TC Applied Technologies (TCAT) produces TCD3070 as final DICE ASIC for
communication in IEEE 1394 bus for IEC 61883-1/6 protocol. As long as I
know, latter model of Focusrite Saffire Pro 40 is an application of the
ASIC and only in the market for consumers.
This patchset adds support for the device. The device has several
remarkable points.
1. No support for extended synchronization information section in TCAT
general protocol. The value of GLOBAL_EXTENDED_STATUS register is always
zero. Additionally, NOTIFY_EXT_STATUS message is never emitted.
2. No support for TCAT protocol extension. Hard coding is required for
format of CIP payload.
3. During several seconds after changing sampling rate, the block to
process PCM frames is under disfunction. When starting packet streaming
during the state, the block is never function till configuring different
sampling rate and several seconds.
This commit adds support for the device. The item 1 and 2 can be
adaptable, while item 3 is not. It's not preferable that user process
is forced to sleep during the disfunction in the call of ioctl(2) with
SNDRV_PCM_IOCTL_HW_PARAMS or SNDRV_PCM_IOCTL_PREPARE request. It's
inconvenient but let user configure preferable sampling rate in advance
of starting PCM substream.
The content of configuration ROM in the device I used is available at:
* https://github.com/takaswie/am-config-roms/
I note that any mixer control operation is implemented by unique
transaction. The frame of request consists of 16 bytes header followed
by payload.
header (4 quadlets):
1st: the type of request, prefixed with 0x8000
2nd: counter at 2 bytes in MSB side, the length of data at 2 bytes in LSB
side
3rd: parameter 0
4th: parameter 1
payload (variable length if need):
5th-: data according to parameters
The request frame is sent by block write request to 0x'ffff'e040'01c0.
The frame of response is similar to the frame of request, but it is
header only, thus fixed to 16 bytes. The response frame is sent to the
address which is registered by lock transaction to 0x'ffff'e040'0008.
If the operation results in batch of data, the 2nd quadlet of header
includes the length of data like request. The data is itself readable
by read block request to 0x'ffff'e040'0030, which includes both
header and payload for data, thus the length to read should be the
length of data plus 16 bytes for header
The actual value of request, parameter 0, parameter 1, and data is
unclear yet.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20221130143313.43880-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The delayed registration of sound card instance brings less benefit than
complication of kobject management. This commit ceases from it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210607081250.13397-5-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
ALSA dice driver detects jumbo payload at high sampling transfer frequency
for below models:
* Avid M-Box 3 Pro
* M-Audio Profire 610
* M-Audio Profire 2626
Although many DICE-based devices have a quirk at high sampling transfer
frequency to multiplex double number of PCM frames into data block than
the number in IEC 61883-1/6, the above devices are just compliant to
IEC 61883-1/6.
This commit disables the mode of double_pcm_frames for the models.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20210518012510.37126-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows ALSA dice driver to share PCM buffer size for both
capture and playback PCM substream. When AMDTP domain starts for one
of the PCM substream, buffer size of the PCM substream is stores to
AMDTP domain structure. Some AMDTP streams have already run with the
buffer size when another PCM substream starts, therefore the PCM
substream has a constraint to its buffer size.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191017155424.885-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit is a preparation to share the size of PCM period between
PCM substreams on AMDTP streams in the same domain. At this time,
the size of PCM period in PCM substream which starts AMDTP streams in the
same domain is recorded.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191007110532.30270-6-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl0jGwUTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LD4B/9AkutfS+vznOrk0V0wFb2SUfjwE4Pr
+z/kAehohAOl/7pg9Dun/lmZYBWMyOM2aYmK81ahEo2DfO+uzwkwjCaXFjGVGwEK
j7XpWkrIjKnou/z1FeALgVvt+crzdy5iNWC04AbKaP2WHCcI7zvPQIsBta/V0OJt
lg+j0J7pagnTMcgV1+qJdaASmofy/hpoZ79Gv0PIfGC8hpJ/3mBgcNPCLQrJtD4R
v+tzvCZNrZVqCanwLf3vouEm1bpWYOpI+Wdmu4u6rY7MhmCj72EJ2zyfdm/qtaxF
e7whgCyOQFkWe7NgDn0G08aAT6LsaxOtPNr7H8tL8S8sw8425fqeOouV
=n/HQ
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.3' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.3
This is a very big update, mainly thanks to Morimoto-san's refactoring
work and some fairly large new drivers.
- Lots more work on moving towards a component based framework from
Morimoto-san.
- Support for force disconnecting muxes from Jerome Brunet.
