Add support to configure missed beacon threshold, by default, if receive
"missed beacon" notification from uCode and has more than 5 consecutive
beacon missed, then perform sensitivity calibration; with this change,
allow user to adjust the missed beacon threshold from debugfs in case
more sensitivity calibration required for better performance in noisy
environment
The default value (=5) should be good enough for the normal condition,
but for very noisy environment, more sensitivity calibration could help
improve the throughput, so by setting the missed beacon threshold to
lower number, user might experience better performance result.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch continues the effort which began with:
"[PATCH] p54pci: move tx cleanup into tasklet".
Thanks to these changes, p54pci's interrupt & tx
cleanup routines can be made lock-less.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As all bt packets are priority traffic during bt scan, wifi
will get disconnected when bt scan lasts for few seconds. Fix
this by allocating 10% of bt period time (4.5ms) to wifi fully.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon sent gating doesn't seem to work with any combination
of flags. Thus, buffered frames tend to stay buffered forever,
using up tx descriptors.
Instead, use the DBA gating and hold transmission of the buffered
frames until 80% of the beacon interval has elapsed using the ready
time. This fixes the following error in AP mode:
ath5k phy0: no further txbuf available, dropping packet
Add a comment to acknowledge that this isn't the best solution.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using the external sleep clock in AP mode, the
TSF increments too quickly, causing beacon interval
to be much lower than it is supposed to be, resulting
in lots of beacon-not-ready interrupts.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14802.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If a device has multiple MAC addresses, userspace will
need to know about that. Similarly, if it allows the
MAC addresses to vary by a bitmask.
If a driver exports multiple addresses, it is assumed
that it will be able to deal with that many different
addresses, which need not necessarily match the ones
programmed into the device; if a mask is set then the
device should deal addresses within that mask based
on an arbitrary "base address".
To test it all and show how it is used, add support
to hwsim even though it can't actually deal with
addresses different from the default.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a TKIP key is updated, we should pass the station
pointer instead of just the address, since drivers can
use that to store their own data. We also need to pass
the virtual interface pointer.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Users wishing to tweak tx power want it to happen immediately,
try to respect that. This was tested by Lorenzo by measuring the
received signal strength from an AP with ath9k and the patch.
Changing the tx power on the AP produced these results:
1) iwconfig wlan0 txpower 20 ---> Rx power -37dbm
2) iwconfig wlan0 txpower 15 ---> Rx power -41dbm
3) iwconfig wlan0 txpower 10 ---> Rx power -45dbm
4) iwconfig wlan0 txpower 5 ---> Rx power -51dbm
5) iwconfig wlan0 txpower 0 ---> Rx power -37dbm
The result with 0 is an anomoly and would need to be
addressed through a separate patch.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Tested-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the v10 firmware running on 8688 HW, clearing WPA keys after setting the
WEP key prevents us from being able to associate with WEP APs.
Swapping the calling order for assoc_helper_wpa_keys() and
assoc_helper_wep_keys fixes that issue.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves the tx cleanup routines out of the critical
interrupt context and into the (previously known as rx) tasklet.
The main goal of this operation is to remove the extensive
usage of spin_lock_irqsaves in the generic p54common library.
The next step would be to modify p54usb to do the
rx processing inside a tasklet (just like usbnet).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds error-paths to handle pci_dma_mapping errors.
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Tx DMA descriptor has two kinds of flags that select RTS/CTS usage.
The first one (global for the frame) selects whether RTS/CTS or
CTS-to-self should be used, the second one enables RTS/CTS or
CTS-to-self usage for an individual multi-rate-retry entry.
Previously the code preparing the descriptor only enabled the global
flag, if the first MRR series selected the local one.
Fix this by enabling the global flag if any of the MRR entries need it.
With this patch, rate control can properly select the use of RTS/CTS
for all MRR entries except the first one, which is the default behavior.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When reading current ucode statistics information from debugfs, in
current implementation, it will always send a new "statistics request" to
uCode. In normal operation, uCode should report the statistics per beacon
interval. Remove this extra request to reduce the additional command exchanges
between driver and uCode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Flowhandler handle the communication between driver and uCode, when any
uCode error happen, we also like to know what is the status of the
flowhandler; it can help to debug flowhandler related problem.
Also adding debugfs file to dump current value of flowhandler registers.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a w/a for a hardware bug. the h/w bug may cause the Rx bit
(bit 15 before shifting it to 31) to clear when using interrupt coalescing.
This does not mean frames are lost - their processing is just delayed until
next interrupt arrives.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For interrupt coalescing timer, the CSR_INT_COALESCING is an 8 bit
register in 32-usec unit, the range can go from 0x00 - 0xFF. set the
range and default timeout value for both calibration mode and operation mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When dumping event log in debugfs, iwl_dump_nic_event_log()
should return the correct error code instead of let the calling
function makes it own assumption.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When uCode detects number of beacon missed consecutively above the
internal missed beacon threshold (set by uCode), it will reset and
re-tune the radio in order to get out of bad PHY state.
This "num_of_sos_states" counter monitors number of time uCode
encounters this bad condition and has to re-tune the radio.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help debug uCode related problem, adding "delta" and "max"
information in debugfs statistics counters display.
Those information show the delta between two statistics report from
uCode, user can monitor the counters for any "un-normal" behavior.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Jay Sternberg<jay.e.sternberg@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When receive reply statistics command with "clear" mask, just reset the
accumulated statistics counters, but not the current statistics counters,
so the accumulated statistics counter can provide the correct
information.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Yasuhiro ABE <yadiary@gmail.com> reported success in sourceforge zd1211-dev list.
The device is a NEC Aterm WL54GU usb wireless stick.
The brand and retail product name
NEC, Aterm PA-WL54GU
The USB ID's (duh)
ID 0409:0248
The chip ID string
zd1211rw 1-1:1.0: zd1211b chip 0409:0248 v4810 high 00-1b-8b AL2230S_RF pa0 g--N-
The FCC ID
unknown
Signed-off-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: Yasuhiro ABE <yadiary@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A long time ago, a user reported several crashes due to
data corruptions which are likely the result of a
not-100%-supported, or faulty? PCI bridge.
( http://patchwork.kernel.org/patch/53004/ )
This patch fixes entry #1.
"1. p54p_check_rx_ring - skb_over_panic: Under a ping flood
or just left running for a bit would panic with a skb_over_panic."
As described in the mail: The invalid frame length causes
skb_put to bailout and trigger a crash.
Note:
Simply dropping the frame is problematic, because if its content
contains a tx feedback we would lose some portion of the device
memory space.... And the driver/mac80211 should handle all other
invalid data.
Reported-by: Quintin Pitts <geek4linux@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to 6000 and 1000 series, RTS/CTS is the recommended protection
mechanism for 5000 series in HT mode based on the HW design.
Using RTS/CTS will better protect the inner exchange from interference,
especially in highly-congested environment, it also prevent uCode encounter
TX FIFO underrun and other HT mode related performance issues.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
CC: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Wey-Yi Guy