Recent commit drbd: get rid of bio_split, allow bios of "arbitrary" size
had a reference count leak: it only deactivated the first of several
activity log extents for intervals crossing extent boundaries.
This commit generalizes on bios spanning multiple activity log extents
in drbd_al_begin_io, and adds the necessary loop around lc_put in
drbd_al_complete_io as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Where "arbitrary" size is currently 1 MiB, which is the BIO_MAX_SIZE
for architectures with 4k PAGE_CACHE_SIZE (most).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We want to avoid bio_split for bios crossing activity log boundaries.
So we may need to activate two activity log extents "atomically".
drbd_al_begin_io() needs to know more than just the start sector.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
So we can initialize a clean on disk activity log area,
without the module complaining with loud assert messages
because of checksum or magic value mismatches.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Packets of type P_HAND_SHAKE define which protocol versions and features
a node supports. For clarity, call those packets P_CONNECTION_FEATURES
instead.
(This does not determine the features that a specific drbd device
supports, such as drbd protocol A, B, C.)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The first packets exchanged when a connection is established are
referred to as P_HAND_SHAKE_S and P_HAND_SHAKE_M in the code, followed
by P_HAND_SHAKE packets. To avoid confusion between these two unrelated
things, call the initial packets P_INITIAL_DATA and P_INITIAL_META.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
During a disconnect the oc variable in _conn_request_state()
could become outdated. Determin the common old state after
sleeping.
While at it, I implemented that for all parts of the state
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The receive handlers do not all handle unknown volume numbers the same
way.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
These messages can only trigger in case there is a pretty obvious
internal programming error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is no need to send protocol 80 headers to peers that understand
protocol 95 headers. Make sure that we don't send protocol 95 headers
until we have agreed upon a protocol version with our peer, though.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The pattern of receiving a fixed number of bytes and warning if a short
packet is received and the receiver has not actively been interruped is
repeated many times; clean that up.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This type is not used anywhere else.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is also checked further below in the same function.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This helps to ensure that we don't miss one of them when changing their
return value semantics.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Q: Can this case even trigger? Is failing this way any better than one
that causes a NULL pointer access?
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It actually returned the lowest volume number. While doing that
renamed a few wrongly named variables.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit breaks the API again.
Move per-volume former syncer options into disk_conf.
Move per-connection former syncer options into net_conf.
Renamed the remainign sync_conf to res_opts
Syncer settings have been changeable at runtime, so we need to prepare
for these settings to be runtime-changeable in their new home as well.
Introduce new configuration operations, and share the netlink attribute
between "attach" (create new disk) and "disk-opts" (change options).
Same for "connect" and "net-opts".
Some fields cannot be changed at runtime, however.
Introduce a new flag GENLA_F_INVARIANT to be able to trigger on that in
the generated validation and assignment functions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If drbd_adm_attach failed early, it left the CONFIG_PENDING bit on,
blocking any further conn_reconfig_start on that connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
That is necessary in case a connection does not have a volume 0
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In the context of drbd-8.4 it no longer makes sense to
dissalow that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Took the chance and converted tconn_process_done_ee() to use
idr_for_each_entry()
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This greatly simplifies deconfiguration of whole resources.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
somehow a "goto abort" was introduced with commit
drbd: Extracted is_valid_transition() out of sanitize_state()
which left drbd_req_state still holding the spin lock.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We have resources resp. connections, volumes, and minor numbers.
A config request may specifies all three of them.
If it turns out that the minor belongs to a different connection, or a
different volume number in the same connection, that configuration
request is invalid.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Follow O_CREAT semantics when creating connection or minor device/volume
objects. If we need O_CREAT|O_EXCL semantics some time down the road,
we can add NLM_F_EXCL to the netlink message flags.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Even if the connection is still established.
We should be able to reduce a volume from a replication group,
without taking the whole group offline.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Get rid of a temporary variable and, funny bitand assignment.
Just short circuit, returning false, once we encounter the first
still configured volume.
FIXME verify call sites for need of rcu_read_lock or stronger.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We want to see existing connection objects, even if they do not
currently have volumes attached.
Change the .dumpit variant of drbd_adm_get_status to iterate not over
minor devices, but over connections + volumes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we detach due to local read-error (which sets a bit in the bitmap),
stay Primary, and then re-attach (which re-reads the bitmap from disk),
we potentially lost the "out-of-sync" (or, "bad block") information in
the bitmap.
Always (try to) write out the changed bitmap pages before going diskless.
That way, we don't lose the bit for the bad block,
the next resync will fetch it from the peer, and rewrite
it locally, which may result in block reallocation in some
lower layer (or the hardware), and thereby "heal" the bad blocks.
If the bitmap writeout errors out as well, we will (again: try to)
mark the "we need a full sync" bit in our super block,
if it was a READ error; writes are covered by the activity log already.
If that superblock does not make it to disk either, we are sorry.
Maybe we just lost an entire disk or controller (or iSCSI connection),
and there actually are no bad blocks at all, so we don't need to
re-fetch from the peer, there is no "auto-healing" necessary.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
- struct drbd_conf { ... unsigned long flags; ... }
+ struct drbd_conf { ... unsigned long drbd_flags[N]; ... }
And introduce wrapper functions for test/set/clear bit operations
on this member.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The intention of force-detach is to be able to deal with a completely
unresponsive lower level IO stack, which does not even deliver error
completions anymore, but no completion at all.
In all other cases, we must still wait for the meta data IO completion.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This has not yet been observed, but conceivably, when using GFP_KERNEL
allocations from drbd_md_sync(), drbd_flush_after_epoch() or
receive_SyncParam(), we could trigger additional IO to our own device,
or an other device in a criss-cross setup, and end up in a local
deadlock, or potentially a distributed deadlock in a criss-cross setup
involving the peer blocked in a similar way waiting for us to make
progress.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The former comment arguing that GFP_KERNEL was good enough was wrong: it
did not take resize into account at all, and assumed the only path
leading here was the normal attach on a still secondary device, so no
deadlock would be possible.
