Log messages slightly differ between edac subsystems. Unifying it.
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Robert Richter <rric@kernel.org>
Assinging correct names of the 'hb_mc_edac' and 'hb_l2_edac' edac
modules for module, controller and device. Reported values for
Highbank in dmesg are now:
EDAC MC0: Giving out device to module hb_mc_edac controller
calxeda,hb-ddr-ctrl: DEV fff00000.memory-controller (INTERRUPT)
EDAC DEVICE0: Giving out device to module hb_l2_edac controller
calxeda,hb-sregs-l2-ecc: DEV fff3c200.sregs (INTERRUPT)
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Robert Richter <rric@kernel.org>
Implement edac support for Calxeda ECX-2000.
The ECX-2000 memory controller is similar to Highbank but has
different register bases for error and interrupt registers. There is
an own device tree name "calxeda,ecx-2000-ddr-ctrl" for identification
and initialization of the ECX-2000 and its base addresses.
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Robert Richter <rric@kernel.org>
Register and enable interrupts after the edac registration. Otherwise
incomming ecc error interrupts lead to crashes during device setup.
Fixing this in drivers for mc and l2.
Signed-off-by: Robert Richter <robert.richter@linaro.org>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Cc: stable <stable@vger.kernel.org> # 3.6+
Signed-off-by: Robert Richter <rric@kernel.org>
In latest UEFI spec(by now it's 2.4) there are some new
fields for memory error reporting. Add these new fields for
ghes_edac interface.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
In latest UEFI spec(by now it is 2.4) memory error definition
for CPER (UEFI 2.4 Appendix N Common Platform Error Record)
adds some new fields. These fields help people to locate
memory error to an actual DIMM location.
Original-author: Tony Luck <tony.luck@intel.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
GENMASK is used to create a contiguous bitmask([hi:lo]). It is
implemented twice in current kernel. One is in EDAC driver, the other
is in SiS/XGI FB driver. Move it to a more generic place for other
usage.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Pull Tile arch updates from Chris Metcalf:
"These changes bring in a bunch of new functionality that has been
maintained internally at Tilera over the last year, plus other stray
bits of work that I've taken into the tile tree from other folks.
The changes include some PCI root complex work, interrupt-driven
console support, support for performing fast-path unaligned data
fixups by kernel-based JIT code generation, CONFIG_PREEMPT support,
vDSO support for gettimeofday(), a serial driver for the tilegx
on-chip UART, KGDB support, more optimized string routines, support
for ftrace and kprobes, improved ASLR, and many bug fixes.
We also remove support for the old TILE64 chip, which is no longer
buildable"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile: (85 commits)
tile: refresh tile defconfig files
tile: rework <asm/cmpxchg.h>
tile PCI RC: make default consistent DMA mask 32-bit
tile: add null check for kzalloc in tile/kernel/setup.c
tile: make __write_once a synonym for __read_mostly
tile: remove support for TILE64
tile: use asm-generic/bitops/builtin-*.h
tile: eliminate no-op "noatomichash" boot argument
tile: use standard tile_bundle_bits type in traps.c
tile: simplify code referencing hypervisor API addresses
tile: change <asm/system.h> to <asm/switch_to.h> in comments
tile: mark pcibios_init() as __init
tile: check for correct compiler earlier in asm-offsets.c
tile: use standard 'generic-y' model for <asm/hw_irq.h>
tile: use asm-generic version of <asm/local64.h>
tile PCI RC: add comment about "PCI hole" problem
tile: remove DEBUG_EXTRA_FLAGS kernel config option
tile: add virt_to_kpte() API and clean up and document behavior
tile: support FRAME_POINTER
tile: support reporting Tilera hypervisor statistics
...
dct_base and dct_limit obtain 32 bit register values when they read
their respective pci config space registers. A left shift beyond 32 bits
will cause them to wrap around. Similar case for chan_addr as can be
seen from the bug report (link below). In the patch, we rectify this by
casting chan_addr to u64 and by comparing dct_base and dct_limit against
properly shifted sys_addr in order to compare the correct bits.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/20130819132302.GA12171@elgon.mountain
Signed-off-by: Borislav Petkov <bp@suse.de>
Basically we want to cover all 0x0-0xf models, i.e. Orochi and later.
