Reduce size of duplicated comments by switching to use SPDX identifier.
No functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix few indentation splats. No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amend comments in the code:
- adding periods to the multi-line comments
- fixing typos
- capitalize first word in the sentences
- etc
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to include linux/init.h when at the same time
we include linux/module.h.
Remove redundant inclusion.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug prints of network operations will look better if network
device name is printed. The benefit of that is a possibility to distinguish
the actual hardware when more than one is installed on the system.
Convert appropriate printk(KERN_DEBUG) to netdev_print(KERN_DEBUG, ndev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debug prints of hardware status and operations will look better
if SPI device name is printed. The benefit of that is a possibility
to distinguish the actual hardware when more than one is installed
on the system.
Convert appropriate printk(KERN_DEBUG) to dev_print(KERN_DEBUG, &spi->dev).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using open coded printk(KERN_<LEVEL>) switch the driver to use
dev_<level> macros.
Note, the device name will be printed in full, which is beneficial when
more than one card installed on the system.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ether_addr_copy() instead of memcpy() to copy the mac address.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate some boilerplate code by using module_spi_driver() instead of
->init() / ->exit(), moving the salient bits from ->init() into ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When dev_<level>() macros are used against SPI device, the driver's name
is printed as well. No need to duplicate this explicitly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace open coded netdev_<level>() macros.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ->probe() and ->remove() stages can be easily debugged with
initcall_debug or function tracer. There is no need to repeat the same
explicitly in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the DT-specific of_get_mac_address() function with
device_get_mac_address, which works on both DT and ACPI platforms.
This change makes it easier to add ACPI support.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netif_msg_init() API takes on input the amount of bits to be set. The
description of debug parameter in the enc28j60 module is misleading in this
sense and passing 0xffff does not give an expected behaviour.
Fix the description of debug module parameter to show what exactly is expected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With centralized MTU checking, there's nothing productive done by
eth_change_mtu that isn't already done in dev_set_mtu, so mark it as
deprecated and remove all usage of it in the kernel. All callers have been
audited for calls to alloc_etherdev* or ether_setup directly, which means
they all have a valid dev->min_mtu and dev->max_mtu. Now eth_change_mtu
prints out a netdev_warn about being deprecated, for the benefit of
out-of-tree drivers that might be utilizing it.
Of note, dvb_net.c actually had dev->mtu = 4096, while using
eth_change_mtu, meaning that if you ever tried changing it's mtu, you
couldn't set it above 1500 anymore. It's now getting dev->max_mtu also set
to 4096 to remedy that.
v2: fix up lantiq_etop, missed breakage due to drive not compiling on x86
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupt worker code for the enc28j60 relies only on the TXIF flag to
determinate if the packet transmission was completed. However the datasheet
specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
transmit abort. Also in section 12.1.4 that TXIF will be set
when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
during transmission errors.
This causes a race condition, since the worker code will invoke
enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
called, the worker from the interrupt handler will enter the path for error
handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
and releasing the packet scheduled for transmission, causing a kernel crash with
due a NULL pointer.
These crashes due a NULL pointer were observed under stress conditions of the
device. A BUG_ON() sequence was used to validate the issue was fixed, and has
been running without problems for 2 years now.
Signed-off-by: Diego Dompe <dompe@hpe.com>
Acked-by: Sergio Valverde <sergio.valverde@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch adds the required match table for device tree support
(and while at, fix the indent). It's also possible to specify the
MAC address in the DT blob.
Also add the corresponding binding documentation file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current spi_read_buf function fails on SPI host masters which
are only half-duplex capable. Splitting the Tx and Rx part solves
this issue.
Tested on Raspberry Pi (full duplex) and I2SE Duckbill (half duplex).
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
An spi_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use eth_hw_addr_random() instead of calling random_ether_addr()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Reset the state to NET_ADDR_PERM as soon as the MAC get
changed via .ndo_set_mac_address.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet
- Removed extra skb->dev = dev after netdev_alloc_skb
Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the Microchip driver into drivers/net/ethernet/microchip/ and
make the necessary Kconfig and Makefile changes.
CC: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Michael S. Tsirkin