Both resize on a Primary, or attach on a diskless Primary,
could potentially deadlock.
drbd_bm_resize() is called while IO to the respective device is
suspended, so we must use GFP_NOIO to avoid potential deadlock.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
"aborting" requests, or force-detaching the disk, is intended for
completely blocked/hung local backing devices which do no longer
complete requests at all, not even do error completions. In this
situation, usually a hard-reset and failover is the only way out.
By "aborting", basically faking a local error-completion,
we allow for a more graceful swichover by cleanly migrating services.
Still the affected node has to be rebooted "soon".
By completing these requests, we allow the upper layers to re-use
the associated data pages.
If later the local backing device "recovers", and now DMAs some data
from disk into the original request pages, in the best case it will
just put random data into unused pages; but typically it will corrupt
meanwhile completely unrelated data, causing all sorts of damage.
Which means delayed successful completion,
especially for READ requests,
is a reason to panic().
We assume that a delayed *error* completion is OK,
though we still will complain noisily about it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Disconnecting is a cluster wide state change. In case the peer node agrees
to the state transition, it sends back the fact on the meta-data connection
and closes both sockets.
In case the node node that initiated the state transfer sees the closing
action on the data-socket, before the P_STATE_CHG_REPLY packet, it was
going into one of the network failure states.
At least with the fencing option set to something else thatn "dont-care",
the unclean shutdown of the connection causes a short IO freeze or
a fence operation.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The DISCARD_CONCURRENT flag should be set on one node and cleared on the
other node.
As the code was before it was theoretical possible that a node accepts the
meta socket, but has to close it later on, and keeps the DISCARD_CONCURRENT
flag.
Correct this by moving the clear_bit(DISCARD_CONCURRENT) where the packet
gets sent.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We now can schedule only a specific range of sectors for online verify,
or interrupt a running verify without interrupting the connection.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
There is at least the worker context, the receiver context, the context of
receiving netlink packts and processes reading a sysfs attribute that access
the uuids.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the old code, when you allocate a bio from a bio pool you have to
implement your own destructor that knows how to find the bio pool the
bio was originally allocated from.
This adds a new field to struct bio (bi_pool) and changes
bio_alloc_bioset() to use it. This makes various bio destructors
unnecessary, so they're then deleted.
v6: Explain the temporary if statement in bio_put
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: Nicholas Bellinger <nab@linux-iscsi.org>
CC: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block-related fixes from Jens Axboe:
- Improvements to the buffered and direct write IO plugging from
Fengguang.
- Abstract out the mapping of a bio in a request, and use that to
provide a blk_bio_map_sg() helper. Useful for mapping just a bio
instead of a full request.
- Regression fix from Hugh, fixing up a patch that went into the
previous release cycle (and marked stable, too) attempting to prevent
a loop in __getblk_slow().
- Updates to discard requests, fixing up the sizing and how we align
them. Also a change to disallow merging of discard requests, since
that doesn't really work properly yet.
- A few drbd fixes.
- Documentation updates.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: replace __getblk_slow misfix by grow_dev_page fix
drbd: Write all pages of the bitmap after an online resize
drbd: Finish requests that completed while IO was frozen
drbd: fix drbd wire compatibility for empty flushes
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update tunable options in block/cfq-iosched.txt
Documentation: update missing index files in block/00-INDEX
block: move down direct IO plugging
block: remove plugging at buffered write time
block: disable discard request merge temporarily
bio: Fix potential memory leak in bio_find_or_create_slab()
block: Don't use static to define "void *p" in show_partition_start()
block: Add blk_bio_map_sg() helper
block: Introduce __blk_segment_map_sg() helper
fs/block-dev.c:fix performance regression in O_DIRECT writes to md block devices
block: split discard into aligned requests
block: reorganize rounding of max_discard_sectors
We need to write the whole bitmap after we moved the meta data
due to an online resize operation.
With the support for one peta byte devices bitmap IO was optimized
to only write out touched pages. This optimization must be turned
off when writing the bitmap after an online resize.
This issue was introduced with drbd-8.3.10.
The impact of this bug is that after an online resize, the next
resync could become larger than expected.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Requests of an acked epoch are stored on the barrier_acked_requests list. In
case the private bio of such a request completes while IO on the drbd device
is suspended [req_mod(completed_ok)] then the request stays there.
When thawing IO because the fence_peer handler returned, then we use
tl_clear() to apply the connection_lost_while_pending event to all requests
on the transfer-log and the barrier_acked_requests list.
Up to now the connection_lost_while_pending event was not applied
on requests on the barrier_acked_requests list. Fixed that.
I.e. now the connection_lost_while_pending and resend events are
applied to requests on the barrier_acked_requests list. For that
it is necessary that the resend event finishes (local only)
READS correctly.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD has a concept of request epochs or reorder-domains,
which are separated on the wire by P_BARRIER packets.
Older DRBD is not able to handle zero-sized requests at all,
so we need to map empty flushes to these drbd barriers.
These are the equivalent of empty flushes, and
by default trigger flushes on the receiving side anyways
(unless not supported or explicitly disabled),
so there is no need to handle this differently in newer drbd either.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The pdflush thread is long gone, so this patch removes references to pdflush
from drbd comments.
Cc: drbd-dev@lists.linbit.com
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Unconditionally announce FLUSH/FUA to upper layers.
If the lower layers on either node do not actually support this,
generic_make_request() will deal with it.
If this causes performance regressions on your setup,
make sure there are no volatile caches involved,
and mount -o nobarrier or equivalent.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We capped our max_bio_size respectively max_hw_sectors with
min_t(int, lower level limit, our limit);
unfortunately, some drivers, e.g. the kvm virtio block driver, initialize their
limits to "-1U", and that is of course a smaller "int" value than our limit.