Cc: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Link: http://lkml.kernel.org/r/20130819192321.GF4165@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
The struct should be terminated by using empty braces in order to
fix the following sparse warning.
drivers/edac/cpc925_edac.c:792:10: warning: Using plain integer as NULL pointer
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[ drop obvious comment ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Now that we cache (family, model, stepping) locally, use them instead of
boot_cpu_data.
No functionality change.
Signed-off-by: Borislav Petkov <bp@suse.de>
On newer models, support has been included for upto 4 DCT's, however,
only DCT0 and DCT3 are currently configured (cf BKDG Section 2.10).
Also, the routing DRAM Requests algorithm is different for F15h M30h.
Thus it is cleaner to use a brand new function rather than adding quirks
to the more generic f1x_match_to_this_node(). Refer to "2.10.5 DRAM
Routing Requests" in the BKDG for further info.
Tested on Fam15h M30h with ECC turned on using mce_amd_inj facility and
verified to be functionally correct.
While at it, verify if erratum workarounds for E505 and E637 still hold.
From email conversations within AMD, the current status of the errata
is:
* Erratum 505: fixed in model 0x1, stepping 0x1 and later.
* Erratum 637: not fixed.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Cleanups, corrections ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Make a local function static in order to fix the following sparse
warning:
drivers/edac/x38_edac.c:252:14: warning: symbol 'x38_map_mchbar' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
[ Boris: Correct commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>
This local symbol is used only in this file.
Fix the following sparse warnings:
drivers/edac/i3200_edac.c:264:14: warning: symbol 'i3200_map_mchbar' was not declared. Should it be static?
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
It can happen that configurations are running in a single-channel mode
even with a dual-channel memory controller, by, say, putting the DIMMs
only on the one channel and leaving the other empty. This causes a
problem in init_csrows which implicitly assumes that when the second
channel is enabled, i.e. channel 1, the struct dimm hierarchy will be
present. Which is not.
So always allocate two channels unconditionally.
This provides for the nice side effect that the data structures are
initialized so some day, when memory hotplug is supported, it should
just work out of the box when all of a sudden a second channel appears.
Reported-and-tested-by: Roger Leigh <rleigh@debian.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
The usage of strict_strtol() is not preferred, because strict_strtol()
is obsolete. Thus, kstrtol() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull MIPS updates from Ralf Baechle:
"MIPS updates:
- All the things that didn't make 3.10.
- Removes the Windriver PPMC platform. Nobody will miss it.
- Remove a workaround from kernel/irq/irqdomain.c which was there
exclusivly for MIPS. Patch by Grant Likely.
- More small improvments for the SEAD 3 platform
- Improvments on the BMIPS / SMP support for the BCM63xx series.
- Various cleanups of dead leftovers.
- Platform support for the Cavium Octeon-based EdgeRouter Lite.
Two large KVM patchsets didn't make it for this pull request because
their respective authors are vacationing"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (124 commits)
MIPS: Kconfig: Add missing MODULES dependency to VPE_LOADER
MIPS: BCM63xx: CLK: Add dummy clk_{set,round}_rate() functions
MIPS: SEAD3: Disable L2 cache on SEAD-3.
MIPS: BCM63xx: Enable second core SMP on BCM6328 if available
MIPS: BCM63xx: Add SMP support to prom.c
MIPS: define write{b,w,l,q}_relaxed
MIPS: Expose missing pci_io{map,unmap} declarations
MIPS: Malta: Update GCMP detection.
Revert "MIPS: make CAC_ADDR and UNCAC_ADDR account for PHYS_OFFSET"
MIPS: APSP: Remove <asm/kspd.h>
SSB: Kconfig: Amend SSB_EMBEDDED dependencies
MIPS: microMIPS: Fix improper definition of ISA exception bit.
MIPS: Don't try to decode microMIPS branch instructions where they cannot exist.
MIPS: Declare emulate_load_store_microMIPS as a static function.
MIPS: Fix typos and cleanup comment
MIPS: Cleanup indentation and whitespace
MIPS: BMIPS: support booting from physical CPU other than 0
MIPS: Only set cpu_has_mmips if SYS_SUPPORTS_MICROMIPS
MIPS: GIC: Fix gic_set_affinity infinite loop
MIPS: Don't save/restore OCTEON wide multiplier state on syscalls.
