For USB gadget on port A (device mode):
- pin PA31 is configured as an input GPIO which triggers an interrupt when
vbus is detected on USB port A.
- pin PB9 is configured as an output GPIO and set to low level so the
board doesn't supply vbus to USB port A.
For USB host:
- pin PB10 is configured as an output GPIO and is active at high level.
The ohci driver will activate this pin so the board supplies vbus to USB
port B.
- pin PB9 should be configured as an output GPIO and active at high level
to use to USB port A in host mode (conflicts with USB gadget).
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
MAC is connected to a PHY in MII mode.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW063aAAoJEJzN3yze689ThbEQAJbn/pHDRlw7u8NUiNfRbQWd
uf//IiF2tbJ8eGpCvYIh+dLSlFbFzn3qIETAXJjZ7NfqYpgZsDAwFoMnVF6FfcMG
o2GAVGnUaXge+s+r5PkIwaCRh9LWO5iHJTHjykonhXaKKO4NrHxtsspo/We6Kth4
kmsrmovWd1CvnsvNZJXFSFf37z2eZFG+RYyrveKhFiTlliqyX/DT/RgOqPPPa0UC
9FBXrQ67ibKymX2qYLb5USQnppNFrnzDCacJBiFc2z/kpFFkII7XDrJVogn2JJfZ
M4uQ8JWqBhjrh2yU1FtQ7vuBfk8/Ssbvbp7J+roHJZGwe6AjVY2d3WCRGMLy/fFh
rCfsVvCrwupPVsVj50yTVyEJ0kiDZ9tz3rboWxfuTv/AtRxpUm9gMZ6yE/g2cBl4
RnkYp9dE/Kmu5BaaJZm9yIlHOEgQD/nhXGWm+BdgJBPB2+qAA0D7VPav0Fazjr8O
fN/kyaFHZ5jxSynGVCTsbfD8cJiVWdRzyxwoeXllvGqxwcdgHzX7LrTXrDkRtgC3
5r1B6qgm0kpPxYotrfPI+vAQnR5PGYBa0L4mwXha1rnonwI39QIgg76ZsHyy6k2u
rwGpT3zQmxFs9puf6pFAGmFCaLd1nb5r7FrslkZsn4gG100Gi0ONRRyN6Jx7f7W2
x/EvDnRYTM/pNpNp04Yb
=Zxas
-----END PGP SIGNATURE-----
Merge tag 'extcon-next-for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-testing
Chanwoo writes:
Update extcon for 4.6
Detailed description for patchset:
1. Add new EXTCON_CHG_USB_SDP type
- SDP (Standard Downstream Port) USB Charging Port
means the charging connector.a
2. Add the VBUS detection by using GPIO on extcon-palmas
- Beaglex15 board uses the extcon-palmas driver
But, beaglex15 board need the GPIO support for VBUS
detection.
3. Fix the minor issue of extcon drivers
In the final versions of the Porter board (called "PORTER_C") Renesas
decided to get rid of the Maxim Integrated MAX3355 OTG chip and didn't
add any other provision to differ the host/gadget mode, so we'll have to
remove no longer valid "renesas,enable-gpio" property from the HS-USB
device node. Hopefully, the earlier revisions of the board were never
seen in the wild...
Fixes: c794f6a09a ("ARM: shmobile: porter: add HS-USB DT support")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds support for the volume and gesture keys, using TWL4030 keypad.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 5fcc673067.
The binding may need to change pending related hwmod comments,
so reverting as requested by Paul Walmsley <paul@pwsan.com>.
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] dm814x TRM: SPRUGZ8F: 11.2.4.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add Ethernet support (Synopsys MAC IP 3.50a) on stm32f429 SOC.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
The polarity of the gpio buttons is defined to '0' which is
active high. The buttons are active low though which has been verified by
testing it and by looking into the schematics. While at it use
defines rathers than numbers for the key codes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Both nodes are required to access NAND Flash memory. Additional
settings will be necessary at the board level to use it.
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The dmas/dma-names properties are added to the UART nodes. Note that additional
properties are needed to enable them at the board level: check bindings for
details.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
All pinctrl nodes for the Atmel pinctrl controller need to have their
bias configuration explicitly defined. Otherwise, the pinctrl mapping
is not valid.
It works for now as the pinctrl driver proceeds even with invalid
mappings, but this can become an issue, if the pinctrl driver starts
to require valid mappings. Additionally, the pin is not protected from
being remapped later by an other driver.
There is an external 1kOhms pull-up to 3.3V, so no bias is required on
the Ethernet PHY's interrupt line.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
After adding cpufreq-dt support to Exynos542x, the Odroid XU3-Lite can
be easily overheated when launching eight CPU-intensive tasks:
thermal thermal_zone3: critical temperature reached(121 C),shutting down
This seems to be specific to Odroid XU3-Lite board which officially
supports lower frequencies than regular XU3 or XU4. When working at
maximum CPU speed (1800 MHz big and 1300 MHz LITTLE) in warmer place for
longer time, the fan fails to cool down the board and it reaches
critical temperature.
