smatch reports wait_status is uninitialized, because smatch cannot assume
the loop body is ever executed.
Clarify the code so that wait_status is retrieved at least once.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Add get_rf_strength callback to get RSSI from the tuner. DVBv5
stat cache is updated. get_rf_strength is called by tuner_core
for analog tuners and is also used by some bridge drivers to
obtain RSSI directly from the tuner.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
In some debugging cases it is useful to know how long it took
signal lock to happen after tuning. This can help diagnose
line issues.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
To detect errors in the tuning operation, this waits up 40ms for operation
completion status. This allows for error detection and prevents issuing
additional commands to the tuner before it is finished.
Tuning typically completes in 20-30ms.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Include set_analog_params, get_frequency, and get_bandwidth.
Tested with NTSC and PAL standards via ch3/4 generator. Other standards
are included, but are untested due to lack of generator.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Getting the Xtal trim property to check if running is less error prone.
Reset if_frequency if state is unknown.
Replaces the previous "garbage check".
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Check error status bit on command execute, if error bit is
set return -EAGAIN. Ignore -EAGAIN in probe during device check.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Enable flags to get status of commands sent to the tuner.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
While at it, convert to kernel-doc format and use bits instead of bools.
Signed-off-by: Gon Solo <gonsolo@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Works in ATSC and QAM as is, DVB is completely untested.
Firmware required.
Signed-off-by: Brad Love <brad@nextdimension.cc>
Reviewed-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As we don't need anymore to share pad numbers with similar
drivers, use its own pad definition instead of a global
model.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Consumer devices are provided with a wide different range of types
supported by the same driver, allowing different configutations.
In order to make easier to setup media controller links, "taint"
pads with the signal type it carries.
While here, get rid of DEMOD_PAD_VBI_OUT, as the signal it carries
is actually the same as the normal video output.
The difference happens at the video/VBI interface:
- for VBI, only the hidden lines are streamed;
- for video, the stream is usually cropped to hide the
vbi lines.
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Right now, satellite tuner drivers specify frequencies in kHz,
while terrestrial/cable ones specify in Hz. That's confusing
for developers.
However, the main problem is that universal tuners capable
of handling both satellite and non-satelite delivery systems
are appearing. We end by needing to hack the drivers in
order to support such hybrid tuners.
So, convert everything to specify tuner frequencies in Hz.
Plese notice that a similar patch is also needed for frontends.
Tested-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Acked-by: Michael Büsch <m@bues.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
On several places, whitespaces are being used for indentation,
or even at the end of the line.
Fix them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The Si2141 needs two distinct commands for powerup/reset, otherwise it
will not respond to chip revision requests. It also needs a firmware
to run properly.
Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
'Reset' loop does not look correct. I tested it very many times and
it never repeated those commands. If problem, it tries to solve,
really occurs on some situations better solution should be find out.
There is another patch which does not have such hackish looking loop.
Lets change to it.
Cc: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Disable runtime unbind as driver does not support it.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Detect if firmware is running run-time and download / start it only
when needed. Detection is done by reading IF frequency value.
Garbage value is returned by firmware when it is not running,
otherwise correct value is returned.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
si2157_remove was calling kfree(dev) with possibly still active
schedule_delayed_work(dev->stat_work). This caused kernel panics in
call_timer_fn e.g. after rmmod cx23885.
Signed-off-by: Ernst Martin Witte <emw-linux-kernel@nocabal.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
A previous patch added a check if the firmware is too big, but it didn't
set the return error code with the right value.
[mchehab@osg.samsung.com: I ended by applying a v1 of Laura's patch, without
the proper return code. This patch contains the difference between v2 and v1 of
the Laura's "si2157: Bounds check firmware" patch]
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Reviewed-by: Olli Salonen <olli.salonen@iki.fi>
Tested-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The chips supported by the si2157 driver have two IF outputs (either
pins 12+13 or pins 9+11). Instead of hardcoding the output to be used
add an option to choose which output shall be used.
As this patch changes the default behaviour, the IF interface is
specified in each driver currently using si2157 driver. This is to
keep bisectability.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Si2157 tuner supports ATSC in addition to DVB-T and DVB-C. Extend
minimum frequency range to cover the complete ATSC/QAM-B range.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
For supporting ATSC and QAM modes the driver should use a smaller IF frequency than 5 MHz.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmware variable from fw_file to fw_name and change its
type from u8 to const char as request_firmware() input is.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Print chip version once using log level into when init() is called.
Remove cold/warm state printing as those are not very useful.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Firmware version could be printed similarly than si2168 driver does.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use own goto label for error case mem free is needed, even kfree could
be called with NULL. I think it is better to have it, even not required.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
- Rename ID table.
- Remove magic numbers from ID table driver data field.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Rename firmare download error path goto label. Remove firmware NULL
set as NULL value is not needed anymore, due to recent change which
started using goto labels for firmware error handling.
Cc: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Carry struct i2c_client pointer in tuner_priv. This driver is I2C driver,
which is represented as a struct i2c_client, so better to carry this top
level structure for each routine in order to unify things.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Remove if () from firmware command error path as there should not be
any error prone conditional logic there. Use goto labels instead.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
'dev' is likely most common name in kernel for structure containing
device state instance, so rename it in order to keep things
consistent.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The release_firmware() function was called in some cases by the si2157_init()
function during error handling even if the passed variable contained still
a null pointer. This implementation detail could be improved
by the introduction of another jump label.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The release_firmware() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Break after goto is unnecessary.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The Silicon Labs Si2146 tuner seems to work with the same driver as the Si2157,
but there a few exceptions. The powerup command seems to be quite a bit
different. In addition there's a property 0207 that requires a different value.
Thus another entry is created in the si2157_id table to support also si2146 in
this driver.
The datasheet is available on manufacturer's website:
http://www.silabs.com/support%20documents/technicaldocs/Si2146-short.pdf
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set the property for delivery system also in case of SYS_DVBC_ANNEX_B.
This behaviour is observed in the sniffs taken with Hauppauge HVR-955Q
Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds support for Si2147-A30 tuner. Fairly trivial, no firmware needed for this tuner. However, command 14 00 02 07 01 00 seems to be mandatory. On Si2157 and Si2158 the value 0x0100 is the default value, so this patch does not impact the existing tuners/devices. On Si2147 the default is 0x0000 and I can't get a lock with that value.
While here, fix the return length of the previous set command to 4 bytes.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add a variable into state to keep track if firmware has been loaded or not.
Skip firmware loading in case it is already loaded (resume from sleep).
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Instead of sending command 13 to the tuner, send command 16 when sleeping. This
behaviour is observed when using manufacturer provided binary-only Linux driver
for TechnoTrend CT2-4400 (Windows driver does not do power management).
The issue with command 13 is that firmware loading is necessary after that.
This is not an issue with tuners that do not require firmware, but starting
streaming after sleep on an Si2158 takes noticeable time as firmware is
loaded on resume.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Set the property for delivery system also in case of SYS_ATSC. This
behaviour is observed in the sniffs taken with Hauppauge HVR-955Q
Windows driver.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Same thing for si2157 as Antti did earlier for tda18212:
There is no need to print module name nor function name as those
are done by kernel logging system when dev_xxx logging is used and
driver is proper I2C driver.
While here, fix a typo ("unknown") in si2157_init.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Sean Young