Commit Graph

140 Commits

Author SHA1 Message Date
Matthias Kaehlcke ad571d725c Bluetooth: hci_qca: Move boot delay to qca_send_power_pulse()
After sending a power on pulse the driver has a delay of 100ms
to allow the host controller to boot. Move the delay into
qca_send_power_pulse(), since it is directly related with the
power-on pulse.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27 08:44:32 +01:00
Matthias Kaehlcke 9836b80208 Bluetooth: hci_qca: Pass boolean 'on/off' to qca_send_power_pulse()
There are only two types of power pulses 'on' or 'off', pass a boolean
instead of the power pulse 'command'.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-27 08:44:32 +01:00
Matthias Kaehlcke 5971752de4 Bluetooth: hci_qca: Set HCI_QUIRK_USE_BDADDR_PROPERTY for wcn3990
Set quirk for wcn3990 to read BD_ADDR from a firmware node property.

Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-26 10:08:26 +01:00
Balakrishna Godavarthi 035a960e7a Bluetooth: hci_qca: Disable IBS state machine and flush Tx buffer
During hci down we observed IBS sleep commands are queued in the Tx
buffer and hci_uart_write_work is sending data to the chip which is
not required as the chip is powered off. This patch will disable IBS
and flush the Tx buffer before we turn off the chip.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-18 11:49:53 +01:00
Balakrishna Godavarthi 78e8fa2972 Bluetooth: hci_qca: Deassert RTS while baudrate change command
This patch will help to stop frame reassembly errors while changing
the baudrate. This is because host send a change baudrate request
command to the chip with 115200 bps, Whereas chip will change their
UART clocks to the enable for new baudrate and sends the response
for the change request command with newer baudrate, On host side
we are still operating in 115200 bps which results of reading garbage
data. Here we are pulling RTS line, so that chip we will wait to send data
to host until host change its baudrate.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-18 11:49:41 +01:00
Balakrishna Godavarthi f9558270b8 Bluetooth: hci_qca: use wait_until_sent() for power pulses
wcn3990 requires a power pulse to turn ON/OFF along with
regulators. Sometimes we are observing the power pulses are sent
out with some time delay, due to queuing these commands. This is
causing synchronization issues with chip, which intern delay the
chip setup or may end up with communication issues.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-02-18 11:49:40 +01:00
Balakrishna Godavarthi 5c0a1001c8 Bluetooth: hci_qca: Add helper to set device address
This patch add qca_set_bdaddr() to set the device
address for latest Qualcomm Bluetooth chipset wcn3990 and above.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-01-22 09:51:18 +01:00
Balakrishna Godavarthi c614ca3f74 Bluetooth: hci_qca: Add support for controller debug logs.
This patch will prevent error messages splashing on console.

[   78.426697] Bluetooth: hci_core.c:hci_acldata_packet() hci0: ACL packet for unknown connection handle 3804
[   78.436682] Bluetooth: hci_core.c:hci_acldata_packet() hci0: ACL packet for unknown connection handle 3804
[   78.446639] Bluetooth: hci_core.c:hci_acldata_packet() hci0: ACL packet for unknown connection handle 3804
[   78.456596] Bluetooth: hci_core.c:hci_acldata_packet() hci0: ACL packet for unknown connection handle 3804

QCA wcn3990 will send the debug logs in the form of ACL packets.
While decoding packet in qca_recv(), marking the received debug log
packet as diagnostic packet.

Signed-off-by: Harish Bandi <c-hbandi@codeaurora.org>
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-10-18 09:55:16 +02:00
David S. Miller d864991b22 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net
Conflicts were easy to resolve using immediate context mostly,
except the cls_u32.c one where I simply too the entire HEAD
chunk.

Signed-off-by: David S. Miller <davem@davemloft.net>
2018-10-12 21:38:46 -07:00
Kees Cook 329e098939 treewide: Replace more open-coded allocation size multiplications
As done treewide earlier, this catches several more open-coded
allocation size calculations that were added to the kernel during the
merge window. This performs the following mechanical transformations
using Coccinelle:

	kvmalloc(a * b, ...) -> kvmalloc_array(a, b, ...)
	kvzalloc(a * b, ...) -> kvcalloc(a, b, ...)
	devm_kzalloc(..., a * b, ...) -> devm_kcalloc(..., a, b, ...)

