Usually harmless, since the scatterlist is always hard-coded to a length
of 1, but it triggers a BUG() if CONFIG_DEBUG_SG=y, so we better fix it.
This fixes <http://bugzilla.kernel.org/show_bug.cgi?id=9934>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a standard NIC and RDMA/iWARP driver for NetEffect 1/10Gb ethernet adapters.
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the allocation of the MTT or the mailbox failed, mthca_fmr_alloc()
would return 0 (success) no matter what. This leads to crashes a
little down the road, when we try to dereference eg mr->mtt, which was
really ERR_PTR(-Ewhatever).
Signed-off-by: Olaf Kirch <olaf.kirch@oracle.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The string mlx4_ib_version was defined, but never used. Print out the
version once when the first device is initialized.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We have recently discovered that Tavor mode requires each WQE in a
posted list of receive WQEs to have a valid NDA field at all times.
This requirement holds true for regular QPs as well as for SRQs. This
patch prelinks the receive queue in a regular QP and keeps the free
list in SRQ always properly linked.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Reviewed-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SRQ receive posting functions make sure that srq->first_free never
becomes negative, so we can remove tests of whether it is negative.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The firmware QUERY_ADAPTER command does not return vendor_id,
device_id, and revision_id; eliminate these fields from the query.
Initialize the rev_id field of the mlx4 device via init_node_data (MAD
IFC query), as is done in the query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
For memfree devices, the firmware QUERY_ADAPTER command does not
return vendor_id, device_id, and revision_id; do not return these
fields in the QUERY_ADAPTER function for memfree devices.
Instead, for memfree devices, initialize the rev_id field of the mthca
device via init_node_data (MAD IFC query), as is done in the
query_device verb implementation.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In mthca_reg_phys_mr(), we calculate the page size for the HCA
hardware to use to map the buffer list passed in by the consumer.
For example, if the consumer passes in
[0] addr 0x1000, size 0x1000
[1] addr 0x2000, size 0x1000
then the algorithm would come up with a page size of 0x2000 and a list
of two pages, at 0x0000 and 0x2000. Usually, this would work fine
since the memory region would start at an offset of 0x1000 and have a
length of 0x2000.
However, the old code did not take into account the alignment of the
IO virtual address passed in. For example, if the consumer passed in
a virtual address of 0x6000 for the above, then the offset of 0x1000
would not be used correctly because the page mask of 0x1fff would
result in an offset of 0.
We can fix this quite neatly by making sure that the page shift we use
is no bigger than the first bit where the start of the first buffer
and the IO virtual address differ. Also, we can further simplify the
code by removing the special case for a single buffer by noticing that
it doesn't matter if we use a page size that is too big. This allows
the loop to compute the page shift to be replaced with __ffs().
Thanks to Bryan S Rosenburg <rosnbrg@us.ibm.com> for pointing out the
original bug and suggesting several ways to improve this patch.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enables ehca to redirect any PMA queries to the
actual PMA QP.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Reviewed-by: Joachim Fenkes <fenkes@de.ibm.com>
Reviewed-by: Christoph Raisch <raisch@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB spec doesn't allow packets to QP0 sent on any other VL than VL15.
Hardware doesn't filter those packets on the send side, so we need to do
this in the driver and firmware.
As eHCA doesn't support QP0, we can just filter out all traffic going to
QP0, regardless of SL or VL.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.25: (1470 commits)
[IPV6] ADDRLABEL: Fix double free on label deletion.
[PPP]: Sparse warning fixes.
[IPV4] fib_trie: remove unneeded NULL check
[IPV4] fib_trie: More whitespace cleanup.
[NET_SCHED]: Use nla_policy for attribute validation in ematches
[NET_SCHED]: Use nla_policy for attribute validation in actions
[NET_SCHED]: Use nla_policy for attribute validation in classifiers
[NET_SCHED]: Use nla_policy for attribute validation in packet schedulers
[NET_SCHED]: sch_api: introduce constant for rate table size
[NET_SCHED]: Use typeful attribute parsing helpers
[NET_SCHED]: Use typeful attribute construction helpers
[NET_SCHED]: Use NLA_PUT_STRING for string dumping
[NET_SCHED]: Use nla_nest_start/nla_nest_end
[NET_SCHED]: Propagate nla_parse return value
[NET_SCHED]: act_api: use PTR_ERR in tcf_action_init/tcf_action_get
[NET_SCHED]: act_api: use nlmsg_parse
[NET_SCHED]: act_api: fix netlink API conversion bug
[NET_SCHED]: sch_netem: use nla_parse_nested_compat
[NET_SCHED]: sch_atm: fix format string warning
[NETNS]: Add namespace for ICMP replying code.
...
Needed to propagate it down to the __ip_route_output_key.
Signed_off_by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes TOPDIR from infiniband Makefile and delete
one include statement pointing to a non-existing directory
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <mshefty@ichips.intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Correctly work around T3A issues by checking "hwtype != T3A" instead of
"hwtype == T3B". This will be needed for new hardware types.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The existing logic incorrectly maps this buffer list:
0: addr 0x10001000, size 0x1000
1: addr 0x10002000, size 0x1000
To this bogus page list:
0: 0x10000000
1: 0x10002000
The shift calculation must also take into account the address of the
first entry masked by the page_mask as well as the last address+size
rounded up to the next page size.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- for kernel mode cqs, call event notification handler when flushing.
- flush QP when moving from RTS -> CLOSING.
- fix logic to identify a kernel mode qp.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Move the increment of s_hdrwords into the existing if block that tests
if we're doing a send with immediate, to save one test of the opcode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add new mappings from port physical state (a HW register value) to the
IB SubnGet(PortInfo) port physical state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IBA7220 uses a count-based triggering mechanism, and therefore
can't use the same bandwidth verification mechanism as older chips.
To support the 7220, allow enabling and disabling armlaunch errors on
application request. Minor robustness improvements as well.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Clean up some unused header fields, minor related cleanup.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
IBA7220 includes many more configurable IB settings. Getting/setting
these is now grouped into a pair of chip specific functions accessed via
function pointers. Provide sysfs access to these settings.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This adds the new (sometimes empty) chip-specific functions to the older
chips, and makes the initialization and related functions consistent across
all 3 chips.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This code has been unused for some time, but still had leftovers
from when it was used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some HW revisions of eHCA2 may cause an RC connection to break if they
received RDMA Reads over that connection before. This can be
prevented by assuring that, after the first RDMA Read, the QP receives
a new RDMA Read every few million link packets.
Include code into the driver that inserts an empty (size 0) RDMA Read
into the message stream every now and then if the consumer doesn't
post them frequently enough.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch enhances ehca with a capability to "autodetect" the ports
being connected physically. In order to utilize that function the
module option nr_ports must be set to -1 (default is 2 - two
ports). This feature is experimental and will made the default later.
More detail:
If the user connects only one port to the switch, current code requires
1) port one to be connected and
2) module option nr_ports=1 to be given.
If autodetect is enabled, ehca will not wait at creation of the GSI QP
for the respective port to become active. Since firmware does not
accept modify_qp() while the port is down at initialization, we need
to cache all calls to modify_qp() for the SMI/GSI QP and just return a
good return code.
When a port is activated and we get a PORT_ACTIVE event, we replay the
cached modify-qp() parms and re-trigger any posted recv WRs. Only then
do we forward the PORT_ACTIVE event to registered clients.
The result of this autodetect patch is that all ports will be
accessible by the users. Depending on their respective cabling only
those ports that are connected properly will become operable. If a
user tries to modify a regular QP of a non-connected port, modify_qp()
will fail. Furthermore, ibv_devinfo should show the port state
accordingly.
Note that this patch primarily improves the loading behaviour of
ehca. If the cable is removed while the driver is operating and
plugged in again, firmware will handle that properly by sending an
appropriate async event.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There are a few places in the ipath driver where a variable is
re-declared within a block where it is already in scope. Most of these
extra declarations can simply be removed, since the variable from the
outer scope is used in a way so that it does not need to keep its
variable across the block with the re-declaration.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use round_jiffies() to align ehca's 1-second timer with other timers
and potentially save power by sleeping cores for longer.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The original QHT7040 had significant performance issues so there was an
additional check in the driver for a newer serial number. Support for
the small quantities of that board shipped has been dropped, so this
patch removes the special checks to simplify the code.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different chips have different width interrupt status registers, so add
a flag and accessor function to decide which width register read to use.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 6110 had a bug that caused some registers to be swapped; it was
fixed for the 7220 (and didn't affect the 6120 because it had fewer
registers). This adds a flag and related code to handle that, and
includes some minor cleanups in the same area.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
The number of configured ports for the 7220 changes the number of eager
TIDs available per port, for all but port 0 (kernel port) which remains
constant, so add a field to give port0 count separate from the portdata
structure.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
User registers have different alignments on different chips (4KB on
older, 64KB on 7220). Allow mapping the user registers on kernels with
page sizes up to 64K.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Various hardware counters are exported via the ipath file system (since
it is binary data). The old file format was very dependent on the HW
offsets for these registers. Newer HCA chips can have different
counters at different offsets. This patch adds a level of indirection
to make the file format consistent across HCAs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for QLogic HCAs which have hardware performance sampling
registers for PortSamplesControl and PortSamplesResult MADs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch moves some arrays that were defined per-device to be
variables defined in the per context data structure, thus avoiding extra
kzalloc() calls.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for upcoming chips that have different values for
INFINIPATH_R_PORTENABLE_SHIFT, INFINIPATH_R_INTRAVAIL_SHIFT,
INFINIPATH_R_TAILUPD_SHIFT, and portcfg_shift, remove the shared
#defines and use device-specific variables instead.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
kreceive is now portdata * instead of devdata * and other kreceive
related cleanups....
