The LED trigger name for CAN devices is based on the initial
CAN device name, but does never change. The LED trigger name
is not guaranteed to be unique in case of hotplugging CAN devices.
This patch tries to address this problem by modifying the
LED trigger name according to the CAN device name when
the latter changes.
v1 - Kurt Van Dijck
v2 - Fabio Baltieri
- remove rename blocking if trigger is bound
- use led-subsystem function for the actual rename (still WiP)
- call init/exit functions from dev.c
v3 - Kurt Van Dijck
- safe operation for non-candev based devices (vcan, slcan)
based on earlier patch
v4 - Kurt Van Dijck
- trivial patch mistakes fixed
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In net_device notifier calls, it was impossible to determine
if a CAN device is based on candev in a safe way.
This patch adds such test in order to access candev storage
from within those notifiers.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch implements the functions to add two LED triggers, named
<ifname>-tx and <ifname>-rx, to a canbus device driver.
Triggers are called from specific handlers by each CAN device driver and
can be disabled altogether with a Kconfig option.
The implementation keeps the LED on when the interface is UP and blinks
the LED on network activity at a configurable rate.
This only supports can-dev based drivers, as it uses some support field
in the can_priv structure.
Supported drivers should call devm_can_led_init() and can_led_event() as
needed.
Cleanup is handled automatically by devres, so no *_exit function is
needed.
Supported events are:
- CAN_LED_EVENT_OPEN: turn on tx/rx LEDs
- CAN_LED_EVENT_STOP: turn off tx/rx LEDs
- CAN_LED_EVENT_TX: trigger tx LED blink
- CAN_LED_EVENT_RX: trigger tx LED blink
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add device driver for USB2CAN interface from "8 devices" (http://www.8devices.com).
changes since v10:
* small cleanups
changes since v9:
* fixed syslog messages
* fixed crc error number
* increased MAX_RX_URBS and MAX_TX_URBS
changes since v8:
* remove all sysfs files
changes since v7:
* add sysfs documentation
* fix minor styling issue
* fixed can state for passive mode
* changed handling for crc errors
changes since v6:
* changed some variable types to big endian equivalent
* small cleanups
changes since v5:
* unlock mutex on error
changes since v4:
* removed FSF address
* renamed struct usb_8dev
* removed unused variable free_slots
* replaced some _to_cpu functions with pointer equivalent
* fix return value for usb_8dev_set_mode
* handle can errors with separate function
* fix overrun error handling
* rewrite error handling for usb_8dev_start_xmit
* fix urb submit in usb_8dev_start
* various small fixes
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Bernd Krumboeck <krumboeck@universalnet.at>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds an 'if CAN_DEV...endif' Block around the CAN driver
symbols in drivers/net/can/Kconfig. So the 'depends on CAN' dependencies
can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds an 'if CAN...endif' Block around all CAN symbols in
net/can/Kconfig. So the 'depends on CAN' dependencies can be removed.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When posting a message on the bulletin board, the PF calculates crc
over the message and places the result in the message. When the VF
samples the Bulletin Board it copies the message aside and validates
this crc. The length of the message is crucial here and must be the
same in both parties. Since the PF is running in the Hypervisor and
the VF is running in a Vm, they can possibly be of different versions.
As the Bulletin Board is designed to grow forward in future versions,
in the VF the length must not be the size of the message structure
but instead it should be a field in the message itself.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823e1d9 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set.
Fixes compilation by moving function declarations between header files.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In INTA mode, cnic and bnx2x share the same IRQ. During chip reset,
for example, cnic will stop servicing IRQs after it has shutdown the
cnic hardware resources. However, the shared IRQ is still active as
bnx2x needs to finish the reset. There is a window when bnx2x does
not know that cnic is no longer handling IRQ and things don't always
work properly.
Add a flag to tell bnx2x that cnic is handling IRQ. The flag is set
before the first cnic IRQ is expected and cleared when no more cnic
IRQs are expected, so there should be no race conditions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an incorrect SR-IOV memory release which was committed in 1ab4434.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't unload the bnx2x driver if its in a recovery process, or if
the previous load have failed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 15192a8cf there have been a memory leak upon rmmod
of the bnx2x driver.
This corrects the memory leak and corrects the zeroing of internal
memories upon driver load.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing 57712_VF and 57800_VF to CHIP_IS_E2 and CHIP_IS_E3
macros (missing from commit 8395be5).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add/Revise several debug prints in the bnx2x driver - on regular flows
as well as error flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the incorrect usage of `usleep_range(1000, 1000)' into
`usleep_range(1000, 2000)'.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly changes the bnx2x code without `true' functional changes.
