In original driver was implemented support for half-
and full-duplex modes, but it was not enabled. Instead
of it ks8851_rx_1msg method always returns "true" that
means "full-duplex" mode.
This patch replaces hard-coded functionality with
flexible solution that supports both SPI modes.
Signed-off-by: Sergey Shcherbakov <shchers@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mahesh Bandewar says:
====================
bonding: winter cleanup
Few cleanup patches that I have accumulated over some time now.
(a) First two patches are basically to move the work-queue initialization
from every ndo_open / bond_open operation to once at the beginning while
port creation. Work-queue initialization is an unnecessary operation
for every 'ifup' operation. However we have some mode-specific work-queues
and mode can change anytime after port creation. So the second patch is
to ensure the correct work-handler is called based on the mode.
(b) Third patch is simple and straightforward that removes hard-coded value
that was added into the initial commit and replaces it with the default
value configured.
(c) The final patch in the series removes the unimplemented "port-moved" state
from the LACP state machine. This state is defined but never set so
removing from the state machine logic makes code little cleaner.
(d) Reduce scope of some global variables to local.
Note: None of these patches are making any functional changes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Many of the bond param variables are declared global while it's not
really necessary for these variables to be global. So moving them to
the location these are used.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LACP state-machine defines "port-moved" state when the same ActorSystemID
and Port are seen in a LACPDU received on different port. The state is
never set since it's not implemented. However the state-machine attempts
to clear that state occasionally. LACP state machine is already complicated
and since this state is not implemented, removing it's checks makes the
state-machine little simpler.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliminate hard-coded value and use the default that is set.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initializing work-queues every time ifup operation performed is unnecessary
and can be performed only once when the port is created.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to move the work-queue initialization to port creation
from current port_open phase. Work-queue initialization does not make
sense every time we do 'ifup/ifdown'. So moving to port creation phase.
Arp monitoring work depends on the bonding mode and that is not tied
to the port creation and can change anytime during the life after port
creation. So this restructuring allows us to move the initialization
at creation without losing the ability to arm the correct work for the
mode user has selected.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski says:
====================
nfp: CRC32 RSS hash, port name reporting and misc fastpath cleanups
This series adds support for CRC32 RSS hash function to kernel API
of which NFP driver immediately makes use. There is also a
.ndo_get_phys_port_name() implementation conforming to switchdev
name format. Small patch takes advantage of napi_complete_done()'s
return code. Simon provides a fix for potentially trusting values
returned from FW too much.
A handful of unassuming fast path adjustments is also thrown in to make
the upcoming xdp_adjust_head() series easier to review.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Prevent theoretical buffer overrun by returning an error if
the number of entries returned by the firmware does not match those
present.
Also use a common handling error path.
Found by inspection.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Tested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need FW version in the first cache line of adapter struct
because we need to know the metadata format. To save space add a
metadata format bit.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of return code from napi_complete_done() to avoid rearming
interrupts when busy polling is on.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We really only need the device pointer on the fast path, stash it at
the beginning of the adapter structure and move pci_dev pointer down.
This saves up a few lines of code.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder variables longest to shortest to comply with netdev coding style.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We already print most of ring configuration including descriptors
in debugfs, add the few missing pieces and remove debug prints.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSP reports to us port labels. First id is the id of the physical
port, the other one tells us which logical interface is it within a
split port. Instead of printing them as string keep them in integer
format. Compute which interfaces are part of port split.
On netdev side use port labels and split information to provide a
.ndo_get_phys_port_name() implementation. We follow the name format
of mlxsw which is also suggested in "Port Netdev Naming" section
of Documentation/networking/switchdev.txt.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware images may reuse CRC32 hardware to compute RXHASH.
Make sure we report the correct hash function. Note that we don't
support changing functions at runtime. That would also require
a few more additions to the way the key is set because different
functions have different key sizes.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CRC32 engines are usually easily available in hardware and generate
OK spread for RSS hash. Add CRC32 RSS hash function to ethtool API.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the sock queue's spin locks get their lockdep
classes by the default init_spin_lock() initializer:
all socket families get - usually, see below - a single
class for rx, another specific class for tx, etc.
This can lead to false positive lockdep splat, as
reported by Andrey.