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove an unused parameter and fix up the comment.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a couple of minor problems with RNR NAK handling:
- The insertion sort was causing extra delay when inserting ahead
vs. behind an existing entry on the list.
- A resend of a first packet of a message which is still not ready,
needs another RNR NAK (i.e., it was suppressed when it shouldn't).
- Also, the resend tasklet doesn't need to be woken up unless the
ACK/NAK actually indicates progress has been made.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch allows ehca to forward event client-reregister-required to
registered clients. One such event is generated by a switch eg. after
its reboot.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rather than byte-swapping cqe->g_mlpath_rqpn each time we extract a
field from it, byte-swap it once into a temporary variable. This
results in smaller, better code -- eg, on 32-bit x86:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-5 (-5)
function old new delta
mlx4_ib_poll_cq 1188 1183 -5
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove MSI support from the mthca driver, as scheduled. There is no
reason to use MSI instead of MSI-X, since MSI-X performs better. No
one has spoken up since MSI support was deprecated in commit f6be6fbe
("IB/mthca: Schedule MSI support for removal"), so apparently the MSI
support is unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add the work completion error code to the QP error debug output.
This makes it easier to determine the cause of the error.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An internal code review found the comment here lacking -- update it with
more specifics of how and why the rmb() is there.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During a code review, someone noticed the comments didn't match the code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The gen2_basic tests check for the errno value when a CQ is resized
smaller than the number of outstanding completions queue on the CQ.
This patch changes ib_ipath to return EINVAL which is what ib_mthca
returns and what gen2_basic expects.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Code review pointed out that the locking around uses of ipath_sendctrl
and kr_sendctrl were, in several places, incorrect and/or inconsistent.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one point in time there was code to allow a user process to
wait for a send buffer if none were available. This feature was
never used and most of the code was removed. This removes
some missed unused code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The 5.0 firmware now supports translating sgls in recv work requests,
so remove the host driver logic currently doing the translation.
Note: this change requires 5.0 firmware.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Currently the call into cxgb3 to get the driver info is not serialized.
The iw_cxgb3 module needs to hold the rtnl_lock around the ethtool ops
call like dev_ioctl() does.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Tested-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch is in response to reviewing a patch to the core MAD
processing which fixes loopback of directed route packets to/from user
level MAD agents. This change enables the core code to work for
ib_ipath by fixing the return code from the ipath process_mad method.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Improve interrupt handler cache footprint by noinline'ing error
functions that are rarely called.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 23b9c1ab ("Infiniband: make ipath driver use default driver
groups.") introduced a bug in the ipath driver where
ipath_device_create_group() fell through into the error path, even on
success, which meant that the sysfs groups it created would always get
removed right away. This made ipath_device_remove_group() hit the
BUG_ON() in sysfs_remove_group() when it tried to remove those groups a
second time.
Correct the return path so that the groups stick around until they are
supposed to be cleaned up.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the ipath driver use the new driver functions so that it does not
touch the sysfs portion of the driver structure.
We also remove the redundant symlink from the device back to the driver,
as it is already in the sysfs tree. Any userspace tools should be using
the standard symlink, not some driver specific one.
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Arthur Jones <arthur.jones@qlogic.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a small bug in ipath_ud_rcv()'s handling of UD messages
with immediate data. We need to test whether immediate data is
present and update the header size accordingly *before* testing the
packet size from the header against the actual received length.
Otherwise the wrong header size will be used and all messages with
immediate data will be dropped.
This bug keeps MVAPICH-UD and HP MPI from working at all on ipath devices.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the value of pkey_index in completions to get a valid value for
GSI QPs. Without this fix, incoming GSI packets on port 2 get an
invalid P_Key index in the completion, which prevents the MAD layer
from sending back a response, which can make the second port of
ConnectX HCAs completely useless.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several pSeries firmware versions share a rare locking issue in the
HCA-related hCalls. Check for a feature flag that indicates the issue
being fixed and serialize all HCA hCalls if not.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Firmware would round up the number of SGEs to four, because the WQE
structure holds four SGEs. For SRQ, only three are supported, so return
a fixed value instead.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The formula would yield -1 if the path is faster than the link, which
is wrong in a bad way (max throttling). Clamp to 0, which is the
correct value.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Wrong choice of port number caused modify_qp() to fail -- fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error codes for ib_post_send(), ib_post_recv(), and ib_post_srq_recv()
were inconsistent. Use EINVAL for too many SGEs and ENOMEM for too many
WRs.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_modify_srq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the code which frees the partially allocated QP
resources if there was an error while creating the QP. In particular,
the QPN wasn't deallocated and the QP wasn't removed from the hash
table.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The wrong offset was being returned to libipathverbs so that when
ibv_resize_cq() calls mmap(), it always fails.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The device attribute max_qp_init_rd_atom is not getting set in cxgb3's
query_device method. Version 1.0.4 of librdmacm now validates the
user's requested initiator and responder resources against the max
supported by the device. Since iw_cxgb3 wasn't setting this attribute
(and it defaulted to 0), all rdma_connect()s fail if there are
initiator resources requested by the app. Fix this by setting the
correct value in iwch_query_device().
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPD (inter-packet delay) formula was a little off and assumed a
fixed physical link rate; fix the formula and query the actual
physical link rate, now that we can get it. Also, refactor the
calculation into a common function ehca_calc_ipd() and use that
instead of duplicating code.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Newer firmware versions return physical port information to the
partition, so hand that information to the consumer if it's present.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When an ACK is received, the QP is removed from the timeout list and
then if there are still pending send WQEs, the QP is put back on the
timeout list. It is possible that another post send has put the QP on
the timeout list thus, a check needs to be made before trying to do it
again or the list is corrupted.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Patrick Marchand Latifi <patrick.latifi@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/fmr_pool: Stop ib_fmr threads from contributing to load average
IB/ipath: Fix incorrect use of sizeof on msg buffer (function argument)
IB/ipath: Limit length checksummed in eeprom
IB/ipath: Fix a race where s_last is updated without lock held
IB/mlx4: Lock SQ lock in mlx4_ib_post_send()
IPoIB/cm: Fix receive QP cleanup
Inside a function declared as
void foo(char bar[512])
the value of sizeof bar is the size of a pointer, not 512. So avoid
constructions like this by passing the size explicitly.
Also reduce the size of the buffer to 128 bytes (512 was overly generous).
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The small eeprom that holds the GUID etc. contains a data-length, but if
the actual eeprom is new or has been erased, that byte will be 0xFF,
which is greater than the maximum physical length of the eeprom, and
more importantly greater than the length of the buffer we vmalloc'd.
Sanity-check the length to avoid the possbility of reading past end of
buffer.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a small window where a send work queue entry could be
overwritten by ib_post_send() because s_last is updated before the
entry is read.
This patch closes the window by acquiring the lock and updating
the last send work queue entry index after reading the wr_id.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Because of a typo, mlx4_ib_post_send() takes the same lock rq.lock as
mlx4_ib_post_recv(). Correct the code so the intended sq.lock is
taken when posting a send.
Noticed by Yossi Leybovitch and pointed out by Jack Morgenstein from
Mellanox.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Increase command timeout for INIT_HCA to 10 seconds
IPoIB/cm: Use common CQ for CM send completions
IB/uverbs: Fix checking of userspace object ownership
IB/mlx4: Sanity check userspace send queue sizes
IPoIB: Rewrite "if (!likely(...))" as "if (unlikely(!(...)))"
IB/ehca: Enable large page MRs by default
IB/ehca: Change meaning of hca_cap_mr_pgsize
IB/ehca: Fix ehca_encode_hwpage_size() and alloc_fmr()
IB/ehca: Fix masking error in {,re}reg_phys_mr()
IB/ehca: Supply QP token for SRQ base QPs
IPoIB: Use round_jiffies() for ah_reap_task
RDMA/cma: Fix deadlock destroying listen requests
RDMA/cma: Add locking around QP accesses
IB/mthca: Avoid alignment traps when writing doorbells
mlx4_core: Kill mlx4_write64_raw()
More fallout from sg_page changes:
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf_user1':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1779: error: 'struct scatterlist' has no member named 'page'
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_check_kpages_per_ate':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1835: error: 'struct scatterlist' has no member named 'page'
drivers/infiniband/hw/ehca/ehca_mrmw.c: In function 'ehca_set_pagebuf_user2':
drivers/infiniband/hw/ehca/ehca_mrmw.c:1870: error: 'struct scatterlist' has no member named 'page'
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Found these while looking at printk uses.
Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: Joe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add sanity checks to send queue sizes passed in from userspace. The
minimum sq stride value below is taken from the MT25408 PRM (section
11.10, Table 306, log_sq_stride definition).
Without this check, userspace can submit arbitrarily large/small
values for the number of WQEs and the stride, which can crash the
kernel.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca_shca.hca_cap_mr_pgsize now contains all supported page sizes ORed
together. This makes some checks easier to code and understand, plus
we can return this value verbatim in query_hca(), fixing a problem
with SRP (reported by Anton Blanchard -- thanks!).
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Simplify ehca_encode_hwpage_size(), fixing an infinite loop for pgsize == 0
in the process. Fix the bug in alloc_fmr() that triggered the loop.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Because hardware reports the SRQ token in RWQEs of SRQ base QPs, supply the
base QP token as SRQ token, so we can properly find the SRQ base QP.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Replace struct ibmebus_dev and struct ibmebus_driver with struct of_device
and struct of_platform_driver, respectively. Match the external ibmebus
interface and drivers using it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Architectures such as ia64 see alignment traps when doing a 64-bit
read from __be32 doorbell[2] arrays to do doorbell writes in
mthca_write64(). Fix this by just passing the two halves of the
doorbell value into mthca_write64(). This actually improves the
generated code by allowing the compiler to see what's going on better.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
It's been a useless no-op for long enough in 2.6 so I figured it's time to
remove it. The number of people that could object because they're
maintaining unified 2.4 and 2.6 drivers is probably rather small.