Changes include:
1. Gathering macros into a single macro when combination is used multiple
times.
2. Exporting parts of functions into their own functions.
3. Return values after if-else instead of only on the else condition
(where current flow would simply return same value later in the code)
4. Removing some unnecessary code (either dead-code or incorrect conditions)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly corrects white spaces, indentations, and comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reactivate promiscuous mode in H/W upon gfar_init_mac(), if the
net dev requires it (IFF_PROMISC flag set).
This way the promisc mode is preserved accross device reset conditions
like tx timeout, device restore, a.s.o.
Signed-off-by: Voncken C Acksys <cedric.voncken@acksys.fr>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes it is useful to be able to change the MAC address of the
interface for netback devices. For example, when using ebtables it may
be useful to be able to distinguish traffic from different interfaces
without depending on the interface name.
Reported-by: Nikita Borzykh <sample.n@gmail.com>
Reported-by: Paul Harvey <stockingpaul@hotmail.com>
Cc: netdev@vger.kernel.org
Cc: xen-devel@lists.xen.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Matt Wilson <msw@amazon.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last update to the Ethernet HowTo (over 10 years ago) listed this:
------------------------
SEEQ 8005
Status: Obsolete, Driver Name: seeq8005
There is little information about the card included in the driver,
and hence little information to be put here. If you have a question,
you are probably best trying to e-mail the driver author as listed
in the source.
It was marked obsolete as of the 2.4 series kernels.
------------------------
If it was obsolete over a decade ago, the situation can not have
improved with the passage of time, so let us act on that. Even with
today's improved search engines, I was unable to locate any real
meaningful information on the ISA implementation of this rare chip.
There are ARM and SGI variants of the driver in tree, but they do
not depend on the original x86 driver source or header file. We
leave those non-x86 drivers to be deleted by the arch maintainers
when they decide to expire those legacy platforms as a whole.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.
Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:
"...designed to work with all kernels > 1.1.33"
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them. Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is an area I know all too well, after being author of several 8390
drivers, and maintainer of all 8390 drivers during a large part of their
active lifecycle.
To that end, I can say this with a reasonable degree of confidence.
The drivers deleted here represent the earliest (as in early 1990)
hardware and/or rare hardware. The remaining hardware not deleted
here is the more modern/sane of the lot, with ISA-PnP and jumperless
"soft configuration" like the wd and smc cards had.
The original ne2000 driver (ne.c) gets a pass at this time since
AT/LANTIC based cards that could be both ne2000 or wd-like (with
shared memory) and with jumperless configuration were made in the
mid to late 1990's, and performed reasonably well for their era.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another driver for relatively rare 10Mbit hardware that
originated in the early 1990's. So we select it for removal at
this point in time as well.
Cc: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These Fujitsu MB86965 based ISA 10Mbit cards were another of the
relatively rare cards dating from the early 1990s that for one reason
or another didn't seem to get a lot of use in linux. So we retire it
now with a reasonable degree of confidence that it won't impact anyone.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These cards were only available in 8bit format, and in addition
they only had AUI and BNC(10-Base2) interfaces (i.e. no RJ-45).
In fact, they are so rare, that an internet search on these old
cards almost comes up empty, unless the "Micom interlan" name
is used.
This puts them in the equivalent domain as the 3c501, so there
should be no strong opposition to the driver removal, as nobody
is seriously using 3.9+ with 8 bit ISA hardware.
In doing so, the whole "ethernet/racal" category becomes empty,
so we clean up the Makefile/Kconfig and subdir appropriately.
Cc: Andreas Mohr <andi@lisas.de>
Cc: Jan-Pascal van Best <janpascal@vanbest.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Like the other drivers that were in the ISA i825xx family, the ni52
was rather rare, not widely used, and hence perhaps not as reliable
as the more mainstream ISA drivers that were heavily used. Given
that, it is chosen for retirement at this time as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver supported early to mid 1990's Zenith laptops, of the
2" thick variety. The driver was already dead 10+ years ago, but
we see this in the source:
----------------
/* 10/2002
[...]
Tested on a vintage Zenith Z-Note 433Lnp+. Probably broken on
anything else. Testers (and detailed bug reports) are welcome :-).
----------------
To clarify, a 433 translates into a 486 at 33MHz, and a system with
a default of 4MB RAM. I can't fault the noble effort to keep things
working a decade ago, but at this point in time, there is no valid
justification to continue carrying this driver along.