Moreover there are two separate initialization points
for the sock queues, one in sk_clone_lock() and one
in sock_init_data(), so that e.g. the rx queue lock
can get one of two possible, different classes, depending
on the socket being cloned or not.
This change tries to address the above, setting explicitly
a per address family lockdep class for each queue's
spinlock. Also, move the duplicated initialization code to a
single location.
v1 -> v2:
- renamed the init helper
rfc -> v1:
- no changes, tested with several different workload
Suggested-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Synopsys provides a new DesignWare Core Enterprise Ethernet MAC
IP (DWC-XLGMAC) for Ethernet designs. It is compliant with the
IEEE 802.3-2012 specifications, including IEEE 802.3ba and
consortium specifications.
This patch provides the initial 25G/40G/50G/100G Ethernet driver
for Synopsys XLGMAC IP Prototyping Kit.
Signed-off-by: Jie Deng <jiedeng@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Iyappan Subramanian says:
====================
drivers: net: xgene-v2: Add RGMII based 1G driver
This patch set adds support for RGMII based 1GbE hardware which uses a linked
list of DMA descriptor architecture (v2) for APM X-Gene SoCs.
v4: Address review comments from v3
- fixed local variable declarations to reverse christmas tree order
v3: Address review comments from v2
- fixed kbuild warnings (this 'if' clause does not guard)
v2: Address review comments from v1
- moved create_desc_ring and delete_desc_ring to open() and close()
respectively
- changed to use dma_zalloc APIs
- fixed tx_timeout()
- removed tx completion polling upper bound
- added error checking on rx packets
- added netif_stop_queue() and netif_wake_queue()
v1:
- Initial version
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a MAINTAINERS entry for the ethernet driver for
the on-chip ethernet interface which uses a linked list of DMA
descriptor architecture (v2) for APM X-Gene SoCs.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds,
- Transmit
- Transmit completion poll
- Receive poll
- NAPI handler
and enables the driver.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds,
- probe, remove, shutdown
- open, close and stats
- create and delete ring
- request and delete irq
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functions to configure ethernet hardware.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds functions to configure and control mac. This
patch also adds helper functions to get/set registers.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds DMA descriptor setup and interrupt enable/disable
functions.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for XPS.
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Satanand Burla <satananda.burla@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The axi variable was not being freed upon device removal.
With devm_kzalloc it ensures that it is properly freed.
Signed-off-by: Joao Pinto <jpinto@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_hw_addr_random() to set a random dev_addr and update
addr_assign_type instead of open-coding it.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a Kconfig option: CONFIG_TIGON3_HWMON which allows to build
in/out support for thermal sensors reported by Tigon3 NICs.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Petazzoni says:
====================
net: mvpp2: add initial support for PPv2.2
The goal of this patch series is to add basic support for PPv2.2 in
the existing mvpp2 driver. mvpp2 currently supported the PPv2.1
version of the IP, used in the 32 bits Marvell Armada 375 SoC. PPv2.2
is an evolution of this IP block, used in the 64 bits Marvell Armada
7K/8K SoCs.
In order to ease the review, the introduction of PPv2.2 support has
been made into multiple small commits, with the final commit adding
the compatible string that makes the PPv2.2 support actually
usable. The series remain fully bisectable.
People interested in testing the code will find the full series (plus
a few Device Tree patches) at:
https://github.com/MISL-EBU-System-SW/mainline-public/tree/4.11/mvpp2.2-support-v3
I'd like to thank Stefan Chulski and Marcin Wojtas, who helped me a
lot in the development of this patch series, by reviewing the patches,
and giving lots of useful hints to debug the driver on PPv2.2. Thanks
as well to Russell King for reviewing previous iterations of this
series, and providing suggestions and fixes.
Changes between v2 and v3:
- Rebased on v4.11-rc1.
- Add patch "net: mvpp2: fix DMA address calculation in
mvpp2_txq_inc_put()", to properly take into account the "packet
offset" field of the TX descriptors. Without this, we were getting
DMA_API_DEBUG warnings that we are unmapping DMA mappings with a
non-mapped DMA address.