...
Add a new error signature for Family 15h, models 30h-3fh. Patch has been
tested on Fam15h using mce_amd_inj facility and has been verified to
work correctly.
Signed-off-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
[ cleanup commit message and error string ]
Signed-off-by: Borislav Petkov <bp@suse.de>
The usage of strict_strtoul() is not preferred, because strict_strtoul()
is obsolete. Thus, kstrtoul() should be used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Ever since commit 45f035ab9b ("CONFIG_HOTPLUG should be always on"),
it has been basically impossible to build a kernel with CONFIG_HOTPLUG
turned off. Remove all the remaining references to it.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix yet another issue caught by 8f46baaa7e ("base: core: WARN() about
bogus permissions on device attributes").
Signed-off-by: Borislav Petkov <bp@suse.de>
I get the following warning on boot:
------------[ cut here ]------------
WARNING: at drivers/base/core.c:575 device_create_file+0x9a/0xa0()
Hardware name: -[8737R2A]-
Write permission without 'store'
...
</snip>
Drilling down, this is related to dynamic channel ce_count attribute
files sporting a S_IWUSR mode without a ->store() function. Looking
around, it appears that they aren't supposed to have a ->store()
function. So remove the bogus write permission to get rid of the
warning.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: <stable@vger.kernel.org> # 3.[89]
[ shorten commit message ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull edac fixes from Mauro Carvalho Chehab:
"Two edac fixes:
- i7300_edac currently reports a wrong number of DIMMs when the
memory controller is in single channel mode
- on some Sandy Bridge machines, the EDAC driver bails out as one of
the PCI IDs used by the driver is hidden by BIOS. As the driver
uses it only to detect the type of memory, make it optional at the
driver"
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac:
edac: sb_edac.c should not require prescence of IMC_DDRIO device
i7300_edac: Fix memory detection in single mode
The Sandy Bridge EDAC driver uses a register in the IMC_DDRIO CSR
space to determine the type of DIMMs (registered or unregistered).
But this device does not exist on some single socket Sandy Bridge
servers. While the type of DIMMs is nice to know, it is not essential
for this driver's other functions. So it seems harsh to have it
refuse to load at all when it cannot find this device.
Make the check for this device be optional. If it isn't present
just report the memory type as "MEM_UNKNOWN".
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code to handle DRAM ECC errors decoding for Fam16h.
Tested on Fam16h with ECC turned on using the mce_amd_inj facility and
works fine.
Signed-off-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
[ Boris: cleanups and clarifications ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Both mci.mem_is_per_rank and mci.csbased denote the same thing: the
memory controller is csrows based. Merge both fields into one.
There's no need for the driver to actually fill it, as the core detects
it by checking if one of the layers has the csrows type as part of the
memory hierarchy:
if (layers[i].type == EDAC_MC_LAYER_CHIP_SELECT)
per_rank = true;
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
We were filling the csrow size with a wrong value. 16a528ee39 ("EDAC:
Fix csrow size reported in sysfs") tried to address the issue. It fixed
the report with the old API but not with the new one. Correct it for the
new API too.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
[ make it a per-csrow accounting regardless of ->channel_count ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull EDAC fixes and ghes-edac from Mauro Carvalho Chehab:
"For:
- Some fixes at edac drivers (i7core_edac, sb_edac, i3200_edac);
- error injection support for i5100, when EDAC debug is enabled;
- fix edac when it is loaded builtin (early init for the subsystem);
- a "Firmware First" EDAC driver, allowing ghes to report errors via
EDAC (ghes-edac).
With regards to ghes-edac, this fixes a longstanding BZ at Red Hat
that happens with Nehalem and Sandy Bridge CPUs: when both GHES and
i7core_edac or sb_edac are running, the error reports are
unpredictable, as both BIOS and OS race to access the registers. With
ghes-edac, the EDAC core will refuse to register any other concurrent
memory error driver.
This patchset moves the ghes struct definitions to a separate header
file (include/acpi/ghes.h) and adds 3 hooks at apei/ghes.c to
register/unregister and to report errors via ghes-edac. Those changes
were acked by ghes driver maintainer (Huang)."