[ Handled drivers added by netdev tree and some missed IRDA cases... -DaveM ]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes most of the generic device layer network
namespace safe. This patch makes dev_base_head a
network namespace variable, and then it picks up
a few associated variables. The functions:
dev_getbyhwaddr
dev_getfirsthwbytype
dev_get_by_flags
dev_get_by_name
__dev_get_by_name
dev_get_by_index
__dev_get_by_index
dev_ioctl
dev_ethtool
dev_load
wireless_process_ioctl
were modified to take a network namespace argument, and
deal with it.
vlan_ioctl_set and brioctl_set were modified so their
hooks will receive a network namespace argument.
So basically anthing in the core of the network stack that was
affected to by the change of dev_base was modified to handle
multiple network namespaces. The rest of the network stack was
simply modified to explicitly use &init_net the initial network
namespace. This can be fixed when those components of the network
stack are modified to handle multiple network namespaces.
For now the ifindex generator is left global.
Fundametally ifindex numbers are per namespace, or else
we will have corner case problems with migration when
we get that far.
At the same time there are assumptions in the network stack
that the ifindex of a network device won't change. Making
the ifindex number global seems a good compromise until
the network stack can cope with ifindex changes when
you change namespaces, and the like.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed to be the same as everywhere else. copy and then zero the page *
in the array first, and then pass the copy to the VM routines.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes some redundant checks when the SMA changes the link
state since the same checks are made in the lower level function that
sets the state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The link state event calls were being generated when the SM told the SMA
to change link states. This works for IB_EVENT_PORT_ACTIVE but not if
the link goes down and stays down. The fix is to generate event calls
from the interrupt handler when the HW link state changes.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The General Purpose I/O pins can be configured to cause interrupts. At
the end of the interrupt code dealing with all known causes, a message
is output if any bits remain un-handled. Since this is a "can't happen"
scenario, it should only be triggered by bugs elsewhere. It is harmless,
and potentially beneficial, to limit the damage by masking any such
unexpected interrupts.
This patch adds disabling of interrupts from any pins that should
not have been allowed to interrupt, in addition to emitting a message.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There is a count of "active hours" maintained in EEPROM, to aid
troubleshooting. The definition of "active" is based on traffic
exceeding a threshold in any given 5-second polling interval. As
originally written, the check was inadvertently bypassed for chips whose
counters were 64-bits wide, and only applied to chips with 32-bit wide
counters.
This patch moves the test for amount of traffic "out" to a more common
location, rather than depending on a side-effect of the software
emulation of 64-bit counts on chips whose hardware is only 32-bits wide.
Signed-off-by: Michael Albaugh <Michael.Albaugh@Qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove all the OEM and bringup boards, and complain and fail
initialization if one is found. QHT7040 with GPIO rework (128ywwuuuu)
is OK, older 112ywwuuuu is no longer supported). The check that had been
added was failing both the 112 and 128 series.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A couple of chip bugs in the iba6110 and in the iba6120 are not in more
recent chips. This first bug swaps two of the pioavail register
locations. In the second bug, the chip can sometimes forget to dma the
pio avail register to memory. We indicate the presence of these bugs
with runtime flags and we indicate the presence of the flags by bumping
the SWMINOR.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
iba6110 rev3 and earlier had a chip bug where the chip could overrun the
recv header queue. rev4 fixed this chip bug so userspace no longer needs
to workaround it. Now we only set the workaround flag for older chip
versions.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ipath_poll() suffered from a couple subtle bugs. Under the right
conditions we could leave recv interrupts enabled on an ipath user
context on close, thereby taking potentially unwanted interrupts on the
next open -- this is fixed by unconditionally turning off recv
interrupts on close. Also, we now use counters rather than set/clear
bits which allows us to make sure we catch all interrupts at the cost of
changing the semantics slightly (it's now give me all events since the
last time I called poll() rather than give me all events since I called
_this_ poll routine). We also added some memory barriers which may help
ensure we get all notifications in a timely manner.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LMC value was being saved by the SMA in two places. This patch
cleans it up so only one copy is kept.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the ability to set the LMC via a sysfs file as if the SM
sent a SubnSet(PortInfo) MAD. It is useful for debugging when no SM is
running.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to add an entry to the completion queue stored the QPN which is
needed for the user level verbs view of the completion queue entry but
the kernel struct ib_wc contains a pointer to the QP instead of a QPN.
When the kernel polled for a completion queue entry, the QPN was lookup
up and the QP pointer recovered. This patch stores the CQE differently
based on whether the CQ is a kernel CQ or a user CQ thus avoiding the
QPN to QP lookup overhead.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch implements the IB_EVENT_QP_LAST_WQE_REACHED event which is
needed by ib_ipoib to destroy the QP when used in connected mode.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Follow the IB spec. (C10-96) for post send which states that a flushed
completion event should be generated for work requests posted when a QP
is in the error state.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes some redundant initialization code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In an earlier change, the amount of data read from the flash was
mistakenly limited to the size known to the current driver. This causes
problems when the length is increased, and written with the new longer
version; the checksum would fail because not enough data was read.
Always read the full 128 byte length to prevent this.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug in the receive processing for UC RDMA WRITE with
immediate which caused the last packet to be dropped.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is a comment change, only, correcting the comment to match the
implemented workaround, rather than the original workaround, and
clarifying why it's needed.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipathfs file system is used to export binary data verses ASCII data
such as through /sys. This patch removes some unneeded files since the
data is available through other /sys files.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There have been a number of issues where host bandwidth via HT or PCIe
to the InfiniPath chip has been limited in some fashion (BIOS,
configuration, etc.), resulting in user confusion. This check gives a
clear warning that something is wrong and needs to be resolved.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to post UD sends tried to process work requests at the time
ib_post_send() is called without using a WQE queue. This was fine as
long as HW resources were available for sending a packet. This patch
changes UD to be handled more like RC and UC and shares more code.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Different processors have different ordering restrictions for write
combining. By taking advantage of this, we can eliminate some write
barriers when writing to the send buffers.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On iba6110 rev4, support for three more IB counters were added. The
LocalLinkIntegrityError counter, the ExcessiveBufferOverrunErrors
counter and support for error counting of flow control packets on an
invalid VL. These counters trigger GPIO interrupts and the sw keeps
track of the counts. Since we also use GPIO interrupts to signal packet
reception, we need to turn off the fast interrupts, or we risk losing a
GPIO interrupt.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Doing min_t(int, foo, INT_MAX) doesn't work correctly, because if foo
is bigger than INT_MAX, then when treated as a signed integer, it will
become negative and hence such an expression is just an elaborate NOP.
Fix such cases in ehca to do min_t(unsigned, foo, INT_MAX) instead.
This fixes negative reported values for max_cqe, max_pd and max_ah:
Before:
max_cqe: -64
max_pd: -1
max_ah: -1
After:
max_cqe: 2147483647
max_pd: 2147483647
max_ah: 2147483647
Based on a bug report and fix from Anton Blanchard <anton@samba.org>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Firmware commands are sent to the HCA by writing multiple words to a
command register block. Access to this block of registers is
serialized with a mutex. However, on large SGI systems, problems were
seen with multiple CPUs issuing FW commands at the same time, because
the writes to the register block may be reordered within the system
interconnect and reach the HCA in a different order than they were
issued (even with the mutex). Fix this by adding an mmiowb() before
dropping the mutex.
Tested-by: Arthur Kepner <akepner@sgi.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Increase the number of QPs allowed per multicast group from 8 to 56.
This allows for one QP per core on 16-core systems, which are now
quite common, and allows some space for future growth.
This is basically the same patch that Jack Morgenstein
<jackm@dev.mellanox.co.il> just supplied for mlx4.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Implement FMRs for mlx4. This is an adaptation of code from mthca.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Write MTT entries directly to ICM from the driver (eliminating use of
WRITE_MTT command). This reduces the number of FW commands needed to
register an MR by at least a factor of 2 and speeds up memory
registration significantly. This code will also be used to implement
FMRs.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
display the following device information under /sys/class/infiniband/mlx4_X:
board_id, fw_ver, hw_rev, hca_type.
This patch makes this information available to userspace utilities
such as ibstat and ibv_devinfo.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* Replace {un}register_cpu_notifier with {un}register_hotcpu_notifier
thereby losing a couple of #ifdef HOTPLUG_CPU pairs.
* Move comp_pool_callback_nb declaration to below that of callback
function so that initialization of .notifier_call and .priority can
occur at build time itself and not runtime.
* Mark the notifier_block (and callback function, and another static
function used by it) as __cpuinit{data} for the sake of consistency
and remove enclosing #ifdef. (This may increase size for modular
build of this module, however, because these are no longer dropped
unconditionally now.)
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Acked-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
...because, on virtualized hardware like System p, we can't be sure
that the physical pages behind them are contiguous otherwise.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We can use raw_smp_processor_id() here because the processor ID is
only used for debug output and therefore our use is preemption-unsafe.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some firmware levels exhibit a race condition between H_ALLOC_RESOURCE(MR)
and H_FREE_RESOURCE(MR). Work around this problem by locking these hvCalls
against each other.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix some modify_qp() issues related to path migration.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change hvcall trace output towards better readability: reg numbers
instead of argument numbers, return code as signed decimal instead of
unsigned hex.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use Paul's new remap_4k_pfn() function to map our 4K firmware contexts
into user space on 64K-page machines without exposing neighboring
firmware contexts. Return the context's offset within a 64K page to
user space so it can determine the proper virtual address.