- In patch "net: mvpp2: add and use accessors for TX/RX descriptors",
add a function named mvpp2_txdesc_offset_get(), which is needed for
the DMA address calculation fix.
- In patch "net: mvpp2: add and use accessors for TX/RX descriptors",
fix the calculation of tx_desc physical address and packet offset
in mvpp2_tx_frag_process(). The offset was assigned into the buffer
physical address, and the physical address to the packet offset,
which meant the fragment process was completely broken.
- In patch "net: mvpp2: adjust the allocation/free of BM pools for
PPv2.2" fix how MVPP22_BM_ADDR_HIGH_VIRT_RLS_MASK is used. This
mask is already shifted. So the value should be shifted before
being masked and not the opposite.
- Add a new patch "net: mvpp2: set dma mask and coherent dma mask on
PPv2.2", to set the DMA mask and DMA coherent mask. By setting the
DMA mask to 40 bits we avoid using bounce buffers when network
packets are above the 4 GB limit. The coherent mask remains set to
32 bits, because the BM pools must all have the same high 32 bits
in their addresses.
- Use "dma" instead of "phys" where appropriate, as suggested by
Russell King.
- Use the "cookie" field of the RX descriptor to store the physical
address instead of the virtual address, and then use phys_to_virt()
to get the virtual address. This allows to work around the limit
that the "cookie" field only has 40 bits, which is not sufficient
to store a virtual address on 64 bits platforms. This was suggested
by Russell King.
As part of this change, also got rid of all the compile time
conditionals on CONFIG_ARCH_DMA_ADDR_T_64BIT, to get better
compile-time coverage.
- In patch "net: mvpp2: handle misc PPv2.1/PPv2.2 differences":
* Instead of calling mvpp21_port_power_up(port) only on PPv2.1,
remove this function, and call its relevant parts directly from
->probe(). Only mvpp2_port_fc_adv_enable() is PPv2.1
specific. Reported by Russell King.
* Add a mvpp22_port_mii_set() function that properly initializes
SGMII support on PPv2.2. Code provided by Russell King.
- In patch "net: mvpp2: handle register mapping and access for PPv2.2":
* Adjust the code to match the change of the DT binding in terms
of mapping the second register area on PPv2.2.
* Rework the register accessors to remove the get_cpu()/put_cpu(),
and instead use separate accessors for global registers
vs. per-CPU registers.
- Add a few new patches removing dead/unused/useless code:
net: mvpp2: remove support for buffer header
net: mvpp2: remove unused register definition MVPP2_TXQ_THRESH_REG
net: mvpp2: remove mvpp2_txq_pend_desc_num_get() function
- Fix a number of checkpatch warnings.
Changes between v1 and v2:
- Made a separate series from the set of patches doing preparation
changes/fixes to the mvpp2 driver.
- Rebased on top of v4.10-rc1.
- Update Kconfig text of the mvpp2 driver to mention the support for
Armada 7K and 8K (PPv2.2).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the mvpp2 driver has been modified to accommodate the support
for PPv2.2, we can finally advertise this support by adding the
appropriate compatible string.
At the same time, we update the Kconfig description of the MVPP2 driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On PPv2.2, the streaming mappings can be anywhere in the first 40 bits
of the physical address space. However, for the coherent mappings, we
still need them to be in the first 32 bits of the address space,
because all BM pools share a single register to store the high 32 bits
of the BM pool address, which means all BM pools must be allocated in
the same 4GB memory area.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 variant of the network controller needs an additional
clock, the "MG clock" in order for the IP block to operate
properly. This commit adds support for this additional clock to the
driver, reworking as needed the error handling path.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PPv2.1, we have a maximum of 8 RXQs per port, with a default of 4
RXQs per port, and we were assigning RXQs 0->3 to the first port, 4->7
to the second port, 8->11 to the third port, etc.
In PPv2.2, we have a maximum of 32 RXQs per port, and we must allocate
RXQs from the range of 32 RXQs available for each port. So port 0 must
use RXQs in the range 0->31, port 1 in the range 32->63, etc.
This commit adapts the mvpp2 to this difference between PPv2.1 and
PPv2.2:
- The constant definition MVPP2_MAX_RXQ is replaced by a new field
'max_port_rxqs' in 'struct mvpp2', which stores the maximum number of
RXQs per port. This field is initialized during ->probe() depending
on the IP version.
