Last night we had scsi problems and a hardware raid unit was offlined
during heavy i/o. While this happened we got for about 3 minutes a huge
number messages like these
Apr 12 03:36:07 pfs1n14 kernel: [197510.696595] raid5:md7: read error not correctable (sector 2993096568 on sdj2).
I guess the high error rate is responsible for not scheduling other events
- during this time the system was not pingable and in the end also other
devices run into scsi command timeouts causing problems on these unrelated
devices as well.
Signed-off-by: Bernd Schubert <bernd-schubert@gmx.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As setting and clearing queue flags now requires that we hold a spinlock
on the queue, and as blk_queue_stack_limits is called without that lock,
get the lock inside blk_queue_stack_limits.
For blk_queue_stack_limits to be able to find the right lock, each md
personality needs to set q->queue_lock to point to the appropriate lock.
Those personalities which didn't previously use a spin_lock, us
q->__queue_lock. So always initialise that lock when allocated.
With this in place, setting/clearing of the QUEUE_FLAG_PLUGGED bit will no
longer cause warnings as it will be clear that the proper lock is held.
Thanks to Dan Williams for review and fixing the silly bugs.
Signed-off-by: NeilBrown <neilb@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Alistair John Strachan <alistair@devzero.co.uk>
Cc: Nick Piggin <npiggin@suse.de>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jacek Luczak <difrost.kernel@gmail.com>
Cc: Prakash Punnoor <prakash@punnoor.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit bd2ab67030 "md: close a livelock window
in handle_parity_checks5" introduced a bug in handling 'repair' operations.
After a repair operation completes we clear the state bits tracking this
operation. However, they are cleared too early and this results in the code
deciding to re-run the parity check operation. Since we have done the repair
in memory the second check does not find a mismatch and thus does not do a
writeback.
Test results:
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
51072
$ echo repair > /sys/block/md0/md/sync_action
$ cat /sys/block/md0/md/mismatch_cnt
0
(also fix incorrect indentation)
Cc: <stable@kernel.org>
Tested-by: George Spelvin <linux@horizon.com>
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Allows a userspace metadata handler to take action upon detecting a device
failure.
Based on an original patch by Neil Brown.
Changes:
-added blocked_wait waitqueue to rdev
-don't qualify Blocked with Faulty always let userspace block writes
-added md_wait_for_blocked_rdev to wait for the block device to be clear, if
userspace misses the notification another one is sent every 5 seconds
-set MD_RECOVERY_NEEDED after clearing "blocked"
-kill DoBlock flag, just test mddev->external
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MD drivers use one printk() call to print 2 log messages and the second line
may be prefixed by a TAB character. It may also output a trailing space
before newline. klogd (I think) turns the TAB character into the 2 characters
'^I' when logging to a file. This looks ugly.
Instead of a leading TAB to indicate continuation, prefix both output lines
with 'raid:' or similar. Also remove any trailing space in the vicinity of
the affected code and consistently end the sentences with a period.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
strict_strtoul handles the open-coded sanity checks in
raid5_store_stripe_cache_size and raid5_store_preread_threshold
Acked-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve write performance by preventing the delayed_list from dumping all its
stripes onto the handle_list in one shot. Delayed stripes are now further
delayed by being held on the 'hold_list'. The 'hold_list' is bypassed when:
* a STRIPE_IO_STARTED stripe is found at the head of 'handle_list'
* 'handle_list' is empty and i/o is being done to satisfy full stripe-width
write requests
* 'bypass_count' is less than 'bypass_threshold'. By default the threshold
is 1, i.e. every other stripe handled is a preread stripe provided the
top two conditions are false.
Benchmark data:
System: 2x Xeon 5150, 4x SATA, mem=1GB
Baseline: 2.6.24-rc7
Configuration: mdadm --create /dev/md0 /dev/sd[b-e] -n 4 -l 5 --assume-clean
Test1: dd if=/dev/zero of=/dev/md0 bs=1024k count=2048
* patched: +33% (stripe_cache_size = 256), +25% (stripe_cache_size = 512)
Test2: tiobench --size 2048 --numruns 5 --block 4096 --block 131072 (XFS)
* patched: +13%
* patched + preread_bypass_threshold = 0: +37%
Changes since v1:
* reduce bypass_threshold from (chunk_size / sectors_per_chunk) to (1) and
make it configurable. This defaults to fairness and modest performance
gains out of the box.
Changes since v2:
* [neilb@suse.de]: kill STRIPE_PRIO_HI and preread_needed as they are not
necessary, the important change was clearing STRIPE_DELAYED in
add_stripe_bio and this has been moved out to make_request for the hang
fix.
* [neilb@suse.de]: simplify get_priority_stripe
* [dan.j.williams@intel.com]: reset the bypass_count when ->hold_list is
sampled empty (+11%)
* [dan.j.williams@intel.com]: decrement the bypass_count at the detection
of stripes being naturally promoted off of hold_list +2%. Note, resetting
bypass_count instead of decrementing on these events yields +4% but that is
probably too aggressive.
Changes since v3:
* cosmetic fixups
Tested-by: James W. Laferriere <babydr@baby-dragons.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a failure is detected after a parity check operation has been initiated,
but before it completes handle_parity_checks5 will never quiesce operations on
the stripe.
Explicitly handle this case by "canceling" the parity check, i.e. clear the
STRIPE_OP_CHECK flags and queue the stripe on the handle list again to refresh
any non-uptodate blocks.
Kernel versions >= 2.6.23 are susceptible.
Cc: <stable@kernel.org>
Cc: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc-3.4.5 on sparc64:
drivers/md/raid5.c: In function `raid5_end_read_request':
drivers/md/raid5.c:1147: warning: long long unsigned int format, long unsigned int arg (arg 4)
drivers/md/raid5.c:1164: warning: long long unsigned int format, long unsigned int arg (arg 3)
drivers/md/raid5.c:1170: warning: long long unsigned int format, long unsigned int arg (arg 3)
sector_t is u64, and we don't know what type the architecture uses to
implement u64 (on some it is unsigned long).