For details about remap_4k_pfn(), see commit 721151d0 or
http://patchwork.ozlabs.org/linuxppc/patch?id=10281
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
These driver changes incorporate the proposed PCI-X / PCI-Express read
byte count interface. Reading and setting those values doesn't take
place "manually", instead wrapping functions are called to allow
quirks for some PCI bridges.
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At the moment the ehca module parameters are not exported in sysfs.
Export them with 0444 permissions.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca spits out a lot of debugging information. I had to look closely to
see the "Port 1 is not active" message within all the debug:
eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022)
eHCA scaling code enabled
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active.
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_create_qp ehca_define_sqp() failed rc=ffffffffffffffff
ib_mad: Couldn't create ib_mad QP1
ib_mad: Couldn't open ehca0 port 1
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr rc=ffffffffffffffea pd=c000000b4b5b2420 mr_access_flags=7 fmr_attr=c0000005afd37394
fmr_create failed for FMR 0
Remove a few debug statements so that things are clearer:
eHCA Infiniband Device Driver (Rel.: SVNEHCA_0022)
eHCA scaling code enabled
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_define_sqp Port 1 is not active.
ib_mad: Couldn't create ib_mad QP1
ib_mad: Couldn't open ehca0 port 1
ehca D.001.DQDXYCB-P1-C9: PU0006 EHCA_ERR:ehca_alloc_fmr unsupported fmr_attr->page_shift=9
fmr_create failed for FMR 0
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_srq_query() returns a big-endian 16-bit value through an int *,
which screws up sparse checking. Fix this so that a CPU-endian value
is returned.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recover from MSI-X errors by automatically falling back on regular
interrupt, instead of asking the user to do this manually. This makes
it possible to enable MSI-X by default, and will make it possible to
get rid of the msi_x module option in the future.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca_classes.h uses struct mutex, so while <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Acked-by: Stefan Roscher <stefan.roscher@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Use a __set_data_seg() helper in mlx4_ib_post_recv() too; in addition
to making the code easier to read, this also allows gcc to generate
better code -- on x86_64:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
mlx4_ib_post_recv 359 351 -8
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow changing parameter values without having to reload the module.
This is safe because these parameters are only looked at when a new
connection is established.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This is an addendum to commit 0e6e7416 ("IB/mlx4: Handle new FW
requirement for send request prefetching"). We also need to handle
prefetch marking properly for S/G segments, or else the HCA may end up
processing S/G segments that are not fully written and end up sending
the wrong data. This can actually cause data corruption in practice,
especially on systems with relatively slow CPUs (where the HCA is more
likely to prefetch while the CPU is in the middle of writing a work
request into memory).
We write S/G segments in reverse order into the WQE, in order to
guarantee that the first dword of all cachelines containing S/G
segments is written last (overwriting the headroom invalidation
pattern). The entire cacheline will thus contain valid data when the
invalidation pattern is overwritten.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: SRQ fixes to enable IPoIB CM
IB/ehca: Fix Small QP regressions
Fix ehca SRQ support so that IPoIB connected mode works:
- Report max_srq > 0 if SRQ is supported
- Report "last wqe reached" asynchronous event when base QP dies;
this is required by the IB spec and IPoIB CM relies on receiving it
when cleaning up.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new Small QP code had a few bugs that would also make it trigger
for non-Small QPs. Fix them.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.
Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Current code has a cut-and-paste error and returns IB_WC_SEND when it
should return IB_WC_RDMA_READ.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
One patch for two trivial typos of 'error' with three R's, appearing in message strings.
There's a bunch more of the same in comments, not dealt with here.
Signed-off-by: Eddy L O Jansson <eddy@klopper.net>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: Workaround problem of errormask register being overwritten
IB/ipath: Fix some issues with buffer cancel and sendctrl register update
IB/ipath: Use faster put_tid_2 routine after initialization
IB/ipath: Remove unsafe fastrcvint code from interrupt handler
IB/ehca: Move extern declarations from .c files to .h files
IB/mlx4: Whitespace fix
IB/ehca: Fix include order to better match kernel style
mlx4_core: Remove kfree() in mlx4_mr_alloc() error flow
RDMA/amso1100: Initialize the wait_queue_head_t in the c2_qp structure
On some system hardware, we are seeing moderately common cases of the
chip errormask register being overwritten due to a chip bug in iba6120
that is triggered by a vendor-specific PCIe broadcast message. This
patch merely checks periodically, and corrects it if needed (the
overwrite can cause us to not get error and hardware error
interrupts). Also, make dd->ipath_errormask the one, true canonical
source for kr_errormask, and remove references to ipath_ignorederrs as
it is currently unused.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There was confused use of INFINIPATH_S_PIOBUFAVAILUPD (value) and
IPATH_S_PIOBUFAVAILUPD (bit position). Also, some callers of
ipath_cancel_sends() need kr_sendctrl restored, and some want to do it
later.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
At one time the ipath_minrev field was initialized prior to the
ipath_init_iba6120_funcs call, but that is no longer the case, so the
slower put_tid routine was always being used.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The fastrcvint code's purpose was to avoid reading the interrupt
status if kernel packets were in the receive queue (to reduce
overhead). Because intstatus was not read, we could miss the error
interrupt bit indicating freeze mode, since it only delivers a single
interrupt, even if still pending after intclear is written.
This patch removes that unsafe optimization.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make sure declarations stay in sync with definitions by keeping all
extern declarations in common .h files.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Include <rdma/...> headers after <asm/...> headers.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a crash if the driver has to wait for a QP reference to be dropped
when destroying the QP.
Signed-off-by: Ethan Burns <eaburns@iol.unh.edu>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA2 supports QP queues that can be as small as 512 bytes. This
greatly reduces memory overhead for consumers that use lots of QPs
with small queues (e.g. RDMA-only QPs). Apart from dealing with
firmware, this code needs to manage bite-sized chunks of kernel pages,
making sure that no kernel page is shared between different protection
domains.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
They're only used in ehca_qp.c, so make them static to that file.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
ehca2ib_return_code() is not used in any fast path, and making it
non-inline saves ~1.5K of code.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add support for MR pages larger than 4K on eHCA2. This reduces
firmware memory consumption. If enabled via the mr_largepage module
parameter, the MR page size will be determined based on the MR length
and the hardware capabilities -- if the MR is >= 16M, 16M pages are
used, for example.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The error handling code at err_wrid in create_qp_common() does not
handle a userspace QP attached to an SRQ correctly, since it ends up
in the else clause of the if statement. This means it tries to
kfree() the uninitialized qp->sq.wrid and qp->rq.wrid pointers. Fix
this so we only free the wrid arrays for kernel QPs.
Pointed out by Michael S. Tsirkin <mst@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The FW command token is currently only updated on a command completion
event. This means that on command timeout, the same token will be
reused for new command, which results in a mess if the timed out
command *does* eventually complete.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath_layer.[ch] code was an attempt to provide a single interface
for the ipath verbs and ipath_ether code to use. As verbs
functionality increased, the layer's functionality became insufficient
and the verbs code broke away to interface directly to the driver.
The failed attempt to get ipath_ether upstream was the final nail in
the coffin and now it sits quietly in a dark kernel.org corner waiting
for someone to notice the smell and send it along to it's final
resting place. Roland Dreier was that someone -- this patch expands
on his work...
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Temporarily allocated struct mlx4_qp_context *context is leaked by
several error paths. The patch takes advantage of the return value
'err' being preinitialized to -EINVAL.
Spotted by Coverity (CID 1768).
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Transform some calls to kmalloc/memset to a single kzalloc (or kcalloc).
Here is a short excerpt of the semantic patch performing
this transformation:
@@
type T2;
expression x;
identifier f,fld;
expression E;
expression E1,E2;
expression e1,e2,e3,y;
statement S;
@@
x =
- kmalloc
+ kzalloc
(E1,E2)
... when != \(x->fld=E;\|y=f(...,x,...);\|f(...,x,...);\|x=E;\|while(...) S\|for(e1;e2;e3) S\)
- memset((T2)x,0,E1);
@@
expression E1,E2,E3;
@@
- kzalloc(E1 * E2,E3)
+ kcalloc(E1,E2,E3)
[akpm@linux-foundation.org: get kcalloc args the right way around]
Signed-off-by: Yoann Padioleau <padator@wanadoo.fr>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <bryan.wu@analog.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Dave Airlie <airlied@linux.ie>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: Pierre Ossman <drzeus-list@drzeus.cx>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg KH <greg@kroah.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Current code sets size0 to 0 at the start of work request posting
functions and then handles size0 == 0 specially within the loop over
work requests. Change this so size0 is set along with f0 the first
time through the loop (when nreq == 0). This makes the code easier to
understand by making it clearer that f0 and size0 are always
initialized if nreq != 0 without having to know that size0 == 0
implies nreq == 0.
