The checker code to iterate over all drive strength and bias register
description items is cumbersome, due to the repeated calculation of
indices, and the use of hardcoded array sizes. The latter was done
under the assumption they would never need to be changed, which turned
out to be false.
Increase readability by introducing helper macros to access drive
strength and bias register description items.
Increase maintainability by replacing hardcoded numbers by array sizes
calculated at compile-time.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/5051ae56a1388ccf2d283dfc9624de2991cce914.1650355619.git.geert+renesas@glider.be
Switch the code to use for_each_gpiochip_node() helper.
While at it, in order to avoid additional churn in the future,
switch to fwnode APIs where it makes sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Since we have generic function to count GPIO controller nodes
under a given device, there is no need to open code it. Replace
custom code by gpiochip_node_count() call.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Clock-Synchronized Serial
Interfaces with FIFO (MSIOF) on the Renesas R-Car S4-8 (R8A779F0) SoC.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/c625769714b1027a756dd2ed4a017eb24708a041.1645457792.git.geert+renesas@glider.be
Add pins, groups, and functions for the High Speed Serial Communication
Interfaces with FIFO (HSCIF) on the Renesas R-Car S4-8 (R8A779F0) SoC.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/2b85b8857c1189fa6ee33e2f57fe746d740481d1.1645457792.git.geert+renesas@glider.be
Add pins, groups, and functions for the Serial Communication Interfaces
with FIFO (SCIF) on the Renesas R-Car S4-8 (R8A779F0) SoC.
Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/6369359a53483291ee536787c8a232462ff1b3a9.1645457792.git.geert+renesas@glider.be
Add initial Pin Function Controller (PFC) support for the Renesas R-Car
S4-8 (R8A779F0) SoC, including bias, drive strength and voltage control.
Based on a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/fd8201da404b7b0897130b254380ffc97f437266.1645457792.git.geert+renesas@glider.be
Linus reports that some Renesas pin control sub-drivers are still
including <linux/gpio.h> instead of <linux/gpio/driver.h>. As these
sub-drivers don't need either, the includes can just be removed.
Reported-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/578825d779b45af745cc7623c7f69d2ddeadac4b.1645605227.git.geert+renesas@glider.be
The checker failed to validate all enum IDs in the description of a
register with fixed-width register fields, due to a miscalculation of
the number of described states: each register field of n bits can have
"1 << n" possible states, not "1".
Increase SH_PFC_MAX_ENUMS accordingly, now more enum IDs are checked
(SH-Mobile AG5 has more than 4000 enum IDs defined).
Fixes: 12d057bad6 ("pinctrl: sh-pfc: checker: Add check for enum ID conflicts")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/6d8a6a05564f38f9d20464c1c17f96e52740cf6a.1645460429.git.geert+renesas@glider.be
Validate consistency of the pin control tables for pins with I/O voltage
capabilities. If a pin has I/O voltage register bits declarations
through .pin_to_pocctrl(), the SH_PFC_PIN_CFG_IO_VOLTAGE flag should be
set in the pin's configs, and vice versa.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/de81cced01ae3f26d341177d66d4b8e918fbfb76.1640270559.git.geert+renesas@glider.be
Validate consistency of the pin control tables for pins with drive
strength capabilities. If a pin has drive strength register bits
declarations in drive_regs[], the SH_PFC_PIN_CFG_DRIVE_STRENGTH flag
should be set in the pin's configs, and vice versa.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/0d5de01b5fe2c5fd23c3bea41077dc57ad105b9e.1640270559.git.geert+renesas@glider.be
Validate consistency of the pin control tables for pins with pull-up
and/or pull-down capabilities. If a pin has bias register bits
declarations in bias_regs[] or through .pin_to_portcr(), the
corresponding SH_PFC_PIN_CFG_PULL* flags should be set in the pin's
configs, and vice versa, and the .get_bias() and .set_bias() callbacks
should be implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/19b3e0773fbb36c015a43db683f79e75b0fec3ee.1640270559.git.geert+renesas@glider.be
Currently rcar_pin_to_bias_reg() takes a struct sh_pfc pointer, which is
only available after the pin control driver has been initialized,
thus preventing the checker from calling this function for validating
consistency of the pin control tables.
