There's a special branch in the set_tdm_slot op for the case of nslots
being 1, but:
(1) That branch can never work (there's a check for tx_mask being
non-zero, later there's another check for it *being* zero; one or
the other always throws -EINVAL).
(2) The intention of the branch seems to be what the general other
branch reduces to in case of nslots being 1.
For those reasons remove the 'nslots being 1' special case.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Suggested-by: Jos Dehaes <jos.dehaes@gmail.com>
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20221027095800.16094-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the PWR_CTRL field is modeled as the power state of the DAC
widget, and at the same time it is used to implement mute/unmute, we
need some additional book-keeping to have the right end result no matter
the sequence of calls. Without this fix, one permanently mutes an
ongoing stream by toggling the associated speaker pin control.
(This mirrors commit 1e5907bcb3 ("ASoC: tas2770: Fix handling of
mute/unmute") which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220825140241.53963-4-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver is setting the PWR_CTRL field in both the set_bias_level
callback and on DAPM events of the DAC widget (and also in the
mute_stream method). Drop the set_bias_level callback altogether as the
power setting it does is in conflict with the other code paths.
(This mirrors commit c8a6ae3fe1c8 ("ASoC: tas2770: Drop conflicting
set_bias_level power setting") which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220825140241.53963-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The part is a mono speaker amp, but it can do downmix and switch between
left and right channel, so the right channel range is 1 to 2.
(This mirrors commit bf54d97a83 ("ASoC: tas2770: Allow mono streams")
which was a fix to the tas2770 driver.)
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220825140241.53963-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The register default is 0x28 per the datasheet, and the amp gain field
is supposed to be shifted left by one. With the wrong default, the ALSA
controls lie about the power-up state. With the wrong shift, we get only
half the gain we expect.
Signed-off-by: Hector Martin <marcan@marcan.st>
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-4-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
DVC value 0xc8 is -100dB and 0xc9 is mute; this needs to map to
-100.5dB as far as the dB scale is concerned. Fix that and enable
the mute flag, so alsamixer correctly shows the control as
<0 dB .. -100 dB, mute>.
Signed-off-by: Hector Martin <marcan@marcan.st>
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-3-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix setting of FSYNC polarity in case of LEFT_J and DSP_A/B formats.
Do NOT set the SCFG field as was previously done, because that is not
correct and is also in conflict with the "ASI1 Source" control which
sets the same SCFG field!
Also add support for explicit polarity inversion.
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-2-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Make sure there is at least 1 ms delay from reset to first command as
is specified in the datasheet. This is a fix similar to commit
307f314520 ("ASoC: tas2770: Insert post reset delay").
Fixes: 827ed8a0fa ("ASoC: tas2764: Add the driver for the TAS2764")
Signed-off-by: Martin Povišer <povik+lin@cutebit.org>
Link: https://lore.kernel.org/r/20220630075135.2221-1-povik+lin@cutebit.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The ASoC core has now been changed to default to the non-legacy DAI
naming, as such drivers using the new scheme no longer need to specify
the non_legacy_dai_naming flag.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20220623125250.2355471-61-ckeepax@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The i2c probe functions here don't use the id information provided in
their second argument, so the single-parameter i2c probe function
("probe_new") can be used instead.
This avoids scanning the identifier tables during probes.
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220405165836.2165310-11-steve@sk2.org
Signed-off-by: Mark Brown <broonie@kernel.org>
The snd_soc_dai_ops structures is only stored in the ops field of a
snd_soc_dai_driver structure, so make the snd_soc_dai_ops structure
const to allow the compiler to put it in read-only memory.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Ye Bin <yebin10@huawei.com>
Link: https://lore.kernel.org/r/20210408062643.802908-1-yebin10@huawei.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce the Texas Instruments TAS2764 amplifier driver
with I/V sense for loud speaker applications.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Link: https://lore.kernel.org/r/20201007155341.10139-2-dmurphy@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Martin Povišer