Also annotate size0 with uninitialized_var() so that this doesn't
introduce a new compiler warning.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set UD entries out of the work request posting
functions into inline functions set_tavor_ud_seg() and
set_arbel_ud_seg(). This doesn't change the generated code in any
significant way, and makes the source easier on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set remote address and atomic segment entries out of the
work request posting functions into inline functions set_raddr_seg()
and set_atomic_seg(). This doesn't change the generated code in any
significant way, and makes the source easier on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set remote address, atomic and datagram segments out of
mlx4_ib_post_send() into small helper functions. This doesn't change
the generated code in any significant way, and makes the source easier
on the eyes.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set data segment entries out of mlx4_ib_post_send()
into set_data_seg(). This cleans up the code and lets the compiler do
a better job -- on x86_64:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-16 (-16)
function old new delta
mlx4_ib_post_send 1598 1582 -16
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Factor code to set data segment entries out of the work request
posting functions into inline functions mthca_set_data_seg() and
mthca_set_data_seg_inval(). This makes the code more readable and
also allows the compiler to do a better job -- on x86_64:
add/remove: 0/0 grow/shrink: 0/6 up/down: 0/-69 (-69)
function old new delta
mthca_arbel_post_srq_recv 373 369 -4
mthca_arbel_post_receive 570 562 -8
mthca_tavor_post_srq_recv 520 508 -12
mthca_tavor_post_send 1344 1330 -14
mthca_arbel_post_send 1481 1467 -14
mthca_tavor_post_receive 792 775 -17
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Return the receive queue sizes for both userspace QPs and kernel Qps
(not just kernel QPs) from mlx4_ib_query_qp(). Also zero the send
queue sizes for userspace QPs to avoid a possible information leak,
and set the max_inline_data for kernel QPs to 0 since inline sends are
not supported for kernel QPs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Commit 9db48926 ("drivers/infiniband/hw/mthca/mthca_qp: kill uninit'd
var warning") added "= 0" to the declarations of f0 to shut up gcc
warnings. However, there's no point in making the code bigger by
initializing f0 to a random value just to get rid of a warning;
setting f0 to 0 is no safer than just using uninitialized_var(), which
documents the situation better and gives smaller code too. For example,
on x86_64:
add/remove: 0/0 grow/shrink: 0/2 up/down: 0/-16 (-16)
function old new delta
mthca_tavor_post_send 1352 1344 -8
mthca_arbel_post_send 1489 1481 -8
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make some functions that are only used in a single .c file static. In
addition to being a cleanup, this shrinks the generated code. On x86_64:
add/remove: 1/3 grow/shrink: 2/1 up/down: 4777/-4956 (-179)
function old new delta
handle_errors - 3994 +3994
__verbs_timer 42 710 +668
ipath_do_ruc_send 2131 2246 +115
ipath_no_bufs_available 136 - -136
ipath_disarm_senderrbufs 639 - -639
ipath_ib_timer 658 - -658
ipath_intr 5878 2355 -3523
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When warning about out-of-date firmware, current mthca code messes up
the formatting of the version if the subminor doesn't have three
digits. It doesn't fill the field with 0s so we end up with:
ib_mthca 0000:0b:00.0: HCA FW version 1.1. 0 is old (1.2. 0 is current).
Change the format from "%3d" to "%03d" to get the right thing printed.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The mthca driver supports both MSI and MSI-X. However, MSI-X works with
all hardware that the driver handles, and provides a superset of what
MSI does, so there's no point in having code for both. Schedule MSI
support for removal in 2008 to give anyone who actually needs MSI and
who can't use MSI time to speak up.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Run the existing ehca code through checkpatch.pl and clean up the
worst of the coding style violations.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Split ehca_set_pagebuf() into three functions depending on MR type
(phys/user/fast) and remove superfluous ehca_set_pagebuf_1().
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Rename struct ehca_mr fields to clearly distinguish between kernel
and HW page size.
- Sort struct ehca_mr_pginfo into a common part and a union containing
specific fields for physical, user and fast MR
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Instead of one error mapping function for each potential error source
in ehca_mrmw.c, use a centralized function that handles all cases,
saving a three-figure line count.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Autodetection was missing a few HW revisions, causing certain eHCA1
revisions to be treated like eHCA2. Fixed.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When clearing the ib_ah_attr parameter in to_ib_ah_attr(), use sizeof
*ib_ah_attr instead of sizeof *path. This is the same bug as was
fixed for mthca in 99d4f22e ("IB/mthca: Use correct structure size in
call to memset()"), but the code was cut and pasted into mlx4 before the
fix was merged.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When a QP is in the INIT state, the sched_queue field hasn't been given
to the firmware yet, so the firmware cannot return the value when the QP
is queried. To handle this, use the port number that is saved in the
driver's QP data structure.
Found by Dotan Barak and Yaron Gepstein of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Correct the mask used to get the flow label, since the field is 20 bits,
not 24 bits.
Found by Dotan Barak and Yaron Gepstein of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
drivers/infiniband/hw/mthca/mthca_qp.c: In function
‘mthca_tavor_post_send’:
drivers/infiniband/hw/mthca/mthca_qp.c:1594: warning: ‘f0’ may be used
uninitialized in this function
drivers/infiniband/hw/mthca/mthca_qp.c: In function
‘mthca_arbel_post_send’:
drivers/infiniband/hw/mthca/mthca_qp.c:1949: warning: ‘f0’ may be used
uninitialized in this function
Initializing 'f0' is not strictly necessary in either case, AFAICS.
I was considering use of uninitialized_var(), but looking at the
complex flow of control in each function, I feel it is wiser and
safer to simply zero the var and be certain of ourselves.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (76 commits)
IB: Update MAINTAINERS with Hal's new email address
IB/mlx4: Implement query SRQ
IB/mlx4: Implement query QP
IB/cm: Send no match if a SIDR REQ does not match a listen
IB/cm: Fix handling of duplicate SIDR REQs
IB/cm: cm_msgs.h should include ib_cm.h
IB/cm: Include HCA ACK delay in local ACK timeout
IB/cm: Use spin_lock_irq() instead of spin_lock_irqsave() when possible
IB/sa: Make sure SA queries use default P_Key
IPoIB: Recycle loopback skbs instead of freeing and reallocating
IB/mthca: Replace memset(<addr>, 0, PAGE_SIZE) with clear_page(<addr>)
IPoIB/cm: Fix warning if IPV6 is not enabled
IB/core: Take sizeof the correct pointer when calling kmalloc()
IB/ehca: Improve latency by unlocking after triggering the hardware
IB/ehca: Notify consumers of LID/PKEY/SM changes after nondisruptive events
IB/ehca: Return QP pointer in poll_cq()
IB/ehca: Change idr spinlocks into rwlocks
IB/ehca: Refactor sync between completions and destroy_cq using atomic_t
IB/ehca: Lock renaming, static initializers
IB/ehca: Report RDMA atomic attributes in query_qp()
...
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kick the hardware before unlocking the send/receive queue to overlap
processing a little more.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When firmware reports a nondisruptive port configuration change event,
previous versions of the eHCA driver didn't forward the event to consumers
like IPoIB. Add code that determines the type of configuration change by
comparing old and new port attributes and reports it.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This eliminates lock contention among IRQs as well as the need to
disable IRQs around idr_find, because there are no IRQ writers.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- ehca_cq.nr_events is made an atomic_t, eliminating a lot of locking.
- The CQ is removed from the CQ idr first now to make sure no more
completions are scheduled on that CQ. The "wait for all completions to
end" code becomes much simpler this way.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Rename all spinlock flags to "flags", matching the vast majority of kernel
code.
- Move hcall_lock into the only file it's used in.
- Replaced spin_lock_init() and friends with static initializers for
global variables.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Support SRQs on eHCA2. Since an SRQ is a QP for eHCA2, a lot of code
(structures, create, destroy, post_recv) can be shared between QP and SRQ.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Replace init_qp_queues() by a shorter init_qp_queue(), eliminating
duplicate code.
- hipz_h_alloc_resource_qp() doesn't need a pointer to struct ehca_qp any
longer. All input and output data is transferred through the parms
parameter.
- Change the interface to also support SRQ.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In preparation for support of new eHCA2 features, change adapter probing:
- Hardware level is changed to encode major and minor chip version
- Hardware capabilities are queried from the firmware
- The maximum MTU is queried from the firmware instead of assuming a
fixed value
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Return the PortGUID of the correct port when responding to a NodeInfo
query. Returning the SystemImageGUID causes issues when there are
multiple HCAs in a single system.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The changeset 3859e39d ("IB/ipath: Support larger IB_QP_MAX_DEST_RD_ATOMIC
and IB_QP_MAX_QP_RD_ATOMIC") added support for larger RD_ATOMIC values,
but it failed to take out the stricter checks that were before these and
hence had no effect. This patch takes out the bogus checks....
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
All too often, interrupts do not get enabled for our card due to BIOS
misconfiguration and other issues. This patch checks for that
condition on startup and warns the user. This patch is based on work
(check LID availability) by Robert Walsh.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The default calculation for the number of send buffers to allocate to
the kernel was too high for the PCIe version of the chip thus leaving
fewer than desired send buffers for user MPI applications.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We are more careful to be sure that we don't lose information about
changes that occurred while we were in freeze mode, when the chip will
not notify us, and try to avoid false error interrupts while doing
cleanup. Put all of this logic in a new function ipath_clear_freeze().
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a barrier to make sure the CPU doesn't reorder writes to memory,
since user programs can be polling on the head index update and the
entry should be written before that.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
[ Also remove cast from void * return of kmalloc() as suggested by
Jesper Juhl <jesper.juhl@gmail.com>. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This bug results in an abort request being sent down _after_ the tid
has been released. If the tid happens to have been reused, then the
subsequent generation of the tid gets incorrectly aborted.
The thread running iwch_accecpt_cr() must not abort a connection if an
error is returned after being awakened. If any errors did occur while
iwch_accept_cr() is blocked, then the connection has already been
aborted on the thread processing the error.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The LLD does this for us in cxgb3_remove_tid().
Also fixed active open failure cases where we also shouldn't be
releasing the TID.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Negative advice messages should _not_ count toward the 2 abort
requests needed to indicate an abort request.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Don't set the gen bits nor length bits in the terminate WR. This is
done by the LLD driver.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a HW issue, our current scheme to transition the connection from
streaming to rdma mode is broken on the passive side. The firmware
and driver now support a new transition scheme for the passive side:
- driver posts rdma_init_wr (now including the initial receive seqno)
- driver posts last streaming message via TX_DATA message (MPA start
response)
- uP atomically sends the last streaming message and transitions the
tcb to rdma mode.
