Commit Graph

67 Commits

Author SHA1 Message Date
Jack Morgenstein 114840c3d2 mlx4_core: Add support for secure-host and SMP firewall
Secure-host is the general term for the capability of a device
to protect itself and the subnet from malicious host software.

This is achieved by:
1. Not allowing un-trusted entities to access device configuration
   registers, directly (through pci_cr or pci_conf) and indirectly
   (through MADs).

2. Hiding M_Key from untrusted entities.

3. Preventing the modification of GUID0 by un-trusted entities

4. Not allowing drivers on untrusted hosts to receive nor to transmit
   packets over QP0 (SMP Firewall).

The secure-host capability depends on firmware handling all QP0
packets, and not passing these packets up to the driver. Any information
required by the driver for proper operation (e.g., SM lid) is passed
via events generated by the firmware while processing QP0 MADs.

Driver support mainly requires using the MAD_DEMUX FW command at startup,
where the feature is enabled/disabled through a procedure described in
the Mellanox HCA tools package.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>

[ Fix error path in mlx4_setup_hca to go to err_mcg_table_free. - Roland ]

Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-08-05 07:40:22 -07:00
Linus Torvalds f9da455b93 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next
Pull networking updates from David Miller:

 1) Seccomp BPF filters can now be JIT'd, from Alexei Starovoitov.

 2) Multiqueue support in xen-netback and xen-netfront, from Andrew J
    Benniston.

 3) Allow tweaking of aggregation settings in cdc_ncm driver, from Bjørn
    Mork.

 4) BPF now has a "random" opcode, from Chema Gonzalez.

 5) Add more BPF documentation and improve test framework, from Daniel
    Borkmann.

 6) Support TCP fastopen over ipv6, from Daniel Lee.

 7) Add software TSO helper functions and use them to support software
    TSO in mvneta and mv643xx_eth drivers.  From Ezequiel Garcia.

 8) Support software TSO in fec driver too, from Nimrod Andy.

 9) Add Broadcom SYSTEMPORT driver, from Florian Fainelli.

10) Handle broadcasts more gracefully over macvlan when there are large
    numbers of interfaces configured, from Herbert Xu.

11) Allow more control over fwmark used for non-socket based responses,
    from Lorenzo Colitti.

12) Do TCP congestion window limiting based upon measurements, from Neal
    Cardwell.

13) Support busy polling in SCTP, from Neal Horman.

14) Allow RSS key to be configured via ethtool, from Venkata Duvvuru.

15) Bridge promisc mode handling improvements from Vlad Yasevich.

16) Don't use inetpeer entries to implement ID generation any more, it
    performs poorly, from Eric Dumazet.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1522 commits)
  rtnetlink: fix userspace API breakage for iproute2 < v3.9.0
  tcp: fixing TLP's FIN recovery
  net: fec: Add software TSO support
  net: fec: Add Scatter/gather support
  net: fec: Increase buffer descriptor entry number
  net: fec: Factorize feature setting
  net: fec: Enable IP header hardware checksum
  net: fec: Factorize the .xmit transmit function
  bridge: fix compile error when compiling without IPv6 support
  bridge: fix smatch warning / potential null pointer dereference
  via-rhine: fix full-duplex with autoneg disable
  bnx2x: Enlarge the dorq threshold for VFs
  bnx2x: Check for UNDI in uncommon branch
  bnx2x: Fix 1G-baseT link
  bnx2x: Fix link for KR with swapped polarity lane
  sctp: Fix sk_ack_backlog wrap-around problem
  net/core: Add VF link state control policy
  net/fsl: xgmac_mdio is dependent on OF_MDIO
  net/fsl: Make xgmac_mdio read error message useful
  net_sched: drr: warn when qdisc is not work conserving
  ...
2014-06-12 14:27:40 -07:00
Linus Torvalds 1d21b1bf53 Main batch of InfiniBand/RDMA changes for 3.16:
- Add iWARP port mapper to avoid conflicts between RDMA and normal
    stack TCP connections.
 
  - Fixes for i386 / x86-64 structure padding differences (ABI
    compatibility for 32-on-64) from Yann Droneaud.
 
  - A pile of SRP initiator fixes from Bart Van Assche.
 
  - Fixes for a writeback / memory allocation deadlock with NFS over
    IPoIB connected mode from Jiri Kosina.
 
