After the result of the previous conversion is read the chip
automatically starts a new conversion and doesn't accept new i2c
transfers until this conversion is completed which makes the function
return failure.
So add an early return iff the programming of the new address isn't
needed. Note this will not fix the problem in general, but all cases
that are currently used. Once this changes we get the failure back, but
this can be addressed when the need arises.
Fixes: 69548b7c2c ("iio: adc: ltc2497: split protocol independent part in a separate module ")
Reported-by: Meng Li <Meng.Li@windriver.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Denys Zagorui <dzagorui@cisco.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220815091647.1523532-1-dzagorui@cisco.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
-----BEGIN PGP SIGNATURE-----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=fUm6
-----END PGP SIGNATURE-----
Merge tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 6.1
This includes Nuno Sa's work to move the IIO core over to generic firmware
properties rather than having DT specific code paths. Combined with Andy
Shevchenko's long term work on drivers, this leaves IIO in a good state for
handling other firmware types.
New device support
- liteon,ltrf216a
* New driver and dt bindings to support this Light sensor.
- maxim,max11205
* New driver for this 16bit single channel ADC.
- memsensing,msa311
* New driver for this accelerometer. Includes a string helper for read/write.
- richtek,rtq6056
* New driver and dt binding to support this current monitor used to measure
power usage.
- yamaha,yas530
* Support the YAS537 variant (series includes several fixes for other parts
and new driver features).
Staging graduation
- adi,ad7746 CDC. Cleanup conducted against set of roadtest tests using
the posted RFC of that framework.
Features
- core
* Large rework to make all the core IIO code use generic firmware properties.
Includes switching some drivers over as well using newly provided
generic interfaces and allowing removal of DT specific ones.
* Support for gesture event types for single and double tap. Used in
bosch,bma400.
- atmel,at91-sama5d2
* Add support for temperature sensor which uses two muxed inputs to estimate
the temperature.
* Handle trackx bits of EMR register to improve temp sampling accuracy.
* Runtime PM support.
- liteon,ltrf216a
* Add a _raw channel output to allow working around an issue with
differing conversions equations that breaks some user space controls.
- mexelis,mlx90632
* Support regulator control.
- ti,tsc2046
* External reference voltage support.
Clean up and minor fixes
- Tree-wide
* devm_clk_get_enabled() replacements of opencoded equivalent.
* Remaining IIO_DMA_MINALIGN conversions (the staging/iio drivers).
* Various minor warning and similar cleanup such as missing static
markings.
* strlcpy() to strscpy() for cases where return value not checked.
* provide units.h entries for more HZ units and use them in drivers.
- dt-bindings cleanup
* Drop maintainers listss where the email address is bouncing.
* Switch spi devices over to using spi-peripheral.yaml
* Add some missing unevaluatedProperties / additionalProperties: false
entries.
- ABI docs
* Add some missing channel type specific sampling frequency entries.
* Add parameter names for callback parameters.
- MAINTAINERS
* Fix wrong ADI forum links.
- core
* lockdep class per device, to avoid an issue with nest when one IIO
device is the consumer of another.
* White space tweaks.
- asc,dlhl60d
* Use get_unaligned_be24 to avoid some unusual data manipulation and masking.
- atmel,at91-sama5d2
* Fix wrong max value.
* Improve error handling when measuring pressure and touch.
* Add locks to remove races on updating oversampling / sampling freq.
* Add missing calls in suspend and resume path to ensure state is correctly
brought up if buffered capture was in use when suspend happened.
* Error out of write_raw() callback if buffered capture enabled to avoid
unpredictable behavior.
* Handle different versions having different oversampling ratio support and
drop excess error checking.
* Cleanup magic value defines where the name is just the value and hence
hurts readability.
* Use read_avail() callback to provide info on possible oversampling ratios.
* Correctly handle variable bit depth when doing oversampling on different
supported parts. Also handle higher oversampling ratios.
- fsl,imx8qxp
* Don't ignore errors from regulator_get_voltage() so as to avoid some
very surprising scaling.
- invensense,icp10100
* Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS. UNIVERSAL rarely made
sense and is now deprecated. In this driver we just avoid double disabling
in some paths.
- maxim,max1363
* Drop consumer channel map provision by platform data. There have been
better ways of doing this for years and there are no in tree users.
- microchip,mcp3911
* Update status to maintained.
- qcom,spmi-adc5
* Support measurement of LDO output voltage.
- qcom,spmi-adc
* Add missing channel available on SM6125 SoC.
- st,stmpe
* Drop requirement on node name in binding now that driver correctly
doesn't enforce it.
- stx104
* Move to more appropriate addac directory
- ti,am335x
* Document ti,am654-adc compatible already in use in tree.
- ti,hmc5843
* Move dev_pm_ops out of header and use new pm macros to handle export.
- yamaha,yas530
* Minor cleanups.
* tag 'iio-for-6.1a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (142 commits)
iio: pressure: icp10100: Switch from UNIVERSAL to DEFINE_RUNTIME_DEV_PM_OPS().
iio: adc: max1363: Drop provision to provide an IIO channel map via platform data
iio: accel: bma400: Add support for single and double tap events
iio: Add new event type gesture and use direction for single and double tap
iio: Use per-device lockdep class for mlock
iio: adc: add max11205 adc driver
dt-bindings: iio: adc: Add max11205 documentation file
iio: magnetometer: yamaha-yas530: Use dev_err_probe()
iio: magnetometer: yamaha-yas530: Make strings const in chip info
iio: magnetometer: yamaha-yas530: Use pointers as driver data
iio: adc: tsc2046: silent spi_device_id warning
iio: adc: tsc2046: add vref support
dt-bindings: iio: adc: ti,tsc2046: add vref-supply property
iio: light: ltrf216a: Add raw attribute
dt-bindings: iio: Add missing (unevaluated|additional)Properties on child nodes
MAINTAINERS: fix Analog Devices forum links
iio/accel: fix repeated words in comments
dt-bindings: iio: accel: add dt-binding schema for msa311 accel driver
iio: add MEMSensing MSA311 3-axis accelerometer driver
dt-bindings: vendor-prefixes: add MEMSensing Microsystems Co., Ltd.
...
Back in the days of board files, platform data was used to provide
information on the mapping from ADC channel to an analog signal
from another device. We've long since moved to doing this via
device tree. Hence drop the support from the max1363 driver which is
the only driver still providing this.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20220821161058.2207185-1-jic23@kernel.org
Adding support for max11205 16-bit single-channel ultra-low power
delta-sigma adc.
The MAX11205 is compatible with the 2-wire interface and uses
SCLK and RDY/DOUT for serial communications. In this mode, all
controls are implemented by timing the high or low phase of the SCLK.
The 2-wire serial interface only allows for data to be read out through
the RDY/DOUT output.
Datasheet: https://datasheets.maximintegrated.com/en/ds/MAX11205.pdf
Signed-off-by: Ramona Bolboaca <ramona.bolboaca@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220831133021.215625-2-ramona.bolboaca@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add spi_device_id to silent following kernel runtime warning:
"SPI driver tsc2046 has no spi_device_id for ti,tsc2046e-adc".
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220904100203.3614502-3-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If VREF pin is attached, we should use external VREF source instead of
the internal. Otherwise we will get wrong measurements on some of the channel
types.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220904100203.3614502-2-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ad7292 tries to add an devm_action for disabling a regulator at
device detach using devm_add_action_or_reset(). The
devm_add_action_or_reset() does call the release function should adding
action fail. The driver inspects the value returned by
devm_add_action_or_reset() and manually calls regulator_disable() if
adding the action has failed. This leads to double disable and messes
the enable count for regulator.
Do not manually call disable if devm_add_action_or_reset() fails.
Fixes: 506d2e317a ("iio: adc: Add driver support for AD7292")
Signed-off-by: Matti Vaittinen <mazziesaccount@gmail.com>
Tested-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/Yv9O+9sxU7gAv3vM@fedora
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC conversion is actually not rail-to-rail but with a factor 1.5.
Make use of this factor when calculating actual voltage.
Fixes: 3a89b289df ("iio: adc: add support for mcp3911")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220722130726.7627-4-marcus.folkesson@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Go for the right property name that is documented in the bindings.
Fixes: 3a89b289df ("iio: adc: add support for mcp3911")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220722130726.7627-3-marcus.folkesson@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for ADC5_VREF_VADC channel to rev2 ADC5 channel list.
This channel measures the VADC reference LDO output.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Link: https://lore.kernel.org/r/20220818221815.346233-3-robimarko@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The thermal OF code has a new API allowing to migrate the OF
initialization to a simpler approach. The ops are no longer device
tree specific and are the generic ones provided by the core code.
Convert the ops to the thermal_zone_device_ops format and use the new
API to register the thermal zone with these generic ops.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linexp.org>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220804224349.1926752-29-daniel.lezcano@linexp.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The device supports negative values as well.
Fixes: 3a89b289df ("iio: adc: add support for mcp3911")
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220722130726.7627-2-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-9-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-8-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_prepared() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-4-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make use of devm_clk_get_enabled() to replace some code that effectively
open codes this new function.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220808204740.307667-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Given the struct platform_driver has one of it's elements assigned to
point to the of_device_id table, it is never going to be unused.
Drop the marking.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Gene Chen <gene_chen@richtek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220807162121.862894-1-jic23@kernel.org
Make the conversion to firmware agnostic device properties. As part of
the conversion the IIO inkern interface 'of_xlate()' is also converted to
'fwnode_xlate()'. The goal is to completely drop 'of_xlate' and hence OF
dependencies from IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220715122903.332535-14-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the conversion to firmware agnostic device properties. As part of
the conversion the IIO inkern interface 'of_xlate()' is also converted to
'fwnode_xlate()'. The goal is to completely drop 'of_xlate' and hence OF
dependencies from IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220715122903.332535-13-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the conversion to firmware agnostic device properties. As part of
the conversion the IIO inkern interface 'of_xlate()' is also converted to
'fwnode_xlate()'. The goal is to completely drop 'of_xlate' and hence OF
dependencies from IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220715122903.332535-12-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the conversion to firmware agnostic device properties. As part of
the conversion the IIO inkern interface 'of_xlate()' is also converted to
'fwnode_xlate()'. The goal is to completely drop 'of_xlate' and hence OF
dependencies from IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220715122903.332535-11-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the conversion to firmware agnostic device properties. As part of
the conversion the IIO inkern interface 'of_xlate()' is also converted to
'fwnode_xlate()'. The goal is to completely drop 'of_xlate' and hence OF
dependencies from IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220715122903.332535-10-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Make the conversion to firmware agnostic device properties. As part of
the conversion the IIO inkern interface 'of_xlate()' is also converted to
'fwnode_xlate()'. The goal is to completely drop 'of_xlate' and hence OF
dependencies from IIO.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220715122903.332535-9-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move from 'of_xlate()' to 'fwnode_xlate()'. The end goal is to completely
drop OF from the IIO inkernel interface.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220715122903.332535-8-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add runtime PM support by disabling/enabling ADC's peripheral clock.
On simple conversion the ADC's clock is kept enabled just while the
conversion is in progress. This includes also temperature conversion.
For triggered buffers and touch conversions the ADC clock is kept enabled
while the triggered buffers or touch are enabled. Along with it removed
the __maybe_unused on suspend() and resume() ops as the dev_pm_ops
object members are now filled with SYSTEM_SLEEP_PM_OPS().
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-20-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADC on SAMA7G5 has a dedicated channel (channel 31) for measuring
in-SoC temperature. 2 inputs are multiplexed on channel 31, VTEMP and
VBG as follows:
`
| \ +-----+
VBG --->| | ch31 | |
Vtemp --->| |----->| ADC |
| / | |
| / +-----+
.
where:
- VTEMP is proportional to the absolute temperature voltage
- VBG is a quasi-temperature independent voltage
Both VBG and VTEMP are needed to determine the correct in-SoC
temperature. At a moment of time only one of these could be measured, the
selection being done with bit SRCLCH bit of ACR register. The formula to
calculate the temperature is as follows:
P1 + (Vref * (VTEMP - P6 - P4 * VBG)) / (VBG * VTEMP_DT)
where:
- P1, P4, P6 are calibration data retrieved from OTP memory
- Vref is the reference voltage for ADC
- VTEMP_DT is the voltage sensitivity to temperature and is constant
- VTEMP, VBG are the measured values from channel 31
For better resolution before reading the temperature certain settings
for oversampling ratio, sample frequency, EMR.TRACKX, MR.TRACKTIM are
applied. The initial settings are reapplied at the end of temperature
reading.
Current support is not integrated with trigger buffers channel 31 not
being enabled/disabled in functions at91_adc_buffer_prepare(),
at91_adc_buffer_postdisable() thus the conversion for channel 31 is not
done in case trigger buffers are enabled. In case of trigger buffers are
enabled and temperature requests are received in the driver though
at91_adc_read_temp() the at91_adc_read_temp() will return with an error
code.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-18-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove iio_device_{claim, release}_direct_mode() and lock/unlock to
&st->lock from at91_adc_read_info_raw(). Instead add a wrapper around
at91_adc_read_info_raw() and do there the lock/unlock. This will allow
using the at91_adc_read_info_raw() in patch that add support for
temperature sensor.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-16-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add startup and tracktim as parameter for at91_adc_setup_samp_freq()
function. In case of temperature sensor being enabled these parameters
will be configured on temperature read request to improve the accuracy
of the read temperature.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-15-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for updating trackx bits of EMR register. Having different
values of EMR.TRACKX when measuring temperature give a better accuracy.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-14-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC captures data on 12 bits (if oversampling is not enabled). When using
oversampling captured data could go up to 14 bits for SAMA5D2 or up to
16 bits for SAMA7G5 (depending on oversampling settings). All the channels
that are subject of oversampling are registered as 14 or 16 real bits.
Depending on the oversampling settings the ADC converted value need to be
shifted up to 14 or 16 to cope with realbits value registered to IIO
subsystem. Commit adds platform specific information to know if we
run on a system with up to 14 or 16 bits ADC converted data.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-11-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add .read_avail() to chan_info ops which will retrieve the available
oversampling ratio.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-10-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Drop AT91_OSR_1SAMPLES, AT91_OSR_4SAMPLES, AT91_OSR_16SAMPLES defines
and insted use their values inline.