Add CPU cooling to Exynos5422/5800 to fix this issue. When reaching last
interrupt-driven trip-point (70 degrees of Celsius) start passive
cooling in polling mode (slowing CPU by 2 steps). When reaching 85
degrees of Celsius, start slowing even more, down to 600 MHz.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
On Exynos5422 and Exynos5800 we support 12 cpufreq steps (200-1300 MHz) for LITTLE
and 18 steps for big core (200-1700 MHz). Add respective cooling cells.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
On Exynos5420 we support 8 cpufreq steps (600-1300 MHz) for LITTLE and
12 steps for big core (700-1800 MHz). Add respective cooling cells.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
This is a minor cycle with :
- cleanup fixes from Arnd, mainly build oriented and sparse type ones
- dma fixes for requestors above 32 (impacting mainly camera driver)
- some minor cleanup on pxa3xx device-tree side
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lBYC
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.6' of https://github.com/rjarzmik/linux into next/soc
Merge "pxa changes for v4.6 cycle" from Robert Jarzmik:
This is a minor cycle with :
- cleanup fixes from Arnd, mainly build oriented and sparse type ones
- dma fixes for requestors above 32 (impacting mainly camera driver)
- some minor cleanup on pxa3xx device-tree side
* tag 'pxa-for-4.6' of https://github.com/rjarzmik/linux:
dmaengine: pxa_dma: fix the maximum requestor line
ARM: pxa: add the number of DMA requestor lines
dmaengine: mmp-pdma: add number of requestors
dma: mmp_pdma: Add the #dma-requests DT property documentation
ARM: pxa: pxa3xx device-tree support cleanup
ARM: pxa: don't select RFKILL if CONFIG_NET is disabled
ARM: pxa: fix building without IWMMXT
ARM: pxa: move extern declarations to pm.h
ARM: pxa: always select one of the two CPU types
ARM: pxa: don't select GPIO_SYSFS for MIOA701
ARM: pxa: mark unused eseries code as __maybe_unused
ARM: pxa: mark spitz_card_pwr_ctrl as __maybe_unused
ARM: pxa: define clock registers as __iomem
Add PWMSS device tree nodes for DRA7 SoC family and add documentation
for dt bindings.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
tbclk is used by ehrpwm to generate PWM waveform on DRA7 SoC. Add Linux
clock to control ehrpwm tbclk.
The TRM says, tbclk is derived from SYSCLKOUT. SYSCLKOUT is nothing but
ehrpwm functional clock derived from the gateable interface and
functional clock of PWMSS(l4_root_clk_div).
Refer AM57x TRM SPRUHZ6[1], October 2014, Table 29-4 and Section 29.2.2.1,
Table 29-19 and the NOTE at the end of the table.
[1] www.ti.com/lit/ug/spruhz6/spruhz6.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- a single fix for nand dmaengine node
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=4uk1
-----END PGP SIGNATURE-----
Merge tag 'pxa-dt-4.6' of https://github.com/rjarzmik/linux into next/dt
Merge pxa dt for v4.6 from Robert Jarzmik:
This device-tree pxa update brings :
- a single fix for nand dmaengine node
* tag 'pxa-dt-4.6' of https://github.com/rjarzmik/linux:
ARM: dts: pxa: fix dma engine node to pxa3xx-nand
Quite a few changes, among which:
- Support for the A83t
- Support for the eMMC DDR on a few boards
- Support for the OTG controller on a few boards
- New boards: Itead Ibox, Cubietruck plus, Homlet v2, Lamobo R1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=CJtp
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT Additions for 4.6" from Maxime Ripard:
Quite a few changes, among which:
- Support for the A83t
- Support for the eMMC DDR on a few boards
- Support for the OTG controller on a few boards
- New boards: Itead Ibox, Cubietruck plus, Homlet v2, Lamobo R1
* tag 'sunxi-dt-for-4.6' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (34 commits)
ARM: dts: sun8i: Add leds and switch on Orangepi Plus boards
ARM: dts: sun8i: Add ir receiver nodes to H3 dtsi
ARM: dts: sun8i-h3: Add R_PIO controller node to the dtsi
dts: sun8i-h3: Add APB0 related clocks and resets
ARM: dts: sun7i: Add dts file for the lamobo-r1 board
ARM: dts: sun4i: Enable USB DRC on Hyundai-a7hd
ARM: dts: sun4i: Enable USB DRC on the MK802
ARM: dts: sun8i: q8-common: Add AXP223 PMIC device and regulator nodes
ARM: dts: sun8i: sinlinx-sina33: Add AXP223 PMIC device and regulator nodes
ARM: dts: sun7i: Enable USB DRC on Olimex A20 EVB
ARM: dts: sun7i: Enable USB DRC on MK808C
ARM: dts: sunxi: Fix #interrupt-cells for PIO in H3
ARM: dts: sun8i-a83t: Correct low speed oscillator clocks
ARM: dts: sun9i: a80-optimus: Remove i2c3 and uart4
ARM: dts: sun4i: Itead Iteaduino to use common code
ARM: dts: sun7i: Add Itead Ibox support
ARM: dts: sunxi: Add sunxi-itead-core-common.dtsi
ARM: dts: sun9i: cubieboard4: Enable hardware reset and HS-DDR for eMMC
ARM: dts: sun9i: a80-optimus: Enable hardware reset and HS-DDR for eMMC
ARM: dts: sun9i: Include SDC2_RST pin in mmc2_8bit_pins
...
DRA7 SoC has the capability to support DDR memory upto 4GB. In order to
represent this in memory dt node, the address-cells and size cells
should be 2. So, changing the address-cells and size-cells to 2 and
updating the memory nodes accordingly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Reorder Ethernet node on Armada 38x SoCs
- Add device tree for buffalo linkstation ls-gl
- Use the more accurate armada-370-sata string for SATA on Armada 375
- Add NAND description to Armada 370 DB and Armada XP DB
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlbQXKwACgkQCwYYjhRyO9VVYwCgpjGDDOuqbNWtj5NI3TS9gHsI
FLkAn1kS66eVLwf+0ptrOtu8nsu9mLql
=O+/a
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.6-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu dt for 4.6 (part 2)" from Gregory CLEMENT:
- Reorder Ethernet node on Armada 38x SoCs
- Add device tree for buffalo linkstation ls-gl
- Use the more accurate armada-370-sata string for SATA on Armada 375
- Add NAND description to Armada 370 DB and Armada XP DB
* tag 'mvebu-dt-4.6-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: mvebu: add NAND description to Armada 370 DB and Armada XP DB
ARM: dts: armada-375: use armada-370-sata for SATA
ARM: dts: orion5x: add device tree for buffalo linkstation ls-gl
ARM: dts: orion5x: split linkstation lswtgl into common and device parts
ARM: dts: armada-38x: add reference to ETH connectors for A385-AP
ARM: dts: armada-38x: change order of ethernet DT nodes on Armada 38x
ARM: dts: orion5x: fix the missing mtd flash on linkstation lswtgl
ARM: dts: kirkwood: use unique machine name for ds112
This adds support for USB OTG on the Optimus Black.