  - The usual fixes and cleanups to mlx4, mlx5, cxgb4 and other
    low-level drivers.
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v1
 
 iQIcBAABCAAGBQJTlzyEAAoJEENa44ZhAt0h9yoP/1UeXlejOpCJyiNdtJZ+ilcU
 cb0PEzsjzqACyDqcoQ0EpQM3/3emccVIC3uUXK12mzlTIXOFYTeRLays/TbxZDLt
 FK5D/NrMmmJmciPt1ZRgUX82kFFRGScEfpkXYs7jxtRaNT7CW5KwSNQr6aFXskUz
 1gpdK1ARCN5rWcGl2HJx5o9C4c/Fa/Vov8lOsAkUZXD1SuPNT/fFN0u1pRzU68g0
 k3oj81XnZq5ejOBQKXEHImcmjXwaJ2yjmzxhSsKebqDWDdXuS/F9e4taKneHTZmr
 AdwJaLLJPWmAGi/vYYhkuLKpzIDpzMCqwr39lEabmjWvznYOlnjfVUXwUTE2nwNC
 DIXuHOLFrSvF2cNxh8ZeEYKS8AV+PjAOahPC5whkWkY256Q67uB7cy9ilWAK+7xS
 QcQ5Inr6iXvxIGYA4hNwUo8aK0NuKFwhkVVFEbkPaurbQZPqiKwyVE3w2FOws/Qp
 0kLLCVvpRQYjKzkxyof2tb1AcNuVNKXHrYk6RaBDJ9mjxHbhvY4OSt4CBxAAXBu6
 zoedUydN1Nz1UgAB1jDsBdyE2QQnXockA1+JJKNq6gM5Dz0DUdAylzQ2NqY9tnYz
 RTzihEPYIiQUkV3B8ErbqsuO6z7M830AXO5AR6bLZn1zgJ0cbMLBaKLA8LRufJI/
 qxNVwL32Uv1PjKZ+yX1x
 =Wcdc
 -----END PGP SIGNATURE-----

Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband

Pull main InfiniBand/RDMA updates from Roland Dreier:

 - add iWARP port mapper to avoid conflicts between RDMA and normal
   stack TCP connections.

 - fixes for i386 / x86-64 structure padding differences (ABI
   compatibility for 32-on-64) from Yann Droneaud.

 - a pile of SRP initiator fixes from Bart Van Assche.

 - fixes for a writeback / memory allocation deadlock with NFS over
   IPoIB connected mode from Jiri Kosina.

 - the usual fixes and cleanups to mlx4, mlx5, cxgb4 and other low-level
   drivers.

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (61 commits)
  RDMA/cxgb4: Add support for iWARP Port Mapper user space service
  RDMA/nes: Add support for iWARP Port Mapper user space service
  RDMA/core: Add support for iWARP Port Mapper user space service
  IB/mlx4: Fix gfp passing in create_qp_common()
  IB/umad: Fix use-after-free on close
  IB/core: Fix kobject leak on device register error flow
  RDMA/cxgb4: add missing padding at end of struct c4iw_alloc_ucontext_resp
  mlx4_core: Fix GFP flags parameters to be gfp_t
  IB/core: Fix port kobject deletion during error flow
  IB/core: Remove unneeded kobject_get/put calls
  IB/core: Fix sparse warnings about redeclared functions
  IB/mad: Fix sparse warning about gfp_t use
  IB/mlx4: Implement IB_QP_CREATE_USE_GFP_NOIO
  IB: Add a QP creation flag to use GFP_NOIO allocations
  IB: Return error for unsupported QP creation flags
  IB: Allow build of hw/ and ulp/ subdirectories independently
  mlx4_core: Move handling of MLX4_QP_ST_MLX to proper switch statement
  RDMA/cxgb4: Add missing padding at end of struct c4iw_create_cq_resp
  IB/srp: Avoid problems if a header uses pr_fmt
  IB/umad: Fix error handling
  ...
2014-06-10 10:41:33 -07:00
Jack Morgenstein 65fed8a8c1 IB/mlx4: Add interface for selecting VFs to enable QP0 via MLX proxy QPs
This commit adds the sysfs interface for enabling QP0 on VFs for
selected VF/port.

By default, no VFs are enabled for QP0 operation.

To enable QP0 operation on a VF/port, under
/sys/class/infiniband/mlx4_x/iov/<b:d:f>/ports/x there are two new entries:

- smi_enabled (read-only). Indicates whether smi is currently
  enabled for the indicated VF/port

- enable_smi_admin (rw). Used by the admin to request that smi
  capability be enabled or disabled for the indicated VF/port.
  0 = disable, 1 = enable.
  The requested enablement will occur at the next reset of the
  VF (e.g. driver restart on the VM which owns the VF).

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:13:19 -07:00
Jack Morgenstein 99ec41d0a4 mlx4: Add infrastructure for selecting VFs to enable QP0 via MLX proxy QPs
This commit adds the infrastructure for enabling selected VFs to
operate SMI (QP0) MADs without restriction.

Additionally, for these enabled VFs, their QP0 proxy and tunnel QPs
are MLX QPs.  As such, they operate over VL15.  Therefore, they are
not affected by "credit" problems or changes in the VLArb table (which
may shut down VL0).

