The n30_init_irq() call is simply a call to s3c24xx_init_irq, so
just remove it and update the machine definitions to call the IRQ
initialision call directly.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
There is bug in USB setup code for Acer n35 (it is related directly to s3c2410,
see doc). We want suspend host port (is not connected) but device port should be
active.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
All code already present for Acer n35 is useless unless MACH_N35 is defined.
Signed-off-by: Jiri Pinkava <jiri.pinkava@vscht.cz>
[ben-linux@fluff.org: minor edit of subject]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the old S3C2410_GPJ as we will be moving to the new gpiolib
based driver code and these numbers will become invalid.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change s3c2410_gpio_setpin() and s3c2410_gpio_pullup() to use
the new s3c_ gpio configuration calls until all their users
are converted.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the last s3c2410_gpio_pullup() users in arch/arm/mach-s3c2410
Note, since mach-h1940.c is setting output and a pull-up, the call
has vbeen chanerd to S3C_GPIO_PULL_NONE instead of S3C_GPIO_PULL_UP.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the mach-mini2440 to using the gpiolib API for GPIOS it
directly uses, and s3c_gpio calls for configuration.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary 1,2 and 4 bit configuration read calls for the new
gpio code to allow removal of the old s3c24xx gpio code.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove s3c2410_gpio_getirq() as the only users is the pm code, and it
can be replicated by using gpio_to_irq().
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Remove the implementation of s3c2410_gpio_setcfg() as it should now be
functionally equivalent to s3c_gpio_cfgpin(), and add a wrapper for those
drivers that are still using this call.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The s3c_gpio_cfgpin() call should be functionally equivalent, so replace
the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin
to allow moving away from a fixed GPIO number to register address mapping
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.
sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.
sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Change mach-jive to use gpiolib for the GPIO lines that are directly
manipulated by it.
Note, we ignore any errors from gpio_request(), unlikely to see any.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the GPIO banks that are used on the S3C2443 and above to the
list of available GPIOS.
Currently we do not have any limit on the SoC GPIO, so these are
being registered whether the SoC has them or not. It is currently
up to the user not to try and use them.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add the necessary gpio configuration helper for the devices which
have a single-bit pull-up resistor disabled.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add support for s3c_gpio_setcfg() and s3c_gpio_setpull() implementations
to get ready for removal of the specific code being used by s3c24xx.
Also rename the s3c_gpio_setcfg_s3c24xx_banka to s3c_gpio_setcfg_s3c24xx_a
as seen in the header file to correct a build warning.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The s3c24xx_mci_set_platdata() is init time only, so should
be marked as __init
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
[ben-linux@fluff.org: update description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Setting s3c2410fb_mach_info displays field with a struct marked as __initdata
means it won't be available later for ioctls like FBIOPUT_VSCREENINFO and they
will fail. Copying in s3c24xx_fb_set_platdata() is fixing this issue.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The touchscreen is using the adc device so it needs to be in the device
list
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
MUSB can supply upto 500mA such as, AM3517 and OMAP3EVM Rev >=E and thus
the 'power' field has to hold values above 255.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 6061/1: PL061 GPIO: Bug fix - setting gpio for HIGH_LEVEL interrupt is not working.
ARM: 5957/1: ARM: RealView SD/MMC Card detection and write-protect using GPIOLIB
ARM: 6030/1: KS8695: enable console
ARM: 6060/1: PL061 GPIO: Setting gpio val after changing direction to OUT.
ARM: 6059/1: PL061 GPIO: Changing *_irq_chip_data with *_irq_data for real irqs.
ARM: 6023/1: update bcmring_defconfig to latest version and fix build error
ARM: fix build error in arch/arm/kernel/process.c
The switch to using GPIOLIB broke the sd/mmc card detection on the
RealView development boards if GPIO_PL061 was not selected.
This patch selects GPIO_PL061 if GPIOLIB is selected.
