The A31 integrated codec has a stereo "Line In" input. Add support for
it to the playback paths.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the DMA engine API documentation, maxburst denotes the
largest possible size of a single transfer, so as not to overflow
destination FIFOs as explained in this excerpt from dmaengine.h
* @src_maxburst: the maximum number of words (note: words, as in
* units of the src_addr_width member, not bytes) that can be sent
* in one burst to the device. Typically something like half the
* FIFO depth on I/O peripherals so you don't overflow it. This
* may or may not be applicable on memory sources.
* @dst_maxburst: same as src_maxburst but for destination target
* mutatis mutandis.
The TX FIFO is 64 samples deep for stereo, and the RX FIFO is 16
samples deep. So maxburst could be 32 and 8 for TX and RX respectively.
Unfortunately the sunxi DMA controller driver takes maxburst as
the requested burst size, rather than a limit, and returns an error
for unsupported values. The original value was 4, but some later
SoCs do not officially support this burst size.
This patch increases maxburst on the TX side to 8, which is supported
by all variants of the sunxi DMA controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with just different register offsets. The analog paths are
very different. There are more inputs and outputs.
The A31s, A23, and H3 have a similar PCM interface, again with register
offsets slightly rearranged. The analog path controls, while very
similar between them and the A31, have been moved a separate bus which
is accessed through a message box like interface in the PRCM address
range. This would be handled by a separate auxiliary device tied in
through the device tree in its supporting create_card function.
The quirks structure is expanded to include different register offsets
and separate callbacks for creating the ASoC card. The regmap_config,
quirks, and of_device_match tables have been moved to facilitate this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This revises existing comments in the register definition macros
section, and adds a few more, so that readers can clearly identify
the types of control registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The audio codec on later Allwinner SoCs have a different layout and
audio path compared to the A10/A20. However the PCM parts are still
the same.
The different layout and audio paths mean we need a different
create_card function for different families, so they can create
DAPM endpoint widgets and routes.
This patch moves the regmap configs, quirks and of_device_id
structures to just before the probe function, so we can, among other
things, include a pointer for the create_card function. None of the
lines of code were changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2s driver was only implementing playback for now. Implement capture to
make sure that's not a limitation anymore.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
While DAPM is mono or single channel, its controls can be shared between
widgets, such as sharing one stereo mixer control between the left and
right channel widgets. An example such as the following routes
[Line In Left]----------<Line In Playback Switch>-------[Left Mixer]
^
^ ^ | ^
(inputs) (paths) <shared stereo mixer control> (outputs)
v v | v
v
[Line In Right]---------<Line In Playback Switch>-------[Right Mixer]
where we have separate widgets and paths for the left and right channels
from "Line In" to "Mixer", but a shared stereo mixer control for the
2 paths.
This patch introduces support for such shared mixer controls, allowing
more than 1 path to be attached to a single stereo control, and being
able to control left/right channels independently.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
To support double channel shared controls split across 2 registers, one
for each channel, we must be able to update both registers together.
Add a second set of register fields to struct snd_soc_dapm_update, and
update the DAPM control writeback (put) callbacks to support this.
For codecs that use custom events which call into DAPM to do updates,
also clear struct snd_soc_dapm_update before using it, so the second
set of fields remains clean.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In the current probe function the GPIO is acquired after the codec's
bus clock is enabled. However if it fails to acquire the GPIO due to
a deferred probe, it does not disable the bus clock before bailing out.
This would result in the clock being enabled multiple times.
Move the code that enables the bus clock after the part that gets the
GPIO, maintaining a separation between resource acquisition and device
enablement in the probe function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
When sun4i_codec_create_card fails, we do not assign a proper error
code to the return value. The return value would be 0 from the previous
function call, or we would have bailed out sooner. This would confuse
the driver core into thinking the device probe succeeded, when in fact
it didn't, leaving various devres based resources lingering.
Make the create_card function pass back a meaningful error code, and
assign it to the return value.
Fixes: 45fb6b6f2a ("ASoC: sunxi: add support for the on-chip codec on
early Allwinner SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just a few trivial small fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CjWZ
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Just a few trivial small fixes"
* tag 'sound-fix-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: line6: fix a crash in line6_hwdep_write()
ALSA: seq: fix passing wrong pointer in function call of compatibility layer
ALSA: hda - Fix a failure of micmute led when having multi adcs
ALSA: line6: Fix POD X3 Live audio input
The error checking here is messed up so we could end up dereferencing
-EFAULT.