Fix this by replacing the parameter by a struct sh_pfc_soc_info pointer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/3065a12dde606bacec9e5f14f10cabeaae75e265.1640270559.git.geert+renesas@glider.be
All implementations of the .pin_to_portcr() method implement the same
conversion from Port Control Register offset to virtual address. Factor
it out into the two callers.
Remove the pfc parameter, as it is no longer used.
Note that the failure handling in r8a7740_pin_to_portcr() is pro forma,
as the function is never called with an invalid pin number.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/a485d4986a17259256988eb14e3a4c2b8d61c303.1640270559.git.geert+renesas@glider.be
The pfc parameter of the .pin_to_pocctrl() method was never used.
It is a relic of the old I/O voltage handling before commit
8775306dcf ("pinctrl: sh-pfc: refactor voltage setting").
Remove the parameter, as it prevents the checker from calling this
function for validating consistency of the pin control tables.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/822133086f32618c7fc920123c6a96f5d4ea7ad6.1640270559.git.geert+renesas@glider.be
Pin groups mmc_data[14] are subsets of mmc_data8.
Treat mmc_data8_b the same for consistency. Note that there is no need
to define 1-bit and 4-bit wide subsets for the b-variant, as they're
identical to the normal variants.
This reduces kernel size by 40 bytes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/be1f11c87e51224e043291f4d8e28b620811ac76.1640269757.git.geert+renesas@glider.be
The VIN_DATA_PIN_GROUP() macro and vin_data{12,16,} unions are used to
define multiple VIN data groups with different numbers of lanes, while
referring to a single array of data pins, thus saving memory.
However, the same feature would be useful for other resizable buses,
like MMC, SDHI, QSPI, LCD, BSC, ...
Rework the mechanism for generic use:
- Use the new SH_PFC_PIN_GROUP_SUBSET() helper to remove the need for
bus-specific unions,
- Rename VIN_DATA_PIN_GROUP() to BUS_DATA_PIN_GROUP(),
- Rename the macro parameters to better reflect their purposes,
- Move the macro up, where it belongs.
Update all individual pin control drivers for the above changes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/cccfcfd01eb8ab7a587b084c4ddbf97293bd7291.1640269757.git.geert+renesas@glider.be
Reformat all macros that define structure initializers, to visually
resemble structure definitions:
- Move the opening curly brace to the previous line,
- Move the closing curly brace to the first position,
- Reduce indentation of the block to a single TAB, decreasing the need
for line breaks,
- Align backslashes for line continuation to the last TAB block where
possible,
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/03a1eed3c4f57d7b14ef53ab49e04de10d0e383c.1640269757.git.geert+renesas@glider.be
Some instances of struct sh_pfc_soc_operations are called
"<soc>_pfc_ops", others are called "<soc>_pinmux_ops" or just
"pinmux_ops". Settle on the first variant, to avoid confusion with
"struct pinmux_ops" in the pinctrl core, and to increase consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2ab33ad1d6a20a57d16922678b78810fa55b7fc0.1640269757.git.geert+renesas@glider.be
The second video-in channel on RZ/G1C has only 12 data lanes, but the
pin control driver uses the vin_data union, which is meant for 24 data
lanes, thus wasting space.
Fix this by using the vin_data12 union instead.
This reduces kernel size by 96 bytes.
Fixes: 50f3f2d73e ("pinctrl: sh-pfc: Reduce kernel size for narrow VIN channels")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/52716fa89139f6f92592633edb52804d4c5e18f0.1640269757.git.geert+renesas@glider.be
Update rzg2l_gpio_register() to use driver data for chip->names
and check for gpio-range. This allows reusing the driver for
SoC's with different port pin definitions(eg:- RZ/G2UL SoC has
fewer ports compared to RZ/G2L and port pin definitions are
different).
