Other drivers duplicate this code; no sense in having it be private
to psmouse-base.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Several protocol initialization routines can fail after they set up
psmouse methods, such as reconnect and disconnect. This may lead to
these stale methods used with different protocol that they were
intended to be used for and may cause unpredictavle behavior and/or
crashes.
Make sure we start with a clean slate before executing each and every
protocol detection and/or initialization routine.
Reported-by: Paul Fox <pgf@laptop.org>
Acked-by: Tai-hwa Liang <avatar@sentelic.com>
Acked-by: Paul Fox <pgf@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently, the synaptics driver puts the device into Absolute mode.
As explained in the synaptics documentation section 3.2, in this mode,
the device sends a continuous stream of packets at the maximum rate
to the host when the user's fingers are near or on the pad or
pressing buttons, and continues streaming for 1 second afterwards.
These packets are even sent when there is no new information to report,
even when they are duplicates of the previous packet.
For embedded systems this is a bit much - it results in a huge
and uninterrupted stream of interrupts at high rate.
This patch adds support for Relative mode, which can be selected as
a new psmouse protocol. In this mode, the device does not send duplicate
packets and acts like a standard PS/2 mouse. However, synaptics-specific
functionality is still available, such as the ability to set the packet
rate, and rather than disabling gestures and taps at the hardware level
unconditionally, a 'synaptics_disable_gesture' sysfs attribute has
been added to allow control of this functionality.
This solves a long standing OLPC issue: synaptics hardware enables
tap to click by default (even in the default relative mode), but we
have found this to be inappropriate for young children and first
time computer users. Enabling the synaptics driver disables tap-to-click,
but we have previously been unable to use this because it also enables
Absolute mode, which is too "spammy" for our desires and actually
overloads our EC with its continuous stream of packets. Now we can enable
the synaptics driver, disabling tap to click while retaining the less
noisy Relative mode.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
With commit 67d0a07544 we mark strict_strtox
as obsolete. Convert all remaining such uses in drivers/input/.
Also change long to appropriate types, and return error conditions
from kstrtox separately, as Dmitry sugguests.
Signed-off-by: JJ Ding <dgdunix@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This will ensure our reporting is consistent with the rest of the system
and we do not refer to obsolete source file names.
Reviewed-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Reviewed-by: JJ Ding <dgdunix@gmail.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a "hgpk_mode" sysfs attribute that allows selection between 3 options:
Mouse (the existing option), GlideSensor and PenTablet.
GlideSensor is an enhanced protocol for the regular touchpad mode that
additionally reports pressure and uses absolute coordinates. We suspect
that it may be more reliable than mouse mode in some environments.
PenTablet mode puts the touchpad into resistive mode, you must then use
a stylus as an input. We suspect this is the most reliable way to drive
the touchpad.
The GlideSensor and PenTablet devices expose themselves with the
intention of being combined with the synaptics X11 input driver.
Based on earlier work by Paul Fox.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some (rare) serio devices need to have multiple serio children. One of
the examples is PS/2 multiplexer present on several TQC STKxxx boards,
which connect PS/2 keyboard and mouse to single tty port.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is more kernel-ish, saves some space, and also allows us to
expand the ops without breaking all the callers who are happy for the
new members to be NULL.
The few places which defined their own param types are changed to the
new scheme (more which crept in recently fixed in following patches).
Since we're touching them anyway, we change get() and set() to take a
const struct kernel_param (which they really are). This causes some
harmless warnings until we fix them (in following patches).
To reduce churn, module_param_call creates the ops struct so the callers
don't have to change (and casts the functions to reduce warnings).
The modern version which takes an ops struct is called module_param_cb.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Phil Carmody <ext-phil.2.carmody@nokia.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Ville Syrjala <syrjala@sci.fi>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Alessandro Rubini <rubini@ipvvis.unipv.it>
Cc: Michal Januszewski <spock@gentoo.org>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-kernel@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: linux-fbdev-devel@lists.sourceforge.net
Cc: linux-nfs@vger.kernel.org
Cc: netdev@vger.kernel.org
Synaptics hardware requires resetting device after suspend to ram
in order for the device to be operational. The reset lives in
synaptics-specific reconnect handler, but it is not being invoked
if synaptics support is disabled and the device is handled as a
standard PS/2 device (bare or IntelliMouse protocol).