Non-enabled VFs may only create UD proxy QP0 qps (which are forced by
the hypervisor to send packets using the q-key it assigns and places
in the qp-context).  Thus, non-enabled VFs will not pose a security
risk.  The hypervisor discards any privileged MADs it receives from
these non-enabled VFs.

By default, all VFs are NOT enabled, and must explicitly be enabled
by the administrator.

The sysfs interface which operates the VF enablement infrastructure
is provided in the next commit.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:13:09 -07:00
Jack Morgenstein 97982f5a91 IB/mlx4: Preparation for VFs to issue/receive SMI (QP0) requests/responses
Currently, VFs in SRIOV VFs are denied QP0 access.  The main reason
for this decision is security, since Subnet Management Datagrams
(SMPs) are not restricted by network partitioning and may affect the
physical network topology.  Moreover, even the SM may be denied access
from portions of the network by setting management keys unknown to the
SM.

However, it is desirable to grant SMI access to certain privileged
VFs, so that certain network management activities may be conducted
within virtual machines instead of the hypervisor.

This commit does the following:

1. Create QP0 tunnel QPs for all VFs.

2. Discard SMI mads sent-from/received-for non-privileged VFs in the
   hypervisor MAD multiplex/demultiplex logic.  SMI mads from/for
   privileged VFs are allowed to pass.

3. MAD_IFC wrapper changes/fixes.  For non-privileged VFs, only
   host-view MAD_IFC commands are allowed, and only for SMI LID-Routed
   GET mads.  For privileged VFs, there are no restrictions.

This commit does not allow privileged VFs as yet.  To determine if a VF
is privileged, it calls function mlx4_vf_smi_enabled().  This function
returns 0 unconditionally for now.

The next two commits allow defining and activating privileged VFs.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-05-29 21:12:58 -07:00
David S. Miller 54e5c4def0 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/bonding/bond_alb.c
	drivers/net/ethernet/altera/altera_msgdma.c
	drivers/net/ethernet/altera/altera_sgdma.c
	net/ipv6/xfrm6_output.c

Several cases of overlapping changes.

The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.

In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.

Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.

Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-24 00:32:30 -04:00
Sucheta Chakraborty ed616689a3 net-next:v4: Add support to configure SR-IOV VF minimum and maximum Tx rate through ip tool.
o min_tx_rate puts lower limit on the VF bandwidth. VF is guaranteed
  to have a bandwidth of at least this value.
  max_tx_rate puts cap on the VF bandwidth. VF can have a bandwidth
  of up to this value.

o A new handler set_vf_rate for attr IFLA_VF_RATE has been introduced
  which takes 4 arguments:
  netdev, VF number, min_tx_rate, max_tx_rate

o ndo_set_vf_rate replaces ndo_set_vf_tx_rate handler.

o Drivers that currently implement ndo_set_vf_tx_rate should now call
  ndo_set_vf_rate instead and reject attempt to set a minimum bandwidth
  greater than 0 for IFLA_VF_TX_RATE when IFLA_VF_RATE is not yet
  implemented by driver.

o If user enters only one of either min_tx_rate or max_tx_rate, then,
  userland should read back the other value from driver and set both
  for IFLA_VF_RATE.
  Drivers that have not yet implemented IFLA_VF_RATE should always
  return min_tx_rate as 0 when read from ip tool.

o If both IFLA_VF_TX_RATE and IFLA_VF_RATE options are specified, then
  IFLA_VF_RATE should override.

o Idea is to have consistent display of rate values to user.

o Usage example: -

  ./ip link set p4p1 vf 0 rate 900

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 900 (Mbps), max_tx_rate 900Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 300 min_tx_rate 200

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f0 brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5a, tx rate 300 (Mbps), max_tx_rate 300Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

  ./ip link set p4p1 vf 0 max_tx_rate 600 rate 300

  ./ip link show p4p1
  32: p4p1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
  DEFAULT qlen 1000
    link/ether 00:0e:1e:08:b0:f brd ff:ff:ff:ff:ff:ff
    vf 0 MAC 3e:a0:ca:bd:ae:5, tx rate 600 (Mbps), max_tx_rate 600Mbps,
    min_tx_rate 200Mbps
    vf 1 MAC f6:c6:7c:3f:3d:6c
    vf 2 MAC 56:32:43:98:d7:71
    vf 3 MAC d6:be:c3:b5:85:ff
    vf 4 MAC ee:a9:9a:1e:19:14
    vf 5 MAC 4a:d0:4c:07:52:18
    vf 6 MAC 3a:76:44:93:62:f9
    vf 7 MAC 82:e9:e7:e3:15:1a

Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-23 15:04:02 -04:00
Amir Vadai c20862c802 net/mlx4_core: Replace pr_warning() with pr_warn()
As checkpatch suggests. Also changed some printk's into pr_*

Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-22 17:17:29 -04:00
Matan Barak ce8d9e0d67 net/mlx4_core: Add UPDATE_QP SRIOV wrapper support
This patch adds UPDATE_QP SRIOV wrapper support.