Signed-off-by: Kees Cook <keescook@chromium.org>
2018-10-05 18:06:30 -07:00
Balakrishna Godavarthi 3e4be65eb8 Bluetooth: hci_qca: Add poweroff support during hci down for wcn3990
This patch enables power off support for hci down and power on support
for hci up. As wcn3990 power sources are ignited by regulators, we will
turn off them during hci down, i.e. an complete power off of wcn3990.
So while hci up, will call vendor setup which will turn on the regulators,
requests BT chip version and download the firmware.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 12:30:07 +02:00
Balakrishna Godavarthi c2d7827338 Bluetooth: hci_qca: Remove hdev dereference in qca_close().
When flag KASAN is set, we are seeing an following crash while removing
hci_uart module.

[   50.589909] Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b73
[   50.597902] Mem abort info:
[   50.600846]   Exception class = DABT (current EL), IL = 32 bits
[   50.606959]   SET = 0, FnV = 0
[   50.610142]   EA = 0, S1PTW = 0
[   50.613396] Data abort info:
[   50.616401]   ISV = 0, ISS = 0x00000004
[   50.620373]   CM = 0, WnR = 0
[   50.623466] [006b6b6b6b6b6b73] address between user and kernel address ranges
[   50.630818] Internal error: Oops: 96000004 [#1] PREEMPT SMP

[   50.671670] PC is at qca_power_shutdown+0x28/0x100 [hci_uart]
[   50.677593] LR is at qca_close+0x74/0xb0 [hci_uart]
[   50.775689] Process rmmod (pid: 2144, stack limit = 0xffffff801ba90000)
[   50.782493] Call trace:

[   50.872150] [<ffffff8000c3c81c>] qca_power_shutdown+0x28/0x100 [hci_uart]
[   50.879138] [<ffffff8000c3c968>] qca_close+0x74/0xb0 [hci_uart]
[   50.885238] [<ffffff8000c3a71c>] hci_uart_unregister_device+0x44/0x50 [hci_uart]
[   50.892846] [<ffffff8000c3c9f4>] qca_serdev_remove+0x50/0x5c [hci_uart]
[   50.899654] [<ffffff800844f630>] serdev_drv_remove+0x28/0x38
[   50.905489] [<ffffff800850fc44>] device_release_driver_internal+0x140/0x1e4
[   50.912653] [<ffffff800850fd94>] driver_detach+0x78/0x84
[   50.918121] [<ffffff800850edac>] bus_remove_driver+0x80/0xa8
[   50.923942] [<ffffff80085107dc>] driver_unregister+0x4c/0x58
[   50.929768] [<ffffff8000c3ca8c>] qca_deinit+0x24/0x598 [hci_uart]
[   50.936045] [<ffffff8000c3ca10>] hci_uart_exit+0x10/0x48 [hci_uart]
[   50.942495] [<ffffff8008136630>] SyS_delete_module+0x17c/0x224

This crash is due to dereference of hdev, after freeing it.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 11:59:58 +02:00
Balakrishna Godavarthi ca30ccd219 Bluetooth: hci_qca: Remove serdev_device_open/close function calls
Removed serdev_device_open/close functions from qca_open/close as
they are called in hci_uart_register_device() and
hci_uart_unregister_device() functions.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27 11:59:58 +02:00
Balakrishna Godavarthi fa9ad876b8 Bluetooth: hci_qca: Add support for Qualcomm Bluetooth chip wcn3990
Add support to set voltage/current of various regulators
to power up/down Bluetooth chip wcn3990.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-03 14:44:07 +02:00
Balakrishna Godavarthi be93a497fa Bluetooth: hci_qca: Enable 3.2 Mbps operating speed.
Enable Qualcomm chips to operate at 3.2Mbps.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-03 14:44:07 +02:00
Balakrishna Godavarthi 83d9c5e566 Bluetooth: hci_qca: Add wrapper functions for setting UART speed
In function qca_setup, we set initial and operating speeds for Qualcomm
Bluetooth SoC's. This block of code is common across different
Qualcomm Bluetooth SoC's. Instead of duplicating the code, created
a wrapper function to set the speeds. So that future coming SoC's
can use these wrapper functions to set speeds.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-03 14:44:07 +02:00
Balakrishna Godavarthi aadebac463 Bluetooth: btqca: Redefine qca_uart_setup() to generic function.
Redefinition of qca_uart_setup will help future Qualcomm Bluetooth
SoC, to use the same function instead of duplicating the function.
Added new arguments soc_type and soc_ver to the functions.