The sense of the return value from mmc_status has also changed
and is corrected.
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
They are not needed and add over 512 bytes to kernel data.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Old code from original patch contains beagle board pins that are
not available on the Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change position of calling serial and ethernet initialization.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Devkit8000 uses the CUS package for OMAP3530.
This patch adds missing package selection for CUS and enables
CONFIG_MUX.
Replace whitespace with tab in Kconfig.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/configs/n8x0_defconfig:1061:warning: override: reassigning to
symbol NILFS2_FS
Signed-off-by: Francisco Alecrim <francisco.alecrim@openbossa.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Corrected type of flash in output (OneNAND => NOR).
Removed whitespace after newline in output.
Removed double whitespace in output.
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Modern udev will not work with the CONFIG_SYSFS_DEPRECATED*=y options and
it seems also that the Maemo release works without when testing with the
Maemo 2.6.28 kernel.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Phonet is enabled by the commit bce54fed94
and this duplicate gives a warning when doing make rx51_defconfig.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If gpmc_t isn't given, we don't need to set timing for gpmc, or it will cause
a Oops.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The initialize of i2c subsystem will set pinmux, so it should be done
after the initialize of mux subsystem initialization.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
INT_34XX_BENCH_MPU_EMUL was defined twice, another is at Line 312.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_MTD_NAND_OMAP2 is not enabled, there will be a compile error,
"gpmc_nand_init() is not defined". Add a inline noop function to fix it.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Change the name for the spi instances on omap44xx_clks to match
the names omap2 spi driver gives:
omap-mcspi.1 -> omap2_mcspi.1
omap-mcspi.2 -> omap2_mcspi.2
omap-mcspi.3 -> omap2_mcspi.3
omap-mcspi.4 -> omap2_mcspi.4
Signed-off-by: Abraham Arce <x0066660@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable the nonexistent ehci port on Devkit8000.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the base address of CONTROL register on OMAP4430SDP.
The control base is used by peripherals like MMC1 for PBIAS configuration.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
IGEP v2 uses EHCI port 1 instead of EHCI port 2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning: 'return' with a value, in function returning void
in n8x0_mmc_init. Also fix a search and replace typo.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The value to check is 7 for V6 instead. The code has been
working as it falls through to 24xx code if the other checks
fail.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register DMA4_CDAC needs to be initialized to zero
before starting DMA transfer.
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Govindraj R <govindraj.raja@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Reported-by:S, Venkatraman <svenkatr@ti.com>
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since IRQ_TYPE_EDGE_BOTH is defined as (IRQ_TYPE_EDGE_FALLING |
IRQ_TYPE_EDGE_RISING), testing against it with a bitwise AND also matches
both single-edge cases in addition to the intended both edges case. Fix it,
replacing with a more accurate expression.
Created and tested againts linux-2.6.34-rc3.
Applicable to 2.6.33-stable as well.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When the 32k sync timer is used for sched_clock(), it should count
time from the kernel boot (clocksource init) instead of the last HW
reset. Otherwise printk.time values will jump suddenly during the boot:
[ 0.000000] calling omap2_clk_arch_init+0x0/0x138 @ 1
[ 0.000000] initcall omap2_clk_arch_init+0x0/0x138 returned -22 after 0 usecs
[ 0.000000] initcall omap2_clk_arch_init+0x0/0x138 returned with error code -22
[ 0.000000] calling omap_init_clocksource_32k+0x0/0x98 @ 1
[ 508.697937] initcall omap_init_clocksource_32k+0x0/0x98 returned 0 after 0 usecs
[ 508.697967] calling omap_init_devices+0x0/0x38 @ 1
[ 508.698425] initcall omap_init_devices+0x0/0x38 returned 0 after 0 usecs
This will confuse tools such as scripts/bootgraph.pl.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
update bcmring_defconfig to the latest kernel version, this will fix the
KAutobuild error.
