Refactor the code to prepare it for supporting BWMON v5 which comes with
different register layout by:
1. Adding use of MMIO regmap and regmap fields which allows to keep one
code logic with different register maps.
2. The "clear" type registers do not allow reading, therefore regmap
requires using cache with default values.
3. regmap has an effect of introducing barriers after each readl/writel,
which should negligible effect as only few writes were relaxed.
4. Additionally usage of regmap fields removes need of shifting the
register values.
5. Add "V4" prefix to names of all defines with register addresses (so
BWMON_V4_xxx) to differentiate it from V5. The actual register values
are shared so keep their naming.
6. While changing the defines, pad register addresses to three digits
for readability.
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-8-krzysztof.kozlowski@linaro.org
Versions v4 and v5 of BWMON on SDM845 use different unit count, so allow
easier variant customization by storing its value in struct
icc_bwmon_data.
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-7-krzysztof.kozlowski@linaro.org
The hardware programming guide recommends to clear all registers on
first initialization, through separate field in BWMON_CLEAR register.
This makes sense in general but especially if driver is rebound to avoid
spurious/early interrupts.
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-6-krzysztof.kozlowski@linaro.org
Instead of copying pieces of variant-specific data (struct
icc_bwmon_data) into the state container (struct icc_bwmon), just store
a pointer to it.
This simplifies a bit the code and allows later to grow easily the
variant-specific data for new BWMON v5.
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-5-krzysztof.kozlowski@linaro.org
The interrupt enable, status and clear registers have the same layout,
so BWMON_GLOBAL_IRQ_ENABLE_ENABLE define can be used also for clearing
IRQ, instead of hard-coded value.
Cc: Rajendra Nayak <quic_rjendra@quicinc.com>
Cc: Sibi Sankar <quic_sibis@quicinc.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Sibi Sankar <quic_sibis@quicinc.com>
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220728113748.170548-3-krzysztof.kozlowski@linaro.org
This reverts commit 8239d67f59.
This change confuses the sysfs cleanup path since the rename is done
after the device registration.
Fixes: 8239d67f59 ("soc: imx: imx8m-blk-ctrl: set power device name")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
With Broadcom Broadband arch ARCH_BCMBCA supported in the kernel, this
patch series migrate the ARCH_BCM4908 symbol to ARCH_BCMBCA. Hence
replace ARCH_BCM4908 with ARCH_BCMBCA in subsystem Kconfig files.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Guenter Roeck <linux@roeck-us.net> (for watchdog)
Acked-by: Bjorn Helgaas <bhelgaas@google.com> (for drivers/pci)
Acked-by: Wolfram Sang <wsa@kernel.org> (for i2c)
Acked-by: Philipp Zabel <p.zabel@pengutronix.de> (for reset)
Link: https://lore.kernel.org/r/20220803175455.47638-7-william.zhang@broadcom.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The panic notifier of this driver is very simple code-wise, just a
memory write to a special position with some numeric code. But this
is not clear from the semantic point-of-view, and there is no public
documentation about that either.
After discussing this in the mailing-lists [0] and having Florian
explained it very well, document that in the code for the future
generations asking the same questions. Also, while at it, remove
a useless header.
[0] https://lore.kernel.org/lkml/781cafb0-8d06-8b56-907a-5175c2da196a@gmail.com
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Doug Berger <opendmb@gmail.com>
Cc: Justin Chen <justinpopo6@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Markus Mayer <mmayer@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@igalia.com>
Link: https://lore.kernel.org/r/20220719195325.402745-5-gpiccoli@igalia.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Select RENESAS_RZG2L_IRQC config option if ARCH_RZG2L is enabled
so that IRQC driver is enabled on RZ/G2L (and alike) SoC's.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20220718192824.7246-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra cpufreq driver (Viresh Kumar).
- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other users and
helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor OPP cleanups (Viresh Kumar and Yang Li).
- Add a trace event for cpuidle to track missed (too deep or too
shallow) wakeups (Kajetan Puchalski).
-----BEGIN PGP SIGNATURE-----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=LBb0
-----END PGP SIGNATURE-----
Merge tag 'pm-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are ARM cpufreq updates and operating performance points (OPP)
updates plus one cpuidle update adding a new trace point.
Specifics:
- Fix return error code in mtk_cpu_dvfs_info_init (Yang Yingliang).
- Minor cleanups and support for new boards for Qcom cpufreq drivers
(Bryan O'Donoghue, Konrad Dybcio, Pierre Gondois, and Yicong Yang).
- Fix sparse warnings for Tegra cpufreq driver (Viresh Kumar).
- Make dev_pm_opp_set_regulators() accept NULL terminated list
(Viresh Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other users and
helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they
are still in use (Liang He).
- Minor OPP cleanups (Viresh Kumar and Yang Li).
- Add a trace event for cpuidle to track missed (too deep or too
shallow) wakeups (Kajetan Puchalski)"
* tag 'pm-5.20-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (55 commits)
cpuidle: Add cpu_idle_miss trace event
venus: pm_helpers: Fix warning in OPP during probe
OPP: Don't drop opp->np reference while it is still in use
OPP: Don't drop opp_table->np reference while it is still in use
cpufreq: tegra194: Staticize struct tegra_cpufreq_soc instances
dt-bindings: cpufreq: cpufreq-qcom-hw: Add SM6375 compatible
dt-bindings: opp: Add msm8939 to the compatible list
dt-bindings: opp: Add missing compat devices
dt-bindings: opp: opp-v2-kryo-cpu: Fix example binding checks
cpufreq: Change order of online() CB and policy->cpus modification
cpufreq: qcom-hw: Remove deprecated irq_set_affinity_hint() call
cpufreq: qcom-hw: Disable LMH irq when disabling policy
cpufreq: qcom-hw: Reset cancel_throttle when policy is re-enabled
cpufreq: qcom-cpufreq-hw: use HZ_PER_KHZ macro in units.h
cpufreq: mediatek: fix error return code in mtk_cpu_dvfs_info_init()
OPP: Remove dev{m}_pm_opp_of_add_table_noclk()
PM / devfreq: tegra30: Register config_clks helper
OPP: Allow config_clks helper for single clk case
OPP: Provide a simple implementation to configure multiple clocks
OPP: Assert clk_count == 1 for single clk helpers
...
There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic
version of the MMIO accessors, which is intended to help
understand problems with device drivers and has been part
of Qualcomm's vendor kernels for many years.
- A patch from Sebastian Siewior to rework the handling of
IRQ stacks in softirqs across architectures, which is
needed for enabling PREEMPT_RT.
- The last patch to remove the CONFIG_VIRT_TO_BUS option and
some of the code behind that, after the last users of this
old interface made it in through the netdev, scsi, media and
staging trees.
-----BEGIN PGP SIGNATURE-----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=aTR0
-----END PGP SIGNATURE-----
Merge tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pull asm-generic updates from Arnd Bergmann:
"There are three independent sets of changes:
- Sai Prakash Ranjan adds tracing support to the asm-generic version
of the MMIO accessors, which is intended to help understand
problems with device drivers and has been part of Qualcomm's vendor
kernels for many years
- A patch from Sebastian Siewior to rework the handling of IRQ stacks
in softirqs across architectures, which is needed for enabling
PREEMPT_RT
- The last patch to remove the CONFIG_VIRT_TO_BUS option and some of
the code behind that, after the last users of this old interface
made it in through the netdev, scsi, media and staging trees"
* tag 'asm-generic-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic:
uapi: asm-generic: fcntl: Fix typo 'the the' in comment
arch/*/: remove CONFIG_VIRT_TO_BUS
soc: qcom: geni: Disable MMIO tracing for GENI SE
serial: qcom_geni_serial: Disable MMIO tracing for geni serial
asm-generic/io: Add logging support for MMIO accessors
KVM: arm64: Add a flag to disable MMIO trace for nVHE KVM
lib: Add register read/write tracing support
drm/meson: Fix overflow implicit truncation warnings
irqchip/tegra: Fix overflow implicit truncation warnings
coresight: etm4x: Use asm-generic IO memory barriers
arm64: io: Use asm-generic high level MMIO accessors
arch/*: Disable softirq stacks on PREEMPT_RT.
Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text. Also included in here are a few other minor updates,
2 USB files, and one Documentation file update to get the SPDX lines
correct.
All of these have been in the linux-next tree for a very long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYupz3g8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynPUgCgslaf2ssCgW5IeuXbhla+ZBRAzisAnjVgOvLN
4AKdqbiBNlFbCroQwmeQ
=v1sg
-----END PGP SIGNATURE-----
Merge tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx
Pull SPDX updates from Greg KH:
"Here is the set of SPDX comment updates for 6.0-rc1.
Nothing huge here, just a number of updated SPDX license tags and
cleanups based on the review of a number of common patterns in GPLv2
boilerplate text.
Also included in here are a few other minor updates, two USB files,
and one Documentation file update to get the SPDX lines correct.
All of these have been in the linux-next tree for a very long time"
* tag 'spdx-6.0-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/spdx: (28 commits)
Documentation: samsung-s3c24xx: Add blank line after SPDX directive
x86/crypto: Remove stray comment terminator
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_406.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_398.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_391.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_390.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_385.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_320.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_319.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_318.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_298.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_292.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_179.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 2)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_168.RULE (part 1)
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_160.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_152.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_149.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_147.RULE
treewide: Replace GPLv2 boilerplate/reference with SPDX - gpl-2.0_133.RULE
...
- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other
users/helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor cleanups (Viresh Kumar and Yang Li).
-----BEGIN PGP SIGNATURE-----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=NHBQ
-----END PGP SIGNATURE-----
Merge tag 'opp-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm
Pull operating performance points (OPP) updates for 5.20-rc1 from Viresh
Kumar:
"- Make dev_pm_opp_set_regulators() accept NULL terminated list (Viresh
Kumar).
- Add dev_pm_opp_set_config() and friends and migrate other
users/helpers to using them (Viresh Kumar).
- Add support for multiple clocks for a device (Viresh Kumar and
Krzysztof Kozlowski).
- Configure resources before adding OPP table for Venus (Stanimir
Varbanov).
- Keep reference count up for opp->np and opp_table->np while they are
still in use (Liang He).
- Minor cleanups (Viresh Kumar and Yang Li)."
* tag 'opp-updates-5.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm: (43 commits)
venus: pm_helpers: Fix warning in OPP during probe
OPP: Don't drop opp->np reference while it is still in use
OPP: Don't drop opp_table->np reference while it is still in use
OPP: Remove dev{m}_pm_opp_of_add_table_noclk()
PM / devfreq: tegra30: Register config_clks helper
OPP: Allow config_clks helper for single clk case
OPP: Provide a simple implementation to configure multiple clocks
OPP: Assert clk_count == 1 for single clk helpers
OPP: Add key specific assert() method to key finding helpers
OPP: Compare bandwidths for all paths in _opp_compare_key()
OPP: Allow multiple clocks for a device
dt-bindings: opp: accept array of frequencies
OPP: Make dev_pm_opp_set_opp() independent of frequency
OPP: Reuse _opp_compare_key() in _opp_add_static_v2()
OPP: Remove rate_not_available parameter to _opp_add()
OPP: Use consistent names for OPP table instances
OPP: Use generic key finding helpers for bandwidth key
OPP: Use generic key finding helpers for level key
OPP: Add generic key finding helpers and use them for freq APIs
OPP: Remove dev_pm_opp_find_freq_ceil_by_volt()
...
The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management
to allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and
use the firmware interfaces for system power control and for
power capping.
-----BEGIN PGP SIGNATURE-----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=0dZI
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC drivers from Arnd Bergmann:
"The SoC driver updates contain changes to improve support for
additional SoC variants, as well as cleanups an minor bugfixes
in a number of existing drivers.
Notable updates this time include:
- Support for Qualcomm MSM8909 (Snapdragon 210) in various drivers
- Updates for interconnect drivers on Qualcomm Snapdragon
- A new driver support for NMI interrupts on Fujitsu A64fx
- A rework of Broadcom BCMBCA Kconfig dependencies
- Improved support for BCM2711 (Raspberry Pi 4) power management to
allow the use of the V3D GPU
- Cleanups to the NXP guts driver
- Arm SCMI firmware driver updates to add tracing support, and use
the firmware interfaces for system power control and for power
capping"
* tag 'arm-drivers-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (125 commits)
soc: a64fx-diag: disable modular build
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: fujitsu: Add A64FX diagnostic interrupt driver
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
...
The updates for arch/arm/mach-* platform code this time are mainly
minor cleanups.
Most notably, the DaVinci DM644x/DM646x SoC support gets removed. This was
also scheduled for later removal early next year, but Linus Walleij asked
for having them removed earlier to avoid problems for the GPIO subsystem.
-----BEGIN PGP SIGNATURE-----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=LkG0
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"The updates for arch/arm/mach-* platform code this time are mainly
minor cleanups.
