This patch fixes the assumption that output sequence is not contiguous
when input sequence is not contiguous and in-place encryption is done.
Output sequence does not need to be contiguous with associated data.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If dma mapping for dma_addr_out fails, the descriptor memory is freed
but the previous dma mapping for dma_addr_in remains.
This patch resolves the missing dma unmap and groups resource
allocations at function start.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add Advanced Encryption Standard (AES) in Galois/Counter Mode (GCM)
as an IPsec Encapsulating Security Payload (ESP) mechanism
to provide confidentiality and data origin authentication.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add support for AES working in Galois Counter Mode.
There is a limitation related to IV size, similar to the one present in
SW implementation (crypto/gcm.c):
The only IV size allowed is 12 bytes. It will be padded by HW to the right
with 0x0000_0001 (up to 16 bytes - AES block size), according to the GCM
specification.
Signed-off-by: Tudor Ambarus <tudor.ambarus@freescale.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM's memory is broken into following address blocks:
Block Included Registers
0 General Registers
1-4 Job ring registers
6 RTIC registers
7 QI registers
8 DECO and CCB
Size of the above stated blocks varies in various platforms. The block size can be 4K or 64K.
The block size can be dynamically determined by reading CTPR register in CAAM.
This patch initializes the block addresses dynamically based on the value read from this register.
Signed-off-by: Ruchika Gupta <r66431@freescale.com>
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
buf_0 and buf_1 in caam_hash_state are not next to each other.
Accessing buf_1 is incorrect from &buf_0 with an offset of only
size_of(buf_0). The same issue is also with buflen_0 and buflen_1
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The entropy delay (the length in system clocks of each
entropy sample) for the RNG4 block of CAAM is dependent
on the frequency of the SoC. By elaborate methods, it
has been determined that a good starting value for all
platforms integrating the CAAM IP is 3200. Using a
higher value has additional benefit of speeding up
the process of instantiating the RNG, since the entropy
delay will be increased and instantiation of the RNG
state handles will be reattempted by the driver. If the
starting value is low, for certain platforms, this can
lead to a quite lengthy process.
This patch changes the starting value of the length of
the entropy sample to 3200 system clocks.
In addition to this change, the attempted entropy delay
values are now printed on the console upon initialization
of the RNG block.
While here, a safeguard for yielding the processor was
added for ensuring that in very adverse cases,
the CPU isn't hogged by the instantiation loop.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- CTR(AES) optimisation on x86_64 using "by8" AVX.
- arm64 support to ccp
- Intel QAT crypto driver
- Qualcomm crypto engine driver
- x86-64 assembly optimisation for 3DES
- CTR(3DES) speed test
- move FIPS panic from module.c so that it only triggers on crypto
modules
- SP800-90A Deterministic Random Bit Generator (drbg).
- more test vectors for ghash.
- tweak self tests to catch partial block bugs.
- misc fixes.
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (94 commits)
crypto: drbg - fix failure of generating multiple of 2**16 bytes
crypto: ccp - Do not sign extend input data to CCP
crypto: testmgr - add missing spaces to drbg error strings
crypto: atmel-tdes - Switch to managed version of kzalloc
crypto: atmel-sha - Switch to managed version of kzalloc
crypto: testmgr - use chunks smaller than algo block size in chunk tests
crypto: qat - Fixed SKU1 dev issue
crypto: qat - Use hweight for bit counting
crypto: qat - Updated print outputs
crypto: qat - change ae_num to ae_id
crypto: qat - change slice->regions to slice->region
crypto: qat - use min_t macro
crypto: qat - remove unnecessary parentheses
crypto: qat - remove unneeded header
crypto: qat - checkpatch blank lines
crypto: qat - remove unnecessary return codes
crypto: Resolve shadow warnings
crypto: ccp - Remove "select OF" from Kconfig
crypto: caam - fix DECO RSR polling
crypto: qce - Let 'DEV_QCE' depend on both HAS_DMA and HAS_IOMEM
...
RSR (Request Source Register) is not used when
virtualization is disabled, thus don't poll for Valid bit.
Besides this, if used, timeout has to be reinitialized.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
AES currently shares descriptor creation functions with DES and 3DES.
DK bit is set in all cases, however it is valid only for
the AES accelerator.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use dma_mapping_error for every dma_map_single / dma_map_page.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
dma_mapping_error checks for an incorrect DMA address:
s/ctx->sh_desc_enc_dma/ctx->sh_desc_dec_dma
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace dma_set_mask with dma_set_mask_and_coherent, since both
streaming and coherent DMA mappings are being used.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch fixes a memory leak that appears when caam_jr module is unloaded.
Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: Cristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The layer which registers with the crypto API should check for the presence of
the CAAM device it is going to use. If the platform's device tree doesn't have
the required CAAM node, the layer should return an error and not register the
algorithms with crypto API layer.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In the current setup debug file system enables us to debug the operational
details for only one CAAM. This patch adds the support for debugging multiple
CAAM's.