The HSUSB0 interface is connected to the TWL4030 USB PHY.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LG Optimus Black codename sniper is a smartphone that was designed and
manufactured by LG Electronics (LGE) and released back in 2011.
It is using an OMAP3630 SoC, GP version.
This adds devicetree support for the device, with only a few basic features
supported, such as debug uart, i2c, internal emmc and external mmc.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device tree node entry for DAC peripheral on Vybrid SoC.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The backlinks are already there since commit 4520e69238 ("ARM: dts:
imx6qdl: Add IPU DI ports and endpoints, move imx-drm node to dtsi")
and were moved by commit 70c2652c6c ("ARM: dts: imx6qdl: Move existing
MIPI DSI ports into a new 'ports' node"), but the links from IPU2 DI0/1
to the MIPI DSI mux are missing. Fix this.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Advantech has 3 carrier boards (B450v3, B650v3, B850v3) which use
the Advantech BA-16 module (based on iMX6D). This file has the
devicetree entries that are common to all 3 boards.
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For imx35, it needs three clocks to let the controller work,
the old code is wrong, and the usbmisc does not include
clock handling code any more.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
For imx25, it needs three clocks to let the controller work,
the old code is wrong, and usbmisc has not included clock
handling code any more.
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds the device node for the i.MX6UL keypad controller.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the device node for the i.MX6UL GPMI interface and the related
APBH DMA which is necessary for the GPMI to work properly.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add device nodes for the PWM uinits 1..4 which were missing in the
original commit for i.MX6UL support.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration. This is in sync with a recent change
(commit e2675266b3 "ARM: dts: imx6qdl: disable PWMs by default")
to other i.MX SoCs.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6UL GPT unit requires real clocks. Define the appropriate
clocks to make it work.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul.dtsi references the macro 'KEY_POWER' from
dt-bindings/input/input.h. Thus, move the include statement for this
file from imx6ul-14x14-evk.dts to imx6ul.dtsi itself.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the tsc node to keep the nodes sorted in ascending order by unit
address.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Pad DISPB2_SER_RS has no function DISP1_EXT_CLK.
The definition is obviusly a copy/paste error from
MX51_PAD_DISPB2_SER_RS__DISP1_PIN16.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Various pads are missing the input_sel offset and value. Fix this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
All Freescale Vybrid SoC include a Cortex-A5 core which supports
ARM's standard PMU (performance monitoring unit). Include the
monitoring unit into the Cortex-A5 base device tree vf500.dtsi.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Colibri standard does not define a pin for SD-Card write-
protection. Use the disable-wp property to indicate that there
is no physical WP line present.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers from SPI NOR Flashes.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the carrier boards 3.3V supply as fixed regulator. This allows
to specify the power supply for nodes like backlight.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Drop the fake simple-bus container 'regulators' and put the
regulators directly under the root node. This also makes the
artificial 'reg' properties superfluous. While at it, remove
the unnecessary regulator-always-on property and name the
regulators according to schematics.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign Ethernet clock parents explicitly. The Colibri VF61
uses the 50MHz Ethernet clock provided by PLL5.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Assign Ethernet clock parents explicitly. The VF610 Tower Board
uses the external Ethernet clock input which is connected to
a 50MHz clock.
The Vybrid SoC has two ethernet interfaces (fec0 and fec1) which
use the same clock source (VF610_CLK_ENET). Therefore this parent
configuration affects multiple consumer devices and need to be
specified in the clock provider node.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid the following warnings (example for usdhc2):
/soc/aips-bus@02100000/usdhc@02194000: voltage-ranges unspecified
sdhci-esdhc-imx 2194000.usdhc: could not get ultra high speed state,
work on normal mode
sdhci-esdhc-imx 2194000.usdhc: No vqmmc regulator found
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure SATA PHY transmit level, boost, attenuation and equalizer
parameters for long wire connections. TBS2910 contains a standard SATA
connector, so devices are typically connected with (longer) SATA cables.
And explicitly configuring these parameters avoids complaints about
"not specified" values in boot messages.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Downstream packages like Debian flash-kernel use
/proc/device-tree/model
to determine which dtb file to install.
Hence each dts in the Linux kernel should provide a unique model
identifier.
Commit 8536239e37 ("ARM: dts: Restructure imx6qdl-wandboard.dtsi for new
rev C1 board.")' created new files imx6dl-wandboard-revb1.dts and
imx6q-wandboard-revb1.dts but used the same model identifier as in
imx6dl-wandboard.dts and imx6q-wandboard.dts.
This patch provides unique model identifiers for revision B1 of
the Wandboard Dual and Wandbaord Quad.
The patch leaves imx6dl-wandboard.dts and imx6q-wandboard.dts unchanged
because it is not foreseeable if the same dts will valid for future
board revisions or not. Furthermore we should avoid unnecessary
changes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Uniwest evi is a portable electrical eddy current non-destructive
testing device.
Signed-off-by: Joshua Clayton <stillcompiling@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX6Quad Plus processor is an high performance SOC of i.MX6 family.
It has enhanced graphics performance and increased overall memory bandwidth
compared to i.MX6Q. Most of the design are same as i.MX6Quad/Dual, so code
for i.MX6Quad can be resued by this chip. The revision number is identied as
i.MX6Q Rev2.0, but actually it is a new chip, as we did many change to the
overall architecture.
This patch adds basic dtsi file support for the new i.MX6Quad Plus processor.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf610-twr.dts file to this combination.
CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf610-twr.dts
--CC: Chao Fu <B44548@freescale.com>
CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
--CC: Fugang Duan <B38611@freescale.com>
--CC: Jingchang Lu <b35083@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Bill Pringlemeir <bpringle@sympatico.ca>
Acked-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vf*colibri* files to this combination.
CCs were acquired using:
git shortlog -sne --no-merges arch/arm/boot/dts/vf*colibri*
Acked-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license.
The consensus is that a GPL/X11 dual-license should allow all necessary
uses, so relicense the vfxxx.dtsi, vf500.dtsi and vf610.dtsi files to
this combination.
CCs were acquired using (updated some email addresses, commented out
bouncing email addresses with --):
git shortlog -sne --no-merges arch/arm/boot/dts/vf???.dtsi
--CC: Chao Fu <B44548@freescale.com>
CC: Cosmin Stoica <cosminstefan.stoica@freescale.com>
CC: Frank Li <Frank.Li@freescale.com>
CC: Fugang Duan <B38611@freescale.com>
--CC: Huang Shijie <b32955@freescale.com>
--CC: Jingchang Lu <jingchang.lu@freescale.com>
--CC: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Cory Tusar <cory.tusar@pid1solutions.com>
Acked-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Yuan Yao <yao.yuan@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
LS1021a contains two PCIe controllers. The patch adds their node to
dts file.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add sound support in UDOO board DT file.
Signed-off-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add alias for FEC ethernet on Vybrid to allow bootloaders (like U-Boot)
patch-in the MAC address using this alias.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
PCIe reset signals are active low, and our GPIO for this is directly
connected to the PCIe reset. However, as the PCIe driver was not using
the flag, the specification of '0' flags (which means active high) had
not been noticed. Correct this oversight, and switch to using the
GPIO flag definitions instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use proper gpio flag definitions for GPIOs rather than using opaque
uninformative numbers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Avoid the following warning:
sdhci-esdhc-imx 2190000.usdhc: could not get ultra high speed state, work on normal mode
which occurs regularly at boot each time the SDHCI interface for the
Broadcom WiFi is probed at boot.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ENET_OUT is used as reference clock for the ethernet PHY on the Ka-Ro
TX6 modules. Specify this clock in DTB to let it be managed correctly
by the driver.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The reference clock for the SGTL5000 is generated by a 26MHz crystal
oscillator on the Ka-Ro electronics STK5 eval kits. Use the correct
frequency setting in DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch adds node i2c bus 3 to get the appropriate userland device
file. So for prototyping it's possible to experiment within userland.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The GW54xx can provide PWM4 out either the off-board backlight connector
or the off-board digital I/O connector. By default the pinmux routes it
to the backlight connector but this pinctl alternate provides documentation
for those who may want to change it.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Since uboot v2016.01-rc2, which supported basic psci for i.mx7d.
So imx7d's second core can be enabled by psci.
Without arch timer, every timer event will be boardcasted to each core.
arch timer has local timer irq for each core.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Though the keyboard and other driver will continue to support the legacy
"gpio-key,wakeup", "linux,wakeup" and "enable-sdio-wakeup" boolean
property to enable the wakeup source, "wakeup-source" is the new
standard binding.
This patch replaces all the legacy wakeup properties with the unified
"wakeup-source" property in order to avoid any futher copy-paste
duplication.
Cc: Sascha Hauer <kernel@pengutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds the remaining SAI instances SAI0, SAI1 and SAI3. All
instances are very similar, except that the DMA channel of SAI3
is available on MUX1 (compared to MUX0 for SAI0-SAI2). Also,
SAI3 has a slightly different memory map due to a deeper FIFO,
however in practice the current driver works for SAI3 fine.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 8ba671efdb.
As reported by kbuild test robot <fengguang.wu@intel.com>:
In file included from arch/arm/boot/dts/mt2701-evb.dts:16:0:
>> arch/arm/boot/dts/mt2701.dtsi:18:28: fatal error: mt2701-pinfunc.h: No such file or directory
#include "mt2701-pinfunc.h"
^
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since the switch from mmp_pdma to pxa_dma driver for pxa architectures,
the pxa_dma requires 2 arguments, namely the requestor line and the
requested priority.
Fix the only left device node which was still passing only one argument,
making the pxa3xx-nand driver misbehave in a device-tree configuration,
ie. failing all data transfers.
Fixes: c943646d1f ("ARM: dts: pxa: add dma engine node to pxa3xx-nand")
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Merge "Broadcom devicetree changes for 4.6" from Florian Fainelli:
This pull request contains Broadcom ARM-based SoCs Device Tree changes:
- Rafal adds a Device Tree for the D-Link DIR-885L router which is based on the
BCM47094 SoC similar to the BCM4709
- Simran adds proper audio clock Device Tree nodes to the Cygnus platforms
- Martin adds the auxiliary SPI controllers, makes the UART naming convention
more standard, and finally adds the auxiliary UART found in the BCM2835 to the
BCM2835 Device Tree
- Remi adds PWM clock support to the BCM2835 Device Tree
- Lubomir adds a Device Tree for the Raspberry Pi Model A
- Alexander adds Device Tree information for the Raspberry Pi USB power domain
- Dhananjay enables the GPIO-A controller for the Northstar Plus SoCs
- Jon fixes the PCIE Device Tree nodes by pulling them out of the bus-level node,
removes duplicate CPU definitions, adds PMU nodes, SP804 timers, and SP805 watchdog
to the Northstar Plus SoCs
* tag 'arm-soc/for-4.6/devicetree' of http://github.com/Broadcom/stblinux:
ARM: bcm2835: add bcm2835-aux-uart support to DT
ARM: dts: NSP: Add SP805 Support to DT
ARM: dts: NSP: Add SP804 Support to DT
ARM: dts: NSP: Add PMU Support to DT
ARM: dts: NSP: Fix CPU DT issue
ARM: dts: NSP: Fix PCIE DT issue
ARM: dts: enable GPIO-a for Broadcom NSP
ARM: bcm2835: Add the Raspberry Pi power domain driver to the DT.