Most notably, the DaVinci DM644x/DM646x SoC support gets removed. This
was also scheduled for later removal early next year, but Linus
Walleij asked for having them removed earlier to avoid problems for
the GPIO subsystem"
* tag 'arm-soc-6.0' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (38 commits)
ARM: at91: setup outer cache .write_sec() callback if needed
ARM: at91: add sam_linux_is_optee_available() function
ARM: Marvell: Update PCIe fixup
ARM: bcmbca: Include full family name in Kconfig
ARM: bcm: NSP: Removed forced thermal selection
ARM: debug: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
arm: bcmbca: Add BCMBCA sub platforms
arm: bcmbca: Move BCM63138 ARCH_BCM_63XX to ARCH_BCMBCA
MAINTAINERS: Move BCM63138 to bcmbca arch entry
ARM: shmobile: rcar-gen2: Increase refcount for new reference
ARM: davinci: Delete DM646x board files
ARM: davinci: Delete DM644x board files
firmware: xilinx: Add TF_A_PM_REGISTER_SGI SMC call
cpufreq: zynq: Fix refcount leak in zynq_get_revision
ARM: OMAP2+: Kconfig: Fix indentation
ARM: OMAP2+: Fix refcount leak in omap3xxx_prm_late_init
ARM: OMAP2+: pdata-quirks: Fix refcount leak bug
ARM: OMAP2+: display: Fix refcount leak bug
ARM: OMAP2+: Fix refcount leak in omapdss_init_of
ARM: imx25: support silicon revision 1.2
...
This adds support for booting secondary cores, SPM, SMD-RPM and RPM
power-domain support for the MSM8909 platform.
It drops an unnecessary print in icc-bwmon, corrects SA8540P entries in
socinfo and a Kconfig build dependency for QCOM_RPMPD.
Lastly it continues to clean up up the Devicetree bindings for the
Qualcomm drivers.
-----BEGIN PGP SIGNATURE-----
iQJPBAABCAA5FiEEBd4DzF816k8JZtUlCx85Pw2ZrcUFAmLYinIbHGJqb3JuLmFu
ZGVyc3NvbkBsaW5hcm8ub3JnAAoJEAsfOT8Nma3FryMQANQKam+7lJrykwF3bt8t
e/ZR1SWPcKTu5dudsnA2GACnycQ8XQr5M06HRVghwveleXbjHyE3beLEy/NwfbTL
P4ufdDtg/UCwZXJ+p2ZDtbKIWQQU1qgItekYiN3lDEnb3Y5R7vI2h2mhdDOZh8yn
HtzI5EeI5gMilZ7yYtqPR3DrXpfdYBaGANshyzmP07eDTz+UyaSSKoALsy7jeWB2
9d4/inH35Tuqv/98oLaf+gK1vH89AVA13N6fVaQxgPOne3FN1bsqBFGc/RvW+phH
CG+D86lrxq7iChdEcvcoPCkabYi4lNqhbKZOiAAimqrwFCIksVJSE7adDul0JcPF
g0ml1jWIx+Jsj5TmuRH01CaxCuLtv9WKARi64vqA8dwSYuak8irP3WXbbtv/sNgW
PokJovzDwwSs71Rh8PmlXC//XY8gbsVj/umI8lEsS5/PrvdCXYsRTjRzvZ5uNtiQ
5s1fm6xMT2AMbp+Y6ZcnmPhuGntfiJZFj9GivfZuaYF44Ov6mRScHnRADC9oXpBf
7qlaC1T05PBUHOMB19xpOOsqtBpfX9TCaCqhsVxhH4bjzzYoMuV+yYlI3CqPv3yL
v9bKfMkbsOpZywCxyve2d6jqCeL8fA2iPw3MzFIlmESRA4MwdXswmxHCE3C7FOHA
SZkdXKa4EeWQRBf9g5ri3EM/
=gLQ3
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=TP2T
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
More Qualcomm driver changes for v5.20
This adds support for booting secondary cores, SPM, SMD-RPM and RPM
power-domain support for the MSM8909 platform.
It drops an unnecessary print in icc-bwmon, corrects SA8540P entries in
socinfo and a Kconfig build dependency for QCOM_RPMPD.
Lastly it continues to clean up up the Devicetree bindings for the
Qualcomm drivers.
* tag 'qcom-drivers-for-5.20-2' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
dt-bindings: soc: qcom: qcom,smd-rpm: add power-controller
dt-bindings: soc: qcom: aoss: document qcom,sm8450-aoss-qmp
dt-bindings: soc: qcom,rpmh-rsc: simplify qcom,tcs-config
ARM: mach-qcom: Add support for MSM8909
dt-bindings: arm: cpus: Document "qcom,msm8909-smp" enable-method
soc: qcom: spm: Add CPU data for MSM8909
dt-bindings: soc: qcom: spm: Add MSM8909 CPU compatible
soc: qcom: rpmpd: Add compatible for MSM8909
dt-bindings: power: qcom-rpmpd: Add MSM8909 power domains
soc: qcom: smd-rpm: Add compatible for MSM8909
dt-bindings: soc: qcom: smd-rpm: Add MSM8909
soc: qcom: icc-bwmon: Remove unnecessary print function dev_err()
soc: qcom: socinfo: Fix the id of SA8540P SoC
soc: qcom: Make QCOM_RPMPD depend on PM
Link: https://lore.kernel.org/r/20220720230648.2113609-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The NMI infrastructure cannot currently be used in loadable modules:
ERROR: modpost: "free_nmi" [drivers/soc/fujitsu/a64fx-diag.ko] undefined!
ERROR: modpost: "request_nmi" [drivers/soc/fujitsu/a64fx-diag.ko] undefined!
ERROR: modpost: "enable_nmi" [drivers/soc/fujitsu/a64fx-diag.ko] undefined!
Disable this for now to make allmodconfig build again. We may revisit
this and export those symbols instead in the future.
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add the new "qcom,rpm-msm8909" compatible to the driver so the interface
to the Resource Power Manager (RPM) is initialized correctly on MSM8909.
Signed-off-by: Stephan Gerhold <stephan.gerhold@kernkonzept.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220705143523.3390944-3-stephan.gerhold@kernkonzept.com
Eliminate the follow coccicheck warning:
./drivers/soc/qcom/icc-bwmon.c:349:2-9: line 349 is redundant because platform_get_irq() already prints an error
Fixes: b9c2ae6cac ("soc: qcom: icc-bwmon: Add bandwidth monitoring driver")
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220714075532.104665-1-yang.lee@linux.alibaba.com
Register the NMI/IRQ corresponding to the A64FX's device definition
dedicated to diagnostic interrupts, so that when this interrupt is
sent using the BMC, it causes a panic. This can be used to obtain
a kernel dump.
Signed-off-by: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Link: https://lore.kernel.org/r/20220520074119.3574753-2-hasegawa-hitomi@fujitsu.com'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Change the id of SA8540P to its correct value, i.e., 461.
Also, map the id 460 to its correct values, i.e. SA8295P.
Fixes: 76ee15ae1b ("soc: qcom: socinfo: Add some more PMICs and SoCs")
Signed-off-by: Parikshit Pareek <quic_ppareek@quicinc.com>
Reviewed-by: Eric Chanudet <echanude@redhat.com>
Tested-by: Eric Chanudet <echanude@redhat.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220711083957.12091-1-quic_ppareek@quicinc.com
QCOM_RPMPD requires PM_GENERIC_DOMAINS/_OF, which in turns requires
CONFIG_PM. I forgot about the latter in my earlier patch (it's still
in -next as of the time of committing, hence no Fixes: tag). Fix it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220707212158.32684-1-konrad.dybcio@somainline.org
This introduces a new driver that requests interconnect bandwidth based
on throughput measurements of the bwmon hardware blocks found associated
with, among other things, the CPU subsystem on many Qualcomm platforms.
It introduces support for the SCM wrapper driver to vote for
interconnect bandwidth for operations that needs bandwidth to the crypto
engine. This ensures both performance and guards against issues caused
by lacking votes for this path.
The socinfo driver gains knowledge about the SC7180P SoC.
It contains a range of fixes for spelling mistakes, refcount leaks in
various drivers and removes some redundant code from the apr remove
path.
The SCM DT bindings are updated to declare support for QCS404, SM6125
and SDX65.
The command db driver has a strncpy() converted to strscpy_pad() and
then back again with proper documentation to why this was the right API.
-----BEGIN PGP SIGNATURE-----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=AHeW
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmLN4SUACgkQmmx57+YA
GNnCRA//bthrnU+D0KiuNogJASZZWs1y+PsMHbu27JNZMCaR14+sBKiNGhkfivKt
6lqZIBSn49OCfL/SGg0E7TTZ/aMkbj+HU6aPxf6417gu1LhICOTZX81ffijwHlZu
POzvwcTWRMbIlYA/JD68y81uL2jWUpiqLXtPrzzjiEK87MR9OLEjJ/YIXciyOqaX
ao+/TW0dqHYibxWJQWb98HfuUCL0ZC9tkX3iYBu0yM2y9XJ5dVRfG6Rs++H6X83S
MIMqKbygFZ9PawzdHuPJDOv5su7PH5Sh6pUGXsxWXtAmVQESBeoRqO0KsAns8Tmi
+38olZGOuELDo4nllrPrh2fWxQKmrVolXRmwv4sq/yqgsrkXutcJdUVb2XxeiJwt
mKLDaYr1vN+YuR7XK2B2a68hFFW6a804c3cttXvp5Z4KcNNQmSiT71sILX8vqSmO
+d5URU7oSbv6c6CqTTP7aAF+sfcZiHHrRoI3IJBzUmtczNp7Eq/7cT8OZMs5eMk7
yFIIdmr4fL4MvMmYMoibL7dCOpFfVoqlveAukG9utDpziXyMzNDZ89PMmjpdU2nR
nLrwLe6NaB8h4B6GKO3HZqdiXHkP069+pKy1hOyPavp6g8qVo2JZxwQku4r0onAU
jy+KhfRGb7W7mnC/hI5UtOQwGVx9S2RkUHEyaL3QNEjAXpDOeQw=
=0Kp7
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.20
This introduces a new driver that requests interconnect bandwidth based
on throughput measurements of the bwmon hardware blocks found associated
with, among other things, the CPU subsystem on many Qualcomm platforms.
It introduces support for the SCM wrapper driver to vote for
interconnect bandwidth for operations that needs bandwidth to the crypto
engine. This ensures both performance and guards against issues caused
by lacking votes for this path.
The socinfo driver gains knowledge about the SC7180P SoC.
It contains a range of fixes for spelling mistakes, refcount leaks in
various drivers and removes some redundant code from the apr remove
path.
The SCM DT bindings are updated to declare support for QCS404, SM6125
and SDX65.
The command db driver has a strncpy() converted to strscpy_pad() and
then back again with proper documentation to why this was the right API.
* tag 'qcom-drivers-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: icc-bwmon: Add bandwidth monitoring driver
dt-bindings: interconnect: qcom,msm8998-cpu-bwmon: add BWMON device
soc/qcom: Make QCOM_RPMPD select PM_GENERIC_DOMAINS/_OF
soc: qcom: aoss: Fix refcount leak in qmp_cooling_devices_register
soc: qcom: llcc: Fix syntax errors in comments
soc: qcom: ocmem: Fix refcount leak in of_get_ocmem
dt-bindings: soc: qcom,wcnss: remove unneeded ref for names
firmware: qcom_scm: Add bw voting support to the SCM interface
dt-bindings: firmware: qcom-scm: Add interconnects property
soc: qcom: cmd-db: replace strscpy_pad() with strncpy()
dt-bindings: firmware: scm: Add compatible for SDX65
dt-bindings: arm: qcom: switch maintainer to Bjorn
soc: qcom: rpmhpd: fix typos in comment
soc: qcom: correct kerneldoc
soc: qcom: cmd-db: replace strncpy() with strscpy_pad()
firmware: qcom_scm-legacy: correct kerneldoc
dt-bindings: firmware: document Qualcomm QCS404 and SM6125 SCM
soc: qcom: apr: Drop redundant check in .remove()
firmware: qcom_scm: drop unexpected word "the"
soc: qcom: socinfo: Add an ID for sc7180P
Link: https://lore.kernel.org/r/20220712021830.1271398-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
-----BEGIN PGP SIGNATURE-----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=O/9g
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=yTZT
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom SoC drivers updatse for 5.20, please
pull the following:
- Julia fixes a typo in the Broadcom STB legacy power management code
- Liang fixes a device_node reference count leak in the Broadcom STB BIU
driver code error path(s)
- Nicolas and Stefan provide updates to the BCM2835 power management
driver allowing its use on BCM2711 (Raspberry Pi 4) and to enable the
use of the V3D GPU driver on such platforms. This is a merge of an
immutable branch from Lee Jones' MFD tree
- William removes the use of CONFIG_ARCH_BCM_63XX which is removed and
replaces the dependencies with CONFIG_ARCH_BCMBCA which is how all of
the DSL/PON SoCs from Broadcom are now supported in the upstream
kernel.