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
/tmp/ccJ3ssZW.s: Assembler messages:
/tmp/ccJ3ssZW.s:1952: Error: can't resolve `.text' {.text section} - `.LFB1077'
This is caused because:
.section .data
.section .text
.section .text
.previous
does not return us to the .text section, but the .data section; this
makes use of .previous dangerous if the ordering of previous sections
is not known.
Fix up the other users of .previous; .pushsection and .popsection are
a safer pairing to use than .section and .previous.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cosmetic change to mach-at91 Makefile: remove two blanks introduced
by earlier patches.
Signed-off-by: Ernst Schwab <eschwab@online.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When crash happens in interrupt context there is no userspace context.
We always use current->active_mm in those cases.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Imre Deak <imre.deak@nokia.com>
Signal handlers can use floating point, so prevent them to corrupt
the main thread's VFP context. So far there were two signal stack
frame formats defined based on the VFP implementation, but the user
struct used for ptrace covers all posibilities, so use it for the
signal stack too.
Introduce also a new user struct for VFP exception registers. In
this too fields not relevant to the current VFP architecture are
ignored.
Support to save / restore the exception registers was added by
Will Deacon.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Imre Deak <imre.deak@nokia.com>
Recently the UP versions of these functions were refactored and as
a side effect it became possible to call them for the current thread.
This isn't true for the SMP versions however, so fix this up.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The VIVT cache of a highmem page is always flushed before the page
is unmapped. This cache flush is explicit through flush_cache_kmaps()
in flush_all_zero_pkmaps(), or through __cpuc_flush_dcache_area() in
kunmap_atomic(). There is also an implicit flush of those highmem pages
that were part of a process that just terminated making those pages free
as the whole VIVT cache has to be flushed on every task switch. Hence
unmapped highmem pages need no cache maintenance in that case.
However unmapped pages may still be cached with a VIPT cache because the
cache is tagged with physical addresses. There is no need for a whole
cache flush during task switching for that reason, and despite the
explicit cache flushes in flush_all_zero_pkmaps() and kunmap_atomic(),
some highmem pages that were mapped in user space end up still cached
even when they become unmapped.
So, we do have to perform cache maintenance on those unmapped highmem
pages in the context of DMA when using a VIPT cache. Unfortunately,
it is not possible to perform that cache maintenance using physical
addresses as all the L1 cache maintenance coprocessor functions accept
virtual addresses only. Therefore we have no choice but to set up a
temporary virtual mapping for that purpose.
And of course the explicit cache flushing when unmapping a highmem page
on a system with a VIPT cache now can go, which should increase
performance.
While at it, because the code in __flush_dcache_page() has to be modified
anyway, let's also make sure the mapped highmem pages are pinned with
kmap_high_get() for the duration of the cache maintenance operation.
Because kunmap() does unmap highmem pages lazily, it was reported by
Gary King <GKing@nvidia.com> that those pages ended up being unmapped
during cache maintenance on SMP causing segmentation faults.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Julien Langer <julien.langer@gmail.com>
AT91: when turning off the PLLs during suspend, don't wait for the lock
flag to be set. Previously the code would always run into the loop
limitation of 1000 iterations because the flag is never set when turning
the PLLs off.
Comments from Anders Larsen:
(in http://marc.info/?l=linux-kernel&m=127058929724193&w=2)
Signed-off-by: Julien Langer <julien.langer@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm: (21 commits)
ARM: Fix ioremap_cached()/ioremap_wc() for SMP platforms
ARM: 6043/1: AT91 slow-clock resume: Don't wait for a disabled PLL to lock
ARM: 6031/1: fix Thumb-2 decompressor
ARM: 6029/1: ep93xx: gpio.c: local functions should be static
ARM: 6028/1: ARM: add MAINTAINERS for U300
ARM: 6024/1: bcmring: fix missing down on semaphore in dma.c
MXC: mach_armadillo5x0: Add USB Host support.