Impact: we started to request 16 MB resync requests,
which lead to protocol error and a reconnect loop.
Fix all relevant constants and parameters to be unsigned int.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If you do back to back wait-sync/invalidate on a Primary in a tight loop,
during application IO load, you could trigger a race:
kernel: block drbd6: FIXME going to queue 'set_n_write from StartingSync'
but 'write from resync_finished' still pending?
Fix this by changing the order of the drbd_queue_work() and
the wake_up() in dec_ap_pending(), and adding the additional
drbd_flush_workqueue() before requesting the full sync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Occasionally, if we disconnect, we triggered this assert:
block drbd7: ASSERT FAILED tl_hash[27] == c30b0f04, expected NULL
hlist_del() happens only on master bio completion.
We used to wait for pending IO to complete before freeing tl_hash
on disconnect. We no longer do so, since we learned to "freeze"
IO on disconnect.
If the local disk is too slow, we may reach C_STANDALONE early,
and there are still some requests pending locally when we call
drbd_free_tl_hash().
If we now free the tl_hash, and later the local IO completion completes
the master bio, which then does hlist_del() and clobbers freed memory.
Do hlist_del_init() and hlist_add_fake() before kfree(tl_hash),
so the hlist_del() on master bio completion is harmless.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In case we want to hard-reset from the local-io-error handler,
we need to call it before notifying the peer or aborting local IO.
Otherwise the peer will advance its data generation UUIDs even
if secondary.
This way, local io error looks like a "regular" node crash,
which reduces the number of different failure cases.
This may be useful in a bigger picture where crashed or otherwise
"misbehaving" nodes are automatically re-deployed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Fix asserts like
block drbd0: in got_BlockAck:4634: rs_pending_cnt = -35 < 0 !
We reset the resync lru cache and related information (rs_pending_cnt),
once we successfully finished a resync or online verify, or if the
replication connection is lost.
We also need to reset it if a resync or online verify is aborted
because a lower level disk failed.
In that case the replication link is still established,
and we may still have packets queued in the network buffers
which want to touch rs_pending_cnt.
We do not have any synchronization mechanism to know for sure when all
such pending resync related packets have been drained.
To avoid this counter to go negative (and violate the ASSERT that it
will always be >= 0), just do not reset it when we lose a disk.
It is good enough to make sure it is re-initialized before the next
resync can start: reset it when we re-attach a disk.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We cache the congestion status in mdev->congestion_reason whenever
drbd_congested() was called.
Reset this cached info before reporting it when reading /proc/drbd.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the drbd worker thread is synchronously waiting for some userland
callback, we don't want some casual pageout to block on us.
Have drbd_congested() report congestion in that case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Aborting local requests (not waiting for completion from the lower level
disk) is dangerous: if the master bio has been completed to upper
layers, data pages may be re-used for other things already.
If local IO is still pending and later completes,
this may cause crashes or corrupt unrelated data.
Only abort local IO if explicitly requested.
Intended use case is a lower level device that turned into a tarpit,
not completing io requests, not even doing error completion.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We must not look at mdev->actlog, unless we have a get_ldev() reference.
It also does not make much sense to try to disconnect or pull-ahead of
the peer, if we don't have good local data.
Only even consider congestion policies, if our local disk is D_UP_TO_DATE.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a read is aborted due to force-detach of a supposedly unresponsive
local backing device, and retried on the peer, it can happen that the
local request later still completes (hopefully with an error).
As it may already have been completed to upper layers meanwhile,
it must not be retried again now.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
BUG: unable to handle kernel NULL pointer dereference at (null)
...
[<d1e17561>] ? _drbd_bm_set_bits+0x151/0x240 [drbd]
[<d1e236f8>] ? receive_bitmap+0x4f8/0xbc0 [drbd]
This fixes an off-by-one error in the receive_bitmap() path,
if run-length encoded bitmap transfer is enabled.
If the bitmap is an exact multiple of PAGE_SIZE, which means the visible
capacity of the drbd device is an exact multiple of 128 MiB (for 4k page
size), and bitmap compression (use-rle) is enabled (which became default
with 8.4), and the very last bit is dirty and reported in an rle
comressed bitmap packet, we ended up trying to kmap_atomic a page pointer
that does not exist (bitmap->bm_pages[last index + 1]).
bug introduced by:
Date: Fri Jul 24 15:33:24 2009 +0200
set bits: optimize for complete last word, fix off-by-one-word corner case
made effective by:
Date: Thu Dec 16 00:32:38 2010 +0100
drbd: get rid of unused debug code
Long time ago, we had paranoia code in the bitmap that allocated one
extra word, assigned a magic value, and checked on every occasion that
the magic value was still unchanged.
That debug code is unused, the extra long word complicates code a bit.
Get rid of it.
No-one triggered this bug in the last few years, because a large subset
of our userbase is unaffected:
* typically the last few blocks of a device are not modified
frequently, and remain unset
* use-rle was disabled by default in drbd < 8.4
* those with slightly "odd" device sizes, or
* drbd internal meta data (which will skew the device size slightly,
thus makes it harder to have a bug relevant device size)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Pull block driver updates from Jens Axboe:
"Here are the driver related changes for 3.5. It contains:
- The floppy changes from Jiri. Jiri is now also marked as the
maintainer of floppy.c, I shall be publically branding his forehead
with red hot iron at the next opportune moment.
- A batch of drbd updates and fixes from the linbit crew, as well as
fixes from others.
- Two small fixes for xen-blkfront courtesy of Jan."
