Since lots of MediaTek drivers had been added, it seems slightly better
for that adding cleanup for placing MediaTek pinctrl drivers under the
independent menu as other kinds of drivers usually was done.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver consists of 2 controllers due to a hole in mapping:
-1 controller for GPIO bankA to K.
-1 controller for GPIO bankZ.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In case a platform only defaults a "default" set of pins, but not a
"sleep" set of pins, and this particular platform suspends and resumes
in a way that the pin states are not preserved by the hardware, when we
resume, we would call pinctrl_single_resume() -> pinctrl_force_default()
-> pinctrl_select_state() and the first thing we do is check that the
pins state is the same as before, and do nothing.
In order to fix this, decouple the actual state change from
pinctrl_select_state() and move it pinctrl_commit_state(), while keeping
the p->state == state check in pinctrl_select_state() not to change the
caller assumptions. pinctrl_force_sleep() and pinctrl_force_default()
are updated to bypass the state check by calling pinctrl_commit_state().
[Linus Walleij]
The forced pin control states are currently only used in some pin
controller drivers that grab their own reference to their own pins.
This is equal to the pin control hogs: pins taken by pin control
devices since there are no corresponding device in the Linux device
hierarchy, such as memory controller lines or unused GPIO lines,
or GPIO lines that are used orthogonally from the GPIO subsystem
but pincontrol-wise managed as hogs (non-strict mode, allowing
simultaneous use by GPIO and pin control). For this case forcing
the state from the drivers' suspend()/resume() callbacks makes
sense and should semantically match the name of the function.
Fixes: 6e5e959dde ("pinctrl: API changes to support multiple states per device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds tpu groups and function to r8a7743/r8a7791/r8a7793.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add i2c5 pin groups and function to r8a7745 PFC driver.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds tpu groups and function to r8a7745/r8a7794.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds PFC PWM[0123456] pin groups and functions, enabling
PWM on the r8a7794 and r8a7745.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
According to datasheet, we should use numbers for the pin naming
instead of letters. The patch here try to fix this to keep
the consistency.
This patch should not bring any functional change.
Fixes: 83c566806a ("pinctrl: meson-axg: Add new pinctrl driver for Meson AXG SoC")
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Guenter Roeck reported an interrupt storm on a prototype system which is
based on Cyan Chromebook. The root cause turned out to be a incorrectly
configured pin that triggers spurious interrupts. This will be fixed in
coreboot but currently we need to prevent the interrupt storm from
happening by masking all interrupts (but not GPEs) on those systems.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197953
Fixes: bcb48cca23 ("pinctrl: cherryview: Do not mask all interrupts in probe")
Reported-and-tested-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AXP813 has only two GPIOs. GPIO0 can either be used as a GPIO, an
LDO regulator or an ADC. GPIO1 can be used either as a GPIO or an LDO
regulator.
Moreover, the status bit of the GPIOs when in input mode is not offset
by 4 unlike the AXP209.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prepare for patches that will add support for a new PMIC that has a
different GPIO adc muxing value, add an adc_mux within axp20x_pctl
structure and use it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prepare for patches that will add support for a new PMIC that has a
different GPIO input status register, add a gpio_status_offset within
axp20x_pctl structure and use it.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver used to do only GPIO features of the GPIOs in X-Powers
AXP20X. Now that we have migrated everything to the pinctrl subsystem
and added pinctrl features, rename everything related to pinctrl from
gpio to pctl to ease the understanding of differences between GPIO
and pinctrl features.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The X-Powers AXP209 has 3 GPIOs. GPIO0/1 can each act either as a GPIO,
an ADC or a LDO regulator. GPIO2 can only act as a GPIO.
This adds the pinctrl features to the driver so GPIO0/1 can be used as
ADC or LDO regulator.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To prepare the driver for the upcoming pinctrl features, move the GPIO
driver AXP209 from GPIO to pinctrl subsystem.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the (unlikely) event that community->ngpps is zero, or if every
gpp->gpio_base is less than zero, then an ininitialized value in
ret is returned by function intel_gpio_add_pin_ranges. Fix this by
ensuring ret is initialized to zero. It's a moot point, but I think
it is worthwhile ensuring this corner case is fixed.
Detected by CoverityScan, CID#1462415 ("Uninitialized scalar variable")
Fixes: a60eac3239 ("pinctrl: intel: Allow custom GPIO base for pad groups")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Gemini pin controller can set drive strength for a few
select groups of pins (not individually). Implement this
for GMAC0 and 1 (ethernet ports), IDE and PCI.
Cc: devicetree@vger.kernel.org
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds CAN FD[0-1] pinmux support to the r8a77995 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN[0-1] pinmux support to the r8a77995 SoC.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch renames the pin function macro definitions of the GPSR5 and
IPSR{0,3,5,6,12} registers value for the RTS{0,1,3,4}# pin.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch renames the pin function macro definitions of the GPSR and
IPSR registers value for the RTS{0,1,3,4}# pin.
This is a correction because GPSR and IPSR register specification for
R8A7795 ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual
Rev.0.54E.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Drop remaining "_TANS" from comments]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of A20..A25 pins function deleted.
This is a correction because IPSR register specification for R8A7796 SoC
was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of A20..A25 pins function deleted.
This is a correction because IPSR register specification for R8A7795 ES2.0
SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL1 bit[25:24]
value when STP_ISEN_1_D pin function is selected for IPSR16 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7795 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E.
Fixes: 0b0ffc96db ("pinctrl: sh-pfc: Initial R8A7795 PFC support)
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch supports GP-1-28 port pin of R8A7795 ES2.0 SoC added in
Rev.0.54E of the R-Car Gen3 Hardware User's Manual or later version.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
[geert: Update forgotten PUEN2 entry]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds can_clk function to r8a7743/r8a7791 which is cleaner,
and allows for independent configuration.
We keep the can_clk* pins definitions from within can0_groups and
can1_groups for uniformity and backwards compatibility.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds can_clk function to r8a7745/r8a7794 which is cleaner,
and allows for independent configuration.
We keep the can_clk* pins definitions from within can0_groups and
can1_groups for uniformity and backwards compatibility.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add the PFC support for the R8A77970 SoC including pin groups for some
on-chip devices such as CAN-FD, [H]SCIF, I2C, INTC-EX, MMC, MSIOF, PWM,
VIN...
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
[geert: Drop EtherAVB for now]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When a GPIO is requested using gpiod_get_* APIs the intel pinctrl driver
switches the pin to GPIO mode and makes sure interrupts are routed to
the GPIO hardware instead of IOAPIC. However, if the GPIO is used
directly through irqchip, as is the case with many I2C-HID devices where
I2C core automatically configures interrupt for the device, the pin is
not initialized as GPIO. Instead we rely that the BIOS configures the
pin accordingly which seems not to be the case at least in Asus X540NA
SKU3 with Focaltech touchpad.
When the pin is not properly configured it might result weird behaviour
like interrupts suddenly stop firing completely and the touchpad stops
responding to user input.
Fix this by properly initializing the pin to GPIO mode also when it is
used directly through irqchip.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Reported-by: Daniel Drake <drake@endlessm.com>
Reported-and-tested-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All of the H5 boards in the kernel reference the MMC0 CD pin twice in
their DT, so strict mode will make the MMC driver fail to load.
To keep existing DTs working, disable strict mode in the H5 driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Chris Obbard <obbardc@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To use pin PF4 as the RX signal of UART0, we have to write 0b011 into
the respective pin controller register.
Fix the wrong value we had in our table so far.
Fixes: 96851d391d ("drivers: pinctrl: add driver for Allwinner A64 SoC")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the A80 the pins on port B can trigger interrupts, and those are
assigned to the second interrupt bank.
Having two pins assigned to the same interrupt bank/pin combination does
not look healthy (instead more like a copy&paste bug from pins PA14-PA16),
so fix the interrupt bank for pins PB14-PB16, which is actually 1.
I don't have any A80 board, so could not test this.
Fixes: d5e9fb31ba ("pinctrl: sunxi: Add A80 pinctrl muxing options")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin config lookup function was still hardcoding the
3516 pin set, which is obviously wrong. Use the pointer
in the state container.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change resolves a new compile-time warning
when built as a loadable module:
WARNING: modpost: missing MODULE_LICENSE() in drivers/pinctrl/pxa/pinctrl-pxa2xx.o
see include/linux/module.h for more information
This adds the license as "GPL v2", which matches the header of the file.
MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: Jesse Chan <jc@linux.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 3512 has two more GPIO groups on GPIO area 0, so let's
make it possible to combine these with the function.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller has been updated in the Amlogic Meson AXG series,
which use continuous 4-bit register to select function for each pin.
In order to support this, a new pinmux operations "meson_axg_pmx_ops"
has been added.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The direction_output callback of the gpio_chip structure is supposed to
set the output direction but also to set the value of the gpio. For the
armada-37xx driver this callback acted as the gpio_set_direction callback
for the pinctrl.
This patch fixes the behavior of the direction_output callback by also
applying the value received as parameter.
Cc: stable@vger.kernel.org
Fixes: 5715092a45 ("pinctrl: armada-37xx: Add gpio support")
Reported-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Add a jump target so that a call of the function "mutex_unlock" is stored
only twice in this function implementation.
* Replace five calls by goto statements.
* Adjust five condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Cannon Lake Windows GPIO driver always exposes 32 pins per "bank"
regardless of whether the hardware actually has that many pins in a pad
group. This means that there are gaps in the GPIO number space even if
such gaps do not exist in the real hardware. To make things worse the
BIOS is also using the same scheme, so for example on Cannon Lake-LP
vGPIO 39 (vSD3_CD_B) the ACPI GpioInt resource has number 231 instead of
the expected 180 (which would be the hardware number).
To make SD card detection and other GPIOs working properly in Linux we
align the pinctrl-cannonlake GPIO numbering to follow the Windows GPIO
driver numbering taking advantage of the gpio_base field introduced in
the previous patch.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we always have direct mapping between GPIO numbers and the
hardware pin numbers. However, there are cases where that's not the case
anymore (more about this in the next patch). Instead we need to be able
to specify custom GPIO base for certain pad groups.
To support this, add a new field (gpio_base) to the pad group structure
and update the core Intel pinctrl driver to handle this accordingly.