ARM: bcm2835: dt: Add Raspberry Pi Model A
ARM: bcm2835: follow dt uart node-naming convention
ARM: bcm2835: Add PWM clock support to the device tree
ARM: bcm2835: add the auxiliary spi1 and spi2 to the device tree
ARM: dts: Add audio clock to the existing Broadcom Cygnus clock DT
ARM: BCM5301X: Add DT for D-Link DIR-885L
With the newly available MSIX driver for Alpine, add the corresponding
node in the Alpine device tree.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Declare the number of DMA requestor lines per platform :
- for pxa25x: 40 requestor lines
- for pxa27x: 75 requestor lines
- for pxa3xx: 100 requestor lines
This information will be used to activate the DMA flow control or not.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
- Add usb phy for Zybo
- Use earlycon instead of earlyprintk
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlbO/9UACgkQykllyylKDCFjEgCfSoTvDPwTkqsS43k3L0+gKeZi
2isAoJWtW+aNm6uWRHrB/geQ/yrAdnZJ
=UKeU
-----END PGP SIGNATURE-----
Merge tag 'zynq-dt-for-4.6' of https://github.com/Xilinx/linux-xlnx into next/dt
Merge "ARM: Xilinx Zynq dt patches for v4.6" from Michal Simek
- Add usb phy for Zybo
- Use earlycon instead of earlyprintk
* tag 'zynq-dt-for-4.6' of https://github.com/Xilinx/linux-xlnx:
ARM: zynq: Use earlycon instead of earlyprintk
ARM: dts: zynq: Enable USB and USB PHY for ZYBO
K2G SoC family is the newest version of the Keystone family of processors.
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=DF9n
-----END PGP SIGNATURE-----
Merge tag 'keystone_dts_for_4.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/dt
Merge "ARM: Keystone DTS for 4.6" from Santosh Shilimkar:
ARM: DTS: Add new bindings for K2G and the K2G evm
K2G SoC family is the newest version of the Keystone family of processors.
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
* tag 'keystone_dts_for_4.6_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: dts: keystone: Add minimum support for K2G evm
ARM: dts: keystone: Add Initial DT support for TI K2G SoC family
ARM: keystone: Create new binding for K2G SoC
adding board specific devices and few new boards:
- N900 improvments for adp1653 and gpio keys
- Add missing bandgap data for omap3
- Add more devices for compulab cm-t335
- Add n950 WLAN support, enable modem, add pinctrl for SSI
- Correct dm814x and dra62x auxclk rate, add support for GPMC and NAND
- Add syscon node for PHY's on dra7
- Add support more devices on logicpd torpedo
- Add USB host support for igep and specify boot console
- Fix audio clock for am335x-sl50 and specify boot console
- Remove deprecated tx-fifo-resize for dwc3 that was only used on
omap5 es1.0
- Add dra7 thermal data
- Update am43x-epos-evm compatible string to am438
- Add support for logicpd dm3730 som-lv
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pqea
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.6/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.6 merge window. Mostly just
adding board specific devices and few new boards:
- N900 improvments for adp1653 and gpio keys
- Add missing bandgap data for omap3
- Add more devices for compulab cm-t335
- Add n950 WLAN support, enable modem, add pinctrl for SSI
- Correct dm814x and dra62x auxclk rate, add support for GPMC and NAND
- Add syscon node for PHY's on dra7
- Add support more devices on logicpd torpedo
- Add USB host support for igep and specify boot console
- Fix audio clock for am335x-sl50 and specify boot console
- Remove deprecated tx-fifo-resize for dwc3 that was only used on
omap5 es1.0
- Add dra7 thermal data
- Update am43x-epos-evm compatible string to am438
- Add support for logicpd dm3730 som-lv
* tag 'omap-for-v4.6/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (38 commits)
ARM: dts: am57xx-beagle-x15: Add eeprom information
ARM: dts: Add HSUSB2 EHCI Support to Logic PD DM37xx SOM-LV
ARM: dts: n900: Use linux input defines instead hardcoded constants
ARM: DTS: Add minimal Support for Logic PD DM3730 SOM-LV
ARM: dts: omap3logic: Add PWM-Backlight
ARM: dts: omap3-n900: Allow gpio keys to be disabled
ARM: dts: am43x-epos-evm: Add the am438 compatible string
ARM: dts: DRA7: Add missing IVA and DSPEVE thermal domain data
ARM: dts: DRA7: Add IVA thermal data
ARM: dts: DRA7: Add DSPEVE thermal data
ARM: dts: remove deprecated property dwc3
ARM: dts: OMAP3-N950-N9: Add ssi idle pinctrl state
ARM: dts: am335x-sl50: Fix audio codec setup.
ARM: dts: am335x-sl50: Specify the device to be used for boot console output.
ARM: dts: omap3-igep0030-common: Add USB Host support
ARM: dts: igep00x0: Specify the device to be used for boot console output.
ARM: dts: LogicPD Torpedo: Set HSUSB0 Pin Mux
ARM: dts: OMAP3-N950-N9: Enable modem
ARM: dts: OMAP3-N950-N9: Enable SSI module
ARM: dts: LogicPD Torpedo: Add SPI EEPROM
...
Enable SMP support for mt7623.
Enable SMP support for mt2701
Add pinctrl for mt2701
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JHE5
-----END PGP SIGNATURE-----
Merge tag 'v4.5-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Merge "ARM: mediatek: dts updates for v4.6" from Matthias Brugger:
Add support for mt7623 SoC.
Enable SMP support for mt7623.