Cc: Neil Brown <neilb@suse.de>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
raid5's 'make_request' function calls generic_make_request on underlying
devices and if we run out of stripe heads, it could end up waiting for one of
those requests to complete. This is bad as recursive calls to
generic_make_request go on a queue and are not even attempted until
make_request completes.
So: don't make any generic_make_request calls in raid5 make_request until all
waiting has been done. We do this by simply setting STRIPE_HANDLE instead of
calling handle_stripe().
If we need more stripe_heads, raid5d will get called to process the pending
stripe_heads which will call generic_make_request from a
This change by itself causes a performance hit. So add a change so that
raid5_activate_delayed is only called at unplug time, never in raid5. This
seems to bring back the performance numbers. Calling it in raid5d was
sometimes too soon...
Neil said:
How about we queue it for 2.6.25-rc1 and then about when -rc2 comes out,
we queue it for 2.6.24.y?
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Tested-by: dean gaudet <dean@arctic.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As this is more in line with common practice in the kernel. Also swap the
args around to be more like list_for_each.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This allows userspace to control resync/reshape progress and synchronise it
with other activities, such as shared access in a SAN, or backing up critical
sections during a tricky reshape.
Writing a number of sectors (which must be a multiple of the chunk size if
such is meaningful) causes a resync to pause when it gets to that point.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently an md array with a write-intent bitmap does not updated that bitmap
to reflect successful partial resync. Rather the entire bitmap is updated
when the resync completes.
This is because there is no guarentee that resync requests will complete in
order, and tracking each request individually is unnecessarily burdensome.
However there is value in regularly updating the bitmap, so add code to
periodically pause while all pending sync requests complete, then update the
bitmap. Doing this only every few seconds (the same as the bitmap update
time) does not notciably affect resync performance.
[snitzer@gmail.com: export bitmap_cond_end_sync]
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Mike Snitzer" <snitzer@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We currently do not wait for the block from the missing device to be
computed from parity before copying data to the new stripe layout.
The change in the raid6 code is not techincally needed as we don't delay
data block recovery in the same way for raid6 yet. But making the change
now is safer long-term.
This bug exists in 2.6.23 and 2.6.24-rc
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
<debug output from Joel's system>
handling stripe 7629696, state=0x14 cnt=1, pd_idx=2 ops=0:0:0
check 5: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ffcffcc0 written 0000000000000000
check 4: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fdd4e360 written 0000000000000000
check 3: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 2: state 0x1 toread 0000000000000000 read 0000000000000000 write 0000000000000000 written 0000000000000000
check 1: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800ff517e40 written 0000000000000000
check 0: state 0x6 toread 0000000000000000 read 0000000000000000 write fffff800fd4cae60 written 0000000000000000
locked=4 uptodate=2 to_read=0 to_write=4 failed=0 failed_num=0
for sector 7629696, rmw=0 rcw=0
</debug>
These blocks were prepared to be written out, but were never handled in
ops_run_biodrain(), so they remain locked forever. The operations flags
are all clear which means handle_stripe() thinks nothing else needs to be
done.
This state suggests that the STRIPE_OP_PREXOR bit was sampled 'set' when it
should not have been. This patch cleans up cases where the code looks at
sh->ops.pending when it should be looking at the consistent stack-based
snapshot of the operations flags.
Report from Joel:
Resync done. Patch fix this bug.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Cc: <stable@kernel.org>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
commit 4ae3f847e4 ("md: raid5: fix
clearing of biofill operations") did not get applied correctly,
presumably due to substantial similarities between handle_stripe5 and
handle_stripe6.
This patch moves the chunk of new code from handle_stripe6 (where it isn't
needed (yet)) to handle_stripe5.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Dan Williams" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ops_complete_biofill() runs outside of spin_lock(&sh->lock) and clears the
'pending' and 'ack' bits. Since the test_and_ack_op() macro only checks
against 'complete' it can get an inconsistent snapshot of pending work.
Move the clearing of these bits to handle_stripe5(), under the lock.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Tested-by: Joel Bertrand <joel.bertrand@systella.fr>
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As bi_end_io is only called once when the reqeust is complete,
the 'size' argument is now redundant. Remove it.
Now there is no need for bio_endio to subtract the size completed
from bi_size. So don't do that either.
While we are at it, change bi_end_io to return void.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
1/ ops_complete_biofill tried to avoid calling handle_stripe since all the
state necessary to return read completions is available. However the
process of determining whether more read requests are pending requires
locking the stripe (to block add_stripe_bio from updating dev->toead).
ops_complete_biofill can run in tasklet context, so rather than upgrading
all the stripe locks from spin_lock to spin_lock_bh this patch just
unconditionally reschedules handle_stripe after completing the read
request.
2/ ops_complete_biofill needlessly qualified processing R5_Wantfill with
dev->toread. The result being that the 'biofill' pending bit is cleared
before handling the pending read-completions on dev->read. R5_Wantfill can
be unconditionally handled because the 'biofill' pending bit prevents new
R5_Wantfill requests from being seen by ops_run_biofill and
ops_complete_biofill.
Found-by: Yuri Tikhonov <yur@emcraft.com>
[neilb@suse.de: simpler fix for bug 1 than moving code]
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
The recent changed to raid5 to allow offload of parity calculation etc
introduced some bugs in the code for growing (i.e. adding a disk to) raid5
and raid6. This fixes them
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Andrew Morton:
[async_memcpy] is very wrong if both ASYNC_TX_KMAP_DST and
ASYNC_TX_KMAP_SRC can ever be set. We'll end up using the same kmap
slot for both src add dest and we get either corrupted data or a BUG.
Evgeniy Polyakov:
Btw, shouldn't it always be kmap_atomic() even if flag is not set.
That pages are usual one returned by alloc_page().
