The clk count has been get with of_clk_get_parent_count, there is
no need to pass clk_count from users.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20230104110032.1220721-4-peng.fan@oss.nxp.com
The imx_obtain_fixed_clk_hw name was wrong and misleading. Renaming it
to imx_get_clk_hw_by_name clarifies the purpose of the function, and
will allow it to be used not only for fixed rate clocks but also in
wider contexts.
No functional changes intended.
The replacements were made with the following command:
grep -rl 'imx_obtain_fixed_clk_hw' ./ | \
xargs sed -i 's/imx_obtain_fixed_clk_hw/imx_get_clk_hw_by_name/g'
Tested on a BSH SystemMaster (SMM) S2 board.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Abel Vesa <abel.vesa@linaro.org>
Link: https://lore.kernel.org/r/20221113180839.1625832-1-dario.binacchi@amarulasolutions.com
The SNVS moudule is not used only by the linux, it may also used
by other SW component is secure world. No sense to populate it
in linux, so remove it.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220310093404.236966-1-ping.bai@nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Add mcore_booted boot parameter which could simplify AMP clock
management. To i.MX8M, there is CCM(clock control Module) to generate
clock root clock, anatop(analog PLL module) to generate PLL, and CCGR
(clock gating) to gate clocks to peripherals. As below:
anatop->ccm->ccgr->peripheral
Linux handles the clock management and the auxiliary core is under
control of Linux. Although there is per hardware domain control for CCGR
and CCM, auxiliary core normally only use CCGR hardware domain control
to avoid linux gate off the clk to peripherals and leave CCM ana anatop
to Linux.
Per NXP hardware design, because CCGR already support gate to
peripherals, and clk root gate power leakage is negligible. So
when in AMP case, we could not register the clk root gate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220228124112.3974242-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
According to pll documentation, the 3rd pll ref clock should be
hdmi phy 27m clock, not dummy clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220225090002.2497057-3-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
On the i.MX8M*, the TF-A exposes a SiP (Silicon Provider) service
for DDR frequency scaling. The imx8m-ddrc-devfreq driver calls the
SiP and then does clk_set_parent on the DDR muxes to synchronize
the clock tree.
Since 936c383673 ("clk: imx: fix composite peripheral flags"),
these TF-A managed muxes have SET_PARENT_GATE set, which results
in imx8m-ddrc-devfreq's clk_set_parent after SiP failing with -EBUSY:
echo 25000000 > userspace/set_freq
imx8m-ddrc-devfreq 3d400000.memory-controller: failed to set
dram_apb parent: -16
Fix this by adding a new i.MX composite flag for firmware managed
clocks, which clears SET_PARENT_GATE.
This is safe to do, because updating the Linux clock tree to reflect
reality will always be glitch-free.
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20210810151432.9228-1-a.fatoum@pengutronix.de
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Remove the PLL clock gates as the allowing to gate the sys1_pll_266m breaks
the uSDHC module which is sporadically unable to enumerate devices after
this change. Also it makes AMP clock management harder with no obvious
benefit to Linux, so just revert the change.
Link: https://lore.kernel.org/r/20210528180135.1640876-1-l.stach@pengutronix.de
Fixes: b04383b6a5 ("clk: imx8mq: Define gates for pll1/2 fixed dividers")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
- The sys2_pll_50m should be one of the clock sels of PCIE_AUX clock.
Change the sys2_pll_500m to sys2_pll_50m.
- Correct one misspell of the imx8mq_pcie1_ctrl_sels definition, from
"sys2_pll_250m" to "sys2_pll_333m".
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
The PLL monitor is mentioned as a debug feature in the reference manual,
but there are some boards that use this clock output as a reference clock
for board level components. Add support for those clocks in the clock
driver, so this clock output can be used properly.
Note that the VIDEO1, GPU and VPU mux inputs are rotated compared to the
description in the reference manual. The order in this patch has been
empirically validated.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
ability to get struct clk pointers from a struct clk_hw so that clk providers
can consume the clks they provide, if they need to do something like that. This
has been a long missing part of the clk provider API that will help us move
away from exposing a struct clk pointer in the struct clk_hw. Tracepoints are
added for the clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to help
developers understand the hardware enable state of clks in case firmware or
bootloader state is different than what is expected. Overall the core changes
are mostly improving the clk driver writing experience.