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-9-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Oversampling values are checked anyway in at91_adc_emr_config(). Remove
the checking of these from at91_adc_write_raw() and return -EINVAL
instead in at91_adc_emr_config().
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-8-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
SAMA7G5 introduces 64 and 256 oversampling rates. Due to this EMR.OSR is 3
bits long. Change the code to reflect this. Commit prepares the code
for the addition of 64 and 256 oversampling rates.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-7-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When buffers are enabled conversion may start asynchronously thus
allowing changes on actual hardware could lead to bad behavior. Thus
do not allow changing oversampling ratio and sample frequency when
if iio_device_claim_direct_mode() returns with error.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-6-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In case triggered buffers are enabled while system is suspended they will
not work anymore after resume. For this call at91_adc_buffer_postdisable()
on suspend and at91_adc_buffer_prepare() on resume. On tests it has been
seen that at91_adc_buffer_postdisable() call is not necessary but it has
been kept because it also does the book keeping for DMA. On resume path
there is no need to call at91_adc_configure_touch() as it is embedded in
at91_adc_buffer_prepare().
Fixes: 073c662017 ("iio: adc: at91-sama5d2_adc: add support for DMA")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-5-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
.read_raw()/.write_raw() could be called asynchronously from user space
or other in kernel drivers. Without locking on st->lock these could be
called asynchronously while there is a conversion in progress. Read will
be harmless but changing registers while conversion is in progress may
lead to inconsistent results. Thus, to avoid this lock st->lock.
Fixes: 27e1771908 ("iio:adc:at91_adc8xx: introduce new atmel adc driver")
Fixes: 6794e23fa3 ("iio: adc: at91-sama5d2_adc: add support for oversampling resolution")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-4-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Check return status of at91_adc_read_position() and
at91_adc_read_pressure() in at91_adc_read_info_raw().
Fixes: 6794e23fa3 ("iio: adc: at91-sama5d2_adc: add support for oversampling resolution")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-3-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All ADC HW versions handled by this driver (SAMA5D2, SAM9X60, SAMA7G5)
have MR.TRACKTIM on 4 bits. Fix AT91_SAMA5D2_MR_TRACKTIM_MAX to reflect
this.
Fixes: 27e1771908 ("iio:adc:at91_adc8xx: introduce new atmel adc driver")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220803102855.2191070-2-claudiu.beznea@microchip.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add Richtek rtq6056 supporting.
It can be used for the system to monitor load current and power with 16-bit
resolution.
Signed-off-by: ChiYuan Huang <cy_huang@richtek.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/1658242365-27797-3-git-send-email-u0084500@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If the ADC vref regulator returns an error, for example, if CONFIG_REGULATOR
is not set, the error will be used as a reference voltage.
Introduce a guard for negative return values instead of unconditionally
casting it to u32.
Acked-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Martin Larsson <martin.larsson@actia.se>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20220720153136.3502440-1-martin.larsson@actia.se
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If max1027_wait_eoc() fails then call iio_device_release_direct_mode()
before returning.
Fixes: a0e831653e ("iio: adc: max1027: Introduce an end of conversion helper")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YsbztVuAXnau2cIZ@kili
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switching to these newer macros allows the compiler to remove
the unused functions and struct dev_pm_ops if !CONFIG_PM without
the need to mark anything __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Cai Huoqing <cai.huoqing@linux.dev>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-28-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-10-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-9-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused. This one is a little unusual as
no suspend callback, but the cleanup is still worthwhile (and eventual
aim is to get rid of old macro).
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-8-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: Hui Liu <hui.liu@mediatek.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-7-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-6-jic23@kernel.org
In this case we only gain the ability to have the compiler drop the
struct dev_pm_ops because the callbacks are called from paths other
than suspend and resume. In general the purpose of this new macro
is to allow automated removal of the callbacks as well, but that doesn't
apply here.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-5-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-4-jic23@kernel.org
Using these newer macros allows the compiler to remove the unused
structure and functions when !CONFIG_PM_SLEEP + removes the need to
mark pm functions __maybe_unused.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220621202719.13644-3-jic23@kernel.org
Adding ADC NPCM8XX support to NPCM ADC driver.
ADC NPCM8XX uses a different resolution and voltage reference.
As part of adding NPCM8XX support:
- Add NPCM8XX specific compatible string.
- Add data to handle architecture-specific ADC parameters.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Link: https://lore.kernel.org/r/20220713132640.215916-3-tmaimon77@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Several on-running cleanup efforts dominate this time, plus the DMA
safety alignment issue identified due to improved understanding of
the restrictions as a result of Catalin Marinas' efforts in that area.
One immutable branch in here due to MFD and SPMI elements needed for
the qcom-rradc driver.
Device support
* bmi088
- Add support for bmi085 (accelerometer part of IMU)
- Add support for bmi090l (accelerometer part of IMU)
* mcp4922
- Add support for single channel device MCP4921
* rzg2l-adc
- Add compatible and minor tweaks to support RZ/G2UL ADC
* sca3300
- Add support for scl3300 including refactoring driver to support
multiple device types and cleanup noticed whilst working on driver.
* spmi-rradc
- New driver for Qualcomm SPMI Round Robin ADC including necessary
additional utility functions in SPMI core and related MFD driver.
* ti-dac55781
- Add compatible for DAC121C081 which is very similar to existing parts.
Features
* core
- Warn on iio_trigger_get() on an unregistered IIO trigger.
* bma400
- Triggered buffer support
- Activity and step counting
- Misc driver improvements such as devm and header ordering
* cm32181
- Add PM support.
* cros_ec
- Sensor location support
* sx9324
- Add precharge resistor setting
- Add internal compensation resistor setting
- Add CS idle/sleep mode.
* sx9360
- Add precharge resistor setting
* vl53l0x
- Handle reset GPIO, regulator and relax handling of irq type.
Cleanup and minor fixes:
Treewide changes
- Cleanup of error handling in remove functions in many drivers.
- Update dt-binding maintainers for a number of ADI bindings.
- Several sets of conversion of drivers from device tree specific to
generic device properties. Includes fixing up various related
header and Kconfig issues.
- Drop include of of.h from iio.h and fix up drivers that need to include
it directly.
- More moves of clusters of drivers into appropriate IIO_XXX namespaces.
- Tree wide fix of a long running bug around DMA safety requirements.
IIO was using __cacheline_aligned to pad iio_priv() structures. This
worked for a long time by coincidence, but correct alignment is
ARCH_KMALLOC_MINALIGN. As there is activity around this area, introduce
an IIO local IIO_DMA_MINALIGN to allow for changing it in one place rather
than every driver in future. Note, there have been no reports of this
bug in the wild, and it may not happen on any platforms supported by
upstream, so no rush to backport these fixes.
Other cleanup
* core
- Switch to ida_alloc()/free()
- Drop unused iio_get_time_res()
- Octal permissions and DEVICE_ATTR_* macros.
- Cleanup bared unsigned usage.
* MAINTAINERS
- Add include/dt-bindings/iio/ to the main IIO entry.
* ad5380
- Comment syntax fix.
* ad74413r
- Call to for_each_set_bit_from(), with from value as 0 replaced.
* ad7768-1
- Drop explicit setting of INDIO_BUFFER_TRIGGERED as now done by the core.
* adxl345
- Fix wrong address in dt-binding example.
* adxl367
- Drop extra update of FIFO watermark.
* at91-sama5d2
- Limit requested watermark to the hwfifo size.
* bmg160, bme680
- Typos
* cio-dac
- Switch to iomap rather than direct use of ioports
* kxsd9
- Replace CONFIG_PM guards with new PM macros that let the compiler
cleanly remove the unused code and structures when !CONFIG_PM
* lsm6dsx
- Use new pm_sleep_ptr() and EXPORT_SIMPLE_DEV_PM_OPS(). Then move
to Namespace.
* meson_saradc - general cleanup.
- Avoid attaching resources to iio_dev->dev
- Use same struct device for all error messages
- Convert to dev_err_probe() and use local struct device *dev to
reduce code complexity.
- Use devm_clk_get_optional() instead of hand rolling.
- Use regmap_read_poll_timeout() instead of hand rolling.
* mma7660
- Drop ACPI_PTR() use that is unhelpful.
* mpu3050
- Stop exporting symbols not used outside of module
- Switch to new DEFINE_RUNTIME_DEV_PM_OPS() macro and move to Namespace.
* ping
- Typo fix
* qcom-spmi-rradc
- Typo fix
* sc27xx
- Convert to generic struct u32_fract
* srf08
- Drop a redundant check on !val
* st_lsm6dsx
- Limit the requested watermark to the hwfifo size.
* stm32-adc
- Use generic_handle_domain_irq() instead of opencoding.
- Fix handling of ADC disable.
* stm32-dac
- Use str_enabled_disable() instead of open coding.
* stx104
- Switch to iomap rather than direct use of ioports
* tsc2046
- Drop explicit setting of INDIO_BUFFER_TRIGGERED as now done by the core.
* tsl2563
- Replace flush_scheduled_work() with cancel_delayed_work_sync()
- Replace cancel_delayed_work() with cancel_delayed_work_sync()
* vl53l0x
- Make the VDD regulator optional by allowing a dummy regulator.
-----BEGIN PGP SIGNATURE-----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=IcsE
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.20a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
IIO new device support, features and minor fixes for 5.20
Several on-running cleanup efforts dominate this time, plus the DMA
safety alignment issue identified due to improved understanding of
the restrictions as a result of Catalin Marinas' efforts in that area.
One immutable branch in here due to MFD and SPMI elements needed for
the qcom-rradc driver.
Device support
* bmi088
- Add support for bmi085 (accelerometer part of IMU)
- Add support for bmi090l (accelerometer part of IMU)
* mcp4922
- Add support for single channel device MCP4921
* rzg2l-adc
- Add compatible and minor tweaks to support RZ/G2UL ADC
* sca3300
- Add support for scl3300 including refactoring driver to support
multiple device types and cleanup noticed whilst working on driver.
* spmi-rradc
- New driver for Qualcomm SPMI Round Robin ADC including necessary
additional utility functions in SPMI core and related MFD driver.
* ti-dac55781
- Add compatible for DAC121C081 which is very similar to existing parts.
Features
* core
- Warn on iio_trigger_get() on an unregistered IIO trigger.
* bma400
- Triggered buffer support
- Activity and step counting
- Misc driver improvements such as devm and header ordering
* cm32181
- Add PM support.
* cros_ec
- Sensor location support
* sx9324
- Add precharge resistor setting
- Add internal compensation resistor setting
- Add CS idle/sleep mode.
* sx9360
- Add precharge resistor setting
* vl53l0x
- Handle reset GPIO, regulator and relax handling of irq type.
Cleanup and minor fixes:
Treewide changes
- Cleanup of error handling in remove functions in many drivers.
- Update dt-binding maintainers for a number of ADI bindings.
- Several sets of conversion of drivers from device tree specific to
generic device properties. Includes fixing up various related
header and Kconfig issues.
- Drop include of of.h from iio.h and fix up drivers that need to include
it directly.
- More moves of clusters of drivers into appropriate IIO_XXX namespaces.
- Tree wide fix of a long running bug around DMA safety requirements.
IIO was using __cacheline_aligned to pad iio_priv() structures. This
worked for a long time by coincidence, but correct alignment is
ARCH_KMALLOC_MINALIGN. As there is activity around this area, introduce
an IIO local IIO_DMA_MINALIGN to allow for changing it in one place rather
than every driver in future. Note, there have been no reports of this
bug in the wild, and it may not happen on any platforms supported by
upstream, so no rush to backport these fixes.
Other cleanup
* core
- Switch to ida_alloc()/free()
- Drop unused iio_get_time_res()
- Octal permissions and DEVICE_ATTR_* macros.
- Cleanup bared unsigned usage.
* MAINTAINERS
- Add include/dt-bindings/iio/ to the main IIO entry.
* ad5380
- Comment syntax fix.
* ad74413r
- Call to for_each_set_bit_from(), with from value as 0 replaced.
* ad7768-1
- Drop explicit setting of INDIO_BUFFER_TRIGGERED as now done by the core.
* adxl345
- Fix wrong address in dt-binding example.
* adxl367
- Drop extra update of FIFO watermark.
* at91-sama5d2
- Limit requested watermark to the hwfifo size.
* bmg160, bme680
- Typos
* cio-dac
- Switch to iomap rather than direct use of ioports
* kxsd9
- Replace CONFIG_PM guards with new PM macros that let the compiler
cleanly remove the unused code and structures when !CONFIG_PM
* lsm6dsx
- Use new pm_sleep_ptr() and EXPORT_SIMPLE_DEV_PM_OPS(). Then move
to Namespace.
* meson_saradc - general cleanup.
- Avoid attaching resources to iio_dev->dev
- Use same struct device for all error messages
- Convert to dev_err_probe() and use local struct device *dev to
reduce code complexity.
- Use devm_clk_get_optional() instead of hand rolling.
- Use regmap_read_poll_timeout() instead of hand rolling.
* mma7660
- Drop ACPI_PTR() use that is unhelpful.
* mpu3050
- Stop exporting symbols not used outside of module
- Switch to new DEFINE_RUNTIME_DEV_PM_OPS() macro and move to Namespace.
* ping
- Typo fix
* qcom-spmi-rradc
- Typo fix
* sc27xx
- Convert to generic struct u32_fract
* srf08
- Drop a redundant check on !val
* st_lsm6dsx
- Limit the requested watermark to the hwfifo size.
* stm32-adc
- Use generic_handle_domain_irq() instead of opencoding.
- Fix handling of ADC disable.
* stm32-dac
- Use str_enabled_disable() instead of open coding.
* stx104
- Switch to iomap rather than direct use of ioports
* tsc2046
- Drop explicit setting of INDIO_BUFFER_TRIGGERED as now done by the core.
* tsl2563
- Replace flush_scheduled_work() with cancel_delayed_work_sync()
- Replace cancel_delayed_work() with cancel_delayed_work_sync()
* vl53l0x
- Make the VDD regulator optional by allowing a dummy regulator.