So fix the usage of kmap_atomic and kill the ASYNC_TX_KMAP_DST and
ASYNC_TX_KMAP_SRC flags.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I/O submission requests were already handled outside of the stripe lock in
handle_stripe. Now that handle_stripe is only tasked with finding work,
this logic belongs in raid5_run_ops.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
When a stripe is being expanded bulk copying takes place to move the data
from the old stripe to the new. Since raid5_run_ops only operates on one
stripe at a time these bulk copies are handled in-line under the stripe
lock. In the dma offload case we poll for the completion of the operation.
After the data has been copied into the new stripe the parity needs to be
recalculated across the new disks. We reuse the existing postxor
functionality to carry out this calculation. By setting STRIPE_OP_POSTXOR
without setting STRIPE_OP_BIODRAIN the completion path in handle stripe
can differentiate expand operations from normal write operations.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
When a read bio is attached to the stripe and the corresponding block is
marked R5_UPTODATE, then a read (biofill) operation is scheduled to copy
the data from the stripe cache to the bio buffer. handle_stripe flags the
blocks to be operated on with the R5_Wantfill flag. If new read requests
arrive while raid5_run_ops is running they will not be handled until
handle_stripe is scheduled to run again.
Changelog:
* cleanup to_read and to_fill accounting
* do not fail reads that have reached the cache
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
Check operations are scheduled when the array is being resynced or an
explicit 'check/repair' command was sent to the array. Previously check
operations would destroy the parity block in the cache such that even if
parity turned out to be correct the parity block would be marked
!R5_UPTODATE at the completion of the check. When the operation can be
carried out by a dma engine the assumption is that it can check parity as a
read-only operation. If raid5_run_ops notices that the check was handled
by hardware it will preserve the R5_UPTODATE status of the parity disk.
When a check operation determines that the parity needs to be repaired we
reuse the existing compute block infrastructure to carry out the operation.
Repair operations imply an immediate write back of the data, so to
differentiate a repair from a normal compute operation the
STRIPE_OP_MOD_REPAIR_PD flag is added.
Changelog:
* remove test_and_set/test_and_clear BUG_ONs, Neil Brown
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
handle_stripe will compute a block when a backing disk has failed, or when
it determines it can save a disk read by computing the block from all the
other up-to-date blocks.
Previously a block would be computed under the lock and subsequent logic in
handle_stripe could use the newly up-to-date block. With the raid5_run_ops
implementation the compute operation is carried out a later time outside
the lock. To preserve the old functionality we take advantage of the
dependency chain feature of async_tx to flag the block as R5_Wantcompute
and then let other parts of handle_stripe operate on the block as if it
were up-to-date. raid5_run_ops guarantees that the block will be ready
before it is used in another operation.
However, this only works in cases where the compute and the dependent
operation are scheduled at the same time. If a previous call to
handle_stripe sets the R5_Wantcompute flag there is no facility to pass the
async_tx dependency chain across successive calls to raid5_run_ops. The
req_compute variable protects against this case.
Changelog:
* remove the req_compute BUG_ON
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
After handle_stripe5 decides whether it wants to perform a
read-modify-write, or a reconstruct write it calls
handle_write_operations5. A read-modify-write operation will perform an
xor subtraction of the blocks marked with the R5_Wantprexor flag, copy the
new data into the stripe (biodrain) and perform a postxor operation across
all up-to-date blocks to generate the new parity. A reconstruct write is run
when all blocks are already up-to-date in the cache so all that is needed
is a biodrain and postxor.
On the completion path STRIPE_OP_PREXOR will be set if the operation was a
read-modify-write. The STRIPE_OP_BIODRAIN flag is used in the completion
path to differentiate write-initiated postxor operations versus
expansion-initiated postxor operations. Completion of a write triggers i/o
to the drives.
Changelog:
* make the 'rcw' parameter to handle_write_operations5 a simple flag, Neil Brown
* remove test_and_set/test_and_clear BUG_ONs, Neil Brown
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
All the handle_stripe operations that are to be transitioned to use
raid5_run_ops need a method to coherently gather work under the stripe-lock
and hand that work off to raid5_run_ops. The 'get_stripe_work' routine
runs under the lock to read all the bits in sh->ops.pending that do not
have the corresponding bit set in sh->ops.ack. This modified 'pending'
bitmap is then passed to raid5_run_ops for processing.
The transition from 'ack' to 'completion' does not need similar protection
as the existing release_stripe infrastructure will guarantee that
handle_stripe will run again after a completion bit is set, and
handle_stripe can tolerate a sh->ops.completed bit being set while the lock
is held.
A call to async_tx_issue_pending_all() is added to raid5d to kick the
offload engines once all pending stripe operations work has been submitted.
This enables batching of the submission and completion of operations.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
When the raid acceleration work was proposed, Neil laid out the following
attack plan:
1/ move the xor and copy operations outside spin_lock(&sh->lock)
2/ find/implement an asynchronous offload api
The raid5_run_ops routine uses the asynchronous offload api (async_tx) and
the stripe_operations member of a stripe_head to carry out xor+copy
operations asynchronously, outside the lock.
To perform operations outside the lock a new set of state flags is needed
to track new requests, in-flight requests, and completed requests. In this
new model handle_stripe is tasked with scanning the stripe_head for work,
updating the stripe_operations structure, and finally dropping the lock and
calling raid5_run_ops for processing. The following flags outline the
requests that handle_stripe can make of raid5_run_ops:
STRIPE_OP_BIOFILL
- copy data into request buffers to satisfy a read request
STRIPE_OP_COMPUTE_BLK
- generate a missing block in the cache from the other blocks
STRIPE_OP_PREXOR
- subtract existing data as part of the read-modify-write process
STRIPE_OP_BIODRAIN
- copy data out of request buffers to satisfy a write request
STRIPE_OP_POSTXOR
- recalculate parity for new data that has entered the cache
STRIPE_OP_CHECK
- verify that the parity is correct
STRIPE_OP_IO
- submit i/o to the member disks (note this was already performed outside
the stripe lock, but it made sense to add it as an operation type
The flow is:
1/ handle_stripe sets STRIPE_OP_* in sh->ops.pending
2/ raid5_run_ops reads sh->ops.pending, sets sh->ops.ack, and submits the
operation to the async_tx api
3/ async_tx triggers the completion callback routine to set
sh->ops.complete and release the stripe
4/ handle_stripe runs again to finish the operation and optionally submit
new operations that were previously blocked
Note this patch just defines raid5_run_ops, subsequent commits (one per
major operation type) modify handle_stripe to take advantage of this
routine.