Passing 0 as gpio_base will use direct mapping so the existing drivers
do not need to be modified. Passing -1 excludes the whole pad group from
having GPIO mapping.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We added acpi_gpiochip_pin_to_gpio_offset() because there was a need to
translate from ACPI GpioIo/GpioInt number to Linux GPIO number in the
Cherryview pinctrl driver. This translation is necessary because
Cherryview has gaps in the pin list and the driver used continuous GPIO
number space in Linux side as follows:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 8->19 ==> INT33FF:03 PIN 15->26
created GPIO range 20->25 ==> INT33FF:03 PIN 30->35
created GPIO range 26->33 ==> INT33FF:03 PIN 45->52
created GPIO range 34->43 ==> INT33FF:03 PIN 60->69
created GPIO range 44->54 ==> INT33FF:03 PIN 75->85
For example when ACPI GpioInt resource refers to GPIO 81 (SDMMC3_CD_B)
we translate from pin 81 to the corresponding Linux GPIO number, which
is 50. This number is then used when the GPIO is accessed through gpiolib.
It turns out, this is not necessary at all. We can just pass 1:1 mapping
between Linux GPIO numbers and pin numbers (including gaps) and the
pinctrl core handles all the details automatically:
created GPIO range 0->7 ==> INT33FF:03 PIN 0->7
created GPIO range 15->26 ==> INT33FF:03 PIN 15->26
created GPIO range 30->35 ==> INT33FF:03 PIN 30->35
created GPIO range 45->52 ==> INT33FF:03 PIN 45->52
created GPIO range 60->69 ==> INT33FF:03 PIN 60->69
created GPIO range 75->85 ==> INT33FF:03 PIN 75->85
Here GPIO 81 is exactly same than the hardware pin 81 (SDMMC3_CD_B).
As an added bonus this simplifies both the ACPI GPIO core code and the
Cherryview pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Intel Merrifield the pin control device is a separate IP block
without any PCI ID assigned.
Though, recently we got an allocated ACPI ID for it, so, let's use fresh
ID.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
UART2 RTS is mode 2 of the pin.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
They follow the style of the existing PORT_GP_CFG_<n>() macros and
will be used by a follow-up patch for the R8A77970 SoC.
Based on the original (and large) patch by Daisuke Matsushita
<daisuke.matsushita.ns@hitachi.com>.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN FD[0-1] pinmux support for R-Car H3 ES2.0. The pin
config is identical to H3 ES1.*.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds CAN[0-1] pinmux support for R-Car H3 ES2.0. The pin
config is identical to H3 ES1.*.
Signed-off-by: Ramesh Shanmugasundaram <ramesh.shanmugasundaram@bp.renesas.com>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds PFC CAN0 and CAN1 pin groups and functions, enabling CAN
bus on the RZ/G1E.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into
a menuconfig option. This obviously has the implication of
making the subsystem menu visible in menuconfig. This is
happening because of two things:
- Intel have started to deploy and depend on pin controllers
in a way that is affecting users directly. This happens
on the highly integrated laptop chipsets named after
geographical places: baytrail, broxton, cannonlake,
cedarfork, cherryview, denverton, geminilake, lewisburg,
merrifield, sunrisepoint... It started a while back and
now it is ever more evident that this is crucial
infrastructure for x86 laptops and not an embedded
obscurity anymore. Users need to be aware.
- Pin control expanders on I2C and SPI that are
arch-agnostic. Currently Semtech SX150X and Microchip
MCP28x08 but more are expected. Users will have to be
able to configure these in directly for their set-up.
- Just go and select GPIOLIB now that we made sure that
GPIOLIB is a very vanilla subsystem. Do not depend on
it, if we need it, select it.
- Exposing the pin control subsystem in menuconfig uncovered
a bunch of obscure bugs that are now hopefully fixed,
all more or less pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and
GPIO.
- New support for clock skew/delay generic DT bindings
and generic pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying.
-----BEGIN PGP SIGNATURE-----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=kj/b
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.15 kernel cycle:
Core:
- The pin control Kconfig entry PINCTRL is now turned into a
menuconfig option. This obviously has the implication of making the
subsystem menu visible in menuconfig. This is happening because of
two things:
(a) Intel have started to deploy and depend on pin controllers in
a way that is affecting users directly. This happens on the
highly integrated laptop chipsets named after geographical
places: baytrail, broxton, cannonlake, cedarfork, cherryview,
denverton, geminilake, lewisburg, merrifield, sunrisepoint...
It started a while back and now it is ever more evident that
this is crucial infrastructure for x86 laptops and not an
embedded obscurity anymore. Users need to be aware.
(b) Pin control expanders on I2C and SPI that are arch-agnostic.
Currently Semtech SX150X and Microchip MCP28x08 but more are
expected. Users will have to be able to configure these in
directly for their set-up.
- Just go and select GPIOLIB now that we made sure that GPIOLIB is a
very vanilla subsystem. Do not depend on it, if we need it, select
it.
- Exposing the pin control subsystem in menuconfig uncovered a bunch
of obscure bugs that are now hopefully fixed, all more or less
pertaining to Blackfin.
- Unified namespace for cross-calls between pin control and GPIO.
- New support for clock skew/delay generic DT bindings and generic
pin config options for this.
- Minor documentation improvements.
Various:
- The Renesas SH-PFC pin controller has evolved a lot. It seems
Renesas are churning out new SoCs by the minute.
- A bunch of non-critical fixes for the Rockchip driver.
- Improve the use of library functions instead of open coding.
- Support the MCP28018 variant in the MCP28x08 driver.
- Static constifying"
* tag 'pinctrl-v4.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (91 commits)
pinctrl: gemini: Fix missing pad descriptions
pinctrl: Add some depends on HAS_IOMEM
pinctrl: samsung/s3c24xx: add CONFIG_OF dependency
pinctrl: gemini: Fix GMAC groups
pinctrl: qcom: spmi-gpio: Add pmi8994 gpio support
pinctrl: ti-iodelay: remove redundant unused variable dev
pinctrl: max77620: Use common error handling code in max77620_pinconf_set()
pinctrl: gemini: Implement clock skew/delay config
pinctrl: gemini: Use generic DT parser
pinctrl: Add skew-delay pin config and bindings
pinctrl: armada-37xx: Add edge both type gpio irq support
pinctrl: uniphier: remove eMMC hardware reset pin-mux
pinctrl: rockchip: Add iomux-route switching support for rk3288
pinctrl: intel: Add Intel Cedar Fork PCH pin controller support
pinctrl: intel: Make offset to interrupt status register configurable
pinctrl: sunxi: Enforce the strict mode by default
pinctrl: sunxi: Disable strict mode for old pinctrl drivers
pinctrl: sunxi: Introduce the strict flag
pinctrl: sh-pfc: Save/restore registers for PSCI system suspend
pinctrl: sh-pfc: r8a7796: Use generic IOCTRL register description
...
CORE:
- Fix the semantics of raw GPIO to actually be raw. No
inversion semantics as before, but also no open draining,
and allow the raw operations to affect lines used for
interrupts as the caller supposedly knows what they are
doing if they are getting the big hammer.
- Rewrote the __inner_function() notation calls to names that
make more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all
IRQs are mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This
allows us to read several GPIO lines with a single
register read. This has high value for some usecases: it
can be used to create oscilloscopes and signal analyzers
and other things that rely on reading several lines at
exactly the same instant. Also a generally nice
optimization. This uses the new assign_bit() macro from
the bitops lib that was ACKed by Andrew Morton and
is implemented for two drivers, one of them being the
generic MMIO driver so everyone using that will be able
to benefit from this.
- Do not allow requests of Open Drain and Open Source
setting of a GPIO line simultaneously. If the hardware
actually supports enabling both at the same time the
electrical result would be disastrous.
- A new interrupt chip core helper. This will be helpful
to deal with "banked" GPIOs, which means GPIO controllers
with several logical blocks of GPIO inside them. This
is several gpiochips per device in the device model, in
contrast to the case when there is a 1-to-1 relationship
between a device and a gpiochip.
NEW DRIVERS:
- Maxim MAX3191x industrial serializer, a very interesting
piece of professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the
recent Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
OTHER IMPROVEMENTS:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the
Broadcom BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal
of dead code etc.
- Explicit comments on fall-through switch() statements.
-----BEGIN PGP SIGNATURE-----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=8Mon
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.15 kernel cycle:
Core:
- Fix the semantics of raw GPIO to actually be raw. No inversion
semantics as before, but also no open draining, and allow the raw
operations to affect lines used for interrupts as the caller
supposedly knows what they are doing if they are getting the big
hammer.
- Rewrote the __inner_function() notation calls to names that make
more sense. I just find this kind of code disturbing.
- Drop the .irq_base() field from the gpiochip since now all IRQs are
mapped dynamically. This is nice.
- Support for .get_multiple() in the core driver API. This allows us
to read several GPIO lines with a single register read. This has
high value for some usecases: it can be used to create
oscilloscopes and signal analyzers and other things that rely on
reading several lines at exactly the same instant. Also a generally
nice optimization. This uses the new assign_bit() macro from the
bitops lib that was ACKed by Andrew Morton and is implemented for
two drivers, one of them being the generic MMIO driver so everyone
using that will be able to benefit from this.
- Do not allow requests of Open Drain and Open Source setting of a
GPIO line simultaneously. If the hardware actually supports
enabling both at the same time the electrical result would be
disastrous.
- A new interrupt chip core helper. This will be helpful to deal with
"banked" GPIOs, which means GPIO controllers with several logical
blocks of GPIO inside them. This is several gpiochips per device in
the device model, in contrast to the case when there is a 1-to-1
relationship between a device and a gpiochip.
New drivers:
- Maxim MAX3191x industrial serializer, a very interesting piece of
professional I/O hardware.
- Uniphier GPIO driver. This is the GPIO block from the recent
Socionext (ex Fujitsu and Panasonic) platform.
- Tegra 186 driver. This is based on the new banked GPIO
infrastructure.
Other improvements:
- Some documentation improvements.
- Wakeup support for the DesignWare DWAPB GPIO controller.
- Reset line support on the DesignWare DWAPB GPIO controller.
- Several non-critical bug fixes and improvements for the Broadcom
BRCMSTB driver.
- Misc non-critical bug fixes like exotic errorpaths, removal of dead
code etc.
