Add support for using TMC-ETR as backend for ETM perf tracing.
We use software double buffering at the moment. i.e, the TMC-ETR
uses a separate buffer than the perf ring buffer. The data is
copied to the perf ring buffer once a session completes.
The TMC-ETR would try to match the larger of perf ring buffer
or the ETR buffer size configured via sysfs, scaling down to
a minimum limit of 1MB.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the ETR could be driven either by SYSFS or by perf, it
becomes complicated how we deal with the buffers used for each
of these modes. The ETR driver cannot simply free the current
attached buffer without knowing the provider (i.e, sysfs vs perf).
To solve this issue, we provide:
1) the driver-mode specific etr buffer to be retained in the drvdata
2) the etr_buf for a session should be passed on when enabling the
hardware, which will be stored in drvdata->etr_buf. This will be
replaced (not free'd) as soon as the hardware is disabled, after
necessary sync operation.
The advantages of this are :
1) The common code path doesn't need to worry about how to dispose
an existing buffer, if it is about to start a new session with a
different buffer, possibly in a different mode.
2) The driver mode can control its buffers and can get access to the
saved session even when the hardware is operating in a different
mode. (e.g, we can still access a trace buffer from a sysfs mode
even if the etr is now used in perf mode, without disrupting the
current session.)
Towards this, we introduce a sysfs specific data which will hold the
etr_buf used for sysfs mode of operation, controlled solely by the
sysfs mode handling code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that we can use a CATU with a scatter gather table, add support
for the TMC ETR to make use of the connected CATU in translate mode.
This is done by adding CATU as new buffer mode.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the support for Scatter-Gather mode to the etr-buf layer.
Since we now have two different modes, we choose the backend
based on a set of conditions, documented in the code.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC-ETR can use the target trace buffer in two different modes.
Normal physically contiguous mode and a discontiguous list pages in
Scatter-Gather mode. Also we have dedicated Coresight component, CATU
(Coresight Address Translation Unit) to provide improved scatter-gather
mode in Coresight SoC-600. This complicates the management of the
buffer used for trace, depending on the mode in which ETR is configured.
So, this patch adds a transparent layer for managing the ETR buffer
which abstracts the basic operations on the buffer (alloc, free,
sync and retrieve the data) and uses the mode specific helpers to
do the actual operation. This also allows the ETR driver to choose
the best mode for a given use case and adds the flexibility to
fallback to a different mode, without duplicating the code.
The patch also adds the "normal" flat memory mode and switches
the sysfs driver to use the new layer.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a generic sg table data structure and
associated operations. An SG table can be used to map a set
of Data pages where the trace data could be stored by the TMC
ETR. The information about the data pages could be stored in
different formats, depending on the type of the underlying
SG mechanism (e.g, TMC ETR SG vs Coresight CATU). The generic
structure provides book keeping of the pages used for the data
as well as the table contents. The table should be filled by
the user of the infrastructure.
A table can be created by specifying the number of data pages
as well as the number of table pages required to hold the
pointers, where the latter could be different for different
types of tables. The pages are mapped in the appropriate dma
data direction mode (i.e, DMA_TO_DEVICE for table pages
and DMA_FROM_DEVICE for data pages). The framework can optionally
accept a set of allocated data pages (e.g, perf ring buffer) and
map them accordingly. The table and data pages are vmap'ed to allow
easier access by the drivers. The framework also provides helpers to
sync the data written to the pages with appropriate directions.
This will be later used by the TMC ETR SG unit and CATU.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment we adjust the buffer pointers for reading the trace
data via misc device in the common code for ETF/ETB and ETR. Since
we are going to change how we manage the buffer for ETR, let us
move the buffer manipulation to the respective driver files, hiding
it from the common code. We do so by adding type specific helpers
for finding the length of data and the pointer to the buffer,
for a given length at a file position.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving all kernel side CoreSight framework and drivers to SPDX identifier.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The coresight SoC 600 supports ETR save-restore which allows us
to restore a trace session by retaining the RRP/RWP/STS.Full values
when the TMC leaves the Disabled state. However, the TMC doesn't
have a scatter-gather unit in built.
Also, TMCs have different PIDs in different configurations (ETF,
ETB & ETR), unlike the previous generation.
While the DEVID exposes some of the features/changes in the TMC,
it doesn't explicitly advertises the new save-restore feature
as described above.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Coresight SoC 600 TMC ETR supports save-restore feature,
where the values of the RRP/RWP and STS.Full are retained
when it leaves the Disabled state. Hence, we must program the
RRP/RWP and STS.Full to a proper value. For now, set the RRP/RWP
to the base address of the buffer and clear the STS.Full register.