Changelog:
* removed ops_complete_biodrain in favor of ops_complete_postxor and
ops_complete_write.
* removed the raid5_run_ops workqueue
* call bi_end_io for reads in ops_complete_biofill, saves a call to
handle_stripe
* explicitly handle the 2-disk raid5 case (xor becomes memcpy), Neil Brown
* fix race between async engines and bi_end_io call for reads, Neil Brown
* remove unnecessary spin_lock from ops_complete_biofill
* remove test_and_set/test_and_clear BUG_ONs, Neil Brown
* remove explicit interrupt handling for channel switching, this feature
was absorbed (i.e. it is now implicit) by the async_tx api
* use return_io in ops_complete_biofill
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
Replaces PRINTK with pr_debug, and kills the RAID5_DEBUG definition in
favor of the global DEBUG definition. To get local debug messages just add
'#define DEBUG' to the top of the file.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
handle_stripe5 and handle_stripe6 have very deep logic paths handling the
various states of a stripe_head. By introducing the 'stripe_head_state'
and 'r6_state' objects, large portions of the logic can be moved to
sub-routines.
'struct stripe_head_state' consumes all of the automatic variables that previously
stood alone in handle_stripe5,6. 'struct r6_state' contains the handle_stripe6
specific variables like p_failed and q_failed.
One of the nice side effects of the 'stripe_head_state' change is that it
allows for further reductions in code duplication between raid5 and raid6.
The following new routines are shared between raid5 and raid6:
handle_completed_write_requests
handle_requests_to_failed_array
handle_stripe_expansion
Changes:
* v2: fixed 'conf->raid_disk-1' for the raid6 'handle_stripe_expansion' path
* v3: removed the unused 'dirty' field from struct stripe_head_state
* v3: coalesced open coded bi_end_io routines into return_io()
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
The async_tx api provides methods for describing a chain of asynchronous
bulk memory transfers/transforms with support for inter-transactional
dependencies. It is implemented as a dmaengine client that smooths over
the details of different hardware offload engine implementations. Code
that is written to the api can optimize for asynchronous operation and the
api will fit the chain of operations to the available offload resources.
I imagine that any piece of ADMA hardware would register with the
'async_*' subsystem, and a call to async_X would be routed as
appropriate, or be run in-line. - Neil Brown
async_tx exploits the capabilities of struct dma_async_tx_descriptor to
provide an api of the following general format:
struct dma_async_tx_descriptor *
async_<operation>(..., struct dma_async_tx_descriptor *depend_tx,
dma_async_tx_callback cb_fn, void *cb_param)
{
struct dma_chan *chan = async_tx_find_channel(depend_tx, <operation>);
struct dma_device *device = chan ? chan->device : NULL;
int int_en = cb_fn ? 1 : 0;
struct dma_async_tx_descriptor *tx = device ?
device->device_prep_dma_<operation>(chan, len, int_en) : NULL;
if (tx) { /* run <operation> asynchronously */
...
tx->tx_set_dest(addr, tx, index);
...
tx->tx_set_src(addr, tx, index);
...
async_tx_submit(chan, tx, flags, depend_tx, cb_fn, cb_param);
} else { /* run <operation> synchronously */
...
<operation>
...
async_tx_sync_epilog(flags, depend_tx, cb_fn, cb_param);
}
return tx;
}
async_tx_find_channel() returns a capable channel from its pool. The
channel pool is organized as a per-cpu array of channel pointers. The
async_tx_rebalance() routine is tasked with managing these arrays. In the
uniprocessor case async_tx_rebalance() tries to spread responsibility
evenly over channels of similar capabilities. For example if there are two
copy+xor channels, one will handle copy operations and the other will
handle xor. In the SMP case async_tx_rebalance() attempts to spread the
operations evenly over the cpus, e.g. cpu0 gets copy channel0 and xor
channel0 while cpu1 gets copy channel 1 and xor channel 1. When a
dependency is specified async_tx_find_channel defaults to keeping the
operation on the same channel. A xor->copy->xor chain will stay on one
channel if it supports both operation types, otherwise the transaction will
transition between a copy and a xor resource.
Currently the raid5 implementation in the MD raid456 driver has been
converted to the async_tx api. A driver for the offload engines on the
Intel Xscale series of I/O processors, iop-adma, is provided in a later
commit. With the iop-adma driver and async_tx, raid456 is able to offload
copy, xor, and xor-zero-sum operations to hardware engines.
On iop342 tiobench showed higher throughput for sequential writes (20 - 30%
improvement) and sequential reads to a degraded array (40 - 55%
improvement). For the other cases performance was roughly equal, +/- a few
percentage points. On a x86-smp platform the performance of the async_tx
implementation (in synchronous mode) was also +/- a few percentage points
of the original implementation. According to 'top' on iop342 CPU
utilization drops from ~50% to ~15% during a 'resync' while the speed
according to /proc/mdstat doubles from ~25 MB/s to ~50 MB/s.
The tiobench command line used for testing was: tiobench --size 2048
--block 4096 --block 131072 --dir /mnt/raid --numruns 5
* iop342 had 1GB of memory available
Details:
* if CONFIG_DMA_ENGINE=n the asynchronous path is compiled away by making
async_tx_find_channel a static inline routine that always returns NULL
* when a callback is specified for a given transaction an interrupt will
fire at operation completion time and the callback will occur in a
tasklet. if the the channel does not support interrupts then a live
polling wait will be performed
* the api is written as a dmaengine client that requests all available
channels
* In support of dependencies the api implicitly schedules channel-switch
interrupts. The interrupt triggers the cleanup tasklet which causes
pending operations to be scheduled on the next channel
* Xor engines treat an xor destination address differently than a software
xor routine. To the software routine the destination address is an implied
source, whereas engines treat it as a write-only destination. This patch
modifies the xor_blocks routine to take a an explicit destination address
to mirror the hardware.