Signed-off-by: Nitesh Narayan Lal <b44382@freescale.com>
Signed-off-by: Vakul Garg <b16394@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
At few places in caamhash and caamalg, after allocating a dmable
buffer for sg table , the buffer was being modified. As per
definition of DMA_FROM_DEVICE ,afer allocation the memory should
be treated as read-only by the driver. This patch shifts the
allocation of dmable buffer for sg table after it is populated
by the driver, making it read-only as per the DMA API's requirement.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM IP has certain 64 bit registers . 32 bit architectures cannot force
atomic-64 operations. This patch adds definition of these atomic-64
operations for little endian platforms. The definitions which existed
previously were for big endian platforms.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For platforms with virtualization enabled
1. The job ring registers can be written to only is the job ring has been
started i.e STARTR bit in JRSTART register is 1
2. For DECO's under direct software control, with virtualization enabled
PL, BMT, ICID and SDID values need to be provided. These are provided by
selecting a Job ring in start mode whose parameters would be used for the
DECO access programming.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Some registers like SECVID, CHAVID, CHA Revision Number,
CTPR were defined as 64 bit resgisters. The IP provides
a DWT bit(Double word Transpose) to transpose the two words when
a double word register is accessed. However setting this bit
would also affect the operation of job descriptors as well as
other registers which are truly double word in nature.
So, for the IP to work correctly on big-endian as well as
little-endian SoC's, change is required to access all 32 bit
registers as 32 bit quantities.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The FIFOST_CONT_MASK define is cut and pasted twice so we can delete the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch moves data allocated using kzalloc to managed data allocated
using devm_kzalloc and cleans now unnecessary kfrees in probe and remove
functions. Also, linux/device.h is added to make sure the devm_*()
routine declarations are unambiguously available. Earlier, in the probe
function ctrlpriv was leaked on the failure of ctrl = of_iomap(nprop, 0);
as well as on the failure of ctrlpriv->jrpdev = kzalloc(...); . These
two bugs have been fixed by the patch.
The following Coccinelle semantic patch was used for making the change:
identifier p, probefn, removefn;
@@
struct platform_driver p = {
.probe = probefn,
.remove = removefn,
};
@prb@
identifier platform.probefn, pdev;
expression e, e1, e2;
@@
probefn(struct platform_device *pdev, ...) {
<+...
- e = kzalloc(e1, e2)
+ e = devm_kzalloc(&pdev->dev, e1, e2)
...
?-kfree(e);
...+>
}
@rem depends on prb@
identifier platform.removefn;
expression e;
@@
removefn(...) {
<...
- kfree(e);
...>
}
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Re-initialize keys_fit_inline to avoid using its stale encrypt() shared
descriptor value prior to building descriptors for the decrypt() and
givencrypt() cases.
Signed-off-by: Vakul Garg <vakul@freescale.com>
[reworded commit text, enhanced code readability]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the checkpatch warnings that the strings were split across
multiple lines. Checkpatch now complains about lines over 80,
but this is better, since we can actually grep the source code
for these strings now.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean up the remnants from the rework. Constify function arguments.
Note that checkpatch again complains about this space before newline,
but this is the original code behavior, so I'm keeping it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This macro is just like an encyclopedia of string handling done wrong.
This must die. This is so wrong on so many levels.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean this function up and rework it into sensible shape. This function
now contains one single dev_err() instead of the previous insanity full
of memory allocation, chaotic string handling and use of SPRINTFCAT().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Clean this function up and rework it into sensible shape. This function
now contains one single dev_err() instead of the previous insanity full
of memory allocation, possible stack overwriting, chaotic string handling
and use of SPRINTFCAT().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Just dissolve this function so it's not in the way of applying
further white magic cleanup down the line.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Fix the functions which can be obviously done right with a simple
dev_err() now. While at it, further press the on-stack allocation
of buffer for sprintf() voodoo down into the abominated functions.
This patch cleans up most of the functions and leaves just two
remaining functions, report_ccb_status() and report_deco_status()
ugly and unhappy.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pass the error type string into the functions, so they can handle
the printing of the string. This is now still using the very unsafe
sprintf(), but we will fix that.
While at this, pass the device pointer too, so we can dev_err()
functions readily when we start fixing this proper.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Implement fast-path error code printout for errors with no associated
handler function. This reduces calls to this kmalloc() nonsense in
SPRINTFCAT() already.
Note that the format of output is compatible with the old code, even
if -- exposed like this -- it looks a bit weird. Checkpatch complains
on this one as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull the error code <-> error string mapping tables out of the function
so the code becomes readable. This lets me see the real flesh of the
functions, without all that flab clouding the view.
Note: There is a checkpatch issue with quoted strings across multiple
lines. I will fix that in a subsequent patch to keep the changes
small and separate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The tentacles of this function were firmly attached to various
places in the CAAM code. Just cut them, or this cthulhu function
will sprout them anew.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case hash key is bigger than algorithm block size, it is hashed.