Let's add reset into generic reconnect handler as well.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Observing behavior of the other OS it appears that parity errors reported
by the keyboard controller are being ignored and the data is processed
as usual. Let's do the same for standard PS/2 protocols (bare, Intellimouse
and Intellimouse Explorer) to provide better compatibility. Thsi should fix
teh following bug:
https://bugzilla.kernel.org/show_bug.cgi?id=6105
Thanks for Damjan Jovanovic for locating the source of issue and ideas
for the patch.
Tested-by: Damjan Jovanovic <damjan.jov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Set state of the device as "initializing" during and after cleanup
to ensure that unsolicited data from the device is not passed on.
We especially want to avoid processing new device announcements
"0xaa 0x00" that can come up before we perform reconnect operation.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sentelic probes confuse IBM trackpoints so they stop responding to
TP_READ_ID command. See:
http://bugzilla.kernel.org/show_bug.cgi?id=14970
Let's move FSP detection lower so it is probed after trackpoint and
others, just before we strat probing for Intellimouse Explorer.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
For configurations where Synaptics hardware is present but the Synaptics
extensions support is not compiled in, the mouse is reprobed and a new
device is allocated on every suspend/resume.
During probe, psmouse_switch_protocol() calls psmouse_extensions() with
set_properties=1. This calls the dummy synaptics_init() which returns an
error code, instructing us not to use the synaptics extensions.
During resume, psmouse_reconnect() calls psmouse_extensions() with
set_properties=0, in which case call to synaptics_init() is bypassed and
PSMOUSE_SYNAPTICS is returned. Since the result is different from previous
attempt psmouse_reconnect() fails and full re-probe happens.
Fix this by tweaking the set_properties=0 codepath in psmouse_extensions()
to be more careful about offering PSMOUSE_SYNAPTICS extensions.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
sysfs_remove_group() waits for sysfs attributes to be removed, therefore
we do not need to worry about driver-specific attributes being accessed
after driver has been detached from the device. In fact, attempts to take
serio->drv_mutex in attribute methods may lead to the following deadlock:
sysfs_read_file()
fill_read_buffer()
sysfs_get_active_two()
psmouse_attr_show_helper()
serio_pin_driver()
serio_disconnect_driver()
mutex_lock(&serio->drv_mutex);
<--------> mutex_lock(&serio_drv_mutex);
psmouse_disconnect()
sysfs_remove_group(... psmouse_attr_group);
....
sysfs_deactivate();
wait_for_completion();
Fix this by removing calls to serio_[un]pin_driver() and functions themselves
and using driver-private mutexes to serialize access to attribute's set()
methods that may change device state.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Instead of doing full-blown reset while suspending or shutting down
the box use lighter form of reset that should take less time.
Tested-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
DMI tables use considerable amount of memory. Mark them as __initconst
so they will be discarded once module is loaded.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Do not start protocol detection assuming that middle mouse is present,
instead let individual protocols explicitly set this capability.
This fixes issue with Synaptics touchpads pretending that they have
middle button when hardware clearly reports otherwise.
Reported-and-tested-by: Andrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b7802c5c1e ("Input: psmouse - use boolean type") caused the
synaptics_hardware variable to be completely useless, as it is
constantly set to 'true' throughout the whole psmouse_extensions().
This was caused by the following hunk in the commit in question
- int synaptics_hardware = 0;
+ bool synaptics_hardware = true;
which is wrong and causes driver to issue extra reset when falling
back to bare PS/2 protocol.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is the driver for Sentelic Finger Sensing Pad which can be found
on MSI WIND Netbook.
Signed-off-by: Tai-hwa Liang <avatar@sentelic.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It appears that when the XO touchpad unit resets from ESD, it sends AA
AA instead of AA 00, the psmouse-base code handles the case of AA 00 by
triggering a serio reconnect for the port, causing a full reprobe of
the device.