Fixes: a16039cbf1 ('ALSA: line6: Add hwdep interface to access the POD control messages')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a fix for Linux 4.9-rc1.
In former commit, a function call of compatibility layer for ALSA sequencer
core was obsoleted by an alternative. Although, the alternative gets a
pointer to kernel stack due to mis-programming. As a result, ALSA sequencer
core unexpectedly refers over kernel stack.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 8ce8eb601c ("ALSA: seq: add an alternative way to handle ioctl requests")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On a Dell laptop, there is no global adcs for all input devices, so
the input devices use the different adc, as a result, dyn_adc_switch
is set to true.
In this situation, it is safe to control the micmute led according to
user's choice of muting/unmuting the current input device, since only
current input device path is active, while other input device paths
are inactive and powered down.
Fixes: 00ef99408b ('ALSA: hda - add mic mute led hook for dell machines')
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A good practice is to prefix the names of functions by the name
of the subsystem.
The kthread worker API is a mix of classic kthreads and workqueues. Each
worker has a dedicated kthread. It runs a generic function that process
queued works. It is implemented as part of the kthread subsystem.
This patch renames the existing kthread worker API to use
the corresponding name from the workqueues API prefixed by
kthread_:
__init_kthread_worker() -> __kthread_init_worker()
init_kthread_worker() -> kthread_init_worker()
init_kthread_work() -> kthread_init_work()
insert_kthread_work() -> kthread_insert_work()
queue_kthread_work() -> kthread_queue_work()
flush_kthread_work() -> kthread_flush_work()
flush_kthread_worker() -> kthread_flush_worker()
Note that the names of DEFINE_KTHREAD_WORK*() macros stay
as they are. It is common that the "DEFINE_" prefix has
precedence over the subsystem names.
Note that INIT() macros and init() functions use different
naming scheme. There is no good solution. There are several
reasons for this solution:
+ "init" in the function names stands for the verb "initialize"
aka "initialize worker". While "INIT" in the macro names
stands for the noun "INITIALIZER" aka "worker initializer".
+ INIT() macros are used only in DEFINE() macros
+ init() functions are used close to the other kthread()
functions. It looks much better if all the functions
use the same scheme.
+ There will be also kthread_destroy_worker() that will
be used close to kthread_cancel_work(). It is related
to the init() function. Again it looks better if all
functions use the same naming scheme.
+ there are several precedents for such init() function
names, e.g. amd_iommu_init_device(), free_area_init_node(),
jump_label_init_type(), regmap_init_mmio_clk(),
+ It is not an argument but it was inconsistent even before.
[arnd@arndb.de: fix linux-next merge conflict]
Link: http://lkml.kernel.org/r/20160908135724.1311726-1-arnd@arndb.de
Link: http://lkml.kernel.org/r/1470754545-17632-3-git-send-email-pmladek@suse.com
Suggested-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Borislav Petkov <bp@suse.de>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit c039aaa77a was incomplete,
missing part of the setup for Live. This makes also audio input work,
in addition to audio output.
Fixes: c039aaa77a
Reported-by: Eddi De Pieri <eddi@depieri.net>
Signed-off-by: Andrej Krutak <dev@andree.sk>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Highlights:
- Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
- Use gas sections for arranging exception vectors et. al.
