Pull ARM updates from Russell King:
- add support for ELF fdpic binaries on both MMU and noMMU platforms
- linker script cleanups
- support for compressed .data section for XIP images
- discard memblock arrays when possible
- various cleanups
- atomic DMA pool updates
- better diagnostics of missing/corrupt device tree
- export information to allow userspace kexec tool to place images more
inteligently, so that the device tree isn't overwritten by the
booting kernel
- make early_printk more efficient on semihosted systems
- noMMU cleanups
- SA1111 PCMCIA update in preparation for further cleanups
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (38 commits)
ARM: 8719/1: NOMMU: work around maybe-uninitialized warning
ARM: 8717/2: debug printch/printascii: translate '\n' to "\r\n" not "\n\r"
ARM: 8713/1: NOMMU: Support MPU in XIP configuration
ARM: 8712/1: NOMMU: Use more MPU regions to cover memory
ARM: 8711/1: V7M: Add support for MPU to M-class
ARM: 8710/1: Kconfig: Kill CONFIG_VECTORS_BASE
ARM: 8709/1: NOMMU: Disallow MPU for XIP
ARM: 8708/1: NOMMU: Rework MPU to be mostly done in C
ARM: 8707/1: NOMMU: Update MPU accessors to use cp15 helpers
ARM: 8706/1: NOMMU: Move out MPU setup in separate module
ARM: 8702/1: head-common.S: Clear lr before jumping to start_kernel()
ARM: 8705/1: early_printk: use printascii() rather than printch()
ARM: 8703/1: debug.S: move hexbuf to a writable section
ARM: add additional table to compressed kernel
ARM: decompressor: fix BSS size calculation
pcmcia: sa1111: remove special sa1111 mmio accessors
pcmcia: sa1111: use sa1111_get_irq() to obtain IRQ resources
ARM: better diagnostics with missing/corrupt dtb
ARM: 8699/1: dma-mapping: Remove init_dma_coherent_pool_size()
ARM: 8698/1: dma-mapping: Mark atomic_pool as __ro_after_init
..
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Having MPU handling code in dedicated module makes it easier to
enhance/maintain it.
Tested-by: Szemző András <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
R/M classes of cpus can have memory covered by MPU which in turn might
configure RAM as Normal i.e. bufferable and cacheable. It breaks
dma_alloc_coherent() and friends, since data can stuck in caches now
or be buffered.
This patch factors out DMA support for NOMMU configuration into
separate entity which provides dedicated dma_ops. We have to handle
there several cases:
- configurations with MMU/MPU setup
- configurations without MMU/MPU setup
- special case for M-class, since caches and MPU there are optional
In general we rely on default DMA area for coherent allocations or/and
per-device memory reserves suitable for coherent DMA, so if such
regions are set coherent allocations go from there.
In case MMU/MPU was not setup we fallback to normal page allocator for
DMA memory allocation.
In case we run M-class cpus, for configuration without cache support
(like Cortex-M3/M4) dma operations are forced to be coherent and wired
with dma-noop (such decision is made based on cacheid global
variable); however, if caches are detected there and no DMA coherent
region is given (either default or per-device), dma is disallowed even
MPU is not set - it is because M-class implement system memory map
which defines part of address space as Normal memory.
Reported-by: Alexandre Torgue <alexandre.torgue@st.com>
Reported-by: Andras Szemzo <sza@esh.hu>
Tested-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Tested-by: Andras Szemzo <sza@esh.hu>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
[hch: removed the dma_supported() implementation that isn't required anymore]
Signed-off-by: Christoph Hellwig <hch@lst.de>
x86 has an option: CONFIG_DEBUG_VIRTUAL to do additional checks on
virt_to_phys calls. The goal is to catch users who are calling
virt_to_phys on non-linear addresses immediately. This includes caller
using __virt_to_phys() on image addresses instead of __pa_symbol(). This
is a generally useful debug feature to spot bad code (particulary in
drivers).
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The L2C-220 (AKA L220) and L2C-310 (AKA PL310) cache controllers feature
a Performance Monitoring Unit (PMU), which can be useful for tuning
and/or debugging. This hardware is always present and the relevant
registers are accessible to non-secure accesses. Thus, no special
firmware interface is necessary.