Testing with OFW shows that this is likely to solve the problem, so
the attached patch simply expands the existing test to also catch AA AA.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is version 5 of the driver. Relative mode support has been
dropped (users wishing to use touchpad in relative mode can use
standard PS/2 protocol emulation done in hardware). The driver
supports both original version of Elantech protocol and the newer
one used by touchpads installed in EeePC.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This adds support for OLPC's touchpad. It has lots of neat features,
none of which are enabled because the hardware is too buggy. Instead,
we use it like a normal touchpad, but with a number of workarounds in
place to deal with the frequent hardware spasms. Humidity changes,
sweat, tinfoil underwear, plugging in AC, drinks, evil felines.. All
tend to cause the touchpad to freak out.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We want to support attr->set callbacks that may need psmouse->state to
not be updated, or may want to manually deal w/ enabling and disabling
the device. To do that, we create __PSMOUSE_DEFINE_ATTR which enables
us to set a 'protect' argument specifying whether or not the set
callback should be protected with psmouse_disable and state setting.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
psmouse_queue_work is passed a delayed_work struct, and queues up the work
with kpsmouse_wq. Since we're dealing with delayed_work stuff, this
also switches resync_work to a delayed_work struct as well, and makes
use of psmouse_queue_work when doing a resync within psmouse-base.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
strict_strtoul() allows newline character at the end of the the input
string and therefore is more user-friendly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Drop #include <linux/moduleparam.h> in files that also include
linux/module.h, since module.h includes moduleparam.h already.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If we successfully call input_register_device() in psmouse_connect()
but sysfs_create_group() fails, we'll enter the error path without
ever having called input_unregister_device() potentially leaking
memory.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
get rid of input BIT* duplicate defines
use newly global defined macros for input layer. Also remove includes of
input.h from non-input sources only for BIT macro definiton. Define the
macro temporarily in local manner, all those local definitons will be
removed further in this patchset (to not break bisecting).
BIT macro will be globally defined (1<<x)
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: <dtor@mail.ru>
Acked-by: Jiri Kosina <jkosina@suse.cz>
Cc: <lenb@kernel.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: <perex@suse.cz>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: <vernux@us.ibm.com>
Cc: <malattia@linux.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some rodents appear to be extra-finicky, and require both PSMOUSE_RESET_DIS
and PSMOUSE_RESET_BAT before they are unconfused enough to be probed.
Signed-off-by: Alon Ziv <lkml@nolaviz.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Cortron PS/2 Trackballs (700-0001A) report the 4th button using the 4th
bit of the first packet (yes, it breaks the standard PS/2 protocol).
This patch adds an extra protocol to generate BTN_SIDE based on the 4th
bit. There's no way to detect those trackballs using any kind of special
sequence, thus the protocol must be activated explicitely by writing
into 'protocol' sysfs attribute:
echo -n "cortps" > /sys/devices/platform/i8042/serio1/protocol
Signed-off-by: Aristeu Rozanski <arozansk@redhat.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In preparation for struct class_device -> struct device input
core conversion, switch to using input_dev->dev.parent when
specifying device position in sysfs tree.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Allow ALPS, LOGIPS2PP, LIFEBOOK, TRACKPOINT and TOUCHKIT protocol
extensions of psmouse to be disabled during compilation. This will
allow users save some memory when they are sure that they will only
use a certain type of mice.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Forcing stream mode after reset confuses some devices (reported
by Andrea Arcangeli) so let's take it out - spec says that after
reset mouse should already be in stream mode.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Based on the touchkit USB and lifebook PS/2 touchscreen driver.
The egalax touchsreen controller (PS/2 or USB version) is used in this 7"
device: http://www.cartft.com/catalog/il/449
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some people report that they need psmouse module unloaded
for suspend to ram/disk to work properly. Let's make port
cleanup behave the same way as driver unload.
This fixes "bad state" roblem on various HP laptops, such
as nx7400.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
psmouse_show_int_attr() and psmouse_set_int_attr() were accessing
unsigned int fields as unsigned long, which gave garbage on x86_64.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Dmitry Torokhov