* tag 'arm-soc/for-5.20/drivers' of https://github.com/Broadcom/stblinux:
tty: serial: bcm63xx: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
spi: bcm63xx-hsspi: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
clk: bcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
hwrng: bcm2835: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
phy: brcm-sata: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
i2c: brcmstb: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
ata: ahci_brcm: bcmbca: Replace ARCH_BCM_63XX with ARCH_BCMBCA
soc: bcm: bcm2835-power: Bypass power_on/off() calls
soc: bcm: bcm2835-power: Add support for BCM2711's RPiVid ASB
soc: bcm: bcm2835-power: Resolve ASB register macros
soc: bcm: bcm2835-power: Refactor ASB control
mfd: bcm2835-pm: Add support for BCM2711
mfd: bcm2835-pm: Use 'reg-names' to get resources
soc: bcm: brcmstb: biuctrl: Add missing of_node_put()
soc: bcm: brcmstb: pm: pm-arm: fix typo in comment
Link: https://lore.kernel.org/r/20220711164451.3542127-6-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- Update imx8m-blk-ctrl driver to print the name of the power domain,
so that the error message becomes more useful.
- Update the error messages in gpcv2 driver by printing the reason why
a regulator fails to be enabled or disabled.
- A series from Michael Walle to convert the guts driver from a platform
driver to an core_initcall for getting rid of all those global static
variables.
- A couple of follow-up fixes on guts driver series.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmLJJY8UHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM54iAgAjX40h6w2DOOyVZhM6VGBHmQIzfok
MiVRjPVLsEf55brvG6IwY4KnWWCOb9bcET7JxBhYsreUsLAC8255B//mLoiLZM4x
XfCFIaQ9XxnCyfzrJuXr1K0TuwlxVYAbVghcxYFpgCSpM9GwChhQstu1dgfQE3o3
p8OXlVol3bu0NN5JkbKd2t7e9P2EoCBIb9N2JIjnlxs81W63hoKEhRkhPd2CKBIN
gKEHrMf3CFFuLpSvwKKsNzwBj2y6LML413k9l7Wp5L/MEX0+Y0G/fuQ3i2fbzoDQ
OF2SQfngaeSRy8kbp1iZ+GCqfGGoBjwinZ7v2tYElH0pheR074mxIjKntQ==
=vt6q
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=FQvj
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers change for 5.20:
- Update imx8m-blk-ctrl driver to print the name of the power domain,
so that the error message becomes more useful.
- Update the error messages in gpcv2 driver by printing the reason why
a regulator fails to be enabled or disabled.
- A series from Michael Walle to convert the guts driver from a platform
driver to an core_initcall for getting rid of all those global static
variables.
- A couple of follow-up fixes on guts driver series.
* tag 'imx-drivers-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: fsl: guts: check return value after calling of_iomap() in fsl_guts_get_soc_uid()
soc: fsl: guts: fix return value check in fsl_guts_init()
soc: imx: imx8m-blk-ctrl: Make error prints useful
soc: fsl: guts: add serial_number support
soc: fsl: guts: drop platform driver
soc: fsl: guts: use of_root instead of own reference
soc: fsl: guts: allocate soc_dev_attr on the heap
soc: fsl: guts: embed fsl_guts_get_svr() in probe()
soc: fsl: guts: remove module_exit() and fsl_guts_remove()
soc: fsl: guts: machine variable might be unset
soc: imx: gpcv2: print errno for regulator errors
Link: https://lore.kernel.org/r/20220709082951.15123-1-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- code style improvements
devapc:
- add support for MT8186
Smart Voltage Scaling (SVS)
- add support for MT8183 and MT8192
MMSYS:
- Add more display paths for MT8365
Mutex:
- Add common interface for MOD and SOF table
- Add support for MDP on MT8183
- Move binding to soc folder
- Add support to use CMDQ to enable the mutex, needed by MDP3
Power domains:
- Add support for MT6795
-----BEGIN PGP SIGNATURE-----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=VZvg
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmLNcKsACgkQmmx57+YA
GNmT6A/7BZy2sgLVuM8Z3rdvpWkuIw1LcvKs+66iAVEeZNrEOh5SWSuY1RffTMiL
8cGbenKJlmIalBQkUUVVp3dNsGIU89sExdnYSTfKNuKaZpQw1dbY+5s7w6Y72C2h
/tJ+10LnG2fUJunvdEluENBNqapy+nACazJu1sfXkTp7wD+WQO+bYv0nZrk9sAoo
YjBU42SpJUX3y7nX/ljnqIqBbyHHIeF7JUByUa5wUlMfA3DnOqlA02DkOGxDUqn+
F2e7Xozaj5P4pbxddTWX91CWfRcA77ho3R4jre2u8XZMzrClDnajQCtP+PwMssre
WdWGUo6ENiy85ZohXIl5kBzXy8CoIgjsn6M09lqaEfQh+VVjHK54Ti3KX6ziGLeI
Gfh12l2zcCtNa40L1oypsISdCDc3SSY79MXiEu8Ux1TJ7O9cmsMyjyKDCwhWixlL
DFAe1bXMIcwjjC+eOEyBHaAmWOb1xLIn4bsp/A7XzmalSzgYyiU0G8hzx73VS3Q5
MslcSVwPlHoR6G+RuFjwWJ6fcS/765E3mRN8lbaYUgO5vaJT9faFmgkH7ubOCk8g
oBV/57f4nd8+ifDqPgDwv6DJNWq8jNBtyEQ+oHSc4lj7UE+jZMor7XPKnArdtL3Q
/qMqQhTA6rCsXUij6ayKBg3IGia7M13ffP30WerMc8TOixUjQvY=
=KbI7
-----END PGP SIGNATURE-----
Merge tag 'v5.19-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/drivers
pmic wrapper:
- code style improvements
devapc:
- add support for MT8186
Smart Voltage Scaling (SVS)
- add support for MT8183 and MT8192
MMSYS:
- Add more display paths for MT8365
Mutex:
- Add common interface for MOD and SOF table
- Add support for MDP on MT8183
- Move binding to soc folder
- Add support to use CMDQ to enable the mutex, needed by MDP3
Power domains:
- Add support for MT6795
* tag 'v5.19-next-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux: (29 commits)
soc: mediatek: mutex: Simplify with devm_platform_get_and_ioremap_resource()
soc: mediatek: pm-domains: Add support for Helio X10 MT6795
dt-bindings: power: Add MediaTek Helio X10 MT6795 power domains
soc: mediatek: SVS: Use DEFINE_SIMPLE_DEV_PM_OPS for svs_pm_ops
soc: mediatek: mtk-pm-domains: Allow probing vreg supply on two MFGs
soc: mediatek: fix missing clk_disable_unprepare() on err in svs_resume()
soc: mediatek: mutex: Use DDP_COMPONENT_DITHER0 mod index for MT8365
soc: mediatek: mutex: add functions that operate registers by CMDQ
dt-bindings: soc: mediatek: add gce-client-reg for MUTEX
dt-bindings: soc: mediatek: move out common module from display folder
soc: mediatek: mutex: add 8183 MUTEX MOD settings for MDP
soc: mediatek: mutex: add common interface for modules setting
soc: mediatek: pm-domains: Add support always on flag
soc: mediatek: mt8365-mmsys: add DPI/HDMI display path
soc: mediatek: mutex: add MT8365 support
soc: mediatek: SVS: add mt8192 SVS GPU driver
dt-bindings: soc: mediatek: add mt8192 svs dt-bindings
soc: mediatek: SVS: add debug commands
soc: mediatek: SVS: add monitor mode
soc: mediatek: SVS: introduce MTK SVS engine
...
Link: https://lore.kernel.org/r/b733bd82-6d99-23ef-0541-98e98eb8d3bc@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Convert platform_get_resource(), devm_ioremap_resource() to a single
call to devm_platform_get_and_ioremap_resource(), as this is exactly
what this function does.
While at it, also remove a redundant call to of_address_to_resource(),
as this was getting the address of the same resource index 0: we can
as well get the iostart from the 'regs' pointer.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220623121701.107512-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The OPP core now provides a unified API for setting all configuration
types, i.e. dev_pm_opp_set_config().
Lets start using it.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Explain why special handling was required here, it isn't obvious at all.
Tested-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Make dev_pm_opp_set_regulators() accept a NULL terminated list of names
instead of making the callers keep the two parameters in sync, which
creates an opportunity for bugs to get in.
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Steven Price <steven.price@arm.com> # panfrost
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
When building this driver for an architecture that does not support
CONFIG_PM_SLEEP, such as hexagon, the following warnings occur:
drivers/soc/mediatek/mtk-svs.c:1481:12: error: unused function 'svs_suspend' [-Werror,-Wunused-function]
static int svs_suspend(struct device *dev)
^
drivers/soc/mediatek/mtk-svs.c:1515:12: error: unused function 'svs_resume' [-Werror,-Wunused-function]
static int svs_resume(struct device *dev)
^
2 errors generated.
This happens because SIMPLE_DEV_PM_OPS uses SET_SYSTEM_SLEEP_PM_OPS,
which evaluates to nothing when CONFIG_PM_SLEEP is not set, leaving the
functions unused in the eyes of the compiler.
This problem was rectified in commit 1a3c7bb088 ("PM: core: Add new
*_PM_OPS macros, deprecate old ones") with new macros. Use
DEFINE_SIMPLE_DEV_PM_OPS to fix the warning while not changing
svs_pm_ops when CONFIG_PM_SLEEP is set.
Fixes: 681a02e950 ("soc: mediatek: SVS: introduce MTK SVS engine")
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Link: https://lore.kernel.org/r/20220622175649.1856337-1-nathan@kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
MediaTek SoCs have multiple MFG power-domains, exclusively used for
the GPU which, in turn, requires external power supplies: make sure
to have the MTK_SCPD_DOMAIN_SUPPLY cap on the two topmost MFGs to
allow voting for regulators on/off upon usage of these power domains.
This also ensures that the SRAM is actually powered and that we're
not relying on the bootloader leaving this supply on when performing
the first (and latter) poweron sequence for these domains' sram.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220623123850.110225-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The K3 AM62x family of SoC has one PRUSS-M instance and it has two
Programmable Real-Time Units (PRU0 and PRU1). This does not support
Industrial Communications Subsystem features like Ethernet.
The existing pruss platform driver has been updated to support this
through a new AM62x specific compatible.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220602120613.2175-4-kishon@ti.com
Bandwidth monitoring (BWMON) sits between various subsytems like CPU,
GPU, Last Level caches and memory subsystem. The BWMON can be
configured to monitor the data throuhput between memory and other
subsytems. The throughput is measured within specified sampling window
and is used to vote for corresponding interconnect bandwidth.
Current implementation brings support for BWMON v4, used for example on
SDM845 to measure bandwidth between CPU (gladiator_noc) and Last Level
Cache (memnoc). Usage of this BWMON allows to remove fixed bandwidth
votes from cpufreq (CPU nodes) thus achieve high memory throughput even
with lower CPU frequencies.
The driver was tested on SDM845.
Co-developed-by: Thara Gopinath <thara.gopinath@gmail.com>
Signed-off-by: Thara Gopinath <thara.gopinath@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220704121730.127925-3-krzysztof.kozlowski@linaro.org
This driver exists as a workaround for old devicetrees which are missing
interconnects properties, so it is only useful for those specific
platforms, which all happen to be ARM or ARM64.
This solves the issue that the driver fails to build on RISC-V, where
PHYS_OFFSET is not defined.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220702032520.22129-1-samuel@sholland.org
The driver uses generic genpd OF APIs and with a very minimal config
where nothing else selects them, this driver will not probe, as
of_genpd_add_provider_onecell will return -EOPNOTSUPP.
Make sure to select these in Kconfig to prevent that.
Signed-off-by: Konrad Dybcio <konrad.dybcio@somainline.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220701073700.17124-1-konrad.dybcio@somainline.org
of_iomap() may return NULL, so we need check the return value.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In case of error, of_iomap() returns NULL pointer not ERR_PTR().
The IS_ERR() test in the return value check should be replaced
with NULL test and return -ENOMEM as error value.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When compiling with -Wformat, clang emits the following warnings:
drivers/soc/qcom/smem.c:847:41: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
dev_err(smem->dev, "bad host %hu\n", remote_host);
~~~ ^~~~~~~~~~~
%u
./include/linux/dev_printk.h:144:65: note: expanded from macro 'dev_err'
dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
drivers/soc/qcom/smem.c:852:47: warning: format specifies type 'unsigned
short' but the argument has type 'unsigned int' [-Wformat]
dev_err(smem->dev, "duplicate host %hu\n", remote_host);
~~~ ^~~~~~~~~~~
%u
./include/linux/dev_printk.h:144:65: note: expanded from macro 'dev_err'
dev_printk_index_wrap(_dev_err, KERN_ERR, dev, dev_fmt(fmt), ##__VA_ARGS__)
~~~ ^~~~~~~~~~~
./include/linux/dev_printk.h:110:23: note: expanded from macro 'dev_printk_index_wrap'
_p_func(dev, fmt, ##__VA_ARGS__); \
~~~ ^~~~~~~~~~~
The types of these arguments are unconditionally defined, so this patch
updates the format character to the correct one and change type of
remote_host to "u16" to match with other types.