These arguments will help to decide type of firmware files
to be loaded into Bluetooth chip.
soc_type holds the Bluetooth chip connected to APPS processor.
soc_ver holds the Bluetooth chip version.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-03 14:44:06 +02:00
Balakrishna Godavarthi ba493d4fbc Bluetooth: btqca: Rename ROME specific functions to generic functions
Some of the QCA BTSoC ROME functions, are used for different versions
or different make of BTSoC's. Instead of duplicating the same functions
for new chip, update names of the functions that are used for both
chips to keep this generic and would help in future when we would have
new BT SoC. To have generic text in logs updated from ROME to QCA where
ever possible. This avoids confusion to user, when using the future
Qualcomm Bluetooth SoC's. Updated BT_DBG, BT_ERR and BT_INFO with
bt_dev_dbg, bt_dev_err and bt_dev_info where ever applicable.

Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-03 14:44:06 +02:00
Jia-Ju Bai 25a13e382d bluetooth: hci_qca: Replace GFP_ATOMIC with GFP_KERNEL
qca_open() and qca_set_baudrate() are never called in atomic context.

They call kzalloc() and bt_skb_alloc() with GFP_ATOMIC,
which is not necessary.
GFP_ATOMIC can be replaced with GFP_KERNEL.

This is found by a static analysis tool named DCNS written by myself.
I also manually check the kernel code before reporting it.

Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-23 18:05:01 +02:00
Thierry Escande 9960521c44 Bluetooth: hci_qca: Fix "Sleep inside atomic section" warning
This patch fixes the following warning during boot:

 do not call blocking ops when !TASK_RUNNING; state=1 set at
 [<(ptrval)>] qca_setup+0x194/0x750 [hci_uart]
 WARNING: CPU: 2 PID: 1878 at kernel/sched/core.c:6135
 __might_sleep+0x7c/0x88

In qca_set_baudrate(), the current task state is set to
TASK_UNINTERRUPTIBLE before going to sleep for 300ms. It was then
restored to TASK_INTERRUPTIBLE. This patch sets the current task state
back to TASK_RUNNING instead.

Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-30 08:12:17 +02:00
Thierry Escande 05ba533c5c Bluetooth: hci_qca: Add serdev support
Add support for Qualcomm serial slave devices. Probe the serial device,
retrieve its maximum speed and register a new hci uart device.

Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18 06:37:51 +02:00
Amit Pundir 7dc5fe0814 Bluetooth: hci_qca: Avoid missing rampatch failure with userspace fw loader
AOSP use userspace firmware loader to load firmwares, which will
return -EAGAIN in case qca/rampatch_00440302.bin is not found.
Since there is no rampatch for dragonboard820c QCA controller
revision, just make it work as is.

CC: Loic Poulain <loic.poulain@linaro.org>
CC: Nicolas Dechesne <nicolas.dechesne@linaro.org>
CC: Marcel Holtmann <marcel@holtmann.org>
CC: Johan Hedberg <johan.hedberg@gmail.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-05-18 06:37:50 +02:00
Loic Poulain ba8f359790 Bluetooth: hci_qca: Avoid setup failure on missing rampatch
Assuming that the original code idea was to enable in-band sleeping
only if the setup_rome method returns succes and run in 'standard'
mode otherwise, we should not return setup_rome return value which
makes qca_setup fail if no rampatch/nvm file found.

