Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next:
1) Add .release_ops to properly unroll .select_ops, use it from nft_compat.
After this change, we can remove list of extensions too to simplify this
codebase.
2) Update amanda conntrack helper to support v3.4, from Florian Tham.
3) Get rid of the obsolete BUGPRINT macro in ebtables, from
Florian Westphal.
4) Merge IPv4 and IPv6 masquerading infrastructure into one single module.
From Florian Westphal.
5) Patchset to remove nf_nat_l3proto structure to get rid of
indirections, from Florian Westphal.
6) Skip unnecessary conntrack timeout updates in case the value is
still the same, also from Florian Westphal.
7) Remove unnecessary 'fall through' comments in empty switch cases,
from Li RongQing.
8) Fix lookup to fixed size hashtable sets on big endian with 32-bit keys.
9) Incorrect logic to deactivate path of fixed size hashtable sets,
element was being tested to self.
10) Remove nft_hash_key(), the bitmap set is always selected for 16-bit
keys.
11) Use boolean whenever possible in IPVS codebase, from Andrea Claudi.
12) Enter close state in conntrack if RST matches exact sequence number,
from Florian Westphal.
13) Initialize dst_cache in tunnel extension, from wenxu.
14) Pass protocol as u16 to xt_check_match and xt_check_target, from
Li RongQing.
15) SCTP header is granted to be in a linear area from IPVS NAT handler,
from Xin Long.
16) Don't steal packets coming from slave VRF device from the
ip_sabotage_in() path, from David Ahern.
17) Fix unsafe update of basechain stats, from Li RongQing.
18) Make sure CONNTRACK_LOCKS is power of 2 to let compiler optimize
modulo operation as bitwise AND, from Li RongQing.
19) Use device_attribute instead of internal definition in the IDLETIMER
target, from Sami Tolvanen.
20) Merge redir, masq and IPv4/IPv6 NAT chain types, from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-03-02
Here's one more bluetooth-next pull request for the 5.1 kernel:
- Added support for MediaTek MT7663U and MT7668U UART devices
- Cleanups & fixes to the hci_qca driver
- Fixed wakeup pin behavior for QCA6174A controller
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating the multipath hash for input routes the flow info is
not available and therefore should not be used.
Fixes: 24ba14406c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Cc: wenxu <wenxu@ucloud.cn>
Acked-by: wenxu <wenxu@ucloud.cn>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For legacy applications using 32bit variable, SO_MAX_PACING_RATE
has to cap the returned value to 0xFFFFFFFF, meaning that
rates above 34.35 Gbit are capped.
This patch allows applications to read socket pacing rate
at full resolution, if they provide a 64bit variable to store it,
and the kernel is 64bit.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
64bit kernels now support 64bit pacing rates.
This commit changes setsockopt() to accept 64bit
values provided by applications.
Old applications providing 32bit value are still supported,
but limited to the old 34Gbit limitation.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no more in tree users of the
switchdev_trans_item_{dequeue,enqueue} or switchdev_trans_item structure
in the kernel since commit 00fc0c51e3 ("rocker: Change world_ops API
and implementation to be switchdev independant").
Remove this unused code and update the documentation accordingly since.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devlink suffers from a few kdoc warnings:
net/core/devlink.c:5292: warning: Function parameter or member 'dev' not described in 'devlink_register'
net/core/devlink.c:5351: warning: Function parameter or member 'port_index' not described in 'devlink_port_register'
net/core/devlink.c:5753: warning: Function parameter or member 'parent_resource_id' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Function parameter or member 'size_params' not described in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'top_hierarchy' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'reload_required' description in 'devlink_resource_register'
net/core/devlink.c:5753: warning: Excess function parameter 'parent_reosurce_id' description in 'devlink_resource_register'
net/core/devlink.c:6451: warning: Function parameter or member 'region' not described in 'devlink_region_snapshot_create'
net/core/devlink.c:6451: warning: Excess function parameter 'devlink_region' description in 'devlink_region_snapshot_create'
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For ip rules, we need to use 'ipproto ipv6-icmp' to match ICMPv6 headers.