- Explicit comments on fall-through switch() statements"
* tag 'gpio-v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (65 commits)
gpio: tegra186: Remove tegra186_gpio_lock_class
gpio: rcar: Add r8a77995 (R-Car D3) support
pinctrl: bcm2835: Fix some merge fallout
gpio: Fix undefined lock_dep_class
gpio: Automatically add lockdep keys
gpio: Introduce struct gpio_irq_chip.first
gpio: Disambiguate struct gpio_irq_chip.nested
gpio: Add Tegra186 support
gpio: Export gpiochip_irq_{map,unmap}()
gpio: Implement tighter IRQ chip integration
gpio: Move lock_key into struct gpio_irq_chip
gpio: Move irq_valid_mask into struct gpio_irq_chip
gpio: Move irq_nested into struct gpio_irq_chip
gpio: Move irq_chained_parent to struct gpio_irq_chip
gpio: Move irq_default_type to struct gpio_irq_chip
gpio: Move irq_handler to struct gpio_irq_chip
gpio: Move irqdomain into struct gpio_irq_chip
gpio: Move irqchip into struct gpio_irq_chip
gpio: Introduce struct gpio_irq_chip
pinctrl: armada-37xx: remove unused variable
...
Pull irq core updates from Thomas Gleixner:
"A rather large update for the interrupt core code and the irq chip drivers:
- Add a new bitmap matrix allocator and supporting changes, which is
used to replace the x86 vector allocator which comes with separate
pull request. This allows to replace the convoluted nested loop
allocation function in x86 with a facility which supports the
recently added property of managed interrupts proper and allows to
switch to a best effort vector reservation scheme, which addresses
problems with vector exhaustion.
- A large update to the ARM GIC-V3-ITS driver adding support for
range selectors.
- New interrupt controllers:
- Meson and Meson8 GPIO
- BCM7271 L2
- Socionext EXIU
If you expected that this will stop at some point, I have to
disappoint you. There are new ones posted already. Sigh!
- STM32 interrupt controller support for new platforms.
- A pile of fixes, cleanups and updates to the MIPS GIC driver
- The usual small fixes, cleanups and updates all over the place.
Most visible one is to move the irq chip drivers Kconfig switches
into a separate Kconfig menu"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
genirq: Fix type of shifting literal 1 in __setup_irq()
irqdomain: Drop pointless NULL check in virq_debug_show_one
genirq/proc: Return proper error code when irq_set_affinity() fails
irq/work: Use llist_for_each_entry_safe
irqchip: mips-gic: Print warning if inherited GIC base is used
irqchip/mips-gic: Add pr_fmt and reword pr_* messages
irqchip/stm32: Move the wakeup on interrupt mask
irqchip/stm32: Fix initial values
irqchip/stm32: Add stm32h7 support
dt-bindings/interrupt-controllers: Add compatible string for stm32h7
irqchip/stm32: Add multi-bank management
irqchip/stm32: Select GENERIC_IRQ_CHIP
irqchip/exiu: Add support for Socionext Synquacer EXIU controller
dt-bindings: Add description of Socionext EXIU interrupt controller
irqchip/gic-v3-its: Fix VPE activate callback return value
irqchip: mips-gic: Make IPI bitmaps static
irqchip: mips-gic: Share register writes in gic_set_type()
irqchip: mips-gic: Remove gic_vpes variable
irqchip: mips-gic: Use num_possible_cpus() to reserve IPIs
irqchip: mips-gic: Configure EIC when CPUs come online
...
A pretty clever static checker found a bug in my patch: I added more
bits to a bitmask but didn't extend the array indexed to the same
bitmask.
Fixes: 756a024f39 ("pinctrl: gemini: Fix GMAC groups")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some compilation fallout from UM Linux (which does not have
IOMEM) makes it necessary to depend on HAS_IOMEM for drivers
that doesn't have other factors restricting their selection.
Cc: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reported-by: R. Daneel Olivaw <kbuild-all@01.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver fails to build without CONFIG_OF:
drivers/pinctrl/samsung/pinctrl-samsung.c: In function 'samsung_gpiolib_register':
drivers/pinctrl/samsung/pinctrl-samsung.c:936:5: error: 'struct gpio_chip' has no member named 'of_node'
This configuration is now possible since we can now select the
PINCTRL subsystem on S3C24xx machines other than the device tree
based ones.
Fixes: d219b92461 ("pinctrl: change Kconfig PINCTRL variable to a menuconfig")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixing a small merge problem in BCM2835 related to the
new irqchip code.
Cc: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to consolidate the multiple ways to associate an IRQ chip with
a GPIO chip, move more fields into the new struct gpio_irq_chip.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GMII groups need to be split across GMAC0 and GMAC1 since
GMAC0 is always available but GMAC1 masks GPIO2 lines 0-7
so we might want just one interface out.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update the binding and driver for pmi8994-gpios
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pointer dev is being assigned but is never used, hence it is
redundant and can be removed. Cleans up clang warnings:
drivers/pinctrl/ti/pinctrl-ti-iodelay.c:582:2: warning: Value stored
to 'dev' is never read
drivers/pinctrl/ti/pinctrl-ti-iodelay.c:701:2: warning: Value stored
to 'dev' is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Add a jump target so that a specific error message is stored only once
at the end of this function implementation.
* Replace two calls of the function "dev_err" by goto statements.
* Adjust two condition checks.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enabled pin config on the Gemini driver and implements
pin skew/delay so that the ethernet pins clocking can be
properly configured.
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We can just use the generic Device Tree parser code
in this driver and save some code.
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pin controllers (such as the Gemini) can control the
expected clock skew and output delay on certain pins with a
sub-nanosecond granularity. This is typically done by shunting
in a number of double inverters in front of or behind the pin.
Make it possible to configure this with a generic binding.
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A cleanup left behind a temporary variable that is now unused:
drivers/pinctrl/mvebu/pinctrl-armada-37xx.c: In function 'armada_37xx_irq_startup':
drivers/pinctrl/mvebu/pinctrl-armada-37xx.c:693:20: error: unused variable 'chip' [-Werror=unused-variable]
This removes the declarations as well.
Fixes: 3ee9e605ca ("pinctrl: armada-37xx: Stop using struct gpio_chip.irq_base")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWfswbQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykvEwCfXU1MuYFQGgMdDmAZXEc+xFXZvqgAoKEcHDNA
6dVh26uchcEQLN/XqUDt
=x306
-----END PGP SIGNATURE-----
Merge tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull initial SPDX identifiers from Greg KH:
"License cleanup: add SPDX license identifiers to some files
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the
'GPL-2.0' SPDX license identifier. The SPDX identifier is a legally
binding shorthand, which can be used instead of the full boiler plate
text.
This patch is based on work done by Thomas Gleixner and Kate Stewart
and Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset
of the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to
license had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied
to a file was done in a spreadsheet of side by side results from of
the output of two independent scanners (ScanCode & Windriver)
producing SPDX tag:value files created by Philippe Ombredanne.
Philippe prepared the base worksheet, and did an initial spot review
of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537
files assessed. Kate Stewart did a file by file comparison of the
scanner results in the spreadsheet to determine which SPDX license
identifier(s) to be applied to the file. She confirmed any
determination that was not immediately clear with lawyers working with
the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained
>5 lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that
was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that
became the concluded license(s).
- when there was disagreement between the two scanners (one detected
a license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply
(and which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases,
confirmation by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights.
The Windriver scanner is based on an older version of FOSSology in
part, so they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot
checks in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect
the correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial
patch version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch
license was not GPL-2.0 WITH Linux-syscall-note to ensure that the
applied SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'spdx_identifiers-4.14-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
License cleanup: add SPDX license identifier to uapi header files with a license
License cleanup: add SPDX license identifier to uapi header files with no license
License cleanup: add SPDX GPL-2.0 license identifier to files with no license
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current edge both type gpio irqs which need to swap polarity in each
interrupt are not supported, this patch adds edge both type gpio irq
support.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is handled by the mmc-pwrseq-emmc driver, which controls
an eMMC hardware reset via a GPIO line.
Remove it from the function pin-mux settings.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rk3288 also has one function that can be routed to one of two pins,
the hdmi cec functionality can use either gpio7c0 or gpio7c7.
So add the route switching support for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Cedar Fork PCH is the successor of Intel Denverton PCH but it is
based on the newer GPIO/pinctrl hardware block. Add a new pinctrl/GPIO
driver to support it.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some GPIO blocks have the interrupt status (GPI_IS) offset different
than it normally is, so make it configurable. If no offset is specified
we use the default.
While there remove two unused constants from the core driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The strict mode should always have been enabled on our driver, and leaving
it unchecked just makes it harder to find a migration path as time passes.
Let's enable it by default now so that hopefully the new SoCs should be
safe.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Old pinctrl drivers will need to disable strict mode for various reasons,
among which:
- Some DT will still have a pinctrl group for each GPIO used, which will
be rejected by pin_request. While we could remove those nodes, we still
have to deal with old DTs.
- Some GPIOs on these boards need to have their pin configuration changed
(for bias or current), and there's no clear migration path
Let's disable the strict mode on those SoCs so that there's no breakage.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Our pinctrl device should have had strict set all along. However, it wasn't
the case, and most of our old device trees also have a pinctrl group in
addition to the GPIOs properties, which mean that we can't really turn it
on now.
All our new SoCs don't have that group, so we should still enable that mode
on the newer one though.
In order to enable it by default, add a flag that will allow to disable
that mode that should be set by pinctrl drivers that cannot be migrated.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add Audio, HSCIF, I2C, and INTC-EX pin groups on R-Car H3 ES2.0,
- Add Audio and PWM pin groups on R-Car D3,
- Add support for RZ/A1M and RZ/A1L,
- Add INTC-EX pin groups on R-Car M3-W,
- Add SDHI voltage switching on RZ/G1E,
- Make bias control and IOCTRL support more generic,
- Add suspend/resume support for R-Car Gen3,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6Arb
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.15-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.15 (take two)
- Add Audio, HSCIF, I2C, and INTC-EX pin groups on R-Car H3 ES2.0,
- Add Audio and PWM pin groups on R-Car D3,
- Add support for RZ/A1M and RZ/A1L,
- Add INTC-EX pin groups on R-Car M3-W,
- Add SDHI voltage switching on RZ/G1E,
- Make bias control and IOCTRL support more generic,
- Add suspend/resume support for R-Car Gen3,
- Small fixes and cleanups.
During PSCI system suspend, R-Car Gen3 SoCs are powered down, and their
pinctrl register state is lost. Note that as the boot loader skips most
initialization after system resume, pinctrl register state differs from
the state encountered during normal system boot, too.