Changelog:
* fixed a leftover debug print
* don't allow callbacks in async_interrupt_cond
* fixed xor_block changes
* fixed usage of ASYNC_TX_XOR_DROP_DEST
* drop dma mapping methods, suggested by Chris Leech
* printk warning fixups from Andrew Morton
* don't use inline in C files, Adrian Bunk
* select the API when MD is enabled
* BUG_ON xor source counts <= 1
* implicitly handle hardware concerns like channel switching and
interrupts, Neil Brown
* remove the per operation type list, and distribute operation capabilities
evenly amongst the available channels
* simplify async_tx_find_channel to optimize the fast path
* introduce the channel_table_initialized flag to prevent early calls to
the api
* reorganize the code to mimic crypto
* include mm.h as not all archs include it in dma-mapping.h
* make the Kconfig options non-user visible, Adrian Bunk
* move async_tx under crypto since it is meant as 'core' functionality, and
the two may share algorithms in the future
* move large inline functions into c files
* checkpatch.pl fixes
* gpl v2 only correction
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-By: NeilBrown <neilb@suse.de>
The async_tx api tries to use a dma engine for an operation, but will fall
back to an optimized software routine otherwise. Xor support is
implemented using the raid5 xor routines. For organizational purposes this
routine is moved to a common area.
The following fixes are also made:
* rename xor_block => xor_blocks, suggested by Adrian Bunk
* ensure that xor.o initializes before md.o in the built-in case
* checkpatch.pl fixes
* mark calibrate_xor_blocks __init, Adrian Bunk
Cc: Adrian Bunk <bunk@stusta.de>
Cc: NeilBrown <neilb@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This reverts commit 5b479c91da.
Quoth Neil Brown:
"It causes an oops when auto-detecting raid arrays, and it doesn't
seem easy to fix.
The array may not be 'open' when do_md_run is called, so
bdev->bd_disk might be NULL, so bd_set_size can oops.
This whole approach of opening an md device before it has been
assembled just seems to get more and more painful. I think I'm going
to have to come up with something clever to provide both backward
comparability with usage expectation, and sane integration into the
rest of the kernel."
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
md currently uses ->media_changed to make sure rescan_partitions
is call on md array after they are assembled.
However that doesn't happen until the array is opened, which is later
than some people would like.
So use blkdev_ioctl to do the rescan immediately that the
array has been assembled.
This means we can remove all the ->change infrastructure as it was only used
to trigger a partition rescan.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB doesn't like slashes as it wants to use the cache name as the name of a
directory (or symlink) in sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... still not sure why we need this ....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If this mddev and queue got reused for another array that doesn't register a
congested_fn, this function would get called incorretly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All that is missing the the function pointers in raid4_pers.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.
Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks". With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar. One place was missed.
This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong. On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i.e. one or more drives can be added and the array will re-stripe
while on-line.
Most of the interesting work was already done for raid5. This just extends it
to raid6.
mdadm newer than 2.6 is needed for complete safety, however any version of
mdadm which support raid5 reshape will do a good enough job in almost all
cases (an 'echo repair > /sys/block/mdX/md/sync_action' is recommended after a
reshape that was aborted and had to be restarted with an such a version of
mdadm).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An error always aborts any resync/recovery/reshape on the understanding that
it will immediately be restarted if that still makes sense. However a reshape
currently doesn't get restarted. With this patch it does.
To avoid restarting when it is not possible to do work, we call into the
personality to check that a reshape is ok, and strengthen raid5_check_reshape
to fail if there are too many failed devices.
We also break some code out into a separate function: remove_and_add_spares as
the indent level for that code was getting crazy.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible for raid5 to be sent a bio that is too big for an underlying
device. So if it is a READ that we pass stright down to a device, it will
fail and confuse RAID5.
So in 'chunk_aligned_read' we check that the bio fits within the parameters
for the target device and if it doesn't fit, fall back on reading through
the stripe cache and making lots of one-page requests.
Note that this is the earliest time we can check against the device because
earlier we don't have a lock on the device, so it could change underneath
us.
Also, the code for handling a retry through the cache when a read fails has
not been tested and was badly broken. This patch fixes that code.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Kai" <epimetreus@fastmail.fm>
Cc: <stable@suse.de>
Cc: <org@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
raid5_mergeable_bvec tries to ensure that raid5 never sees a read request
that does not fit within just one chunk. However as we must always accept
a single-page read, that is not always possible.
So when "in_chunk_boundary" fails, it might be unusual, but it is not a
problem and printing a message every time is a bad idea.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a GFP_KERNEL allocation is attempted in md while the mddev_lock is held,
it is possible for a deadlock to eventuate.
This happens if the array was marked 'clean', and the memalloc triggers a
write-out to the md device.
For the writeout to succeed, the array must be marked 'dirty', and that
requires getting the mddev_lock.
So, before attempting a GFP_KERNEL allocation while holding the lock, make
sure the array is marked 'dirty' (unless it is currently read-only).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks Jens for alerting me to this.
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: <raziebe@gmail.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently raid5 depends on clearing the BIO_UPTODATE flag to signal an error
to higher levels. While this should be sufficient, it is safer to explicitly
set the error code as well - less room for confusion.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some vestiges of old code that was used for bypassing the stripe
cache on reads in raid5.c. This was never updated after the change from
buffer_heads to bios, but was left as a reminder.
That functionality has nowe been implemented in a completely different way, so
the old code can go.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
stripe_to_pdidx finds the index of the parity disk for a given stripe. It
assumes raid5 in that it uses "disks-1" to determine the number of data disks.
This is incorrect for raid6 but fortunately the two usages cancel each other
out. The only way that 'data_disks' affects the calculation of pd_idx in
raid5_compute_sector is when it is divided into the sector number. But as
that sector number is calculated by multiplying in the wrong value of
'data_disks' the division produces the right value.