ARM mach-mx3: duplicated include
ARM mach-mx3: duplicated include
imx31: add watchdog device on litekit board.
imx3: Add watchdog platform device support
MXC: mach-mx31_3ds: add support for freescale mc13783 power management device.
MXC: mach-mx31_3ds: Add SPI1 device support.
MXC: mach-mx31_3ds: Add support for on board NAND Flash.
MXC: mach-mx31_3ds: Update variable names over recent mach name modification.
imx31: fix parent clock for rtc
i.MX51: remove NFC AXI static mapping
i.MX51: determine silicon revision dynamically
i.MX51: map TZIC dynamically
i.MX51: Use correct clock for gpt
...
Write combining/cached device mappings are not setting the shared bit,
which could potentially cause problems on SMP systems since the cache
lines won't participate in the cache coherency protocol.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
at91 slow-clock resume: Don't wait for a disabled PLL to lock.
We run into this problem with the PLLB on the at91: ohci-at91 disables
the PLLB when going to suspend. The slowclock code however tries to do
the same: It saves the PLLB register value and when restoring the value
during resume, it waits for the PLLB to lock again. However the PLL will
never lock and the loop would run into its timeout because the slowclock
code just stored and restored an empty register.
This fixes the problem by only restoring PLLA/PLLB when they were enabled
at suspend time.
Cc: Andrew Victor <avictor.za@gmail.com>
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
98e12b5a6e ("ARM: Fix decompressor's kernel size estimation for
ROM=y") broke the Thumb-2 decompressor because it added an entry in the
LC0 table but didn't adjust the offset the Thumb-2 code uses to load the
SP from that table. Fix it.
Cc: stable <stable@kernel.org>
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The functions ep93xx_gpio_update_int_params and ep93xx_gpio_int_mask
are not exported and should be static. This was overlooked when
moving the code from core.c.
Also, change a comment to better indicate what the code is for.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added missing down on the memMap->lock semaphore. Also fixed a return
statement so that we always exit with an up (i.e. early exit via return
is not allowed)
Signed-off-by: Leo Hao Chen <leochen@broadcom.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This hushes the following warning:
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: ‘struct platform_device’
declared inside parameter list
arch/arm/mach-davinci/include/mach/da8xx.h:104: warning: its scope is only this
definition or declaration, which is probably not what you want
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
IRQ 29 has two possible interrupts DDRINT and RTC, but having both in
the default priority table is confusing (and triggers a warning from
sparse.)
This patch removes the lower priority DDRINT from the default priority
table leaving the RTC setting as the default.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch fixes an issue where a DMA channel can erroneously process an
event generated by a previous transfer. A failure case is where DMA is
being used for SPI transmit and receive channels on OMAP L138. In this
case there is a single bit that controls all event generation from the
SPI peripheral. Therefore it is possible that between when edma_stop()
has been called for the transmit channel on a previous transfer and
edma_start() is called for the transmit channel on a subsequent transfer,
that a transmit event has been generated.
The fix is to clear events in edma_start(). This prevents false events
from being processed when events are enabled for that channel.
Signed-off-by: Brian Niebuhr <bniebuhr@efjohnson.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The da8xx/omap-l1 boards refuse to build when CONFIG_DAVINCI_MUX is undefined
because arch/arm/mach-davinci/mux.c:da8xx_pinmux_setup() is not defined.
This patch fixes this issue. This is build tested with davinci_all_defconfig
and da8xx_omapl_defconfig and boot tested on DA830 EVM.
Reported-by: Shanmuga Sundaram Mahendran <shanmuga@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On da830, when the same timer is used for clocksource and clockevent,
the timer can be started before the clockevent is
registered/initialzed. This creates a window where a timer
interrupt might fire before the clockevent handler has been
setup and causes a crash.
This patch moves the actual enable/start of the timer after
the clockevent has ben registered.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The enable bit for dpll4_m4x2 clock should be OMAP3430_PWRDN_DSS1_SHIFT.