To fix this, save all GPIO and peripheral function select, module
select, drive strength control, bias, and other I/O control registers
during system suspend, and restore them during system resume.
Note that to avoid overhead on platforms not needing it, the
suspend/resume code has a build time dependency on sleep and PSCI
support, and a runtime dependency on PSCI.
Inspired by a patch in the BSP by Hien Dang.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move R-Car M3-W I/O voltage support over to the generic way to describe
IOCTRL registers, which will be needed for suspend/resume support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move R-Car H3 ES2.0 I/O voltage support over to the generic way to
describe IOCTRL registers, which will be needed for suspend/resume
support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move R-Car H3 ES1.x I/O voltage support over to the generic way to
describe IOCTRL registers, which will be needed for suspend/resume
support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a generic way to describe IOCTRL registers (for e.g. SD I/O voltage
and time delay control), like is already done for config, drive, and
bias registers.
This makes the sh-pfc core code aware of these registers, which will
ease introducing suspend/resume support later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
All users of sh_pfc_pin_to_bias_info() and the related data structures
have been converted to sh_pfc_pin_to_bias_reg(), so those can be
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Move R-Car M1A bias support over to the generic way to describe bias
registers.
As the new description is more compact, this decreases kernel size by
ca. 148 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move R-Car M3-W bias support over to the generic way to describe bias
registers, which will be needed for suspend/resume support.
As the new description is more compact, this decreases kernel size by
ca. 304 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move R-Car H3 ES2.0 bias support over to the generic way to describe
bias registers, which will be needed for suspend/resume support.
As the new description is more compact, this decreases kernel size by
ca. 308 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Move R-Car H3 ES1.x bias support over to the generic way to describe
bias registers, which will be needed for suspend/resume support.
As the new description is more compact, this decreases kernel size by
ca. 304 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Add a helper to look up bias registers and bit number for a specific
pin, using the generic bias register description.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add a generic way to describe bias registers (for pull-up/down control),
like is already done for config and drive registers.
This makes the sh-pfc core code aware of these registers, which will
ease introducing suspend/resume support later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
On modern Renesas SoCs, all PFC registers are 32-bit, and all callers of
sh_pfc_{read,write}_reg() already operate on 32-bit registers only.
Hence make the 32-bit width implicit, and rename the functions to
sh_pfc_{read,write}() to shorten lines.
All accesses to 8-bit or 16-bit registers are still done using
sh_pfc_{read,write}_raw_reg().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
As of commit 8682b3c522 ("sh-pfc: Remove platform device
registration"), plain "sh-pfc" platform devices are no longer created.
Hence remove their match entry, and the now obsolete checks for missing
device IDs and driver data.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
The Armada 37xx driver always initializes the IRQ base to 0, hence the
subtraction is a no-op. Remove the subtraction and thereby the last user
of struct gpio_chip's .irq_base field.
Note that this was also actually a bug and only worked because of the
above assumption. If the IRQ base had been dynamically allocated, the
subtraction would've caused the wrong mask to be generated since the
struct irq_data.hwirq field is an index local to the IRQ domain. As a
result, it should now be safe to also allocate this chip's IRQ base
dynamically, unless there are consumers left that refer to the IRQs by
their global number.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds the required definitions for the mcp23018 which is the i2c
variant of the mcp23s18.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
interrupt handling was broken with conversion to using regmap caching.
cached_gpio value was updated by boolean status instead of gpio reading.
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Dmitry Mastykin <mastichi@gmail.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On Asus laptop models X505BA, X505BP, X542BA and X542BP, the i2c-hid
touchpad (using a GPIO for interrupts) becomes unresponsive after a
few minutes of usage, or after placing two fingers on the touchpad,
which seems to have the effect of queuing up a large amount of input
data to be transferred.
When the touchpad is in unresponsive state, we observed that the GPIO
level-triggered interrupt is still at it's active level, however the
pinctrl-amd driver is not receiving/dispatching more interrupts at this
point.
After the initial interrupt arrives, amd_gpio_irq_mask() is called
however we then see amd_gpio_irq_handler() being called repeatedly for
the same irq; the interrupt mask is not taking effect because of the
following sequence of events:
- amd_gpio_irq_handler fires, reads and caches pin reg
- amd_gpio_irq_handler calls generic_handle_irq()
- During IRQ handling, amd_gpio_irq_mask() is called and modifies pin reg
- amd_gpio_irq_handler clears interrupt by writing cached value
The stale cached value written at the final stage undoes the masking.
Fix this by re-reading the register before clearing the interrupt.
I also spotted that the interrupt-clearing code can race against
amd_gpio_irq_mask() / amd_gpio_irq_unmask(), so add locking there.
Presumably this race was leading to the loss of interrupts.
After these changes, the touchpad appears to be working fine.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Acked-by: Shah, Nehal-bakulchandra <Nehal-Bakulchandra.shah@amd.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The build robot is complaining on Blackfin:
drivers/pinctrl/pinctrl-adi2.c: In function 'port_setup':
>> drivers/pinctrl/pinctrl-adi2.c:221:21: error: dereferencing
pointer to incomplete type 'struct gpio_port_t'
writew(readw(®s->port_fer) & ~BIT(offset),
^~
drivers/pinctrl/pinctrl-adi2.c: In function 'adi_gpio_ack_irq':
>> drivers/pinctrl/pinctrl-adi2.c:266:18: error: dereferencing
pointer to incomplete type 'struct bfin_pint_regs'
if (readl(®s->invert_set) & pintbit)
^~
It seems the driver need to include <asm/gpio.h> and <asm/irq.h>
to compile.
The Blackfin architecture was re-defining the Kconfig
PINCTRL symbol which is not OK, so replaced this with
PINCTRL_BLACKFIN_ADI2 which selects PINCTRL and PINCTRL_ADI2
just like most arches do.
Further, the old GPIO driver symbol GPIO_ADI was possible to
select at the same time as selecting PINCTRL. This was not
working because the arch-local <asm/gpio.h> header contains
an explicit #ifndef PINCTRL clause making compilation break
if you combine them. The same is true for DEBUG_MMRS.
Make sure the ADI2 pinctrl driver is not selected at the same
time as the old GPIO implementation. (This should be converted
to use gpiolib or pincontrol and move to drivers/...) Also make
sure the old GPIO_ADI driver or DEBUG_MMRS is not selected at
the same time as the new PINCTRL implementation, and only make
PINCTRL_ADI2 selectable for the Blackfin families that actually
have it.
This way it is still possible to add e.g. I2C-based pin
control expanders on the Blackfin.
Cc: Steven Miao <realmz6@gmail.com>
Cc: Huanhuan Feng <huanhuan.feng@analog.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change prepare the introduction of new meson SoC. This new SoC will
share the same gpio/pinconf registers but the pinmux part will be
different. While the format of the data associated with each pinmux group
will change, the way to handle pinmuxing will be similar.
To deal with this new situation, the meson_pmx_struture is kept but the
data associated to it is now generic. This allows to reuse the basic
functions which would otherwise be copy/pasted in each pinmux driver
(such as getting the name a count of groups and functions) Only the
functions actually using this specific data is taken out of the common
code and is handling the SoC pinmuxing
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When meson pinctrl is enabled, all meson platforms pinctrl drivers are
built in the kernel, with a significant amount of data.
This leads to situation where pinctrl drivers targeting an architecture
are also compiled and shipped on another one (ex: meson8 - ARM - compiled
and shipped on ARM64 builds). This is a waste of memory we can easily
avoid.
This change makes 4 pinctrl drivers (1 per SoC) out the original single
driver, allowing to compile and ship only the ones required.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Voltage switching is the same as on the r8a7794.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car Gen3 Hardware Manual Errata for Rev 0.55 of September 8, 2017
removed the USB0_IDIN and USB0_IDPU pins on R-Car D3.
This change has no functional impact, as these definitions were unused.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Some two functions were missing from the Gemini pin control
driver. Noticed when trying to use ethernet. Fix it up by
adding them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of depends on GPIOLIB and having to run around in
Kconfig menus looking for why your device is not available,
simply select it from the pin control drivers that need it.
The Kconfig for GPIOLIB is improved, selectable and this
should "just work".
Cc: Phil Reid <preid@electromag.com.au>
Cc: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Cc: Peter Rosin <peda@axentia.se>
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most pins on the r8a7796 SoC can be configured in GPIO mode for
interrupt and GPIO functionality, while a couple of them can also
be routed to the INTC-EX hardware block (formerly known as IRQC).
On r8a7795 the INTC-EX hardware handles pins IRQ0 -> IRQ5 and
this patch adds support for them to the PFC driver as "intc_ex_irqN".
[takeshi.kihara.df: Ported from commit bb46f6f3f3 ("pinctrl: sh-pfc:
r8a7795: Add support for INTC-EX IRQ pins")
to drivers/pinctrl/sh-pfc/pfc-r8a7796.c]
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and a function for the INTC-EX interrupt controller on
R-Car H3 ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
GPIO is expected to be disabled iff PIN_CONFIG_BIAS_HIGH_IMPEDANCE is
configured. Update is_enabled flag in config_set() so that it can
reflect GPIO status correctly. Also modify EN_CTL register based on
is_enabled flag in config_set() to configure the GPIO properly.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Variable mask and val are not used in the mcp_pinconf_set().
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This allows PINCTRL to be selected manually to allow enabling of the
mcp23s08 i2c/spi gpio driver. Which is not platform specific.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While removing the need to have pin_base defined in meson pinctrl
drivers, I forgot to remove the corresponding field from the
pinctrl_data structure.
Fixing this now.
Fixes: 70e5ecb1b9 ("pinctrl: meson: get rid of pin_base")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add TEST_N pinmux for channel 6 and 7 of the i2s output
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The structure sx150x_regmap_config is local to the source and does not
need to be in global scope, so make it static.
Cleans up sparse warning:
symbol 'sx150x_regmap_config' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function ingenic_pinctrl_probe is local to the source and does
not need to be in global scope, so make it static.
Cleans up sparse warnings
symbol 'ingenic_pinctrl_probe' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Aspects like the number of ports and the location where peripherals are
brought out differ between the RZ/A1H and RZ/A1L.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
New GPIO IRQs are allocated and mapped dynamically by default when
GPIO IRQ infrastructure is used by cherryview-pinctrl driver.
This causes issues on some Intel platforms [1][2] with broken BIOS which
hardcodes Linux IRQ numbers in their ACPI tables.
On such platforms cherryview-pinctrl driver should allocate and map all
GPIO IRQs at probe time.
