New register area defined in the firmware
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware sets this register with the offset of the firmware trace area
within the peripheral memory region. Critical for the firmware trace
to work
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use single data source for all information regarding the firmware
memory map. With this change "ucode_xxx" regions disappears since
they are in fact part of larger "upper area" region
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If copy_from_user() fails, buffer allocated for parameters would leak
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Variable 'ctx' declarad again in the inner loop. Should use
one from outer loop instead.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New hardware release appears; it require some changes to properly support it.
Introduce struct wil_board and "board" attribute in wil6210_priv;
keep hardware variant information in this structure.
fill it on probe(). Used in the reset flow.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On some platforms, cycles_t is 64-bit, and gcc generates call to
__udivdi3 for straight division of cycles_t/cycles_t. This leads
to compilation failure, as this function is not exist in the kernel
runtime. do_div() to rescue
Original report:
tree: git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next.git master
head: 2e91606f5e
commit: 7c0acf868d [81/103] wil6210: Tx performance monitoring
config: i386-randconfig-ha3-0620 (attached as .config)
All error/warnings:
drivers/built-in.o: In function `wil_vring_debugfs_show':
>> debugfs.c:(.text+0x39b9be): undefined reference to `__udivdi3'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide both event (netif_tx_[stop|wake]) tracking via printk;
and state via debugfs 'info'
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Track number of interrupts and Tx/Rx packets;
expose through debugfs 'info'. Reset upon read.
Used to analyse effectivness of interrupt coalescing and NAPI.
Read twice with some interval like
cat info > /dev/null; sleep 1; cat info
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'info' debugfs entry for misc. assorted information.
Start with indication whether platform is AC-powered;
will use it later for power related decisions
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are platforms where INTx can't be routed by ACPI,
this leads to pci_enable_device failure. Re-try pretending we have
MSI already configured; in this case pci_enable_device do not try
to configure INTx. However, MSI could still work.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As reported by Dan Carpenter <dan.carpenter@oracle.com>:
The patch a715c7ddd65a: "wil6210: improve debug for WMI receive" from
May 29, 2014, leads to the following static checker warning:
drivers/net/wireless/ath/wil6210/wmi.c:746 wmi_recv_cmd()
info: ignoring unreachable code.
drivers/net/wireless/ath/wil6210/wmi.c
739 spin_unlock_irqrestore(&wil->wmi_ev_lock, flags);
740 {
741 int q = queue_work(wil->wmi_wq,
742 &wil->wmi_event_worker);
743 wil_dbg_wmi(wil, "queue_work -> %d\n", q);
744 }
745 }
746 if (n > 1)
^^^^^^^^^^
We never reach this if statemtent.
747 wil_dbg_wmi(wil, "%s -> %d events processed\n", __func__, n);
748 }
Exit loop with "break", not "return".
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
New registers area introduced, mark corresponded address range as valid
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the pcie_bus.c, knowledge about debugfs is not necessary
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the AP-like interface, if "disconnect all" requested,
every station should be deleted with cfg80211_del_sta().
Implement this behavior.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On Tx path, when vring for the destination not found,
it was considered as error and message was printed unconditionally.
However, this situation is normal after disconnect. If disconnect was while
heavy traffic load, lots of Tx packets will be dropped and this would
cause significant amount of prints in dmesg.
Demote messages priority from 'error' to 'debug'.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Expose operational frequency and link info
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print to dmesg when FW error notification is about to be sent
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Interrupt threshold registers may be written to.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Usable for debugging, to be able to obtain FW traces
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For performance monitoring, trace time intervals when Tx vring
is idle/not idle. Use CPU cycle counter for this, because jiffies is
too rough, and other precise time measurement methods involve
overhead while get_cycles() should be fast.
This used to provide some estimation for percentage when Tx vring
was idle, i.e. when hardware is under-utilized.
Estimation is not precise because of many reasons - CPU frequency scaling,
grt_cycles() may be per core etc. But still, it is good estimation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print used/available counters on debugfs;
print to dmesg when Tx vring becomes empty
This aids with performance investigation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
print essential info to dmesg
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wil_cfg80211_start_ap(), debug print selected data:
- beacon (before and after fix-up)
- crypto parameters
- mark start/stop AP invocation
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inform cfg80211 about Tx result
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide 2 files on the debugfs:
- "rxon": write channel (1..4) to open Rx on it, 0 to rxoff
- "tx_mgmt": write binary frame, starting from MAC header
one need to care about turning receiver on/off before/after tx_mgmt
Correct sequence is:
echo $channel > rxon
cat mfmt_frame > tx_mgmt
echo 0 > rxon
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Print message if no events received. This should not happen.
If it is, it points to the problem in firmware.
Track also cases when multiple events processed in one IRQ
Print information as soon as possible - mbox pointers and
event header right after reading it. This helps to identify potential
problem with memory allocation for the event buffer.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of receiving frame with sequence number far greater than current,
wil_release_reorder_frames() will iterate many times over empty buffer.
Optimize this case by checking buffer emptiness and simply update
head_seq_num without iterating.
Suggested-by: Vladimir Shulman <Vladimir.Shulman@Wilocity.com>
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use proper format %pad for the dma_addr_t arguments;
prefix %p with 0x, as %p don't print is by itself
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If scan has not finished in some reasonable time (10sec), interpret it as
if firmware error occurs but was not reported. Firmware should report
scan completion for every scan request, so it is error condition indeed.
Perform firmware recovery procedure.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Provide clear definition of the watermarks for the vring descriptor space.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case there is something fundamentally wrong with the firmware
(example: RF cable disconnected), FW will always crash immediately
after reset. This leads to infinite fw error recovery loop.
Count consecutive unsuccessful error recovery attempts in a short period
of time, and stop doing recovery after some reasonable count.
It is still possible to manually reset fw doing
interface down/up sequence.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Obey 802.11 spec that defines max. data size 7920 bytes
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using scatter-gather, more descriptor entries get used.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes, due to the race between Rx path and WMI_BA_STATUS_EVENTID WMI event,
few frames may be passed to the stack before reorder buffer allocated.
Then, after BACK establishment, it start getting frames with sequence number ahead of
SSN, and it get interpreted as missing frames. Then, BACK mechanism will wait
for missing frames; data traffic will be stopped. In case of interface configured
for DHCP, this data delay causes DHCP failure.
Relax checking for sequence number; use sequence of 1-st frame handled by the buffer
as SSN for this buffer.
This is work-around, real fix should be done when proper BACK mechanism implemented.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
- add pcp_max_assoc_sta to the struct wmi_pcp_start_cmd
- enum for the scan ststus
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reshuffle prints to consolidate firmware/hardware information
report upon card init
Convert print for unhandled MISC ISR bits to "debug" - it is
normal situation and not an "error"
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When disconnecting some CID, corresponded Tx vring get released. During vring
release, all descriptors get freed. It is possible that Tx NAPI working on the same
vring simultaneously. If it happens, descriptor may be double freed.
To protect from the race above, make sure NAPI won't process the same vring.
Introduce 'enabled' flag in the struct vring_tx_data. Proceed with Tx NAPI only if
'enabled' flag set. Prior to Tx vring release, clear this flag and make sure NAPI
get synchronized.
NAPI enablement status protected by wil->mutex, add protection where it was
missing and check for it.
During reset, disconnect all peers first, then proceed with the Rx vring. It allows for
the disconnect flow to observe proper 'wil->status' and correctly notify cfg80211 about
connection status change
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
make sure reset flow executed in order
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use 'real' indication for hardware state.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Vladimir Kondratiev