The mechanism is a general one, but currently only source MAC
index changes are allowed for VFs.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-16 15:12:45 -04:00
Eyal Perry c05a116f39 net/mlx4_core: Fix smatch error - possible access to a null variable
Fix the "error: we previously assumed 'out_param' could be null" found
by smatch semantic checker on:
drivers/net/ethernet/mellanox/mlx4/cmd.c:506 mlx4_cmd_poll()
drivers/net/ethernet/mellanox/mlx4/cmd.c:578 mlx4_cmd_wait()

Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-14 15:40:33 -04:00
Joe Perches 1a91de2883 mellanox: Logging message cleanups
Use a more current logging style.

o Coalesce formats
o Add missing spaces for coalesced formats
o Align arguments for modified formats
o Add missing newlines for some logging messages
o Use DRV_NAME as part of format instead of %s, DRV_NAME to
  reduce overall text.
o Use ..., ##__VA_ARGS__ instead of args... in macros
o Correct a few format typos
o Use a single line message where appropriate

Signed-off-by: Joe Perches <joe@perches.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-05-08 23:42:02 -04:00
Or Gerlitz d18f141a1a mlx4: Add support for CONFIG_DEV command
Introduce the CONFIG_DEV firmware command which we will use to
configure the UDP port assumed by the firmware for the VXLAN offloads.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 16:29:35 -04:00
Or Gerlitz b74757944d net/mlx4: USe one wrapper that returns -EPERM
When a VF issues a firmware command which is disallowed for them, the PF
rerturns -EPERM from that command wrapper. Move to use one such wrapper
instance, instead of repeating the same code on such commands.

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-28 16:29:35 -04:00
Matan Barak 449fc48866 net/mlx4: Adapt code for N-Port VF
Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-20 16:18:30 -04:00
Matan Barak f74462acf8 net/mlx4: Add utils for N-Port VFs
This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-20 16:18:29 -04:00
Jack Morgenstein 5ea8bbfc49 mlx4: Implement IP based gids support for RoCE/SRIOV
Since there is no connection between the MAC/VLAN and the GID
when using IP-based addressing, the proxy QP1 (running on the
slave) must pass the source-mac, destination-mac, and vlan_id
information separately from the GID. Additionally, the Host
must pass the remote source-mac and vlan_id back to the slave,

This is achieved as follows:
Outgoing MADs:
    1. Source MAC: obtained from the CQ completion structure
       (struct ib_wc, smac field).
    2. Destination MAC: obtained from the tunnel header
    3. vlan_id: obtained from the tunnel header.
Incoming MADs
    1. The source (i.e., remote) MAC and vlan_id are passed in
       the tunnel header to the proxy QP1.

VST mode support:
     For outgoing MADs,  the vlan_id obtained from the header is
        discarded, and the vlan_id specified by the Hypervisor is used
        instead.
     For incoming MADs, the incoming vlan_id (in the wc) is discarded, and the
        "invalid" vlan (0xffff)  is substituted when forwarding to the slave.

Signed-off-by: Moni Shoua <monis@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2014-03-12 15:57:16 -04:00
Matan Barak 4de6580360 mlx4_core: Add support for steerable IB UD QPs
This patch adds support for allocating IB UD QPs that we can steer
traffic from.  We introduce a new firmware command FLOW_STEERING_IB_UC_QP_RANGE
and a capability bit.

This command isn't supported for VFs.

Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2014-01-14 14:06:50 -08:00
Rony Efraim f0f829bf42 net/mlx4_core: Add immediate activate for VGT->VST->VGT
Allow immediate activate of VGT->VST and VST->VGT transitions, without
the need of rebinding in mlx4_master_immediate_activate_vlan_qos().

Also in struct res_qp: add qp parameters (vlan_index,fvl,vlan_cntrol..)
to the saved set, in order to restore when move to VGT.
 - Clear at mlx4_RST2INIT_QP_wrapper()
 - Save at mlx4_INIT2RTR_QP_wrapper()
 - Restore at mlx4_vf_immed_vlan_work_handler()

Update mlx4_vf_immed_vlan_work_handler() to support VGT.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-07 19:22:47 -05:00
Jack Morgenstein 571b8b92c7 net/mlx4_core: Initialize all mailbox buffers to zero before use
To guarantee that all unused fields in all FW commands for both inboxes
and outboxes are zeroed out, initialize the mailbox buffer to all zeroes.