- New drivers for Cirrus Logic CS47L35, CS47L85 and CS47L90, Conexant
CX2072X, Realtek RT1011 and RT1308.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
>From callbacks for pcm and rawmidi interfaces, the functions to stop
and release duplex streams are called at the same time. This commit
merges the two functions.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Once allocated, isochronous resources are available for packet
streaming, even if the streaming is cancelled. For this reason,
current implementation handles allocation of the resources and
starting packet streaming at the same time. However, this brings
complicated procedure to start packet streaming.
This commit separates the allocation and starting. The allocation is
done in pcm.hw_params callback and available till pcm.hw_free callback.
Even if any XRUN occurs, pcm.prepare callback is done to restart
packet streaming without releasing/allocating the resources.
There are two points to stop packet streaming; in pcm.hw_params and
pcm.prepare callbacks. The former point is a case that packet streaming
is already started for any MIDI substream then packet streaming is
requested with different sampling transfer frequency for any PCM
substream. The latter point is cases of any XRUN or packet queueing
error.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Based on 1 normalized pattern(s):
licensed under the terms of the gnu general public license version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 88 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000437.521539229@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
--nextPart3916812.EicPReet6m
Content-Transfer-Encoding: 7Bit
Content-Type: text/plain; charset="us-ascii"
Mytek manufactures some equipment with DICE-based firewire ports. These
devices contain old versions of DICE firmware which lacks detailed
stream format reporting for all sampling clock modes.
Building upon the recent work by Takashi Sakamoto, hard-coded parameters
are added for the Stereo 192 DSD-DAC. When the device vendor and model
match the coded parameters are copied into the stream format cache.
Signed-off-by: Melvin Vermeeren <mail@mel.vin>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
At present, to add PCM substreams for each of available tx/rx streams,
this driver uses a condition based on model-name. This is not enough
to support unknown models.
In former commits, this driver gains cache of stream formats. For models
which support protocol extension, all of available steam formats are
cached. For known models, hard-coded stream formats are used to generate
the cache. For unknown models, stream formats at current mode of sampling
transmission frequency is cached.
Anyway, at least, the cached formats are used to expose constrains of PCM
substreams for userspace applications. Thus, The cached data can be also
used to add PCM substreams themselves, instead of the name-based
conditions.
This commit obsoletes local frag of force_two_pcms.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TC Applied Technologies (TCAT) have added extension to DICE protocol. This
protocol extension is called as Extended Application Protocol, a.k.a. EAP.
In this protocol extension, units get additional 9 address spaces. One of
it is for current configuration. In this address space, a pair of router
and stream formats are exposed per mode of three sampling transmission
frequencies.
This commit adds support the protocol extension for address space of the
current configuration to generate cache of stream formats.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Alesis shipped some models with DICE ASICs. All of them just support
DICE original protocol and drivers can't retrieve all of available stream
formats without changing status of sampling transmission frequency
actually.
This commit puts some hard-coded parameters for the models. When detecting
the models, the corresponding parameters are copied as cache of stream
formats.
I note that each of pair of iO14/iO26 and MultiMix 8/12/16 has the same
model ID on their configuration ROM. The MultiMix 8/12/16 just support
one mode for sampling transmission frequency and ALSA dice driver already
handles them correctly. The iO14/iO26 support three modes and need
hard-coded parameters. To distinguish these two models, this commit let
the driver to retrieve current stream formats and compare it to known
parameters, then decide it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
TC Electronic shipped some models with DICE ASICs. All of them just support
DICE original protocol and drivers can't retrieve all of available stream
formats without changing status of sampling transmission frequency
actually.
This commit puts some hard-coded parameters for the models. When detecting
the models, the corresponding parameters are copied as cache of stream
formats.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, proxy structure get members for cache of stream
formats. This commit fills the cache with stream formats at current mode
of sampling transmission frequency.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A previous commit 6f688268b3 ('ALSA: dice: purge generating channel
cache') purged cache of stream formats. DICE interface originally has
no feature to assist drivers to retrieve available formats for all of
supported sampling transmission frequencies, without changing the
frequency actually.
For later release of Dice ASICs such as TCD2210, Dice interface has
extended protocol and can support the feature. This assists drivers
to retrieve available stream formats.
This commit is a first step to regain the cache to generate PCM rules
for all of supported sampling transmission frequencies.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix up affected files that include this signal functionality via sched.h.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Some models reduce the number of available isochronous streams for higher
sampling transfer frequency. Such models bring an issue about how to add
PCM substreams. When at lower sampling transfer frequency, the
models reports whole available streams, thus this driver can add enough
number of PCM substreams at probing time. On the other hand, at higher
sampling transfer frequency, this driver can just add reduced number of
PCM substreams. After probed, even if the sampling transfer frequency is
changed to lower rate, fewer PCM substreams are actually available. This
is inconvenience.