* tag 'iio-for-5.20a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (244 commits)
iio: adc: xilinx-xadc: Drop duplicate NULL check in xadc_parse_dt()
iio: adc: xilinx-xadc: Make use of device properties
iio: light: cm32181: Add PM support
iio: adc: ad778-1: do not explicity set INDIO_BUFFER_TRIGGERED mode
iio: adc: ti-tsc2046: do not explicity set INDIO_BUFFER_TRIGGERED mode
iio: adc: stm32-adc: disable adc before calibration
iio: adc: stm32-adc: make safe adc disable
iio: dac: ad5380: align '*' each line and drop unneeded blank line
iio: adc: qcom-spmi-rradc: Fix spelling mistake "coherrency" -> "coherency"
iio: Don't use bare "unsigned"
dt-bindings: iio: dac: mcp4922: expand for mcp4921 support
iio: dac: mcp4922: add support to mcp4921
iio: chemical: sps30: Move symbol exports into IIO_SPS30 namespace
iio: pressure: bmp280: Move symbol exports to IIO_BMP280 namespace
iio: imu: bmi160: Move exported symbols to IIO_BMI160 namespace
iio: adc: stm32-adc: Use generic_handle_domain_irq()
proximity: vl53l0x: Make VDD regulator actually optional
MAINTAINERS: add include/dt-bindings/iio to IIO SUBSYSTEM AND DRIVERS
dt-bindings: iio/accel: Fix adi,adxl345/6 example I2C address
iio: gyro: bmg160: Fix typo in comment
...
The fwnode_for_each_child_node() is NULL-aware, no need to check
its parameters outside. Drop duplicate NULL check in xadc_parse_dt().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220531141118.64540-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220531141118.64540-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The core sets INDIO_BUFFER_TRIGGERED as part of
devm_iio_triggered_buffer_setup().
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220629203910.4836-1-marcus.folkesson@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The calibration is launched from prepare callback.
The ADC state when entering this function may be unknown as the
ADC may have been left enabled by boot stage.
One prerequisite for ADC calibration is to have ADC in disabled state.
If the calibration is started when ADC is still enabled, the behavior is
unpredictable, and the calibration may fail with a timeout error.
Force ADC to disabled state in stm32h7_adc_selfcalib().
ADC enabling is ensured by stm32h7_adc_enable() call,
before leaving prepare callback.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220620154738.801706-3-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
From ADC reference manual the software is allowed to write the
control bit ADDIS of the ADC_CR register only if the ADC is enabled.
Return immediately from stm32h7_adc_disable() if ADC is already disabled.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220620154738.801706-2-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Most of these have been in next for a long time. Unfortunately there
was one stray patch in the branch (wasn't a fix), so I've just rebased
to remove that.
* testing
- Fix a missing MODULE_LICENSE() warning by restricting possible build
configs.
* Various drivers
- Fix ordering of iio_get_trigger() being called before
iio_trigger_register()
* adi,admv1014
- Fix dubious x & !y warning.
* adi,axi-adc
- Fix missing of_node_put() in error and normal paths.
* aspeed,adc
- Add missing of_node_put()
* fsl,mma8452
- Fix broken probing from device tree.
- Drop check on return value of i2c write to device to cause reset as
ACK will be missing (device reset before sending it).
* fsl,vf610
- Fix documentation of in_conversion_mode ABI.
* iio-trig-sysfs
- Ensure irq work has finished before freeing the trigger.
* invensense,mpu3050
- Disable regulators in error path.
* invensense,icm42600
- Fix collision of enum value of 0 with error path where 0 is no match.
* renesas,rzg2l_Adc
- Add missing fwnode_handle_put() in error path.
* rescale
- Fix a boolean logic bug for detection of raw + scale affecting an
obscure corner case.
* semtech,sx9324
- Check return value of read of pin_defs
* st,stm32-adc:
- Fix interaction across ADC instances for some supported devices.
- Drop false spurious IRQ messages.
- Fix calibration value handling. If we can't calibrate don't expose the
vref_int channel.
- Fix maximum clock rate for stm32pm15x
* ti,ads131e08
- Add missing fwnode_handle_put() in error paths.
* xilinx,ams
- Fix variable checked for error from platform_get_irq()
* x-powers,axp288
- Overide TS_PIN bias current for boards where it is not correctly
initialized.
* yamaha,yas530
- Fix inverted check on calibration data being all zeros.
-----BEGIN PGP SIGNATURE-----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=AtPS
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.19a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO fixes for the 5.19 cycle.
Most of these have been in next for a long time. Unfortunately there
was one stray patch in the branch (wasn't a fix), so I've just rebased
to remove that.
* testing
- Fix a missing MODULE_LICENSE() warning by restricting possible build
configs.
* Various drivers
- Fix ordering of iio_get_trigger() being called before
iio_trigger_register()
* adi,admv1014
- Fix dubious x & !y warning.
* adi,axi-adc
- Fix missing of_node_put() in error and normal paths.
* aspeed,adc
- Add missing of_node_put()
* fsl,mma8452
- Fix broken probing from device tree.
- Drop check on return value of i2c write to device to cause reset as
ACK will be missing (device reset before sending it).
* fsl,vf610
- Fix documentation of in_conversion_mode ABI.
* iio-trig-sysfs
- Ensure irq work has finished before freeing the trigger.
* invensense,mpu3050
- Disable regulators in error path.
* invensense,icm42600
- Fix collision of enum value of 0 with error path where 0 is no match.
* renesas,rzg2l_Adc
- Add missing fwnode_handle_put() in error path.
* rescale
- Fix a boolean logic bug for detection of raw + scale affecting an
obscure corner case.
* semtech,sx9324
- Check return value of read of pin_defs
* st,stm32-adc:
- Fix interaction across ADC instances for some supported devices.
- Drop false spurious IRQ messages.
- Fix calibration value handling. If we can't calibrate don't expose the
vref_int channel.
- Fix maximum clock rate for stm32pm15x
* ti,ads131e08
- Add missing fwnode_handle_put() in error paths.
* xilinx,ams
- Fix variable checked for error from platform_get_irq()
* x-powers,axp288
- Overide TS_PIN bias current for boards where it is not correctly
initialized.
* yamaha,yas530
- Fix inverted check on calibration data being all zeros.
* tag 'iio-fixes-for-5.19a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (26 commits)
iio:proximity:sx9324: Check ret value of device_property_read_u32_array()
iio: accel: mma8452: ignore the return value of reset operation
iio: adc: stm32: fix maximum clock rate for stm32mp15x
iio: adc: stm32: fix vrefint wrong calibration value handling
iio: imu: inv_icm42600: Fix broken icm42600 (chip id 0 value)
iio: adc: vf610: fix conversion mode sysfs node name
iio: adc: adi-axi-adc: Fix refcount leak in adi_axi_adc_attach_client
iio: test: fix missing MODULE_LICENSE for IIO_RESCALE=m
iio:humidity:hts221: rearrange iio trigger get and register
iio:chemical:ccs811: rearrange iio trigger get and register
iio:accel:mxc4005: rearrange iio trigger get and register
iio:accel:kxcjk-1013: rearrange iio trigger get and register
iio:accel:bma180: rearrange iio trigger get and register
iio: afe: rescale: Fix boolean logic bug
iio: adc: aspeed: Fix refcount leak in aspeed_adc_set_trim_data
iio: adc: stm32: Fix IRQs on STM32F4 by removing custom spurious IRQs message
iio: adc: stm32: Fix ADCs iteration in irq handler
iio: adc: ti-ads131e08: add missing fwnode_handle_put() in ads131e08_alloc_channels()
iio: adc: rzg2l_adc: add missing fwnode_handle_put() in rzg2l_adc_parse_properties()
iio: trigger: sysfs: fix use-after-free on remove
...
If the vrefint calibration is zero, the vrefint channel output value
cannot be computed. Currently, in such case, the raw conversion value
is returned, which is not relevant.
Do not expose the vrefint channel when the output value cannot be
computed, instead.
Fixes: 0e346b2cfa ("iio: adc: stm32-adc: add vrefint calibration support")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220609095856.376961-1-olivier.moysan@foss.st.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
of_parse_phandle() returns a node pointer with refcount
incremented, we should use of_node_put() on it when not need anymore.
Add missing of_node_put() to avoid refcount leak.
Fixes: ef04070692 ("iio: adc: adi-axi-adc: add support for AXI ADC IP core")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220524074517.45268-1-linmq006@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
of_find_node_by_name() returns a node pointer with refcount
incremented, we should use of_node_put() on it when done.
Add missing of_node_put() to avoid refcount leak.
Fixes: d0a4c17b40 ("iio: adc: aspeed: Get and set trimming data.")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220516075206.34580-1-linmq006@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The check for spurious IRQs introduced in 695e2f5c28 assumed that the bits
in the control and status registers are aligned. This is true for the H7 and MP1
version, but not the F4. The interrupt was then never handled on the F4.
Instead of increasing the complexity of the comparison and check each bit specifically,
we remove this check completely and rely on the generic handler for spurious IRQs.
Fixes: 695e2f5c28 ("iio: adc: stm32-adc: fix a regression when using dma and irq")
Signed-off-by: Yannick Brosseau <yannick.brosseau@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220516203939.3498673-3-yannick.brosseau@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The irq handler was only checking the mask for the first ADCs in the case of the
F4 and H7 generation, since it was iterating up to the num_irq value. This patch add
the maximum number of ADC in the common register, which map to the number of entries of
eoc_msk and ovr_msk in stm32_adc_common_regs. This allow the handler to check all ADCs in
that module.
Tested on a STM32F429NIH6.
Fixes: 695e2f5c28 ("iio: adc: stm32-adc: fix a regression when using dma and irq")
Signed-off-by: Yannick Brosseau <yannick.brosseau@gmail.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220516203939.3498673-2-yannick.brosseau@gmail.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
fwnode_handle_put() should be used when terminating
device_for_each_child_node() iteration with break or return to prevent
stale device node references from being left behind.
Fixes: d935eddd27 ("iio: adc: Add driver for Texas Instruments ADS131E0x ADC family")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com>
Link: https://lore.kernel.org/r/20220517033020.2033324-1-zhangjialin11@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
fwnode_handle_put() should be used when terminating
device_for_each_child_node() iteration with break or return to prevent
stale device node references from being left behind.
Fixes: d484c21bac ("iio: adc: Add driver for Renesas RZ/G2L A/D converter")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jialin Zhang <zhangjialin11@huawei.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220517033526.2035735-1-zhangjialin11@huawei.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The call chain
generic_handle_irq(irq_find_mapping(domain, x));
could be replaced with
generic_handle_domain_irq(domain, x);
which looks up the struct irq_desc for the interrupt and handles it with
handle_irq_desc().
This is a slight optimisation given that the driver invokes only one
function and the struct irq_desc is used directly instead being looked
up via irq_to_desc().
Use generic_handle_domain_irq().
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://lore.kernel.org/r/YnuYoQIzJoFIyEJY@linutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The Round Robin ADC is responsible for reading data about the rate of
charge from the USB or DC input ports, it can also read the battery
ID (resistence), skin temperature and the die temperature of the pmic.
It is found on the PMI8998 and PM660 Qualcomm PMICs.
Signed-off-by: Caleb Connolly <caleb.connolly@linaro.org>
Link: https://lore.kernel.org/r/20220429220904.137297-6-caleb.connolly@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Simplify busy wait stages by using regmap_read_poll_timeout().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> # GXM VIM2
Link: https://lore.kernel.org/r/20220603100004.70336-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use temporary variable for struct device to make code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20220603100004.70336-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace open coded variants of devm_clk_get_optional().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20220603100004.70336-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20220603100004.70336-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Align messages to be printed with the physical device prefix as it's done
everywhere else in this driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20220603100004.70336-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
It feels wrong and actually inconsistent to attach managed resources
to the IIO device object, which is child of the physical device object.
The rest of the ->probe() calls do that against physical device.
Resolve this by reassigning managed resources to the physical device object.
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Link: https://lore.kernel.org/r/20220603100004.70336-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of a pair of u32 re-use generic struct u32_fract.
No functional changes intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Cixi Geng <cixi.geng1@unisoc.com>
Link: https://lore.kernel.org/r/20220530180910.2533-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of returning an error if the watermark value is too high, which
the core will silently ignore anyway, limit the value to the hardware
FIFO size; a lower-than-requested value is still better than using the
default, which is usually 1.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220117102512.31725-2-paul@crapouillou.net
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220615120803.41350-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-11-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-10-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-9-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-8-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-7-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-6-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-5-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-4-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-3-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Do not trust the fact that iio.h includes of.h which in turn includes
all the headers we are relying on.
The ultimate goal is to actually drop of.h from iio.h.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220610084545.547700-2-nuno.sa@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: ac2bec9d58 ("iio: adc: tlc4541: add support for TI tlc4541 adc")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-40-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 3e87e78383 ("iio: adc: Add TI ADS8688")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-39-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 8dd2d7c0fe ("iio: adc: Add driver for the TI ADS8344 A/DC chips")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-38-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: 902c4b2446 ("iio: adc: New driver for TI ADS7950 chips")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: David Lechner <david@lechnology.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-37-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: d935eddd27 ("iio: adc: Add driver for Texas Instruments ADS131E0x ADC family")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Tomislav Denis <tomislav.denis@avl.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-36-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: e717f8c6df ("iio: adc: Add the TI ads124s08 ADC code")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-35-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 4d671b71be ("iio: adc: ti-adc161s626: add support for TI 1-channel differential ADCs")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Matt Ranostay <mranostay@gmail.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-34-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 913b864686 ("iio: adc: Add TI ADC128S052")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-33-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 50a6edb1b6 ("iio: adc: add ADC12130/ADC12132/ADC12138 ADC driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-32-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Dual fixes tags as two cases that were introduced in different patches.
One of those patches is a fix however and likely to have been backported
to stable kernels.
Note the second alignment marking is likely to be unnecessary, but is
left for now to keep this fix simple.
Fixes: 3691e5a694 ("iio: adc: add driver for the ti-adc084s021 chip")
Fixes: cbe5c69776 ("iio: adc: ti-adc108s102: Fix alignment of buffer pushed to iio buffers.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-31-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: 3691e5a694 ("iio: adc: add driver for the ti-adc084s021 chip")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Acked-by: Mårten Lindahl <marten.lindahl@axis.com>
Link: https://lore.kernel.org/r/20220508175712.647246-30-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: efc945fb72 ("iio: adc: add support for ADC0831/ADC0832/ADC0834/ADC0838 chips")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-29-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Worth noting the fixes tag refers to the same issue being observed
on a platform that probably had only 64 byte cachelines.