Signed-off-by: Bill Wendling <morbo@google.com>
Tested-by: Justin Stitt <jstitt007@gmail.com>
Reviewed-by: Justin Stitt <jstitt007@gmail.com>
Link: https://github.com/ClangBuiltLinux/linux/issues/378
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Bypass power_on/power_off() when running on BCM2711 as they are not
needed.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-12-stefan.wahren@i2se.com
In BCM2711 the new RPiVid ASB took over V3D. The old ASB is still present
with the ISP and H264 bits, and V3D is in the same place in the new ASB
as the old one.
Use the fact that 'pm->rpivid_asb' is populated as a hint that we're on
BCM2711.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-11-stefan.wahren@i2se.com
The macros in order to access the ASB registers have a hard coded base
address. So extending them for other platforms would make them harder
to read. As a solution resolve these macros.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-10-stefan.wahren@i2se.com
The functions to control the async AXI bridges are almost identical.
So define a general function to handle it and keep the original ones as
wrapper. This should make this driver easier to extend.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-9-stefan.wahren@i2se.com
The kernel test robot found this inconsistency:
drivers/soc/ixp4xx/ixp4xx-npe.c:737:34: warning:
'ixp4xx_npe_of_match' defined but not used [-Wunused-const-variable=]
737 | static const struct of_device_id ixp4xx_npe_of_match[] = {
This is because the match is enclosed in the of_match_ptr()
which compiles into NULL when OF is disabled and this
is unnecessary.
Fix it by dropping of_match_ptr() around the match.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220626074315.61209-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Every iteration of for_each_available_child_of_node() decrements
the reference count of the previous node.
When breaking early from a for_each_available_child_of_node() loop,
we need to explicitly call of_node_put() on the child node.
Add missing of_node_put() to avoid refcount leak.
Fixes: 05589b30b2 ("soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220606064252.42595-1-linmq006@gmail.com
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
of_node_put() will check NULL pointer.
Fixes: 88c1e9404f ("soc: qcom: add OCMEM driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220602042430.1114-1-linmq006@gmail.com
SGI interrupt register and reset is performed by EEMI ioctl
IOCTL_REGISTER_SGI. However, this is not correct use of EEMI call.
SGI registration functionality does not qualify as energy management
activity and so shouldn't be mapped to EEMI call.
This new call will replace IOCTL_REGISTER_SGI and will be handled by TF-A
specific handler in TF-A. To maintain backward compatibility for a while
firmware driver will still use IOCTL_REGISTER_SGI as fallback strategy if
new call fails or is not supported by TF-A.
This new design also helps to make TF-A as pass through layer for EEMI
calls. So we don't have to maintain PM_IOCTL as EEMI API ID in TF-A.
Signed-off-by: Tanmay Shah <tanmay.shah@xilinx.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220607224253.54919-1-tanmay.shah@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit ac0126a017 ("soc: qcom: cmd-db: replace strncpy() with
strscpy_pad()") breaks booting on my sc7280-herobrine-herobrine
device. From printouts I see that at bootup the function is called
with an id of "lnbclka2" which is 8 bytes big.
Previously all 8 bytes of this string were copied to the
destination. Now only 7 bytes will be copied since strscpy_pad() saves
a byte for '\0' termination.
We don't need the '\0' termination in the destination. Let's go back
to strncpy(). According to the warning:
If a caller is using non-NUL-terminated strings, strncpy() can still
be used, but destinations should be marked with the __nonstring
attribute to avoid future compiler warnings.
...so we'll do that.
While we're at it, let's change the query array to use
"sizeof(ent->id)" so it can't possibly go out of sync with our later
copy.
Fixes: ac0126a017 ("soc: qcom: cmd-db: replace strncpy() with strscpy_pad()")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220628064301.v3.1.Ie7b480cd99e2c13319220cbc108caf2bcd41286b@changeid
Print the name of the power domain which failed to make the error
prints actually useful for finding the error.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexander Stein <alexander.stein@ew.tq-group.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Martyn Welch <martyn.welch@collabora.com>
Cc: Paul Elder <paul.elder@ideasonboard.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Most layerscapes provide a security fuse processor where the vendor
will store a unique id per part. Unfortunately, we cannot use the
corresponding efuse driver because this driver needs to be ready
early during the boot phase. To get the unique identifier, we just
need to access two registers. Thus we just search the device tree
for the corresponding device, map its memory to read the id and then
unmap it again.
Because it is likely that the offset within the fuses is dependent
on the SoC, we need a per SoC data. Also, the compatible string is
different among the SoCs. For now, this add support for the LS1028A
SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This driver cannot be unloaded and it will be needed very early in the
boot process because other driver (weakly) depend on it (eg. for chip
errata handling). Drop all the platform driver and devres stuff and
simply make it a core_initcall.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is already a global of_root reference. Use that instead of getting
one on our own. We don't need to care about the reference count either
this way.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the last global static variable. Drop it and allocate the memory
on the heap instead.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move the reading of the SVR into the probe function as
fsl_guts_get_svr() is the only user of the static guts variable and this
lets us drop that as well as the malloc() for this variable. Also, we
can unmap the memory region after we accessed it, which will simplify
error handling later.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This driver will never be unloaded. Firstly, it is not available as a
module, but more importantly, other drivers will depend on this one to
apply possible chip errata.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
If both the model and the compatible properties are missing, then
machine will not be set. Initialize it with NULL.
Fixes: 34c1c21e94 ("soc: fsl: fix section mismatch build warnings")
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct kerneldoc warnings like:
drivers/soc/qcom/mdt_loader.c:126:
warning: Function parameter or member 'fw_name' not described in 'qcom_mdt_read_metadata'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220519073301.7072-2-krzysztof.kozlowski@linaro.org
The use of strncpy() is considered deprecated for NUL-terminated
strings[1]. Replace strncpy() with strscpy_pad(), to keep existing
pad-behavior of strncpy. This fixes W=1 warning:
drivers/soc/qcom/cmd-db.c: In function ‘cmd_db_get_header.part.0’:
drivers/soc/qcom/cmd-db.c:151:9: warning: ‘strncpy’ specified bound 8 equals destination size [-Wstringop-truncation]
151 | strncpy(query, id, sizeof(query));
[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220519073301.7072-1-krzysztof.kozlowski@linaro.org
The remove callback is only called by the driver core if there is a
driver to unbind, so there is no need to check dev->driver to be
non-NULL.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220618203913.35785-1-u.kleine-koenig@pengutronix.de
Some sc7180 Chromebooks actually have sc7180P (known by many names,
apparently, including possibly sc7180 Pro and sc7185). This is a
sc7180 part that has slightly higher clock speeds.
The official ID number allocated to these devices by Qualcomm is 495
so we'll add an entry to the table for them. Note that currently
shipping BIOS for these devices will actually end up reporting an ID
of 407 due to a bug but eventually a new BIOS will be released which
corrects it to 495.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220523085437.v3.1.I26eca1856f99e6160d30de6d50ecab60e6226354@changeid
Fix the missing clk_disable_unprepare() before return
from svs_resume() in the error handling case.
Signed-off-by: Peng Wu <wupeng58@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Link: https://lore.kernel.org/r/20220623070240.63382-1-wupeng58@huawei.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In commit
4e8988c634 ("soc: mediatek: add DDP_DOMPONENT_DITHER0 enum for mt8195 vdosys0")
the enum mtk_ddp_comp_id was modified to add an index number to the
DITHER component because some new SoCs have multiple dither blocks.
As a result, all of the mutex mod arrays have been changed to use the
new definition instead of the old one (even if that's retained): for
consistency purposes, follow the same trend on the newly introduced
MT8365 mutex mod array.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220620102454.131417-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Make debugging of power management issues easier by printing the reason
why a regulator fails to be enabled or disabled.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In brcmstb_biuctrl_init(), of_find_compatible_node() will return a
node pointer with refcount incremented. We should use of_node_put()
in each fail path or when it is not used anymore.
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Due to HW limitations, MDP3 is necessary to enable MUTEX in each frame
for SOF triggering and cooperate with CMDQ control to reduce the amount
of interrupts generated(also, reduce frame latency).
In response to the above situation, a new interface
"mtk_mutex_enable_by_cmdq" has been added to achieve the purpose.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220610063424.7800-7-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
For the purpose of module independence, related settings should be moved
from MDP to the corresponding driver.
This patch adds 8183 MUTEX MOD settings for MDP.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220610063424.7800-3-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to allow multiple modules to operate MUTEX hardware through
a common interfrace, two flexible indexes "mtk_mutex_mod_index" and
"mtk_mutex_sof_index" need to be added to replace original component
ID so that like DDP and MDP can add their own MOD table or SOF
settings independently.
In addition, 2 generic interface "mtk_mutex_write_mod" and
"mtk_mutex_write_sof" have been added, which is expected to replace
the "mtk_mutex_add_comp" and "mtk_mutex_remove_comp" pair originally
dedicated to DDP in the future.
Signed-off-by: Moudy Ho <moudy.ho@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220610063424.7800-2-moudy.ho@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There is a t-phy shared by PCIe and USB3 on mt8195, if the t-phy is
used by PCIe, when power off its mtcmos, need software reset it
(workaround way, usually hardware do it, but has an issue on mt8195),
but it has side effect to USB2 phy(works with USB3 phy to support
USB3.2 Gen1), so add support GENPD_FLAG_ALWAYS_ON flag, and make its
power always on.
Another reason is that USB3.2 Gen1/2 need keep power always on when
support runtime-pm due to hardware limitation until now.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220617095841.23031-1-chunfeng.yun@mediatek.com
[mb: smaller nit fixes on commit message]
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Right now only the DSI path connections are described in the mt8365
mmsys driver. The external path will be DPI/HDMI. This commit adds
the connections for DPI/HDMI.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Link: https://lore.kernel.org/r/20220530201436.902505-5-fparent@baylibre.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
mt8192 SVS GPU uses 2-line (high/low bank) HW architecture to provide
bank voltages. High bank helps update higher frequency's voltage
and low bank helps update lower frequency's voltage.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-8-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The purpose of SVS is to help find the suitable voltages
for DVFS. Therefore, if SVS bank voltages are concerned
to be wrong, we can show/disable SVS bank voltages by
this patch.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-6-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
SVS monitor mode is based on different thermal temperature
to provide suitable SVS bank voltages.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-5-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The Smart Voltage Scaling(SVS) engine is a piece of hardware
which calculates suitable SVS bank voltages to OPP voltage table.
Then, DVFS driver could apply those SVS bank voltages to PMIC/Buck
when receiving OPP_EVENT_ADJUST_VOLTAGE.
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20220516004311.18358-4-roger.lu@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In meson_secure_pwrc_probe(), there is a refcount leak in one fail
path.
Signed-off-by: Liang He <windhl@126.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: b3dde5013e ("soc: amlogic: Add support for Secure power domains controller")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220616144915.3988071-1-windhl@126.com
Disable MMIO tracing for GENI SE driver to prevent excessive
logging. Any access over serial console would involve a lot of
TX and RX register accesses (and few others), so these MMIO
read/write trace events in these drivers cause a lot of unwanted
noise because of the high frequency of such operations and it is
not very useful tracing these events for such drivers.
Given we want to enable these trace events on development devices
(maybe not production devices) where performance also really
matters so that we don't regress other components by wasting CPU
cycles and memory collecting these traces, it makes more sense to
disable these traces from such drivers.
Also another reason to disable these traces would be to prevent
recursive tracing when we display the trace buffer containing
these MMIO trace events since writing onto serial console would
further record MMIO traces.
Signed-off-by: Sai Prakash Ranjan <quic_saipraka@quicinc.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
LCDIF2 has its own display clock, use this one.
Fixes: 07614fed00 ("soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl")
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Paul Elder <paul.elder@ideasonboard.com>
Tested-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Reduce the sizes of the rcar_sysc_area and rcar_gen4_sysc_area
structures:
- parent is in the range [-1..32] or [-1..64], so s8 is sufficient,
- flags needs just 3 bits (for now), so u8 is plenty.
This reduces kernel size by:
- 288 bytes for an R-Car Gen1+Gen2 kernel (arm32),
- 1772 bytes for an R-Car Gen3+Gen4 kernel (arm64).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/cbbc8f464743d636895c048de61aa610d75392de.1654701156.git.geert+renesas@glider.be
The PDR values for the A2DP1 and A2CV[2357] power areas on R-Car V3U are
incorrect (copied-and-pasted from A2DP0 and A2CV[0146]).
Fix them.
Reported-by: Renesas Vietnam via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 1b4298f000 ("soc: renesas: r8a779a0-sysc: Add r8a779a0 support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/87bc2e70ba4082970cf8c65871beae4be3503189.1654696188.git.geert+renesas@glider.be
Based on the normalized pattern:
this program is free software you can redistribute it and/or modify it
under the terms of the gnu general public license as published by the
free software foundation version 2 this program is distributed as is
without any warranty of any kind whether express or implied without
even the implied warranty of merchantability or fitness for a
particular purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference.