For the reason, this commit adds a list so that this driver assume models
on the list to have two pairs of PCM substreams. This list keeps the name
of model in which the number of available streams differs depending on
sampling transfer frequency.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently ALSA dice driver handles a pair of isochronous resources for
IEC 61883-1/6 packet streaming. While, according to some documents about
ASICs named as 'Dice', several isochronous streams are available.
Here, I start to describe ASICs produced under 'Dice' name.
* Dice II (designed by wavefront semiconductor, including TCAT's IP)
* STD (with limited functionality of DTCP)
* CP (with full functionality of DTCP)
* TCD2210/2210-E (so-called 'Dice Mini')
* TCD2220/2220-E (so-called 'Dice Jr.')
* TCD3070-CH (so-called 'Dice III')
Some documents are public and we can see hardware design of them. We can
find some articles about hardware internal register definitions
(not registers exported to IEEE 1394 bus).
* DICE II User Guide
* http://www.tctechnologies.tc/archive/downloads/dice_ii_user_guide.pdf
* 6.1 AVS Audio Receivers
* Table 6.1: AVS Audio Receiver Memory Map
* ARX1-ARX4
* 6.2 AVS Audio Transmitters
* Table 6.2: AVS Audio Transmitter Memory Map
* ATX1, ATX2
* TCD22xx User Guide
* http://www.tctechnologies.tc/downloads/tcd22xx_user_guide.pdf
* 6.1 AVS Audio Receivers
* Table 66: AVS Audio Receiver Memory Map
* ARX1, ARX2
* 6/2 AVS Audio Transmitters
* Table 67: AVS Audio Transmitter Memory Map
* ATX1, ATX2
* DICE III
* http://www.tctechnologies.tc/downloads/TCD3070-CH.pdf
* Dual stream 63 channel transmitter/receiver
For Dice II and TCD22xx series, maximum 16 data channels are transferred in
an AMDTP packet, while for Dice III, maximum 32 data channels are
transferred.
According to the design of the series of these ASICs, this commit allows
this driver to handle additional set of isochronous resources. For
practical reason, two pair of isochronous resources are added. As of this
commit, this driver still use a pair of the first isochronous resources.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In former commits, probing process has no need to set sampling transfer
frequency. Although it's OK to drop a function to change the frequency
from this module, some models require it before streaming. This seems to
be due to phase lock of clock source.
This commit moves the function from transaction layer to stream layer, and
rename it according to the purpose.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dice interface design doesn't allow drivers to read supported combination
between sampling transfer frequencies and the number of Multi bit linear
audio data channels. Due to the design, ALSA dice driver changes current
sampling transfer frequency to generate cache of the combinations at
device probing processing.
Although, this idea is worse because ALSA dice driver changes the state of
clock. This is not what users want when they save favorite configuration
to the device in advance.
Furthermore, there's a possibility that the format of data block is decided
not only according to current sampling transfer frequency, but also the
other factors, i.e. data format for digital interface. It's not good to
generate channel cache according to the sampling transfer frequency only.
This commit purges processing cache data and related structure members. As
a result, users must set preferable sampling transfer frequency before
using ALSA PCM applications, as long as they want to start any PCM
substreams at the rate except for current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some models based on ASIC for Dice II series (STD, CP) change their
hardware configurations after appearing on IEEE 1394 bus. This is due to
interactions of boot loader (RedBoot), firmwares (eCos) and vendor's
configurations. This causes current ALSA dice driver to get wrong
information about the hardware's capability because its probe function
runs just after detecting unit of the model.
As long as I investigated, it takes a bit time (less than 1 second) to load
the firmware after bootstrap. Just after loaded, the driver can get
information about the unit. Then the hardware is initialized according to
vendor's configurations. After, the got information becomes wrong.
Between bootstrap, firmware loading and post configuration, some bus resets
are observed.
This commit offloads most processing of probe function into workqueue and
schedules the workqueue after successive bus resets. This has an effect to
get correct hardware information and avoid involvement to bus reset storm.
For code simplicity, this change effects all of Dice-based models, i.e.
Dice II, Dice Jr., Dice Mini and Dice III.
I use a loose strategy to manage a race condition between the work and the
bus reset. This is due to a specification of dice transaction. When bus
reset occurs, registered address for the transaction is cleared. Drivers
must re-register their own address again. While, this operation is required
for the work because the work includes to wait for the transaction. This
commit uses no lock primitives for the race condition. Instead, checking
'registered' member of 'struct snd_dice' avoid executing the work again.