- MVPP2_RXQ_TOTAL_NUM is removed, and instead we calculate the total
number of RXQs by multiplying the number of ports by the maximum of
RXQs per port. This was anyway used in only one place.
- In mvpp2_port_probe(), the calculation of port->first_rxq is adjusted
to cope with the different allocation strategy between PPv2.1 and
PPv2.2. Due to this change, the 'next_first_rxq' argument of this
function is no longer needed and is removed.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adjusts how the MVPP2_ISR_RXQ_GROUP_REG register is
configured, since it changed between PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 unit is connected to an AXI bus on Armada 7K/8K, so this
commit adds the necessary initialization of the AXI bridge.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit handles a few miscellaneous differences between PPv2.1 and
PPv2.2 in different areas, where code done for PPv2.1 doesn't apply for
PPv2.2 or needs to be adjusted (getting the MAC address, disabling PHY
polling, etc.).
Thanks to Russell King for providing the initial implementation of
mvpp22_port_mii_set().
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adjusts the mvpp2 driver register mapping and access logic
to support PPv2.2, to handle a number of differences.
Due to how the registers are laid out in memory, the Device Tree binding
for the "reg" property is different:
- On PPv2.1, we had a first area for the packet processor
registers (common to all ports), and then one area per port.
- On PPv2.2, we have a first area for the packet processor
registers (common to all ports), and a second area for numerous other
registers, including a large number of per-port registers
In addition, on PPv2.2, the area for the common registers is split into
so-called "address spaces" of 64 KB each. They allow to access per-CPU
registers, where each CPU has its own copy of some registers. A few
other registers, which have a single copy, also need to be accessed from
those per-CPU windows if they are related to a per-CPU register. For
example:
- Writing to MVPP2_TXQ_NUM_REG selects a TX queue. This register is a
per-CPU register, it must be accessed from the current CPU register
window.
- Then a write to MVPP2_TXQ_PENDING_REG, MVPP2_TXQ_DESC_ADDR_REG (and
a few others) will affect the TX queue that was selected by the
write to MVPP2_TXQ_NUM_REG. It must be accessed from the same CPU
window as the write to the TXQ_NUM_REG.
Therefore, the ->base member of 'struct mvpp2' is replaced with a
->cpu_base[] array, each entry pointing to a mapping of the per-CPU
area. Since PPv2.1 doesn't have this concept of per-CPU windows, all
entries in ->cpu_base[] point to the same io-remapped area.
The existing mvpp2_read() and mvpp2_write() accessors use cpu_base[0],
they are used for registers for which the CPU window doesn't matter.
mvpp2_percpu_read() and mvpp2_percpu_write() are new accessors added to
access the registers for which the CPU window does matter, which is why
they take a "cpu" as argument.
The driver is then changed to use mvpp2_percpu_read() and
mvpp2_percpu_write() where it matters.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PPv2.2, the MVPP2_RXQ_DESC_ADDR_REG and MVPP2_TXQ_DESC_ADDR_REG
registers have a slightly different layout, because they need to contain
a 64-bit address for the RX and TX descriptor arrays. This commit
adjusts those functions accordingly.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit modifies the mvpp2_defaults_set() function to not do the
loopback and FIFO threshold initialization, which are not needed for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP2_RXQ_CONFIG_REG register has a slightly different layout
between PPv2.1 and PPv2.2, so this commit adapts the functions modifying
this register to accommodate for both the PPv2.1 and PPv2.2 cases.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adjusts the allocation and freeing of BM pools to support
PPv2.2. This involves:
- Checking that the number of buffer pointers is a multiple of 16, as
required by the hardware.
- Adjusting the size of the DMA coherent area allocated for buffer
pointers. Indeed, PPv2.2 needs space for 2 pointers of 64-bits per
buffer, as opposed to 2 pointers of 32-bits per buffer in
PPv2.1. The size in bytes is now stored in a new field of the
mvpp2_bm_pool structure.