So it is innocuous but needs to be fixed.
Also change the calculation of raid_disks in compute_blocknr to make it
more obviously correct (it seems at first to always use disks-1 too).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call the chunk_aligned_read where appropriate.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a bypass-the-cache read fails, we simply try again through the cache. If
it fails again it will trigger normal recovery precedures.
update 1:
From: NeilBrown <neilb@suse.de>
1/
chunk_aligned_read and retry_aligned_read assume that
data_disks == raid_disks - 1
which is not true for raid6.
So when an aligned read request bypasses the cache, we can get the wrong data.
2/ The cloned bio is being used-after-free in raid5_align_endio
(to test BIO_UPTODATE).
3/ We forgot to add rdev->data_offset when submitting
a bio for aligned-read
4/ clone_bio calls blk_recount_segments and then we change bi_bdev,
so we need to invalidate the segment counts.
5/ We don't de-reference the rdev when the read completes.
This means we need to record the rdev to so it is still
available in the end_io routine. Fortunately
bi_next in the original bio is unused at this point so
we can stuff it in there.
6/ We leak a cloned bio if the target rdev is not usable.
From: NeilBrown <neilb@suse.de>
update 2:
1/ When aligned requests fail (read error) they need to be retried
via the normal method (stripe cache). As we cannot be sure that
we can process a single read in one go (we may not be able to
allocate all the stripes needed) we store a bio-being-retried
and a list of bioes-that-still-need-to-be-retried.
When find a bio that needs to be retried, we should add it to
the list, not to single-bio...
2/ We were never incrementing 'scnt' when resubmitting failed
aligned requests.
[akpm@osdl.org: build fix]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This will encourage read request to be on only one device, so we will often be
able to bypass the cache for read requests.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I forgot to has the size-in-blocks to (loff_t) before shifting up to a
size-in-bytes.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes two if() BUG(); usages to BUG_ON(); so people
can disable it safely.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This is very different from other raid levels and all requests go through a
'stripe cache', and it has congestion management already.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The error handling routines don't use proper locking, and so two concurrent
errors could trigger a problem.
So:
- use test-and-set and test-and-clear to synchonise
the In_sync bits with the ->degraded count
- use the spinlock to protect updates to the
degraded count (could use an atomic_t but that
would be a bigger change in code, and isn't
really justified)
- remove un-necessary locking in raid5
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They are not needed. conf->failed_disks is the same as mddev->degraded and
conf->working_disks is conf->raid_disks - mddev->degraded.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is generally useful, but particularly helps see if it is the same sector
that always needs correcting, or different ones.
[akpm@osdl.org: fix printk warnings]
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The comment gives more details, but I didn't quite have the sequencing write,
so there was room for races to leave bits unset in the on-disk bitmap for
short periods of time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a device is unplugged, requests are moved from one or two (depending on
whether a bitmap is in use) queues to the main request queue.
So whenever requests are put on either of those queues, we should make sure
the raid5 array is 'plugged'. However we don't. We currently plug the raid5
queue just before putting requests on queues, so there is room for a race. If
something unplugs the queue at just the wrong time, requests will be left on
the queue and nothing will want to unplug them. Normally something else will
plug and unplug the queue fairly soon, but there is a risk that nothing will.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I have reports of a problem with raid5 which turns out to be because the raid5
device gets stuck in a 'plugged' state. This shouldn't be able to happen as
3msec after it gets plugged it should get unplugged. However it happens
none-the-less. This patch fixes the problem and is a reasonable thing to do,
though it might hurt performance slightly in some cases.
Until I can find the real problem, we should probably have this workaround in
place.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As data_disks is *less* than raid_disks, the current test here is obviously
wrong. And as the difference is already available in conf->max_degraded, it
makes much more sense to use that.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as raid5 sync_request is WAY too big.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a lot of commonality between raid5.c and raid6main.c. This patches
merges both into one module called raid456. This saves a lot of code, and
paves the way for online raid5->raid6 migrations.
There is still duplication, e.g. between handle_stripe5 and handle_stripe6.
This will probably be cleaned up later.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The largest chunk size the code can support without substantial surgery is
2^30 bytes, so make that the limit instead of an arbitrary 4Meg. Some day,
the 'chunksize' should change to a sector-shift instead of a byte-count. Then
no limit would be needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this changes if() BUG(); constructs to BUG_ON() which is
cleaner and can better optimized away
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
raid5 overloads bi_phys_segments to count the number of blocks that the
request was broken in to so that it knows when the bio is completely handled.
Accessing this must always be done under a spinlock. In one case we also call
bi_end_io under that spinlock, which probably isn't ideal as bi_end_io could
be expensive (even though it isn't allowed to sleep).
So we reducde the range of the spinlock to just accessing bi_phys_segments.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
wait_event_lock_irq puts a ';' after its usage of the 4th arg, so we don't
need to.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of checkpointing at each stripe, only checkpoint when a new write
would overwrite uncheckpointed data. Block any write to the uncheckpointed
area. Arbitrarily checkpoint at least every 3Meg.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We allow the superblock to record an 'old' and a 'new' geometry, and a
position where any conversion is up to. The geometry allows for changing
chunksize, layout and level as well as number of devices.
When using verion-0.90 superblock, we convert the version to 0.91 while the
conversion is happening so that an old kernel will refuse the assemble the
array. For version-1, we use a feature bit for the same effect.
When starting an array we check for an incomplete reshape and restart the
reshape process if needed. If the reshape stopped at an awkward time (like
when updating the first stripe) we refuse to assemble the array, and let
user-space worry about it.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds raid5_reshape and end_reshape which will start and finish the
reshape processes.
raid5_reshape is only enabled in CONFIG_MD_RAID5_RESHAPE is set, to discourage
accidental use.
Read the 'help' for the CONFIG_MD_RAID5_RESHAPE entry.
and Make sure that you have backups, just in case.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the core of the resize/expand process.
sync_request notices if a 'reshape' is happening and acts accordingly.