But for ip -6 route, currently we only support tcp, udp and icmp.
Add ICMPv6 support so we can match ipv6-icmp rules for route lookup.
v2: As David Ahern and Sabrina Dubroca suggested, Add an argument to
rtm_getroute_parse_ip_proto() to handle ICMP/ICMPv6 with different family.
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: eacb9384a3 ("ipv6: support sport, dport and ip_proto in RTM_GETROUTE")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge the ipv4 and ipv6 nat chain type. This is the last
missing piece which allows to provide inet family support
for nat in a follow patch.
The kconfig knobs for ipv4/ipv6 nat chain are removed, the
nat chain type will be built unconditionally if NFT_NAT
expression is enabled.
Before:
text data bss dec hex filename
1576 896 0 2472 9a8 nft_chain_nat_ipv4.ko
1697 896 0 2593 a21 nft_chain_nat_ipv6.ko
After:
text data bss dec hex filename
1832 896 0 2728 aa8 nft_chain_nat.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The family specific masq modules are way too small to warrant
an extra module, just place all of them in nft_masq.
before:
text data bss dec hex filename
1001 832 0 1833 729 nft_masq.ko
766 896 0 1662 67e nft_masq_ipv4.ko
764 896 0 1660 67c nft_masq_ipv6.ko
after:
2010 960 0 2970 b9a nft_masq.ko
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
before:
text data bss dec hex filename
990 832 0 1822 71e nft_redir.ko
697 896 0 1593 639 nft_redir_ipv4.ko
713 896 0 1609 649 nft_redir_ipv6.ko
after:
text data bss dec hex filename
1910 960 0 2870 b36 nft_redir.ko
size is reduced, all helpers from nft_redir.ko can be made static.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use struct device_attribute instead of struct idletimer_tg_attr, and
the correct callback function type to avoid indirect call mismatches
with Control Flow Integrity checking.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
CONNTRACK_LOCKS is divisor when computer array index, if it is power of
2, compiler will optimize modulo operation as bitwise AND, or else
modulo will lower performance.
Suggested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Check the result of dereferencing base_chain->stats, instead of result
of this_cpu_ptr with NULL.
base_chain->stats maybe be changed to NULL when a chain is updated and a
new NULL counter can be attached.
And we do not need to check returning of this_cpu_ptr since
base_chain->stats is from percpu allocator if it is non-NULL,
this_cpu_ptr returns a valid value.
And fix two sparse error by replacing rcu_access_pointer and
rcu_dereference with READ_ONCE under rcu_read_lock.
Thanks for Eric's help to finish this patch.
Fixes: 009240940e ("netfilter: nf_tables: don't assume chain stats are set when jumplabel is set")
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Followup to a173f066c7 ("netfilter: bridge: Don't sabotage nf_hook
calls from an l3mdev"). Some packets (e.g., ndisc) do not have the skb
device flipped to the l3mdev (e.g., VRF) device. Update ip_sabotage_in
to not drop packets for slave devices too. Currently, neighbor
solicitation packets for 'dev -> bridge (addr) -> vrf' setups are getting
dropped. This patch enables IPv6 communications for bridges with an
address that are enslaved to a VRF.
Fixes: 73e20b761a ("net: vrf: Add support for PREROUTING rules on vrf device")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
sctp_csum_check() is called by sctp_s/dnat_handler() where it calls
skb_make_writable() to ensure sctphdr to be linearized.
So there's no need to get sctphdr by calling skb_header_pointer()
in sctp_csum_check().
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The proto in struct xt_match and struct xt_target is u16, when
calling xt_check_target/match, their proto argument is u8,
and will cause truncation, it is harmless to ip packet, since
ip proto is u8
if a etable's match/target has proto that is u16, will cause
the check failure.
and convert be16 to short in bridge/netfilter/ebtables.c
Signed-off-by: Zhang Yu <zhangyu31@baidu.com>
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The metadata_dst does not initialize the dst_cache field, this causes
problems to ip_md_tunnel_xmit() since it cannot use this cache, hence,
Triggering a route lookup for every packet.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
TCP resets cause instant transition from established to closed state
provided the reset is in-window. Endpoints that implement RFC 5961
require resets to match the next expected sequence number.