- driver waits for wr_ack indicating the last streaming message was ACKed.
NOTE: This change also bumps the required firmware version to 4.3.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Get the maximum message size from the device capabilities returned
from the QUERY_DEV_CAP firmware command, rather than hard-coding 2 GB.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Now that it's June, it's about time to update
the copyright notices of files that have changed.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix ipath_poll and enhance it so we can poll for urgent packets or
regular packets and receive notifications of when a header queue
overflows.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB specification ch. 9.9.3 table 58 says that a QP which isn't set
up for the operation should return a NAK invalid request.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During compliance testing and when debugging some interconnect issues,
it is very useful to be able to send malformed packets, without having
the device signal them as malformed (drop, or terminate with EBP). The
hardware supports this, but the driver "diagnostic packet" interface
did not.
Extend capability to send specific malformed packets for testing.
Signed-off-by: Michael Albaugh <Michael.Albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Previously the driver and userspace code handled the case of 1 subport
somewhat inconsistently. The new interpretation of this situation is
that if one subport is requested, the driver turns on the subport
mechanism and arranges for the port to be "shared" by one process. In
normal use the userspace library does not use this configuration and
instead arranges for the port not to be shared at all. This
particular idiom can be useful for testing purposes.
Signed-off-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When subports are required to run a program, this patch checks that
the driver and the userspace library have compatible subport
implementations. This is achieved through checks on the swminor
version field built into the driver and userspace library. Bad
combinations are reported through syslog and result in an error when
opening the port.
Signed-off-by: Mark Debbage <mark.debbage@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A duplicate RDMA read request can fool the responder into NAKing a new
RDMA read request because the responder wasn't keeping track of
whether the queue of RDMA read requests had been sent at least once.
For example, requester sends 4 2K byte RDMA read requests, times out,
and resends the first, then sees the 4 responses, then sends a 5th
RDMA read or atomic operation. The responder sees the 4 requests,
sends 4 responses, sees the resent 1st request, rewinds the queue,
then sees the 5th request but thinks the queue is full and that the
requester is invalidly sending a 5th new request.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code to copy data from the receive queue buffers to the IB SGEs
doesn't check the SGE length, only the memory region/page length when
copying data. This could overwrite parts of the user's memory that
were not intended to be written. It can only happen if multiple SGEs
are used to describe a receive buffer which almost never happens in
practice.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The send function is called when posting new send work requests.
There is no point in trying to send a packet if the QP is already
waiting for a HW send buffer so don't clear the busy bit until the
buffer available interrupt happens.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A RDMA read response or atomic response can ACK earlier sends and RDMA
writes. In this case, the wrong work request pointer was being used
to store the read first response or atomic result. Also, if a RDMA
read request is retried, the code to compute which request to resend
was incorrect.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This centralizes the use of the abort functionality, removes the
unneeded buffer cancel (abort does the same thing), sets up to ignore
launch errors after abort, same as cancel. We need abort on exit from
freeze mode to avoid having buffers stuck in the busy state, if a user
process happened to complete the send while we were in freeze mode
doing the recovery.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The values passed have never been right for iba 6120 chips, but just
happened to work. We needed to select the right buffer offset in the
chip (both are in same register), and the total length was wrong also,
but was covered by the rounding up.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define pkt rcvd 'type' in a way consistent with HW spec and chips.
The hardware considers received packets of type 0 to be expected, and
type 1 to be eager. The driver was calling the ipath_f_put_tid
functions using a variable called 'type' set to 0 for eager and to 1
for expected packets. Worse, the iba6110 and iba6120 drivers used
those values inconsistently. This was quite confusing. Now
everything is consistent with the hardware.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to chapter 17.2.8.1.1, QPs start in the migrated state and
should send packets with the M bit set in the BTH.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a minor bug where the wrong QP was checked for a send
work request that should wait for an RNR timeout.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes a bug introduced when moving some code around for
readability.
Setting the wqe pointer at the end of the function is a NOP since it
isn't used. Move it back to where it is used.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
In ipath_query_device(), some of the struct ib_device_attr fields were
not being initialized.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Although our chip supports 4K MTUs, our driver doesn't yet support
this feature, so limit the maximum MTU to 2K until we get support for
4K MTUs implemented.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recognize IBA 6110 Revision 4: same feature set, etc. as earlier revisions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We currently track various errors, now we enhance that capability by
logging some of them to EEPROM. We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IPATH_RUNTIME_PBC_REWRITE and the IPATH_RUNTIME_LOOSE_DMA_ALIGN
flags were not ever implemented correctly and did not turn out to be
necessary. Remove the last vestiges of these flags but mark the spot
with a comment to remind us to not reuse these flags in the interest
of binary compatibility. The INFINIPATH_XGXS_SUPPRESS_ARMLAUNCH_ERR
bit was also not found to be useful, so it was dropped in the cleanup
as well.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new LED blinking interface adds more contention for the
unprotected GPIO pins that were already shared, though not commonly at
the same time. We add locks to the accesses to these pins so that
Read-Modify-Write is now safe. Some of these locks are added at
interrupt context, so we shadow the registers which drive and inspect
these pins to avoid the mmio read/writes. This mitigates the effects
of the locks and hastens us through the interrupt.
Add locking and always use shadows for registers controlling GPIO pins
(ExtCtrl and GPIOout). The use of shadows implies doing less I/O,
which can make I2C operation too fast on some platforms. An explicit
udelay(1) in SCL manipulation fixes that.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.
A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mlx4_ib.h uses struct mutex, so although <linux/mutex.h> seems to be
pulled in indirectly by one of the headers it includes, the right
thing is to include <linux/mutex.h> directly.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Refactor the ehca changes from commit ed23a727 ("IB: Return "maybe
missed event" hint from ib_req_notify_cq()") so the queue arithmetic
is done in slightly fewer lines. Also, move the spinlock flags into
the block they're used in.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to keep a spare entry in the SRQ so that there always is a
next WQE available when posting receives (so that we can tell the
difference between a full queue and an empty queue). So subtract 1
from the value HW gives us before reporting the limit on SRQ entries
to consumers.
Found by Mellanox QA.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Inline data segments in send WQEs are not allowed to cross a 64 byte
boundary. We use inline data segments to hold the UD headers for MLX
QPs (QP0 and QP1). A send with GRH on QP1 will have a UD header that
is too big to fit in a single inline data segment without crossing a
64 byte boundary, so split the header into two inline data segments.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Upcoming firmware introduces command interface revision 3, which
changes the way port capabilities are queried and set. Update the
driver to handle both the new and old command interfaces by adding a
new MLX4_FLAG_OLD_PORT_CMDS that it is set after querying the firmware
interface revision and then using the correct interface based on the
setting of the flag.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When compacting CQ entries, we need to set the correct value of the
ownership bit in case the value is different between the index we copy
the CQE from and the index we copy it to.
Found by Ronni Zimmerman of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The calculation of max_inline_data in set_kernel_sq_size() is bogus,
since it doesn't take into account the fact that inline segments may
not cross a 64-byte boundary, and hence multiple inline segments will
probably need to be used to post large inline sends.
We don't support inline sends for kernel QPs anyway, so there's no
point in doing this calculation anyway, since the field is just zeroed
out a little later. So just delete the bogus calculation.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
New ConnectX firmware introduces FW command interface revision 2,
which requires that for each QP, a chunk of send queue entries (the
"headroom") is kept marked as invalid, so that the HCA doesn't get
confused if it prefetches entries that haven't been posted yet. Add
code to the driver to do this, and also update the user ABI so that
userspace can request that the prefetcher be turned off for userspace
QPs (we just leave the prefetcher on for all kernel QPs).
Unfortunately, marking send queue entries this way is confuses older
firmware, so we change the driver to allow only FW command interface
revisions 2. This means that users will have to update their firmware
to work with the new driver, but the firmware is changing quickly and
the old firmware has lots of other bugs anyway, so this shouldn't be too
big a deal.
Based on a patch from Jack Morgenstein <jackm@dev.mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Doing max(1, foo) where foo is u32 generates a warning, because 1 is a
signed constant. Fix this by using 1U instead.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Cast the increment added to wq->tail when send completions are
processed to u16 to avoid using wrong values caused by standard
integer promotions.
The same bug was fixed in libmlx4 by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Make sure RQ allocation is always valid
RDMA/cma: Fix initialization of next_port
IB/mlx4: Fix zeroing of rnr_retry value in ib_modify_qp()
mlx4_core: Don't set MTT address in dMPT entries with PA set
mlx4_core: Check firmware command interface revision
IB/mthca, mlx4_core: Fix typo in comment
mlx4_core: Free catastrophic error MSI-X interrupt with correct dev_id
mlx4_core: Initialize ctx_list and ctx_lock earlier
mlx4_core: Fix CQ context layout
QPs attached to an SRQ must never have their own RQ, and QPs not
attached to SRQs must have an RQ with at least 1 entry. Enforce all
of this in set_rq_size().
Based on a patch by Eli Cohen <eli@mellanox.co.il>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The code in __mlx4_ib_modify_qp() overwrites context->params1 after
the RNR retry parameter is ORed in, which results in the RNR retry
parameter always being set to 0. Fix this by moving where we OR in
the value to later in the function, after the initial assignment of
context->params1.
Found by the Mellanox firmware group.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch converts the ipv4_devconf config members (everything except
sysctl) to an array. This allows easier manipulation which will be
needed later on to provide better management of default config values.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
mthca_free_err_wqe() currently treats both send and receive CQEs
identically if a QP is using an SRQ. But for Tavor hardware, send
CQEs with error can be chained together even if the RQ is part of SRQ,
so we may miss some CQEs.
Fix by following the WQE chain for all send CQEs even for non-SRQ QPs.