At the driver level, we have the usual collection of driver updates and new
drivers for new SoCs. This time around the Qualcomm folks introduced a good
handful of clk drivers for various parts of three or four SoCs. The SiFive
folks added a new clk driver for their FU740 SoCs, coming in second on the
diffstat and then Atmel AT91 and Amlogic SoCs had lots of work done after that
for various new features. One last thing to note in the driver area is that the
i.MX driver has gained a new binding to support SCU clks after being on the
list for many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and tweaks that
come from more testing and finding out that some configuration was wrong or
that a driver could support being built as a module.
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks
-----BEGIN PGP SIGNATURE-----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=Wt9O
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mq.c:626:34: warning:
‘imx8mq_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673 ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to the latest RM (see Table 5-1. Clock Root Table),
both usdhc root clocks have the parent order as follows:
000 - 25M_REF_CLK
001 - SYSTEM_PLL1_DIV2
010 - SYSTEM_PLL1_CLK
011 - SYSTEM_PLL2_DIV2
100 - SYSTEM_PLL3_CLK
101 - SYSTEM_PLL1_DIV3
110 - AUDIO_PLL2_CLK
111 - SYSTEM_PLL1_DIV8
So the audio_pll2_out and sys3_pll_out have to be swapped.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Cosmin Stefan Stoica <cosmin.stoica@nxp.com>
Link: https://lore.kernel.org/r/1602753944-30757-1-git-send-email-abel.vesa@nxp.com
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Change configuration to "tristate", add module author, description
and license to support building i.MX8M SoCs clock driver as module.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the bus clk use imx8m_clk_hw_composite_bus, then
we could avoid possible issue when setting mux of the clk.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Migrate A53 clk root to use composite core clk type. It
will simplify code and make it easy to use composite
specific mux operation.
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The parent settings have been moved to dtsi, we no need to
set parent here. And clk_hw_set_parent will trigger lockdep warning,
because this api not have prepare_lock.
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
'A53_CORE' is just a mux and no need to be critical, being critical
will cause its parent clock always ON which does NOT make sense,
to make sure CPU's hardware clock source NOT being disabled during
clock tree setup, need to move the 'A53_SRC'/'A53_CORE' reparent
operations to after critical clock 'ARM_CLK' setup finished.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The A53 CCM clk root only accepts input up to 1GHz, CCM A53 root
signoff timing is 1Ghz, however the A53 core which sources from CCM
root could run above 1GHz which violates the CCM.
There is a CORE_SEL slice before A53 core, we need to configure the
CORE_SEL slice source from ARM PLL, not A53 CCM clk root.
The A53 CCM clk root should only be used when need to change ARM PLL
frequency.
Add arm_a53_core clk that could source from arm_a53_div and arm_pll_out.
Configure a53 ccm root sources from 800MHz sys pll
Configure a53 core sources from arm_pll_out
Mark arm_a53_core as critical clock
Fixes: db27e40b27 ("clk: imx8mq: Add the missing ARM clock")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After finishing using device node got from of_find_compatible_node(),
of_node_put() needs to be called.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX8M SoCs clock driver are provider, NOT consumer, so clk-provider.h
should be used instead of clk.h.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use imx8m_clk_hw_composite_core to simplify code.
Add new definitions, and X_SRC/CG/DIV will be alias to the new
definitions for backwards compatibility
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Switch the entire clk-imx8mq driver to clk_hw based API.
This allows us to move closer to a clear split between
consumer and provider clk APIs.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the manual the acronym stands for
Spread Sprectum Clock Generator.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clock drivers on imx8m series are registered as platform devices and
this opens the possibility of reloading the driver at runtime.
This doesn't actually work: clocks are never removed and attempting to
bind again results in registration errors and a crash. Almost all
devices depend on clocks anyway so rebinding is unlikely to ever be
useful
Fix this by explicitly suppressing bind attrs like several other
clock drivers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
These clocks are only modified as part of DRAM frequency switches during
which DRAM itself is briefly inaccessible. The switch is performed with
a SMC call to by TF-A which runs from a SRAM area; upon returning to
linux several clocks bits are modified and we need to update them.
For rate bits an easy solution is to just mark with
CLK_GET_RATE_NOCACHE so that new rates are always read back from
registers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is not correct that sys3_pll_out use sys2_pll1_ref_sel as parent.
