get_tx_stats() will be removed from mac80211.
Compile-tested only.
Cc: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to queue a work struct from
within a work struct, just move the code to
execute directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
In iwlagn the support for spectrum measurement command has been
disabled since v2.6.29 without any requests for it. In addition to this
when this command is indeed enabled it has been found to trigger firmware
SYSASSERT on at least 4965 and 5100 hardware (see
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1952 ). Since then
this code has been bitrotting and cannot just be enabled without porting.
Remove support for spectrum measurement command from iwlagn. It can be
added back if there is a future need and the firmware problem it triggers
has been fixed. Support for the spectrim measurement notification remains
as it has been enabled all the time.
In addition to this remove the 3945 spectrum measurement command Kconfig
option and make this command always supported. The code added by this
enabling is minimal and only run when user triggers a spectrum measurement
request via sysfs.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support to configure missed beacon threshold, by default, if receive
"missed beacon" notification from uCode and has more than 5 consecutive
beacon missed, then perform sensitivity calibration; with this change,
allow user to adjust the missed beacon threshold from debugfs in case
more sensitivity calibration required for better performance in noisy
environment
The default value (=5) should be good enough for the normal condition,
but for very noisy environment, more sensitivity calibration could help
improve the throughput, so by setting the missed beacon threshold to
lower number, user might experience better performance result.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When dumping event log in debugfs, iwl_dump_nic_event_log()
should return the correct error code instead of let the calling
function makes it own assumption.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature enables the on-screen uCode event log dump. The original
method will append the event log to syslog; with this capability,
we also enable the user to write script to capture the
events which provide additional flexibility to help uCode debugging
Method
1) change to debugfs directory (sys/kernel/debug/phyX/iwlagn/data)
2) #cat log_event
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recent powersaving work resulted in power management ops being called
during EEPROM initialization. The lock used by these functions is not
initialized at this time. Ensure lock is initialized before it is used.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we see from http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2125
that power saving does not work well on 3945. Since then power saving has
also been connected with association problems where an AP deathenticates a
3945 after it is unable to transmit data to it - this happens when 3945
enters power savings mode.
Disable power save support until issues are resolved.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trigger event log dumping from debugfs, the entire event log
should be dumped and the size should match the number of events being
dump.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In iwlwifi, priv->alloc_rxb_page is used to keep track of the Rx
pages allocated by the driver. This cleans up the page free routines
by introducing __iwl_free_pages/iwl_free_pages so that the accounting
is more accurate and less error prone. This also fixes two instances where
the counter was not updated.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver version number is a remnant from when there was an out-of-tree
iwlwifi driver. Now that the driver forms part of kernel source we do not
need a separate driver version. Instead, we now use the kernel version as
driver version. We maintain the previous tags used to indicate which
components the driver has been compiled with.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the process of improving uCode event logging capability, the new
implementation was introduced without removing the existing
implementation. The event log will be dumped to dmesg twice.
Remove the old implementation to only log the event once upon sys
assert or request by user.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help iwlagn uCode debugging, event log will dump to syslog when driver
detect uCode error occurred, but this only happen when compile with
CONFIG_IWLWIFI_DEBUG and debug flag is enabled; which is not always
the case. Also, there is another problem, if the flag is set, the entire
event log buffer will be dump to syslog, it can flood the syslog and
make it very difficult to debug the problem.
Change the default to only dump last 20 entries of event log to syslog
unless the following condition meets:
1. both compile with CONFIG_IWLWIFI_DEBUG and debug flag
is enabled, and then dump the entire event buffer to syslog.
2. dump event log request from debugfs
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Acked-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've accumulated a number of options for wiphys
which make more sense as flags as we keep adding
more. Convert the existing ones.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Power-saving logic will not re-issue a POWER_TABLE_CMD if a new command
matches the prior one. This can be bad if we re-start the device due to
e.g. uCode error; the new POWER_TABLE_CMD (required to invoke power-saving)
may match the prior POWER_TABLE_CMD issued before the uCode error.
Ensure the POWER_TABLE_CMD is sent to device when uCode is up.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When issue REPLY_STATISTICS_CMD to uCode, two possible flag
can be set in the configuration flags
bit 0: Clear statistics
0: Do not clear Statistics counters
1: Clear to zero Statistics counters
Allow "clear" parameter to be set from the caller.