This can be later exploited for proper save-restore of ETR
trace contexts (e.g, perf).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ETR supports split cache encoding (i.e, separate bits for
read and write transfers) unlike the older version (where read
and write transfers use the same encoding in AXICTL[2-5]).
This feature is not advertised and has to be described by the
static mask associated with the device id.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up how we setup the AXICTL register on
TMC ETR. At the moment we don't set the CacheCtrl bits, which
drives the arcache and awcache bits on AXI bus specifying the
cacheablitiy. Set this to Write-back Read and Write-allocate.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TMC in Coresight SoC-600 advertises the AXI address width
in the device configuration register.
Bit 16 - AXIAW_VALID
0 - AXI Address Width not valid
1 - Valid AXI Address width in Bits[23-17]
Bits [23-17] - AXIAW. If AXIAW_VALID = b01 then
0x20 - 32bit AXI address bus
0x28 - 40bit AXI address bus
0x2c - 44bit AXI address bus
0x30 - 48bit AXI address bus
0x34 - 52bit AXI address bus
Use the address bits from the device configuration register, if
available. Otherwise, default to 40bit.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SG unit in the TMC has been removed in Coresight SoC-600.
This is however advertised by DEVID:Bit 24 = 0b1. On the
previous generation, the bit is RES0, hence we can rely on the
DEVID to detect the support.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Mike Leach <mike.leach@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With new version of TMC ETR, there are differing set of
features supported by the TMC. Add the capability of a
given TMC ETR for making safer decisions at runtime.
The device configuration register of the TMC (DEVID) lists
some of the capabilities. So, we can detect some of them at
probe. However, some of the features (or changes in behavior)
are not advertised and we have to depend on the PID to infer
the features. So we use a static description of the "unadvertised"
capabilities attached to the PID. Combining both, the static
and the dynamic capabilities, we maintain a bitmask of the
available features which can be later checked to take
appropriate actions.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Coresight TMC splits 64bit registers into a pair of 32bit registers
(e.g DBA, RRP, RWP). Provide helpers to read/write to these registers.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mode of operation of the TMC tracked in drvdata->mode is defined
as a local_t type. This is always checked and modified under the
drvdata->spinlock and hence we don't need local_t for it and the
unnecessary synchronisation instructions that comes with it. This
change makes the code a bit more cleaner.
Also fixes the order in which we update the drvdata->mode to
CS_MODE_DISABLED. i.e, in tmc_disable_etX_sink we change the
mode to CS_MODE_DISABLED before invoking tmc_disable_etX_hw()
which in turn depends on the mode to decide whether to dump the
trace to a buffer.
Applies on mathieu's coresight/next tree [1]
https://git.linaro.org/kernel/coresight.git next
Reported-by: Venkatesh Vivekanandan <venkatesh.vivekanandan@broadcom.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present the ETF or ETR gives out the entire device
buffer, even if there is less or even no trace data
available. This patch limits the trace data given out to
the actual trace data collected.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implement the AUX area interfaces required to
use the TMC (configured as an ETF) from the Perf sub-system.
The heuristic is heavily borrowed from the ETB10 implementation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing the HW configuration register each time the memory
width is needed simply doesn't make sense. It is much more
efficient to read the value once and keep a reference for
later use.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving tmc_drvdata::enable to a local_t mode. That way the
sink interface is aware of it's orgin and the foundation for
mutual exclusion between the sysFS and Perf interface can be
laid out.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allowing multiple readers to access the trace data simultaniously
via sysFS provides no shortage of opportunity for race condition,
mandates two variable to be maintained (drvdata::read_count and
drvdata::reading), makes the code complex and provide little
advantages, if any.
This patch streamlines the read process by restricting trace data
access to a single user. That way drvdata::read_count can
be eliminated and race conditions (along with faulty error handling)
in function tmc_open() and tmc_release() eliminated.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dealing with HW related matters in tmc_read_prepare/unprepare
becomes convoluted when many cases need to be handled distinctively.
As such moving processing related to HW setup to individual driver
files and keep the core driver generic.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC block can operate in 3 modes (ETB, ETF and ETR) and accessed
via two interfaces (sysFS and Perf). That makes 6 mode to cover, which
is way too much coupling for a single file.
This patch splits the original TMC driver in 2 halves, one for ETB/ETF
and another one for ETR mode. A common core is kept for functionality
common to all 3 modes.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch first move the TMC_STS_TMCREADY_BIT and
TMC_FFCR_FLUSHMAN_BIT defines to their respective section.
It also removes TMC_FFCR_FLUSHMAN, since the same result
can easily be obtained using the BIT() macro.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amount of #define, enumeration and structure definition
is big enough to justify moving them to a new header file.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Suzuki K Poulose