* 'for-3.5/drivers' of git://git.kernel.dk/linux-block: (70 commits)
floppy: take over maintainership
floppy: remove floppy-specific O_EXCL handling
floppy: convert to delayed work and single-thread wq
xen-blkfront: module exit handling adjustments
xen-blkfront: properly name all devices
drbd: grammar fix in log message
drbd: check MODULE for THIS_MODULE
drbd: Restore the request restart logic
drbd: introduce a bio_set to allocate housekeeping bios from
drbd: remove unused define
drbd: bm_page_async_io: properly initialize page->private
drbd: use the newly introduced page pool for bitmap IO
drbd: add page pool to be used for meta data IO
drbd: allow bitmap to change during writeout from resync_finished
drbd: fix race between drbdadm invalidate/verify and finishing resync
drbd: fix resend/resubmit of frozen IO
drbd: Ensure that data_size is not 0 before using data_size-1 as index
drbd: Delay/reject other state changes while establishing a connection
drbd: move put_ldev from __req_mod() to the endio callback
drbd: fix WRITE_ACKED_BY_PEER_AND_SIS to not set RQ_NET_DONE
...
In 2009 Philip Reiser notied that a few users of netlink connector
interface needed a capability check and added the idiom
cap_raised(nsp->eff_cap, CAP_SYS_ADMIN) to a few of them, on the premise
that netlink was asynchronous.
In 2011 Patrick McHardy noticed we were being silly because netlink is
synchronous and removed eff_cap from the netlink_skb_params and changed
the idiom to cap_raised(current_cap(), CAP_SYS_ADMIN).
Looking at those spots with a fresh eye we should be calling
capable(CAP_SYS_ADMIN). The only reason I can see for not calling capable
is that it once appeared we were not in the same task as the caller which
would have made calling capable() impossible.
In the initial user_namespace the only difference between between
cap_raised(current_cap(), CAP_SYS_ADMIN) and capable(CAP_SYS_ADMIN) are a
few sanity checks and the fact that capable(CAP_SYS_ADMIN) sets
PF_SUPERPRIV if we use the capability.
Since we are going to be using root privilege setting PF_SUPERPRIV seems
the right thing to do.
The motivation for this that patch is that in a child user namespace
cap_raised(current_cap(),...) tests your capabilities with respect to that
child user namespace not capabilities in the initial user namespace and
thus will allow processes that should be unprivielged to use the kernel
services that are only protected with cap_raised(current_cap(),..).
To fix possible user_namespace issues and to just clean up the code
replace cap_raised(current_cap(), CAP_SYS_ADMIN) with
capable(CAP_SYS_ADMIN).
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Acked-by: Andrew G. Morgan <morgan@kernel.org>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <james.l.morris@oracle.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
THIS_MODULE is NULL only when drbd is compiled as built-in,
so the #ifdef CONFIG_MODULES should be #ifdef MODULE instead.
This fixes the warning:
drivers/block/drbd/drbd_main.c: In function ‘drbd_buildtag’:
drivers/block/drbd/drbd_main.c:4187:24: warning: the comparison will always evaluate as ‘true’ for the address of ‘__this_module’ will never be NULL [-Waddress]
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It got lost with the commit 5a7bbad27a
"block: remove support for bio remapping from ->make_request"
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Don't rely on availability of bios from the global fs_bio_set,
we should use our own bio_set for meta data IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If bm_page_async_io is advised to use a new page for I/O
(BM_AIO_COPY_PAGES is set), it will get it from a mempool.
Once the mempool has to dip into its reserves the page is
not reinitialized, i.e. page->private contains garbage, which
will lead to various problems once the I/O completes (dereferences
of NULL pointers, the submitting thread getting stuck in D-state,
...).
Signed-off-by: Arne Redlich <arne.redlich@googlemail.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Symptom: messages similar to
"FIXME asender in bm_change_bits_to,
bitmap locked for 'write from resync_finished' by worker"
If a resync or verify is finished (or aborted), a full bitmap writeout
is triggered. If we have ongoing local IO, the bitmap may still change
during that writeout, pending and not yet processed acks may cause bits
to be cleared, while new writes may cause bits to be to be set.
To fix this, introduce the drbd_bm_write_copy_pages() variant.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When a resync or online verify is finished or aborted,
drbd does a bulk write-out of changed bitmap pages.
If *in that very moment* a new verify or resync is triggered,
this can race:
ASSERT( !test_bit(BITMAP_IO, &mdev->flags) ) in drbd_main.c
FIXME going to queue 'set_n_write from StartingSync' but 'write from resync_finished' still pending?
and similar.
This can be observed with e.g. tight invalidate loops in test scripts,
and probably has no real-life implication.
Still, that race can be solved by first quiescen the device,
before starting a new resync or verify.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD can freeze IO, due to fencing policy (fencing resource-and-stonith),
or because we lost access to data (on-no-data-accessible suspend-io).
Resuming from there (re-connect, or re-attach, or explicit admin
intervention) should "just work".
Unfortunately, if the re-attach/re-connect did not happen within
the timeout, since the commit
drbd: Implemented real timeout checking for request processing time
if so configured, the request_timer_fn() would timeout and
detach/disconnect virtually immediately.
This change tracks the most recent attach and connect, and does not
timeout within <configured timeout interval> after attach/connect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This could be exploited by a peer which runs modified code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Changes to the role and disk state should be delayed or rejected
while we establish a connection.
This is necessary, since the peer will base its resync decision
on the UUIDs and the state we sent in the drbd_connect() function.
The most prominent example for this race is becoming primary after
sending state and UUIDs and before the state changes to C_WF_CONNECTION.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
One invocation in the endio handler is good enough,
we don't need mention it for each of the different ways
it calls __req_mod().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Just because this request happened during a resync does
not mean it may pretend to have been barrier-acked.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
READ_RETRY_REMOTE_CANCELED needs to be grouped with the other _CANCELED
cases, not with CONNECTION_LOST_WHILE_PENDING, as that would complete
(fail) the bio even if the device became suspended.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
OOS_HANDED_TO_NETWORK should not be grouped with the various
*_CANCELED/*_FAILED cases.
Also, not only clear the RQ_NET_QUEUED flag, but also mark it RQ_NET_DONE,
so it can be distinguished from a local-only request even after that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We used to have a barrier implementation where barrier_nr 0 was
reserved. That is long gone. Just use the full sequence space.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We assumed only bios with bi_idx == 0 would end up
in drbd_make_request().