Enable SMP support for mt2701
Add pinctrl for mt2701
* tag 'v4.5-next-dts' of https://github.com/mbgg/linux-mediatek:
arm: dts: Add pinctrl/GPIO/EINT node for mt2701
ARM: dts: mt2701: enable basic SMP bringup for mt2701
ARM: dts: mt7623: enable SMP bringup
ARM: dts: mediatek: add MT7623 basic support
Document: DT: Add bindings for mediatek MT7623 SoC Platform
OrangePi Plus board has dwo leds - green ("pwr") and red ("status")
and a switch ("sw4"). This patch describes them in a devicetree.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds correct aliases to spi and i2c buses so that they get
correct matching bus numbers.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds i2c6 device node and pinctrls required for IFC6410 on
MIPI-CSI connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables i2c bus for camera via mipi-csi connector on ifc6410.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds gsbi4 and i2c node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds missing i2c2 pinctrl information in i2c2 node.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch enables spi device on the 30 pin expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds spi5 device node, spi5 is used on ifc6410 on the
expansion connector.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds missing i2c pinctrl sleep states.
Also add 16mA drive strength to the pins so that we can detect wide
range of i2c devices on the other side of level shifters.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds PCIE support to APQ8064, tested with Ethernet on
Compulab QS600 board.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
As there are more pinctrls to come, moving these to dedicated dtsi makes
more sense.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch fixes i2c lables to be inline with serial labels.
The reason to do this is that it would look odd if we add aliases in the
board file along with serial.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
LogicPD has two main Torpedo styles, a version with wireless and a version
without wireless. This version has Bluetooth and WiFi, but there really
isn't an easy way to identify them automatically. This simply adds
"Wireless" to the model to distinguish it from the 'base' model that will
come soon.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] dm816x TRM: SPRUGX8C: 9.2.4.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM335x TRM: SPRUH73L: 7.1.3.3.12.2 NAND Device-Ready Pin
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Cc: Teresa Remmet <t.remmet@phytec.de>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Rostislav Lisovy <lisovy@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The NAND Ready/Busy# line is connected to GPMC_WAIT0 pin and
can't be used for wait state insertion for NAND I/O read/write.
So disable read/write wait monitoring as per Reference Manual's
suggestion [1].
[1] AM437x TRM: SPRUHL7D: 9.1.3.3.12.2 NAND Device-Ready Pin
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
wait pin monitoring is not used for nand so it is pointless to
have the gpmc,wait-monitoring-ns property.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add compatible id, GPMC register resource and interrupt
resource to NAND controller nodes.
The GPMC node will provide an interrupt controller for the
NAND IRQs.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the 1588 timer node for ls1021a platform to
support gianfar ptp driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The H3 ir receiver is completely compatible with the one found in the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the corresponding device node for R_PIO on H3 to the dtsi. Support
for the controller was added in earlier commit.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
APB0 is bearly mentioned in H3 User Manual and it is only setup in the
Allwinners kernel dump for CIR. I have verified experimentally that the
gate for R_PIO exists and works, though. There are probably other gates
there but I don't know their order right now and I don't have access to
their peripherals on my board to test them.
After some experiments and reviewing how this is organized on other
sunxi SoCs, I couldn't actually find any way to disable clocks for R_PIO
and they are working properly without doing anything so I assume they
are connected straight to the 24Mhz oscillator for now.
Signed-off-by: Krzysztof Adamski <k@japko.eu>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The lamobo-r1 board, sometimes called the BPI-R1 but not labelled as such
on the PCB, is meant as a A20 based router board. As such the board comes
with a built-in switch chip giving it 5 gigabit ethernet ports, and it
has a large empty area on the pcb with mounting holes which will fit a
2.5 inch harddisk. To complete its networking features it has a
Realtek RTL8192CU for WiFi 802.11 b/g/n.
Signed-off-by: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add barebones K2G evm dts. This DTS allows the board to boot using a
ram based filesystem.
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
K2G is the newest addition of TI's Keystone 2 product family. It is a
single core Cortex A15 and a C66x DSP.
K2G supports standard peripherals such as SPI, UART, MMC and USB 2.0.
Includes two dual-core Programmable Real-time Unit and Industrial
Communication Subsystems (PRU-ICSS).
The technical reference manual for K2G can be found here:
http://www.ti.com/lit/ug/spruhy8/spruhy8.pdf
This device is targeted for a variety of applications which include, but
are not limited to:
Home audio
Professional audio
Industrial Programmable Logic Control
The peripheral nodes that have been included in this patch have been
tested during bring-up. Since all peripherals will not necessarily be
used on all boards, disable all peripherals by default. This allow
the board dts to selectively choose which peripherals it wants to
enable.
This SoC now uses the next generation of power management architecture
with the PM functionality located in a microcontroller embedded in the SOC.
Support for this new PM architecture along with other peripherals will be
added in future patches.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Use early console instead of earlyprintk which is supposed to use for
very early debugging (DEBUG_LL).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds USB HS support in host mode only.
This port supports OTG mode, but the device more is not working
properly as of now.
Once the device mode fixed, the node will be updated to support OTG.
Signed-off-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Make it possible to select which I2C IP core you want to run on the
EXIO-A connector. This is the reference how to use this feature. Update
the copyright while we are here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- Addition of the ADC for sama5d2 and sama5d2_xplained
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mzUX
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.6-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT changes for 4.6:
- Addition of the ADC for sama5d2 and sama5d2_xplained
* tag 'at91-ab-4.6-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2 Xplained: enable the adc device
ARM: dts: at91: sama5d2: add adc device
Signed-off-by: Olof Johansson <olof@lixom.net>
All Exynos SoCs have the same syscon reboot and poweroff device nodes so
there is no need to duplicate the same on each SoC dtsi and can be moved
to a common dtsi that can be included by all the SoCs dtsi files.