The code erroneously uses OMAP3430_PWRDN_CAM_SHIFT which is meant for
dpll4_m5x2 clock.
This came into notice during a recent review of the clock tree.
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch fixes usage of bitwise OR in if conditions, and instead
uses logical OR.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Cc: Abhijit Pagare <abhijitpagare@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch corrects the width of sysc_flags in hwmod sysconfig structure
where the values to be stored to this variable exceed the current
field width.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: edited to apply; rearranged structure members to pack]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This patch adds check for presence of clockdomain structure in the API
omap_hwmod_get_pwrdm before trying to access the powerdomain structure.
This will prevent unnecessary crashing of the system in case of a
clock node with out an associated clockdomain.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
This add USB Host capability. The Armadillo 500 board is supplied
with two USB Host connectors driven by the USB OTG and USB Host 2
ports, through two NXP isp 1504 transceivers.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch/arm/mach-mx3/mx31lite-db.c: linux/platform_device.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
arch/arm/mach-mx3/mach-pcm037.c: linux/fsl_devices.h is included more than once.
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch adds support for build-in watchdog device found on
Freescale imx31 and imx35 SoCs.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
When compiling the kernel to Thumb-2, using a 16-bit NOP in the
memmove() implementation causes the preceding ADD PC instruction to
branch incorrectly in the middle of a 32-bit LDR or STR instruction. The
memmove() code is now similar to the memcpy() template.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Current implementation of jprobes allocates empty pt_regs from the
stack which is then passed to kprobe_handler() and eventually to
singlestep(). Now when instruction being simulated is STMFD (like
in normal function prologues without CONFIG_FRAME_POINTER), stores
using SP actually write over top of the fabricated pt_regs
structure.
This can be reproduced for example by using LKDTM module:
# modprobe lkdtm
# mount -t debugfs none /sys/kernel/debug
# echo PANIC > /sys/kernel/debug/provoke-crash/INT_HW_IRQ_EN
after this, it fails with corrupted registers (before the requested crash would occur):
lkdtm: Crash point INT_HW_IRQ_EN of type PANIC hit, trigger in 9 rounds
lkdtm: Crash point INT_HW_IRQ_EN of type PANIC hit, trigger in 8 rounds
Internal error: Oops - undefined instruction: 0 [#1]
last sysfs file: /sys/devices/platform/serial8250.0/sleep_timeout
Modules linked in: lkdtm
CPU: 0 Not tainted (2.6.34-rc2 #69)
PC is at irq_desc+0x1638/0xeeb0
LR is at 0x25
pc : [<c050b428>] lr : [<00000025>] psr: c80a0013
sp : ce94bd60 ip : c050b3e8 fp : a0000013
r10: c0aa453c r9 : cf5d4000 r8 : ce9a1822
r7 : c050b424 r6 : 00000025 r5 : c039d8f8 r4 : c050b3e8
r3 : 00000001 r2 : cf4d0440 r1 : c039d8f8 r0 : 00000020
Flags: NZcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 10c5387d Table: 8e804019 DAC: 00000015
Process sh (pid: 496, stack limit = 0xce94a2e8)
Stack: (0xce94bd60 to 0xce94c000)
[...]
Code: 000002cd 00000000 00000000 00000001 (dead4ead)
---[ end trace 2b46d5f2b682f370 ]---
Kernel panic - not syncing: Fatal exception in interrupt
This patch allocates enough space (2 * sizeof(struct pt_regs)) from
the stack to prevent such corruption.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
clkdev.h is using struct device *. Due to this compilation
warning is comming. Removing this warning.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
irq.h is using struct pt_regs *. Due to this compilation
warning is comming. Removing this warning by adding declaration
of struct pt_regs.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A CPU has VFPv3 hardware if the FPSID[19:16] bits are 2 or more.