Fixes: 0e81bc99a0 ("iio: mcp320x: Fix occasional incorrect readings")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Michael Welling <mwelling@ieee.org>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-28-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 8a80a71d90 ("iio: adc: Add MAX1241 driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Alexandru Lazar <alazar@startmail.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-27-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: a9e9c7153e ("iio: adc: add max1117/max1118/max1119 ADC driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-26-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: a8e7e88df9 ("iio: adc: Add Maxim MAX11100 driver")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-25-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: fc167f6248 ("iio: add support of the max1027")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-24-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: bc82222fcc ("iio:adc: Driver for Linear Technology LTC2497 ADC")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-23-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes: e4c5c4dfaa ("iio: adc: new driver to support Linear technology's ltc2496")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-22-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 72aa29ce0a ("iio: adc: hi8435: Holt HI-8435 threshold detector")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-21-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Note the fixes tag predates some changes to this line of code so
automated application of this fix may fail.
Fixes: 7f40e06143 ("iio:adc:ad7949: Add AD7949 ADC driver family")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Charles-Antoine Couret <charles-antoine.couret@essensium.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-20-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Note that some other fixes have applied to this line of code
that may complicate automated backporting.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes: 0eac259db2 ("IIO ADC support for AD7923")
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-19-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to include 'may'.
Fixes tag is clearly not where this was introduced but it is very unlikely
anyone will back port it past that point.
Fixes: 65dd3d3d7a ("staging:iio:ad7887: Squash everything into one file")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-18-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to reflect that separate cachelines 'may' be
required.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-17-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to reflect the fact DMA safety 'may' require
separate cachelines.
Fixes: aa16c6bd0e ("iio:adc: Add support for AD7766/AD7767")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-16-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_ALIGN definition.
Update the comment to reflect the fact DMA safety 'may' require
separate cachelines.
Fixes: 7989b4bb23 ("iio: adc: ad7616: Add support for AD7616 ADC")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-15-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to reflect that DMA safety 'may' require separate
cachelines.
Fixes tag is unlikely to be the actual introdution of the problem but is
far enough back to cover any likely backporting.
Fixes: 7a28fe3c93 ("staging:iio:ad7476: Squash driver into a single file.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-14-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: be7fd3b86a ("iio:adc:ad7298 make the tx and rx buffers __be16")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-13-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 506d2e317a ("iio: adc: Add driver support for AD7292")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-12-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Fixes: 003f1d48de ("staging:iio:adc:ad7280a: Split buff[2] into tx and rx parts")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-11-jic23@kernel.org
____cacheline_aligned is an insufficient guarantee for non-coherent DMA
on platforms with 128 byte cachelines above L1. Switch to the updated
IIO_DMA_MINALIGN definition.
Update the comment to reflect that DMA safety 'may' require separate
cachelines.
Fixes: 54e018da31 ("iio:ad7266: Mark transfer buffer as __be16")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-10-jic23@kernel.org
Discussion of the series:
https://lore.kernel.org/all/20220405135758.774016-1-catalin.marinas@arm.com/
mm, arm64: Reduce ARCH_KMALLOC_MINALIGN brought to my attention that
our current IIO usage of L1CACHE_ALIGN is insufficient as their are Arm
platforms out their with non coherent DMA and larger cache lines at
at higher levels of their cache hierarchy.
Rename the define to make it's purpose more explicit. It will be used
much more widely going forwards (to replace incorrect ____cacheline_aligned
markings.
Note this patch will greatly reduce the padding on some architectures
that have smaller requirements for DMA safe buffers.
The history of changing values of ARCH_KMALLOC_MINALIGN via
ARCH_DMA_MINALIGN on arm64 is rather complex. I'm not tagging this
as fixing a particular patch from that route as it's not clear what to tag.
Most recently a change to bring them back inline was reverted because
of some Qualcomm Kryo cores with an L2 cache with 128-byte lines
sitting above the point of coherency.
c1132702c7 Revert "arm64: cache: Lower ARCH_DMA_MINALIGN to 64 (L1_CACHE_BYTES)"
That reverts:
65688d2a05 arm64: cache: Lower ARCH_DMA_MINALIGN to 64 (L1_CACHE_BYTES) which
refers to the change originally being motivated by Thunder x1 performance
rather than correctness.
Fixes: 6f7c8ee585 ("staging:iio: Add ability to allocate private data space to iio_allocate_device")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-2-jic23@kernel.org
Avoid unnecessary pollution of the global symbol namespace by
moving library functions in to a specific namespace and import
that into the drivers that make use of the functions.
For more info: https://lwn.net/Articles/760045/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Nuno Sá <nuno.sa@analog.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220220173701.502331-5-jic23@kernel.org
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220531213922.72992-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use the ->probe_new() callback.
The driver does not use const struct i2c_device_id * argument,
so convert it to utilise the simplified I²C driver registration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220531213922.72992-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert the module to be property provider agnostic and allow
it to be used on non-OF platforms.
Add mod_devicetable.h include.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220531142353.64925-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
There is nothing directly using of specific interfaces in this driver,
so lets not include the headers.
While at it, drop dependency to OF, which currently makes no sense.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220531212218.72189-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nothing in this driver depends on OF so drop the dependency
to remove the false impression such a dependency exists.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220530181313.2789-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Nothing in this driver depends on OF so drop the dependency
to remove the false impression such a dependency exists.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220530181706.3045-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Returning an error value in an i2c remove callback results in a generic
error message being emitted by the i2c core, but otherwise it doesn't
make a difference. The device goes away anyhow and the devm cleanups are
called.
So instead of triggering the generic i2c error message, emit a more
helpful message if a problem occurs and return 0 to suppress the generic
message.
This patch is a preparation for making i2c remove callbacks return void.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220515155929.338656-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove unnecessary channel check from rzg2l_adc_read_label(), as the
channel error handling is already done in probe(). Therefore no need to
validate at runtime.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220515060337.16513-3-biju.das.jz@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This driver doesn't need to access I/O ports directly via inb()/outb()
and friends. This patch abstracts such access by calling ioport_map()
to enable the use of more typical ioread8()/iowrite8() I/O memory
accessor calls.
Suggested-by: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: William Breathitt Gray <william.gray@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/64673797df382c52fc32fce24348b25a0b05e73a.1652201921.git.william.gray@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the large set of char, misc, and other driver subsystem updates
for 5.19-rc1. The merge request for this has been delayed as I wanted
to get lots of linux-next testing due to some late arrivals of changes
for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers
and cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that
below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no reported
problems.
Note, there are 3 merge conflicts when merging this with your tree:
- MAINTAINERS, should be easy to resolve
- drivers/slimbus/qcom-ctrl.c, should be straightforward
resolution
- drivers/misc/lkdtm/stackleak.c, not an easy resolution. This
has been noted in the linux-next tree for a while, and
resolved there, here's a link to the resolution that Stephen
came up with and that Kees says is correct:
https://lore.kernel.org/r/20220509185344.3fe1a354@canb.auug.org.au
I will be glad to provide a merge point that contains these resolutions
if that makes things any easier for you.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYpnkbA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylOrgCggbbAFwESBY9o2YfpG+2VOLpc0GAAoJgY1XN8
P/gumbLEpFvoBZ5xLIW8
=KCgk
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc / other smaller driver subsystem updates from Greg KH:
"Here is the large set of char, misc, and other driver subsystem
updates for 5.19-rc1. The merge request for this has been delayed as I
wanted to get lots of linux-next testing due to some late arrivals of
changes for the habannalabs driver.
Highlights of this merge are:
- habanalabs driver updates for new hardware types and fixes and
other updates
- IIO driver tree merge which includes loads of new IIO drivers and
cleanups and additions
- PHY driver tree merge with new drivers and small updates to
existing ones
- interconnect driver tree merge with fixes and updates
- soundwire driver tree merge with some small fixes
- coresight driver tree merge with small fixes and updates
- mhi bus driver tree merge with lots of updates and new device
support
- firmware driver updates
- fpga driver updates
- lkdtm driver updates (with a merge conflict, more on that below)
- extcon driver tree merge with small updates
- lots of other tiny driver updates and fixes and cleanups, full
details in the shortlog.
All of these have been in linux-next for almost 2 weeks with no
reported problems"
* tag 'char-misc-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (387 commits)
habanalabs: use separate structure info for each error collect data
habanalabs: fix missing handle shift during mmap
habanalabs: remove hdev from hl_ctx_get args
habanalabs: do MMU prefetch as deferred work
habanalabs: order memory manager messages
habanalabs: return -EFAULT on copy_to_user error
habanalabs: use NULL for eventfd
habanalabs: update firmware header
habanalabs: add support for notification via eventfd
habanalabs: add topic to memory manager buffer
habanalabs: handle race in driver fini
habanalabs: add device memory scrub ability through debugfs
habanalabs: use unified memory manager for CB flow
habanalabs: unified memory manager new code for CB flow
habanalabs/gaudi: set arbitration timeout to a high value
habanalabs: add put by handle method to memory manager
habanalabs: hide memory manager page shift
habanalabs: Add separate poll interval value for protocol
habanalabs: use get_task_pid() to take PID
habanalabs: add prefetch flag to the MAP operation
...
Usual mixed bag. Stand out this time is Andy Shevchenko's continuing
effort to move drivers over the generic firmware interfaces.
Device support
* sprd,sc2720
- upm9620 binding addition.
- Refactor and support for sc2720, sc2721 and sc2730.
* ti,ads1015
- Refactor driver and add support for TLA2024.
Device support (IDs only)
* invensense,mpu6050
- Add ID for ICM-20608-D.
* st,accel:
- Add ID for lis302dl.
* st,lsm6dsx
- Add support for ASM330LHHX (can fallback to LSM6DSR.)
Features
* convert drivers to device properties
- IIO core
- adi,ad7266
- adi,adis16480
- adi,adxl355
- bosch,bmi160
- domintech,dmard06
- fsl,fxas21002c
- invensense,mpu3050
- linear,ltc2983
- linear,ltc2632
- maxbotix,mb1232
- maxim,max31856
- maxim,max31865
- multiplexer
- ping
- rescale
- taos,tsl2772
* core
- Add runtime check on whether realbits fit in storagebits for each
channel.
* adi,ad_sigma_delta
- Add sequencer support and relevant update_scan_mode callbacks for
adi,ad7192 and adi,ad7124.
Cleanup and minor fixes
* MAINTAINERS
- Update Lorenzo Bianconi's email address for IIO drivers.
- Add entry for ad3552r and update maintainer in dt-binding doc.
* tree-wide
- Replace strtobool() with kstrtobool().
- Drop false OF dependencies.
* core
- Tidy up and document IIO modes.
- Take iio_buffer_enabled() out of header allowing current_mode to be
moved to the opaque structure.
- As all kfifo buffers use the same mode value, drop that parameter
and set it unconditionally.
- White space fixes and similar.
- Drop use of list iterator variable for
list_for_each_entry_continue_reverse and use list_prepare_entry to
restart.
* sysfs-trigger
- Replace use of 'found' variable with dedicate list iterator variable.
* adi,ad7124
- Drop misleading shift.
* adi,ad2s1210
- Remove redundant local variable assignment.
* adi,adis16480
- Use local device pointer to reduce repetition.
- Improve handling of clocks.
* domintech,dmard09
- White space.
* dummy driver
- Improve error handling.
* fsl,mma8452
- Add missing documentation of name element.
* invensense,mpu3050
- Stop remove() returning non 0.
* kionix,kxsd9
- White space.
* linear,ltc2688
- Use local variable for struct device.
- Combine of_node_put() error handling paths.
* linear,ltc2983
- Avoid use of constants in messages where a define is available.
* microchip,mcp4131
- Fix compatible in dt example.
* pni,rm3100
- Stop directly accessing iio_dev->current_mode just to find out
if the buffer is enabled.
* renesas,rzg2l
- Relax kconfig constraint to include newer devices.
* sprd,sc27xx
- Fix wrong scaling mask.
- Improve the calibration values.
* samsung,ssp
- Replace a 'found' variable in favor of an explicit value that was
found.
* sensortek,stk3xx
- Add proximity-near-level binding and driver support.
* st,st_sensors:
- Drop unused accel_type enum.
- Return early in *_write_raw()
- Drop unnecessary locking in _avail functions.
- Add local lock to protect odr against concurrent updates allowing
mlock to no longer be used outside of the core.
- Use iio_device_claim_direct_mode() rather than racy checking of
the current mode.
* st,stmpe-adc
- Fix checks on wait_for_completion_timeout().
- Allow use of of_device_id for matching.
* st,stm32-dfsdm
- Stop accessing iio_dev->current_mode to find out if the buffer
is enabled (so we can hide that variable in the opaque structure)
* st,vl53l0x
- Fix checks on wait_for_completion_timeout.
* ti,ads1015
- Add missing ID for ti,ads1115 in binding doc.
- Convert from repeated chip ID look up to selecting static const
data.
- Switch to read_avail() callback.
* ti,ads8688
- Use of_device_id for driver matching.
* ti,palmas-adc
- Drop a warning on minor calibration mismatch leading to slightly
negative values after applying the calibration.
-----BEGIN PGP SIGNATURE-----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=wZYX
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.19a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of IIO new device support, features and cleanup for 5.19
Usual mixed bag. Stand out this time is Andy Shevchenko's continuing
effort to move drivers over the generic firmware interfaces.
Device support
* sprd,sc2720
- upm9620 binding addition.
- Refactor and support for sc2720, sc2721 and sc2730.
* ti,ads1015
- Refactor driver and add support for TLA2024.
Device support (IDs only)
* invensense,mpu6050
- Add ID for ICM-20608-D.
* st,accel:
- Add ID for lis302dl.
* st,lsm6dsx
- Add support for ASM330LHHX (can fallback to LSM6DSR.)
Features
* convert drivers to device properties
- IIO core
- adi,ad7266
- adi,adis16480
- adi,adxl355
- bosch,bmi160
- domintech,dmard06
- fsl,fxas21002c
- invensense,mpu3050
- linear,ltc2983
- linear,ltc2632
- maxbotix,mb1232
- maxim,max31856
- maxim,max31865
- multiplexer
- ping
- rescale
- taos,tsl2772
* core
- Add runtime check on whether realbits fit in storagebits for each
channel.
