Overloading dev->s_filter to do two different functions (set wakeup filters
and generic hardware filters) makes it impossible to tell what the
hardware actually supports, so create a separate dev->s_wakeup_filter and
make the distinction explicit.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This reverts 18bc174481 and changes
the code at img-ir-nec.c to use the order used by the other NEC decoders.
The original patch ignored the fact that NEC32 scancodes are generated not
only in the NEC raw decoder but also directly in some drivers. Whichever
approach is chosen it should be consistent across drivers and this patch
needs more discussion.
Furthermore, I'm convinced that we have to stop playing games trying to
decipher the "meaning" of NEC scancodes (what's the customer/vendor/address,
which byte is the MSB, etc).
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The calculated values for the minlen and maxlen fields, which were
rounded to multiples of 2 and clamped to a valid range, were left
unused. Use them in the calculation of the register value rather than
using the raw input minlen and maxlen.
This fixes the following warning with a W=1 build:
drivers/media/rc/img-ir/img-ir-hw.c In function ‘img_ir_free_timing’:
drivers/media/rc/img-ir/img-ir-hw.c +228 :23: warning: variable ‘maxlen’ set but not used [-Wunused-but-set-variable]
drivers/media/rc/img-ir/img-ir-hw.c +228 :15: warning: variable ‘minlen’ set but not used [-Wunused-but-set-variable]
Reported-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The JVC timings included timings intended for the secondary decoder
(which matches messages with no leader), however they were in the wrong
part of the timings structure, repeating s00 and s01 rather than being
in s10 and s11.
Distinct repeat timings can't be properly supported yet for JVC anyway
since the scancode callback cannot determine which decoder matched the
message, so for now remove these timings and don't bother to enable the
secondary decoder.
This fixes the following warnings with W=1:
drivers/media/rc/img-ir/img-ir-jvc.c +76 :3: warning: initialized field overwritten [-Woverride-init]
drivers/media/rc/img-ir/img-ir-jvc.c +76 :3: warning: (near initialization for ‘img_ir_jvc.timings.s00’) [-Woverride-init]
drivers/media/rc/img-ir/img-ir-jvc.c +81 :3: warning: initialized field overwritten [-Woverride-init]
drivers/media/rc/img-ir/img-ir-jvc.c +81 :3: warning: (near initialization for ‘img_ir_jvc.timings.s01’) [-Woverride-init]
Reported-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the Sanyo infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the Sharp infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the Sony infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the JVC infrared protocol.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add an img-ir module for decoding the NEC and extended NEC infrared
protocols.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add ImgTec IR decoder driver to the build system.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add remote control input driver for the ImgTec Infrared block hardware
decoder, which is set up with timings for a specific protocol and
supports mask/value filtering and wake events.
The hardware decoder timing values, raw data to scan code conversion
function and scan code filter to raw data filter conversion function
will be provided in separate files for each protocol which this part of
the driver can use. The new generic scan code filter interface is made
use of to reduce interrupts and control wake events.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add raw IR remote control input driver for the ImgTec Infrared decoder
block's raw edge interrupts. Generic software protocol decoders are used
to allow multiple protocols to be supported at a time, including those
not supported by the hardware decoder.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add base driver for the ImgTec Infrared decoder block. The driver is
split into separate components for raw (software) decode and hardware
decoder which are in following commits.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
David Härdeman