Currently Linux was only checking for 3 or more.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mandatory barriers (mb, rmb, wmb) are used even on uniprocessor
systems for things like ordering Normal Non-cacheable memory accesses
with DMA transfer (via Device memory writes). The current implementation
uses dmb() for mb() and friends but this is not sufficient. The DMB only
ensures the relative ordering of the observability of accesses by other
processors or devices acting as masters. In case of DMA transfers
started by writes to device memory, the relative ordering is not ensured
because accesses to slave ports of a device are not considered
observable by the DMB definition.
A DSB is required for the data to reach the main memory (even if mapped
as Normal Non-cacheable) before the device receives the notification to
begin the transfer. Furthermore, some L2 cache controllers (like L2x0 or
PL310) buffer stores to Normal Non-cacheable memory and this would need
to be drained with the outer_sync() function call.
The patch also allows platforms to define their own mandatory barriers
implementation by selecting CONFIG_ARCH_HAS_BARRIERS and providing a
mach/barriers.h file.
Note that the SMP barriers are unchanged (being DMBs as before) since
they are only guaranteed to work with Normal Cacheable memory.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The L2x0 cache controllers need to explicitly drain their write buffer
even for Normal Noncacheable memory accesses.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces the outer_cache_fns.sync function pointer together
with the OUTER_CACHE_SYNC config option that can be used to drain the
write buffer of the outer cache.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To avoid #include collisions with subsequent patches in the series, this
patch moves the outer_cache definitions to a separate asm/outercache.h
file.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Power Gates must to be always enabled.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Since the using of Bad Block Table is not constantly a good behave
I had made it configurable.
Signed-off-by: Alberto Panizzo <maramaopercheseimorto@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
According to imx31 reference manual the signal from external low
frequency clock is sent to RTC clock.
The patch makes redundant the previously defined mxc_rtc clock.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
"Input: add KEY_WPS_BUTTON definition" introduced
a generic keycode for WPS input events.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Commit "Input: add KEY_WPS_BUTTON definition"
added a generic keycode for WPS button.
Let's use it, instead of "F1" mapping.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
This fixes a warning when booting 2.6.34-rc2:
[ 26.619814] ------------[ cut here ]------------
[ 26.624604] WARNING: at fs/proc/generic.c:316 __xlate_proc_name+0xac/0xc0()
[ 26.631555] name 'on/off button'
[ 26.634753] Modules linked in:
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The function locomo_m62332_senddata sends a three byte i2c message to
a M62332 DAC. This entire function is guarded with a spin_lock_irqsave
at the start of the function and a spin_unlock_irqrestore at the end.
As each byte is transferred, the i2c ACK from the DAC is checked.
Currently, if the ACK is missing the function simply returns without
the unlock. It also leaves the i2c bus in an invalid state since the
last byte transferred did not have a "stop" condition and leave the
bus idle.
Fix this by adding an exit path using goto.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The locomo spi registers are all defined in locomo.h as offsets
from the first spi register LOCOMO_SPI (0x60), which is itself
an offset from the locomo base address. To correctly access
these registers LOCOMO_SPI must always be included in the
address calculation.
There are two places in locomo.c where this is not done. The
first one, in locomo_suspend, actually results in a write to
LOCOMO_ST instead of LOCOMO_SPICT. The second is in __locomo_probe
and results in a write to LOCOMO_MCSX2 instead of LOCOMO_SPIIE.
Fix these by including LOCOMO_SPI in the calculation.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
sharpsl_pm.c actually depends on max1111 driver being built-in when
not using legacy ssp code.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Reported-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Due to commit:
5de813b ARM: Eliminate decompressor -Dstatic= PIC hack
The data section will be discarded for the decompressor, thus move the
static variables into BSS section by initializing them at run time.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
One to many close parens.