This is especially important for SRIOV comm-channel virtual commands
(such as QUERY_FUNC_CAP), where if new fields are added to support new
features, the driver can depend on older kernels passing zeroes in these
fields.

In addition to zeroing out the mailbox buffer at allocation time, all
(now unnecessary) calls to memset by the callers of
mlx4_alloc_cmd_mailbox() are removed.

Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-07 19:22:47 -05:00
Jack Morgenstein 2c957ff27d net/mlx4_core: Don't fail reg/unreg vlan for older guests
In upstream kernels under SRIOV, the vlan register/unregister calls
were NOPs (doing nothing and returning OK). We detect these old
calls from guests (via the comm channel), since previously the
port number in mlx4_register_vlan was passed (improperly) in the
out_param. This has been corrected so that the port number is now
passed in bits 8..15 of the in_modifier field.

For old calls, these bits will be zero, so if the passed port
number is zero, we can still look at the out_param field to see
if it contains a valid port number. If yes, the VM is running
an old driver.

Since for old drivers, the register/unregister_vlan wrappers were
NOPs, we continue this policy -- the reason being that upstream
had an additional bug in eth driver running on guests (where
procedure mlx4_en_vlan_rx_kill_vid() had the following code:

if (!mlx4_find_cached_vlan(mdev->dev, priv->port, vid, &idx))
        mlx4_unregister_vlan(mdev->dev, priv->port, idx);
else
        en_err(priv, "could not find vid %d in cache\n", vid);

On a VM, mlx4_find_cached_vlan() will always fail, since the
vlan cache is located on the Hypervisor; on guests it is empty.

Therefore, if we allow upstream guests to register vlans, we will
have vlan leakage since the unregister will never be performed.
Leaving vlan reg/unreg for old guest drivers as a NOP is not a
feature regression, since in upstream the register/unregister
vlan wrapper is a NOP.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 16:19:07 -05:00
Jack Morgenstein 2009d0059c net/mlx4_en: Use vlan id instead of vlan index for unregistration
Use of vlan_index created problems unregistering vlans on guests.

In addition, tools delete vlan by tag, not by index, lets follow that.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 16:19:07 -05:00
David S. Miller 394efd19d5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts:
	drivers/net/ethernet/emulex/benet/be.h
	drivers/net/netconsole.c
	net/bridge/br_private.h

Three mostly trivial conflicts.

The net/bridge/br_private.h conflict was a function signature (argument
addition) change overlapping with the extern removals from Joe Perches.

In drivers/net/netconsole.c we had one change adjusting a printk message
whilst another changed "printk(KERN_INFO" into "pr_info(".

Lastly, the emulex change was a new inline function addition overlapping
with Joe Perches's extern removals.

Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 13:48:30 -05:00
Jack Morgenstein c32b7dfbb1 net/mlx4_core: Fix call to __mlx4_unregister_mac
In function mlx4_master_deactivate_admin_state() __mlx4_unregister_mac was
called using the MAC index. It should be called with the value of the MAC itself.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-11-04 00:51:10 -05:00
Or Gerlitz fe66bb2db5 net/mlx4: Clean the code to eliminate trivial build warnings
Remove code that triggers trivial build warnings.

drivers/net/ethernet/mellanox/mlx4/cmd.c: In function ‘mlx4_set_vf_vlan’:
drivers/net/ethernet/mellanox/mlx4/cmd.c:2256: warning: variable ‘vf_oper’ set but not used
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_mode’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:648: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_map_sw_to_hw_steering_id’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:685: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/mcg.c: In function ‘mlx4_hw_rule_sz’:
drivers/net/ethernet/mellanox/mlx4/mcg.c:712: warning: comparison of unsigned expression < 0 is always false
drivers/net/ethernet/mellanox/mlx4/fw.c: In function ‘mlx4_opreq_action’:
drivers/net/ethernet/mellanox/mlx4/fw.c:1732: warning: variable ‘type_m’ set but not used
drivers/net/ethernet/mellanox/mlx4/srq.c:302: warning: no previous prototype for ‘mlx4_srq_lookup’

Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-10-17 15:10:49 -04:00
Jingoo Han f094668ca1 net: mlx4: Staticize local functions
These local functions are used only in this file.
Fix the following sparse warnings:

drivers/net/ethernet/mellanox/mlx4/cmd.c:803:5: warning: symbol 'MLX4_CMD_UPDATE_QP_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:812:5: warning: symbol 'MLX4_CMD_GET_OP_REQ_wrapper' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx4/cmd.c:1547:5: warning: symbol 'mlx4_master_immediate_activate_vlan_qos' was not declared. Should
it be static?