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20220206194614.13209-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
For Renesas PFCs not setting .strict, we can snoop GPIOs which are
already muxed to some other function. To actually make use of that, we
shouldn't mux them back to GPIO if they have been already muxed to
something.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20211210113226.40111-1-wsa+renesas@sang-engineering.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Align comments in the R-Car V3U pin control driver.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYbxj9gAKCRCKwlD9ZEnx
cMhKAQD+V66ADB9lwaSKLNwxK5TA8v6hpJTOP7FXFcbhpzafyQD/d9QETuTFehxZ
PyNfggjhzv6yi0qdIOvbv+t4lcf/4wo=
=WvSa
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.17-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.17 (take two)
- Align comments in the R-Car V3U pin control driver.
GPIO library does copy the of_node from the parent device of
the GPIO chip, there is no need to repeat this in the individual
drivers. Remove these assignment all at once.
For the details one may look into the of_gpio_dev_init() implementation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20211214125855.33207-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no need to acquire the spinlock when reading from a pin
controller register:
1. Reading a single MMIO register is an atomic operation,
2. While sh_pfc_phys_to_virt() inside sh_pfc_read() has to traverse
all mapped windows to find the appropriate virtual address, this
does not need any locking, as the window mappings are never
changed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/2008ca99f0079fd5d4e640b7ef78710c98cc9f77.1637143108.git.geert+renesas@glider.be
RZ/G2L supports two groups of pins Group-A and Group-B. For Group-A
pins drive-strength can be configured and for Group-B output-impedance
can be configured.
This patch splits PIN_CFG_IOLH macro to PIN_CFG_IOLH_A/B and adds
support to get/set drive-strength and output-impedance-ohms for the
supported pins.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110224622.16022-7-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be checked. In addition, sh_pfc_check_bias_reg()
does not handle such entries.
Fix this by treating pinmux_bias_reg.puen and pinmux_bias_reg.pud the
same.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/29526d06fa223cffd785cdb264b756a202b11cea.1633615652.git.geert+renesas@glider.be
The GENMASK(h, l) macro creates a contiguous bitmask starting at bit
position @l and ending at position @h, inclusive.
This did not trigger any error checks, as the individual register fields
cover at most 3 of the 4 available bits.
Fixes: 08df16e07a ("pinctrl: sh-pfc: checker: Add drive strength register checks")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/8f82d6147fbe3367d4c83962480e97f58d9c96a2.1633615652.git.geert+renesas@glider.be
If some bits in a pin Pull-Up control register (PUPR) control pin
pull-down instead of pin pull-up, there are two pinmux_bias_reg entries:
a first one with the puen field filled in, listing pins with pull-up
functionality, and a second one with the pud field filled in, listing
pins with pull-down functionality. On encountering the second entry,
where puen is NULL, the for-loop terminates early, causing the remaining
bias registers not to be saved/restored during PSCI system suspend.
Fortunately this does not trigger on any supported system yet, as PSCI
is only used on R-Car Gen3 and RZ/G2 systems, which all have separate
pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD) registers.
Avoid this ever becoming a problem by treating pinmux_bias_reg.puen and
pinmux_bias_reg.pud the same. Note that a register controlling both
pull-up and pull-down pins would be saved and restored twice, which is
harmless.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/59d2fbddff685b6a7a82ff17d2b37633e30e8860.1633615652.git.geert+renesas@glider.be
Remove the duplicate port register 22h and replace it with missing port
register 21h.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210922074140.22178-1-biju.das.jz@bp.renesas.com
Fixes: c4c4637eb5 ("pinctrl: renesas: Add RZ/G2L pin and gpio controller driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Global static variables don't need to be initialized to 0, because the
compiler will initialize them.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20210906134040.96642-1-wangborong@cdjrlc.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add support for pin and gpio controller driver for RZ/G2L SoC.