- Large set of TM cleanups and selftests (Cyril Bur)
- Enable transactional memory (TM) lazily for userspace (Cyril Bur)
- Support for XZ compression in the zImage wrapper (Oliver O'Halloran)
- Add support for bpf constant blinding (Naveen N. Rao)
- Beginnings of upstream support for PA Semi Nemo motherboards (Darren Stevens)
Fixes:
- Ensure .mem(init|exit).text are within _stext/_etext (Michael Ellerman)
- xmon: Don't use ld on 32-bit (Michael Ellerman)
- vdso64: Use double word compare on pointers (Anton Blanchard)
- powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
- powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
- powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K (Aneesh Kumar K.V)
- Fix memory leak in queue_hotplug_event() error path (Andrew Donnellan)
- Replay hypervisor maintenance interrupt first (Nicholas Piggin)
Cleanups & features:
- Sparse fixes/cleanups (Daniel Axtens)
- Preserve CFAR value on SLB miss caused by access to bogus address (Paul Mackerras)
- Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
- Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU) (Simon Guo)
- Optimise syscall entry for virtual, relocatable case (Nicholas Piggin)
- Optimise MSR handling in exception handling (Nicholas Piggin)
- Support for kexec with Radix MMU (Benjamin Herrenschmidt)
- powernv EEH fixes (Russell Currey)
- Suprise PCI hotplug support for powernv (Gavin Shan)
- Endian/sparse fixes for powernv PCI (Gavin Shan)
- Defconfig updates (Anton Blanchard)
- Various performance optimisations (Anton Blanchard)
- Align hot loops of memset() and backwards_memcpy()
- During context switch, check before setting mm_cpumask
- Remove static branch prediction in atomic{, 64}_add_unless
- Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little endian
- Set default CPU type to POWER8 for little endian builds
- KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
- cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
- cxl: replace loop with for_each_child_of_node(), remove unneeded of_node_put() (Andrew Donnellan)
- Fix HV facility unavailable to use correct handler (Nicholas Piggin)
- Remove unnecessary syscall trampoline (Nicholas Piggin)
- fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael Ellerman)
- Quieten EEH message when no adapters are found (Anton Blanchard)
- powernv: Add PHB register dump debugfs handle (Russell Currey)
- Use kprobe blacklist for exception handlers & asm functions (Nicholas Piggin)
- Document the syscall ABI (Nicholas Piggin)
- MAINTAINERS: Update cxl maintainers (Michael Neuling)
- powerpc: Remove all usages of NO_IRQ (Michael Ellerman)
Minor cleanups:
- Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur, Frederic Barrat,
Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng, Simon Guo.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Jnn8
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- Major rework of Book3S 64-bit exception vectors (Nicholas Piggin)
- Use gas sections for arranging exception vectors et. al.
- Large set of TM cleanups and selftests (Cyril Bur)
- Enable transactional memory (TM) lazily for userspace (Cyril Bur)
- Support for XZ compression in the zImage wrapper (Oliver
O'Halloran)
- Add support for bpf constant blinding (Naveen N. Rao)
- Beginnings of upstream support for PA Semi Nemo motherboards
(Darren Stevens)
Fixes:
- Ensure .mem(init|exit).text are within _stext/_etext (Michael
Ellerman)
- xmon: Don't use ld on 32-bit (Michael Ellerman)
- vdso64: Use double word compare on pointers (Anton Blanchard)
- powerpc/nvram: Fix an incorrect partition merge (Pan Xinhui)
- powerpc: Fix usage of _PAGE_RO in hugepage (Christophe Leroy)
- powerpc/mm: Update FORCE_MAX_ZONEORDER range to allow hugetlb w/4K
(Aneesh Kumar K.V)
- Fix memory leak in queue_hotplug_event() error path (Andrew
Donnellan)
- Replay hypervisor maintenance interrupt first (Nicholas Piggin)
Various performance optimisations (Anton Blanchard):
- Align hot loops of memset() and backwards_memcpy()
- During context switch, check before setting mm_cpumask
- Remove static branch prediction in atomic{, 64}_add_unless
- Only disable HAVE_EFFICIENT_UNALIGNED_ACCESS on POWER7 little
endian
- Set default CPU type to POWER8 for little endian builds
Cleanups & features:
- Sparse fixes/cleanups (Daniel Axtens)
- Preserve CFAR value on SLB miss caused by access to bogus address
(Paul Mackerras)
- Radix MMU fixups for POWER9 (Aneesh Kumar K.V)
- Support for setting used_(vsr|vr|spe) in sigreturn path (for CRIU)
(Simon Guo)
- Optimise syscall entry for virtual, relocatable case (Nicholas
Piggin)
- Optimise MSR handling in exception handling (Nicholas Piggin)
- Support for kexec with Radix MMU (Benjamin Herrenschmidt)
- powernv EEH fixes (Russell Currey)
- Suprise PCI hotplug support for powernv (Gavin Shan)
- Endian/sparse fixes for powernv PCI (Gavin Shan)