That is wrong.
At least device mapper, in __clone_and_map(), may submit
clones only covering a partial bio, but sharing
the original bvec, by adjusting bi_idx and relevant
other bio members of the clone.
We used __bio_for_each_segment() in various places,
even though that is documented as
* drivers should not use the __ version unless they _really_ want to
* run through the entire bio and not just pending pieces
Impact: we would send the full bio bvec, even for the clone
with bi_idx > 0, which will cause data corruption on the
peer (because we submit wrong data at the clone offset),
and will cause a DRBD protocol error, disconnect/reconnect
and resync (thus fixing the corruption),
because the next package header would be expected right
in the middle of the sent data, causing DRBD magic mismatch.
Fix: drop the assert, and use bio_for_each_segment()
instead of the __ version.
Conflicts:
drbd/drbd_tracing.c
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a SyncTarget node gets a P_RS_DATA_REPLY before a P_DATA packet
for the same sector, it simply submits these two IO requests.
This is be possible because on the SyncSource node, the data of the
P_RS_DATA_REPLY packet was read from disk. Immediately after that a
write request from upper layers came in.
The disk scheduler or even the "hardware" queues on the disk drive might
reorder these writes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When we have a write request and a state change C_WF_BITMAP_S -> C_SYNC_SOURCE
at the same time, and it happens that the line
remote = remote && drbd_should_do_remote(s);
stills sees C_WF_BITMAP_S, and
send_oos = rw == WRITE && drbd_should_send_oos(s);
already sees C_SYNC_SOURCE both are 0.
This causes the write to not be mirrored, but marked as out-of-sync on the
Sync_Source node.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Without this, iostat frequently sees bogus svctime and >= 100% "utilization".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_accept was modelled after kernel_accept
with drbd commit 53eb779 in July 2008.
Only, kernel_accept was then broken, and only fixed later
with kernel commit 1b08534e in Dec 2008:
net: Fix module refcount leak in kernel_accept()
Impact: protocol families provided as modules, e.g. ipv6 or ib_sdp,
would soon have their reference count become negative, preventing
them from being unloaded (likely), or worse, hit zero without actually
being unused, allowing them to be unloaded while still in use (unlikely,
but if triggered, causing a kernel crash).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the backing device is already frozen during attach, we failed
to recognize that. The current disk-timeout code works on top
of the drbd_request objects. During attach we do not allow IO
and therefore never generate a drbd_request object but block
before that in drbd_make_request().
This patch adds the timeout to all drbd_md_sync_page_io().
Before this patch we used to go from D_ATTACHING directly
to D_DISKLESS if IO failed during attach. We can no longer
do this since we have to stay in D_FAILED until all IO
ops issued to the backing device returned.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
I.e. in C_WF_REPORT_PARAMS or in C_WF_CONNECTION.
Sending may already work in these cstates, but the peer still expects
the HandShake / ConnectionFeatures packet.
Actually triggered by the Testuite on kugel.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the asender thread, or request_timer_fn(), or some other part of
the code, decided to drop the connection (because of timeout or other),
but the receiver just now was processing a P_STATE packet, there was a
chance that receive_state() would do a hard state change
"re-establishing" an already failed connection without additional handshake.
Log excerpt:
Remote failed to finish a request within ko-count * timeout
peer( Secondary -> Unknown ) conn( Connected -> Timeout ) pdsk( UpToDate -> DUnknown )
asender terminated
...
peer( Unknown -> Secondary ) conn( Timeout -> Connected ) pdsk( DUnknown -> UpToDate ) peer_isp( 0 -> 1 )
...
Connection closed
peer( Secondary -> Unknown ) conn( Connected -> Unconnected ) pdsk( UpToDate -> DUnknown ) peer_isp( 1 -> 0 )
receiver terminated
Impact:
while the connection state is erroneously "Connected",
requests may be queued and even sent,
which would never be acknowledged,
and may have been missed by the cleanup.
These requests would never be completed.
The next drbd_suspend_io() will then lock up,
waiting forever for these requests to complete.
Fixed in several code paths:
Make sure the connection state is NetworkFailure or worse
before starting the cleanup in drbd_disconnect().
This should make sure the cleanup won't miss any requests.
Disallow receive_state() to "upgrade" the connection state
from an error state. This will make sure the "illegal" state
transition won't happen.
For all connection failure states,
relax the safe-guard in sanitize_state() again
to silently mask out those state changes
(e.g. Timeout -> Connected becomes Timeout -> Timeout).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_try_clear_on_disk_bm() has a sanity check for the number of blocks
left to be resynced (rs_left) in the current resync extent.
If it detects a mismatch, it complains, and forces a disconnect using
drbd_force_state(mdev, NS(conn, C_DISCONNECTING));
Unfortunately, this may be called while holding the req_lock,
and drbd_force_state() want's to aquire that lock itself. Deadlock.
Don't force a disconnect, but fix up rs_left by recounting and
reassigning the number of dirty blocks in that extent.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This bug might have caused troubles if disk-barriers and the ahead-behind
more are enabled at the same time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD state changes schedule after_state_ch() actions to a worker thread,
which decides on the old and new states of that change, whether to send
an informational state update packet (P_STATE) to the peer.
If it decides to drbd_send_state(), it would however always send the
_curent_ state, which, if a second state change happens before the
after_state_ch() of the first ran, may "fast-forward" the peer's view
about this node. In most cases that is harmless, but sometimes this can
confuse DRBD, for example into not actually starting a necessary resync
if you do a very tight detach/attach loop on a Connected Secondary.
Fix this by always sending the "new" state of the respective state
transition which scheduled this after_state_ch() work.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When detaching, even cleanly detaching due to administrator request,
we always go through D_FAILED before we become D_DISKLESS.