Reviewed-by: Allison Randal <allison@lohutok.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
In brcmstb_init_sram, it pass dn to of_address_to_resource(),
of_address_to_resource() will call of_find_device_by_node() to take
reference, so we should release the reference returned by
of_find_matching_node().
Fixes: 0b741b8234 ("soc: bcm: brcmstb: Add support for S2/S3/S5 suspend states (ARM)")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Spelling mistake (triple letters) in comment.
Detected with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The register offsets is the same between MT6779 and MT8186. To reuse the
register offsets, we move these register offsets to another structure
"mtk_devapc_regs_ofs".
Signed-off-by: Rex-BC Chen <rex-bc.chen@mediatek.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://lore.kernel.org/r/20220504115501.3490-3-rex-bc.chen@mediatek.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Compress each entry of the of_device_id tables in this driver to one
line instead of three, as they fit just fine in a single line.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220517104712.24579-6-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In the PMIC Wrapper driver each PMIC has its own regmap configuration
and its own pwrap_{read/write}() callbacks, but it's just about either
a 32 bits vs 16 bits register, and only one of them uses 32bits regs:
this means that the same ops are assigned over and over again to all
of the supported PMICs.
It is therefore possible to avoid reassigning the same things over
and over, reducing the amount of lines, without any impact on human
readability of this driver: add a pwrap_slv_regops structure and
move the callbacks and regmap_config pointer in there instead.
This allows to assign just one pointer to that shared data in the
per-pmic struct pwrap_slv_type.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220517104712.24579-5-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Check for the return value of platform_get_irq(): if no interrupt
is specified, it wouldn't make sense to call devm_request_irq().
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220517104712.24579-4-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
In order to simplify ioremapping resources, instead of calling
platform_get_resource_byname() and then devm_ioremap_resource(),
simply call devm_platform_ioremap_resource_byname().
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220517104712.24579-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Function pwrap_wait_for_state() is a function that polls an address
through a helper function, but this is the very same operation that
the readx_poll_timeout macro means to do.
Convert all instances of calling pwrap_wait_for_state() to instead
use the read_poll_timeout macro.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Tested-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Link: https://lore.kernel.org/r/20220517104712.24579-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
This is the second part of the general SoC updates, containing
everything that did not make it in the initial pull request,
or that came in as a bugfix later.
- Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip, including
a new machine using an ASPEED BMC.
- More DT fixes from Krzysztof Kozlowski across platforms
- A new SoC platform for the GXP baseboard management controller,
used in current server products from HPE.
-----BEGIN PGP SIGNATURE-----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=2qok
-----END PGP SIGNATURE-----
Merge tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM SoC updates from Arnd Bergmann:
"This is the second part of the general SoC updates, containing
everything that did not make it in the initial pull request, or that
came in as a bugfix later.
- Devicetree updates for SoCFPGA, ASPEED, AT91 and Rockchip,
including a new machine using an ASPEED BMC.
- More DT fixes from Krzysztof Kozlowski across platforms
- A new SoC platform for the GXP baseboard management controller,
used in current server products from HPE"
* tag 'arm-late-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (56 commits)
ARM: configs: Enable more audio support for i.MX
tee: optee: Pass a pointer to virt_addr_valid()
arm64: dts: rockchip: rename Quartz64-A bluetooth gpios
arm64: dts: rockchip: add clocks property to cru node rk3368
arm64: dts: rockchip: add clocks property to cru node rk3308
arm64: dts: rockchip: add clocks to rk356x cru
ARM: dts: rockchip: add clocks property to cru node rk3228
ARM: dts: rockchip: add clocks property to cru node rk3036
ARM: dts: rockchip: add clocks property to cru node rk3066a/rk3188
ARM: dts: rockchip: add clocks property to cru node rk3288
ARM: dts: rockchip: Remove "amba" bus nodes from rv1108
ARM: dts: rockchip: add clocks property to cru node rv1108
arm64: dts: sprd: use new 'dma-channels' property
ARM: dts: da850: use new 'dma-channels' property
ARM: dts: pxa: use new 'dma-channels/requests' properties
soc: ixp4xx/qmgr: Fix unused match warning
ARM: ep93xx: Make ts72xx_register_flash() static
ARM: configs: enable support for Kontron KSwitch D10
ep93xx: clock: Do not return the address of the freed memory
arm64: dts: intel: add device tree for n6000
...
The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went through
several rebases before the merge window as bugs were found, so they
remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files.
-----BEGIN PGP SIGNATURE-----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=cnSb
-----END PGP SIGNATURE-----
Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull more ARM multiplatform updates from Arnd Bergmann:
"The second part of the multiplatform changes now converts the
Intel/Marvell PXA platform along with the rest. The patches went
through several rebases before the merge window as bugs were found, so
they remained separate.
This has to touch a lot of drivers, in particular the touchscreen,
pcmcia, sound and clk bits, to detach the driver files from the
platform and board specific header files"
* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
ARM: pxa/mmp: remove traces of plat-pxa
ARM: pxa: convert to multiplatform
ARM: pxa/sa1100: move I/O space to PCI_IOBASE
ARM: pxa: remove support for MTD_XIP
ARM: pxa: move mach/*.h to mach-pxa/
ARM: PXA: fix multi-cpu build of xsc3
ARM: pxa: move plat-pxa to drivers/soc/
ARM: mmp: rename pxa_register_device
ARM: mmp: remove tavorevb board support
ARM: pxa: remove unused mach/bitfield.h
ARM: pxa: move clk register definitions to driver
ARM: pxa: move smemc register access from clk to platform
cpufreq: pxa3: move clk register access to clk driver
ARM: pxa: remove get_clk_frequency_khz()
ARM: pxa: pcmcia: move smemc configuration back to arch
ASoC: pxa: i2s: use normal MMIO accessors
ASoC: pxa: ac97: use normal MMIO accessors
ASoC: pxa: use pdev resource for FIFO regs
Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
Input: wm97xx - switch to using threaded IRQ
...
- Add Tegra234 cpufreq support (Sumit Gupta).
- Clean up and enhance the Mediatek cpufreq driver (Wan Jiabing,
Rex-BC Chen, and Jia-Wei Chang).
- Fix up the CPPC cpufreq driver after recent changes (Zheng Bin,
Pierre Gondois).
- Minor update to dt-binding for Qcom's opp-v2-kryo-cpu (Yassine
Oudjana).
- Use list iterator only inside the list_for_each_entry loop (Xiaomeng
Tong, and Jakob Koschel).
- New APIs related to finding OPP based on interconnect bandwidth
(Krzysztof Kozlowski).
- Fix the missing of_node_put() in _bandwidth_supported() (Dan
Carpenter).
- Cleanups (Krzysztof Kozlowski, and Viresh Kumar).
- Add Out of Band mode description to the intel-speed-select utility
documentation (Srinivas Pandruvada).
- Add power sequences support to the system reboot and power off
code and make related platform-specific changes for multiple
platforms (Dmitry Osipenko, Geert Uytterhoeven).
-----BEGIN PGP SIGNATURE-----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=PAh+
-----END PGP SIGNATURE-----
Merge tag 'pm-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These update the ARM cpufreq drivers and fix up the CPPC cpufreq
driver after recent changes, update the OPP code and PM documentation
and add power sequences support to the system reboot and power off
code.
Specifics:
- Add Tegra234 cpufreq support (Sumit Gupta)
- Clean up and enhance the Mediatek cpufreq driver (Wan Jiabing,
Rex-BC Chen, and Jia-Wei Chang)
- Fix up the CPPC cpufreq driver after recent changes (Zheng Bin,
Pierre Gondois)
- Minor update to dt-binding for Qcom's opp-v2-kryo-cpu (Yassine
Oudjana)
- Use list iterator only inside the list_for_each_entry loop
(Xiaomeng Tong, and Jakob Koschel)
- New APIs related to finding OPP based on interconnect bandwidth
(Krzysztof Kozlowski)
- Fix the missing of_node_put() in _bandwidth_supported() (Dan
Carpenter)
- Cleanups (Krzysztof Kozlowski, and Viresh Kumar)
- Add Out of Band mode description to the intel-speed-select utility
documentation (Srinivas Pandruvada)
- Add power sequences support to the system reboot and power off code
and make related platform-specific changes for multiple platforms
(Dmitry Osipenko, Geert Uytterhoeven)"
* tag 'pm-5.19-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (60 commits)
cpufreq: CPPC: Fix unused-function warning
cpufreq: CPPC: Fix build error without CONFIG_ACPI_CPPC_CPUFREQ_FIE
Documentation: admin-guide: PM: Add Out of Band mode
kernel/reboot: Change registration order of legacy power-off handler
m68k: virt: Switch to new sys-off handler API
kernel/reboot: Add devm_register_restart_handler()
kernel/reboot: Add devm_register_power_off_handler()
soc/tegra: pmc: Use sys-off handler API to power off Nexus 7 properly
reboot: Remove pm_power_off_prepare()
regulator: pfuze100: Use devm_register_sys_off_handler()
ACPI: power: Switch to sys-off handler API
memory: emif: Use kernel_can_power_off()
mips: Use do_kernel_power_off()
ia64: Use do_kernel_power_off()
x86: Use do_kernel_power_off()
sh: Use do_kernel_power_off()
m68k: Switch to new sys-off handler API
powerpc: Use do_kernel_power_off()
xen/x86: Use do_kernel_power_off()
parisc: Use do_kernel_power_off()
...
The kernel test robot found this inconsistency:
>> drivers/soc/ixp4xx/ixp4xx-npe.c:737:34: warning:
'ixp4xx_npe_of_match' defined but not used [-Wunused-const-variable=]
737 | static const struct of_device_id ixp4xx_npe_of_match[] = {
This is because the match is enclosed in the of_match_ptr()
which compiles into NULL when OF is disabled and this
is unnecessary.
Fix it by dropping of_match_ptr() around the match.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20220523085520.913217-1-linus.walleij@linaro.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom. Noteworthy
driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree,
we have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an optimization,
and SCMI now supports the 3.1 version of the specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI drivers
- Memory controller updates for Tegra, and a few updates for other
platforms.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmKOXOoACgkQmmx57+YA
GNlpVQ//eQGfL0WktE5G/y0mCVuVHtXT5nSjHMgjTOdb9+QvaATCfxnLXvP7Gq7C
7YzJd68G+2ZC4rUkkjTxyMICT7eIrJSAIAFn4PWee4EQ5DfbHgG+1tToTjxqb+QQ
6wGB5MVaYUhjZE30kY2E8a+OKxHtEnkt9wcch6ei0vzsMZquQJF6byfHd5+I4Knd
CyDmXX8ZGXK3FnhvuBLr3Rgwyhs0X4Ju7UaONLZxBYxdnh8WmymRszmMnv5qEkub
KDe8fbhFamOT3Z55JdCA5xq7LvUzjsKpTGFxFcS0ptbkTmtAsuyYqqiWvAPx3D5u
5TxVGSx9QKid6fpIsITZ2ptO6fgljh1W9b/3Y3/eltudXsM1qqSxyN2Hre+M9egf
WEDADqbNR5Y5+bq1iZWI348jXkNHVPpsLHI9Ihqf4yyrKwFkmRmNLnws53XTAPH2
FPXZvJjwFDBDHGfewSoLFePXUPNytVLXbr6Mq72ZyTDIBDU8Mxh666Wd8bu4tgbG
1Y2pMjDIdXDOsljM6Of5D3XjM1kuDwEmFxWGy+cKLgoEbHLeE1xIbTjUir4687+d
VNHdtsIRFPRZzz2lUSmI8vlA2aewMWrkOF/Ulz8xh6gG8uitMSfOxghg4IWOfRVM
mlvgFP5eqTInmQcbWRxaRO9JzP+rPp1sAcEpsBmuEHw5Akflbc8=
=XoLF
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM driver updates from Arnd Bergmann:
"There are minor updates to SoC specific drivers for chips by Rockchip,
Samsung, NVIDIA, TI, NXP, i.MX, Qualcomm, and Broadcom.
Noteworthy driver changes include:
- Several conversions of DT bindings to yaml format.
- Renesas adds driver support for R-Car V4H, RZ/V2M and RZ/G2UL SoCs.
- Qualcomm adds a bus driver for the SSC (Snapdragon Sensor Core),
and support for more chips in the RPMh power domains and the
soc-id.
- NXP has a new driver for the HDMI blk-ctrl on i.MX8MP.
- Apple M1 gains support for the on-chip NVMe controller, making it
possible to finally use the internal disks. This also includes SoC
drivers for their RTKit IPC and for the SART DMA address filter.
For other subsystems that merge their drivers through the SoC tree, we
have
- Firmware drivers for the ARM firmware stack including TEE, OP-TEE,
SCMI and FF-A get a number of smaller updates and cleanups. OP-TEE
now has a cache for firmware argument structures as an
optimization, and SCMI now supports the 3.1 version of the
specification.