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-08-05 11:05:24 -07:00
Yevgeny Petrilin fe6f700d6c net/mlx4_core: Respond to operation request by firmware
This commit adds new firmware command and new firmware event.  The firmware
raises the MLX4_EVENT_TYPE_OP_REQUIRED event in order to signal the driver it
needs to perform an administrative operation throughout the MLX4_CMD_GET_OP_REQ
command. At the moment the supported operation is adding/removing multicast
entries which are used by the firmware for handling NCSI traffic in B0
steering mode.

Also, had to swap the order of mlx4_init_mcg_table() and
mlx4_init_eq_table() to make sure that driver will get events only after
resources are initialized to handle it.

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-29 01:12:40 -07:00
Dan Carpenter 9caf83c32b net/mlx4: fix small memory leak on error
"work" needs to be freed before returning on this error path.

Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-03 16:52:10 -07:00
Rony Efraim 0a6eac2458 net/mlx4_core: Add HW enforcement to VF link state
When the firmware supports the UPDATE_QP command, if the VF link is disabled,
block all QPs opened by the VF, by programming the UPDATE_QP command to drop
all RX & TX traffic to/from these QPs. Operates only in VST mode.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-01 13:10:57 -07:00
Jack Morgenstein b01978cacf net/mlx4_core: Dynamic VST to VST vlan/qos changes
Within VST mode, enable modifying the vlan and/or qos
for a VF without requiring unbind/rebind.

This requires firmware which supports the UPDATE_QP command.
(If the command is not available, we fall back to requiring
unbind/bind to activate these changes).

To avoid race conditions with modify-qp on QPs that are affected
by update-qp, this operation is performed on the comm_wq.

If the update operation succeeds for all the necessary QPs, a
vlan_unregister is performed for the abandoned vlan id.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-07-01 13:10:22 -07:00
Dotan Barak 674925edb4 net/mlx4_core: Add warning in case of command timeouts
Warning prints when there are command timeout to help debugging future
failures.

Signed-off-by: Dotan Barak <dotanb@dev.mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-25 16:29:39 -07:00
Rony Efraim 948e306d7d net/mlx4: Add VF link state support
Add support to change the link state of VF (vPort)

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-13 17:51:04 -07:00
Jack Morgenstein 5efe5355f2 net/mlx4_core: Return -EPROBE_DEFER when a VF is probed before PF is sufficiently initialized
In the PF initialization, SRIOV is enabled before the PF is fully initialized.
This allows the kernel to probe the newly-exposed VFs before the PF is ready
to handle them (nested probes).

Have the probe method return the -EPROBE_DEFER value in this situation (instead
of the VF probe method retrying its initialization in a loop, and returning -EIO
on failure). When -EPROBE_DEFER is returned by the VF probe method, the kernel
itself will retry the probe after a suitable delay.

Based upon a suggestion by Ben Hutchings <bhutchings@solarflare.com>

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-06-04 12:58:24 -07:00
Rony Efraim 2cccb9e4f3 net/mlx4: Add support to get VF config
Support getting VF config.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:14 -04:00
Rony Efraim e6b6a23163 net/mlx4: Add VF MAC spoof checking support
Add ndo_set_vf_spoofchk support

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:14 -04:00
Rony Efraim 3f7fb021d0 net/mlx4: Add set VF default vlan ID and priority support
Add support to ndo_set_vf_vlan in the driver. Once this call is used the vport
is considered to be in VST mode. In this mode, the PPF driver configures
Ethernet QPs created by this VF to use this vlan id and priority. Currently
RoCE isn't supported on that mode.

The special values of VID=4095 or VID=0,UP=0 are considered as VGT.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:13 -04:00
Rony Efraim 8f7ba3ca12 net/mlx4: Add set VF mac address support
Add ndo_set_vf_mac support which allows to set the MAC address
for mlx4 VF Ethernet NICs from the host.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:13 -04:00
Rony Efraim 0eb62b93cb net/mlx4: Add structures to keep VF Ethernet ports information
This patch add struct mlx4_vport_state where all the parameters related
to management of VFs port (virtual ports of the NIC eswitch) are kept.

The driver keeps an administrative and operational copy of the settings.
The current administrative copy becomes operational on the event of probing
a VF either on a VM or on the host.

Signed-off-by: Rony Efraim <ronye@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-04-26 23:29:13 -04:00
Joe Perches d0320f7500 drivers:net: Remove dma_alloc_coherent OOM messages
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.

Remove the unnecessary additional error logging.