In file included from arch/arm/include/asm/page.h:202,
from include/linux/mm_types.h:15,
from include/linux/sched.h:63,
from arch/arm/kernel/asm-offsets.c:13:
arch/arm/include/asm/memory.h: In function 'virt_to_bus':
arch/arm/include/asm/memory.h:214: error: expected ';' before ')' token
arch/arm/include/asm/memory.h:214: error: expected statement before ')' token
arch/arm/include/asm/memory.h: In function 'bus_to_virt':
arch/arm/include/asm/memory.h:219: error: expected ';' before ')' token
arch/arm/include/asm/memory.h:219: error: expected statement before ')' token
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This area contains the Nand Flash controller registers. There
is no need to map them statically as the Nand driver uses ioremap().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Freescale redboot passes the silicon revision via
ATAG_REVISION. Remove this bootloader dependency by
doing the same as redboot does in the Kernel.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This looks cleaner and allows us to call mx51_revision
later when we can use ioremap to determine the silicon
revision dynamically.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
ARM/OMAP: Remove the +x bit from a couple of source files
omap: McBSP: Drop unnecessary status/error bit clearing on reg_cacheretrieved register values
OMAP4: fix temporary hacks that break multi-omap PM
OMAP2: cpu_is_omap2*: fix compile-time removal of unused code
omap3: pandora: add missing i2c3 board_info
omap: mach-omap2/io.c: fix function declarations
omap: Fix gpio_resume_after_retention
omap3: Fix support for the LEDs connected to GPIO outputs on IGEP v2board
omap: Checkpatch cleanup for blizzard.h
omap: pass the reboot command to the boot loader
omap2/3/4: mailbox: remove compiler warning
OMAP2: serial.c: Fix number of uarts in early_init
omap: Enable PM_RUNTIME in defconfigs to avoid USB compile errors
omap2: Update n8x0 defconfig to test multi-omap and DMA api changes
omap2: add USB initialization for tusb6010
omap4: Fix build break by moving omap_smc1 into a separate .S
omap2/3/4: ehci: avoid compiler error with touchbook
omap3: Fix compile for Touch Book early_param
Commit 4e6d488af3 either missed out the
following machine files or somehow managed to clash between merges.
Fixup the three files missing the second parameter to addruart macro
to allow them to build.
Fixes the following warnings in arch/arm/kernel/debug.c:
arch/arm/kernel/debug.S: Assembler messages:
arch/arm/kernel/debug.S:167: Error: too many positional arguments
arch/arm/kernel/debug.S:183: Error: too many positional arguments
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The decleration of error() as static in the platform specific uncompress
code in arch/arm/plat-samsung/include/plat/uncomopress.h causes the build
of the uncompressor to break. Remove it, as it is no longer needed.
arch/arm/boot/compressed/decompress.o: In function `gunzip':
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:67: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:73: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:80: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:95: undefined reference to `error'
/var/tmp/kernel-orig/arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:152: undefined reference to `error'
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Reset period_ns and duty_ns values in suspend handler to avoid skip of
configuration if same values passed to pwm_config;
Restore invertion bit in resume handler.
Without this patch PWM works incorrectly after resume from suspend.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch/arm/boot/compressed/decompress.o: In function `do_decompress':
decompress.c:(.text+0x26e8): undefined reference to `error'
decompress.c:(.text+0x2760): undefined reference to `error'
decompress.c:(.text+0x27d8): undefined reference to `error'
decompress.c:(.text+0x2824): undefined reference to `error'
decompress.c:(.text+0x28f0): undefined reference to `error'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is now changed to PLAT8250_DEV_PLATFORM (= 0), because
it's the only port that's going to be initialized in
Zoom 2/3 boards.
So, it doesn't make sense to keep the hardcoded 3 value anymore.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
This is useless, since in Zoom2/3 boards, the ports aren't even
physically accessible.
They must be explicitly initted in the board-zoom2.c, board-zoom3.c
and board-3630sdp.c files instead.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
As we have a struct device populated at the time we are
printing the errors, using dev_* macros makes more sense,
as could give a better idea where the error/warning came from.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Yauhen Kharuzhy