Don't let that state change race with an in-flight meta data IO,
or that one might think it actually experienced an IO error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_state_lock() is only there to serialize cluster wide state
changes. Testing the local disk state needs to happen while
holding the global_state_lock.
Otherwise you might see something like this (Oct 6 on kugel)
14:20:24 drbd0: conn( WFSyncUUID -> Connected ) disk( Inconsistent -> Failed )
14:20:24 drbd0: helper command: /sbin/drbdadm before-resync-target minor-0 exit code 0 (0x0)
14:20:24 drbd0: conn( Connected -> SyncTarget ) disk( Failed -> Inconsistent )
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We have one pre-allocated page to do certain synchronous meta data IO with,
using it is serialized like so:
drbd_md_get_buffer();
drbd_md_sync_page_io();
drbd_md_sync_page_io();
...
drbd_md_put_buffer();
In drbd_md_sync_page_io() there is an
ASSERT(atomic_read(&mdev->md_io_in_use) == 1);
We want to be able to timeout on unresponsive lower level devices, so we
can "detach" in that case. Inside drbd_md_sync_page_io() we grab an extra
reference, to not have a dangling pointer in case a delayed IO eventually
does still complete, even after we "detached" already.
We need to put the extra reference before we signal completion from the
completion handler, or the second drbd_md_sync_page_io() above may
trigger the assert (reference count still 2).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With sync-after dependencies, given "lucky" timing of pause/unpause
events, and the end of an empty (0 bits set) resync was sometimes not
detected on the SyncTarget, leading to a "stalled" SyncSource state.
Fixed this by expecting not only "Inconsistent -> UpToDate" but also
"Consistent -> UpToDate" transitions for the peer disk state
to end a resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we get into the C_BROKEN_PIPE cstate once, the state engine set the
thi->t_state of the receiver thread to restarting. But with the while loop
in drbdd_init() a new connection gets established. After the call into
drbdd() returns immediately since the thi->t_state is not RUNNING. The
restart of drbd_init() then resets thi->t_state to RUNNING.
I.e. after entering C_BROKEN_PIPE once, the next successful established
connection gets wasted.
The two parts of the fix:
* Do not cause the thread to restart if we detect the issue
with the sockets while we are in C_WF_CONNECTION.
* Make sure that all actions that would have set us to C_BROKEN_PIPE
happen before the state change to C_WF_REPORT_PARAMS.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
...when the peer has inconsistent data. In that case we failed to
clear the susp_nod flag. When the local disk was attached again
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now, the new edition of the clause only fires if a diskless
peer gets promoted.
This is a fixup for "drbd: Delayed creation of current-UUID".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Bitmap IO may happend in the context of an application write,
in the generic block IO path. We need to use GFP_NOIO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the disk-timeout is active, and it expires for a single request,
we consider the local disk as D_FAILED. Note: With this change,
I made both timeout based state transitions HARD state transitions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last bunch of commits prepared the 'detach from tar pit' feature.
With that we can be for long time in disk state FAILED. We need
to accept new IO requests during that time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The new function drbd_md_get_buffer() aborts waiting for the buffer
in case the disk failes in the meantime.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Regression introduced with 8.3.11 commit:
drbd: Take a more conservative approach when deciding max_bio_size
Never ever tell an older drbd, that we support more than 32KiB
in a single data request (packet).
Never believe an older drbd, that is supports more than 32KiB
in a single data request (packet)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The reason for this change is that, with when doing
'drbdadm invalidate' on a disconnected resource caused
an "implicitly set pdsk from UpToDate to DUnknown" message,
which was missleading.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Fix warnings of the following nature in the drbd header:
In file included from drivers/block/drbd/drbd_bitmap.c:32:
drivers/block/drbd/drbd_int.h: In function 'drbd_get_syncer_progress':
drivers/block/drbd/drbd_int.h:2234: warning: comparison is always false due to limited range of data
where mdev->rs_total (an unsigned long) is being compared to 1ULL << 32, which
is always false on a 32-bit machine.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
It is not "to small", but "too small".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For large resync rates, seq_printf_with_thousands_grouping()
accidentally only produced Y,000,00Y, instead of the real numbers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Name them in a "backward compatible" manner, i.e. reuse or not
are still 1 and 0 respectively. The reuse value of 2 means that
the socket with it will forcibly reuse everyone else's port.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-3.2/core' of git://git.kernel.dk/linux-block: (29 commits)
block: don't call blk_drain_queue() if elevator is not up
blk-throttle: use queue_is_locked() instead of lockdep_is_held()
blk-throttle: Take blkcg->lock while traversing blkcg->policy_list
blk-throttle: Free up policy node associated with deleted rule
block: warn if tag is greater than real_max_depth.
block: make gendisk hold a reference to its queue
blk-flush: move the queue kick into
blk-flush: fix invalid BUG_ON in blk_insert_flush
block: Remove the control of complete cpu from bio.
block: fix a typo in the blk-cgroup.h file
block: initialize the bounce pool if high memory may be added later
block: fix request_queue lifetime handling by making blk_queue_cleanup() properly shutdown
block: drop @tsk from attempt_plug_merge() and explain sync rules
block: make get_request[_wait]() fail if queue is dead
block: reorganize throtl_get_tg() and blk_throtl_bio()
block: reorganize queue draining
block: drop unnecessary blk_get/put_queue() in scsi_cmd_ioctl() and blk_get_tg()
block: pass around REQ_* flags instead of broken down booleans during request alloc/free
block: move blk_throtl prototypes to block/blk.h
block: fix genhd refcounting in blkio_policy_parse_and_set()
...
Fix up trivial conflicts due to "mddev_t" -> "struct mddev" conversion
and making the request functions be of type "void" instead of "int" in
- drivers/md/{faulty.c,linear.c,md.c,md.h,multipath.c,raid0.c,raid1.c,raid10.c,raid5.c}
- drivers/staging/zram/zram_drv.c
This function was used to broadcast the (leading part of the)
bio payload in case we see a data integrity error. It could be received
from userland with the drbdsetup events subcommand,
to have a peek into the payload that caused the checksum mismatch,
and guess from there what may have caused the mismatch,
mainly to guess wether it was modification of in-flight data,
or data corruption by broken hardware or software bugs.