Around these deletions:

o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2013-03-15 08:56:58 -04:00
Jack Morgenstein 311f813a2d mlx4_core: Fix potential deadlock in mlx4_eq_int()
The slave_state_lock spinlock is used in both interrupt context and
process context, hence irq locking must be used.  Found by lockdep.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-11-29 12:14:54 -08:00
Or Gerlitz 08ff32352d mlx4: 64-byte CQE/EQE support
ConnectX-3 devices can use either 64- or 32-byte completion queue
entries (CQEs) and event queue entries (EQEs).  Using 64-byte
EQEs/CQEs performs better because each entry is aligned to a complete
cacheline.  This patch queries the HCA's capabilities, and if it
supports 64-byte CQEs and EQES the driver will configure the HW to
work in 64-byte mode.

The 32-byte vs 64-byte mode is global per HCA and not per CQ or EQ.

Since this mode is global, userspace (libmlx4) must be updated to work
with the configured CQE size, and guests using SR-IOV virtual
functions need to know both EQE and CQE size.

In case one of the 64-byte CQE/EQE capabilities is activated, the
patch makes sure that older guest drivers that use the QUERY_DEV_FUNC
command (e.g as done in mlx4_core of Linux 3.3..3.6) will notice that
they need an update to be able to work with the PPF. This is done by
changing the returned pf_context_behaviour not to be zero any more. In
case none of these capabilities is activated that value remains zero
and older guest drivers can run OK.

The SRIOV related flow is as follows

1. the PPF does the detection of the new capabilities using
   QUERY_DEV_CAP command.

2. the PPF activates the new capabilities using INIT_HCA.

3. the VF detects if the PPF activated the capabilities using
   QUERY_HCA, and if this is the case activates them for itself too.

Note that the VF detects that it must be aware to the new PF behaviour
using QUERY_FUNC_CAP.  Steps 1 and 2 apply also for native mode.

User space notification is done through a new field introduced in
struct mlx4_ib_ucontext which holds device capabilities for which user
space must take action. This changes the binary interface so the ABI
towards libmlx4 exposed through uverbs is bumped from 3 to 4 but only
when **needed** i.e. only when the driver does use 64-byte CQEs or
future device capabilities which must be in sync by user space. This
practice allows to work with unmodified libmlx4 on older devices (e.g
A0, B0) which don't support 64-byte CQEs.

In order to keep existing systems functional when they update to a
newer kernel that contains these changes in VF and userspace ABI, a
module parameter enable_64b_cqe_eqe must be set to enable 64-byte
mode; the default is currently false.

Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-11-26 10:19:17 -08:00
Roland Dreier f3d4c89ee4 mlx4_core: Fix crash on uninitialized priv->cmd.slave_sem
On an SR-IOV master device, __mlx4_init_one() calls mlx4_init_hca()
before mlx4_multi_func_init().  However, for unlucky configurations,
mlx4_init_hca() might call mlx4_SENSE_PORT() (via mlx4_dev_cap()), and
that calls mlx4_cmd_imm() with MLX4_CMD_WRAPPED set.

However, on a multifunction device with MLX4_CMD_WRAPPED, __mlx4_cmd()
calls into mlx4_slave_cmd(), and that immediately tries to do

	down(&priv->cmd.slave_sem);

but priv->cmd.slave_sem isn't initialized until mlx4_multi_func_init()
(which we haven't called yet).  The next thing it tries to do is access
priv->mfunc.vhcr, but that hasn't been allocated yet.

Fix this by moving the initialization of slave_sem and vhcr up into
mlx4_cmd_init(). Also, since slave_sem is really just being used as a
mutex, convert it into a slave_cmd_mutex.

Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:46 -07:00
Jack Morgenstein afa8fd1db9 mlx4: Paravirtualize Node Guids for slaves
This is necessary in order to support > 1 VF/PF in a VM for software
that uses the node guid as a discriminator, such as librdmacm.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:43 -07:00
Jack Morgenstein 992e8e6e87 IB/mlx4: Miscellaneous adjustments for SR-IOV IB support
1. Allow only master to change node description.
2. Prevent AH leakage in send mads.
3. Take device part number from PCI structure, so that guests see the
   VF part number (and not the PF part number).
4. Place the device revision ID into caps structure at startup.
5. SET_PORT in update_gids_task needs to go through wrapper on master.
6. In mlx4_ib_event(), PORT_MGMT_EVENT needs be handled in a work
   queue on the master, since it propagates events to slaves using
   GEN_EQE.
7. Do not support FMR on slaves.
8. Add spinlock to slave_event(), since it is called both in interrupt
   context and in process context (due to 6 above, and also if
   smp_snoop is used).  This fix was found and implemented by Saeed
   Mahameed <saeedm@mellanox.com>

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:41 -07:00
Jack Morgenstein a0c64a17ab mlx4: Add alias_guid mechanism
For IB ports, we paravirtualize the GUID at index 0 on slaves.  The
GUID at index 0 seen by a slave is the actual GUID occupying the GUID
table at the slave-id index.