- On PPv2.2, getting the DMA address and cookie (used for the physical
address) of each buffer requires reading the
MVPP22_BM_ADDR_HIGH_ALLOC to get the high order bits of those
addresses. A new utility function mvpp2_bm_bufs_get_addrs() is
introduced to handle this.
- On PPv2.2, releasing a buffer requires writing the high order 32 bits
of the DMA address and cookie to MVPP22_BM_PHY_VIRT_HIGH_RLS_REG.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the definition of the PPv2.2 HW descriptors, adjusts
the mvpp2_tx_desc and mvpp2_rx_desc structures accordingly, and adapts
the accessors to work on both PPv2.1 and PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the format of the HW descriptors is different between PPv2.1 and
PPv2.2, this commit introduces an intermediate union, with for now
only the PPv2.1 descriptors. The bulk of the driver code only
manipulates opaque mvpp2_tx_desc and mvpp2_rx_desc pointers, and the
descriptors can only be accessed and modified through the accessor
functions. A follow-up commit will add the descriptor definitions for
PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to the introduction for the support of PPv2.2 in the
mvpp2 driver, this commit adds a hw_version field to the struct
mvpp2, and uses the .data field of the DT match table to fill it in.
Having the MVPP21 and MVPP22 definitions available will allow to start
adding the necessary conditional code to support PPv2.2.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 IP has a different TX and RX descriptor layout compared to
PPv2.1. In order to prepare for the introduction of PPv2.2 support in
mvpp2, this commit adds accessors for the different fields of the TX
and RX descriptors, and changes the code to use them.
For now, the mvpp2_port argument passed to the accessors is not used,
but it will be used in follow-up to update the descriptor according to
the version of the IP being used.
Apart from the mechanical changes to use the newly introduced
accessors, a few other changes, needed to use the accessors, are made:
- The mvpp2_txq_inc_put() function now takes a mvpp2_port as first
argument, as it is needed to use the accessors.
- Similarly, the mvpp2_bm_cookie_build() gains a mvpp2_port first
argument, for the same reason.
- In mvpp2_rx_error(), instead of accessing the RX descriptor in each
case of the switch, we introduce a local variable to store the
packet size.
- In mvpp2_tx_frag_process() and mvpp2_tx() instead of accessing the
packet size from the TX descriptor, we use the actual value
available in the function, which is used to set the TX descriptor
packet size a few lines before.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX descriptors of the PPv2 hardware allow to store several
information, amongst which:
- the DMA address of the buffer in which the data has been received
- a "cookie" field, left to the use of the driver, and not used by the
hardware
In the current implementation, the "cookie" field is used to store the
virtual address of the buffer, so that in the receive completion path,
we can easily get the virtual address of the buffer that corresponds to
a completed RX descriptors.
On PPv2.1, used on 32-bit platforms, those two fields are 32-bit wide,
which is enough to store a DMA address in the first field, and a virtual
address in the second field.
On PPv2.2, used on 64-bit platforms, these two fields have been extended
to 40 bits. While 40 bits is enough to store a DMA address (as long as
the DMA mask is 40 bits or lower), it is not enough to store a virtual
address. Therefore, the "cookie" field can no longer be used to store
the virtual address of the buffer.
However, as Russell King pointed out, the RX buffers are always
allocated in the kernel linear mapping, and therefore using
phys_to_virt() on the physical address of the RX buffer is possible and
correct.
Therefore, this commit changes the driver to use the "cookie" field to
store the physical address instead of the virtual
address. phys_to_virt() is used in the receive completion path to
retrieve the virtual address from the physical address.
It is obviously important to realize that the DMA address and physical
address are two different things, which is why we store both in the RX
descriptors. While those addresses may be identical in some situations,
it remains two distinct concepts, and both addresses should be handled
separately.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvpp2_txq_pend_desc_num_get() function only selects a TX queue, and
reads the number of pending descriptors. It is used in only one place,
in mvpp2_txq_clean(), where the TX queue has already been selected by a
write to MVPP2_TXQ_NUM_REG.
Therefore, this function is useless, and the caller can simply read the
value of the MVPP2_TXQ_PENDING_REG register instead.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This register is no longer used since commit edc660fa09 ("net: mvpp2:
replace TX coalescing interrupts with hrtimer").
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sergey Shcherbakov