RST segments that are in-window (but that do not match RCV.NXT) are
ignored, and a "challenge ACK" is sent back.
Main problem for conntrack is that its a middlebox, i.e. whereas an end
host might have ACK'd SEQ (and would thus accept an RST with this
sequence number), conntrack might not have seen this ACK (yet).
Therefore we can't simply flag RSTs with non-exact match as invalid.
This updates RST processing as follows:
1. If the connection is in a state other than ESTABLISHED, nothing is
changed, RST is subject to normal in-window check.
2. If the RSTs sequence number either matches exactly RCV.NXT,
connection state moves to CLOSE.
3. The same applies if the RST sequence number aligns with a previous
packet in the same direction.
In all other cases, the connection remains in ESTABLISHED state.
If the normal-in-window check passes, the timeout will be lowered
to that of CLOSE.
If the peer sends a challenge ack, connection timeout will be reset.
If the challenge ACK triggers another RST (RST was valid after all),
this 2nd RST will match expected sequence and conntrack state changes to
CLOSE.
If no challenge ACK is received, the connection will time out after
CLOSE seconds (10 seconds by default), just like without this patch.
Packetdrill test case:
0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
0.000 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
0.000 bind(3, ..., ...) = 0
0.000 listen(3, 1) = 0
0.100 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 7>
0.100 > S. 0:0(0) ack 1 win 64240 <mss 1460,nop,nop,sackOK,nop,wscale 7>
0.200 < . 1:1(0) ack 1 win 257
0.200 accept(3, ..., ...) = 4
// Receive a segment.
0.210 < P. 1:1001(1000) ack 1 win 46
0.210 > . 1:1(0) ack 1001
// Application writes 1000 bytes.
0.250 write(4, ..., 1000) = 1000
0.250 > P. 1:1001(1000) ack 1001
// First reset, old sequence. Conntrack (correctly) considers this
// invalid due to failed window validation (regardless of this patch).
0.260 < R 2:2(0) ack 1001 win 260
// 2nd reset, but too far ahead sequence. Same: correctly handled
// as invalid.
0.270 < R 99990001:99990001(0) ack 1001 win 260
// in-window, but not exact sequence.
// Current Linux kernels might reply with a challenge ack, and do not
// remove connection.
// Without this patch, conntrack state moves to CLOSE.
// With patch, timeout is lowered like CLOSE, but connection stays
// in ESTABLISHED state.
0.280 < R 1010:1010(0) ack 1001 win 260
// Expect challenge ACK
0.281 > . 1001:1001(0) ack 1001 win 501
// With or without this patch, RST will cause connection
// to move to CLOSE (sequence number matches)
// 0.282 < R 1001:1001(0) ack 1001 win 260
// ACK
0.300 < . 1001:1001(0) ack 1001 win 257
// more data could be exchanged here, connection
// is still established
// Client closes the connection.
0.610 < F. 1001:1001(0) ack 1001 win 260
0.650 > . 1001:1001(0) ack 1002
// Close the connection without reading outstanding data
0.700 close(4) = 0
// so one more reset. Will be deemed acceptable with patch as well:
// connection is already closing.
0.701 > R. 1001:1001(0) ack 1002 win 501
// End packetdrill test case.
With patch, this generates following conntrack events:
[NEW] 120 SYN_SENT src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [UNREPLIED]
[UPDATE] 60 SYN_RECV src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80
[UPDATE] 432000 ESTABLISHED src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
[UPDATE] 120 FIN_WAIT src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
[UPDATE] 60 CLOSE_WAIT src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
[UPDATE] 10 CLOSE src=10.0.2.1 dst=10.0.0.1 sport=5437 dport=80 [ASSURED]
Without patch, first RST moves connection to close, whereas socket state
does not change until FIN is received.