If sound card is not registered, the work can be scheduled again by bus
reset handler.
When .remove callback is executed, the sound card is going to be released.
The work should not be pending or executed in the releasing. This commit
uses cancel_delayed_work_sync() in .remove callback and wait till the
pending work finished. After .remove callback, .update callback is not
executed, therefore no works are scheduled again.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds data block processing layer for AM824 format. The new
layer initializes streaming layer with its value for fmt field.
Currently, most implementation of data block processing still remains
streaming layer. In later commits, these codes will be moved to the layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In later commit, data block processing layer will be newly added. This
layer will be named as 'amdtp-am824'.
This commit renames current amdtp file to amdtp-stream, to distinguish it
from the new layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a support for MIDI capture/playback
When MIDI substrams already start streaming and PCM substreams are going to
join at different sampling rate, streams are stopped once. Then sampling rate
is changed and streams are restarted.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit allows this driver to handle devices with non SYT-Match
sampling clock source.
When sampling clock source is SYT-Match mode, devices handle
'presentation timestamp' in received packets and generates sampling clock
according to the information. In this case, driver is synchronization master
and must transfer correct value in SYT field of each packets in outgoing
stream, then the outgoing stream is a master stream.
On the other hand, non SYT-Match mode, devices do this. So drivers must pick
up the value in SYT field of incoming packets and use the value for outgoing
stream. Currently firewire-lib module achieve this work.
Furthermore, without SYT-Match and internal clock source, the sampling rate
should be fixed for the other devices connected to the handled device. This
commit add a restriction of sampling rate at this situation.
With these implementations, this driver has no need to set clock source.
This commit remove set function.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds support for AMDTP in-stream. As a result, Dice driver
supports full duplex streams with synchronization.
AMDTP can transfer timestamps in its packets. By handling the timestamp,
devices can synchronize to the other devices or drivers on the same bus.
When Dice chipset is 'enabled', it starts streams with correct settings.
This 'enable' register is global, thus, when a stream is started to run,
an opposite stream can't start unless turning off 'enable'. Therefore
a pair of streams must be running. This causes a loss of CPU usage when
single stream is needed for neither playbacking or capturing.
This commit assumes that playback-only models also have a functionality
to transmit stream for delivering timestamps.
Currently, sampling clock source is restricted to SYT-Match mode. This is
improved in followed commit. I note that at SYT-Match mode, Dice can select
from 4 streams for synchronization but this driver uses the 1st stream only
for simplicity.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Streaming functionality can start streams when rate is given but currently
some codes are in PCM functionality.
This commit changes the way to start stream and add some arrangement
to make it easy to understand the way.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to proc output.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to hwdep functionality.
This interface is designed for mixer/control application. By using hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Additionally, this interface give a way to read Dice notification.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file and move some codes related to PCM functionality.
Currently PCM playback is supported. PCM capture will be supported in followed
commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for streaming, and move some
codes into the file with some arrangements.
Well-known CMP is not used to start/stop streams for Dice chipset. It's
achieved by writing to specific address. We call this way as 'enable'.
When devices are 'enabled', streaming starts in registered isochronous channel.
Some helper functions are already implemented in previous commit.
Basically, the stream is compliant to IEC 61883-6, so-called as AMDTP. But Dice
has a specific quirk, so called-as 'Dual Wire'. This quirk is applied at
176.4/192.0kHz. In this mode, each packet includes double number of events than
number in the specification, and stream runs at a half of sampling rate.
There is another quirk at bus reset. Dice chipset handles drivers' request but
don't re-enable streaming. So stream should be stopped.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This commit adds a file with some helper functions for transaction, and move
some codes into the file with some arrangements.
For Dice chipset, well-known FCP or AV/C commands are not used to control
devices. It's achieved by read/write transactions into specific addresses.
Dice's address area is split into 5 areas. Each area has its own role. The
offset for each area can be got by reading head of the address area. By
reading these areas, drivers can get to know device status. By writing these
areas, drivers can change device status.
Dice has a specific mechanism called as 'notification'. When device status is
changed, Dice devices tells the event by sending transaction. This notification
is sent to an address which drivers register in advance. But this causes an
issue to drivers.
To handle the notification, drivers need to allocate its own callback function
to the address region in host controller. This region is exclusive. For the
other applications, drivers must give a mechanism to read the received
notification. For this purpose, Dice driver already implements hwdep interface.
Dice chipset doesn't allow drivers to register several addresses. In this
reason, when this driver is applied to a device, the other drivers should
_not_ try to register its own address to the device.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Sakamoto