platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq(). Also use irq_get_trigger_type to get the
IRQ trigger flags.
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211220010411.12075-5-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The set/clear of the otg control values is done writing to
two different 16bit registers, however we setup the regmap
width for isp1760/61 to 32bit value bits.
So, just access the clear register address (0x376)as the high
part of the otg control register set (0x374), and write the
values in one go to make sure they get clear/set.
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210827131154.4151862-6-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using the fields enum values to check interrupts
trigged, use the correct bit values.
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210827131154.4151862-5-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We were already writing directly the port status register to
trigger changes in isp1763. The same is needed in other IP
from the family, including also to setup the read address
before reading from device.
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210827131154.4151862-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When trying to send bulks bigger than the biggest block size
we need to split them over several qtd. Fix this limiting the
maximum qtd size to largest block size.
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210827131154.4151862-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The loops to setup the memory pool were skipping some
blocks, that was not visible on the ISP1763 because it has
fewer blocks than the ISP1761. But won testing on that IP
from the family that would be an issue.
Reported-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Tested-by: Dietmar Eggemann <dietmar.eggemann@arm.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210827131154.4151862-2-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When CONFIG_USB_ISP1761_UDC is not enabled the udc_enabled variable is
never used since it is short circuited before in the logic operations.
This would trigger the following warning by clang analyzer:
drivers/usb/isp1760/isp1760-core.c:490:2: warning: Value stored to 'udc_enabled' is never read [clang-analyzer-deadcode.DeadStores]
udc_enabled = ((devflags & ISP1760_FLAG_ISP1763) ||
^
drivers/usb/isp1760/isp1760-core.c:490:2: note: Value stored to 'udc_enabled' is never read
Just swap the other of the operands in the logic operations.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-6-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Even though it is not expected, and would trigger a WARN_ON, killing a
transfer in a uninitialized slot this sequence is warned by clang
analyzer, twice:
drivers/usb/isp1760/isp1760-hcd.c:1976:18: warning: The result of the left shift is undefined because the right operand is negative [clang-analyzer-core.UndefinedBinaryOperatorResult]
skip_map |= (1 << qh->slot);
drivers/usb/isp1760/isp1760-hcd.c:1983:18: warning: The result of the left shift is undefined because the right operand is negative [clang-analyzer-core.UndefinedBinaryOperatorResult]
skip_map |= (1 << qh->slot);
Only set skip map if slot is active.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-5-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not really need to reset retval before get used bellow.
This will avoid the clang-analyzer warning:
drivers/usb/isp1760/isp1760-hcd.c:1919:2: warning: Value stored to 'retval' is never read [clang-analyzer-deadcode.DeadStores]
retval = 0;
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When checking if we need one more packet on a bulk pipe we may, even
though not probable at all, get there with a zero maxpacketsize.
In that case for sure no packet, no even a one more, will be
allocated.
This will clean the clang-analyzer warning:
drivers/usb/isp1760/isp1760-hcd.c:1856:38: warning: Division by zero [clang-analyzer-core.DivideZero]
&& !(urb->transfer_buffer_length %
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We do not care about the return value of that read between the
scratch register write and read, we really just want to make sure that
the pattern in the bus get changed to make sure we are testing
correctly the scratch pattern.
Clang-analyzer complains about the never read scratch variable:
>> drivers/usb/isp1760/isp1760-hcd.c:735:2: warning: Value stored to 'scratch' is never read [clang-analyzer-deadcode.DeadStores]
scratch = isp1760_hcd_read(hcd, HC_CHIP_ID_HIGH);
Just ignore the return value of that CHIP_ID_HIGH read, add more
information to the comment above why we are doing this. And as at it,
just do a small format change in the error message bellow.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210819180929.1327349-2-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If we fail to create qtd cache we were not destroying the
urb_listitem, rework the error handling logic to cope with that.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210727100516.4190681-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When polling for a setup or clear of a register field we were sleeping
in atomic context but using a very tight sleep interval.
Since the use cases for this poll mechanism are only in setup and
stop paths, and in practice this poll is not used most of the times
but needs to be there to comply to hardware setup times, remove the
sleep time and make the poll loop tighter.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210727100516.4190681-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove attribution to retval before check, which make it completely
meaningless, and does't check what it was supposed: the return
value of the timed function to set up configuration flag.
Fixes: 60d789f3bf ("usb: isp1760: add support for isp1763")
Tested-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Tong Tiangen <tongtiangen@huawei.com>
Link: https://lore.kernel.org/r/20210611014055.68551-1-tongtiangen@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/usb/isp1760/isp1760-udc.c:150: warning: Function parameter or member 'udc' not described in 'isp1760_udc_select_ep'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: linux-usb@vger.kernel.org
Reviewed-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210526130037.856068-7-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Besides the already host mode support add peripheral mode support for
the isp1763 IP from the isp1760 family.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-10-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1763 have some differences from the isp1760, 8 bit address for
registers and 16 bit for values, no bulk access to memory addresses,
16 PTD's instead of 32.
Following the regmap work done before add the registers, memory access
and add the functions to support differences in setup sequences.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-8-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is already a binding to describe the dual role mode (dr_mode),
use that instead of defining a new one (port1-otg).
Update driver code and devicetree files that use that port1-otg
binding.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-7-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to support other family member IP, which may have
different memory layout. Drop macros and setup a configuration
struct.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-6-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the removal of the Blackfin port with:
commit 4ba66a9760 ("arch: remove blackfin port")
No one is using or referencing this header and platform data struct.