Add debugfs file to clear the statistics counters to help monitor and
debug the uCode behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add txq_id info to "Tx queue requesting wakeup" debug message
Add "Rx queue requesting wakeup" debug message
Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it. Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()! Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().
Join a couple of lines that had unneeded line returns.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.
Grab/release NIC access before/after entire read sequence, rather than for
each read individually.
After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.
Sanity-check capacity and next_entry values and limit to reasonable size dump.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To save power, don't run apm_ops.init() until needed at "up" time.
EEPROM (5000 and earlier devices) may be read without running apm_ops.init(),
but OTP reads (6000 and newer devices) require a powered-up chip.
Therefore, remove apm_ops.init() from the general path in XXXX_pci_probe(),
and call it only if device uses OTP. Once done with OTP read, call
apm_ops.stop() to reset chip and save power until "up" time comes around.
NOTE: This patch depends on removal of priv->lock from iwl_apm_stop();
lock does not get initialized until later in flow. See patch
"remove unneeded locks from apm_stop()".
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By setting the firmware version in wiphy it is possible to obtain this
information via ethtool. Some examples,
# ethtool -i wlan1
driver: iwlagn
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 228.57.2.23
bus-info: 0000:03:00.0
# ethtool -i wlan0
driver: iwl3945
version: 2.6.32-rc5-wl-56840-g26d8540
firmware-version: 15.28.2.8
bus-info: 0000:02:00.0
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add unconditional call to apm_ops.stop() to reset device to low power state
when unloading driver. Some paths have existed to unload driver *without*
resetting device, therefore some errors have persisted through multiple
load/unload cycles, until the whole platform gets rebooted; this is an
attempt to remedy some of those situations. Sorry, I can't seem to find
a bughost.org bug that specifically has these symptoms, but I had it happen
recently here.
Note that this will *not* fix situations in which the PCI express bus has
crashed (evidenced by register reads showing "0xffffffff"), e.g. bughost.org
1855 and 2096; device is unreachable from driver in those cases.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For notification packets and SKBs that fail to rx correctly, add
them back into the rx_free list so that the pages can be reused
later. This avoids allocating new rx pages unnecessarily.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the paged rx patch (4854fde2), I introduced a bug that could possibly
touch an already freed page. It is fixed by avoiding the access in this
patch. I've also added some comments so that other people touching the
code won't make the same mistake. In the future, if we cannot avoid
access the page after being handled to the upper layer, we can use
get_page/put_page to handle it. For now, it's just not necessary.
It also fixed a debug message print bug reported by Stanislaw Gruszka
<sgruszka@redhat.com>.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This switches the iwlwifi driver to use paged skb from linear skb for Rx
buffer. So that it relieves some Rx buffer allocation pressure for the
memory subsystem. Currently iwlwifi (4K for 3945) requests 8K bytes for
Rx buffer. Due to the trailing skb_shared_info in the skb->data,
alloc_skb() will do the next order allocation, which is 16K bytes. This
is suboptimal and more likely to fail when the system is under memory
usage pressure. Switching to paged Rx skb lets us allocate the RXB
directly by alloc_pages(), so that only order 1 allocation is required.
It also adjusts the area spin_lock (with IRQ disabled) protected in the
tasklet because tasklet guarentees to run only on one CPU and the new
unprotected code can be preempted by the IRQ handler. This saves us from
spawning another workqueue to make skb_linearize/__pskb_pull_tail happy
(which cannot be called in hard irq context).
Finally, mac80211 doesn't support paged Rx yet. So we linearize the skb
for all the management frames and software decryption or defragmentation
required data frames before handed to mac80211. For all the other frames,
we __pskb_pull_tail 64 bytes in the linear area of the skb for mac80211
to handle them properly.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the ununsed variable data_retry_limit
from priv.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
3945 and 4965 share the functionality for setting RTS and CTS to
the tx_cmd. Unify these functions and move the common
functionality to core.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of always allocate the max number of tx queue structure,
use dynamic allocation based on the number of queues in device
configuration. With these changes, device does not have to allocate more
memory than the h/w can support.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_power_initialize() initializes driver data (not device hardware), and does
not need to execute more than once (when the driver initializes). Therefore, it
does not belong in iwl3945_apm_init(), which initializes hardware, and may run
more than once.
Move it to iwl3945_pci_probe(), where it will run only once. This agrees
with similar placement in iwl-agn.c's iwl_pci_probe(), although placement
under "services" seemed more appropriate than under "mac80211".