[NEW] 120 SYN_SENT src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80 [UNREPLIED]
[UPDATE] 60 SYN_RECV src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80
[UPDATE] 432000 ESTABLISHED src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80 [ASSURED]
[UPDATE] 10 CLOSE src=10.0.2.1 dst=10.0.0.1 sport=5141 dport=80 [ASSURED]
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Change the data type of the following variables from int to bool
across ipvs code:
- found
- loop
- need_full_dest
- need_full_svc
- payload_csum
Also change the following functions to use bool full_entry param
instead of int:
- ip_vs_genl_parse_dest()
- ip_vs_genl_parse_service()
This patch does not change any functionality but makes the source
code slightly easier to read.
Signed-off-by: Andrea Claudi <aclaudi@redhat.com>
Acked-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Without hardware pnetid support there must currently be a pnet
table configured to determine the IB device port to be used for SMC
RDMA traffic. This patch enables a setup without pnet table, if
the used handshake interface belongs already to a RoCE port.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per RFC 8033, it is sufficient for the drop probability
decay factor to have a value of (1 - 1/64) instead of 98%.
This avoids the need to do slow division.
Suggested-by: David Laight <David.Laight@aculab.com>
Signed-off-by: Leslie Monis <lesliemonis@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Documentation/core-api/printk-formats.rst, size_t should be
printed with %zu, rather than %Zu.
In addition, using %Zu triggers a warning on clang (-Wformat-extra-args):
net/sctp/chunk.c:196:25: warning: data argument not used by format string [-Wformat-extra-args]
__func__, asoc, max_data);
~~~~~~~~~~~~~~~~^~~~~~~~~
./include/linux/printk.h:440:49: note: expanded from macro 'pr_warn_ratelimited'
printk_ratelimited(KERN_WARNING pr_fmt(fmt), ##__VA_ARGS__)
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~
./include/linux/printk.h:424:17: note: expanded from macro 'printk_ratelimited'
printk(fmt, ##__VA_ARGS__); \
~~~ ^
Fixes: 5b5e0928f7 ("lib/vsprintf.c: remove %Z support")
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Matthias Maennich <maennich@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It can be reproduced by following steps:
1. virtio_net NIC is configured with gso/tso on
2. configure nginx as http server with an index file bigger than 1M bytes
3. use tc netem to produce duplicate packets and delay:
tc qdisc add dev eth0 root netem delay 100ms 10ms 30% duplicate 90%
4. continually curl the nginx http server to get index file on client
5. BUG_ON is seen quickly
[10258690.371129] kernel BUG at net/core/skbuff.c:4028!
[10258690.371748] invalid opcode: 0000 [#1] SMP PTI
[10258690.372094] CPU: 5 PID: 0 Comm: swapper/5 Tainted: G W 5.0.0-rc6 #2
[10258690.372094] RSP: 0018:ffffa05797b43da0 EFLAGS: 00010202
[10258690.372094] RBP: 00000000000005ea R08: 0000000000000000 R09: 00000000000005ea
[10258690.372094] R10: ffffa0579334d800 R11: 00000000000002c0 R12: 0000000000000002
[10258690.372094] R13: 0000000000000000 R14: ffffa05793122900 R15: ffffa0578f7cb028
[10258690.372094] FS: 0000000000000000(0000) GS:ffffa05797b40000(0000) knlGS:0000000000000000
[10258690.372094] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[10258690.372094] CR2: 00007f1a6dc00868 CR3: 000000001000e000 CR4: 00000000000006e0
[10258690.372094] Call Trace:
[10258690.372094] <IRQ>
[10258690.372094] skb_to_sgvec+0x11/0x40
[10258690.372094] start_xmit+0x38c/0x520 [virtio_net]
[10258690.372094] dev_hard_start_xmit+0x9b/0x200
[10258690.372094] sch_direct_xmit+0xff/0x260
[10258690.372094] __qdisc_run+0x15e/0x4e0
[10258690.372094] net_tx_action+0x137/0x210
[10258690.372094] __do_softirq+0xd6/0x2a9
[10258690.372094] irq_exit+0xde/0xf0
[10258690.372094] smp_apic_timer_interrupt+0x74/0x140
[10258690.372094] apic_timer_interrupt+0xf/0x20
[10258690.372094] </IRQ>
In __skb_to_sgvec(), the skb->len is not equal to the sum of the skb's
linear data size and nonlinear data size, thus BUG_ON triggered.