In this case, memory is allocated to keep this hash in hashed_key.
hashed_key has to be freed on the key_dma dma mapping error path.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
(struct caam_ctx) ctx->key_dma needs to be unmapped
when context is cleaned up.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 61bb86bba1
("crypto: caam - set descriptor sharing type to SERIAL")
changed the descriptor sharing mode from SHARE_WAIT to SHARE_SERIAL.
All descriptor commands that handle the "ok to share" and
"error propagation" settings should also go away, since they have no
meaning for SHARE_SERIAL.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Found by the kbuild test robot, the first argument to caam_init_rng
has a spurious ampersand.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch allocates memory from DMAable region to the caam_rng_ctx object,
earlier it had been statically allocated which resulted in errorneous
behaviour on inserting the caamrng module at the runtime.
Signed-off-by: Nitesh Lal <NiteshNarayanLal@freescale.com>
Acked-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
My guess is that this little endian configuration is never found in real
life, but if it were then the writel() arguments are in the wrong order
so the driver would crash immediately.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC ERA has to be retrieved by reading the "fsl,sec-era" property
from the device tree. This property is updated/filled in by
u-boot.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC Controller driver creates platform devices for it's child job ring nodes.
Currently the driver uses for_each_compatible routine which traverses
the whole device tree to create the job rings for the platform device.
The patch changes this to search for the compatible property of job ring
only in the child nodes i.e., the job rings are created as per the number
of children associated with the crypto node.
Signed-off-by: Nitesh Lal <NiteshNarayanLal@freescale.com>
Reviewed-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Use the common helper function crypto_authenc_extractkeys() for key
parsing.
Also fix the key buffer overflow condition: use split key pad length
instead of authentication key length.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
linuxnext currently doesn't compile with the powerpc mpc85xx_defconfig
giving:
drivers/crypto/caam/jr.c: In function 'caam_jr_probe':
drivers/crypto/caam/jr.c:468:2: error: implicit declaration of function 'of_iomap' [-Werror=implicit-function-declaration]
In:
commit 313ea293e9
Author: Ruchika Gupta <ruchika.gupta@freescale.com>
crypto: caam - Add Platform driver for Job Ring
We added a reference to of_iomap but did add the necessary include file.
The below adds this include.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Acked-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- Made x86 ablk_helper generic for ARM
- Phase out chainiv in favour of eseqiv (affects IPsec)
- Fixed aes-cbc IV corruption on s390
- Added constant-time crypto_memneq which replaces memcmp
- Fixed aes-ctr in omap-aes
- Added OMAP3 ROM RNG support
- Add PRNG support for MSM SoC's
- Add and use Job Ring API in caam
- Misc fixes
[ NOTE! This pull request was sent within the merge window, but Herbert
has some questionable email sending setup that makes him public enemy
#1 as far as gmail is concerned. So most of his emails seem to be
trapped by gmail as spam, resulting in me not seeing them. - Linus ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (49 commits)
crypto: s390 - Fix aes-cbc IV corruption
crypto: omap-aes - Fix CTR mode counter length
crypto: omap-sham - Add missing modalias
padata: make the sequence counter an atomic_t
crypto: caam - Modify the interface layers to use JR API's
crypto: caam - Add API's to allocate/free Job Rings
crypto: caam - Add Platform driver for Job Ring
hwrng: msm - Add PRNG support for MSM SoC's
ARM: DT: msm: Add Qualcomm's PRNG driver binding document
crypto: skcipher - Use eseqiv even on UP machines
crypto: talitos - Simplify key parsing
crypto: picoxcell - Simplify and harden key parsing
crypto: ixp4xx - Simplify and harden key parsing
crypto: authencesn - Simplify key parsing
crypto: authenc - Export key parsing helper function
crypto: mv_cesa: remove deprecated IRQF_DISABLED
hwrng: OMAP3 ROM Random Number Generator support
crypto: sha256_ssse3 - also test for BMI2
crypto: mv_cesa - Remove redundant of_match_ptr
crypto: sahara - Remove redundant of_match_ptr
...
- Earlier interface layers - caamalg, caamhash, caamrng were
directly using the Controller driver private structure to access
the Job ring.
- Changed the above to use alloc/free API's provided by Job Ring Drive
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
With each of the Job Ring available as a platform device, the
Job Ring driver needs to take care of allocation/deallocation
of the Job Rings to the above interface layers. Added APIs
in Job Ring Driver to allocate/free Job rings
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC Job Rings are now available as individual devices.
This would enable sharing of job rings between kernel and
user space. Job Rings can now be dynamically bound/unbound
from kernel.
Changes are made in the following layers of CAAM Driver
1. Controller driver
- Does basic initialization of CAAM Block.
- Creates platform devices for Job Rings.
(Earlier the initialization of Job ring was done
by the controller driver)
2. JobRing Platform driver
- Manages the platform Job Ring devices created
by the controller driver
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: Garg Vakul-B16394 <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Replace some instances of of_irq_map_one()/irq_create_of_mapping() and
of_irq_to_resource() by the simpler equivalent irq_of_parse_and_map().