Side effect - "Cannot allocate irq_descs @ IRQ%d, assuming pre-allocated\n"
can be seen at boot log.
NOTE. It still may fail if boot sequence will changed and some interrupt
controller will be probed before cherryview-pinctrl which will shift Linux IRQ
numbering (expected with CONFIG_SPARCE_IRQ enabled).
[1] https://bugzilla.kernel.org/show_bug.cgi?id=194945
[2] https://lkml.org/lkml/2017/9/28/153
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Chris Gorman <chrisjohgorman@gmail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reported-by: Chris Gorman <chrisjohgorman@gmail.com>
Reported-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add SDHI and DRIF pin groups on R-Car H3 ES2.0,
- Add USB3.0 host pin groups on R-Car H3 (ES1.x and ES2.0),
- Add EthernetAVB and USB2.0 host pin groups on R-Car D3.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C/IT
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.15-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.15
- Add SDHI and DRIF pin groups on R-Car H3 ES2.0,
- Add USB3.0 host pin groups on R-Car H3 (ES1.x and ES2.0),
- Add EthernetAVB and USB2.0 host pin groups on R-Car D3.
If the gmac-m1 optimization(bit10) is selected, the gpio function
of gmac pins is not valid. We may use the rmii mode for gmac interface,
the pins such as rx_d2, rx_d3, which the rgmii mode used, but rmii not
used could be taken as gpio function. So gmac_rxd0m1 selects the bit2,
and gmac_rxd0m3 select bit10 is more correct.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset of gpio0 and gpio1 bank drive strength is 0x8, not 0x4.
But the mux is 0x4, we couldn't use the IOMUX_WIDTH_4BIT flag, so
we give them actual offset.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These request/free functions are just reimplementations of the
standard helpers in gpiolib. Delete them and replace with the
helpers.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIOX_22 is declared as a gpio but the id is no present in the pin
table. This hole trigger an error while reading the pingroup debugfs entry
GPIOX_22 is no routed externally. For all we know, it could an internal
pin of SoC
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On meson-gx platforms, TEST_N has been incorrectly declared in the EE
controller while it belongs to AO controller.
Move the pin to the appropriate controller
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pin_base was used with the manually set pin offset in meson pinctrl. This
is no longer the case, pin_base is 0 on every meson pinctrl controllers
and should go away.
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Offset on meson pinctrl and gpios is something that was carried from the
vendor driver, where there is a weird link between the 2
controllers. Since these 2 controllers are independent, this offset adds
an unnecessary complexity.
This patch remove this manually set offset and rely on pinctrl to figure
out the gpio base offset
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since pinmuxing for I2C is equal on H3 ES1.0 and later versions, copy
the I2C settings from ES1.0. Fixes this error in upstream for
Salvator-XS:
sh-pfc e6060000.pin-controller: function 'i2c2' not supported
sh-pfc e6060000.pin-controller: invalid function i2c2 in map table
i2c-rcar: probe of e6510000.i2c failed with error -22
Now, the bus works the same as with other Salvator boards.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds support for PWM on r8a77995.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The commit 79d2c8bede ("pinctrl/amd: save pin registers over
suspend/resume") caused the following compilation errors:
drivers/pinctrl/pinctrl-amd.c: In function ‘amd_gpio_should_save’:
drivers/pinctrl/pinctrl-amd.c:741:8: error: ‘const struct pin_desc’ has no member named ‘mux_owner’
if (pd->mux_owner || pd->gpio_owner ||
^
drivers/pinctrl/pinctrl-amd.c:741:25: error: ‘const struct pin_desc’ has no member named ‘gpio_owner’
if (pd->mux_owner || pd->gpio_owner ||
We need to enable CONFIG_PINMUX for this driver as well.
Cc: stable@vger.kernel.org
Fixes: 79d2c8bede ("pinctrl/amd: save pin registers over suspend/resume")
Signed-off-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixed typo on comment for north_community.
Signed-off-by: Chris Gorman <chrisjohgorman@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_domain_ops.activate() callback has no return value and no way to
tell the function that the activation is early.
The upcoming changes to support a reservation scheme which allows to assign
interrupt vectors on x86 only when the interrupt is actually requested
requires:
- A return value, so activation can fail at request_irq() time
- Information that the activate invocation is early, i.e. before
request_irq().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Juergen Gross <jgross@suse.com>
Tested-by: Yu Chen <yu.c.chen@intel.com>
Acked-by: Juergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213152.848490816@linutronix.de
The pinctrl_request_gpio() and pinctrl_free_gpio() break the nice
namespacing in the other cross-calls like pinctrl_gpio_foo().
Just rename them and all references so we have one namespace
with all cross-calls under pinctrl_gpio_*().
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ENOSYS is special and should only be used for incorrect syscall number.
It is not the case here. let's use ENOTSUPP instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fix the following build warning:
drivers/pinctrl/bcm/pinctrl-bcm2835.c:376:15: warning: variable 'type' set but not used [-Wunused-but-set-variable]
Furthermore, it is unused for a long time, at least since commit 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
where a "FIXME no clue why the code looks up the type here" was added.
A year after, nobody answeered this question, so its time to remove it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Don't populate the read-only arrays prop2 and prop4 on the stack, instead
make them static const. Makes the object code smaller by over 230 bytes:
Before:
text data bss dec hex filename
28235 5820 192 34247 85c7 drivers/pinctrl/pinctrl-single.o
After:
text data bss dec hex filename
27839 5980 192 34011 84db drivers/pinctrl/pinctrl-single.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The functions amd_gpio_suspend and amd_gpio_resume are local to the
source and do not need to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'amd_gpio_suspend' was not declared. Should it be static?
symbol 'amd_gpio_resume' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
DRIF support for r8a7795 was initially added with commit 2d77583198
("pinctrl: sh-pfc: r8a7795: Add DRIF support") and later dropped from
the new pfc-r8a7795.c while re-naming the initial pfc-r8a7795.c to
pfc-r8a7795-es1.c in commit b205914c8f ("pinctrl: sh-pfc: r8a7795:
Add support for R-Car H3 ES2.0"). As the DRIF doesn't differ, re-add
it here.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add SDHI0-3 support for R-Car H3 ES2.0 based on a patch from the Renesas
BSP. SDHI pin config is identical to H3 ES1.*.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Don't populate const arrays on the stack, instead make them
static. Makes the object code smaller nearly 1000 bytes. Also
line break wide lines to avoid checkpatch warnings.
Before:
text data bss dec hex filename
13112 1996 0 15108 3b04 pinctrl-uniphier-core.o
After:
text data bss dec hex filename
11642 2476 0 14118 3726 pinctrl-uniphier-core.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The touchpad in the Asus laptop models X505BA/BP and X542BA/BP is
unresponsive after suspend/resume. The following error appears during
resume:
i2c_hid i2c-ELAN1300:00: failed to reset device.
The problem here is that i2c_hid does not notice the interrupt being
generated at this point, because the GPIO is no longer configured
for interrupts.
Fix this by saving pinctrl-amd pin registers during suspend and
restoring them at resume time.
Based on code from pinctrl-intel.
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Drake <drake@endlessm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit dc749a09ea ("gpiolib: allow gpio irqchip to map irqs
dynamically"), the irqs for gpio are not statically allocated during in
gpiochip_irqchip_add.
This driver was based on this assumption for initializing the mask
associated to each interrupt this led to a NULL pointer crash in the
kernel:
Unable to handle kernel NULL pointer dereference at virtual address 00000000
Mem abort info:
Exception class = DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
Data abort info:
ISV = 0, ISS = 0x00000068
CM = 0, WnR = 1
[0000000000000000] user address but active_mm is swapper
Internal error: Oops: 96000044 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.13.0-06657-g3b9f8ed25dbe #576
Hardware name: Marvell Armada 3720 Development Board DB-88F3720-DDR3 (DT)
task: ffff80001d908000 task.stack: ffff000008068000
PC is at armada_37xx_pinctrl_probe+0x5f8/0x670
LR is at armada_37xx_pinctrl_probe+0x5e8/0x670
pc : [<ffff000008e25cdc>] lr : [<ffff000008e25ccc>] pstate: 60000045
sp : ffff00000806bb80
x29: ffff00000806bb80 x28: 0000000000000024
x27: 000000000000000c x26: 0000000000000001
x25: ffff80001efee760 x24: 0000000000000000
x23: ffff80001db6f570 x22: ffff80001db6f438
x21: 0000000000000000 x20: ffff80001d9f4810
x19: ffff80001db6f418 x18: 0000000000000000
x17: 0000000000000001 x16: 0000000000000019
x15: ffffffffffffffff x14: 0140000000000000
x13: 0000000000000000 x12: 0000000000000030
x11: 0101010101010101 x10: 0000000000000040
x9 : ffff000009923580 x8 : ffff80001d400248
x7 : ffff80001d400270 x6 : 0000000000000000
x5 : ffff80001d400248 x4 : ffff80001d400270
x3 : 0000000000000000 x2 : 0000000000000001
x1 : 0000000000000001 x0 : 0000000000000000
Process swapper/0 (pid: 1, stack limit = 0xffff000008068000)
Call trace:
Exception stack(0xffff00000806ba40 to 0xffff00000806bb80)
ba40: 0000000000000000 0000000000000001 0000000000000001 0000000000000000
ba60: ffff80001d400270 ffff80001d400248 0000000000000000 ffff80001d400270
ba80: ffff80001d400248 ffff000009923580 0000000000000040 0101010101010101
baa0: 0000000000000030 0000000000000000 0140000000000000 ffffffffffffffff
bac0: 0000000000000019 0000000000000001 0000000000000000 ffff80001db6f418
bae0: ffff80001d9f4810 0000000000000000 ffff80001db6f438 ffff80001db6f570
bb00: 0000000000000000 ffff80001efee760 0000000000000001 000000000000000c
bb20: 0000000000000024 ffff00000806bb80 ffff000008e25ccc ffff00000806bb80
bb40: ffff000008e25cdc 0000000060000045 ffff00000806bb60 ffff0000081189b8
bb60: ffffffffffffffff ffff00000811cf1c ffff00000806bb80 ffff000008e25cdc
[<ffff000008e25cdc>] armada_37xx_pinctrl_probe+0x5f8/0x670
[<ffff00000859d8c8>] platform_drv_probe+0x58/0xb8
[<ffff00000859bb44>] driver_probe_device+0x22c/0x2d8
[<ffff00000859bcac>] __driver_attach+0xbc/0xc0
[<ffff000008599c84>] bus_for_each_dev+0x4c/0x98
[<ffff00000859b440>] driver_attach+0x20/0x28
[<ffff00000859af90>] bus_add_driver+0x1b8/0x228
[<ffff00000859c648>] driver_register+0x60/0xf8
[<ffff00000859df64>] __platform_driver_probe+0x74/0x130
[<ffff000008e256dc>] armada_37xx_pinctrl_driver_init+0x20/0x28
[<ffff000008083980>] do_one_initcall+0x38/0x128
[<ffff000008e00cf4>] kernel_init_freeable+0x188/0x22c
[<ffff0000089b56e8>] kernel_init+0x10/0x100
[<ffff000008084bb0>] ret_from_fork+0x10/0x18
Code: f9403fa2 12001341 1100075a 9ac12041 (b9000001)
---[ end trace 8b0f4e05e1603208 ]---
This patch moves the initialization of the mask field in the irq_startup
function. However some callbacks such as irq_set_type and irq_set_wake
could be called before irq_startup. For those functions the mask is
computed at each call which is not a issue as these functions are not
located in a hot path but are used sporadically for configuration.