Based on a patch in the BSP by Hien Huynh <hien.huynh.px@renesas.com>.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20210727112328.18809-3-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As R-Car H3 ES1.x (R8A77950) and R-Car ES2.0+ (R8A77951) use the same
compatible value, the pin control driver relies on soc_device_match()
with soc_id = "r8a7795" and the (non)matching of revision = "ES1.*" to
match with and distinguish between the two SoC variants. The
corresponding entries in the normal of_match_table are present only to
make the optional sanity checks work.
The R-Car H3e-2G (R8A779M1) SoC is a different grading of the R-Car H3
ES3.0 (R8A77951) SoC. It uses the same compatible values for individual
devices, but has an additional compatible value for the root node.
When running on an R-Car H3e-2G SoC, soc_device_match() with soc_id =
"r8a7795" does not return a match. Hence the pin control driver falls
back to the normal of_match_table, and, as the R8A77950 entry is listed
first, incorrectly uses the sub-driver for R-Car H3 ES1.x.
Fix this by moving the entry for R8A77951 before the entry for R8A77950.
Simplify sh_pfc_quirk_match() to only handle R-Car H3 ES1,x, as R-Car H3
ES2.0+ can now be matched using the normal of_match_table as well.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/6cdc5bfa424461105779b56f455387e03560cf66.1626707688.git.geert+renesas@glider.be
Implement support for pull-up (most pins, excl. DU_DOTCLKIN0) and
pull-down (most pins, excl. JTAG) handling for the R-Car D3 SoC, using
some parts from the common R-Car bias handling, which requires making
rcar_pin_to_bias_reg() public.
R-Car D3 needs special handling for the NFRE# (GP_3_0) and NFWE#
(GP_3_1) pins. Unlike all other pins, they are controlled by different
bits in the LSI pin pull-up/down control register (PUD2) than in the LSI
pin pull-enable register (PUEN2).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/04aad2b0bf82a32fb08e5e21e4ac1fb03452724f.1625064076.git.geert+renesas@glider.be
When disabling pin bias, there is no need to touch the LSI pin
pull-up/down control register (PUDn), which selects between pull-up and
pull-down. Just disabling the pull-up/down function through the LSI pin
pull-enable register (PUENn) is sufficient.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/071ec644de2555da593a4531ef5d3e4d79cf997d.1625064076.git.geert+renesas@glider.be
Implement support for pull-up (most pins, excl. DU_DOTCLKIN and EXTALR)
and pull-down (most pins, excl. JTAG) handling for the R-Car V3M SoC,
using the common R-Car bias handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/bcfad447624d874258a45a92554574b8fe9f712f.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car E2 and RZ/G1E SoCs, using the common R-Car bias
handling.
Note that on RZ/G1E, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/f78da2ba937ce98ae9196f4ee54149a5214fd545.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (EDBGREQ)
handling for the R-Car V2H SoC, using the common R-Car bias handling.
Note that the R-Car V2H Hardware User's Manual Rev. 1.00 says that
the LSI Pin Pull-Up Control Register 11 (PUPR11) controls pull-ups for
the {SCK,WS,SDATA}[01] pins. These are assumed to be typos, as R-Car
V2H has only Serial Sound Interface channels 3 and 4.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/48d2abdd63ee43ed99cb32ed4a5f4d76ba563162.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car H2 and RZ/G1H SoCs, using the common R-Car bias
handling.
Note that on RZ/G1H, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/dde6e0b36a4e4494039a3466df208b5ec5c594ee.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for the RZ/G1C SoC, using the common R-Car bias handling.
Note that on RZ/G1C, the "ASEBRK#/ACK" pin is called "ACK", but the code
doesn't handle that naming difference. Hence users should use the R-Car
naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/18c8ebf9fa9e239253a723857e9dffeec775db7e.1619785375.git.geert+renesas@glider.be
Change whitespace in the pin control drivers for R-Car H3 ES2.0+, R-Car
M3-W/M3-W+, and R-Car M3-N, to reduce the differences among these very
similar drivers.