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
[grant.likely: resolved conflicts with core code renames]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Powerpc is a mess of implicit includes by prom.h. Add the necessary
explicit includes to drivers in preparation of prom.h cleanup.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
KMap the buffers before copying trailing bytes during hmac into a session
temporary buffer. This is required if pinned buffer from user-space is send
during hmac and is safe even if hmac request is generated from within kernel.
Signed-off-by: Yashpal Dutta <yashpal.dutta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG4 block contains multiple (i.e. 2) state handles that can be
initialized. This patch adds the necessary code for detecting
which of the two state handles has been instantiated by another
piece of software e.g. u-boot and instantiate the other one (or
both if none was instantiated). Only the state handle(s)
instantiated by this driver will be deinstantiated when removing
the module.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
RNG4 defines in desc.h were incomplete (bits AI & PS were missing),
while SK was set as an ALG related bit. This patchs adds the
missing bits and corrects the SK bit.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the caam driver module instantiates the RNG state handle 0, then
upon the removal of the module, the RNG state handle is left
initialized. This patch takes care of reverting the state of the
handle back to its previous uninstantatied state.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch splits the RNG4 state handle instantiation
function into two parts: one that handles the creation
of the descriptor which instructs the CAAM to perform
the instantiation of the state handle and another
function that performs the running of the said descriptor
using the DECO debug mechanism.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The RNG4 block in CAAM needs to be 'seeded' first before being used
for generating pseudo-random data. The 'seeding' is done by getting
entropy from the TRNG ring oscillator. The RTFRQMAX register controls
the maximum allowable number of samples that can be aquired during
an entropy sample. Depending on the clock at which the RNG4 block
(and for that matter the SEC block) runs, it's possible that a
hard-coded value for the maximum frequency is inadequate, i.e. more
samples than needed are taken. This is an error, and thus the RNG4
block doesn't get initialized. The patch attempts to alleviate
this issue by trying with progressivly larger frequencies, until
the number of samples is adequate.
This patch also fixes how a descriptor is deemed as being finished:
instead of checking the VALID field in the DECO debug register,
it makes sure that the DECO is idle, by checking the DECO state field
of the said register.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the CAAM driver initialization failed (due to various reasons, e.g. RNG4
initialization failed), then the registration of hash/algorithms/rng shouldn't
take place. This patch adds the necessary code to prevent this registration.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The way the DECO runs a descriptor through the direct (debug)
interface is different from the JRI interface: the DECO will
continue to try and execute the next commands, after the descriptor
buffer has ended. This leads to unpredictable results and possibly
to locking up of the DECO. This patch adds a halt command at the
end of the descriptor to ensure the DECO halts when it reaches
the end of the descriptor buffer.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds an option to the Kconfig file for
SEC which enables the user to see the debug messages
that are printed inside the SEC driver.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CAAM driver contains one macro (xstr) used for printing
the line location in a file where a memdump is done. This patch
replaces the xstr macro with the already existing __stringify
macro that performs the same function.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Remove the dependency of RNG instantiation on Job Ring. Now
RNG instantiation for devices with RNG version > 4 is done
by directly programming DECO 0.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
DESC_JOB_IO_LEN is a generic macro which indicates the space required in
the descriptor for placing SEQIN/OUT commands, job descriptor header,
shared descriptor pointer. Moving it to descriptor construction file
which can be supposedly included by different algo offload files.
Change-Id: Ic8900990d465e9079827b0c7fcacc61766d7efb6
Signed-off-by: Vakul Garg <vakul@freescale.com>
Reviewed-by: Geanta Neag Horia Ioan-B05471 <horia.geanta@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Tested-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add Class Context SRC / DEST flags for the LOAD & STORE commands
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add define for "Adjust Output Frame Length" in order to
set the AOFL bit in the IPsec ESP Decapsulation PDB.
Signed-off-by: Anca-Jeanina Floarea <anca.floarea@freescale.com>
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Store command has options to overwrite the Job Desc, Shared Desc or
the entire Descriptor in memory, using the address from
which the Descriptor was fetched.
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
added all supported math funtion on 8 byte boundary with
immediate flag bit set automatically
added MATH_SRC0_DPOVRD & MATH_SRC1_DPOVRD
The function/defines above are needed for creating descriptors
longer than 64 words
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Perform 32-bit left shift of DEST and concatenate with
left 32 bits of SRC1. {DEST[31:0],SRC1[63:32]}
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Acked-by: Mihai Serb <mihai.serb@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case Store command is used with overwrite Shared Descriptor
feature there is no need for pointer, it is using the
address from which the Shared Descriptor was fetched.
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEQ IN PTR command does not require pointer if RTO or PRE bit is set
Updated desc_constr.h accordingly.
Signed-off-by: Andrei Varvara <andrei.varvara@freescale.com>
Reviewed-by: Phillips Kim-R1AAHA <Kim.Phillips@freescale.com>
Reviewed-by: Fleming Andrew-AFLEMING <AFLEMING@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
req->assoc is dma mapped BIDIRECTIONAL and unmapped TO_DEVICE.
Since it is read-only for the device, use TO_DEVICE both for mapping
and unmapping.