This fixes crashes in IPoIB CM:
<https://bugs.openfabrics.org//show_bug.cgi?id=604>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Due to a typo, the driver was reporting the wrong number of "actual send
WRs" after ehca_create_qp().
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We need to initialize the owner bit of send queue WQEs to hardware
ownership whenever the QP is modified from reset to init, not just
when the QP is first allocated. This avoids having the hardware
process stale WQEs when the QP is moved to reset but not destroyed and
then modified to init again.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a QP is attached to a shared receive queue (SRQ), then it doesn't
have a receive queue (RQ). So don't allocate an RQ doorbell (or map a
doorbell from userspace for userspace QPs) for that QP.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/cm: Improve local id allocation
IPoIB/cm: Fix SRQ WR leak
IB/ipoib: Fix typos in error messages
IB/mlx4: Check if SRQ is full when posting receive
IB/mlx4: Pass send queue sizes from userspace to kernel
IB/mlx4: Fix check of opcode in mlx4_ib_post_send()
mlx4_core: Fix array overrun in dump_dev_cap_flags()
IB/mlx4: Fix RESET to RESET and RESET to ERROR transitions
IB/mthca: Fix RESET to ERROR transition
IB/mlx4: Set GRH:HopLimit when sending globally routed MADs
IB/mthca: Set GRH:HopLimit when building MLX headers
IB/mlx4: Fix check of max_qp_dest_rdma in modify QP
IB/mthca: Fix use-after-free on device restart
IB/ehca: Return proper error code if register_mr fails
IPoIB: Handle P_Key table reordering
IB/core: Use start_port() and end_port()
IB/core: Add helpers for uncached GID and P_Key searches
IB/ipath: Fix potential deadlock with multicast spinlocks
IB/core: Free umem when mm is already gone
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass the number of WQEs for the send queue and their size from userspace
to the kernel to avoid having to keep the QP size calculations in sync
between the kernel driver and libmlx4. This fixes a bug seen with the
current mlx4_ib driver and current libmlx4 caused by a difference in the
calculated sizes for SQ WQEs. Also, this gives more flexibility for
userspace to experiment with using multiple WQE BBs for a single SQ WQE.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
wr->opcode is invalid if it's >= ARRAY_SIZE(mlx4_ib_opcode), not just
strictly >.
This was spotted by the Coverity checker (CID 1643).
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET back to RESET
or to the ERROR state, but mlx4 firmware does not support this and
returns an error if we try. Fix the RESET to RESET transition by
just returning 0 without doing anything, and fix RESET to ERROR by
moving the QP from RESET to INIT with dummy parameters and then
transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
According to the IB spec, a QP can be moved from RESET to the ERROR
state, but mthca firmware does not support this and returns an error if
we try. Work around this FW limitation by moving the QP from RESET to
INIT with dummy parameters and then transitioning from INIT to ERROR.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Global CM packets used by rmda_cm were being sent with a GRH:hopLimit
of zero, causing them to be dropped by the router. The problem is a
missing initialization of the hop_limit field in mthca_read_ah(),
which was called by build_mlx_header() when sending a MAD on QP1.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
max_qp_dest_rdma is already in natural units - no need to shift. This
was discovered by a test that deliberately requests more outstanding
atomic operation than the device supports.
Found by Sagi Rotem at Mellanox.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the return code of ehca_register_mr() to ENOMEM if the corresponding
firmware call fails due to out of resources. Some other error codes
were explicitly mapped to EINVAL -- just remove those cases so they
get mapped to the default case, which already returns EINVAL anyway.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Lockdep found the following potential deadlock between mcast_lock and
n_mcast_grps_lock: mcast_lock is taken from both interrupt context and
process context, so spin_lock_irqsave() must be used to take it.
n_mcast_grps_lock is only taken from process context, so at first it
seems safe to take it with plain spin_lock(); however, it also nests
inside mcast_lock, and hence we could deadlock:
cpu A cpu B
ipath_mcast_add():
spin_lock_irq(&mcast_lock);
ipath_mcast_detach():
spin_lock(&n_mcast_grps_lock);
<enter interrupt>
ipath_mcast_find():
spin_lock_irqsave(&mcast_lock);
spin_lock(&n_mcast_grps_lock);
Fix this by using spin_lock_irq() to take n_mcast_grps_lock.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
mthca_cq_clean() updates the CQ consumer index without moving CQEs
back to HW ownership. As a result, the same WRID might get reported
twice, resulting in a use-after-free. This was observed in IPoIB CM.
Fix by moving all freed CQEs to HW ownership.
This fixes <https://bugs.openfabrics.org/show_bug.cgi?id=617>
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix posting lists of > 255 receive WRs for Tavor: rq.next_ind must
be updated each doorbell, otherwise the next doorbell will use an
incorrect index.
Found by Ronni Zimmermann at Mellanox.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Scaling code is still considered experimental, so disable it by default
- Increase version to SVNEHCA_0023
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
eHCA's sysfs attributes are now being created via sysfs_create_group(),
making the process neatly table-driven. The return value is checked, thus
fixing a few compiler warnings.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- In ehca_process_eq(), we're IRQ safe throughout the whole function, so we
don't need another _irqsave in the middle of flight.
- take_over_work() is only called by comp_pool_callback(), so it can move
into the same #ifdef block.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
AQP0/1 should report qp_num={0|1} and the actual QP# should be stored
in struct ehca_qp, not the other way round.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The driver needs to always supply the "GRH present" flag to the
hypervisor, whether it's true or false. Not supplying it (i.e. not
setting the corresponding mask bit) amounts to a "perhaps", which we
don't want.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Some pSeries hypervisor versions show a race condition in the allocate
MR hCall. Serialize this call per adapter to circumvent this problem.
Signed-off-by: Joachim Fenkes <fenkes@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Once upon a time, GPIO interrupts were rare. But then a chip bug in
the waldo series forced the use of a GPIO interrupt to signal packet
reception. This greatly increased the frequency of GPIO interrupts
which have the gpio_mask bits set on the waldo chips. Other bits in
the gpio_status register are used for I2C clock and data lines, these
bits are usually on. An "unlikely" annotation leftover from the old
days was improperly applied to these bits, and an unnecessary chip
mmio read was being accessed in the interrupt fast path on waldo.
Remove the stagnant unlikely annotation in the interrupt handler and
keep a shadow copy of the gpio_mask register to avoid the slow mmio
read when testing for interruptable GPIO bits.
Signed-off-by: Arthur Jones <arthur.jones@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
uar_lock spinlock was used in mlx4_ib_cq_arm without being initialized
(this only affects 32-bit archs, because uar_lock is not used on
64-bit archs and MLX4_INIT_DOORBELL_LOCK() is a NOP).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters
IB: Put rlimit accounting struct in struct ib_umem
IB/uverbs: Export ib_umem_get()/ib_umem_release() to modules
Since nonboot CPUs are now disabled after tasks and devices have been
frozen and the CPU hotplug infrastructure is used for this purpose, we need
special CPU hotplug notifications that will help the CPU-hotplug-aware
subsystems distinguish normal CPU hotplug events from CPU hotplug events
related to a system-wide suspend or resume operation in progress. This
patch introduces such notifications and causes them to be used during
suspend and resume transitions. It also changes all of the
CPU-hotplug-aware subsystems to take these notifications into consideration
(for now they are handled in the same way as the corresponding "normal"
ones).
[oleg@tv-sign.ru: cleanups]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add an InfiniBand driver for Mellanox ConnectX adapters. Because
these adapters can also be used as ethernet NICs and Fibre Channel
HBAs, the driver is split into two modules:
mlx4_core: Handles low-level things like device initialization and
processing firmware commands. Also controls resource allocation
so that the InfiniBand, ethernet and FC functions can share a
device without stepping on each other.
mlx4_ib: Handles InfiniBand-specific things; plugs into the
InfiniBand midlayer.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Export ib_umem_get()/ib_umem_release() and put low-level drivers in
control of when to call ib_umem_get() to pin and DMA map userspace,
rather than always calling it in ib_uverbs_reg_mr() before calling the
low-level driver's reg_user_mr method.
Also move these functions to be in the ib_core module instead of
ib_uverbs, so that driver modules using them do not depend on
ib_uverbs.
This has a number of advantages:
- It is better design from the standpoint of making generic code a
library that can be used or overridden by device-specific code as
the details of specific devices dictate.
- Drivers that do not need to pin userspace memory regions do not
need to take the performance hit of calling ib_mem_get(). For
example, although I have not tried to implement it in this patch,
the ipath driver should be able to avoid pinning memory and just
use copy_{to,from}_user() to access userspace memory regions.
- Buffers that need special mapping treatment can be identified by
the low-level driver. For example, it may be possible to solve
some Altix-specific memory ordering issues with mthca CQs in
userspace by mapping CQ buffers with extra flags.
- Drivers that need to pin and DMA map userspace memory for things
other than memory regions can use ib_umem_get() directly, instead
of hacks using extra parameters to their reg_phys_mr method. For
example, the mlx4 driver that is pending being merged needs to pin
and DMA map QP and CQ buffers, but it does not need to create a
memory key for these buffers. So the cleanest solution is for mlx4
to call ib_umem_get() in the create_qp and create_cq methods.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch makes it so that simple_fill_super and get_sb_pseudo assign their
root inodes to be number 1. It also fixes up a couple of callers of
simple_fill_super that were passing in files arrays that had an index at
number 1, and adds a warning for any caller that sends in such an array.
It would have been nice to have made it so that it wasn't possible to make
such a collision, but some callers need to be able to control what inode
number their entries get, so I think this is the best that can be done.