This patch adds support for the PMU, plugging into the usual perf
infrastructure. The overflow interrupt is not always available (e.g. on
RealView PBX A9 it is not wired up at all), and the hardware counters
saturate, so the driver does not make use of this. Instead, the driver
periodically polls and reset counters as required to avoid losing
events due to saturation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Pawel Moll <pawel.moll@arm.com>
Tested-by: Kim Phillips <kim.phillips@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch does the plumbing required to invoke the V7M cache code added
in earlier patches in this series, although there is no users for that
yet.
In order to honour the I/D cache disable config options, this patch changes
the mechanism by which the CCR is set on boot, to be more like V7A/R.
Signed-off-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Tested-by: Andras Szemzo <sza@esh.hu>
Tested-by: Joachim Eastwood <manabian@gmail.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This commit adds support for UniPhier outer cache controller.
All the UniPhier SoCs are equipped with the L2 cache, while the L3
cache is currently only integrated on PH1-Pro5 SoC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Re-implement the physical address space switching to be architecturally
compliant. This involves flushing the caches, disabling the MMU, and
only then updating the page tables. Once that is complete, the system
can be brought back up again.
Since we disable the MMU, we need to do the update in assembly code.
Luckily, the entries which need updating are fairly trivial, and are
all setup by the early assembly code. We can merely adjust each entry
by the delta required.
Not only does this fix the code to be architecturally compliant, but it
fixes a couple of bugs too:
1. The original code would only ever update the first L2 entry covering
a fraction of the kernel; the remainder were left untouched.
2. The L2 entries covering the DTB blob were likewise untouched.
This solution fixes up all entries.
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The feroceon copypage implementation cannot be built when targetting an
ARMv4 CPU, so we need to pass the march=armv5te flag manually to gcc
when building this file. This is obviously safe since that code will
not be executed on ARMv4.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
set_memory_* functions have same implementation
except memory attribute.
This patch makes to use common function for these, and pull out
the functions into arch/arm/mm/pageattr.c like arm64 did.
It will reduce code size and enhance the readability.
Signed-off-by: Jungseung Lee <js07.lee@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide a common assembly implementation for PL310 resume code. Certain
platforms need to re-initialise the L2C cache early as it may preserve
data across a S2RAM cycle, and therefore must be enabled along with the
L1 cache and MMU.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch allows the kernel page tables to be dumped via a debugfs file,
allowing kernel developers to check the layout of the kernel page tables
and the verify the various permissions and type settings.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These changes bring both HugeTLB support and Transparent HugePage
(THP) support to ARM. Only long descriptors (LPAE) are supported
in this series.
The code has been tested on an Arndale board (Exynos 5250).
This patch adds support for hugetlbfs based on the x86 implementation.
It allows mapping of 2MB sections (see Documentation/vm/hugetlbpage.txt
for usage). The 64K pages configuration is not supported (section size
is 512MB in this case).
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
[steve.capper@linaro.org: symbolic constants replace numbers in places.
Split up into multiple files, to simplify future non-LPAE support,
removed huge_pmd_share code, as this is very rarely executed,
Added PROT_NONE support].
Signed-off-by: Steve Capper <steve.capper@linaro.org>
Reviewed-by: Will Deacon <will.deacon@arm.com>
Pull ARM-v7M support from Uwe Kleine-König:
"All but the last patch were in next since next-20130418 without issues.
The last patch fixes a problem in combination with
8164f7a (ARM: 7680/1: Detect support for SDIV/UDIV from ISAR0 register)
which triggers a WARN_ON without an implemented read_cpuid_ext.
The branch merges fine into v3.10-rc1 and I'd be happy if you pulled it
for 3.11-rc1. The only missing piece to be able to run a Cortex-M3 is
the irqchip driver that will go in via Thomas Gleixner and platform
specific stuff."