Cc: <stable@vger.kernel.org> # 3.9, 3.8
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
For SEC including a RNG block version >= 4, special initialization
must occur before any descriptor that uses RNG block can be
submitted. This initialization is required not only for SEC
with version greater than 5.0, but for SEC with RNG version >=4.
There may be a case where RNG has already been instantiated by
u-boot or boot ROM code.In such SoCs, if RNG is initialized again
SEC would returns "Instantiation error". Hence, the initialization
status of RNG4 should be also checked before doing RNG init.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Reviewed-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Pull crypto update from Herbert Xu:
- XTS mode optimisation for twofish/cast6/camellia/aes on x86
- AVX2/x86_64 implementation for blowfish/twofish/serpent/camellia
- SSSE3/AVX/AVX2 optimisations for sha256/sha512
- Added driver for SAHARA2 crypto accelerator
- Fix for GMAC when used in non-IPsec secnarios
- Added generic CMAC implementation (including IPsec glue)
- IP update for crypto/atmel
- Support for more than one device in hwrng/timeriomem
- Added Broadcom BCM2835 RNG driver
- Misc fixes
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (59 commits)
crypto: caam - fix job ring cleanup code
crypto: camellia - add AVX2/AES-NI/x86_64 assembler implementation of camellia cipher
crypto: serpent - add AVX2/x86_64 assembler implementation of serpent cipher
crypto: twofish - add AVX2/x86_64 assembler implementation of twofish cipher
crypto: blowfish - add AVX2/x86_64 implementation of blowfish cipher
crypto: tcrypt - add async cipher speed tests for blowfish
crypto: testmgr - extend camellia test-vectors for camellia-aesni/avx2
crypto: aesni_intel - fix Kconfig problem with CRYPTO_GLUE_HELPER_X86
crypto: aesni_intel - add more optimized XTS mode for x86-64
crypto: x86/camellia-aesni-avx - add more optimized XTS code
crypto: cast6-avx: use new optimized XTS code
crypto: x86/twofish-avx - use optimized XTS code
crypto: x86 - add more optimized XTS-mode for serpent-avx
xfrm: add rfc4494 AES-CMAC-96 support
crypto: add CMAC support to CryptoAPI
crypto: testmgr - add empty test vectors for null ciphers
crypto: testmgr - add AES GMAC test vectors
crypto: gcm - fix rfc4543 to handle async crypto correctly
crypto: gcm - make GMAC work when dst and src are different
hwrng: timeriomem - added devicetree hooks
...
checkstack reports report_deco_status(), report_ccb_status() as
particularly excessive stack users. Move their lookup tables
off the stack and put them in .rodata.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
commit 2af8f4a "crypto: caam - coccicheck fixes" added error
return values yet neglected to change the type from unsigned.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This change is required for post SEC-5.0 devices which have RNG4.
Setting RDB in security configuration register allows CAAM to use the
"Random Data Buffer" to be filled by a single request. The Random Data
Buffer is large enough for ten packets to get their IVs from a single
request. If the Random Data Buffer is not enabled, then each IV causes a
separate request, and RNG4 hardware cannot keep up resulting in lower
IPSEC throughput if random IVs are used.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This reverts commit 891104ed00.
Current IPsec ESN implementation for authencesn(cbc(aes), hmac(sha))
(separate encryption and integrity algorithms) does not conform
to RFC4303.
ICV is generated by hashing the sequence
SPI, SeqNum-High, SeqNum-Low, IV, Payload
instead of
SPI, SeqNum-Low, IV, Payload, SeqNum-High.
Cc: <stable@vger.kernel.org> # 3.8, 3.7
Reported-by: Chaoxing Lin <Chaoxing.Lin@ultra-3eti.com>
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The Kconfig entry for CAAM's hash algorithm implementations has always
selected CRYPTO_AHASH. But there's no corresponding Kconfig symbol.
It seems it was intended to select CRYPTO_HASH, like other crypto
drivers do. That would apparently (indirectly) select CRYPTO_HASH2,
which would enable the ahash functionality this driver uses.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: Jamie Iles <jamie@jamieiles.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Alex Porosanu <alexandru.porosanu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull crypto update from Herbert Xu:
- Optimised AES/SHA1 for ARM.
- IPsec ESN support in talitos and caam.
- x86_64/avx implementation of cast5/cast6.
- Add/use multi-algorithm registration helpers where possible.
- Added IBM Power7+ in-Nest support.
- Misc fixes.
Fix up trivial conflicts in crypto/Kconfig due to the sparc64 crypto
config options being added next to the new ARM ones.