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB: Convert to NAPI
IB: Return "maybe missed event" hint from ib_req_notify_cq()
IB: Add CQ comp_vector support
IB/ipath: Fix a race condition when generating ACKs
IB/ipath: Fix two more spin lock problems
IB/fmr_pool: Add prefix to all printks
IB/srp: Set proc_name
IB/srp: Add orig_dgid sysfs attribute to scsi_host
IPoIB/cm: Don't crash if remote side uses one QP for both directions
RDMA/cxgb3: Support for new abort logic
RDMA/cxgb3: Initialize cpu_idx field in cpl_close_listserv_req message
RDMA/cxgb3: Fail qp creation if the requested max_inline is too large
RDMA/cxgb3: Fix TERM codes
IPoIB/cm: Fix error handling in ipoib_cm_dev_open()
IB/ipath: Don't corrupt pending mmap list when unmapped objects are freed
IB/mthca: Work around kernel QP starvation
IB/ipath: Don't put QP in timeout queue if waiting to send
IB/ipath: Don't call spin_lock_irq() from interrupt context
The semantics defined by the InfiniBand specification say that
completion events are only generated when a completions is added to a
completion queue (CQ) after completion notification is requested. In
other words, this means that the following race is possible:
while (CQ is not empty)
ib_poll_cq(CQ);
// new completion is added after while loop is exited
ib_req_notify_cq(CQ);
// no event is generated for the existing completion
To close this race, the IB spec recommends doing another poll of the
CQ after requesting notification.
However, it is not always possible to arrange code this way (for
example, we have found that NAPI for IPoIB cannot poll after
requesting notification). Also, some hardware (eg Mellanox HCAs)
actually will generate an event for completions added before the call
to ib_req_notify_cq() -- which is allowed by the spec, since there's
no way for any upper-layer consumer to know exactly when a completion
was really added -- so the extra poll of the CQ is just a waste.
Motivated by this, we add a new flag "IB_CQ_REPORT_MISSED_EVENTS" for
ib_req_notify_cq() so that it can return a hint about whether the a
completion may have been added before the request for notification.
The return value of ib_req_notify_cq() is extended so:
< 0 means an error occurred while requesting notification
== 0 means notification was requested successfully, and if
IB_CQ_REPORT_MISSED_EVENTS was passed in, then no
events were missed and it is safe to wait for another
event.
> 0 is only returned if IB_CQ_REPORT_MISSED_EVENTS was
passed in. It means that the consumer must poll the
CQ again to make sure it is empty to avoid the race
described above.
We add a flag to enable this behavior rather than turning it on
unconditionally, because checking for missed events may incur
significant overhead for some low-level drivers, and consumers that
don't care about the results of this test shouldn't be forced to pay
for the test.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a num_comp_vectors member to struct ib_device and extend
ib_create_cq() to pass in a comp_vector parameter -- this parallels
the userspace libibverbs API. Update all hardware drivers to set
num_comp_vectors to 1 and have all ULPs pass 0 for the comp_vector
value. Pass the value of num_comp_vectors to userspace rather than
hard-coding a value of 1.
We want multiple CQ event vector support (via MSI-X or similar for
adapters that can generate multiple interrupts), but it's not clear
how many vectors we want, or how we want to deal with policy issues
such as how to decide which vector to use or how to set up interrupt
affinity. This patch is useful for experimenting, since no core
changes will be necessary when updating a driver to support multiple
vectors, and we know that we want to make at least these changes
anyway.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a problem where simple ACKs can be sent ahead of RDMA read
responses thus implicitly NAKing the RDMA read.
Signed-off-by: Ralph Campbell <ralph.cambpell@qlogic.com>
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix a missing unlock in ipath_rc_rcv_resp() and remove an extra unlock
from ipath_rc_rcv_error().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages. We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message. This plugs some close races between the uP and
HW. Also update the minimum required firmware version.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
I noticed that many source files include <linux/pci.h> while they do
not appear to need it. Here is an attempt to clean it all up.
In order to find all possibly affected files, I searched for all
files including <linux/pci.h> but without any other occurence of "pci"
or "PCI". I removed the include statement from all of these, then I
compiled an allmodconfig kernel on both i386 and x86_64 and fixed the
false positives manually.
My tests covered 66% of the affected files, so there could be false
positives remaining. Untested files are:
arch/alpha/kernel/err_common.c
arch/alpha/kernel/err_ev6.c
arch/alpha/kernel/err_ev7.c
arch/ia64/sn/kernel/huberror.c
arch/ia64/sn/kernel/xpnet.c
arch/m68knommu/kernel/dma.c
arch/mips/lib/iomap.c
arch/powerpc/platforms/pseries/ras.c
arch/ppc/8260_io/enet.c
arch/ppc/8260_io/fcc_enet.c
arch/ppc/8xx_io/enet.c
arch/ppc/syslib/ppc4xx_sgdma.c
arch/sh64/mach-cayman/iomap.c
arch/xtensa/kernel/xtensa_ksyms.c
arch/xtensa/platform-iss/setup.c
drivers/i2c/busses/i2c-at91.c
drivers/i2c/busses/i2c-mpc.c
drivers/media/video/saa711x.c
drivers/misc/hdpuftrs/hdpu_cpustate.c
drivers/misc/hdpuftrs/hdpu_nexus.c
drivers/net/au1000_eth.c
drivers/net/fec_8xx/fec_main.c
drivers/net/fec_8xx/fec_mii.c
drivers/net/fs_enet/fs_enet-main.c
drivers/net/fs_enet/mac-fcc.c
drivers/net/fs_enet/mac-fec.c
drivers/net/fs_enet/mac-scc.c
drivers/net/fs_enet/mii-bitbang.c
drivers/net/fs_enet/mii-fec.c
drivers/net/ibm_emac/ibm_emac_core.c
drivers/net/lasi_82596.c
drivers/parisc/hppb.c
drivers/sbus/sbus.c
drivers/video/g364fb.c
drivers/video/platinumfb.c
drivers/video/stifb.c
drivers/video/valkyriefb.c
include/asm-arm/arch-ixp4xx/dma.h
sound/oss/au1550_ac97.c
I would welcome test reports for these files. I am fine with removing
the untested files from the patch if the general opinion is that these
changes aren't safe. The tested part would still be nice to have.
Note that this patch depends on another header fixup patch I submitted
to LKML yesterday:
[PATCH] scatterlist.h needs types.h
http://lkml.org/lkml/2007/3/01/141
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix TERMINATE layer, type, and ecode values based on
conformance testing.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix the pending mmap code so it doesn't corrupt the list of pending
mmaps and crash the machine when pending mmaps are destroyed without
first being mapped. Also, remove an unused variable, and use standard
kernel lists instead of our own homebrewed linked list implementation
to keep the pending mmap list.
Signed-off-by: Robert Walsh <robert.walsh@qlogic.com>
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
With mthca, RC QPs can starve each other and even UD QPs on the same
hardware schedule queue. As a result, userspace MPI can starve
e.g. IPoIB traffic, with netdev watchdog warnings getting printed out,
and TCP connections getting stuck or failing.
Reduce the chance of this happening by using three separate hardware
schedule queues: one for userspace RC QPs, one for kernel RC QPs, and
one for all other QPs.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This fixes a problem which causes too many RC timeouts and
retransmits.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch fixes the problem reported by Bernd Schubert <bs@q-leap.de>
with kernel debug options enabled:
BUG: at kernel/lockdep.c:1860 trace_hardirqs_on()
This was caused by using spin_lock_irq()/spin_unlock_irq() from
interrupt context. Fix all the places that might be called from
interrupts to use spin_lock_irqsave()/spin_unlock_irqrestore().
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband: (49 commits)
IB: Set class_dev->dev in core for nice device symlink
IB/ehca: Implement modify_port
IB/umad: Clarify documentation of transaction ID
IPoIB/cm: spin_lock_irqsave() -> spin_lock_irq() replacements
IB/mad: Change SMI to use enums rather than magic return codes
IB/umad: Implement GRH handling for sent/received MADs
IB/ipoib: Use ib_init_ah_from_path to initialize ah_attr
IB/sa: Set src_path_bits correctly in ib_init_ah_from_path()
IB/ucm: Simplify ib_ucm_event()
RDMA/ucma: Simplify ucma_get_event()
IB/mthca: Simplify CQ cleaning in mthca_free_qp()
IB/mthca: Fix mthca_write_mtt() on HCAs with hidden memory
IB/mthca: Update HCA firmware revisions
IB/ipath: Fix WC format drift between user and kernel space
IB/ipath: Check that a UD work request's address handle is valid
IB/ipath: Remove duplicate stuff from ipath_verbs.h
IB/ipath: Check reserved memory keys
IB/ipath: Fix unit selection when all CPU affinity bits set
IB/ipath: Don't allow QPs 0 and 1 to be opened multiple times
IB/ipath: Disable IB link earlier in shutdown sequence
...
To clearly state the intent of copying from linear sk_buffs, _offset being a
overly long variant but interesting for the sake of saving some bytes.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now to convert the last one, skb->data, that will allow many simplifications
and removal of some of the offset helpers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that it is also an offset from skb->head, reduces its size from 8 to 4 bytes
on 64bit architectures, allowing us to combine the 4 bytes hole left by the
layer headers conversion, reducing struct sk_buff size to 256 bytes, i.e. 4
64byte cachelines, and since the sk_buff slab cache is SLAB_HWCACHE_ALIGN...
:-)
Many calculations that previously required that skb->{transport,network,
mac}_header be first converted to a pointer now can be done directly, being
meaningful as offsets or pointers.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the common, open coded 'skb->h.raw = skb->data' operation, so that we can
later turn skb->h.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple cases:
skb->h.raw = skb->data;
skb->h.raw = {skb_push|[__]skb_pull}()
The next ones will handle the slightly more "complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One less thing for drivers writers to worry about.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roland Dreier