- Reset controller updates to Amlogic, ASpeed, Renesas and ACPI
drivers
- Memory controller updates for Tegra, and a few updates for other
platforms"
* tag 'arm-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (159 commits)
memory: tegra: Add MC error logging on Tegra186 onward
memory: tegra: Add memory controller channels support
memory: tegra: Add APE memory clients for Tegra234
memory: tegra: Add Tegra234 support
nvme-apple: fix sparse endianess warnings
soc/tegra: pmc: Document core domain fields
soc: qcom: pdr: use static for servreg_* variables
soc: imx: fix semicolon.cocci warnings
soc: renesas: R-Car V3U is R-Car Gen4
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
soc: imx: imx8m-blk-ctrl: set power device name
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc/tegra: pmc: Select REGMAP
dt-bindings: reset: st,sti-powerdown: Convert to yaml
dt-bindings: reset: st,sti-picophyreset: Convert to yaml
dt-bindings: reset: socfpga: Convert to yaml
dt-bindings: reset: snps,axs10x-reset: Convert to yaml
...
These updates are for platform specific code in arch/arm/, mostly fixing
minor issues. The at91 platform gains support for better power
management on the lan966 platform and new firmware on the sama5
platform. The mediatek soc drivers in turn are enabled for the new
mt8195 SoC.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmKORHMACgkQmmx57+YA
GNnKYA//QhTTZePOMqHZHBVU4dqJuHrjd+rwME5u7a6hqSe3VYaFao6LF+P5fAzR
IWk8svgCJLIdRx4tnA+kE7LIBsJoPwXYxhGUlgM5CfrxYClQuofnWP58Z+EbIAXx
VIboLBW1Anw5y7zw+0JkB01DMuGzDDFnUJ4Y+0M3aW3VGC8wJXc+dM+t8BWOn7OW
DNTcXfJgkRJBtzT++tMU4Z7Kmn//i4xohuT7dwJW4vvIfTL350Bl5Z1EHGnScfMk
HgbJD5iF7Z12jj7ureuWengr/MN1eAPs18ZdWRcmo4Ie5IDWB50dMoYifjp/tslO
oXRODrGCuX9yOjcjleGU1mAbb7zqoaThZcbI0yjVOaVwyU0fQR9NFJTqmSEEX97p
LPZHU1CtAjRns7BW3ons9wPhy4s1xSPopJaHiXDwMMzAlx+kTcoFlFFvWCSlrcOC
MMo+eN1BQ3SbIxi3Ji3p6MnmSLIiE/wq4nKCEagKAv+AjtqRXYDIsT+28A96Xgeo
1R5agDamDMp0h6ZrhHMGSIgppWe+qvX14Jp3Hw0Nocgdyf8ABDR9H3/gZasXKbZu
LrbNLn3vNVKTMn9YpM0T94Uwf0nFPH6MOzFVmjahRute3TU7ioSXxbVPpNuiOkXj
RFXe1YUoILjLJgHZSUEpdHP+meGUjeScHTQt6jV97WfTeq2ZALg=
=Eoh1
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull 32-bit ARM SoC updates from Arnd Bergmann:
"These updates are for platform specific code in arch/arm/, mostly
fixing minor issues.
The at91 platform gains support for better power management on the
lan966 platform and new firmware on the sama5 platform. The mediatek
soc drivers in turn are enabled for the new mt8195 SoC"
* tag 'arm-soc-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (34 commits)
ARM: at91: debug: add lan966 support
ARM: at91: pm: add support for sama5d2 secure suspend
ARM: at91: add code to handle secure calls
ARM: at91: Kconfig: implement PIT64B selection
ARM: at91: pm: add quirks for pm
ARM: at91: pm: use kernel documentation style
ARM: at91: pm: introduce macros for pm mode replacement
ARM: at91: pm: keep documentation inline with structure members
orion5x: fix typos in comments
ARM: hisi: Add missing of_node_put after of_find_compatible_node
ARM: shmobile: rcar-gen2: Drop comma after OF match table sentinel
ARM: shmobile: Drop commas after dt_compat sentinels
soc: mediatek: mutex: remove mt8195 MOD0 and SOF0 definition
MAINTAINERS: Add Broadcom BCMBCA entry
arm: bcmbca: add arch bcmbca machine entry
MAINTAINERS: Broadcom internal lists aren't maintainers
dt-bindings: pwrap: mediatek: Update pwrap document for mt8195
soc: mediatek: add DDP_DOMPONENT_DITHER0 enum for mt8195 vdosys0
soc: mediatek: add mtk-mutex support for mt8195 vdosys0
soc: mediatek: add mtk-mmsys support for mt8195 vdosys0
...
of_find_matching_node() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: 5e68c0fc8d ("soc: amlogic: Add Meson6/Meson8/Meson8b/Meson8m2 SoC Information driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220524065729.33689-1-linmq006@gmail.com
Nexus 7 Android tablet can be turned off using a special bootloader
command which is conveyed to bootloader by putting magic value into the
special scratch register and then rebooting normally. This power-off
method should be invoked if USB cable is connected. Bootloader then will
display battery status and power off the device. This behaviour is
borrowed from downstream kernel and matches user expectations, otherwise
it looks like device got hung during power-off and it may wake up on
USB disconnect.
Switch PMC driver to sys-off handler API, which provides drivers with
chained power-off callbacks functionality that is required for powering-off
devices properly. It also brings resource-managed API for the restart
handler registration that makes PMC driver code cleaner.
Signed-off-by: Dmitry Osipenko <dmitry.osipenko@collabora.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As per the current implementation only single callback data gets saved per
event, driver is throwing an error if try to register multiple callback for
same event. So at time of unregistration of any event required things are
event details and callback handler as parameter of xlnx_unregister_event().
As part of adding support of multiple callbacks for same event also require
change in prototype of xlnx_unregister_event().
During unregistration of any events, now required things are event details,
callback handler and agent's private data as parameter of
xlnx_unregister_event().
Also modify the usage of xlnx_unregister_event() in xilinx/zynqmp_power.c
driver as per new implementation.
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Link: https://lore.kernel.org/r/20220427074803.19009-3-abhyuday.godhasara@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the current implementation of only single callback data gets
saved per event, driver is throwing an error if try to register multiple
callback for same event.
Add support of multiple callbacks data for same event. So agent can
register for same event with multiple callbacks. Here event management
driver will store the callbacks as list in Hash table entry for that event.
Here each callback data contain 2 element as callback handler and private
data of agent driver.
Signed-off-by: Abhyuday Godhasara <abhyuday.godhasara@xilinx.com>
Link: https://lore.kernel.org/r/20220427074803.19009-2-abhyuday.godhasara@xilinx.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Detailed description for this pull request:
1. Update devfreq core
- Add cpu based scaling support to passive governor. Some device like
cache might require the dynamic frequency scaling. But, it has very
tightly to cpu frequency. So that use passive governor to scale
the frequency according to current cpu frequency.
To decide the frequency of the device, the governor does one of the following:
: Derives the optimal devfreq device opp from required-opps property of
the parent cpu opp_table.
: Scales the device frequency in proportion to the CPU frequency. So, if
the CPUs are running at their max frequency, the device runs at its
max frequency. If the CPUs are running at their min frequency, the
device runs at its min frequency. It is interpolated for frequencies
in between.
2. Update devfreq driver
- Update rk3399_dmc.c as following:
: Convert dt-binding document to YAML and deprecate unused properties.
: Use Hz units for the device-tree properties of rk3399_dmc.
: rk3399_dmc is able to set the idle time before changing the dmc clock.
Specify idle time parameters by using nano-second unit on dt bidning.
: Add new disable-freq properties to optimize the power-saving feature
of rk3399_dmc.
: Disable devfreq-event device on remove() to fix unbalanced
enable-disable count.
: Use devm_pm_opp_of_add_table()
: Block PMU (Power-Management Unit) transitions when scaling frequency
by ARM Trust Firmware in order to fix the conflict between PMU and DMC
(Dynamic Memory Controller).
-----BEGIN PGP SIGNATURE-----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=/3W8
-----END PGP SIGNATURE-----
Merge tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux
Pull devfreq changes for 5.19-rc1 from Chanwoo Choi:
"1. Update devfreq core
- Add cpu based scaling support to passive governor. Some device like
cache might require the dynamic frequency scaling. But, it has very
tightly to cpu frequency. So that use passive governor to scale
the frequency according to current cpu frequency.
To decide the frequency of the device, the governor does one of the following:
: Derives the optimal devfreq device opp from required-opps property of
the parent cpu opp_table.
: Scales the device frequency in proportion to the CPU frequency. So, if
the CPUs are running at their max frequency, the device runs at its
max frequency. If the CPUs are running at their min frequency, the
device runs at its min frequency. It is interpolated for frequencies
in between.
2. Update devfreq drivers
- Update rk3399_dmc.c as following:
: Convert dt-binding document to YAML and deprecate unused properties.
: Use Hz units for the device-tree properties of rk3399_dmc.
: rk3399_dmc is able to set the idle time before changing the dmc clock.
Specify idle time parameters by using nano-second unit on dt bidning.
: Add new disable-freq properties to optimize the power-saving feature
of rk3399_dmc.
: Disable devfreq-event device on remove() to fix unbalanced
enable-disable count.
: Use devm_pm_opp_of_add_table()
: Block PMU (Power-Management Unit) transitions when scaling frequency
by ARM Trust Firmware in order to fix the conflict between PMU and DMC
(Dynamic Memory Controller)."
* tag 'devfreq-next-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux:
PM / devfreq: passive: Keep cpufreq_policy for possible cpus
PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
PM / devfreq: Add cpu based scaling support to passive governor
PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
PM / devfreq: rk3399_dmc: Block PMU during transitions
soc: rockchip: power-domain: Manage resource conflicts with firmware
PM / devfreq: rk3399_dmc: Avoid static (reused) profile
PM / devfreq: rk3399_dmc: Use devm_pm_opp_of_add_table()
PM / devfreq: rk3399_dmc: Disable edev on remove()
PM / devfreq: rk3399_dmc: Support new *-ns properties
PM / devfreq: rk3399_dmc: Support new disable-freq properties
PM / devfreq: rk3399_dmc: Use bitfield macro definitions for ODT_PD
PM / devfreq: rk3399_dmc: Drop excess timing properties
PM / devfreq: rk3399_dmc: Drop undocumented ondemand DT props
dt-bindings: devfreq: rk3399_dmc: Add more disable-freq properties
dt-bindings: devfreq: rk3399_dmc: Specify idle params in nanoseconds
dt-bindings: devfreq: rk3399_dmc: Fix Hz units
dt-bindings: devfreq: rk3399_dmc: Deprecate unused/redundant properties
dt-bindings: devfreq: rk3399_dmc: Convert to YAML
of_find_matching_node_and_match returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: 4c58063d42 ("soc: rockchip: add driver handling grf setup")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220516072013.19731-1-linmq006@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This converts a wide range of Qualcomm-related DeviceTree bindings to
YAML, in order to improve our ability to validate the DeviceTree source.
The RPMh power-domain driver gains support for the modem platform SDX65,
the compute platform SC8280XP and the automotive platform SA8540p. While
LLCC gains support for SC8180X and SC8280XP and gains a
MODULE_DEVICE_TABLE() to make it functional as a module.
It adds a driver for configuring the SSC bus, providing Linux access to
the hardware blocks in the sensor subsystem.
The socinfo driver gets confusion related to MSM8974 Pro sorted out and
adds new ids for SM8540 and SC7280.
The SCM driver gains support for MSM8974.
Add missing of_node_put() in smp2p and smsm drivers.
Stop using iterator after list_for_each_entry() and define static
definitions as such, in the PDR driver.
-----BEGIN PGP SIGNATURE-----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=/Dqp
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=rjVH
-----END PGP SIGNATURE-----
Merge tag 'qcom-drivers-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm driver updates for v5.19
This converts a wide range of Qualcomm-related DeviceTree bindings to
YAML, in order to improve our ability to validate the DeviceTree source.
The RPMh power-domain driver gains support for the modem platform SDX65,
the compute platform SC8280XP and the automotive platform SA8540p. While
LLCC gains support for SC8180X and SC8280XP and gains a
MODULE_DEVICE_TABLE() to make it functional as a module.
It adds a driver for configuring the SSC bus, providing Linux access to
the hardware blocks in the sensor subsystem.
The socinfo driver gets confusion related to MSM8974 Pro sorted out and
adds new ids for SM8540 and SC7280.
The SCM driver gains support for MSM8974.
Add missing of_node_put() in smp2p and smsm drivers.
Stop using iterator after list_for_each_entry() and define static
definitions as such, in the PDR driver.