According to the current imx_clk_sccg_pll design, it uses both
bypass1/2, however set bypass2 as 1 is not correct, because it will
make sys[x]_pll_out use wrong parent and might access wrong registers.
So correct bypass2 to 0 and fix sys3_pll_out_sels.
Fixes: e9dda4af68 ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According Architecture definition guide, SYS1_PLL is fixed at
800MHz, SYS2_PLL is fixed at 1000MHz, so let's use imx_clk_fixed
to register the clocks and drop code that could change the rate.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On imx8mq there are 9 fixed-factor dividers for SYS_PLL1 and SYS_PLL2
each with their own gate but these gates are not currently defined in
the clock tree.
Add them between sys1/2_pll_out and the fixed dividers.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This clock is needed by DCSS when high resolutions are used.
Signed-off-by: Laurentiu Palcu <laurentiu.palcu@nxp.com>
CC: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The "sys3_pll2_out" CLK was removed in refactoring so all references
need to be updated to "sys3_pll_out"
Fixes: e9dda4af68 ("clk: imx: Refactor entire sccg pll clk")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When of_clk_add_provider failed, all clks should be unregistered.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Initially, the TMU_ROOT clock was marked as critical, which automatically
made the AHB clock to stay always on. Since the TMU_ROOT clock is not
marked as critical anymore, following commit:
"clk: imx8mq: Remove CLK_IS_CRITICAL flag for IMX8MQ_CLK_TMU_ROOT"
all the clocks that derive from ipg_root clock (and implicitly ahb clock)
would also have to enable, along with their own gate, the AHB clock.
But considering that AHB is actually a bus that has to be always on, we mark
it as critical in the clock provider driver and then all the clocks that
derive from it can be controlled through the dedicated per IP gate which
follows after the ipg_root clock.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Per latest imx8mq datasheet of CCM, the parent of usb1_ctrl_root_clk
and usb2_ctrl_root_clk is usb_bus.
Signed-off-by: Li Jun <jun.li@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
IMX8MQ_CLK_TMU_ROOT is ONLY used for thermal module, the driver
should manage this clock, so no need to have CLK_IS_CRITICAL flag
set.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Call imx_register_uart_clocks() API to keep uart clocks enabled
when earlyprintk or earlycon is active.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is documented in the reference manuals as GIC_CLK_ROOT.
In some out-of-tree DVFS scenarios the gic clock can end up as the only
user of sys_pll2 so if we don't define the gic clk explicitly it might
be turned off.
This applies to both 8mq and 8mm: same clk register but diffferent
parents.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX8MQ has clock gate for SNVS module, add it into clock tree
for SNVS RTC driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It's defined in imx8mq-clock.h but wasn't assigned yet. It's used as
clk_tx_esc in the nwl dsi host controller (i.MX8MQ RM, Rev. 0, 01/2018
Sect. 13.5.3.7.4).
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
i.MX8MQ has clock gate for each GPIO bank, add them
into clock tree for GPIO driver to manage.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Make the entire combination of plls to be one single clock. The parents used
for bypasses are specified each as an index in the parents list.
The determine_rate does a lookup throughout all the possible combinations
for all the divs and returns the best possible 'setup' which in turn is used
by set_rate later to set up all the divs and bypasses.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the ARM clock as imx_clk_cpu type.
Will be used by cpufreq.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arm pll bypass needs to propagate the rate upwards
in order for the cpufreq to work.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Add the entry for the CLKO1 clock.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The CLKO2 clock source select list is the following as per the i.MX8M
Reference Manual:
000 - 25M_REF_CLK
001 - SYSTEM_PLL2_DIV5
010 - SYSTEM_PLL1_DIV2
011 - SYSTEM_PLL2_DIV6
100 - SYSTEM_PLL3_CLK
101 - AUDIO_PLL1_CLK
110 - VIDEO_PLL1_CLK
111 - 32K_REF_CLK
However, in imx8mq_clko2_sels[] only the first four entries are correct.
Fix it by adding the missing "sys3_pll2_out" entry in order to match
the description from the manual.
Fixes: b80522040c ("clk: imx: Add clock driver for i.MX8MQ CCM")
Reported-by: Rogerio Pimentel <rogerio.silva@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clocks list is missing the clocks for the M4 core.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The arrays containing the mux selectors need to be of const pointer
to const char.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>