This patch modifies the required Kconfig and Makefile files to allow the
building of kernel for Cortex-M3.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Jonathan Austin <jonathan.austin@arm.com>
Tested-by: Jonathan Austin <jonathan.austin@arm.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
This is only used by 740t, which is a v4 core and (by my reading of the
datasheet for the CPU) ignores CRm for the cp15 cache flush operation,
making the v4 cache implementation in cache-v4.S sufficient for this
CPU.
Tested with 740T core-tile on Integrator/AP baseboard.
Acked-by: Hyok S. Choi <hyok.choi@samsung.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now, there is no user for vmregion.
So remove it.
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch removes support for ARMv3 CPUs, which haven't worked properly
for quite some time (see the FIXME comment in arch/arm/mm/fault.c). The
only V3 parts left is the cache model for ARMv3, which is needed for some
odd reason by ARM740T CPUs, and being able to build with -march=armv3,
which is required for the RiscPC platform due to its bus structure.
Acked-by: Will Deacon <will.deacon@arm.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a CPU_V6K configuration option for platforms to select if they
have a V6K CPU core. This allows us to identify whether we need to
support ARMv6 CPUs without the V6K SMP extensions at build time.
Currently CPU_V6K is just an alias for CPU_V6, and all places which
reference CPU_V6 are replaced by (CPU_V6 || CPU_V6K).
Select CPU_V6K from platforms which are known to be V6K-only.
Acked-by: Tony Lindgren <tony@atomide.com>
Tested-by: Sourav Poddar <sourav.poddar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have two places where we create identity mappings - one when we bring
secondary CPUs online, and one where we setup some mappings for soft-
reboot. Combine these two into a single implementation. Also collect
the identity mapping deletion function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Everything should now be using sparsemem rather than discontigmem, so
remove the code supporting discontigmem from ARM.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Tauros2 L2 cache controller as used with the PJ1
and PJ4 CPUs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Instruction fault status register, IFSR, was introduced on ARMv6 to
provide status information about the last insturction fault. It
needed for proper prefetch abort handling.
Now we have three prefetch abort model:
* legacy - for CPUs before ARMv6. They doesn't provide neither
IFSR nor IFAR. We simulate IFSR with section translation fault
status for them to generalize code;
* ARMv6 - provides IFSR, but not IFAR;
* ARMv7 - provides both IFSR and IFAR.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Adds support for Faraday FA526 core. This core is used at least by:
Cortina Systems Gemini and Centroid family
Cavium Networks ECONA family
Grain Media GM8120
Pixelplus ImageARM
Prolific PL-1029
Faraday IP evaluation boards
v2:
- move TLB_BTB to separate patch
- update copyrights
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
"""The Marvell® PXA168 processor is the first in a family of application
processors targeted at mass market opportunities in computing and consumer
devices. It balances high computing and multimedia performance with low
power consumption to support extended battery life, and includes a wealth
of integrated peripherals to reduce overall BOM cost .... """
See http://www.marvell.com/featured/pxa168.jsp for more information.
1. Marvell Mohawk core is a hybrid of xscale3 and its own ARM core,
there are many enhancements like instructions for flushing the
whole D-cache, and so on
2. Clock reuses Russell's common clkdev, and added the basic support
for UART1/2.
3. Devices are a bit different from the 'mach-pxa' way, the platform
devices are now dynamically allocated only when necessary (i.e.
when pxa_register_device() is called). Description for each device
are stored in an array of 'struct pxa_device_desc'. Now that:
a. this array of device description is marked with __initdata and
can be freed up system is fully up
b. which means board code has to add all needed devices early in
his initializing function
c. platform specific data can now be marked as __initdata since
they are allocated and copied by platform_device_add_data()
4. only the basic UART1/2/3 are added, more devices will come later.
Signed-off-by: Jason Chagas <chagas@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The kmap virtual area borrows a 2MB range at the top of the 16MB area
below PAGE_OFFSET currently reserved for kernel modules and/or the
XIP kernel. This 2MB corresponds to the range covered by 2 consecutive
second-level page tables, or a single pmd entry as seen by the Linux
page table abstraction. Because XIP kernels are unlikely to be seen
on systems needing highmem support, there shouldn't be any shortage of
VM space for modules (14 MB for modules is still way more than twice the
typical usage).