It allocated new stripe_heads for the next chunk-wide-stripe in the target
geometry, marking them STRIPE_EXPANDING.
Then it finds which stripe heads in the old geometry can provide data needed
by these and marks them STRIPE_EXPAND_SOURCE. This causes stripe_handle to
read all blocks on those stripes.
Once all blocks on a STRIPE_EXPAND_SOURCE stripe_head are read, any that are
needed are copied into the corresponding STRIPE_EXPANDING stripe_head. Once a
STRIPE_EXPANDING stripe_head is full, it is marks STRIPE_EXPAND_READY and then
is written out and released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to allow that different stripes are of different effective sizes, and
use the appropriate size. Also, when a stripe is being expanded, we must
block any IO attempts until the stripe is stable again.
Key elements in this change are:
- each stripe_head gets a 'disk' field which is part of the key,
thus there can sometimes be two stripe heads of the same area of
the array, but covering different numbers of devices. One of these
will be marked STRIPE_EXPANDING and so won't accept new requests.
- conf->expand_progress tracks how the expansion is progressing and
is used to determine whether the target part of the array has been
expanded yet or not.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before a RAID-5 can be expanded, we need to be able to expand the stripe-cache
data structure.
This requires allocating new stripes in a new kmem_cache. If this succeeds,
we copy cache pages over and release the old stripes and kmem_cache.
We then allocate new pages. If that fails, we leave the stripe cache at it's
new size. It isn't worth the effort to shrink it back again.
Unfortuanately this means we need two kmem_cache names as we, for a short
period of time, we have two kmem_caches. So they are raid5/%s and
raid5/%s-alt
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The remainder of this batch implements raid5 reshaping. Currently the only
shape change that is supported is added a device, but it is envisioned that
changing the chunksize and layout will also be supported, as well as changing
the level (e.g. 1->5, 5->6).
The reshape process naturally has to move all of the data in the array, and so
should be used with caution. It is believed to work, and some testing does
support this, but wider testing would be great for increasing my confidence.
You will need a version of mdadm newer than 2.3.1 to make use of raid5 growth.
This is because mdadm need to take a copy of a 'critical section' at the
start of the array incase there is a crash at an awkward moment. On restart,
mdadm will restore the critical section and allow reshape to continue.
I hope to release a 2.4-pre by early next week - it still needs a little more
polishing.
This patch:
Previously the array of disk information was included in the raid5 'conf'
structure which was allocated to an appropriate size. This makes it awkward
to change the size of that array. So we split it off into a separate
kmalloced array which will require a little extra indexing, but is much easier
to grow.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- version-1 superblock
+ The default_bitmap_offset is in sectors, not bytes.
+ the 'size' field in the superblock is in sectors, not KB
- raid0_run should return a negative number on error, not '1'
- raid10_read_balance should not return a valid 'disk' number if
->rdev turned out to be NULL
- kmem_cache_destroy doesn't like being passed a NULL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "inline" keyword from a bunch of big functions in the kernel with
the goal of shrinking it by 30kb to 40kb
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Store this total in superblock (As appropriate), and make it available to
userspace via sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md supports multiple different RAID level, each being implemented by a
'personality' (which is often in a separate module).
These personalities have fairly artificial 'numbers'. The numbers
are use to:
1- provide an index into an array where the various personalities
are recorded
2- identify the module (via an alias) which implements are particular
personality.
Neither of these uses really justify the existence of personality numbers.
The array can be replaced by a linked list which is searched (array lookup
only happens very rarely). Module identification can be done using an alias
based on level rather than 'personality' number.
The current 'raid5' modules support two level (4 and 5) but only one
personality. This slight awkwardness (which was handled in the mapping from
level to personality) can be better handled by allowing raid5 to register 2
personalities.
With this change in place, the core md module does not need to have an
exhaustive list of all possible personalities, so other personalities can be
added independently.
This patch also moves the check for chunksize being non-zero into the ->run
routines for the personalities that need it, rather than having it in core-md.
This has a side effect of allowing 'faulty' and 'linear' not to have a
chunk-size set.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- replace open-coded hash chain with hlist macros
- Fix hash-table size at one page - it is already quite generous, so there
will never be a need to use multiple pages, so no need for __get_free_pages
No functional change.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace multiple kmalloc/memset pairs with kzalloc calls.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Substitute:
page_cache_get -> get_page
page_cache_release -> put_page
PAGE_CACHE_SHIFT -> PAGE_SHIFT
PAGE_CACHE_SIZE -> PAGE_SIZE
PAGE_CACHE_MASK -> PAGE_MASK
__free_page -> put_page
because we aren't using the page cache, we are just using pages.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is this "FIXME" comment with a typo in it!! that been annoying me for
days, so I just had to remove it.
conf->disks[i].rdev should only be accessed if
- we know we hold a reference or
- the mddev->reconfig_sem is down or
- we have a rcu_readlock
handle_stripe was referencing rdev in three places without any of these. For
the first two, get an rcu_readlock. For the last, the same access
(md_sync_acct call) is made a little later after the rdev has been claimed
under and rcu_readlock, if R5_Syncio is set. So just use that access...
However R5_Syncio isn't really needed as the 'syncing' variable contains the
same information. So use that instead.
Issues, comment, and fix are identical in raid5 and raid6.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is important because bitmap_create uses
mddev->resync_max_sectors
and that doesn't have a valid value until after the array
has been initialised (with pers->run()).
[It doesn't make a difference for current personalities that
support bitmaps, but will make a difference for raid10]
This has the added advantage of meaning with can move the thread->timeout
manipulation inside the bitmap.c code instead of sprinkling identical code
throughout all personalities.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
See patch to md.txt for more details
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Resync code:
A test that isn't needed,
a 'compute_block' that makes more sense
elsewhere (And then doesn't need a test),
a couple of BUG_ONs to confirm the change makes sense.
Printks:
A few were missing KERN_*
Also fix a typo in a comment..