Fixes: dc749a09ea ("gpiolib: allow gpio irqchip to map irqs
dynamically")
Cc: <stable@vger.kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
info->groups[] has info->ngroups elements so these comparisons should be
>= instead of >.
Fixes: 41d32cfce1 ("pinctrl: sprd: Add Spreadtrum pin control driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_pinctrl_get() could fail with ERR_PTR(-ENOMEM) so I have added a
check for that. I also reversed the other IS_ERR() test because it was
a little confusing to test one way and then the opposite a couple lines
later.
Fixes: 41d32cfce1 ("pinctrl: sprd: Add Spreadtrum pin control driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Spreadtrum pinctrl drivers are only useful when building for a
Spreadtrum platform.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix build errors when CONFIG_OF is not enabled.
Also, the pinctrl-sprd-sc9860 driver uses functions from the pinctrl-sprd
driver, so the former should depend on the latter driver.
../drivers/pinctrl/sprd/pinctrl-sprd.c: In function 'sprd_dt_node_to_map':
../drivers/pinctrl/sprd/pinctrl-sprd.c:290:2: error: implicit declaration of function 'pinconf_generic_parse_dt_config' [-Werror=implicit-function-declaration]
ret = pinconf_generic_parse_dt_config(np, pctldev, &configs,
^
../drivers/pinctrl/sprd/pinctrl-sprd.c: At top level:
../drivers/pinctrl/sprd/pinctrl-sprd.c:844:44: error: array type has incomplete element type
static const struct pinconf_generic_params sprd_dt_params[] = {
^
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Baolin Wang <baolin.wang@spreadtrum.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The functions sprd_pmx_get_function_count, sprd_pmx_get_function_name
and sprd_pmx_get_function_groups are local to the source and do not
need to be in global scope, so make them static.
Cleans up sparse warnings:
"symbol 'sprd_pmx_get_function_count' was not declared. Should it be
static?"
"symbol 'sprd_pmx_get_function_name' was not declared. Should it be
static?"
"symbol 'sprd_pmx_get_function_groups' was not declared. Should it be
static?"
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The #includes <linux/bug.h> is here to use BUILD_BUG_ON_ZERO().
Thanks to commit bc6245e5ef ("bug: split BUILD_BUG stuff out into
<linux/build_bug.h>"), it is now possible to reduce the number of
headers pulled in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
- New Device Support
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
- New Functionality
- Amend API to provide register layout; atmel-smc
- Fix-ups
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
- Bug Fixes
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll
-----BEGIN PGP SIGNATURE-----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=TKIm
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
This reverts commit 2154d94b40.
The original patch was intented to avoid some issues with the sunxi
gpio rework and was supposed to be reverted after all the required
DT bits had been merged around v4.10.
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ether_rmii_groups should have "ether_rmii" and "ether_rmiib" as
members. This patch replaces to them.
Fixes: 1e359ab128 ("pinctrl: uniphier: add Ethernet pin-mux settings")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in these functions.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In the same way as it's done in pinctrl-cherryview.c we would provide
a readback TX buffer state.
Fixes: 17fab47369 ("pinctrl: intel: Set pin direction properly")
Reported-by: "Bourque, Francis" <francis.bourque@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: "Bourque, Francis" <francis.bourque@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pins from GPIO1A0 to GPIO1B1 are special, need to recalculate
iomux. And the register offset is larger than the u8 range, so changed
to u32.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Decrease indentation in intel_gpio_set() to make it looking slightly better
and be in align with intel_gpio_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The OF node name already contains the gpio chip identifier, no need to
append it when creating the label.
The following debug message clearly shows the suffix is not required
"pinctrl-rza1 fcfe3000.pin-controller: Parsed gpiochip gpio-0-0 with 6
pins"
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Power source selection in DIG_VIN_CTL is indexed from 0, in the range
check it shouldn't be equal to the total number of power sources.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make these const as they are only stored in the const field of a
mxs_pinctrl_soc_data structure.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Yong Li found that writes to the AST2500 strapping register were not
properly supported by the Aspeed pinctrl core and provided a patch to
rectify the problem. Several revisions of the patch were posted and
ultimately v4 should have been applied, however some unfortunate
liberal application of tags on my part lead to confusion between v3[1]
and v4[2].
Generate the diff between v3 and v4 to apply as a fixup patch.
[1] http://patchwork.ozlabs.org/patch/801662/
[2] http://patchwork.ozlabs.org/patch/802946/
Cc: Yong Li <sdliyong@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The rza1_pctl->ports[] array has RZA1_NPORTS (12) elements. The > here
should be >= to prevent an out of bounds access.
Fixes: 5a49b644b3 ("pinctrl: Renesas RZ/A1 pin and gpio controller")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds the pin control driver for Spreadtrum SC9860 platform.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In some scenarios, we should set some pins as input/output/pullup/pulldown
when the specified system goes into deep sleep mode, then when the system
goes into deep sleep mode, these pins will be set automatically by hardware.
That means some pins are not controlled by any specific driver in the OS, but
need to be controlled when entering sleep mode. Thus we introduce one sleep
state config into pinconf-generic for users to configure.
Signed-off-by: Baolin Wang <baolin.wang@spreadtrum.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MT2701 shares the same driver with MT7623, but there is a slight difference
between their pin functions (e.g., PCIe), so we update the different parts
in pinmux table.
Doing so, SoC could choose the correct mux setting via their own pinfun.h.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Cc: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Intel Lewisburg has the same GPIO hardware than Intel Sunrisepoint-H
except few differences in register offsets and pin lists. Because of
this we add a separate pinctrl driver for Lewisburg.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is desktop version Intel Cannon Lake PCH. The GPIO hardware is the
same but pin list differs a bit. Add support for this to the existing
Cannon Lake pin controller driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Propagate errors on group config, now r8a7740-armadillo800eva.dts is
fixed,
- Add MSIOF and USB2.0 pin groups on R-Car H3 ES2.0,
- Add USB2.0 and USB3.0 pin groups on R-Car M3-W,
- Add a missing MMC pin group on R-Car M2-W and RZ/G1M,
- Add initial support for R-Car D3,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=xgLM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.14-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.14
- Propagate errors on group config, now r8a7740-armadillo800eva.dts is
fixed,
- Add MSIOF and USB2.0 pin groups on R-Car H3 ES2.0,
- Add USB2.0 and USB3.0 pin groups on R-Car M3-W,
- Add a missing MMC pin group on R-Car M2-W and RZ/G1M,
- Add initial support for R-Car D3,
- Small fixes and cleanups.
On AST2500, the hardware strap register(SCU70) only accepts write ‘1’,
to clear it to ‘0’, must set bits(write ‘1’) to SCU7C
Signed-off-by: Yong Li <sdliyong@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pin controller of Allwinner H5 has three IRQ banks, however in old
versions of drivers and device trees, only two are set, which makes
PG bank IRQ not available.
If it's directly set to 3, the old device trees will fail to boot.
Add a workaround (and a warning) for older device trees, and allow new
device trees to use correct 3 IRQ banks.
Fixes: 838adb576d ("drivers: pinctrl: add driver for Allwinner H5 SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The fix prevents unintended wakes from second level GPIO pin interrupts.
On some Intel Kabylake platforms, it is observed that GPIO pin interrupts
can wake the platform from suspend-to-idle, even though the IRQ is not
configured as IRQF_NO_SUSPEND or enable_irq_wake().
This can cause undesired wakes on Mobile devices such as Laptops and
Chromebook devices. For example a headset jack insertion is not a desired
wake source on Chromebook devices.
The pinctrl-intel (GPIO controller) driver implements a "Shared IRQ" model.
All GPIO pin interrupts are OR'ed and mapped to a first level IRQ14 (or
IRQ15). The driver registers an irq_chip struct and maps an irq_domain for
the GPIO pin interrupts. The IRQ14 handler demuxes and calls the second
level IRQ for the respective pin.
In the suspend entry flow, at suspend_noirq stage, the kernel disables IRQs
that are not marked for wake. The pinctrl-intel driver does not implement a
irq_disable() callback (to take advantage of lazy disabling). The
pinctrl-intel GPIO interrupts are not disabled in hardware during suspend
entry, and thus are able to wake the SoC out of suspend-to-idle.
This patch sets the IRQCHIP_MASK_ON_SUSPEND flag for the GPIO irq_chip, to
disable the second level interrupts at suspend_noirq stage via the irq_mask
callbacks. The irq_mask callback disables the IRQs in hardware by
programming the corresponding GPIO pad registers. Only IRQs that are not
marked for wake are disabled.
Signed-off-by: Rushikesh S Kadam <rushikesh.s.kadam@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-and-tested-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops and pctlops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (pctlops and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinmux_ops structure is only stored in the const pmxops field
of a pinctrl_desc structure. Make the pinmux_ops structure const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (pctlops and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (pctlops and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (pctlops and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinmux_ops structure is only stored in the const pmxops field
of a pinctrl_desc structure. Make the pinmux_ops structure const as
well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinconf_ops structure is only stored in the const pinconf_ops
field of a pinctrl_desc structure. Make the pinconf_ops structure
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinctrl_ops structure is only stored in the const pctlops
field of a pinctrl_desc structure. Make the pinctrl_ops structure
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Lars Persson <lars.persson@axis.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This pinconf_ops structure is only stored in the const confops
field of a pinctrl_desc structure. Make the pinconf_ops structure
const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_irq() returns an error code, but the pinctrl-amd driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.