Because the virtual mapping of highmem pages can go away at any moment
after kunmap() is called on them, we need to bypass the delayed cache
flushing provided by flush_dcache_page() in that case.
The atomic kmap versions are based on fixmaps, and
__cpuc_flush_dcache_page() is used directly in that case.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.
This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.
CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:
a. _only_ PXA300/PXA310 support included and no L2 cache wanted
b. PXA320 support included, but want L2 be disabled
So the enabling of L2 depends on two things:
- CACHE_XSC3L2 is selected
- and L2 cache is present
Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).
IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.
Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:
- OC bits in TTBASE register (table walk outer cache attributes)
- LLR Outer Cache Attributes (OC) in Auxiliary Control Register
Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for the unified Feroceon L2 cache controller
as found in e.g. the Marvell Kirkwood and Marvell Discovery Duo
families of ARM SoCs.
Note that:
- Page table walks are outer uncacheable on Kirkwood and Discovery
Duo, since the ARMv5 spec provides no way to indicate outer
cacheability of page table walks (specifying it in TTBR[4:3] is
an ARMv6+ feature).
This requires adding L2 cache clean instructions to
proc-feroceon.S (dcache_clean_area(), set_pte()) as well as to
tlbflush.h ({flush,clean}_pmd_entry()). The latter case is handled
by defining a new TLB type (TLB_FEROCEON) which is almost identical
to the v4wbi one but provides a TLB_L2CLEAN_FR flag.
- The Feroceon L2 cache controller supports L2 range (i.e. 'clean L2
range by MVA' and 'invalidate L2 range by MVA') operations, and this
patch uses those range operations for all Linux outer cache
operations, as they are faster than the regular per-line operations.
L2 range operations are not interruptible on this hardware, which
avoids potential livelock issues, but can be bad for interrupt
latency, so there is a compile-time tunable (MAX_RANGE_SIZE) which
allows you to select the maximum range size to operate on at once.
(Valid range is between one cache line and one 4KiB page, and must
be a multiple of the line size.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
This patch implements a set of Feroceon-specific
{copy,clear}_user_page() routines that perform more optimally than
the generic implementations. This also deals with write-allocate
caches (Feroceon can run L1 D in WA mode) which otherwise prevents
Linux from booting.
[nico: optimized the code even further]
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Sylver Bruneau <sylver.bruneau@googlemail.com>
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Feroceon is a family of independent ARMv5TE compliant CPU core
implementations, supporting a variable depth pipeline and out-of-order
execution. The Feroceon is configurable with VFP support, and the
later models in the series are superscalar with up to two instructions
per clock cycle.
This patch adds the initial low-level cache/TLB handling for this core.
Signed-off-by: Assaf Hoffman <hoffman@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Nicolas Pitre <nico@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
We are currently using the ARMv6 operations but need to duplicate some
of the code because of the introduction of the new CPU barrier
instructions in ARMv7.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the necessary lines to the Makefile and Kconfig files for
enabling the compilation of the ARMv7 CPU support.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the support for the L210/L220 (outer) cache
controller. The cache range operations are done by index/way since L2
cache controller only accepts physical addresses.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is no FSR/FAR register on no-CP15 or MPU cores. This patch adds a
dummy abort handler which returns zero for the base restored Data Abort
model !CPU_CP15_MMU cores. The abort-lv4t.S is still used with the fix-up
for the base updated Data Abort model cores.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ARM946E-S core support which has typically 8KB I&D cache.
It has a MPU and supports ARMv5TE instruction set.
Because the ARM946E-S core can be synthesizable with various cache size,
CONFIG_CPU_DCACHE_SIZE is defined for vendor specific configurations.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ARM940T core support which has 4KB D-cache, 4KB I-cache
and a MPU.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ARM9TDMI core support which has no cache and no CP15
register(no memory control unit).
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ARM740T core support which has a MPU and 4KB or 8KB cache.
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds ARM7TDMI core support which has no cache and no CP15
register(no memory control unit).
Signed-off-by: Hyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Linus Torvalds