These changes have no functional impact.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/527b45ebfc664a80e41cb0136677db7260e11437.1619785375.git.geert+renesas@glider.be
R-Car Gen3 Hardware Manual Errata for Rev. 0.52 of Nov 30, 2016, added
the configuration bit for bias pull-down control for the PRESET# pin on
R-Car M3-W. Add driver support for controlling pull-down on this pin.
Fixes: 2d40bd2427 ("pinctrl: sh-pfc: r8a7796: Add bias pinconf support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/c479de5b3f235c2f7d5faea9e7e08e6fccb135df.1619785375.git.geert+renesas@glider.be
Implement support for pull-up (most pins) and pull-down (ASEBRK#/ACK)
handling for R-Car M2-W and M2-N, and RZ/G1M and RZ/G1N SoCs, using the
common R-Car bias handling.
Note that on RZ/G1 SoCs, the "ASEBRK#/ACK" pin is called "ACK", but the
code doesn't handle that naming difference. Hence users should use the
R-Car naming in DTS files.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-7-geert+renesas@glider.be
Currently, the common R-Car bias handling supports pin controllers with
either:
1. Separate pin Pull-Enable (PUEN) and pin Pull-Up/Down control (PUD)
registers, for controlling both pin pull-up and pin pull-down,
2. A single pin Pull-Up control register (PUPR), for controlling pin
pull-up.
Add support for a variant of #2, where some bits in the single pin
Pull-Up control register (PUPR) control pin pull-down instead of pin
pull-up. This is the case for the "ASEBRK#/ACK" pin on R-Car M2-W,
M2-N, and E2, and the "ACK" pin on RZ/G1M, RZ/G1N, RZ/G1E, and RZ/G1C.
To describe such a register, SoC-specific drivers need to provide two
instances of pinmux_bias_reg: a first one with the puen field filled in,
listing pins with pull-up functionality, and a second one with the pud
field filled in, listing pins with pull-down functionality.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-6-geert+renesas@glider.be
Add PORT_GP_CFG_7() and PORT_GP_7() helper macros, to be used by the
r8a7791 subdriver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-5-geert+renesas@glider.be
The pin control sub-drivers for SH/R-Mobile SoCs contain almost
identical bias handling. The only SoC-specific part is the mapping from
pin numbers to PORTnCR registers.
Reduce code duplication by factoring out the bias handling to the common
pinctrl.c code. Use a callback to handle the pin/register mapping.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-4-geert+renesas@glider.be
The Renesas Pin Function Controller driver uses two header files:
- sh_pfc.h, for use by both core code and SoC-specific drivers,
- core.h, for internal use by the core code only.
Hence move the R-Car bias helper declarations from core.h to sh_pfc.h,
and drop the inclusion of core.h from SoC-specific drivers that no
longer need it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-3-geert+renesas@glider.be
Now all R-Car pin control drivers have been converted to the common
R-Car bias handling, sh_pfc_pin_to_bias_reg() is only called from a
single place. Move it from core.c to pinctrl.c, make it static, and
rename it to rcar_pin_to_bias_reg(), as it is specific to R-Car SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210303132619.3938128-2-geert+renesas@glider.be
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCYAFgRQAKCRCKwlD9ZEnx
cEWIAP40TrUerqfnQgJ7iNYLh9WfSk48w9Gxzm92E7FanXaJBAD/dmkieXwQBBig
zKNuoWL2ZlK7O5MMkzpNnhLNS95SEQs=
=vIxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.12-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.12
- Restrict debug runtime-checks to Renesas platforms,
- Initial support for the R-Car V3U SoC.
Add pins, groups and functions for the 16-Bit Timer Pulse Unit outputs
on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-13-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and function for the Interrupt Controller for External
Devices (INTC-EX) on the R-Car R8A779A0 (V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20210112165929.31002-7-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch adds HSCIF0-3 pins, groups and functions to the R8A779A0
(V3U) SoC.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20210112165929.31002-6-uli+renesas@fpond.eu
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Geert Uytterhoeven