* adi,ad_sigma_delta
- Add sequencer support and relevant update_scan_mode callbacks for
adi,ad7192 and adi,ad7124.
Cleanup and minor fixes
* MAINTAINERS
- Update Lorenzo Bianconi's email address for IIO drivers.
- Add entry for ad3552r and update maintainer in dt-binding doc.
* tree-wide
- Replace strtobool() with kstrtobool().
- Drop false OF dependencies.
* core
- Tidy up and document IIO modes.
- Take iio_buffer_enabled() out of header allowing current_mode to be
moved to the opaque structure.
- As all kfifo buffers use the same mode value, drop that parameter
and set it unconditionally.
- White space fixes and similar.
- Drop use of list iterator variable for
list_for_each_entry_continue_reverse and use list_prepare_entry to
restart.
* sysfs-trigger
- Replace use of 'found' variable with dedicate list iterator variable.
* adi,ad7124
- Drop misleading shift.
* adi,ad2s1210
- Remove redundant local variable assignment.
* adi,adis16480
- Use local device pointer to reduce repetition.
- Improve handling of clocks.
* domintech,dmard09
- White space.
* dummy driver
- Improve error handling.
* fsl,mma8452
- Add missing documentation of name element.
* invensense,mpu3050
- Stop remove() returning non 0.
* kionix,kxsd9
- White space.
* linear,ltc2688
- Use local variable for struct device.
- Combine of_node_put() error handling paths.
* linear,ltc2983
- Avoid use of constants in messages where a define is available.
* microchip,mcp4131
- Fix compatible in dt example.
* pni,rm3100
- Stop directly accessing iio_dev->current_mode just to find out
if the buffer is enabled.
* renesas,rzg2l
- Relax kconfig constraint to include newer devices.
* sprd,sc27xx
- Fix wrong scaling mask.
- Improve the calibration values.
* samsung,ssp
- Replace a 'found' variable in favor of an explicit value that was
found.
* sensortek,stk3xx
- Add proximity-near-level binding and driver support.
* st,st_sensors:
- Drop unused accel_type enum.
- Return early in *_write_raw()
- Drop unnecessary locking in _avail functions.
- Add local lock to protect odr against concurrent updates allowing
mlock to no longer be used outside of the core.
- Use iio_device_claim_direct_mode() rather than racy checking of
the current mode.
* st,stmpe-adc
- Fix checks on wait_for_completion_timeout().
- Allow use of of_device_id for matching.
* st,stm32-dfsdm
- Stop accessing iio_dev->current_mode to find out if the buffer
is enabled (so we can hide that variable in the opaque structure)
* st,vl53l0x
- Fix checks on wait_for_completion_timeout.
* ti,ads1015
- Add missing ID for ti,ads1115 in binding doc.
- Convert from repeated chip ID look up to selecting static const
data.
- Switch to read_avail() callback.
* ti,ads8688
- Use of_device_id for driver matching.
* ti,palmas-adc
- Drop a warning on minor calibration mismatch leading to slightly
negative values after applying the calibration.
* tag 'iio-for-5.19a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (95 commits)
iio: ti-ads8688: use of_device_id for OF matching
iio: stmpe-adc: use of_device_id for OF matching
dt-bindings: iio: Fix incorrect compatible strings in examples
iio: gyro: mpu3050: Make mpu3050_common_remove() return void
iio: dac: ltc2632: Make use of device properties
iio: temperature: max31865: Make use of device properties
iio: proximity: mb1232: Switch to use fwnode_irq_get()
iio: imu: adis16480: Improve getting the optional clocks
iio: imu: adis16480: Use temporary variable for struct device
iio: imu: adis16480: Make use of device properties
staging: iio: ad2s1210: remove redundant assignment to variable negative
iio: adc: sc27xx: add support for PMIC sc2730
iio: adc: sc27xx: add support for PMIC sc2720 and sc2721
iio: adc: sc27xx: refactor some functions for support more PMiCs
iio: adc: sc27xx: structure adjustment and optimization
iio: adc: sc27xx: Fine tune the scale calibration values
iio: adc: sc27xx: fix read big scale voltage not right
dt-bindings:iio:adc: add sprd,ump9620-adc dt-binding
iio: proximity: stk3310: Export near level property for proximity sensor
dt-bindings: iio: light: stk33xx: Add proximity-near-level
...
Add reverse scaling function for PMIC5 Gen2 ADC_TM, to convert
temperature to raw ADC code, for setting thresholds for
thermistor channels.
Signed-off-by: Jishnu Prakash <quic_jprakash@quicinc.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/1648991869-20899-3-git-send-email-quic_jprakash@quicinc.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Return irq instead of ret which always equals to zero here.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Since commit 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling") we
preserve the bias current set by the firmware at boot. This fixes issues
we were seeing on various models.
Some models like the Nuvision Solo 10 Draw tablet actually need the
old hardcoded 80ųA bias current for battery temperature monitoring
to work properly.
Add a quirk entry for the Nuvision Solo 10 Draw to the DMI quirk table
to restore setting the bias current to 80ųA on this model.
Fixes: 9bcf15f75c ("iio: adc: axp288: Fix TS-pin handling")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215882
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220506095040.21008-1-hdegoede@redhat.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The of_device_id was added to allow module autoloading, but it should be
also used to allow driver matching via Devicetree.
This also fixes W=1 warning:
drivers/iio/adc/ti-ads8688.c:501:34: error: ‘ads8688_of_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220501103447.111392-2-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The of_device_id was added to allow module autoloading, but it should be
also used to allow driver matching via Devicetree.
This also fixes W=1 warning:
drivers/iio/adc/stmpe-adc.c:357:34: error: ‘stmpe_adc_ids’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220501103447.111392-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Refactor the common adc_nvmem_cell_calib_data,adc_to_volt and call
these in the origin sc27xx_adc_scale_calibration,sc27xx_adc_to_volt
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Link: https://lore.kernel.org/r/20220419142458.884933-6-gengcixi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Introduce one variant device data structure to be compatible
with SC2731 PMIC since it has different scale and ratio calculation
and so on. also rename the SC27xx to SC2731 for some definition
and function.
Co-developed-by: Yuming Zhu <yuming.zhu1@unisoc.com>
Signed-off-by: Yuming Zhu <yuming.zhu1@unisoc.com>
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Link: https://lore.kernel.org/r/20220419142458.884933-5-gengcixi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Small adjustment the scale calibration value for the sc2731,
use new name sc2731_[big|small]_scale_graph_calib, and remove
the origin [big|small]_scale_graph_calib struct for unused.
Fixes: 8ba0dbfd07 (iio: adc: sc27xx: Add ADC scale calibration)
Signed-off-by: Cixi Geng <cixi.geng1@unisoc.com>
Link: https://lore.kernel.org/r/20220419142458.884933-4-gengcixi@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
wait_for_completion_timeout() returns unsigned long not long.
it returns 0 if timed out, and positive if completed.
The check for <= 0 is ambiguous and should be == 0 here
indicating timeout which is the only error case
Fixes: e813dde6f8 ("iio: stmpe-adc: Use wait_for_completion_timeout")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Link: https://lore.kernel.org/r/20220412065150.14486-1-linmq006@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
ADC block is common on Renesas RZ/G2L and RZ/V2L SoC's, so instead of
adding dependency for each SoC's add dependency on ARCH_RZG2L. The
ARCH_RZG2L config option is already selected by ARCH_R9A07G044 and
ARCH_R9A07G054.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220406070315.13862-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Convert probe functions to device-managed variants, with exception of
the regulator, which required a devm_add_action_or_reset() hook
registration.
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Nuno Sá <nuno.sa@analog.com>
Signed-off-by: Maíra Canal <maira.canal@usp.br>
Link: https://lore.kernel.org/r/20220407115621.10781-1-maira.canal@usp.br
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
strtobool() is deprecated and just a wrapper around kstrtobool().Replace
it with kstrtobool() so the deprecated function can be removed eventually.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220409105812.2113895-1-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Among all the users of the kfifo buffers, no one uses the
INDIO_BUFFER_HARDWARE mode. So let's take this as a general rule and
simplify a little bit the internals - overall the documentation - by
eliminating unused specific cases. Use the INDIO_BUFFER_SOFTWARE mode by
default with kfifo buffers, which will basically mimic what all the "non
direct" modes do.
Cc: Benson Leung <bleung@chromium.org>
Cc: Guenter Roeck <groeck@chromium.org>
Cc: Jyoti Bhayana <jbhayana@google.com>
Cc: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220207143840.707510-13-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
In order to later move this variable within the opaque structure, let's
create a helper for accessing it in read-only mode. This helper will be
exposed to device drivers and kept accessible for the few that could need
it. The write access to this variable however should be fully reserved to
the core so in a second step we will hide this variable into the opaque
structure.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/20220207143840.707510-11-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is an internal variable of the core, let's use the
iio_buffer_enabled() helper which is exported for the following purpose:
telling if the current mode is a buffered mode, which is precisely what
this driver looks for.
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/20220207143840.707510-4-miquel.raynal@bootlin.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Name of variable change missed in refactoring patch.
Fixes: 112bf4aa4a ("staging:iio:adc:ad7280a: Switch to standard event control")
Reported-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220226175604.662422-1-jic23@kernel.org
Replace sysfs attributes with read_avail() callback. This also permits
removal of ads1115_info, since the scale attribute tables are now part
of chip data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Link: https://lore.kernel.org/r/20220328194725.149150-10-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of storing only data_rate in private data, store pointer to the
whole chip data and use the data_rate from chip data throughout the driver.
No functional change. This is done in preparation for switching to
read_avail().
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-9-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Replace chip type enumeration in match data with pointer to static constant
structure which contains all the different chip properties in one place, and
then replace handling of chip type in probe() with simple copy of fields in
the new match data structure into struct iio_dev.
This reduces code and increases static data.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-8-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add compile-time static_assert wrapper to verify that shifted realbits
fit into storagebits. The macro is implemented in a more generic way so
it can be used to verify other values if required.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-7-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support for TI TLA2024 ADC. This chip is compatible with ADS1015
except it has no comparator in it, hence the comparator configuration
bits are missing in Configuration Register and the Hi_Thresh/Lo_Thresh
registers are missing as well and so is event support.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-6-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Pass event_spec and num_event_specs to ADS1015_V_CHAN and ADS1015_V_DIFF_CHAN
macros, to make it possible to pass no event_spec at all for chips which have
no comparator and thus no events. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-5-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
These macros differ only in the number of valid bits of each ADC sample
and the shift of those bits, i.e. ADS1015 is 12bit ADC shifted by 4 left,
ADS1115 is 16bit ADC shifted by 0. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-4-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Switch the driver from code implementing test whether a regmap register
is writeable to static const tables describing the test. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andy Shevchenko <andy@kernel.org>
Cc: Daniel Baluta <daniel.baluta@nxp.com>
Link: https://lore.kernel.org/r/20220328194725.149150-3-marex@denx.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Although technically checking for ADC values below 0 is correct,
because they are outside of the calibration values, there is usually
noise which spuriously fills the console log with error messages if
calculated input voltage gets close to 0V.
Ignore small negative calculated values, but clamp them to 0.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Link: https://lore.kernel.org/r/1cee45bfc3fa2ab59dcc17242fb52468035360a1.1646743982.git.hns@goldelico.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some sigma-delta chips support sampling of multiple
channels in continuous mode.
When the operating with more than one channel enabled,
the channel sequencer cycles through the enabled channels
in sequential order, from first channel to the last one.
If a channel is disabled, it is skipped by the sequencer.
If more than one channel is used in continuous mode,
instruct the device to append the status to the SPI transfer
(1 extra byte) every time we receive a sample.
All sigma-delta chips possessing a sampling sequencer have
this ability. Inside the status register there will be
the number of the converted channel. In this way, even
if the CPU won't keep up with the sampling rate, it won't
send to userspace wrong channel samples.
When multiple channels are enabled in continuous mode,
the device needs to perform a measurement on all slots
before we can push to userspace the sample.
If, during sequencing and data reading, a channel measurement
is lost, a desync occurred. In this case, ad_sigma_delta drops
the incomplete sample and waits for the device to send the
measurement on the first active slot.
Co-developed-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20220322105029.86389-5-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The callback .set_channel cannot be used to enable multiple
channels at once, only one is allowed simultaneously.
By adding an update_scan_mode callback, every time the
continuous mode is activated, channels will be enabled/disabled
accordingly.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20220322105029.86389-4-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The callback .set_channel cannot be used to enable and
disable multiple channels at once as they are presented
in the active_scan_mask.
By adding an update_scan_mode callback, every time the
continuous mode is activated, channels will be
enabled/disabled accordingly.
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20220322105029.86389-3-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The 24 bits data is stored in 32 bits in BE. There
is no need to shift it. This confuses user-space apps.
Fixes: b3af341bbd ("iio: adc: Add ad7124 support")
Signed-off-by: Alexandru Tachici <alexandru.tachici@analog.com>
Link: https://lore.kernel.org/r/20220322105029.86389-2-alexandru.tachici@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
There will be two merge conflicts with your tree, one in MAINTAINERS
which is obvious to fix up, and one in drivers/phy/freescale/Kconfig
which also should be easy to resolve.
All of these have been in linux-next for a while with no reported
problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYkG3fQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykNEgCfaRG8CRxewDXOO4+GSeA3NGK+AIoAnR89donC
R4bgCjfg8BWIBcVVXg3/
=WWXC
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc and other driver updates from Greg KH:
"Here is the big set of char/misc and other small driver subsystem
updates for 5.18-rc1.