* tag 'qcom-drivers-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (33 commits)
soc: qcom: pdr: use static for servreg_* variables
soc: qcom: llcc: Add sc8180x and sc8280xp configurations
dt-bindings: arm: msm: Add sc8180x and sc8280xp LLCC compatibles
soc: qcom: rpmhpd: add sc8280xp & sa8540p rpmh power-domains
soc: qcom: rpmhpd: Don't warn about sparse rpmhpd arrays
dt-bindings: power: rpmpd: Add sc8280xp RPMh power-domains
spi: dt-bindings: qcom,spi-geni-qcom: convert to dtschema
soc: qcom: socinfo: Sort out 8974PRO names
dt-bindings: soc: qcom,smp2p: convert to dtschema
dt-bindings: qcom: geni-se: Update UART schema reference
dt-bindings: qcom: geni-se: Update I2C schema reference
dt-bindings: soc: qcom,rpmh-rsc: convert to dtschema
bus: add driver for initializing the SSC bus on (some) qcom SoCs
dt-bindings: bus: add device tree bindings for qcom,ssc-block-bus
dt-bindings: qcom: qcom,geni-se: refer to dtschema for SPI
dt-bindings: soc: qcom,smd: convert to dtschema
firmware: qcom_scm: Add compatible for MSM8976 SoC
dt-bindings: firmware: qcom-scm: Document msm8976 bindings
soc: qcom: smem: validate fields of shared structures
soc: qcom: smem: map only partitions used by local HOST
...
Link: https://lore.kernel.org/r/20220509181839.316655-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- A series from Lucas and Paul to update GPCv2 driver for i.MX8MP power
domains, and add HSIO and HDMI block control support.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCgAyFiEEFmJXigPl4LoGSz08UFdYWoewfM4FAmJ3IvYUHHNoYXduZ3Vv
QGtlcm5lbC5vcmcACgkQUFdYWoewfM6lhwf7BpYDyiaYHBKQLXWWDZj1QanO6bjM
fMlxvVdggfeLW6ijerCb+wf2jNQY75lWRRny4x4WWP+sSVZ4u9SUJlxLrwo/aWYr
44KWWr4PkSMDm5j2bQyy8S9o01ZpxT/FOqqTC51PwgMx7yxB7+d1Z1txWwp5W0jB
Ps92O4bKRfvCCF7Mgjw3/FDu5iek6+9pHx5dQxQ1CWPuvVJos6M9Ktkv27x3oOvI
S4v6Y7v5m1WxSjUK2p09pIGP9AJrHhmRNJF3R/ZrXqUKAlpCQFK6DwZ9mY/rfcfj
tPoqCwj9/UmzG+GlBo8z7I2GQmF7vmwH6bqjP/T6SHOoxE9/fiqT2Swc5A==
=S4x7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmJ5g1gACgkQmmx57+YA
GNmd7A/7BR8AlCUX1H5SrWAiJbu0iR64vXRG+K6iqvEQV99K8zivQ7Sg6D+EwonR
YiLFOGTkk3O2hfZWbamNGDxmYrcjC5Kg3Zo0ZMJ2Cg91oBNB5olK/9hKOyrIfPMH
JTZJ/7n7nFi5xUFKBcof3VwNsqsHDp7XGl+jD7la8Dd9m4Yytofz3L4YxQLAkLhU
fobCmW/Nb9QxoKJL1aa+ix0HzZc00cvnUD3CqxFmqamJVJiPPnLFh+VgvDc1vP2P
q0bYvXuqL3lXVVbbi3jHqVldCwyzx7egcv72q33yGQPSaNEJ04jV/JUEz6sIj2XI
HfoQ5iyqczLPZMvJQiXxBsAy9wxde+qoMUwq7OvkLBBF+xEbwrkvp3wTElySRA6Y
YjP8nf39vuQ7qT9Lj4vNBJvQDoLbrKw+xEnFxjmCdJWgdqxVD0yVnPLjCFvmtFfl
/b3g8CePnUwupaI4K8nmo9dvMG46oe7xA86M6KphYdIUg0NVB+/kmxMnwSLBZ3Qz
HRIUyeqV6knzMo413GsQSe9zCiMRcsuDiQ8xHwe5Ko0P8Kr3kyPFX6ofv5D5I54W
leog0kQU/eYXMEveCqIaxjUFRb9SE8UY9SK//mAqzreLNFT896yG5GeD0WzRxwQl
oxtn+DdzpRHdjiDnS2OC4v22BvxVb3qLr0rVlCC1V3KFalxyRjU=
=2GwC
-----END PGP SIGNATURE-----
Merge tag 'imx-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/drivers
i.MX drivers update for 5.19:
- A series from Lucas and Paul to update GPCv2 driver for i.MX8MP power
domains, and add HSIO and HDMI block control support.
* tag 'imx-drivers-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
soc: imx: fix semicolon.cocci warnings
soc: imx: add i.MX8MP HDMI blk-ctrl
soc: imx: imx8m-blk-ctrl: Add i.MX8MP media blk-ctrl
soc: imx: add i.MX8MP HSIO blk-ctrl
dt-bindings: power: imx8mp: add defines for HDMI blk-ctrl domains
dt-bindings: soc: Add i.MX8MP media block control DT bindings
soc: imx: imx8m-blk-ctrl: set power device name
soc: imx: gpcv2: add support for i.MX8MP power domains
soc: imx: gpcv2: add PGC control register indirection
Link: https://lore.kernel.org/r/20220508033843.2773685-2-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* wkup_m3: io isolation, voltage scaling, vtt regulator and a debug option to stop m3 in suspend.
* tisci: support for polled mode for system suspend, reset driver is now enabled for COMPILE_TEST
* knav, dma.. misc cleanups for IS_ERR, pm_run_time*, and various other fixups.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE+KKGk1TrgjIXoxo03bWEnRc2JJ0FAmJ2m64ACgkQ3bWEnRc2
JJ0VrxAAkwYvb9VDyF2o0WqJZfllt7KqUXPMZ2ijayNwnDy1EVTmcHgjX7K4hA5Z
z9RX2kzeCobah2urRWVJvVnfsqUlAQB8xjtg9UMskjoicbmJ1OZ8/eOS+Ctwuco9
7VNVTDhqu7vIOdOtahJ6M9ajIWJorrWNrXf2s9eZZJLaJ3apGolOY6mqGKURq6QY
jnLvESmPIEtBrYjWr/dkrrPmGuffygM2i7J6RF9RJ3fKuNX7uS72nnYRHN714WU8
hRuJG4AaYRaEZmWfByXIktdakHBFiBP2g4Zvkeds8KXtRGoamYrrGXuPE1pb1w4p
kVhumbktMFMSNf37yWdjwo5M1hemhw6SNR3i/021Bt7DSmA7BC0+iLVDJwA+dsrr
XoCt8V6s3KydeNRDGYSQVECPExYqVyCp3bnHVWPjfS21zpLPmaOQvTA2TTRb737t
iRKnprDXAD/ALBq9XZbsC2L8jelcXkCOT/+vpCMR4jjyM8OZcmWFU3Nkgp/Uhst/
3zaL34i4EzvUlrkuHKu92GdNkzkfdd/bk/Emve+12v54QeyM/go8Tn3DLRsWVvg3
CRgMY5ldELIsPR3VHSTmE8M0YxpmpxM9ixiM0Yrs/V21EZLdiwejqznM9yaLgwM3
AwPo/WUImn+l+RINY3VdwoHV4dr6CMxkn2laFcQ/c9KEG39ZWH8=
=Nlpv
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=7h5b
-----END PGP SIGNATURE-----
Merge tag 'ti-driver-soc-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into arm/drivers
TI Driver updates for v5.19
* wkup_m3: io isolation, voltage scaling, vtt regulator and a debug option to stop m3 in suspend.
* tisci: support for polled mode for system suspend, reset driver is now enabled for COMPILE_TEST
* knav, dma.. misc cleanups for IS_ERR, pm_run_time*, and various other fixups.
* tag 'ti-driver-soc-for-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
soc: ti: wkup_m3_ipc: Add debug option to halt m3 in suspend
soc: ti: wkup_m3_ipc: Add support for i2c voltage scaling
soc: ti: wkup_m3_ipc: Add support for IO Isolation
soc: ti: knav_qmss_queue: Use IS_ERR instead of IS_ERR_OR_NULL when checking knav_queue_open() result
soc: ti: pm33xx: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
firmware: ti_sci: Switch transport to polled mode during system suspend
soc: ti: wkup_m3_ipc: Add support for toggling VTT regulator
soc: ti: knav_qmss_queue: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
soc: ti: knav_dma: Use pm_runtime_resume_and_get instead of pm_runtime_get_sync
reset: ti-sci: Allow building under COMPILE_TEST
soc: ti: ti_sci_pm_domains: Check for null return of devm_kcalloc
soc: ti: omap_prm: Use of_device_get_match_data()
soc: ti: pruss: using pm_runtime_resume_and_get instead of pm_runtime_get_sync
soc: ti: replace usage of found with dedicated list iterator variable
soc: ti: wkup_m3_ipc: fix platform_get_irq.cocci warning
Link: https://lore.kernel.org/r/20220507163424.pvqnwrxpoo73lmp2@debtless
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
On RK3399 platforms, power domains are managed mostly by the kernel
(drivers/soc/rockchip/pm_domains.c), but there are a few exceptions
where ARM Trusted Firmware has to be involved:
(1) system suspend/resume
(2) DRAM DVFS (a.k.a., "ddrfreq")
Exception (1) does not cause much conflict, since the kernel has
quiesced itself by the time we make the relevant PSCI call.
Exception (2) can cause conflict, because of two actions:
(a) ARM Trusted Firmware needs to read/modify/write the PMU_BUS_IDLE_REQ
register to idle the memory controller domain; the kernel driver
also has to touch this register for other domains.
(b) ARM Trusted Firmware needs to manage the clocks associated with
these domains.
To elaborate on (b): idling a power domain has always required ungating
an array of clocks; see this old explanation from Rockchip:
https://lore.kernel.org/linux-arm-kernel/54503C19.9060607@rock-chips.com/
Historically, ARM Trusted Firmware has avoided this issue by using a
special PMU_CRU_GATEDIS_CON0 register -- this register ungates all the
necessary clocks -- when idling the memory controller. Unfortunately,
we've found that this register is not 100% sufficient; it does not turn
the relevant PLLs on [0].
So it's possible to trigger issues with something like the following:
1. enable a power domain (e.g., RK3399_PD_VDU) -- kernel will
temporarily enable relevant clocks/PLLs, then turn them back off
2. a PLL (e.g., PLL_NPLL) is part of the clock tree for
RK3399_PD_VDU's clocks but otherwise unused; NPLL is disabled
3. perform a ddrfreq transition (rk3399_dmcfreq_target() -> ...
drivers/clk/rockchip/clk-ddr.c / ROCKCHIP_SIP_DRAM_FREQ)
4. ARM Trusted Firmware unagates VDU clocks (via PMU_CRU_GATEDIS_CON0)
5. ARM Trusted firmware idles the memory controller domain
6. Step 5 waits on the VDU domain/clocks, but NPLL is still off
i.e., we hang the system.
So for (b), we need to at a minimum manage the relevant PLLs on behalf
of firmware. It's easier to simply manage the whole clock tree, in a
similar way we do in rockchip_pd_power().
For (a), we need to provide mutual exclusion betwen rockchip_pd_power()
and firmware. To resolve that, we simply grab the PMU mutex and release
it when ddrfreq is done.
The Chromium OS kernel has been carrying versions of part of this hack
for a while, based on some new custom notifiers [1]. I've rewritten as a
simple function call between the drivers, which is OK because:
* the PMU driver isn't enabled, and we don't have this problem at all
(the firmware should have left us in an OK state, and there are no
runtime conflicts); or
* the PMU driver is present, and is a single instance.
And the power-domain driver cannot be removed, so there's no lifetime
management to worry about.
For completeness, there's a 'dmc_pmu_mutex' to guard (likely
theoretical?) probe()-time races. It's OK for the memory controller
driver to start running before the PMU, because the PMU will avoid any
critical actions during the block() sequence.
[0] The RK3399 TRM for PMU_CRU_GATEDIS_CON0 only talks about ungating
clocks. Based on experimentation, we've found that it does not power
up the necessary PLLs.
[1] CHROMIUM: soc: rockchip: power-domain: Add notifier to dmc driver
https://chromium-review.googlesource.com/q/I242dbd706d352f74ff706f5cbf42ebb92f9bcc60
Notably, the Chromium solution only handled conflict (a), not (b).
In practice, item (b) wasn't a problem in many cases because we
never managed to fully power off PLLs. Now that the (upstream) video
decoder driver performs runtime clock management, we often power off
NPLL.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There are two drivers in arch/arm/plat-pxa: mfp and ssp. Both
of them should ideally not be needed at all, as there are
proper subsystems to replace them.
OTOH, they are self-contained and can simply be normal
SoC drivers, so move them over there to eliminate one more
of the plat-* directories.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr> (mach-pxa)
Acked-by: Lubomir Rintel <lkundrak@v3.sk> (mach-mmp)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This set of changes adds nvmem cell lookup entries for Tegra194 that are
used to read calibration data from the SoC fuses, and updates the reset
sources for Tegra234.