This fixes BT issue on the dragonboard-820C p4 which includes the
following QCA controller:
hci0: Product:0x00000008
hci0: Patch  :0x00000111
hci0: ROM    :0x00000302
hci0: SOC    :0x00000044

Since there is no rampatch for this controller revision, just make
it work as is.

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-12-13 00:28:40 +01:00
Marcel Holtmann 2064ee332e Bluetooth: Use bt_dev_err and bt_dev_info when possible
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and
bt_dev_info when possible. This allows for controller specific
reporting.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-30 12:25:45 +02:00
Kees Cook 0435605289 Bluetooth: Convert timers to use timer_setup()
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly. As already done in hci_qca, add
struct hci_uart pointer to priv structure.

Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-10-06 20:37:11 +02:00
Johannes Berg 634fef6107 networking: add and use skb_put_u8()
Joe and Bjørn suggested that it'd be nicer to not have the
cast in the fairly common case of doing
	*(u8 *)skb_put(skb, 1) = c;

Add skb_put_u8() for this case, and use it across the code,
using the following spatch:

    @@
    expression SKB, C, S;
    typedef u8;
    identifier fn = {skb_put};
    fresh identifier fn2 = fn ## "_u8";
    @@
    - *(u8 *)fn(SKB, S) = C;
    + fn2(SKB, C);

Note that due to the "S", the spatch isn't perfect, it should
have checked that S is 1, but there's also places that use a
sizeof expression like sizeof(var) or sizeof(u8) etc. Turns
out that nobody ever did something like
	*(u8 *)skb_put(skb, 2) = c;

which would be wrong anyway since the second byte wouldn't be
initialized.

Suggested-by: Joe Perches <joe@perches.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16 11:48:40 -04:00
Johannes Berg 4df864c1d9 networking: make skb_put & friends return void pointers
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_put, __skb_put };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_put, __skb_put };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

which actually doesn't cover pskb_put since there are only three
users overall.

A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16 11:48:39 -04:00
Johannes Berg 59ae1d127a networking: introduce and use skb_put_data()
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.

An spatch similar to the one for skb_put_zero() converts many
of the places using it:

    @@
    identifier p, p2;
    expression len, skb, data;
    type t, t2;
    @@
    (
    -p = skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    |
    -p = (t)skb_put(skb, len);
    +p = skb_put_data(skb, data, len);
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, len);
    |
    -memcpy(p, data, len);
    )

    @@
    type t, t2;
    identifier p, p2;
    expression skb, data;
    @@
    t *p;
    ...
    (
    -p = skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    |
    -p = (t *)skb_put(skb, sizeof(t));
    +p = skb_put_data(skb, data, sizeof(t));
    )
    (
    p2 = (t2)p;
    -memcpy(p2, data, sizeof(*p));
    |
    -memcpy(p, data, sizeof(*p));
    )

    @@
    expression skb, len, data;
    @@
    -memcpy(skb_put(skb, len), data, len);
    +skb_put_data(skb, data, len);

(again, manually post-processed to retain some comments)

Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-16 11:48:37 -04:00
Colin Ian King e059a465cc Bluetooth: hci_qca: fix spelling mistake: "Spurrious" -> "Spurious"
trivial fix to spelling mistake in error message

Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-02-18 20:09:47 +01:00
Prasanna Karthik 1ae6d00ad0 Bluetooth: hci_qca: Use setup_timer Kernel API instead of init_timer
Replace init_timer function with setup_timer reported by coccinelle

Signed-off-by: Prasanna Karthik <pkarthik@intrinsyc.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-11-27 07:41:05 +01:00
Bhaktipriya Shridhar fac9a6021b Bluetooth: Remove deprecated create_singlethread_workqueue
The workqueue "workqueue" queues multiple work items viz &qca->ws_awake_rx
&qca->ws_rx_vote_off, &qca->ws_awake_device, &qca->ws_tx_vote_off which
require strict execution ordering. Hence, an ordered dedicated workqueue
has been used to replace the deprecated create_singlethread_workqueue
instance.