Note that there is no associated Space.c cleanup here since this
driver was using module_init to hook itself in.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These old drivers should not be confused with the very common PCI
cards that are supported by e100.c -- these older 10Mbit ISA only
drivers were not as commonly used as some of the other ISA drivers,
simply due to hardware availability and pricing.
Given the rarity of the hardware, and the subsequent less extensive
use of the drivers, it makes sense to obsolete them at this point
in time, along with other rare/experimental ISA drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For those of us who were around in the early to mid 1990's, we
will remember that the i825xx ethernet support was not something
that was considered sufficiently vetted for 24/7 use.
Folks might be inclined to use *functional* ISA hardware on some
near expired P3 ISA machines for dedicated workhorse applications,
but the odds of using (and relying on) one of these old/experimental
drivers is essentially nil. So lets remove them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parallel port is largely replaced by USB, and even in the
day where these drivers were current, the documented speed was
less than 100kB/s. Let us not pretend that anyone cares about
these drivers anymore, or worse - pretend that anyone is using
them on a modern kernel.
As a side bonus, this is the end of legacy parallel port ethernet,
so we get to drop the whole chunk relating to that in the legacy
Space.c file containing the non-PCI unified probe dispatch.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was amusing that linux was able to make use of this 1980's
technology on machines long past its intended lifespan, but
it probably should go now.
To set some context, the 3c501 was designed in the 1980's to be
used on 8088 PC-XT 8bit ISA machines. It was built using a large
number of discrete TTL components and truly looks like a relic
of the ancient past before large scale integration was common.
But from a functional point of view, the real issue, as stated
in the (also obsolete) Ethernet-HowTo, is that "...the 3c501 can
only do one thing at a time -- while you are removing one packet
from the single-packet buffer it cannot receive another packet,
nor can it receive a packet while loading a transmit packet."
You know things are not good when the Kconfig help text suggests
you make a cron job doing a ping every minute.
Hardware that old and crippled is simply not going to be used by
anyone in a time where 10 year old 100Mbit PCI cards (that are
still functional) are largely give-away items.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver was specific to a "professional workstation" line
of products from around 1993 that used the i82596 ethernet chip
as an on-board ethernet solution.
With a 486 processor, and the premium top of the line model maxing
out at a clock speed of 50MHz, we can safely retire this support.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Apricot was a 486 PC with 4MB RAM, and an on-board ethernet
via an intel i82596 hard-wired to i/o 0x300.
Those who were using linux in the 1990's will recall that the
i82596 driver was not one of the more stable or widely used
drivers of its day. Combine that with the extremely limited
resources of the platform, and it is truly time to expire the
support for this thing.
There are some old m68k targets who were also using this chip,
so rather than poll the m68k user base, we simply cut out the
x86/Apricot support here in this commit.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Delete successive tests to the same location. rc was previously tested and
not subsequently updated. efx_phc_adjtime can return an error code, so the
call is updated so that is tested instead.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we write MAC address to pci config space byte by byte,
this means that we have an intermediate step where mac is wrong.
This patch introduced a new control command to set MAC address,
it's atomic.
VIRTIO_NET_F_CTRL_MAC_ADDR is a new feature bit for compatibility.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to send vq command to set mac address in
virtnet_set_mac_address(), so do this function moving.
Fixed a little issue of coding style.
Signed-off-by: Amos Kong <akong@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the transmit DMA channel field in struct emac_priv
is txchan, not txch.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch calls device_set_wakeup_enable() inside set_wol
callback, so that turning on WOL from user mode utility
can make the 'wakeup' of pegasus device to be enabled, then
remote wakeup may be enabled before putting into sleep.
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant code from build_inline_wqe()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates Copyright year to 2013
v2: Changed Copyright year on Makefile
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the physical function (PF) is reset for any reason the statistics
collection in ixgbevf_update_stats needs to wait to update until after
the reset synchronization ensures that the PF driver is up and running
and is finished with its own reset. Go ahead and clear the link flag to
indicate this when the control message from the PF is received. The
reset synchronization and recovery in the watchdog task will eventually
set the link flag up when the PF has resumed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dev_info to log link up/down messages.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts. The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map. To do this I have expanded the work done in the main loop by
pushing first into tx_buffer. This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor. The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo. By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.
To do this I also needed to change the logic and/or drop some flags. I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do. Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb. Instead we can just check the bitflag in the skb.
In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Kurt Van Dijck