The driver, by default, requests at startup time that subnet manager
populate its entire guid table with GUIDs. These guids are then mapped
(paravirtualized) to the slaves, and appear for each slave as its GUID
at index 0.

Until each slave has such a guid, its port status is DOWN.

The guid table is cached to support special QP paravirtualization, and
event propagation to slaves on guid change (we test to see if the guid
really changed before propagating an event to the slave).

To support this caching, add capability to __mlx4_ib_query_gid() to
obtain the network view (i.e., physical view) gid at index X, not just
the host (paravirtualized) view.

Based on a patch from Erez Shitrit <erezsh@mellanox.com>

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:37 -07:00
Jack Morgenstein 0a9a01884d mlx4: MAD_IFC paravirtualization
The MAD_IFC firmware command fulfills two functions.

First, it is used in the QP0/QP1 MAD-handling flow to obtain
information from the FW (for answering queries), and for setting
variables in the HCA (MAD SET packets).

For this, MAD_IFC should provide the FW (physical) view of the data.
This is the view that OpenSM needs.  We call this the "network view".

In the second case, MAD_IFC is used by various verbs to obtain data
regarding the local HCA (e.g., ib_query_device()).  We call this the
"host view".

This data needs to be paravirtualized.

MAD_IFC therefore needs a wrapper function, and also needs another
flag indicating whether it should provide the network view (when it is
called by ib_process_mad in special-qp packet handling), or the host
view (when it is called while implementing a verb).

There are currently 2 flag parameters in mlx4_MAD_IFC already:
ignore_bkey and ignore_mkey.  These two parameters are replaced by a
single "mad_ifc_flags" parameter, with different bits set for each
flag.  A third flag is added: "network-view/host-view".

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:34 -07:00
Jack Morgenstein 54679e1482 mlx4: Implement QP paravirtualization and maintain phys_pkey_cache for smp_snoop
This requires:

1. Replacing the paravirtualized P_Key index (inserted by the guest)
   with the real P_Key index.

2. For UD QPs, placing the guest's true source GID index in the
   address path structure mgid field, and setting the ud_force_mgid
   bit so that the mgid is taken from the QP context and not from the
   WQE when posting sends.

3. For UC and RC QPs, placing the guest's true source GID index in the
   address path structure mgid field.

4. For tunnel and proxy QPs, setting the Q_Key value reserved for that
   proxy/tunnel pair.

Since not all the above adjustments occur in all the QP transitions,
the QP transitions require separate wrapper functions.

Secondly, initialize the P_Key virtualization table to its default
values: Master virtualized table is 1-1 with the real P_Key table,
guest virtualized table has P_Key index 0 mapped to the real P_Key
index 0, and all the other P_Key indices mapped to the reserved
(invalid) P_Key at index 127.

Finally, add logic in smp_snoop for maintaining the phys_P_Key_cache.
and generating events on the master only if a P_Key actually changed.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:33 -07:00
Jack Morgenstein fc06573dfa IB/mlx4: Initialize SR-IOV IB support for slaves in master context
Allocate SR-IOV paravirtualization resources and MAD demuxing contexts
on the master.

This has two parts.  The first part is to initialize the structures to
contain the contexts.  This is done at master startup time in
mlx4_ib_init_sriov().

The second part is to actually create the tunneling resources required
on the master to support a slave.  This is performed the master
detects that a slave has started up (MLX4_DEV_EVENT_SLAVE_INIT event
generated when a slave initializes its comm channel).

For the master, there is no such startup event, so it creates its own
tunneling resources when it starts up.  In addition, the master also
creates the real special QPs.  The ib_core layer on the master causes
creation of proxy special QPs, since the master is also
paravirtualized at the ib_core layer.

Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <roland@purestorage.com>
2012-09-30 20:33:32 -07:00
Kleber Sacilotto de Souza 57dbf29a54 mlx4: Add support for EEH error recovery
Currently the mlx4 drivers don't have the necessary callbacks to
implement EEH errors detection and recovery, so the PCI layer uses the
probe and remove callbacks to try to recover the device after an error on
the bus. However, these callbacks have race conditions with the internal
catastrophic error recovery functions, which will also detect the error
and this can cause the system to crash if both EEH and catas functions
try to reset the device.

This patch adds the necessary error recovery callbacks and makes sure
that the internal catastrophic error functions will not try to reset the
device in such scenarios. It also adds some calls to
pci_channel_offline() to suppress reads/writes on the bus when the slot
cannot accept I/O operations so we prevent unnecessary accesses to the
bus and speed up the device removal.

Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-25 15:24:13 -07:00
Hadar Hen Zion 8fcfb4db74 net/mlx4_core: Add firmware commands to support device managed flow steering
Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.

Signed-off-by: Hadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2012-07-07 16:23:05 -07:00