Included in here are merges from driver subsystems which contain:
- iio driver updates and new drivers
- fsi driver updates
- fpga driver updates
- habanalabs driver updates and support for new hardware
- soundwire driver updates and new drivers
- phy driver updates and new drivers
- coresight driver updates
- icc driver updates
Individual changes include:
- mei driver updates
- interconnect driver updates
- new PECI driver subsystem added
- vmci driver updates
- lots of tiny misc/char driver updates
All of these have been in linux-next for a while with no reported
problems"
* tag 'char-misc-5.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (556 commits)
firmware: google: Properly state IOMEM dependency
kgdbts: fix return value of __setup handler
firmware: sysfb: fix platform-device leak in error path
firmware: stratix10-svc: add missing callback parameter on RSU
arm64: dts: qcom: add non-secure domain property to fastrpc nodes
misc: fastrpc: Add dma handle implementation
misc: fastrpc: Add fdlist implementation
misc: fastrpc: Add helper function to get list and page
misc: fastrpc: Add support to secure memory map
dt-bindings: misc: add fastrpc domain vmid property
misc: fastrpc: check before loading process to the DSP
misc: fastrpc: add secure domain support
dt-bindings: misc: add property to support non-secure DSP
misc: fastrpc: Add support to get DSP capabilities
misc: fastrpc: add support for FASTRPC_IOCTL_MEM_MAP/UNMAP
misc: fastrpc: separate fastrpc device from channel context
dt-bindings: nvmem: brcm,nvram: add basic NVMEM cells
dt-bindings: nvmem: make "reg" property optional
nvmem: brcm_nvram: parse NVRAM content into NVMEM cells
nvmem: dt-bindings: Fix the error of dt-bindings check
...
The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus types,
causing updates to most SPI device drivers. The branch with that on has
been cross merged with a couple of other trees which added new SPI
drivers this cycle, I'm not expecting any build issues resulting from
the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmI4b+8ACgkQJNaLcl1U
h9AB+Qf/WhPzDSCdhK1repnSmEpRNs/J6hItmY2H6pTQaWALpfTB0+p1Nb5tAotg
fHbu6a2AsiiwWt+tDal44GFYhS0CDSOT4hqgLV8msyDDPPJqqr7A2dbu7YrCjTVI
TgNZNwxW7c2LgqBXR9GV7NPWYoxYxveoYh+L+05MSuSQxSOvPl6LUZiZPnPufQM6
dCpEh19atrtasFg3rFnslWBd2C3h8hb6YT7vUZs9gxhg3FvSgpYQwzz5SfFgHXK6
Rg07m8fDTSjf2qo1C4pc/d1Ni1xBe7aHKMtjtR3jJ4q8QqiawfCcvvOep/Iaec1+
s3qnDthohWMJoF1W6ERf3HiAgNIfhg==
=4tlR
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The overwhelming bulk of this pull request is a change from Uwe
Kleine-König which changes the return type of the remove() function to
void as part of some wider work he's doing to do this for all bus
types, causing updates to most SPI device drivers. The branch with
that on has been cross merged with a couple of other trees which added
new SPI drivers this cycle, I'm not expecting any build issues
resulting from the change.
Otherwise it's been a relatively quiet release with some new device
support, a few minor features and the welcome completion of the
conversion of the subsystem to use GPIO descriptors rather than
numbers:
- Change return type of remove() to void.
- Completion of the conversion of SPI controller drivers to use GPIO
descriptors rather than numbers.
- Quite a few DT schema conversions.
- Support for multiple SPI devices on a bus in ACPI systems.
- Big overhaul of the PXA2xx SPI driver.
- Support for AMD AMDI0062, Intel Raptor Lake, Mediatek MT7986 and
MT8186, nVidia Tegra210 and Tegra234, Renesas RZ/V2L, Tesla FSD and
Sunplus SP7021"
[ And this is obviously where that spi change that snuck into the
regulator tree _should_ have been :^]
* tag 'spi-v5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (124 commits)
spi: fsi: Implement a timeout for polling status
spi: Fix erroneous sgs value with min_t()
spi: tegra20: Use of_device_get_match_data()
spi: mediatek: add ipm design support for MT7986
spi: Add compatible for MT7986
spi: sun4i: fix typos in comments
spi: mediatek: support tick_delay without enhance_timing
spi: Update clock-names property for arm pl022
spi: rockchip-sfc: fix platform_get_irq.cocci warning
spi: s3c64xx: Add spi port configuration for Tesla FSD SoC
spi: dt-bindings: samsung: Add fsd spi compatible
spi: topcliff-pch: Prevent usage of potentially stale DMA device
spi: tegra210-quad: combined sequence mode
spi: tegra210-quad: add acpi support
spi: npcm-fiu: Fix typo ("npxm")
spi: Fix Tegra QSPI example
spi: qup: replace spin_lock_irqsave by spin_lock in hard IRQ
spi: cadence: fix platform_get_irq.cocci warning
spi: Update NXP Flexspi maintainer details
dt-bindings: mfd: maxim,max77802: Convert to dtschema
...
This cycle we had quite a few series that applied similar changes
to lots of drivers. To keep this description manageable I have
called those out in their own section rather than per driver.
Particularly pleased to see the long running AFE precision series
going in this cycle.
Series includes some late breaking fixes.
New device support
* adi,ada4250 amplifier
- New driver and dt bindings for this programmable gain amplifier.
* adi,admv1014 microwave down-converter
- New driver, dt bindings and some device specific ABI that
may be generalized as more drivers for devices similar to this
are added.
* adi,admv4420 K Band down-converter.
- New driver and dt bindings.
* adi,adxl367 accelerometer driver.
- New driver, dt-bindings + some new IIO ABI definitions to support
reference magnitude events where an estimate of the acceleration
due to gravity has been removed.
- A few fixes as follow up patches.
* adi,ltc2688 DAC with toggle and dither modes.
- New driver and bindings. Includes some new driver specific (for now)
ABI for handling toggle mode and the addition of a dither waveform to
the DAC output.
* AFE (analog front end) add support for additional types of analog device
in front of an ADC.
- RTD temperature sensors with dt bindings.
- Temperature transducers wit dt bindings.
- Related cleanup and features listed in other sections below.
* maxim,ds3502 potentiometer.
- Add support to ds1803 driver which required significant rework.
* mediatek,mt2701-auxadc driver
- Add mediatek,mt8186-auxadc - id table and chip specific info only.
* semtech,sx9324, semtech,ax9360
- Substantial refactoring of sx9310 to extract core logic for reuse
into a separate module
- New driver using this supporting sx9324 proximity sensors.
- New driver using this supporting sx9360 proximity sensors.
* silan,sc7a20
- Compatible with the st,lis2dh (or nearly anyway) so add ID and
chip specific info to enable support. Also silan vendor ID added
for dt-bindings.
Staging graduation
* adi,ad7280a monitoring ADC for stacked lithium-ion batteries in
electric cars and similar.
- Substantial rework of driver required to bring inline with current
IIO best practice. An unusual device in IIO so some interesting features
we may see more of in future.
Multiple driver/core cleanup
- Use sysfs_emit() in simple locations where there is no path to change
to various core created attributes.
- Trivial white space fixes around inconsistency between space after { and
before } in id tables.
- Introduce new handling for fractional types to avoid repeated similar
implementations. Use this in 3 drivers. Note this is also targeted
at future use in the AFE driver and was motivated by discussions
around the precision related work on that driver.
- of related header cleanups - drop of*.h and add mod_devicetable.h as
appropriate.
- Move a number of symbol exports into IIO_* namespaces. Two categories,
1) Library used by multiple drivers e.g. st_sensors
2) Core driver module exporting functions used by bus specific modules.
A few related cleanups in this set.
- Switch from CONFIG_PM_* guards to new DEFINE_SIMPLE_DEV_PM_OPS() and
similar to simplify drivers and take advantage of these new macros
allowing the compiler to do the job or removing unused code without
the need for __maybe_unused markings. Conversion of other drivers to
these new macros ongoing.
Features
* adi,adf4350
- Switch from of specific to generic device properties enabling use with
other firmware types.
* adi,adx345
- Switch from of specific to generic device properties.
- Add ACPI ID ADS0345
- Related driver cleanup.
* adi,hmc425a
- Switch from of specific to generic device properties.
* afe analog rescaler driver
- Wider range of types supported for scale.
- Support offset.
- Kunit tests.
* atlas,ezo-sensor
- Convert from of to device properties.
* fsl,mma8452
- Support mount matrix.
* infineon,dps310:
- Add ACPI ID IFX3100.
* invensense,mpu6050
- Convert to generic device properties.
* maxim,ds1803
- Add out_raw_available before supporting more devices.
- Convert from of specific to device properties.
* samsung,ssp_sensors
- Convert from of specific to device properties.
* st,stm32-timer trigger
- Convert from of specific to device properties.
* ti,hdc101x
- Add ACPI ID TXNW1010.
* ti,tsc2046:
- Add read_raw support to enable use of iio_hwmon and similar.
Fixes / cleanup.
* mailmap
- Update for Cai Huoqing
* MAINTAINERS
- Fix Analog Devices related links.
- Add entry for ADRF6780
- Add entry for ADMV1013
- Add entry for AD7293
- Add entry for ADMV8818
- Update files listed for adis-lib
* iio core:
- Fix wrong comment about current_mode being something a driver should
ever access.
- Use struct_size() rather than open coding in industrialio-hw-consumer
* adi,axl355
- Use units.h definitions instead of local versions.
* adi,adis-lib
- Simplify *updated_bits() macro
- Whitespace cleanup.
* afe - Note many of these fixes only apply to particular configurations
so the problems have probably not been seen in the wild, but will be
visible with new usecases enabled this cycle.
- Fix application of consumer scale for IIO_VAL_INT.
- Apply a scale of 1 when no scale is provided.
- Make best effort to establish a valid offset value for fractional
cases.
- Use s64 for scale calculations where parameters may be signed.
- Tidy up include order.
- Improve accuracy for small fractional sales
- Reduce risk of integer overflow.
* ams,as3935
- Use devm_delayed_work_autocancel() to replace open coded equivalent.
* aspeed,adc
- Fix wrong use of divider flag.
* atmel,sama5d2-adc
- Relax atmel,trigger-edge-type to optional.
- Drop Ludovic Desroches from listed maintainers of the dt-binding
inline with previous MAINTAINERS entry update.
* fsl,mma8452
- Fix probing when i2c_device_id used.
- dev_get_drvdata() on the iio_dev->dev, no longer returns iio_dev.
Use dev_to_iio_dev() instead. Note the original path in here
worked more by luck than design.
* invensense,mpu6050
- Drop ACPI_PTR() protection to avoid an unused warning.
- Use fact ACPI_COMPANION() returns null when ACPI_HANDLE() does to
simplify handling.
* motorola,cpcap-adc
- Drop unused assignment.
* qcom,spmi-adc
- Fix wrong example of 'reg' in binding document.
* renesas,rzg2l-adc
- Trivial typo fix.
* semtech,sx9360
- Fix wrong register handling for event generation.
* st_sensors
- Allow manual disabling of I2C or SPI module if not needed for a particular
board. Default is still to enable the bus specific module if
appropriate bus is supported.
* st,lsm6dsx
- dev_get_drvdata() on the iio_dev->dev, no longer returns iio_dev.
Use dev_to_iio_dev() instead.
* ti,palmas-gpadc
- Split the interrupt fields in the dt-binding example
* ti,tsc2046
- Rework state machine to improve readability after recent debugging of
an issue fixed elsewhere.
- Add a sanity check to avoid very large memory allocations if a crazy
delay is specified.
* ti,twl6030
- Add error handling if devm_request_threaded_irq() fails.
* xilinx,ams
- Use devm_delayed_work_autocancel() instead of open coding equivalent.
- Fix missing required clock entry in dt-binding.
- Fix miss counting of channels resulting in ps channels not
being enabled.
- Fix incorrect values written to sequencer registers.
- Fix sequence for single channel reading.
-----BEGIN PGP SIGNATURE-----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=UnWv
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.18a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
First set of new device support, fixes, cleanups and features for IIO in 5.18
This cycle we had quite a few series that applied similar changes
to lots of drivers. To keep this description manageable I have
called those out in their own section rather than per driver.
Particularly pleased to see the long running AFE precision series
going in this cycle.
Series includes some late breaking fixes.
New device support
* adi,ada4250 amplifier
- New driver and dt bindings for this programmable gain amplifier.
* adi,admv1014 microwave down-converter
- New driver, dt bindings and some device specific ABI that
may be generalized as more drivers for devices similar to this
are added.
* adi,admv4420 K Band down-converter.
- New driver and dt bindings.
* adi,adxl367 accelerometer driver.
- New driver, dt-bindings + some new IIO ABI definitions to support
reference magnitude events where an estimate of the acceleration
due to gravity has been removed.
- A few fixes as follow up patches.
* adi,ltc2688 DAC with toggle and dither modes.
- New driver and bindings. Includes some new driver specific (for now)
ABI for handling toggle mode and the addition of a dither waveform to
the DAC output.
* AFE (analog front end) add support for additional types of analog device
in front of an ADC.
- RTD temperature sensors with dt bindings.
- Temperature transducers wit dt bindings.
- Related cleanup and features listed in other sections below.
* maxim,ds3502 potentiometer.
- Add support to ds1803 driver which required significant rework.
* mediatek,mt2701-auxadc driver
- Add mediatek,mt8186-auxadc - id table and chip specific info only.
* semtech,sx9324, semtech,ax9360
- Substantial refactoring of sx9310 to extract core logic for reuse
into a separate module
- New driver using this supporting sx9324 proximity sensors.
- New driver using this supporting sx9360 proximity sensors.
* silan,sc7a20
- Compatible with the st,lis2dh (or nearly anyway) so add ID and
chip specific info to enable support. Also silan vendor ID added
for dt-bindings.
Staging graduation
* adi,ad7280a monitoring ADC for stacked lithium-ion batteries in
electric cars and similar.
- Substantial rework of driver required to bring inline with current
IIO best practice. An unusual device in IIO so some interesting features
we may see more of in future.
Multiple driver/core cleanup
- Use sysfs_emit() in simple locations where there is no path to change
to various core created attributes.
- Trivial white space fixes around inconsistency between space after { and
before } in id tables.
- Introduce new handling for fractional types to avoid repeated similar
implementations. Use this in 3 drivers. Note this is also targeted
at future use in the AFE driver and was motivated by discussions
around the precision related work on that driver.
- of related header cleanups - drop of*.h and add mod_devicetable.h as
appropriate.
- Move a number of symbol exports into IIO_* namespaces. Two categories,
1) Library used by multiple drivers e.g. st_sensors
2) Core driver module exporting functions used by bus specific modules.