Suggested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung,com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
- Finalize RealView the PB1176 and PB11MPCore device trees
- Move Versatile to use the power/reset driver instead of a
custom restart hook
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NvEo
-----END PGP SIGNATURE-----
Merge tag 'versatile-dt-cleanup-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/dt
Versatile DT cleanups from Linus Walleij:
"this is a first pull request for my cleanups for the Versatile, as
the finished stuff should not be sitting in my tree but in ARM SoC.
This completes the ARM RealView PB1176 and PB11MPCore device trees,
and moves the Versatile to use power/reset.
The idea is to keep working on this cleanup branch and send additional
patches on top of this one as the prerequisites are merged into the MTD
and FBDEV subsystems. So please create a special versatile cleanup branch
(or suggest another approach).
As it happens, board files and device trees need to change at the same
time to make logical sense, especially for Versatile where auxdata is
replaced with DT entries, such as when reset is moved in the last patch
in this set. The MTD and CLCD changes will share this characteristic."
Versatile family cleanups step 1:
- Finalize RealView the PB1176 and PB11MPCore device trees
- Move Versatile to use the power/reset driver instead of a
custom restart hook
* tag 'versatile-dt-cleanup-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: versatile: move restart to the device tree
ARM: realview: add the DS1338 RTC to PB1176 DT
ARM: pb1176: add ethernet to devicetree
ARM: pb1176: add ISP1761 USB OTG host controller
ARM: pb1176: add AACI to the device tree
ARM: pb1176: add ICST307 clocks to the device tree
ARM: realview: fix up PB11MP flash compat strings
ARM: realview: add flash devices to the PB1176 DTS
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add SROM controller device nodes.
2. Add Ethernet chip as child of SROM controller on SMDK5410.
3. Allow simultaneous usage exynos-rng and s5p-sss drivers on Exynos5.
4. Cleanup CPU configuration on Exynos542x/5800.
5. Add necessary nodes for cpufreq-dt driver on Exynos542x/5800 (OPPs,
regulator supplies) which allows frequency and voltage scalling
of this SoC.
6. Minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OC9Z
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree updates and improvements for v4.6:
1. Add SROM controller device nodes.
2. Add Ethernet chip as child of SROM controller on SMDK5410.
3. Allow simultaneous usage exynos-rng and s5p-sss drivers on Exynos5.
4. Cleanup CPU configuration on Exynos542x/5800.
5. Add necessary nodes for cpufreq-dt driver on Exynos542x/5800 (OPPs,
regulator supplies) which allows frequency and voltage scalling
of this SoC.
6. Minor cleanups.
* tag 'samsung-dt-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: Replace legacy *,wakeup property with wakeup-source for exynos boards
ARM: dts: Add GSCL block parent clock management to pm domain on exynos542x
ARM: dts: Extend existing CPU OPP for exynos5800
ARM: dts: Add CPU OPP properties for exynos542x/5800
ARM: dts: Add cluster regulator supply properties for exynos542x/5800
ARM: dts: Make CPU configuration more readable on exynos542x/5800
ARM: dts: Replace legacy *,wakeup property with wakeup-source on s5pv210
ARM: dts: Allow simultaneous usage exynos-rng and s5p-sss drivers on exynos5
ARM: dts: Add Ethernet chip to exynos5410-smdk5410
ARM: dts: Add SROM to exynos5410
ARM: dts: Add SROM device node for exynos5
ARM: dts: Add SROM device node for exynos4
ARM: dts: Add pinctrl support to exynos5410
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use SCIF and USBHS fallback compatibility strings
* Add Baud Rate Generator (BRG) support for (H)SCIF
* Enable SCIF_CLK frequency and pins
* Use GIC_* defines
* Enable audio on r8a7793/gose
* Enable HDMI vidio out on r8a7793
* Enable i2c on r8a7793/gose
* Enable QSPI on alt
* Enable GPIO keys and leds on gise
* Enable audio on porter
* Enable DU on porter
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJWvirlAAoJENfPZGlqN0++H/MQAI7AQMgaAV5ejeyl7bgtsrBM
7Xq8MojRIMqCXgpEGsJ09jqnuOQIDHEaAHLNX4FWwGmJD95yCudFoeNagr79b9WF
oBHtkB9p60hw1Qz1fx9d/CjQrmAk7/TiLGBa81wNiz2D7xxmqXxYB3mdsA2oNmdV
2RPnROPM6uiZMhFM5ePiS9ku++Mv5/lvQZYnMlP8PilPpfp1VHCjcN/CXE+3AzV2
xH75tyg1A60rRmn4f2MP9kigQXC9OBdcGchI1ejwCnMGfw0THWjchAnNQ7GpV54a
N0C0pCIfGrluBXHUmvN9Fof1t5R+PNc4tyaC1SHpAEKp1uq9xKAadzonbQy9UWA2
A+iFCx0vkPo/JEbui1gE3Pixekthlk9kEXeJVBhobiraDoAIqLir5EztYLgPZUGg
wLxm1gAB6N7DrJGXxsl1ZsnkcZH4Qooy3D7kCYCqGGdse7hCIRLKdG/GXA8BK9Yz
fYPQH34kqwNpOi3Um3/VivYJjk0srTsLNMNsRTDWe7WwH7h/eK7+XuhfnJaO8di+
V0l6ptjldLwVFbpkr1RrUpIHTXoud99SfEAdu2SLADL6pumApjN2TjGTtdCzavSl
XgdshCsPiPOZ7Ou8VFDSFjfGkkEBXOAw5CJTAy+mcxn1b+vEQ5scIv0uAD1koLTS
5KyhSNdtYuBTjWk1lDlg
=YmRO
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Renesas ARM Based SoC DT Updates for v4.6
* Use SCIF and USBHS fallback compatibility strings
* Add Baud Rate Generator (BRG) support for (H)SCIF
* Enable SCIF_CLK frequency and pins
* Use GIC_* defines
* Enable audio on r8a7793/gose
* Enable HDMI vidio out on r8a7793
* Enable i2c on r8a7793/gose
* Enable QSPI on alt
* Enable GPIO keys and leds on gise
* Enable audio on porter
* Enable DU on porter
* tag 'renesas-dt-for-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (68 commits)
ARM: dts: silk: Enable SCIF_CLK frequency and pins
ARM: dts: porter: Enable SCIF_CLK frequency and pins
ARM: dts: marzen: Enable SCIF_CLK frequency and pins
ARM: dts: lager: Enable SCIF_CLK frequency and pins
ARM: dts: koelsch: Enable SCIF_CLK frequency and pins
ARM: dts: gose: Enable SCIF_CLK frequency and pins
ARM: dts: bockw: Enable SCIF_CLK frequency and pins
ARM: dts: alt: Enable SCIF_CLK frequency and pins
ARM: dts: r8a7794: Add BRG support for (H)SCIF
ARM: dts: r8a7793: Add BRG support for SCIF
ARM: dts: r8a7791: Add BRG support for (H)SCIF
ARM: dts: r8a7790: Add BRG support for (H)SCIF
ARM: dts: r8a7779: Add BRG support for SCIF
ARM: dts: r8a7778: Add BRG support for SCIF
ARM: dts: r8a7794: Rename the serial port clock to fck
ARM: dts: r8a7793: Rename the serial port clock to fck
ARM: dts: r8a7791: Rename the serial port clock to fck
ARM: dts: r8a7790: Rename the serial port clock to fck
ARM: dts: r8a7779: Rename the serial port clock to fck
ARM: dts: r8a7778: Rename the serial port clock to fck
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Initial device tree for the Artpec-6 SoC.