Print and propagate the return value of platform_get_irq on failure.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RK805 is one of Rockchip PMICs family, it has 2 output only GPIOs.
This driver is also designed for other Rockchip PMICs to expend.
Different PMIC maybe have different pin features, for example,
RK816 has one pin which can be used for TS or GPIO(input/out).
The mainly difference between PMICs pins are pinmux, direction
and output value, that is 'struct rk805_pin_config'.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This follows the style of existion PORT_GP_X macros and
will be used by a follow-up patch for the r8a77995 SoC.
Extracted from the initial r8a77995 patch in the BSP by Takeshi Kihara.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds USB30 (USB3.0 host) pin, group and function to R8A7796
SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This is a correction because MOD_SEL register specification for R8A7795
ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch renames the pin function macro definitions of the GPSR1 and
IPSR4 registers value for the CS1# pin.
This is a correction because GPSR and IPSR register specification for
R8A7795 ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual
Rev.0.54E.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of FSCLKST pins function and IPSR7
bit[15:12] register deleted.
This is a correction because IPSR register specification for R8A7795
ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E or
later.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes to set MOD_SEL2 bit19 when using TCLK2_A pin function is
selected for IPSR16 bit[23:20] or using TCLK2_B pin function is selected
for IPSR17 bit[27:24]. And renames MOD_SEL2 bit26 value definition name
to SEL_TIMER_TMU1.
This is a correction because MOD_SEL register specification for R8A7795
ES2.0 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of IPSR register value
definitions for NFDATA{0..13} and NF{ALE,CLE,WE_N,RE_N} pins function.
This is a correction to the incorrect implementation of IPSR register pin
assignment of the specifications updated for R8A7795 ES2.0 SoC in R-Car
Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of IPSR register value
definitions for FMCLK{_C,_D} and FMIN{_C,_D} pins function.
This is a correction to the incorrect implementation of IPSR register pin
assignment of the specifications updated for R8A7795 ES2.0 SoC in R-Car
Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes SCIF_CLK_{A,B} pin's MOD_SEL assignment from MOD_SEL1
bit11 to MOD_SEL1 bit10.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7795 ES2.0 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.53E or later.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL2 bit26 value
when SCK5_A pin function is selected for IPSR16 bit[31:28].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7795 ES2.0 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL1 bit[25:24]
value when STP_ISEN_1_D pin function is selected for IPSR17 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7795 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: 0b0ffc96db ("pinctrl: sh-pfc: Initial R8A7795 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and functions for USB 2.0 on R-Car H3 ES2.0.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since the latest datasheet revises the names, this patch changes
the definitions from USB3_{OVC,PWEN} to USB2_CH3_{OVC,PWEN}.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add property "qcom,dtest-buffer" to specify which dtest rail to feed
when the pin is configured as a digital input.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.
Signed-off-by: Fenglin Wu <fenglinw@codeaurora.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1. Fix NULL pointer dereference on S3C24XX. This was reported some time ago and
unfortunately it took few releases to fix.
2. Fix invalid register offset used for external interrupts on Exynos5433.
This was caused by the same commit as above, although on different path.
3. Consolidate between drivers and bindings the defines for pin mux functions.
4. Minor code improvements.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=eAr5
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl driver changes for v4.14:
1. Fix NULL pointer dereference on S3C24XX. This was reported some time ago and
unfortunately it took few releases to fix.
2. Fix invalid register offset used for external interrupts on Exynos5433.
This was caused by the same commit as above, although on different path.
3. Consolidate between drivers and bindings the defines for pin mux functions.
4. Minor code improvements.
This adds a pin control (only multiplexing) driver for the Gemini
SoC so we can sort out this complex platform in an orderly manner.
This driver will detect the chip/package version as SL3512 or SL3516
(also known as CS3512 and CS3516 etc) and register the apropriate
pin set.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
pinconf_set_config() is called by pinctrl_gpio_set_config().
If a GPIO driver is backed by a pinctrl driver and it does not
support .pin_config_set() hook, it causes NULL pointer dereference.
Fixes: 15381bc7c7 ("pinctrl: Allow configuration of pins from gpiolib based drivers")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver adds pinctrl/GPIO support for Intel Denverton SoC. The GPIO
controller is based on the same hardware design that is already used in
Intel Sunrisepoint so we leverage the core driver here.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 58957d2edf ("pinctrl: Widen the generic pinconf argument
from 16 to 24 bits"), the generic pinconf arguments are handled by u32.
UniPhier pinctrl drivers do not support debouncing, so u16 is working,
but align the argument type to u32 for consistency.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The V3s pin controller doesn't have the bank 0 (starts at address
0x200), which is like A33. However, this is not worked around when
developing the driver, which makes IRQ not working.
Fix the IRQ bank base.
Fixes: 56d9e4a760 ("pinctrl: sunxi: add driver for V3s SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the ST driver still only regards
0 as failure indication -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some pins like i2c SCL/SDA need the schmitt input function
to avoid crosstalk problems.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel pin control drivers are architecture specific so add an if arch
to check for X86 or compile test to ensure continued test coverage.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
of_irq_get() may return any negative error number as well as 0 on failure,
while the driver only checks for -EPROBE_DEFER, blithely continuing with
the call to gpiochip_set_chained_irqchip() -- that function expects the
parent IRQ as *unsigned int*, so would probably do nothing when a large
IRQ number resulting from a conversion of a negative error number is passed
to it, however passing 0 would probably work but the driver won't receive
valid GPIO bank interrupts.
Check for 'ret <= 0' instead and return -ENXIO from the driver's probe iff
of_irq_get() returned 0.
Fixes: f936779329 ("pinctrl: sirf: add sirf atlas7 pinctrl and gpio support")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 3 IP blocks pin routes need to be switched, that are
emmc-cmd, spi, i2s. And there are some pins need to be recalced,
which are gpio2c4~gpio2c7 and gpio2d0.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The other Socs also need the feature of recalced iomux, so
make it as a common interface like iomux route feature.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The irq_group field stores a 1:1 mapping. Use the loop variable to
derive the values instead of storing them in an extra array.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO offset is never initialized, which means that it will end up
being zero as per the devm_kzalloc() of the parent structure.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee@kernel.org>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Barry Song <baohua@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: kernel@stlinux.com
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: linux-gpio@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the AST2500 USB functions as described by the devicetree
bindings. The AST2500 exposes five USB controllers through two USB
ports. Similar to the AST2400, the pins exposing USB are outliers with
respect to the rest of the pinmux as they not capable of GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the AST2400 USB functions as described by the devicetree
bindings. Three ports are fully documented in the datasheet and exposed
through the bindings and pinctrl, though there are remnants of
documentation for a fourth port muxed with GPIO pins GPIOQ6 and GPIOQ7.
The implementation is updated to reflect this but the function and
group are not exposed.
Disregarding the mostly undocumented fourth port, the USB functions are
an outlier with respect to the rest of the muxed functionality on the
AST2400 as GPIO is not supported on these pins.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It fixes the following Smatch static check warning:
drivers/pinctrl/zte/pinctrl-zx.c:338 zx_pinctrl_build_state()
warn: passing devm_ allocated variable to kfree.
As we will be calling krealloc() on pointer 'functions', which means
kfree() will be called in there, devm_kzalloc() shouldn't be used with
the allocation in the first place. Fix the warning by calling kcalloc()
and managing the free procedure in error path on our own.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: cbff0c4d27 ("pinctrl: add ZTE ZX pinctrl driver support")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
15136 5112 0 20248 4f18 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
after:
bss dec hex filename
14849 5024 0 19873 4da1 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
18958 9000 128 28086 6db6 drivers/pinctrl/bcm/pinctrl-bcm2835.o
after:
text data bss dec hex filename
18764 8912 128 27804 6c9c drivers/pinctrl/bcm/pinctrl-bcm2835.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the below warning
--> Prefer 'unsigned int' to bare use of 'unsigned'.
--> line over 80 characters.
--> Prefer 'unsigned int **' to bare use of 'unsigned **'.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the kernel doc warnings in the driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
21671 3632 128 25431 6357 drivers/pinctrl/pinctrl-st.o
after:
text data bss dec hex filename
21366 3576 128 25070 61ee drivers/pinctrl/pinctrl-st.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WARN_ON causes a backtrace to get logged which is only useful for
kernel bugs. For signalling a firmware bug dev_warn(dev, FW_BUG "...")
should be used.
This fixes users running userspace software to monitor kernel oopses
getting a false positive bug-report every boot because of the wrong
use of WARN_ON.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Various IMX platforms may have different imx_pmx_ops.gpio_set_direction
implementations, so let's make it platform specific callbacks instead of
the fixed common one.
Currently only VF610 platform implements it. No function level changes.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_request_enable/disable_free actually are not quite necessary as
standard IMX pinctrl binding already sets GPIO mux from device tree,
e.g. VF610_PAD_PTB20__GPIO_42 or MX7D_PAD_SD2_CD_B__GPIO5_IO9
No need to do it again in gpio_request_enable.
And according to Stefan:
"For all GPIO I checked in upstream device trees we assign a pinctrl
to the same node, so in all cases gpio_request_enable/disable is really
unnecessary."
So it should be safe to simply remove it.
Note that this changes semantics for Vybrid, e.g.
"The two functions have been introduced for Vybrid (through
SHARE_MUX_CONF_REG) and mux pins as GPIOs automatically when a GPIO
gets requested. The automatic mux is optional by the pinmux/gpio
subsystem semantics, and other NXP devices do not use it, instead an
explicit pinctrl node is added in the device tree to mux GPIOs where
required. Hence this change aligns Vybrid to other NXP (i.MX) devices.
Note that all upstream device tree assign proper pinctrl properties
where GPIOs are used so no change is necessary for device trees."
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i.MX 7ULP has three IOMUXC instances: IOMUXC0 for M4 ports,
IOMUXC1 for A7 ports and IOMUXC DDR for DDR interface.
This patch adds the IOMUXC1 support for A7.
It only supports generic pin config.
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pinmux property seems to be more suitable for IMX.
So we change to use 'pinmux' instead of 'pins'.
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Save registers lost in the sleep when suspending, and restore them
when resuming.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/20 SoCs (capable of per-pin input enable), the iectrl bit
number matches its pin number. So, this is redundant information.