[ Side note: cut-and-paste duplicate help texts make those conflicts
harder to read than necessary, thanks to git being smart about
minimizing conflicts and maximizing the common parts... ]
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (71 commits)
crypto: x86/glue_helper - fix storing of new IV in CBC encryption
crypto: cast5/avx - fix storing of new IV in CBC encryption
crypto: tcrypt - add missing tests for camellia and ghash
crypto: testmgr - make test_aead also test 'dst != src' code paths
crypto: testmgr - make test_skcipher also test 'dst != src' code paths
crypto: testmgr - add test vectors for CTR mode IV increasement
crypto: testmgr - add test vectors for partial ctr(cast5) and ctr(cast6)
crypto: testmgr - allow non-multi page and multi page skcipher tests from same test template
crypto: caam - increase TRNG clocks per sample
crypto, tcrypt: remove local_bh_disable/enable() around local_irq_disable/enable()
crypto: tegra-aes - fix error return code
crypto: crypto4xx - fix error return code
crypto: hifn_795x - fix error return code
crypto: ux500 - fix error return code
crypto: caam - fix error IDs for SEC v5.x RNG4
hwrng: mxc-rnga - Access data via structure
hwrng: mxc-rnga - Adapt clocks to new i.mx clock framework
crypto: caam - add IPsec ESN support
crypto: 842 - remove .cra_list initialization
Revert "[CRYPTO] cast6: inline bloat--"
...
we need to configure the TRNG to use more clocks per sample
to handle the two back-to-back 64KiB random descriptor requests
on higher frequency P5040s.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
According to SEC v5.0-v5.3 reference manuals.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support for ESNs (extended sequence numbers).
Tested with strongswan by connecting back-to-back P1010RDB with P2020RDB.
Signed-off-by: Horia Geanta <horia.geanta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
use true/false for bool, fix code alignment, and fix two allocs with
no test.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In 3.6-rc3, without this patch, the following error occurs with a modular build:
ERROR: "gen_split_key" [drivers/crypto/caam/caamhash.ko] undefined!
ERROR: "gen_split_key" [drivers/crypto/caam/caamalg.ko] undefined!
Signed-off-by: Ben Collins <ben.c@servergy.com>
Cc: Yuan Kang <Yuan.Kang@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SHARE_WAIT, whilst more optimal for association-less crypto,
has the ability to start thrashing the CCB descriptor/key
caches, given high levels of traffic across multiple security
associations (and thus keys).
Switch to using the SERIAL sharing type, which prefers
the last used CCB for the SA. On a 2-DECO platform
such as the P3041, this can improve performance by
about 3.7%.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In some device trees of previous version, there were string "fsl,sec4.0".
To be backward compatible with device trees, we first check "fsl,sec-v4.0",
if it fails, then check for "fsl,sec4.0".
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
extended to include new hash and rng code, which was omitted from
the previous version of this patch during a rebase of the SDK
version.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch adds support for retrieving and printing of
SEC ERA information. It is useful for knowing beforehand
what features exist from the SEC point of view on a
certain SoC. Only era-s 1 to 4 are currently supported;
other eras will appear as unknown.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
- rebased onto current cryptodev master
- made caam_eras static
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The caam job rings (input/output job ring) are allocated using
dma_map_single(). These job rings can be visualized as the ring
buffers in which the jobs are en-queued/de-queued. The s/w enqueues
the jobs in input job ring which h/w dequeues and after processing
it copies the jobs in output job ring. Software then de-queues the
job from output ring. Using dma_map/unmap_single() is not preferred
way to allocate memory for this type of requirements because this
adds un-necessary complexity.
Example, if bounce buffer (SWIOTLB) will get used then to make any
change visible in this memory to other processing unit requires
dmap_unmap_single() or dma_sync_single_for_cpu/device(). The
dma_unmap_single() can not be used as this will free the bounce
buffer, this will require changing the job rings on running system
and I seriously doubt that it will be not possible or very complex
to implement. Also using dma_sync_single_for_cpu/device() will also
add unnecessary complexity.
The simple and preferred way is using dma_alloc_coherent() for these
type of memory requirements.
This resolves the Linux boot crash issue when "swiotlb=force" is set
in bootargs on systems which have memory more than 4G.
Signed-off-by: Bharat Bhushan <bharat.bhushan@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
there is no noticeable benefit for multiple cores to process one
job ring's output ring: in fact, we can benefit from cache effects
of having the back-half stay on the core that receives a particular
ring's interrupts, and further relax general contention and the
locking involved with reading outring_used, since tasklets run
atomically.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Memory barriers are implied by the i/o register write implementation
(at least on Power). So we can remove the redundant wmb() in
caam_jr_enqueue, and, in dequeue(), hoist the h/w done notification
write up to before we need to increment the head of the ring, and
save an smp_mb.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Code was needlessly checking the s/w job ring when there
would be nothing to process if the h/w's output completion
ring were empty anyway.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The enqueue lock isn't used in any interrupt context, and
the dequeue lock isn't used in the h/w interrupt context,
only in bh context.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
It has been observed that in zero-loss benchmarks, when a
slow traffic rate is being tested, the IRQ timer coalescing
parameter was set too high, and the ethernet controller
would start dropping packets because the job ring back half
wouldn't be executed in time before the ethernet controller
would fill its buffers, thereby significantly reducing the
zero-loss performance figures.
Empirical testing has shown that the best zero-loss performance
is achieved when IRQ coalescing is set to minimum values and/or
turned off, since apparently the job ring driver already implements
an adequately-performing general-purpose IRQ mitigation strategy
in software.