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The raid5 stripe cache was recently changed from fixed size (NR_STRIPES) to
variable size (conf->max_nr_stripes). However there are two places that still
use the constant and as a result, reducing the size of the stripe cache can
result in a deadlock.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
bitmap_unplug actually writes data (bits) to storage, so we shouldn't be
holding a spinlock...
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1/ I really should be using the __ATTR macros for defining attributes, so
that the .owner field get set properly, otherwise modules can be removed
while sysfs files are open. This also involves some name changes of _show
routines.
2/ Always lock the mddev (against reconfiguration) for all sysfs attribute
access. This easily avoid certain races and is completely consistant with
other interfaces (ioctl and /proc/mdstat both always lock against
reconfiguration).
3/ raid5 attributes must check that the 'conf' structure actually exists
(the array could have been stopped while an attribute file was open).
4/ A missing 'kfree' from when the raid5_conf_t was converted to have a
kobject embedded, and then converted back again.
Signed-off-by: Neil Brown <neilb@suse.de>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A sync of raid5 usually ignore blocks which the bitmap says are in-sync. But
a user-request check or repair should not ignore these.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has the advantage of removing the confusion caused by 'rdev_t' and
'mddev_t' both having 'in_sync' fields.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Two refinements to the 'attempt-overwrite-on-read-error' mechanism.
1/ If the array is read-only, don't attempt an over-write.
2/ If there are more than max_nr_stripes read errors on a device with
no success, fail the drive. This will make sure a dead
drive will be eventually kicked even when we aren't trying
to rewrite (which would normally kick a dead drive more quickly.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There isn't really a need for raid5 attributes to be an a subdirectory,
so this patch moves them from
/sys/block/mdX/md/raid5/attribute
to
/sys/block/mdX/md/attribute
This suggests that all md personalities should co-operate about
namespace usage, but that shouldn't be a problem.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With this, raid5 can be asked to check parity without repairing it. It also
keeps a count of the number of incorrect parity blocks found (mismatches) and
reports them through sysfs.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
/sys/block/mdX/md/raid5/
contains raid5-related attributes.
Currently
stripe_cache_size
is number of entries in stripe cache, and is settable.
stripe_cache_active
is number of active entries, and in only readable.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes the behaviour of raid5 when it gets a read error.
Instead of just failing the device, it tried to find out what should have
been there, and writes it over the bad block. For some media-errors, this
has a reasonable chance of fixing the error. If the write succeeds, and a
subsequent read succeeds as well, raid5 decided the address is OK and
conitnues.
Instead of failing a drive on read-error, we attempt to re-write the block,
and then re-read. If that all works, we allow the device to remain in the
array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_interruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of having ->read_sectors and ->write_sectors, combine the two
into ->sectors[2] and similar for the other fields. This saves a branch
several places in the io path, since we don't have to care for what the
actual io direction is. On my x86-64 box, that's 200 bytes less text in
just the core (not counting the various drivers).
Signed-off-by: Jens Axboe <axboe@suse.de>
Most awkward part of this is delaying write requests until bitmap updates have
been flushed.
To achieve this, we have a sequence number (seq_flush) which is incremented
each time the raid5 is unplugged.
If the raid thread notices that this has changed, it flushes bitmap changes,
and assigned the value of seq_flush to seq_write.
When a write request arrives, it is given the number from seq_write, and that
write request may not complete until seq_flush is larger than the saved seq
number.
We have a new queue for storing stripes which are waiting for a bitmap flush
and an extra flag for stripes to record if the write was 'degraded' and so
should not clear the a bit in the bitmap.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md does not yet support BIO_RW_BARRIER, so be honest about it and fail
(-EOPNOTSUPP) any such requests.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The default resync_max_sector is set to "mddev->size << 1". If the
raid-personality-module updates mddev->size, it must update
resync_max_sectors too.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this, and attempt to 'grow' an array will claim to have synced the
extra part without actually having done anything.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Before completing a 'write' the md superblock might need to be updated.
This is best done by the md_thread.
The current code schedules this up and queues the write request for later
handling by the md_thread.
However some personalities (Raid5/raid6) will deadlock if the md_thread
tries to submit requests to its own array.
So this patch changes things so the processes submitting the request waits
for the superblock to be written and then submits the request itself.
This fixes a recently-created deadlock in raid5/raid6
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1/ change the return value (which is number-of-sectors synced)
from 'int' to 'sector_t'.
The number of sectors is usually easily small enough to fit
in an int, but if resync needs to abort, it may want to return
the total number of remaining sectors, which could be large.
Also errors cannot be returned as negative numbers now, so use
0 instead
2/ Add a 'skipped' return parameter to allow the array to report
that it skipped the sectors. This allows md to take this into account
in the speed calculations.
Currently there is no important skipping, but the bitmap-based-resync
that is coming will use this.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When md marks the superblock dirty before a write, it calls
generic_make_request (to write the superblock) from within
generic_make_request (to write the first dirty block), which could cause
problems later.
With this patch, the superblock write is always done by the helper thread, and
write request are delayed until that write completes.
Also, the locking around marking the array dirty and writing the superblock is
improved to avoid possible races.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md_enter_safemode checks if it is time to mark the md superblock as 'clean'.
i.e. if all writes have completed and a suitable delay has passed.
This is currently called from md_handle_safemode which in-turn is called
(almost) every time md_check_recovery is called, and from the end of
md_do_sync which causes the mddev->thread to run, which will always call
md_check_recovery as well.
So it doesn't need to be a separate function and fits quite well into
md_check_recovery.
The "almost" is because multipathd calls md_check_recovery but not
md_handle_safemode. This is OK because the code from md_enter_safemode is a
no-op if mddev->safemode == 0, which it always is for a multipathd (providing
we don't allow it to be set to 2 on a signal...)
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We we set the too early, they may still be in place and possibly get called
even though the array didn't get set up properly.
Signed-off-by: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes calls to synchronize_kernel(), deprecated in the earlier
"Deprecate synchronize_kernel, GPL replacement" patch to instead call the new
synchronize_rcu() and synchronize_sched() APIs.
Signed-off-by: Paul E. McKenney <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
Bernd Schubert