Signed-off-by: Lars Persson <larper@axis.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
nodes and fixes like the increased drive-strength on the firefly.
Most interesting is maybe the enablement of the pl330 option
for handling the broken flushp operation that is present on the
current Rockchip SoCs. Together with the driver-side enablement
this should give us working dma finally.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWvGKWAAoJEPOmecmc0R2B2j4IAKSBKgak7uASVfvycAnJ/E7a
jNjcz9s/SAWGAu+ES36rX23r1/u/UlkdDX0yS0vCFR4eHNn35uUrl3lQdqjFEDXZ
f/c9gCrHsfvQQJPLGRzkhFIrQ6L/Anrgk5nq75+C4GvMFRDsDo5qqRnS0iP3wIZP
VALc9PFqq9kJnnrdFymHVgc9ETCR+kTM9YGqDTzHYT2pHKxkBTAANx+Pr7/1Ib0b
BM/he5i7/K+NVb9pjw6t8JbyT2JgST+UcNFeGn6jYylYdW4awFzFvJN0Q9pp989y
7mjJe6Suh36tjp0kX0DnOvBCWYXB2i62cSsjFxsf8rZGjCbZ3YtXS15EWwXsxto=
=wj5r
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Assorted bunch of 32bit Rockchip devicetree changes. More clocks,
nodes and fixes like the increased drive-strength on the firefly.
Most interesting is maybe the enablement of the pl330 option
for handling the broken flushp operation that is present on the
current Rockchip SoCs. Together with the driver-side enablement
this should give us working dma finally.
* tag 'v4.6-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip: (30 commits)
ARM: dts: cros-ec-keyboard: Add LOCK key to keyboard matrix
ARM: dts: rockchip: replace gpio-key,wakeup with wakeup-source property
ARM: dts: rockchip: add arm,pl330-broken-no-flushp quirk for rk3036 SoCs
ARM: dts: rockchip: Add arm, pl330-broken-no-flushp quirk for rk3xxx platform
ARM: dts: rockchip: Add arm, pl330-broken-no-flushp quirk for rk3288 platform
dt-bindings: rockchip-dw-mshc: add RK3036 dw-mshc description
ARM: dts: rockchip: increase the mclk_fs to 512 for kylin board
ARM: dts: rockchip: support the spi for rk3036
ARM: dts: rockchip: add mclk for rt5616 on rk3036 kylin board
ARM: dts: rockchip: add the leds control for rk3036-kylin board
ARM: dts: rockchip: add tsadc node
clk: rockchip: Add new id for rk3066 tsadc clock
ARM: dts: rockchip: add clock-cells for usb phy nodes
ARM: dts: rockchip: Assign RK3288 EDP_24M input centrally
ARM: dts: rockchip: add soc-specific compatibles for rk3036 SoCs
ARM: dts: rockchip: Bump sd card pin drive strength up on firefly boards
dt-bindings: rockchip-dw-mshc: add RK3368 dw-mshc description
ARM: dts: rockchip: Add the SDIO wifi on Radxa Rock2 square
ARM: dts: rockchip: Add the iodomains for the Rock2 SOM
ARM: dts: rockchip: add rk3288 mipi_dsi nodes
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge DT changes for lpc32xx from Vladimir Zapolskiy:
"The changes add description of clock providers and clock consumers,
define default irq types of SoC controllers and add PHY3250 board
regulators.
I'm adding an official LPC32xx maintainer Roland to Cc, however he seems
to be unresponsive for a quite long time (since 2014)."
* 'lpc32xx/dt' of https://github.com/vzapolskiy/linux:
arm: dts: phy3250: add SD fixed regulator
arm: dts: phy3250: add lcd and backlight fixed regulators
arm: dts: lpc32xx: assign interrupt types
arm: dts: lpc32xx: remove clock frequency property from UART device nodes
arm: dts: lpc32xx: add USB clock controller
arm: dts: lpc32xx: add clock properties to device nodes
arm: dts: lpc32xx: add clock controller device node
arm: dts: lpc32xx: add device nodes for external oscillators
dt-bindings: create arm/nxp folder and move LPC32xx SoC description to it
Signed-off-by: Olof Johansson <olof@lixom.net>
Cyrille Pitchen