Remove them.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-5-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use io relaxed access memory primitives to satisfy strict type
checking (__force).
This will fix some existing sparse warnings:
sparse: warning: cast to restricted __le32
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-4-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rework access to registers and memory to use regmap framework.
No change in current feature or way of work is intended with this
change.
This will allow to reuse this driver with other IP of this family,
for example isp1763, with little changes and effort.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-3-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a lot of pre-existing typechecking warnings around the
access and assign of elements of ptd structure of __dw type.
sparse: warning: invalid assignment: |=
sparse: left side has type restricted __dw
sparse: right side has type unsigned int
or
warning: restricted __dw degrades to integer
or
sparse: warning: incorrect type in assignment (different base types)
sparse: expected restricted __dw [usertype] dw4
sparse: got unsigned int [assigned] [usertype] usof
To handle this, annotate conversions along the {TO,FROM}_DW* macros
and some assignments and function arguments.
This clean up completely all sparse warnings for this driver.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Link: https://lore.kernel.org/r/20210513084717.2487366-2-rui.silva@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch corrects the SPDX License Identifier style in
header files related to ISP1760 USB host controller.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used).
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Link: https://lore.kernel.org/r/20200404093803.GA4983@nishad
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
As the "else if" and "else" branch body are identical the condition
has no effect. So drop the else if condition.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
Link: https://lore.kernel.org/r/20191005053733.GA10727@saurav
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/usb/isp1760/isp1760-hcd.c: In function ‘collect_qtds’:
drivers/usb/isp1760/isp1760-hcd.c:788:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
mem_reads8(hcd->regs, qtd->payload_addr,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
qtd->data_buffer,
~~~~~~~~~~~~~~~~~
qtd->actual_length);
~~~~~~~~~~~~~~~~~~~
drivers/usb/isp1760/isp1760-hcd.c:792:5: note: here
case OUT_PID:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable 'selector' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'selector' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1760_stop() is never called in atomic context.
The call chain ending up at isp1760_stop() is:
[1] isp1760_stop() <- isp1760_shutdown()
isp1760_shutdown() is set as ".shutdown" in struct hc_driver.
isp1760_stop() is also set as ".stop" in hc_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1760_stop()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
isp1760_init_core() is never called in atomic context.
The call chains ending up at isp1760_init_core() are:
[1] isp1760_init_core() <- isp1760_register() <- isp1760_plat_probe()
[2] isp1760_init_core() <- isp1760_register() <- isp1761_pci_probe()
isp1760_plat_probe() is set as ".probe" in struct platform_driver.
isp1761_pci_probe() is set as ".probe" in struct pci_driver.
These functions are not called in atomic context.
Despite never getting called from atomic context, isp1761_pci_probe()
calls mdelay() to busily wait.
This is not necessary and can be replaced with msleep() to
avoid busy waiting.
This is found by a static analysis tool named DCNS written by myself.
And I also manually check it.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kasprintf instead of combination of kmalloc and sprintf and
therefore avoid unnecessary computation of string length.
Also, remove the useless local variable.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
This updates the remaining drivers/usb/*Makefile* that were missing SPDX
identifiers. They all get the following identifier:
SPDX-License-Identifier: GPL-2.0
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Johan Hovold <johan@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: "Gustavo A. R. Silva" <garsilva@embeddedor.com>
Cc: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify return logic to avoid unnecessary variable assignment.
This issue was detected using Coccinelle and the following
semantic patch:
@@
local idexpression ret;
expression e;
@@
-ret =
+return
e;
-return ret;
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.
when say N here it will not build PCI related code in USB driver.
Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Declare usb_gadget_ops structures as const as they are only stored in
the ops field of a usb_gadget structure. This field is of type const, so
usb_gadget_ops structures having this property can be declared const
too.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct usb_gadget_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct isp1760_udc udc;
@@
udc.gadget.ops=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct usb_gadget_ops i;
File size before: drivers/usb/isp1760/isp1760-udc.o
text data bss dec hex filename
12434 4136 16 16586 40ca usb/isp1760/isp1760-udc.o
File size after: drivers/usb/isp1760/isp1760-udc.o
text data bss dec hex filename
12530 4048 16 16594 40d2 usb/isp1760/isp1760-udc.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the more common logging mechanism.
Miscellanea:
o Realign multiline statements
o Coalesce format
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove unnecessary space before open square bracket.
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert endpoint configuration to new capabilities model.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since maxpacket_limit was introduced all UDC drivers should use
usb_ep_set_maxpacket_limit() function instead of setting maxpacket value
manually. ep.maxpacket_limit contains actual maximum maxpacket value
supported by hardware which is needed by epautoconf.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
isp1760_ep_alloc_request allocates a structure with kzalloc without checking
for NULL and then returns a pointer to one of the structure fields. As the
field happens to be the first in the structure the caller can properly check
for NULL, but this is risky if the structure layout is changed later. Add an
explicit NULL check for the kzalloc return value
Detected with smatch static analysis:
drivers/usb/isp1760/isp1760-udc.c:816 isp1760_ep_alloc_request()
error: potential null dereference 'req'. (kzalloc returns null)
[ thanks to Laurent Pinchart for improved commit message ]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Lad Prabhakar