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (30 commits)
i5100_edac: convert to use simple_open()
ghes_edac: fix to use list_for_each_entry_safe() when delete list items
ghes_edac: Fix RAS tracing
ghes_edac: Make it compliant with UEFI spec 2.3.1
ghes_edac: Improve driver's printk messages
ghes_edac: Don't credit the same memory dimm twice
ghes_edac: do a better job of filling EDAC DIMM info
ghes_edac: add support for reporting errors via EDAC
ghes_edac: Register at EDAC core the BIOS report
ghes: add the needed hooks for EDAC error report
ghes: move structures/enum to a header file
edac: add support for error type "Info"
edac: add support for raw error reports
edac: reduce stack pressure by using a pre-allocated buffer
edac: lock module owner to avoid error report conflicts
edac: remove proc_name from mci structure
edac: add a new memory layer type
edac: initialize the core earlier
edac: better report error conditions in debug mode
i5100_edac: Remove two checkpatch warnings
...
This removes an open coded simple_open() function and
replaces file operations references to the function
with simple_open() instead.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since we will remove items off the list using list_del() we need
to use a safe version of the list_for_each_entry() macro aptly named
list_for_each_entry_safe().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the current version of CPER, there's no way to associate an
error with the memory error. So, the error location in EDAC
layers is unused.
As CPER has its own idea about memory architectural layers, just
output whatever is there inside the driver's detail at the RAS
tracepoint.
The EDAC location keeps untouched, in the case that, in some future,
we could actually map the error into the dimm labels.
Now, the error message:
[ 72.396625] {1}[Hardware Error]: Hardware error from APEI Generic Hardware Error Source: 0
[ 72.396627] {1}[Hardware Error]: APEI generic hardware error status
[ 72.396628] {1}[Hardware Error]: severity: 2, corrected
[ 72.396630] {1}[Hardware Error]: section: 0, severity: 2, corrected
[ 72.396632] {1}[Hardware Error]: flags: 0x01
[ 72.396634] {1}[Hardware Error]: primary
[ 72.396635] {1}[Hardware Error]: section_type: memory error
[ 72.396637] {1}[Hardware Error]: error_status: 0x0000000000000400
[ 72.396638] {1}[Hardware Error]: node: 3
[ 72.396639] {1}[Hardware Error]: card: 0
[ 72.396640] {1}[Hardware Error]: module: 0
[ 72.396641] {1}[Hardware Error]: device: 0
[ 72.396643] {1}[Hardware Error]: error_type: 18, unknown
[ 72.396666] EDAC MC0: 1 CE reserved error (18) on unknown label (node:3 card:0 module:0 page:0x0 offset:0x0 grain:0 syndrome:0x0 - status(0x0000000000000400): Storage error in DRAM memory)
Is properly represented on the trace event:
kworker/0:2-584 [000] .... 72.396657: mc_event: 1 Corrected error: reserved error (18) on unknown label (mc:0 location👎-1:-1 address:0x00000000 grain:1 syndrome:0x00000000 APEI location: node:3 card:0 module:0 status(0x0000000000000400): Storage error in DRAM memory)
Tested on a 4 sockets E5-4650 Sandy Bridge machine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide a better infrastructure for printk's inside the driver:
- use edac_dbg() for debug messages;
- standardize the usage of pr_info();
- provide warning about the risk of relying on this
driver.
While here, changes the size of a fake memory to 1 page. This is
as good or as bad as 1000 pages, but it is easier for userspace to
detect, as I don't expect that any machine implementing GHES would
provide just 1 page available ;)
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conflicts:
drivers/edac/ghes_edac.c
Instead of just faking a random value for the DIMM data, get
the information that it is available via DMI table.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now that the EDAC core is capable of just forward the errors via
the userspace API, add a report mechanism for the GHES errors.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Register GHES at EDAC MC core, in order to avoid other
drivers to also handle errors and mangle with error data.
The edac core will warrant that just one driver will be used,
so the first one to register (BIOS first) will be the one that
will be reporting the hardware errors.
For now, the EDAC driver does nothing but to register at the
EDAC core, preventing the hardware-driven mechanism to
interfere with GHES.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Aravind Gopalakrishnan