Other than that, included is a minor build fix for a missing dependency
that can be encountered very rarely in random config builds. Lastly some
kerneldoc comments are added to avoid build warnings.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmJ1LD8THHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zoYh8D/9PZ9Z6MfFP/4mU+LQccO7OW4iw+nUq
J3LSOby2SRlTBLz0BsgYYoxEd1jDcPTvN9ND9tkmy8I77doVfgq2tcnBxqKZSwdy
w+mhr68cjx5yy0KieevSb3JSEp6hXL728j1CnxofHFy51NY2yuqcIwNRMEfYYX1d
UkCGaFnEjU1PvawDSKiruNy2r8oZaPDKXwtkhGxJedQ83CkCtkE2qNHi1GcJogo9
O8RB7eGIiZflloY83SlhoLm/qILBTGuARKUeXIEC66Ss6tbl1DccJ1i8iZlMr4uV
mOd+jnCiAkzL+EY9geD8e8cltAPqD5lhIwQB4kseB3Jw0+BRgmSMo/qlKo6zoC2x
nxaq5haxKAcE+fY1o5/h36hXCD5ZoeSTRlXowyXuLzvLkzhE/tMdC7SqqjTuDMe4
Yjf4yp50vEnbjdbnSx57yPqT7q1vclcV/or9MkravkV5zSxhzSUgfnuCAabrKNrQ
a/aiGy1yJD2V3iC1jhTQNaja/e7iUNF+TNmEGLlkZSpLzp9nDHJra5h+BklulGVb
qApf2o7sc6I5n7iyb+6WypBbHP+sX6PkkNWx4KDvUmsp3jG7LQiJQPdRiq60iicV
KQ1FqzDjhTyfxxiR2PwDGNZQsyK6DO3qST1oqk3pav55G6aHLsQx4+g3+tFIMhnN
oXskT6rAWqmjyw==
=Gmv7
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=S4fJ
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-5.19-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/drivers
soc/tegra: Changes for v5.19-rc1
This set of changes adds nvmem cell lookup entries for Tegra194 that are
used to read calibration data from the SoC fuses, and updates the reset
sources for Tegra234.
Other than that, included is a minor build fix for a missing dependency
that can be encountered very rarely in random config builds. Lastly some
kerneldoc comments are added to avoid build warnings.
* tag 'tegra-for-5.19-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Document core domain fields
soc/tegra: pmc: Select REGMAP
soc/tegra: pmc: Update Tegra234 reset sources
soc/tegra: fuse: Add nvmem cell lookup entries for Tegra194
Link: https://lore.kernel.org/r/20220506143005.3916655-2-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
These fields are used to track the state of the core domain. Add basic
descriptions so that kerneldoc can be properly generated for them.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sparse reports this repesentative issue
pdr_internal.h:31:22: warning: symbol 'servreg_location_entry_ei' was not declared. Should it be static?
Similar for other servreg_*
Global variables should not be defined in header files.
This only works because pdr_internal.h is only included
by pdr_interface.c. Single file use variables should be
static so add static to their storage-class specifiers.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20220422173806.21982-1-trix@redhat.com
- RTKit IPC library required to boot and communicate with
co-processors embedded inside Apple SoCs
- SART DMA address filter required to allow some DMA transactions for
the NVMe co-processor
- NVMe platform driver
The following minor changes since v3 on the mailing list have been
folded in:
- sart: %llx -> %pa for a phys_addr_t
- rtkit:/sart: Drop IS_ENABLED inside headers
- rtkit: Use EXPORT_SYMBOL_GPL instead of EXPORT_SYMBOL
- nvme: Set NVME_REQ_CANCELLED in the timeout handler
- nvme: Use DEFINE_SIMPLE_DEV_PM_OPS instead of #ifdef CONFIG_PM_SLEEP
-----BEGIN PGP SIGNATURE-----
iIkEABYKADEWIQRUAfN3OZ14tapALxsd6alOrecRcQUCYm/5lhMcc3ZlbkBzdmVu
cGV0ZXIuZGV2AAoJEB3pqU6t5xFxITsBAI02bdBvHQAFouu1WzhLzlAPNqjGv3Th
YFOJL4y2oyigAP9zkIGP0e1JcpApPxvlmQnM340ZY+TCth+ahoCWlS4VAg==
=b0QX
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEo6/YBQwIrVS28WGKmmx57+YAGNkFAmJ0IIIACgkQmmx57+YA
GNnxlg/+M0d7awpSyiN2g2aoPN9PzaDiWgjSDJ30THfY+JodFmK/Uw1L2dO32+md
0UMuMH9Vtiy3NXf/dDoLU+kiNQgT1ZY7Iw2220GZyHxRUC/7RZ/zGNvAb1FclDhK
YEYtlA2fK1MvlhEcriD8ytP78R80UA7Cx4o5T8CkgfN2OtjLip72aMCFtzRfxMk6
W0GQvkTpDtp3qn59Wlz/JEJKMT+q0txxq1QkPW93Su190S/7Lk/nd+CkmFDHx54n
2LFa33JuZZfNbzPMN9emTl7G5Z7Y241zYBMHvtAzd3WdaDZ6I1apeVnDXrNRhysC
4B8si4qbo9NORhWR96okll0MCiBNZ1UfvS4U+/8A1b0CHwX5rEUKLNOXIfO8xApi
L3HvVUpYPJw8w3aK2SKGVt2aQcnbluy9+LJQgHByPFbeIV80OjWoR4xSSZi2XErl
tp4vmyUBTR8g85EnCqcc8OWCdl+yMjX+NmftLk/XB7/xD+HtqKocqizOVho/9u+K
rv6Ivx6JHk33LFG/jJkN6q8OncgfSRirg0oy6IF/dy2xS2U3OtfaIXHIy9NosC36
B3bm8mb3CVQJxazMYl3rstBGQoN1YpuwOsHRUWiWG1jDnXFwCSck9b5OH+y64PME
45V27Rx1ftTgrOWgsllIqsviWADO4Qj7n5YXYvC+hGrBeDnM8pQ=
=gi38
-----END PGP SIGNATURE-----
Merge tag 'asahi-soc-rtkit-sart-nvme-for-5.19' of https://github.com/AsahiLinux/linux into arm/drivers
Apple SoC NVMe driver and dependencies:
- RTKit IPC library required to boot and communicate with
co-processors embedded inside Apple SoCs
- SART DMA address filter required to allow some DMA transactions for
the NVMe co-processor
- NVMe platform driver
The following minor changes since v3 on the mailing list have been
folded in:
- sart: %llx -> %pa for a phys_addr_t
- rtkit:/sart: Drop IS_ENABLED inside headers
- rtkit: Use EXPORT_SYMBOL_GPL instead of EXPORT_SYMBOL
- nvme: Set NVME_REQ_CANCELLED in the timeout handler
- nvme: Use DEFINE_SIMPLE_DEV_PM_OPS instead of #ifdef CONFIG_PM_SLEEP
* tag 'asahi-soc-rtkit-sart-nvme-for-5.19' of https://github.com/AsahiLinux/linux:
nvme-apple: Add initial Apple SoC NVMe driver
dt-bindings: nvme: Add Apple ANS NVMe
soc: apple: Add SART driver
dt-bindings: iommu: Add Apple SART DMA address filter
soc: apple: Add RTKit IPC library
soc: apple: Always include Makefile
Link: https://lore.kernel.org/r/20220505154020.84638-1-sven@svenpeter.dev
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
5.19, please pull the following:
- Qintao adds a missing NULL check to the Broadcom PMB driver after a
memory allocation
- Li removes the redundant suppress_bind_attrs from the brcmstb_gisb
driver which only has a probe and no remove function
-----BEGIN PGP SIGNATURE-----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=DrJC
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----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=ycAK
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-5.19/drivers' of https://github.com/Broadcom/stblinux into arm/drivers
This pull request contains Broadcom ARM/ARM64 SoCs drivers changes for
5.19, please pull the following:
- Qintao adds a missing NULL check to the Broadcom PMB driver after a
memory allocation
- Li removes the redundant suppress_bind_attrs from the brcmstb_gisb
driver which only has a probe and no remove function
* tag 'arm-soc/for-5.19/drivers' of https://github.com/Broadcom/stblinux:
bus: brcmstb_gisb: Remove the suppress_bind_attrs attribute of the driver
soc: bcm: Check for NULL return of devm_kzalloc()
Link: https://lore.kernel.org/r/20220504210942.1838248-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This adds driver support for the HDMI blk-ctrl found on the
i.MX8MP SoC.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the description for the i.MX8MP media blk-ctrl.
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de> # MX8MP LCDIF #1 and #2
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8MP added some blk-ctrl peripherals that don't follow the regular
structure of the blk-ctrls in the previous SoCs. Add a new file for those
with currently only the HSIO blk-ctrl being supported. Others will be added
later on.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Set the name for the virtual power device to the name of the attached
blk-ctrl domain. Makes the debug output for the power domains a lot
more pleasant to read.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 9d5e7c3e36 ("soc/tegra: pmc: Provide USB sleepwalk register
map") introduced a dependency on the regmap infrastructure, so select
the corresponding Kconfig entry. This avoids failures in random builds
that may otherwise end up having SOC_TEGRA_PMC enabled but not REGMAP.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add a debugfs option to allow configurable halting of the wkup_m3
during suspend at the last possible point before low power mode entry.
This condition can only be resolved through JTAG and advancing beyond
the while loop in a8_lp_ds0_handler [1]. Although this hangs the system
it forces the system to remain active once it has been entirely
configured for low power mode entry, allowing for register inspection
through JTAG to help in debugging transition errors.
Halt mode can be set using the enable_off_mode entry under wkup_m3_ipc
in the debugfs.
[1] https://git.ti.com/cgit/processor-firmware/ti-amx3-cm3-pm-firmware/tree/src/pm_services/pm_handlers.c?h=08.02.00.006#n141
Suggested-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[dfustini: add link for a8_lp_ds0_handler() in ti-amx3-cm3-pm-firmware]
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220502033211.1383158-1-dfustini@baylibre.com
Allow loading of a binary containing i2c scaling sequences to be
provided to the wkup_m3 firmware in order to properly scale voltage
rails on the PMIC during low power modes like DeepSleep0. Proper binary
format is determined by the FW in use.
Code expects firmware to have 0x0C57 present as the first two bytes
followed by one byte defining offset to sleep sequence followed by one
byte defining offset to wake sequence and then lastly both sequences.
Each sequence is a series of I2C transfers in the form:
u8 length | u8 chip address | u8 byte0/reg address | u8 byte1 | u8 byteN
..
The length indicates the number of bytes to transfer, including the
register address. The length of each transfer is limited by the I2C
buffer size of 32 bytes.
Based on previous work by Russ Dill.
[dfustini: replace FW_ACTION_HOTPLUG with FW_ACTION_UEVENT]
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
[dfustini: add NULL argument to rproc_da_to_va() call]
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220426200741.712842-3-dfustini@baylibre.com
AM43xx support isolation of the IOs so that control is taken
from the peripheral they are connected to and overridden by values
present in the CTRL_CONF_* registers for the pad in the control module.
The actual toggling happens from the wkup_m3, so use a DT property from
the wkup_m3_ipc node to allow the PM code to communicate the necessity
for placing the IOs into isolation to the firmware.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Drew Fustini <dfustini@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20220414192722.2978837-3-dfustini@baylibre.com
As the usage of knav_queue_open():
* Returns a handle to the open hardware queue if successful. Use IS_ERR()
* to check the returned value for error codes.
It will only return error codes, not null.
Signed-off-by: Haowen Bai <baihaowen@meizu.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/1650765944-20170-1-git-send-email-baihaowen@meizu.com
Using pm_runtime_resume_and_get is more appropriate
for simplifing code
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tony Lindgren <tony@aotmide.com>
Link: https://lore.kernel.org/r/20220418063059.2558074-1-chi.minghao@zte.com.cn
The NVMe co-processor on the Apple M1 uses a DMA address filter called
SART for some DMA transactions. This adds a simple driver used to
configure the memory regions from which DMA transactions are allowed.
Unlike a real IOMMU, SART does not support any pagetables and can't be
implemented inside the IOMMU subsystem using iommu_ops.
It also can't be implemented using dma_map_ops since not all DMA
transactions of the NVMe controller are filtered by SART.
Instead, most buffers have to be registered using the integrated NVMe
IOMMU and we can't have two separate dma_map_ops implementations for a
single device.
Co-developed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Apple SoCs such as the M1 come with multiple embedded co-processors
running proprietary firmware. Communication with those is established
over a simple mailbox using the RTKit IPC protocol.
This cannot be implemented inside the mailbox subsystem since on top
of communication over channels we also need support for starting,
hibernating and resetting these co-processors. We also need to
handle shared memory allocations differently depending on the
co-processor and don't want to split that across multiple drivers.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
We want to allow the code inside drivers/soc/apple to be compiled with
COMPILE_TEST but this will currently result in linking errors because
ARCH_APPLE is not set and make will never recurse into
drivers/soc/apple.
Let's just unconditionally recurse into apple/ since all drivers
in there are guarded by config options anyways.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Krzysztof Kozlowski