Whilst we could go with minimal count (2-8) and timing settings
(192-256), we prefer just turning h/w coalescing altogether off
to minimize setkey latency (due to split key generation), and
for consistent cross-SoC performance (the SEC vs. core clock
ratio changes).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC v4.x' RNGB h/w block self-initialized. RNG4, available
on SEC versions 5 and beyond, is based on a different standard
that requires manual initialization.
Also update any new errors From the SEC v5.2 reference manual:
The SEC v5.2's RNG4 unit reuses some error IDs, thus the addition
of rng_err_id_list over the CHA-independent err_id_list.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC v4.x were only 36-bit, SEC v5+ are 40-bit capable.
Also set a DMA mask for any job ring devices created.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam_read copies random bytes from two buffers into output.
caam rng can fill empty buffer 0xffff bytes at a time,
but the buffer sizes are rounded down to multiple of cacheline size.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
support chained scatterlists for aead, ablkcipher and ahash.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
- fix dma unmap leak
- un-unlikely src == dst, due to experience with AF_ALG
Signed-off-by: Kudupudi Ugendreshwar <B38865@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam supports and registers unkeyed sha algorithms and md5.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam supports ahash hmac with sha algorithms and md5.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- rename scatterlist and link_tbl functions
- link_tbl changed to sec4_sg
- sg_to_link_tbl_one changed to dma_to_sec4_sg_one,
since no scatterlist is use
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
create separate files for split key generation and scatterlist functions.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
remove caam_jr_register and caam_jr_deregister
to allow sharing of job rings.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
functions for external storage of seq in/out lengths,
i.e., for 32-bit lengths.
These type-dependent functions automatically determine whether to
store the length internally (embedded in the command header word) or
externally (after the address pointer), based on size of the type
given.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add a PDB header file to support building protocol descriptors.
Signed-off-by: Steve Cornelius <sec@pobox.com>
Signed-off-by: Hemant Agrawal <hemant@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
init_desc, by always ORing with 1 for the descriptor header inclusion
into the descriptor length, and init_sh_desc_pdb, by always specifying
the descriptor length modification for the PDB via options, would not
allow for odd length PDBs to be embedded in the constructed descriptor
length. Fix this by simply changing the OR to an addition.
also round-up pdb_bytes to the next SEC command unit size, to
allow for, e.g., optional packet header bytes that aren't a
multiple of CAAM_CMD_SZ.
Reported-by: Radu-Andrei BULIE <radu.bulie@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Yashpal Dutta <yashpal.dutta@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In case of protocol acceleration descriptors, Shared descriptor header must
carry size of header length + PDB length in words which will be skipped by
DECO while processing descriptor to provide first command word offset
Signed-off-by: Yashpal Dutta <yashpal.dutta@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
SEC4 h/w gets configured in 32- vs. 36-bit physical
addressing modes depending on the size of dma_addr_t,
which is not always equal to sizeof(u32 *).
Also fixed alignment of a dma_unmap call whilst in there.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
presumably leftovers from possible macro development.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In some device trees of previous version, there were string "fsl,sec4.0".
To be backward compatible with device trees, we have CAAM driver first
check "fsl,sec-v4.0", if it fails, then check for "fsl,sec4.0".
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
drivers/crypto/caam/ctrl.c: In function 'caam_probe':
drivers/crypto/caam/ctrl.c:49:6: warning: unused variable 'd' [-Wunused-variable]
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
sha224 and 384 support extends caam noise to 21 lines. Do the same
as commit 5b859b6 "crypto: talitos - be less noisy on startup", but
for caam, and display:
caam ffe300000.crypto: fsl,sec-v4.0 algorithms registered in /proc/crypto
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The added CRYPTO_ALG_KERN_DRIVER_ONLY indicates whether a cipher
is only available via a kernel driver. If the cipher implementation
might be available by using an instruction set or by porting the
kernel code, then it must not be set.
Signed-off-by: Nikos Mavrogiannopoulos <nmav@gnutls.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Access to the SEC4 DECOs (DEscriptor COntrollers) (for debug purposes)
isn't supported or used, and its register access initialization code
erroneously makes illegal i/o accesses that show up as errors when
run under simulation. Remove it until proper support (via DECORR)
is added.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
the polarity of the definition for error propagation was reverse
in the initial desc.h. Fix desc.h and its users.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
manual removal of double-spaces - no non-whitespace changes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
this is the result of running unexpand -a on desc.h.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch converts the drivers in drivers/crypto/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Cc: James Hsiao <jhsiao@amcc.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: take the ACL checks to common code
bury posix_acl_..._masq() variants
kill boilerplates around posix_acl_create_masq()
generic_acl: no need to clone acl just to push it to set_cached_acl()
kill boilerplate around posix_acl_chmod_masq()
reiserfs: cache negative ACLs for v1 stat format
xfs: cache negative ACLs if there is no attribute fork
9p: do no return 0 from ->check_acl without actually checking
vfs: move ACL cache lookup into generic code
CIFS: Fix oops while mounting with prefixpath
xfs: Fix wrong return value of xfs_file_aio_write
fix devtmpfs race
caam: don't pass bogus S_IFCHR to debugfs_create_...()
get rid of create_proc_entry() abuses - proc_mkdir() is there for purpose
asus-wmi: ->is_visible() can't return negative
fix jffs2 ACLs on big-endian with 16bit mode_t
9p: close ACL leaks
ocfs2_init_acl(): fix a leak
VFS : mount lock scalability for internal mounts
caam now supports encrypt and decrypt
for aes, des and 3des
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Job descriptors only contain header and seq pointers.