- Defconfig updates (Anton Blanchard)
- KVM: PPC: Book3S HV: Migrate pinned pages out of CMA (Balbir Singh)
- cxl: Flush PSL cache before resetting the adapter (Frederic Barrat)
- cxl: replace loop with for_each_child_of_node(), remove unneeded
of_node_put() (Andrew Donnellan)
- Fix HV facility unavailable to use correct handler (Nicholas
Piggin)
- Remove unnecessary syscall trampoline (Nicholas Piggin)
- fadump: Fix build break when CONFIG_PROC_VMCORE=n (Michael
Ellerman)
- Quieten EEH message when no adapters are found (Anton Blanchard)
- powernv: Add PHB register dump debugfs handle (Russell Currey)
- Use kprobe blacklist for exception handlers & asm functions
(Nicholas Piggin)
- Document the syscall ABI (Nicholas Piggin)
- MAINTAINERS: Update cxl maintainers (Michael Neuling)
- powerpc: Remove all usages of NO_IRQ (Michael Ellerman)
Minor cleanups:
- Andrew Donnellan, Christophe Leroy, Colin Ian King, Cyril Bur,
Frederic Barrat, Pan Xinhui, PrasannaKumar Muralidharan, Rui Teng,
Simon Guo"
* tag 'powerpc-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (156 commits)
powerpc/bpf: Add support for bpf constant blinding
powerpc/bpf: Implement support for tail calls
powerpc/bpf: Introduce accessors for using the tmp local stack space
powerpc/fadump: Fix build break when CONFIG_PROC_VMCORE=n
powerpc: tm: Enable transactional memory (TM) lazily for userspace
powerpc/tm: Add TM Unavailable Exception
powerpc: Remove do_load_up_transact_{fpu,altivec}
powerpc: tm: Rename transct_(*) to ck(\1)_state
powerpc: tm: Always use fp_state and vr_state to store live registers
selftests/powerpc: Add checks for transactional VSXs in signal contexts
selftests/powerpc: Add checks for transactional VMXs in signal contexts
selftests/powerpc: Add checks for transactional FPUs in signal contexts
selftests/powerpc: Add checks for transactional GPRs in signal contexts
selftests/powerpc: Check that signals always get delivered
selftests/powerpc: Add TM tcheck helpers in C
selftests/powerpc: Allow tests to extend their kill timeout
selftests/powerpc: Introduce GPR asm helper header file
selftests/powerpc: Move VMX stack frame macros to header file
selftests/powerpc: Rework FPU stack placement macros and move to header file
selftests/powerpc: Check for VSX preservation across userspace preemption
...
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX7pEPExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9Du
Fgf+MAOLDX8z7TbxAM4TnpPO7pRYF+wR+AWamVoUnHrq+gdsUkcKbnTlE8PP05Sp
VDf/ugCMcAQoYrrXPPiZLLB6YsJf2eXjlrTeF5eG/oHRC0mBeM/U6nHblNltFPKl
clV5jTm8Rq/I0AHAiYeTDetQsypK3eVjJ0PZLdenVWF+kL/+aTJ4GXIGgH27aSQC
7lwQZBRWfvGyE/IRu2NNXTPMNSaos/JtLh2/Y2qkWVEQ8YYwFxgRkfCRDHbFk2fK
8/mdWWlaBrApZN8t/RlJxo6rxuQGUn01HFvLpRK1N0EMuLWaTUFHQZtUV/KF/JSz
6Gj4tPLvDke0f4N2tIwoF9quXA==
=qgCG
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v4.9
Apart from the cleanups done by Morimoto-san this has very much been a
driver focused release with very little generic change:
- A big factoring out of the simple-card code to allow it to be shared
more with the rcar generic card from Kuninori Morimoto.
- Removal of some operations duplicated on the CODEC level, again by
Kuninori Morimoto.
- Lots more machine support for x86 systems.
- New drivers for Nuvoton NAU88C10, Realtek RT5660 and RT5663.
The recent series of changes to the caching in the SSI driver have
caused a number of problems to appear in some test systems. These are
still not fully understood but we're coming up to the merge window so
for now let's revert commit 7de2763d9b (ASoC: fsl_ssi: Remove
.num_reg_defaults_raw from regmap_config) as backing that out seems to
resolve the problem on affected systems.
Reported-by: Maciej S. Szmigiero" <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently there is a memory leak of module on a ENOMEM return path.
Fix this by kfree'ing module before returning.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds SNDRV_PCM_TRIGGER_SUSPEND/RESUME.
Otherwise, it breaks rsnd driver internal start/stop counter
when suspend/resume. This issue was reported/tested by Hiep
Tested-by: Hiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
TLV_DB_RANGE_HEAD macro was obsoleted by commit bf1d1c9b61 ("ALSA: tlv:
add DECLARE_TLV_DB_RANGE()").
This commit removes usage of the macro, with the obsoleting macro renamed
to SNDRV_CTL_TLVD_DECLARE_DB_RANGE().
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Sparse reports a below warning.
sound/soc/codecs/da7219.c:804:57: warning: dubious: x & !y
The line includes a condition statement; '(a < b) & !c'. Practically, the
evaluated value of this statement equals to the value of '(a < b) && !c'.
Although, it's not an usual way to use bitwise operations as logical
operations to several conditions.
This commit fixes the bug.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark Brown