Add another ID for a 7000 series device.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the stations are being restored because of unassoc
RXON, the LQ cmd may not have been initialized because it
is initialized only after association.
Sending zeroed LQ_CMD makes the fw unhappy: it raises
SYSASSERT_2078.
Cc: stable@vger.kernel.org
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
[move zero_lq and make static const]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make power management in MVM driver enabled by default and
remove using the power_save module parameter. Rely only on
the power_scheme parameter to decide if power management
should be used.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We can check buf against NULL instead of having additional bool
variable.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If on iwl_dump_nic_event_log() error occurs before that function
initialize buf, we process uninitiated pointer in
iwl_dbgfs_log_event_read() and can hit "BUG at mm/slub.c:3409"
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=951241
Cc: stable@vger.kernel.org
Reported-by: ian.odette@eprize.com
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently in low power (LP) mode FW moved from active to power save mode
after TX/RX completion faster than in balanced power mode (BPS).
Change AM-to-PSM transition time so that it will be the same as for BPS.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
first_antenna is supposed to return the first antenna as a
0-based bitmap: ANT_A is BIT(0), ANT_B is BIT(1), etc...
Since ffs is 1 based (ffs(BIT(0)) = 1), then we had an
off-by-one bug:
BIT(ffs(ANT_A)) = BIT(ffs(BIT(0))) = BIT(1) = ANT_B.
So what we really want is:
BIT(ffs(ANT_A) - 1) = BIT(ffs(BIT(0)) - 1) = BIT(0) = ANT_A.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Chain noise is done in the firmware and Bluetooth Coexistence
is implemented now.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for the secondary channel offset IE in channel
switch announcements. This is necessary for proper handling
of CSA on HT access points.
For this to work it is also necessary to convert everything
here to use chandef structs instead of just channels. The
driver updates aren't really correct though. In particular,
the TI wl18xx driver update can't possibly be right since
it just ignores the new channel width for lack of firmware
API.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Do not implement this in b43, but use bcma_pmu_spuravoid_pllupdate().
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pretty much everywhere that uses a trace definition
header that's not in include/trace/events/ uses the
make system for the include path rather than putting
it into the sources, so do that in ath5k as well.
This came up during backporting work (where this is
required), but since all other drivers do it this
way upstream it seemed applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This came up during my backporting work but it seems
perfectly appropriate for the kernel as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The value can be obtained from the struct brcmf_if object pointer
and it is used only twice.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Replace the function by brcmf_fws_mac_desc_closed(). The new function
is used in the transmit path and in the dequeue worker.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of passing the ifidx and lookup the ifp inside the
function brcmf_fws_find_mac_desc() simply pass the ifp as
parameter.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_fws_find_mac_desc() determines the descriptor
associated with a sk_buff for firmware-signalling. It needs the
interface type to do that. For this a helper function is added in
wl_cfg80211.c.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for platform specific data for SDIO
fullmac devices. Currently OOB interrupts are configured by Kconfig
BRCMFMAC_SDIO_OOB but that is now determined dynamically by checking
availibility of platform data.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Added sdio device id to list of supported devices. 43143 is a new
802.11n single stream device.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BCM4335 is an a/b/g/n/ac WiFi chip that supports up to 80MHz channel. This patch
adds support for this chip through SDIO interface.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set device in a manner that SDIO I/O card reset
will lead to WLAN backplane and PMU state reset.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer WiFi chip use ARM CR4 core to achieve higher performance. Add necessary
code for host driver in order to support CR4 core.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adopting the new d11 interface for 11ac fullmac chip support.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
802.11 core interface is upgraded with 11ac support. Add channel spec support
code to brcmutil.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enter/exit download state routine is going to diverge with new ARM core
introduced. Move corresponding code to sdio_chip.c for new ARM core support.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For fullmac chips host driver can access to dongle RAM through SDIO function 1.
Introduce brcmf_sdio_ramrw and place it at bcmsdh.c with other interface
functions.
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Save & restore is an advanced power saving feature,
supported only on selected devices.
SR operation is almost completely transparent to the driver.
Support for it is hardware and firmware dependent.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware parsing of Control Wrapper Frames needs to be disabled, as
it has been causing spurious decryption error reports. The initvals for
other chips have been updated to disable it, but AR9580 was left out for
some reason.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Properly register our mac80211_hwsim_driver, attach it to the platform bus.
Bind newly created hwsim devices to that driver, so that our wlan devices get
a proper "driver" sysfs attribute.
This makes mac80211_hwsim interfaces work with NetworkManager.