A few related cleanups in this set.
- Switch from CONFIG_PM_* guards to new DEFINE_SIMPLE_DEV_PM_OPS() and
similar to simplify drivers and take advantage of these new macros
allowing the compiler to do the job or removing unused code without
the need for __maybe_unused markings. Conversion of other drivers to
these new macros ongoing.
Features
* adi,adf4350
- Switch from of specific to generic device properties enabling use with
other firmware types.
* adi,adx345
- Switch from of specific to generic device properties.
- Add ACPI ID ADS0345
- Related driver cleanup.
* adi,hmc425a
- Switch from of specific to generic device properties.
* afe analog rescaler driver
- Wider range of types supported for scale.
- Support offset.
- Kunit tests.
* atlas,ezo-sensor
- Convert from of to device properties.
* fsl,mma8452
- Support mount matrix.
* infineon,dps310:
- Add ACPI ID IFX3100.
* invensense,mpu6050
- Convert to generic device properties.
* maxim,ds1803
- Add out_raw_available before supporting more devices.
- Convert from of specific to device properties.
* samsung,ssp_sensors
- Convert from of specific to device properties.
* st,stm32-timer trigger
- Convert from of specific to device properties.
* ti,hdc101x
- Add ACPI ID TXNW1010.
* ti,tsc2046:
- Add read_raw support to enable use of iio_hwmon and similar.
Fixes / cleanup.
* mailmap
- Update for Cai Huoqing
* MAINTAINERS
- Fix Analog Devices related links.
- Add entry for ADRF6780
- Add entry for ADMV1013
- Add entry for AD7293
- Add entry for ADMV8818
- Update files listed for adis-lib
* iio core:
- Fix wrong comment about current_mode being something a driver should
ever access.
- Use struct_size() rather than open coding in industrialio-hw-consumer
* adi,axl355
- Use units.h definitions instead of local versions.
* adi,adis-lib
- Simplify *updated_bits() macro
- Whitespace cleanup.
* afe - Note many of these fixes only apply to particular configurations
so the problems have probably not been seen in the wild, but will be
visible with new usecases enabled this cycle.
- Fix application of consumer scale for IIO_VAL_INT.
- Apply a scale of 1 when no scale is provided.
- Make best effort to establish a valid offset value for fractional
cases.
- Use s64 for scale calculations where parameters may be signed.
- Tidy up include order.
- Improve accuracy for small fractional sales
- Reduce risk of integer overflow.
* ams,as3935
- Use devm_delayed_work_autocancel() to replace open coded equivalent.
* aspeed,adc
- Fix wrong use of divider flag.
* atmel,sama5d2-adc
- Relax atmel,trigger-edge-type to optional.
- Drop Ludovic Desroches from listed maintainers of the dt-binding
inline with previous MAINTAINERS entry update.
* fsl,mma8452
- Fix probing when i2c_device_id used.
- dev_get_drvdata() on the iio_dev->dev, no longer returns iio_dev.
Use dev_to_iio_dev() instead. Note the original path in here
worked more by luck than design.
* invensense,mpu6050
- Drop ACPI_PTR() protection to avoid an unused warning.
- Use fact ACPI_COMPANION() returns null when ACPI_HANDLE() does to
simplify handling.
* motorola,cpcap-adc
- Drop unused assignment.
* qcom,spmi-adc
- Fix wrong example of 'reg' in binding document.
* renesas,rzg2l-adc
- Trivial typo fix.
* semtech,sx9360
- Fix wrong register handling for event generation.
* st_sensors
- Allow manual disabling of I2C or SPI module if not needed for a particular
board. Default is still to enable the bus specific module if
appropriate bus is supported.
* st,lsm6dsx
- dev_get_drvdata() on the iio_dev->dev, no longer returns iio_dev.
Use dev_to_iio_dev() instead.
* ti,palmas-gpadc
- Split the interrupt fields in the dt-binding example
* ti,tsc2046
- Rework state machine to improve readability after recent debugging of
an issue fixed elsewhere.
- Add a sanity check to avoid very large memory allocations if a crazy
delay is specified.
* ti,twl6030
- Add error handling if devm_request_threaded_irq() fails.
* xilinx,ams
- Use devm_delayed_work_autocancel() instead of open coding equivalent.
- Fix missing required clock entry in dt-binding.
- Fix miss counting of channels resulting in ps channels not
being enabled.
- Fix incorrect values written to sequencer registers.
- Fix sequence for single channel reading.
* tag 'iio-for-5.18a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (245 commits)
iio: adc: xilinx-ams: Fix single channel switching sequence
iio: adc: xilinx-ams: Fixed wrong sequencer register settings
iio: adc: xilinx-ams: Fixed missing PS channels
dt-bindings: iio: adc: zynqmp_ams: Add clock entry
iio: accel: mma8452: use the correct logic to get mma8452_data
iio: adc: aspeed: Add divider flag to fix incorrect voltage reading.
iio: imu: st_lsm6dsx: use dev_to_iio_dev() to get iio_dev struct
dt-bindings: iio: Add ltc2688 documentation
iio: ABI: add ABI file for the LTC2688 DAC
iio: dac: add support for ltc2688
dt-bindings: iio: afe: add bindings for temperature transducers
dt-bindings: iio: afe: add bindings for temperature-sense-rtd
iio: afe: rescale: add temperature transducers
iio: afe: rescale: add RTD temperature sensor support
iio: test: add basic tests for the iio-rescale driver
iio: afe: rescale: reduce risk of integer overflow
iio: afe: rescale: fix accuracy for small fractional scales
iio: afe: rescale: add offset support
iio: afe: rescale: add INT_PLUS_{MICRO,NANO} support
iio: afe: rescale: expose scale processing function
...
Some of the AMS channels need to be read by switching into single-channel
mode from the normal polling sequence. There was a logic issue in this
switching code that could cause the first read of these channels to read
back as zero.
It appears that the sequencer should be set back to default mode before
changing the channel selection, and the channel should be set before
switching the sequencer back into single-channel mode.
Also, write 1 to the EOC bit in the status register to clear it before
waiting for it to become set, so that we actually wait for a new
conversion to complete, and don't proceed based on a previous conversion
completing.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20220127173450.3684318-5-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Register settings used for the sequencer configuration register
were incorrect, causing some inputs to not be read properly.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20220127173450.3684318-4-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The code forgot to increment num_channels for the PS channel inputs,
resulting in them not being enabled as they should.
Fixes: d5c70627a7 ("iio: adc: Add Xilinx AMS driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20220127173450.3684318-3-robert.hancock@calian.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The formula for the ADC sampling period in ast2400/ast2500 is:
ADC clock period = PCLK * 2 * (ADC0C[31:17] + 1) * (ADC0C[9:0])
When ADC0C[9:0] is set to 0 the sampling voltage will be lower than
expected, because the hardware may not have enough time to
charge/discharge to a stable voltage. This patch use the flag
CLK_DIVIDER_ONE_BASED which will use the raw value read from the
register, with the value of zero considered invalid to conform to the
corrected formula.
Fixes: 573803234e ("iio: Aspeed ADC")
Reported-by: Konstantin Klubnichkin <kitsok@yandex-team.ru>
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20220221012705.22008-1-billy_tsai@aspeedtech.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
As the potential failure of the devm_request_threaded_irq(),
it should be better to check the return value and return
error if fails.
Fixes: fa659a40b8 ("iio: adc: twl6030-gpadc: Use devm_* API family")
Signed-off-by: Jiasheng Jiang <jiasheng@iscas.ac.cn>
Link: https://lore.kernel.org/r/20220224062849.3280966-1-jiasheng@iscas.ac.cn
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use devm_delayed_work_autocancel() instead of hand writing it. This is
less verbose and saves a few lines of code.
devm_delayed_work_autocancel() uses devm_add_action() instead of
devm_add_action_or_reset(). This is fine, because if the underlying memory
allocation fails, no work has been scheduled yet. So there is nothing to
undo.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/2626e6a057e40cd2271ef0e5f81d12e607bad5b4.1644776929.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This is a rather unusual device (in IIO anyway). However, it has
a near to standard userspace ABI.
Note the work to move this out of staging was done against a minimal
QEMU model, which doesn't model all the features of the device.
I have no intention to upstream the QEMU model as it was developed
just to enable this driver cleanup.
https://github.com/jic23/qemu/tree/ad7280a-hacks
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Marcelo Schmitt <marcelo.schmitt1@gmail.com>
Link: https://lore.kernel.org/r/20220206190328.333093-21-jic23@kernel.org
The combinations of either
* pm_sleep_ptr() and DEFINE_SIMPLE_DEV_PM_OPS()
* pm_ptr() and RUNTIME_PM_OPS()/SYSTEM_SLEEP_PM_OPS
Make sure the functions are always visible to the compiler and removed by
it rather than requring #ifdef magic.
This removes the need to mark the functions as __maybe_unused and saves
additional space with some build options as the dev_pm_ops structure
itself can be dropped automatically if CONFIG_PM is not enabled.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Olivier Moysan <olivier.moysan@st.com>
Cc: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-51-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-46-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
The new DEFINE_RUNTIME_DEV_PM_OPS() macro reduces boilerplate.
Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-45-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM support is simpler and less error prone than the
use of #ifdef based config guards.
This case uses the new DEFINE_RUNTIME_DEV_PM_OPS() to reduce
boilerplate.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-44-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Stefan-Gabriel Mirea <stefan-gabriel.mirea@nxp.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-16-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-15-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-14-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
In this case SIMPLE_DEV_PM_OPS() could have been used previously.
Now we have DEFINE_SIMPLE_DEV_PM_OPS() which also deals with letting
the compiler remove the structure and functions so use that instead.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-13-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of #ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-12-jic23@kernel.org
Letting the compiler remove these functions when the kernel is built
without CONFIG_PM_SLEEP support is simpler and less error prone than the
use of ifdef based config guards.
Removing instances of this approach from IIO also stops them being
copied into new drivers.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20220130193147.279148-11-jic23@kernel.org
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various bus specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-4-jic23@kernel.org
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
An alternative here would be to conclude that we are unlikely to see
support for the other ad7091r parts in the near future and just merge
the two modules into one supporting just the i2c -5 variant.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-3-jic23@kernel.org
In order to avoid unnecessary pollution of the global symbol namespace
move the core/library functions into a specific namespace and import
that into the various specific device drivers that use them.
For more information see https://lwn.net/Articles/760045/
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Renato Lui Geh <renatogeh@gmail.com>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220130205701.334592-2-jic23@kernel.org
The value returned by an spi driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)
So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Acked-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Claudius Heine <ch@denx.de>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # For MMC
Acked-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220123175201.34839-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
The variable cal_data_diff is being assigned a value that is never read,
it is being re-assigned later on with a new value in both paths of an
if statement. The assignment is redundant, so remove it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220207135943.340629-1-colin.i.king@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
If iio_device_register() fails, a previous ioremap() is left unbalanced.
Update the error handling path and add the missing iounmap() call, as
already done in the remove function.
Fixes: 74aeac4da6 ("iio: adc: Add MEN 16z188 ADC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/320fc777863880247c2aff4a9d1a54ba69abf080.1643445149.git.christophe.jaillet@wanadoo.fr
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
On one side we have indio_dev->num_channels includes all physical channels +
timestamp channel. On other side we have an array allocated only for
physical channels. So, fix memory corruption by ARRAY_SIZE() instead of
num_channels variable.
Note the first case is a cleanup rather than a fix as the software
timestamp channel bit in active_scanmask is never set by the IIO core.
Fixes: 9374e8f5a3 ("iio: adc: add ADC driver for the TI TSC2046 controller")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220107081401.2816357-1-o.rempel@pengutronix.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
To avoid problematic devicetree configurations. Set allocation limit
with error message and suggestion on what can be done to solve this
issue.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220117082852.3370869-2-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
sysfs_emit() is preferred over raw s*printf() for sysfs attributes since it
knows about the sysfs buffer specifics and has some built-in checks for
size and alignment.
Use sysfs_emit() to format the custom `in_power_shunt_resistor` and
`in_current_shunt_resistor` device attributes of the max9611 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20211216185217.1054495-11-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
sysfs_emit() is preferred over raw s*printf() for sysfs attributes since it
knows about the sysfs buffer specifics and has some built-in checks for
size and alignment.
Use sysfs_emit() to format the custom `in_allow_async_readout` device
attribute of the ina2xx-adc driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211216185217.1054495-7-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
sysfs_emit() is preferred over raw s*printf() for sysfs attributes since it
knows about the sysfs buffer specifics and has some built-in checks for
size and alignment.
Use sysfs_emit() to format the custom `ac_excitation` and `bridge_swtich`
attributes of the ad7192 driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211216185217.1054495-4-lars@metafoo.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Initially this was designed to:
| Fix sleeping in atomic context warning and a deadlock after iio_trigger_poll()
| call
|
| If iio_trigger_poll() is called after IRQ was disabled, we will call
| reenable_trigger() directly from hard IRQ or hrtimer context instead of
| IRQ thread. In this case we will run in to multiple issue as sleeping in atomic
| context and a deadlock.
|
| To avoid this issue, rework the trigger to use state machine. All state
| changes are done over the hrtimer, so it allows us to drop fsleep() and
| avoid the deadlock.
Since this issue was fixed by: 9020ef6598 ("iio: trigger: Fix a scheduling
whilst atomic issue seen on tsc2046"). This patch is a cleanup to make
state machine easier to follow.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20220111130402.3404769-1-o.rempel@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This commit adds mt8186 compatible node.
Signed-off-by: Guodong Liu <guodong.liu@mediatek.com>
Acked-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220110084841.575-2-guodong.liu@mediatek.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Previously inconsistent with a space after { but not before }.
Tidy that up to avoid providing an example to copy into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-14-jic23@kernel.org
Previously inconsistent with space after { but not before }.
Tidy that up to avoid providing a bad example to copy into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-13-jic23@kernel.org
Previously inconsistent with space after { and not before }.
Tidy that up to avoid providing a bad example to copy into new drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: Hui Liu <hui.liu@mediatek.com>
Reviewed-by: Gwendal Grignou <gwendal@chromium.org>
Link: https://lore.kernel.org/r/20211230174911.78291-12-jic23@kernel.org
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
find_first{,_zero}_bit is a more effective analogue of 'next' version if
start == 0. This patch replaces 'next' with 'first' where things look
trivial.