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl3945_rfkill_poll() has been silently calling wiphy_rfkill_set_hw_state()
every 2 seconds, regardless of whether hardware RF KILL switch changed state.
Call wiphy_rfkill_set_hw_state() only when RFKILL switch changes.
Add IWL_DEBUG_RF_KILL log message and documentation.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that we're unconditionally using apm_ops.stop() to reset and power-down
the device in __iwl3945_down(), the apm_ops.reset() is redundant. Removing
this call will also allow us to remove iwl3945_apm_reset().
Remove unneeded iwl_clear_bit(CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ) because
this bit will be set again very soon in iwl3945_hw_txq_ctx_stop() and other
following calls.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases (e.g. when mac80211 calls iwl_mac_stop() for suspend or user
no longer wants device active), device has not been going into low power state
via __iwl_down(). apm_ops.reset() does not put device into low power state;
instead it resets the device, then puts it into a powered-up state ready to be
re-loaded with uCode and re-started. This has needlessly warmed up user's
laptops and drained batteries.
With current architecture in which mac80211 controls device up/down (including
resetting device after firmware errors), there is no need for apm_ops.reset()
any more; apm_ops.reset() is basically a combination of apm_ops.stop() and
apm_ops.init().
Instead, __iwl_down() now unconditionally places the device into a low-power
state via apm_ops.stop(). Device may be re-started via __iwl_up() calling
apm_ops.init() as soon as it may be needed (e.g. quickly for firmware errors),
but in the meantime, device will stop wasting energy.
Note that, even in this low power state, if driver re-enables interrupts,
the device retains the ability to sense the hardware RF-KILL switch, and
(except for 3945) interrupt the host when it changes.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Need to free the dynamic allocated memory before ieee80211_free_hw();
once call ieee80211_free_hw(), should not reference to "priv" data
structure.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
The iwlwifi drivers have LED blinking requirements that
mac80211 cannot fulfill due to the use of just a single
LED instead of different ones for TX, RX, radio etc.
Instead, the single LED blinks according to transfers
and is solid on the rest of the time. As such, having
LED class devices registered that mac80211 triggers are
connected to is pointless as we don't use the triggers
anyway.
Remove all the useless code and add hooks into the
driver itself. At the same time, make the LED code
abstracted so the core code that determines blink rate
etc. can be shared between 3945 and agn in iwlcore.
At the same time, the fact that we removed the use of
the mac80211 LED triggers means we can also remove the
IWLWIFI_LEDS Kconfig symbol since the LED support is
now self-contained.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to have an easier way to debug issues, create
trace events (using the ftrace framework) that will
allow us to follow exactly what the driver is doing
with the device.
The text format isn't all that useful, but the binary
format can also be obtained easily via debugfs and
then analysed on the fly or offline with debugging
tools.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ever since Johannes' "iwlwifi: improve scan support" iwlwifi
no longer needs any of lib80211's functions or definitions.
This patch updates iwlwifi's Kconfig _selections_ and
removes all left lib80211.h inclusions from the source files.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of hardcode module parameter's permissions, use pre-defined.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When hardware or uCode problem occurs driver captures significant
information from device to enable debugging. The format of this information
is different between 3945 and 4965 and later devices, yet currently the
3945 uses the 4965 and later format. Fix this by adding a new library call
that is initialized to the correct formatting routine based on device.
This moves the iwlagn event and error log handling back to iwl-agn.c to
make it part of iwlagn module.
Also remove the 3945 sysfs file that triggers dump of event log - there is
already a debugfs file that can do it for all drivers.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replenishment of receive buffers is done in the tasklet handling
received frames as well as in a workqueue. When we are in the tasklet
we cannot sleep and thus attempt atomic skb allocations. It is generally
not a big problem if this fails since iwl_rx_allocate is always followed
by a call to iwl_rx_queue_restock which will queue the work to replenish
the buffers at a time when sleeping is allowed.
We thus add the __GFP_NOWARN to the skb allocation in iwl_rx_allocate to
reduce the noise if such an allocation fails while we still have enough
buffers. We do maintain the warning and the error message when we are low
on buffers to communicate to the user that there is a potential problem with
memory availability on system
This addresses issue reported upstream in thread "iwlagn: order 2 page
allocation failures" in
http://thread.gmane.org/gmane.linux.kernel.wireless.general/39187
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Kalle Valo