Meanwhile we support bios that are larger than the maximum payload a
netlink datagram can carry.
And we have means to reliably detect modification of in-flight data by
calculating, and comparing, the checksum before and after sendmsg.
There is no need to carry this around anymore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Still missing: rcu_readlock() on the various call sites that
access/iterate over those idrs.
We don't need a specific write lock, as we only modify from
configuration context, which is already strictly serialized.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Don't rely on availability of bios from the global fs_bio_set,
we should use our own bio_set for meta data IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit got it wrong:
drbd: Make the peer_seq updating code more obvious
Make it more clear that update_peer_seq() is supposed to wake up the
seq_wait queue whenever the sequence number changes.
We don't need to wake up everytime we receive a sequence number
that is _different_ from our currently stored "newest" sequence number,
but only if we receive a sequence number _newer_ than what we already
have, when we actually change mdev->peer_seq.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Up to now it only operated on minor numbers. Now it can work also
on named connections.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now those can be used with a struct drbd_conf * that has an other
name than 'mdev'.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Moved CONFIG_PENDING and DEVICE_DYING from mdev to tconn.
* Renamed drbd_reconfig_start() and drbd_reconfig_done() to
conn_reconfig_start() and conn_reconfig_done().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Instead of artificially enlarging the command decoding arrays to
P_MAX_CMD entries, check if an index is within the valid range using the
ARRAY_SIZE() macro.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Opening a device only succeeds on a primary node, or when explicitly
setting the allow_oos module parameter to allow opening the device
read-only on a secondary node. There is no other way that a request can
get into drbd_make_request(), so this code cannot trigger.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The previous algorithm for dealing with overlapping concurrent writes
was generating unnecessary warnings for scenarios which could be
legitimate, and did not always handle partially overlapping requests
correctly. Improve it algorithm as follows:
* While local or remote write requests are in progress, conflicting new
local write requests will be delayed (commit 82172f7).
* When a conflict between a local and remote write request is detected,
the node with the discard flag decides how to resolve the conflict: It
will ask its peer to discard conflicting requests which are fully
contained in the local request and retry requests which overlap only
partially. This involves a protocol change.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the node with the discard flag resolves write conflicts in
dual-primary mode, it may determine that its peer has sent ack packets
on the metadata socket which did not arrive, yet. Wait for the next ack
with ping-timeout instead of a hard-coded 30 seconds.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Commit 9b1e63e changed the concurrent write detection algorithm to only insert
peer requests into write_requests tree after determining that there is no
conflict. With this change, new conflicting local requests could be added
while the algorithm runs, but this case was not handled correctly. Instead of
making the algorithm deal with this case, switch back to adding peer requests
to the write_requests tree immediately: this improves fairness.
When a peer request is discarded, remove that request from the write_requests
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Summary log messages meant for global bitmap IO
should not be printed for bitmap IO caused by
activity log transactions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Use a new on-disk transaction format for the activity log, which allows
for multiple changes to the active set per transaction.
Using 4k transaction blocks, we can now get rid of the work-around code
to deal with devices not supporting 512 byte logical block size.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Allow multiple changes to the active set of elements in lru_cache.
The only current user of lru_cache, drbd, is driving this generalisation.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We are about to allow several changes to the active set in one activity
log transaction. We have to write out the corresponding bitmap pages as
well, if changed.
Introduce drbd_bm_mark_for_writeout(), then re-use the existing bitmap
writeout path to submit all marked pages in one go.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Some open-coded clear_bit(); smp_mb__after_clear_bit();
should in fact have been smp_mb__before_clear_bit(); clear_bit();
Instead, use clear_bit_unlock() to annotate the intention,
and have it do the right thing.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As using an empty activity log is the whole point of the excercise,
make sure it is still empty when setting AL_SUSPENDED.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
fold
if (x >= (N+1))
return 0;
if (x < N)
return 0;
into
if (x != N)
return 0;
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Add a macro and helper function for doing that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
That is used for graceful disconnect only
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In compatibility mode with old DRBDs, use that as the state_mutex
as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The lock they constructed is only taken when the state_mutex
was already taken. It is superficial.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
And removed the unused mdev parameter, and made the order of
the state parameters: os, ns
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
No longer work callbacks must operate on a mdev. From now on they
can also operate on a tconn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The drbd_md_sync(mdev) happens in the after state change anyways...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This reverts commit 6e9fdc92b77915d5c7ab8fea751f48378f8b0080.
1) This did not fixed the issue
2) Long sleeping work items can cause IO requests to take as long as
the longest work item
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Work items that sleep too long can cause requests to take as
long as the longest sleeping work item.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Describe how to reach any further overlapping intervals from the first
overlap found.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Make it more clear that update_peer_seq() is supposed to wake up the
seq_wait queue whenever the sequence number changes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Before submitting a new local write request, wait for any conflicting
local or remote requests to complete.
We could assume that the new request occurred first and that the
conflicting requests overwrote it (and therefore discard the new
reques), but we know for sure that the new request occurred after the
conflicting requests and so this behavior would we weird. We would also
end up with the wrong result if the new request is not fully contained
within the conflicting requests.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Nothing in this function accesses mdev->tconn->net_conf, so there is no
need for get_net_conf() / put_net_conf() anymore.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Instead of keeping a separate tree for local and remote write requests
for finding requests and for conflict detection, use the same tree for
both purposes. Introduce a flag to allow distinguishing the two
possible types of entries in this tree.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This flag is set when a processes puts itself to sleep to wait for a
conflicting request to complete.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Move drbd_update_congested() to drbd_main.c, and drbd_req_new() and
drbd_req_free() to drbd_req.c: those functions are not used anywhere
else.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
These things are only used there.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
packet_seq is initialized by both sides of a connection in
drbd_connect().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is no good reason for cmdname() to be an inline function.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now drbd communication with protocol 100 actually works.