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
-----BEGIN PGP SIGNATURE-----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=xXvq
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-next
Jonathan writes:
1st set of IIO new device support, features and cleanup for 5.17
Includes some fixes that were either late breaking, low priority or
complex enough to not be good to rush in late in the cycle.
Tree rebased today to fix up some trivial issues + pull in a fix that
was previously on the fixes-togreg branch. Vast majority have been
in linux-next for some time now.
New device support
* adi,ad7293
- New driver and bindings for this Power Amplifier drain current
controller. A complex device with various related monitoring functions.
* adi,ad75513R
- New driver and bindings for this combined ADC and DAC device.
- A few follow up fixes.
* adi,admv8818
- New driver (and type) for this 2-18GHz filter device. Includes
bindings and ABI documentation to allow clk_notifier based auto
adjustment of the filters in appropriate applications.
* liteon,ltr501
- Support for the ltr303. ID and chip specific info table.
* xilinx,ams
- New generic firmware function fwnode_iomap() as used in this driver.
- New driver and bindings for this ADC and on-chip sensors as found
in various Xilinx devices.
Core
* Introduced IIO_VAL_INT_64 which uses val and val2 in IIO callbacks to
form a 64 bit integer when higher precision needed.
* Allow IIO_ENUM_AVAILABLE to be used with different shared values.
* Fix a long term issue with scheduling whilst atomic when iio_trig_poll()
is called but no trigger consumers are actually enabled and hence the
trigger may be reenabled from the interrupt handler. Seen in the wild
on the tsc2046.
* Mark iio_device_type const.
* buffer: Use a separate index variable to simplify code.
* buffer-dma: Clear out unused struct iio_buffer_block
* buffer-dmaengine: Switch to cheaper round_down() as power of 2 values.
Tests/tools
* format_value
- Check against NULL returns from allocations in tests.
- Add IIO_VAL_INT_64 test case.
* event_monitor
- Flush the output after event to given more consistent latency
when tool output piped to other programs.
Driver Features
* axp20x
- Add support for NTC thermistor channel and document TS pin binding.
* arm,scmi
- Add reading of raw channel values (using IIO_VAL_INT_64)
* liteon,ltr501
- Add proximity-near-level support and dt-binding.
Tree wide cleanup
* Remove no-op trigger ops from multiple drivers.
* Stop using dev_get_drvdata() on the iio_dev->dev in various drivers
and then stop assigning it to allow this to be used for other purposes.
We can always get to the indio_dev using dev_to_iio_dev() which is
a container_of() based approach. Also cleanup up some related unnecessary
convoluted cases.
- atmel,at91-sam5d2
- nxp,imx7d
- meas,ms5611
- st,st_sensors
* Where available (or easy to introduce) use the scan_type.* values
in place of a second copy for read_raw and similar paths.
- adi,ad7266
- bosch,bma220
- fsl,mac3110
- fsl,mma7455
- fsl,mpl3115
- kionix,kcjk-1013
- sensortek,stk8ba50
- sensortek,stk8312
- ti,adc12138
- ti,ads1015
- vti,sca3000
- xilinx,xadc-core
* Switch drives over to generic firmware properties including appropriate
header changes to avoid including of.h
- Various DACs had false CONFIG_OF dependencies.
- dpot-dac
- envelope-detector
- adi,ad5755
- adi,ad5758
- capella,cm3605
- maxim,max9611
- microchip,mcp41010
- microchip,mcp3911
- ti,adc12138
* Trivial clang warning fixes for W=1 warnings.
Driver specific cleanup and minor fixes
* adi,ad7606
- Comment fixes.
* ams,ad3935
- Drop pointless cast to the same type.
* atmel,at91-sama5d2
- Fix wrong cast of iio_dev->dev to platform_device that happened to
be harmless.
* fsl,mma7660
- Stop i2c remove() function returning an error code. Part of a rework
to eventually stop returning anything from these.
* fsl,mma8452
- Use correct type for local irqreturn_t.
* nxp,imx8mq
- Maintainer email address update.
* nxp,lpc18xx_adc
- Ensure clk_prepare_enable() called before clk_get_rate().
- Switch of.h for mod_devicetable.h to reflect no of specific functions,
just the id table.
* renesas,rzg2l
- Drop a dev_err() that just duplicates error printed in platform_get_irq()
* sgx,vz89x
- Drop pointless cast.
* st,lsm6dsx
- Make it possible to disable the sensorhub from DT to avoid a corner
case where the address of a slave device many be accidentally modified.
* st,stm32-adc
- Stop leaking an of_node in an error path.
* st,stmp2
- Avoid wrong sized type for bit field which could result in
over-reading (harmless). Precursor to enabling -Warray-bounds.
* ti,adc081c
- Put back some ACPI support for non standards compliant ADC081C
ID because it is known to be in the wild on some Aaeon boards.
* ti,ads8688
- Cleanup redundant local ret variable assignment.
* ti,ina2xx-adc
- Use helper macro kthread_run() to replace some boilerplate.
- Avoid double reference counting.
- Drop pointless cast.
* xilinx,xadc
- Make the IRQ optional as not always wired to the host system.
* tag 'iio-for-5.17a' of https://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (103 commits)
iio: adc: ti-adc081c: Partial revert of removal of ACPI IDs
iio:addac:ad74413r: Fix uninitialized ret in a path that won't be hit.
MAINTAINERS: Add maintainer for xilinx-ams
dt-bindings: iio: adc: Add Xilinx AMS binding documentation
iio: adc: Add Xilinx AMS driver
device property: Add fwnode_iomap()
iio:accel:kxcjk-1013: Mark struct __maybe_unused to avoid warning.
iio:accel:bmc150: Mark structure __maybe_unused as only needed with for pm ops.
iio:dummy: Drop set but unused variable len.
iio:magn:ak8975: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_mpu6050: Suppress clang W=1 warning about pointer to enum conversion.
iio:imu:inv_icm42600: Suppress clang W=1 warning about pointer to enum conversion.
iio:dac:mcp4725: Suppress clang W=1 warning about pointer to enum conversion.
iio:amplifiers:hmc425a: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ti-ads1015: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:rcar: Suppress clang W=1 warning about pointer to enum conversion.
iio:adc:ina2xx-adc: Suppress clang W=1 warning about pointer to enum conversion.
iio:accel:bma180: Suppress clang W=1 warning about pointer to enum conversion.
drivers:iio:dac: Add AD3552R driver support
dt-bindings: iio: dac: Add adi,ad3552r.yaml
...
Unfortuanately a non standards compliant ACPI ID is known to be
in the wild on some AAEON boards.
Partly revert the removal of these IDs so that ADC081C will again
work + add a comment to that affect for future reference.
Whilst here use generic firmware properties rather than the ACPI
specific handling previously found in this driver.
Reported-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw>
Fixes: c458b7ca3f ("iio:adc:ti-adc081c: Drop ACPI ids that seem very unlikely to be official.")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Tested-by: Kunyang Fan <Kunyang_Fan@aaeon.com.tw> #UP-extremei11
Link: https://lore.kernel.org/r/20211205172728.2826512-1-jic23@kernel.org
Cc: <Stable@vger.kernel.org>
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such
as temperature and supply voltage levels. The AMS has two SYSMON blocks.
PL-SYSMON block is capable of monitoring off chip voltage and
temperature.
PL-SYSMON block has DRP, JTAG and I2C interface to enable monitoring
from an external master. Out of these interfaces currently only DRP is
supported. Other block PS-SYSMON is memory mapped to PS.
The AMS can use internal channels to monitor voltage and temperature as
well as one primary and up to 16 auxiliary channels for measuring
external voltages.
The voltage and temperature monitoring channels also have event capability
which allows to generate an interrupt when their value falls below or
raises above a set threshold.
Co-developed-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Anand Ashok Dumbre <anand.ashok.dumbre@xilinx.com>
Link: https://lore.kernel.org/r/20211203212358.31444-4-anand.ashok.dumbre@xilinx.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
`buf` is cast to a const char *, but `buf` is already a const char *, so
the case is unnecessary.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The find.h APIs are designed to be used only on unsigned long arguments.
This can technically result in a over-read, but it is harmless in this
case. Regardless, fix it to avoid the warning seen under -Warray-bounds,
which we'd like to enable globally:
In file included from ./include/linux/bitmap.h:9,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/cpumask.h:5,
from ./arch/x86/include/asm/msr.h:11,
from ./arch/x86/include/asm/processor.h:22,
from ./arch/x86/include/asm/cpufeature.h:5,
from ./arch/x86/include/asm/thread_info.h:53,
from ./include/linux/thread_info.h:60,
from ./arch/x86/include/asm/preempt.h:7,
from ./include/linux/preempt.h:78,
from ./include/linux/spinlock.h:55,
from ./include/linux/swait.h:7,
from ./include/linux/completion.h:12,
from drivers/iio/adc/stmpe-adc.c:10:
drivers/iio/adc/stmpe-adc.c: In function 'stmpe_adc_probe':
./include/linux/find.h:98:23: warning: array subscript 'long unsigned int[0]' is partly outside array bounds of 'u32[1]' {aka 'unsigned int[1]'} [-Warray-bounds]
98 | val = *addr | ~GENMASK(size - 1, offset);
| ^~~~~
drivers/iio/adc/stmpe-adc.c:258:13: note: while referencing 'norequest_mask'
258 | u32 norequest_mask = 0;
| ^~~~~~~~~~~~~~
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Return value from ads8688_prog_write() directly instead
of taking this in another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
We could probably drop a lot more of these, but for now this removes
unnecessary restrictions on stand alone ADC devices.
For these 3 drivers the false dependency seems to date all
the way back to their initial introduction.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Nothing in this driver depends on OF firmware so drop the dependency
and update the headers to remove the false impression such a dependency
exists.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
There is nothing directly using of specific interfaces in this driver,
so lets not include the headers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This enables using the driver with other firmware types such
as ACPI via PRP0001.
Also part of a general attempt to move IIO drivers over to generic
properties to avoid opportunities for cut and paste.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This allows use of the driver with other types of firmware such as ACPI
PRP0001 based probing.
Also part of a general attempt to remove direct use of of_ specific
accessors from IIO.
Added an include for mod_devicetable.h whilst here to cover the
struct of_device_id definition.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Kent Gustavsson <kent@minoris.se>
Reviewed-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Note the handling of the device tree node in this driver was somewhat
unusual. I have cleaned that up whilst also moving over to generic
properties.
Part of a general attempt to move all IIO drivers over to generic
firmware properties both as a general improvement and to avoid sources
of cut and paste into future drivers.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Most AXPxxx-based reference designs place a 10k NTC thermistor on a
TS pin. When appropriately configured, AXP PMICs will inject fixed
current (80uA by default) into TS pin and measure the voltage across a
thermistor. The PMIC itself will by default compare this voltage with
predefined thresholds and disable battery charging whenever
the battery is too hot or too cold.
Alternatively, the TS pin can be configured as general-purpose
ADC input. This mode is not supported by the driver.
This patch allows reading the voltage on the TS pin. It can be then
either processed by userspace or used by kernel consumer like hwmon
ntc thermistor driver.
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Quentin Schulz <foss+kernel@0leil.net>
Link: https://lore.kernel.org/r/20211118141233.247907-2-boger@wirenboard.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The shared parameter should be configurable based on its usage, and not
constrained to IIO_SHARED_BY_TYPE.
This patch aims to improve the flexibility in using the
IIO_ENUM_AVAILABLE define and avoid redefining custom iio enums that
expose the shared parameter.
An example is the ad5766.c driver where IIO_ENUM_AVAILABLE_SHARED was
defined in order to achieve `shared` parameter customization.
The current state of the IIO_ENUM_AVAILABLE implementation will imply
similar redefinitions each time a driver will require access to the
`shared` parameter. An example would be admv1013 driver which will
require custom device attribute for the frequency translation modes:
Quadrature I/Q mode and Intermediate Frequency mode.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Reviewed-by: Alexandru Ardelean <ardeleanalex@gmail.com>
Link: https://lore.kernel.org/r/20211119085627.6348-1-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
dev_err_probe() calls __device_set_deferred_probe_reason()
on -EPROBE_DEFER error. If device pointer to driver core
private structure is not initialized, an null pointer error occurs.
This pointer is set on iio_device_register() call for iio device.
dev_err_probe() must be called with the device which is probing.
Replace iio device by its parent device.
Fixes: 0e346b2cfa ("iio: adc: stm32-adc: add vrefint calibration support")
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/20211122143809.2332-1-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Use scan_type when processing raw data which also fixes that the sign
extension was from the wrong bit.
Use channel definition as root of trust and replace constant
when reading elements directly using the raw sysfs attributes.
Fixes: 6794e23fa3 ("iio: adc: at91-sama5d2_adc: add support for oversampling resolution")
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Eugen Hristev <eugen.hristev@microchip.com>
Cc: <Stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211104082413.3681212-9-gwendal@chromium.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Both the charging and discharging currents on AXP22x are stored as
12-bit integers, in accordance with the datasheet.
It's also confirmed by vendor BSP (axp20x_adc.c:axp22_icharge_to_mA).
The scale factor of 0.5 is never mentioned in datasheet, nor in the
vendor source code. I think it was here to compensate for
erroneous addition bit in register width.
Tested on custom A40i+AXP221s board with external ammeter as
a reference.
Fixes: 0e34d5de96 ("iio: adc: add support for X-Powers AXP20X and AXP22X PMICs ADCs")
Signed-off-by: Evgeny Boger <boger@wirenboard.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Link: https://lore.kernel.org/r/20211116213746.264378-1-boger@wirenboard.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
IIO trigger handlers must call iio_trigger_notify_done() when done. This
must be done even when an error occurred. Otherwise the trigger will be
seen as busy indefinitely and the trigger handler will never be called
again.
The ad7768-1 driver neglects to call iio_trigger_notify_done() when there
is an error reading the converter data. Fix this by making sure that
iio_trigger_notify_done() is included in the error exit path.
Fixes: a5f8c7da3d ("iio: adc: Add AD7768-1 ADC basic support")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Link: https://lore.kernel.org/r/20211101144055.13858-2-lars@metafoo.de
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Uwe Kleine-König