Instead, we just need a flag to know if the iectrl gating exists or not.
With this refactoring, 5 bits in pin data will be saved.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a bunch of GPIO muxing data, but most of them are actually
unneeded because GPIO-to-pin mapping can be specified by "gpio-ranges"
DT properties.
Tables that contain a set of GPIO pins are still needed for the named
mapping by "gpio-ranges-group-names". This is a much cleaner way for
UniPhier SoC family where GPIO numbers are not straight mapped to pin
numbers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/LD20 SoCs (capable of per-pin input enable), iectrl bits are
located across multiple registers. So, the register offset must be
taken into account. Otherwise, wrong input-enable status is displayed.
While we here, rename the macro because it is a base address.
Fixes: aa543888ca ("pinctrl: uniphier: support per-pin input enable for new SoCs")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All UniPhier pinctrl drivers are built-in. Exporting the symbol
is meaningless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
13129 2808 192 16129 3f01 drivers/pinctrl/qcom/pinctrl-msm.o
after:
text data bss dec hex filename
12839 2720 192 15751 3d87 drivers/pinctrl/qcom/pinctrl-msm.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17061 6992 0 24053 5df5 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
after:
text data bss dec hex filename
16777 6904 0 23681 5c81 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
12775 3696 64 16535 4097 drivers/pinctrl/pinctrl-coh901.o
after:
bss dec hex filename
12440 3640 64 16144 3f10 drivers/pinctrl/pinctrl-coh901.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17545 5376 0 22921 5989 drivers/pinctrl/nomadik/pinctrl-abx500.o
after:
bss dec hex filename
17273 5320 0 22593 5841 drivers/pinctrl/nomadik/pinctrl-abx500.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
7754 2328 0 10082 2762 drivers/pinctrl/vt8500/pinctrl-wmt.o
after:
text data bss dec hex filename
7472 2272 0 9744 2610 drivers/pinctrl/vt8500/pinctrl-wmt.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
11866 3520 128 15514 3c9a drivers/pinctrl/pinctrl-rza1.o
after:
text data bss dec hex filename
11539 3464 128 15131 3b1b drivers/pinctrl/pinctrl-rza1.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C pin functions in R_PIO used to be named "s_twi".
As we usually use the name "i2c" instead of "twi" in the mainline
kernel, change these names to "s_i2c" for consistency.
The "s_twi" functions are not yet referenced by any device trees in
mainline kernel so I think it's safe to change the name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R40 is said to be an upgrade of A20, and its pin configuration is also
similar to A20 (and thus similar to A10).
Add support for R40 to the A10 pinctrl driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoCs.
As it does not support the keeper state and therefore can't
support bias-bus-hold property.
This patch adds a pull_no_keeper setting which configures the
msm_gpio_pull bits for ipq40xx. This is required to fix the
proper configurations of gpio-pull bits for nand pins mux.
IPQ40xx SoC:
2'b10: Internal pull up enable.
2'b11: Unsupport
For other SoC's:
2'b10: Keeper
2'b11: Pull-Up
Note: Due to pull_no_keeper length, all kerneldoc entries
in the msm_pinctrl_soc_data struct had to be realigned.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds multiple pinctrl functions and mappings
for SDIO, NAND, I2S, WIFI, PCIE, LEDs, etc... that have
been missing from the current minimal version.
This patch has been updated from the original version
that was posted by Ram Chandra Jangir on the LEDE-DEV ML:
<https://patchwork.ozlabs.org/patch/752962/>. A short
summary of the changes are documented in the device-tree
patch of this series:
"dt-bindings: pinctrl: add most other IPQ4019 pin functions and groups"
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix the documentation build as the docs were moved.
- Correct the UART pin list on the Intell Merrifield.
- Fix pin assignment and number of pins on the Marvell Armada
37xx pin controller.
- Cover the Setzer models in the Chromebook DMI quirk in the
Intel cheryview driver so they start working.
- Add the missing "sim" function to the sunxi driver.
- Fix USB pin definitions on Uniphier Pro4.
- Smatch fix for invalid reference in the zx pin control driver.
-----BEGIN PGP SIGNATURE-----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=Dyh5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"These are the pin control fixes I have gathered since the return from
my vacation. They boiled in -next a while so let's get them in.
Apart from the documentation build it is purely driver fixes. Which is
nice. The Intel fixes seem kind of important.
- Fix the documentation build as the docs were moved
- Correct the UART pin list on the Intel Merrifield
- Fix pin assignment and number of pins on the Marvell Armada 37xx
pin controller
- Cover the Setzer models in the Chromebook DMI quirk in the Intel
cheryview driver so they start working
- Add the missing "sim" function to the sunxi driver
- Fix USB pin definitions on Uniphier Pro4
- Smatch fix for invalid reference in the zx pin control driver"
* tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: generic: update references to Documentation/pinctrl.txt
pinctrl: intel: merrifield: Correct UART pin lists
pinctrl: armada-37xx: Fix number of pin in south bridge
pinctrl: armada-37xx: Fix the pin 23 on south bridge
pinctrl: cherryview: Add Setzer models to the Chromebook DMI quirk
pinctrl: sunxi: add a missing function of A10/A20 pinctrl driver
pinctrl: uniphier: fix USB3 pin assignment for Pro4
pinctrl: zte: fix dereference of 'data' in zx_set_mux()
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible with the merge of the commit 07d065abf9 "arm64:
dts: marvell: armada-3720-db: Add vqmmc regulator for SD slot", the gpio
regulator used the gpio 23, due to this the whole rgmii group was setup
to gpio which broke the Ethernet support on the Armada 3720 DB
board. Thanks to this patch, the UHS SD cards (which need the vqmmc)
_and_ the Ethernet work again.
Cc: stable@vger.kernel.org
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support
for Armada 37xx")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one more model to the Chromebook DMI quirk to make it working again.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 2a8209fa68 ("pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems")
Reported-by: mail@abhishek.geek.nz
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers that need IRQ_DOMAIN_HIERARCHY should "select" it, but
drivers/pinctrl/stm32/Kconfig is the only exception that uses
"depends on" syntax. This prevents GPIO drivers from select'ing
IRQ_DOMAIN_HIERARCHY.
For example, if I add "select IRQ_DOMAIN_HIERARCHY" to GPIO_XGENE_SB,
I get the following recursive dependency error.
drivers/gpio/Kconfig:13:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:13: symbol GPIOLIB is selected by PINCTRL_STM32
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:3: symbol PINCTRL_STM32 is selected by PINCTRL_STM32F429
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:11: symbol PINCTRL_STM32F429 depends on IRQ_DOMAIN_HIERARCHY
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
kernel/irq/Kconfig:67: symbol IRQ_DOMAIN_HIERARCHY is selected by GPIO_XGENE_SB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:502: symbol GPIO_XGENE_SB depends on GPIOLIB
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.
This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.
Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.
Fixes: f2821b1ca3 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinctrl assignment for Pro4, each definition of USB#2 and
USB#3 are as follows.
184: USB2VBUS
185: USB2OD
186: USB2ID
187: USB3VBUS
188: USB3OD
USB#2 has an additional pin "USB2ID", but the chip doesn't use this pin
while in host-mode. Considering this pin, the pin definitions for USB#3
should be {187, 188}.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two local variables (shift and reg_con) were initialized to unused
values - they were overwritten just few lines after. Getting rid of
this unused initialization allows dropping other variables and
compacting slightly the code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Unlike for other countable members, the driver used u32 for number of
banks (nr_banks). There is no specific need for using fixed-width
integer in this particular place. Make it consistent.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Number of IO memory resources cannot be negative obviously and the
driver depends silently on this (by iterating from 0 to
nr_ext_resources+1). Make this requirement explicit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
We already have macros for values used by driver and Device Tree
sources for pin mux configuration. Use them instead of duplicating
defines.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When setting the pin function for external interrupts, the driver used
wrong IO memory address base. The pin function register is always under
pctl_base, not the eint_base.
By updating wrong register, the external interrupts for chosen GPIO
would not work at all and some other GPIO might be configured to wrong
value. For example on Exynos5433-based boards, the external interrupts
for gpf{1-5}-X GPIOs should not work at all (driver toggled reserved
registers from ALIVE bank instead).
Platforms other than Exynos5433 should not be affected as eint_base
equals pctl_base in such case.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: <stable@vger.kernel.org>
Reported-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
After commit 8b1bd11c1f ("pinctrl: samsung: Add the support the
multiple IORESOURCE_MEM for one pin-bank"), the S3C24xx (and probably
S3C64xx as well) fails:
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
...
(s3c24xx_demux_eint4_7) from [<c004469c>] (__handle_domain_irq+0x6c/0xcc)
(__handle_domain_irq) from [<c0009444>] (s3c24xx_handle_irq+0x6c/0x12c)
(s3c24xx_handle_irq) from [<c000e5fc>] (__irq_svc+0x5c/0x78)
Mentioned commit moved the pointer to controller's base IO memory address
from each controller's driver data (samsung_pinctrl_drv_data) to per-bank
structure (samsung_pin_bank). The external interrupt demux
handlers (s3c24xx_demux_eint()) tried to get this base address from opaque
pointer stored under irq_chip data:
struct irq_data *irqd = irq_desc_get_irq_data(desc);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
...
pend = readl(bank->eint_base + EINTPEND_REG);
which is wrong because this is hardware irq and it bank was never set
for this irq_chip.
For S3C24xx and S3C64xx, this partially reverts mentioned commit by
bringing back the virt_base stored under each controller's driver data
(samsung_pinctrl_drv_data). This virt_base address will be now
duplicated:
- samsung_pinctrl_drv_data->virt_base: used on S3C24xx and S3C64xx,
- samsung_pin_bank->pctl_base: used on Exynos.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: <stable@vger.kernel.org>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reported-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Lihua Yao <ylhuajnu@163.com>
This patch renames the pin function macro definitions of the GPSR1 and
IPSR4 registers value for the CS1# pin.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes IPSR{12,17,18} and MOD_SEL0 pin assignment for FSO pins
group.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of SATA_DEVSLP_B pins function
deleted.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of FSCLKST pins function and IPSR7
bit[15:12] register deleted.
This is a correction because IPSR register specification for R8A7796 SoC
was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes to set MOD_SEL2 bit19 when using TCLK2_A pin function is
selected for IPSR16 bit[23:20] or using TCLK2_B pin function is selected
for IPSR17 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sean Wang