Because the skb is cloned and a part of nonlinear data is split off.
Duplicate packet is cloned in netem_enqueue() and may be delayed
some time in qdisc. When qdisc len reached the limit and returns
NET_XMIT_DROP, the skb will be retransmit later in write queue.
the skb will be fragmented by tso_fragment(), the limit size
that depends on cwnd and mss decrease, the skb's nonlinear
data will be split off. The length of the skb cloned by netem
will not be updated. When we use virtio_net NIC and invoke skb_to_sgvec(),
the BUG_ON trigger.
To fix it, netem returns NET_XMIT_SUCCESS to upper stack
when it clones a duplicate packet.
Fixes: 35d889d1 ("sch_netem: fix skb leak in netem_enqueue()")
Signed-off-by: Sheng Lan <lansheng@huawei.com>
Reported-by: Qin Ji <jiqin.ji@huawei.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The csum calculation is different for IPv4/6. For VLAN packets,
tc_skb_protocol returns the VLAN protocol rather than the packet's one
(e.g. IPv4/6), so csum is not calculated. Furthermore, VLAN may not be
stripped so csum is not calculated in this case too. Calculate the
csum for those cases.
Fixes: d8b9605d26 ("net: sched: fix skb->protocol use in case of accelerated vlan path")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two array out-of-bounds memory accesses, one in
cipso_v4_map_lvl_valid(), the other in netlbl_bitmap_walk(). Both
errors are embarassingly simple, and the fixes are straightforward.
As a FYI for anyone backporting this patch to kernels prior to v4.8,
you'll want to apply the netlbl_bitmap_walk() patch to
cipso_v4_bitmap_walk() as netlbl_bitmap_walk() doesn't exist before
Linux v4.8.
Reported-by: Jann Horn <jannh@google.com>
Fixes: 446fda4f26 ("[NetLabel]: CIPSOv4 engine")
Fixes: 3faa8f982f ("netlabel: Move bitmap manipulation functions to the NetLabel core.")
Signed-off-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_input_rcu expects the original ingress device (e.g., for
proper multicast handling). The skb->dev can be changed by l3mdev_ip_rcv,
so dev needs to be saved prior to calling it. This was the behavior prior
to the listify changes.
Fixes: 5fa12739a5 ("net: ipv4: listify ip_rcv_finish")
Cc: Edward Cree <ecree@solarflare.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current fib_multipath_hash_policy can make hash based on the L3 or
L4. But it only work on the outer IP. So a specific tunnel always
has the same hash value. But a specific tunnel may contain so many
inner connections.
This patch provide a generic multipath_hash in floi_common. It can
make a user-define hash which can mix with L3 or L4 hash.
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have converted all possible callers to using a switchdev
notifier for attributes we do not have a need for implementing
switchdev_ops anymore, and this can be removed from all drivers the
net_device structure.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drop switchdev_ops.switchdev_port_attr_set. Drop the uses of this field
from all clients, which were migrated to use switchdev notification in
the previous patches.
Add a new function switchdev_port_attr_notify() that sends the switchdev
notifications SWITCHDEV_PORT_ATTR_SET and calls the blocking (process)
notifier chain.
We have one odd case within net/bridge/br_switchdev.c with the
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attribute identifier that
requires executing from atomic context, we deal with that one
specifically.
Drop __switchdev_port_attr_set() and update switchdev_port_attr_set()
likewise.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patches will change the way we communicate setting a port's
attribute and use notifiers towards that goal.