WQ_MEM_RECLAIM has not been set since the driver is not being used on a
memory reclaim path.

Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2016-09-19 20:19:34 +02:00
Marcel Holtmann 618e8bc228 Bluetooth: Use new hci_skb_pkt_* wrappers for drivers
The new hci_skb_pkt_* wrappers are mainly intented for drivers to
require less knowledge about bt_cb(sbk) handling. So after converting
the core packet handling, convert all drivers.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-11-19 17:50:27 +01:00
Linus Torvalds e880e87488 driver core update for 4.4-rc1
Here's the "big" driver core updates for 4.4-rc1.  Primarily a bunch of
 debugfs updates, with a smattering of minor driver core fixes and
 updates as well.
 
 All have been in linux-next for a long time.
 
 Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
 -----BEGIN PGP SIGNATURE-----
 Version: GnuPG v2
 
 iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
 Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
 =g7ZO
 -----END PGP SIGNATURE-----

Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core

Pull driver core updates from Greg KH:
 "Here's the "big" driver core updates for 4.4-rc1.  Primarily a bunch
  of debugfs updates, with a smattering of minor driver core fixes and
  updates as well.

  All have been in linux-next for a long time"

* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
  debugfs: Add debugfs_create_ulong()
  of: to support binding numa node to specified device in devicetree
  debugfs: Add read-only/write-only bool file ops
  debugfs: Add read-only/write-only size_t file ops
  debugfs: Add read-only/write-only x64 file ops
  debugfs: Consolidate file mode checks in debugfs_create_*()
  Revert "mm: Check if section present during memory block (un)registering"
  driver-core: platform: Provide helpers for multi-driver modules
  mm: Check if section present during memory block (un)registering
  devres: fix a for loop bounds check
  CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
  base/platform: assert that dev_pm_domain callbacks are called unconditionally
  sysfs: correctly handle short reads on PREALLOC attrs.
  base: soc: siplify ida usage
  kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
  kobject: explain what kobject's sd field is
  debugfs: document that debugfs_remove*() accepts NULL and error values
  debugfs: Pass bool pointer to debugfs_create_bool()
  ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
2015-11-04 21:50:37 -08:00
Marcel Holtmann aee61f7aa8 Bluetooth: hci_uart: Provide initial manufacturer information
Provide an early indication about the manufacturer information so that
it can be forwarded into monitor channel.

Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-10-21 07:20:44 +03:00
Viresh Kumar 621a5f7ad9 debugfs: Pass bool pointer to debugfs_create_bool()
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.

It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.

That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.

Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-04 11:36:07 +01:00
Prasanna Karthik a913718812 Bluetooth: hci_qca: Changed unsigned long to bool
'retransmit' being set in HCI_IBS_TX_WAKING case, using bool would be
efficient. Initialize local bool to false.

Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-28 13:06:13 +02:00
Prasanna Karthik ce26d8137b Bluetooth: hci_qca: Coding style clean up
Cleanup patch to fix spaces required reported by checkpatch

Signed-off-by: Prasanna Karthik <mkarthi3@visteon.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-09-17 13:20:07 +02:00
Marcel Holtmann f81b001a3e Bluetooth: hci_qca: Fix a few tab vs spaces issues
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2015-09-17 13:20:01 +02:00
Ben YoungTae Kim 10be6c0f27 Bluetooth: hciuart: Fix to use boolean flag with u32 type
debugfs_create_bool is asking to put u32 type pointer instead of bool
so that passing bool type with u32* cast will cause memory corruption
to read that value since it is handled by 4 bytes instead of 1 byte
inside.

Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-14 08:55:31 +02:00
Ben Young Tae Kim 0ff252c197 Bluetooth: hciuart: Add support QCA chipset for UART
QCA61x4 chips have supported sleep feature using In-Band-Sleep commands
to enable sleep feature based on H4 protocol. After sending
patch/nvm configuration is done, IBS mode will be up and running

Signed-off-by: Ben Young Tae Kim <ytkim@qca.qualcomm.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2015-08-10 23:52:20 +02:00