The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.
If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses the same issue we had for IPv4 where enabling GRE with
an inner checksum cannot be supported with FOU/GUE due to the fact that
they will jump past the GRE header at it is treated like a tunnel header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not include attribute IFLA_GRE_TOS.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix two spots where o_flags in a tunnel are being compared to GRE_SEQ
instead of TUNNEL_SEQ.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to use adjusted protocol value for setting inner protocol.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRE for IPv6 does not properly translate for GRE flags to tunnel
flags and vice versa. This patch fixes that.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's easier for gre_parse_header to return the header length instead of
filing it into a parameter. That way, the callers that don't care about the
header length can just check whether the returned value is lower than zero.
In gre_err, the tunnel header must not be pulled. See commit b7f8fe251e
("gre: do not pull header in ICMP error processing") for details.
This patch reduces the conflict between the mentioned commit and commit
95f5c64c3c ("gre: Move utility functions to common headers").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes in GREv6 transmit path:
- Call gre_checksum, remove gre6_checksum
- Rename ip6gre_xmit2 to __gre6_xmit
- Call gre_build_header utility function
- Call ip6_tnl_xmit common function
- Call ip6_tnl_change_mtu, eliminate ip6gre_tunnel_change_mtu
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Create gre_rcv function. This calls gre_parse_header and ip6gre_rcv.
- Call ip6_tnl_rcv. Doing this and using gre_parse_header eliminates
most of the code in ip6gre_rcv.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code borrowed from bits and pieces of other protocols to
the IPv6 GRE path so that we can support GSO over IPv6 based GRE tunnels.
By adding this support we are able to significantly improve the throughput
for GRE tunnels as we are able to make use of GSO.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the basic offloads we support on most devices.
Specifically with this patch set we can support checksum offload, basic
scatter-gather, and highdma.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we were creating an ip6gretap interface the MTU was about 6 bytes
short of what was needed. It turns out we were not taking the Ethernet
header into account and as a result we were eating into the 8 bytes
reserved for the encap limit.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
ether_setup sets IFF_TX_SKB_SHARING but this is not supported by gre
as it modifies the skb on xmit.
Also, clean up whitespace in ipgre_tap_setup when we're already touching it.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This also fix a potential race into the existing tunnel code, which
could lead to the wrong dst to be permanenty cached:
CPU1: CPU2:
<xmit on ip6_tunnel>
<cache lookup fails>
dst = ip6_route_output(...)
<tunnel params are changed via nl>
dst_cache_reset() // no effect,
// the cache is empty
dst_cache_set() // the wrong dst
// is permanenty stored
// into the cache
With the new dst implementation the above race is not possible
since the first cache lookup after dst_cache_reset will fail due
to the timestamp check
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Suggested-and-acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/geneve.c
Here we had an overlapping change, where in 'net' the extraneous stats
bump was being removed whilst in 'net-next' the final argument to
udp_tunnel6_xmit_skb() was being changed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Parameters were updated only if the kernel was unable to find the tunnel
with the new parameters, ie only if core pamareters were updated (keys,
addr, link, type).
Now it's possible to update ttl, hoplimit, flowinfo and flags.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It looks like many files are including mroute.h unnecessarily, so remove
the include. Most importantly remove it from ipv6.
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently error log messages in ip6gre_err are printed at 'warn'
level. This is different to most other tunnel types which don't
print any messages. These log messages don't provide any information
that couldn't be deduced with networking tools. Also it can be annoying
to have one end of the tunnel go down and have the logs fill with
pointless messages such as "Path to destination invalid or inactive!".
This patch reduces the log level of these messages to 'dbg' level to
bring the visible behaviour into line with other tunnel types.
Signed-off-by: Matt Bennett <matt.bennett@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Problems in the current dst_entry cache in the ip6_tunnel:
1. ip6_tnl_dst_set is racy. There is no lock to protect it:
- One major problem is that the dst refcnt gets messed up. F.e.
the same dst_cache can be released multiple times and then
triggering the infamous dst refcnt < 0 warning message.
- Another issue is the inconsistency between dst_cache and
dst_cookie.
It can be reproduced by adding and removing the ip6gre tunnel
while running a super_netperf TCP_CRR test.
2. ip6_tnl_dst_get does not take the dst refcnt before returning
the dst.
This patch:
1. Create a percpu dst_entry cache in ip6_tnl
2. Use a spinlock to protect the dst_cache operations
3. ip6_tnl_dst_get always takes the dst refcnt before returning
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work to fix the dst_entry refcnt bugs in
ip6_tunnel.
This patch rename:
1. ip6_tnl_dst_check() to ip6_tnl_dst_get() to better
reflect that it will take a dst refcnt in the next patch.
2. ip6_tnl_dst_store() to ip6_tnl_dst_set() to have a more
conventional name matching with ip6_tnl_dst_get().
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is a prep work to fix the dst_entry refcnt bugs in ip6_tunnel.
This patch refactors some common init codes used by both
ip6gre_tunnel_init and ip6gre_tap_init.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a tunnel is deleted, the cached dst entry should be released.
This problem may prevent the removal of a netns (seen with a x-netns IPv6
gre tunnel):
unregister_netdevice: waiting for lo to become free. Usage count = 3
CC: Dmitry Kozlov <xeb@mail.ru>
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the meaning of net.ipv6.auto_flowlabels to provide a mode for
automatic flow labels generation. There are four modes:
0: flow labels are disabled
1: flow labels are enabled, sockets can opt-out
2: flow labels are allowed, sockets can opt-in
3: flow labels are enabled and enforced, no opt-out for sockets
np->autoflowlabel is initialized according to the sysctl value.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can't call skb_get_hash here since the packet is not complete to do
flow_dissector. Create hash based on flowi6 instead.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code there just open-codes the same, so use the provided macro instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Don't use dev->iflink anymore.
CC: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Those are counterparts to nla_put_in_addr and nla_put_in6_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP addresses are often stored in netlink attributes. Add generic functions
to do that.
For nla_put_in_addr, it would be nicer to pass struct in_addr but this is
not used universally throughout the kernel, in way too many places __be32 is
used to store IPv4 address.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x != NULL and sometimes as x. x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 code uses a mixture of coding styles. In some instances check for NULL
pointer is done as x == NULL and sometimes as !x. !x is preferred according to
checkpatch and this patch makes the code consistent by adopting the latter
form.
No changes detected by objdiff.
Signed-off-by: Ian Morris <ipm@chirality.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
info is in network byte order, change it back to host byte order
before use. In particular, the current code sets the MTU of the tunnel
to a wrong (too big) value.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using GRE redirection in WCCP, it sets the wrong skb->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Cc: Dmitry Kozlov <xeb@mail.ru>
Signed-off-by: Yuri Chislov <yuri.chislov@gmail.com>
Tested-by: Yuri Chislov <yuri.chislov@gmail.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we need the IP6_TNL_F_CAP_XMIT capabiltiy to transmit
packets through an ipv6 tunnel. This capability is set when the
tunnel gets configured, based on the tunnel endpoint addresses.
On tunnels with wildcard tunnel endpoints, we need to do the
capabiltiy checking on a per packet basis like it is done in
the receive path.
This patch extends ip6_tnl_xmit_ctl() to take local and remote
addresses as parameters to allow for per packet capabiltiy
checking.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it gets overwritten by register_netdev().
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Shweta Choudaha