Replaced the remaining p_header80 with p_header where we
no longer know which header it is.
In the places where p_header80 is still in use, it is on
purpose, because we know that it is an old style header
there.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The new header layout will only be used if the peer supports
it of course.
For the first packet and the handshake packet the old (h80)
layout is used for compatibility reasons.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It was pointed out by 'make versioncheck' that some includes of
linux/version.h are not needed in drivers/block/.
This patch removes them.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
There is very little benefit in allowing to let a ->make_request
instance update the bios device and sector and loop around it in
__generic_make_request when we can archive the same through calling
generic_make_request from the driver and letting the loop in
generic_make_request handle it.
Note that various drivers got the return value from ->make_request and
returned non-zero values for errors.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
recv_bm_rle_bits() should not make any assumptions abou the layout
of the packet header
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Starting to dissolve the network connection from the actual
block devices.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The open_cnt check is an open-coded D_ASSERT() check.
In case the data.work queue is not empty, it does not really help to
know which drbd_work elements remained on that list: they will be freed
immediately afterwards, anyway.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Remove the file name and line number from the syslog messages generated:
we have no duplicate function names, and no function contains the same
assertion more than once.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We do not do collision detection for read requests, but we still need to
look up the request objects when we receive a package over the network.
Using the same data structure for read and write requests results in
simpler code once the tl_hash and app_reads_hash tables are removed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Factor out duplicate code in got_NegAck().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Get rid of the ar_id_to_req() and ack_id_to_req() wrappers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Unify the ar_id_to_req() and ack_id_to_req() functions: make both fail
if the consistency check fails. Move the request lookup code now
duplicated in both functions into its own function.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Move _ar_id_to_req() to drbd_receiver.c and mark it non-inline. Remove
the leading underscores from _ar_id_to_req() and _ack_id_to_req(). Mark
ar_hash_slot() inline.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is the only place where this function is used. Make it static.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The ID_VACANT definition has become entirely irrelevant by now.
The is_syncer_block_id() macro does not improve the code, so eliminated
it.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Converting the constants happens at compile time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Converting the constants happens at compile time.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
DRBD_MAGIC has nothing to do with block ids and the funny values
computed were not actually used, anyway.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The buffer 'sc.cpu_mask' is a kernel buffer. If bitmap_parse is used
instead of __bitmap_parse the extra parameter that indicates a kernel
buffer is not needed.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
We used to write these with BIO_RW_BARRIER aka REQ_HARDBARRIER (unless
disabled in the configuration). The correct semantic now would be to
write with FLUSH/FUA.
For example, with activity log transactions, FUA alone is not enough, we
need the corresponding bitmap update (and all related application
updates) on stable storage as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we have an asymetrically congested network, we may send P_PING,
but due to congestion, the corresponding P_PING_ACK would time out,
and we would drop a (congested, but otherwise) healthy connection
("PingAck did not arrive in time.")
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we have a good resync rate, we will frequently update the on-disk
bitmap, which, if not accounted for as resync io, may let an otherwise
idle device appear to be "busy", and cause us to throttle resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last commit, drbd: add missing spinlock to bitmap receive,
introduced a cond_resched_lock(), where the lock in question is taken
with irqs disabled.
As we must not schedule with IRQs disabled,
and cond_resched_lock_irq() does not exist, yet,
we re-aquire the spin_lock_irq() for each bitmap page processed in turn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
During bitmap exchange, when using the RLE bitmap compression scheme,
we have a code path that can set the whole bitmap at once.
To avoid holding spin_lock_irq() for too long, we used to lock out other
bitmap modifications during bitmap exchange by other means, and then,
knowing we have exclusive access to the bitmap, modify it without
the spinlock, and with IRQs enabled.
Since we now allow local IO to continue, potentially setting additional
bits during the bitmap receive phase, this is no longer true, and we get
uncoordinated updates of bitmap members, causing bm_set to no longer
accurately reflect the total number of set bits.
To actually see this, you'd need to have a large bitmap, use RLE bitmap
compression, and have busy IO during sync handshake and bitmap exchange.
Fix this by taking the spin_lock_irq() in this code path as well, but
calling cond_resched_lock() after each page worth of bits processed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* 'for-2.6.40/drivers' of git://git.kernel.dk/linux-2.6-block: (110 commits)
loop: handle on-demand devices correctly
loop: limit 'max_part' module param to DISK_MAX_PARTS
drbd: fix warning
drbd: fix warning
drbd: Fix spelling
drbd: fix schedule in atomic
drbd: Take a more conservative approach when deciding max_bio_size
drbd: Fixed state transitions after async outdate-peer-handler returned
drbd: Disallow the peer_disk_state to be D_OUTDATED while connected
drbd: Fix for the connection problems on high latency links
drbd: fix potential activity log refcount imbalance in error path
drbd: Only downgrade the disk state in case of disk failures
drbd: fix disconnect/reconnect loop, if ping-timeout == ping-int
drbd: fix potential distributed deadlock
lru_cache.h: fix comments referring to ts_ instead of lc_
drbd: Fix for application IO with the on-io-error=pass-on policy
xen/p2m: Add EXPORT_SYMBOL_GPL to the M2P override functions.
xen/p2m/m2p/gnttab: Support GNTMAP_host_map in the M2P override.
xen/blkback: don't fail empty barrier requests
xen/blkback: fix xenbus_transaction_start() hang caused by double xenbus_transaction_end()
...
In file included from drivers/block/drbd/drbd_main.c:54: drivers/block/drbd/drbd_int.h:1190: warning: parameter has incomplete type
Forward declarations of enums do not work.
Fix it unpleasantly by moving the prototype.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Lars Ellenberg <drbd-dev@lists.linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Andreas Gruenbacher