Other commands are stored in separate shared descriptors
for encrypt, decrypt and givencrypt, stored as arrays
in caam_ctx.
This requires additional macros to create math commands
to calculate assoclen and cryptlen.
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
caam_ctx.key_phys to key_dma
caam_alg_template supports multiple algorithm types
listed in union, which requires cases for
different types in function caam_alg_alloc
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
"aead_authenc" and "ipsec_esp" changed to "aead,"
except for function "ipsec_esp," which is changed
to "init_aead_job."
Variable name of aead_request structures changed
to "req" and name of aead_givcrypt_request structure
changed to "areq"
Signed-off-by: Yuan Kang <Yuan.Kang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
drivers/crypto/caam/ctrl.c: In function 'caam_probe':
drivers/crypto/caam/ctrl.c:55:23: warning: unused variable 'perfmon'
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
setkey allocates 16 bytes (CAAM_CMD_SZ *
DESC_AEAD_SHARED_TEXT_LEN) shy of what is needed to
store the shared descriptor, resulting in memory
corruption. Fix this.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
In doing so, sha512 sized keys would not fit with the current
descriptor inlining mechanism, so we now calculate whether keys
should be referenced instead by pointers in the shared descriptor.
also, use symbols for descriptor text lengths, and, ahem, unmap and
free key i/o memory in cra_exit.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Key sharing is enabled by default in the shared descriptor.
Using CBC decrypt, AES has to alter the key in order to decrypt.
During high traffic decryption rates, i.e, when sharing starts to
take place, we need to use a different OPERATION option to tell AES
that the key was already altered by the PRIOR descriptor - we need
the following kind of logic:
if ( shared )
operation where AES uses decryption key (DK=1)
else
operation where AES uses encryption key (DK=0)
this patch implements this logic using a conditional and
a non-conditional local jump within the decryption job
descriptor.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
this fixes a build error since cryptodev-2.6 got rebased
to include commit d714d1979d
"dt: eliminate of_platform_driver shim code".
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
during recent descriptor development, an Invalid Sequence Command
error triggered a:
BUG: recent printk recursion!
due to insufficient memory allocated for the error text.
The Invalid Sequence Command error text is the longest.
The length of the maximum error string is computed as
the sum of:
"DECO: ": 6
"jump tgt desc idx 255: ": 23
Invalid Sequence Command text: 272
zero termination character: 1
i.e, 302 characters.
Define this maximum error string length in error.h and fix
caam_jr_strstatus callsites.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
keep the hex error value reporting version (a) to be consistent
with decrypt_done(), and (b) to keep our hardware guys happy.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
remains from descriptor debugging - not required for normal operation.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The presence of a h/w Queue Interface would fail due to this
cut-n-paste snafu.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
- add IRQF_SHARED to request_irq flags to support parts such as
the p1023 that has one IRQ line per couple of rings.
- resetting a job ring triggers an interrupt, so move request_irq
prior to jr_reset to avoid 'got IRQ but nobody cared' messages.
- disable IRQs in h/w to avoid contention between reset and
interrupt status
- delete invalid comment - if there were incomplete jobs,
module would be in use, preventing an unload.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Error handling code following a kmalloc should free the allocated data.
The semantic match that finds the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
statement S;
expression E;
identifier f,f1,l;
position p1,p2;
expression *ptr != NULL;
@@
x@p1 = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...x...+> }
(
x->f1 = E
|
(x->f1 == NULL || ...)
|
f(...,x->f1,...)
)
...>
(
return \(0\|<+...x...+>\|ptr\);
|
return@p2 ...;
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
print "* file: %s kmalloc %s return %s" % (p1[0].file,p1[0].line,p2[0].line)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
ARRAY_SIZE() was intended here instead of sizeof(). sizeof() is four
times larger than ARRAY_SIZE(). outstr is normally 256 chars so
printing garbage to it could overfill the buffer and corrupt memory.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
t_alg is an ERR_PTR here so we can't dereference it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Help clarify that the number trailing in compatible nomenclature
is the version number of the device, i.e., change:
"fsl,p4080-sec4.0", "fsl,sec4.0";
to:
"fsl,p4080-sec-v4.0", "fsl,sec-v4.0";
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Steve Cornelius <sec@pobox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of the SEC (talitos).
The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.
This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others. Only AEAD algorithms are implemented
at this time, for use with IPsec.
Many thanks to the Freescale STC team for their contributions
to this driver.
Signed-off-by: Steve Cornelius <sec@pobox.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Tudor Ambarus