Prepare DSA to support receiving notifier events targeting
SWITCHDEV_PORT_ATTR_SET from both atomic and process context and use a
small helper to translate the event notifier into something that
dsa_slave_port_attr_set() can process.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for allowing switchdev enabled drivers to veto specific
attribute settings from within the context of the caller, introduce a
new switchdev notifier type for port attributes.
Suggested-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 31a9984876 ("net: sched: fw: don't set arg->stop in
fw_walk() when empty")
Cls API function tcf_proto_is_empty() was changed in commit
6676d5e416 ("net: sched: set dedicated tcf_walker flag when tp is empty")
to no longer depend on arg->stop to determine that classifier instance is
empty. Instead, it adds dedicated arg->nonempty field, which makes the fix
in fw classifier no longer necessary.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initialize the .cmd member by using a designated struct
initializer. This fixes warning of missing field initializers,
and makes code a little easier to read.
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
hashtable is never used for 2-byte keys, remove nft_hash_key().
Fixes: e240cd0df4 ("netfilter: nf_tables: place all set backends in one single module")
Reported-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Use the element from the loop iteration, not the same element we want to
deactivate otherwise this branch always evaluates true.
Fixes: 6c03ae210c ("netfilter: nft_set_hash: add non-resizable hashtable implementation")
Reported-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Call jhash_1word() for the 4-bytes key case from the insertion and
deactivation path, otherwise big endian arch set lookups fail.
Fixes: 446a8268b7 ("netfilter: nft_set_hash: add lookup variant for fixed size hashtable")
Reported-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Empty case is fine and does not switch fall-through
Signed-off-by: Li RongQing <lirongqing@baidu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to dirty a cache line if timeout is unchanged.
Also, WARN() is useless here: we crash on 'skb->len' access
if skb is NULL.
Last, ct->timeout is u32, not 'unsigned long' so adapt the
function prototype accordingly.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The l3proto name is gone, its header file is the last trace.
While at it, also remove nf_nat_core.h, its very small and all users
include nf_nat.h too.
before:
text data bss dec hex filename
22948 1612 4136 28696 7018 nf_nat.ko
after removal of l3proto register/unregister functions:
text data bss dec hex filename
22196 1516 4136 27848 6cc8 nf_nat.ko
checkpatch complains about overly long lines, but line breaks
do not make things more readable and the line length gets smaller
here, not larger.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
after ipv4/6 nat tracker merge, there are no external callers, so
make last function static and remove the header.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
before:
text data bss dec hex filename
16566 1576 4136 22278 5706 nf_nat.ko
3598 844 0 4442 115a nf_nat_ipv6.ko
3187 844 0 4031 fbf nf_nat_ipv4.ko
after:
text data bss dec hex filename
22948 1612 4136 28696 7018 nf_nat.ko
... with ipv4/v6 nat now provided directly via nf_nat.ko.
Also changes:
ret = nf_nat_ipv4_fn(priv, skb, state);
if (ret != NF_DROP && ret != NF_STOLEN &&
into
if (ret != NF_ACCEPT)
return ret;
everywhere.
The nat hooks never should return anything other than
ACCEPT or DROP (and the latter only in rare error cases).
The original code uses multi-line ANDing including assignment-in-if:
if (ret != NF_DROP && ret != NF_STOLEN &&
!(IPCB(skb)->flags & IPSKB_XFRM_TRANSFORMED) &&
(ct = nf_ct_get(skb, &ctinfo)) != NULL) {
I removed this while moving, breaking those in separate conditionals
and moving the assignments into extra lines.
checkpatch still generates some warnings:
1. Overly long lines (of moved code).
Breaking them is even more ugly. so I kept this as-is.
2. use of extern function declarations in a .c file.
This is necessary evil, we must call
nf_nat_l3proto_register() from the nat core now.
All l3proto related functions are removed later in this series,
those prototypes are then removed as well.
v2: keep empty nf_nat_ipv6_csum_update stub for CONFIG_IPV6=n case.
v3: remove IS_ENABLED(NF_NAT_IPV4/6) tests, NF_NAT_IPVx toggles
are removed here.
v4: also get rid of the assignments in conditionals.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
David S. Miller