Signed-off-by: Martin Pitt <martin.pitt@ubuntu.com>
[fix an old and a new message to not be line-broken,
also fix the driver_register error path]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There is better to use kstrto* instead of simple_strtoul. In this case it
applies a bit stricter rules for input as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In routine _rtl8188e_read_power_value_fromprom(), there are loops initializing
index_cck_base and index_bw40_base from the PROM. As the result of a typo, the
second loop is ended one element too soon.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Inside one FIFO slot queue, EDMA chipsets have the same link pointer
re-read race condition as older chipsets, so the same buffer holding
logic needs to be used in order to avoid use-after-free bugs.
Unlike on older chips, it can be skipped for the end of the queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If AR_CRCErr, AR_PHYErr, AR_DecryptCRCErr or AR_MichaelErr is indicated
in the rx status word, but AR_RxFrameOK is also set, the descriptor
contents are typically invalid. This can show up as a warning about
invalid MCS rates in a frame. Even with those checks in place, a
descriptor with invalid MCS rates can still sometimes make it through to
the driver (mostly on older hardware like AR91xx).
Detect such errors in the last descriptor of a frame and discard the
whole frame if present.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the comment in ath_get_next_rx_buf indicates, if a descriptor with
the done bit set follows one with the done bit cleared, both descriptors
should be discarded, however the driver is not doing that yet.
To fix this, use the rs->rs_more flag as an indicator that the following
frame should be discarded. This also helps with the split buffer case:
if the first part of the frame is discarded, the following parts need to
be discarded as well, since they contain no valid header or usable data.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of leaving the buffer without skb and breaking out of the loop
(which could leak the rx buffer), use the common error path.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Banks 0-3,7 are neither modified at run time, nor SREV dependent.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two sets of initvals for this RF bank, one with TPC support and
one without.
The TPC one always gets used, so remove the other one to avoid confusion.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All users are converted to use the rt2x00mmio_*
functions so remove the now unused defines.
The patch contain no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the recently introduced rt2x00mmio_* routines
instead of the rt2x00pci_* variants.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions in the rt2x00mmio module has been
moved from the rt2x00pci module. Each function
uses the rt2x00pci prefix which is a bit confusing.
Use the r2x000mmio prefix for each function to make
it consistent with the module name.
The renamed functions are used by several modules,
and updating the names in all of them would result
in a big patch. In order to keep the patch simple,
add compatibility defines for the old function
names. This allows to update the names in each
module separately. After each module is updated,
the defines can be removed.
The patch contains no functional changes.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And make use of it in b43. This fixes a regression introduced with
49d55cef5b
b43: N-PHY: implement spurious tone avoidance
This commit made BCM4322 use only MCS 0 on channel 13, which of course
resulted in performance drop (down to 0.7Mb/s).
Reported-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In brcmf_rx_frames() the call to brcmf_fweh_process_skb() could
change the ifidx using information in the event data. This is
only different to the BDC ifidx for IF ADD event. However, the
creation of the new interface is deferred to event worker so
it does not exist. After brcmf_fweh_process_skb() it is only
used to set statistics.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_p2p_notify_action_frame_rx() the wireless_dev
is needed to pass the action frame to cfg80211. The wireless_dev
is held in brcmf_cfg80211_vif object. Use that instead of the
ieee80211_ptr in net_device as P2P_DEVICE interface does not have
a net_device associated with it.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The probe requests received on P2P_DEVICE interface were not sent
to wpa_supplicant, which makes the device not discoverable by peers.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware sends a IF event to notify the host driver that the
P2P_DEVICE interface has been created. Wait for the event before
returning the related wireless_dev.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current driver code creates a P2P_DEVICE through a module
parameter. This device has a dummy netdevice which is not how this
interface type is intended. This patch add proper support for the
P2P_DEVICE interface type. This requires a wpa_supplicant with such
support as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
escan functionality is also required for P2P device operations so it
is better not to rely on struct netdevice instances.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove use of struct netdevice as parameter to brcmf_set_mpc() as it
will not always be available, ie. there will be non-netdevice interfaces.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the introduction of the P2P_DEVICE interface type an instance of
struct wireless_dev does not always have a netdev assigned to it. Better
use container_of() construct to obtain internal structure and go from
there.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In fweh module the event handler was only called if the
struct brcmf_if instance had a non-null netdev associated.
This restriction is no longer valid for P2P_DEVICE type
of interface. This patch removes that restriction.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
According specification the IF event has an additional field indicating
the role or type of the interface for which this event is sent.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adds a trace function used in brcmf_dbg_hex_dump() which adds the
raw binary data to the trace. It requires trace-cmd plugin to see
this data.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firware shared data structure is backward compatible for fields
we are interested in.
Allow reading of shared data in case of version mismatch.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware console output can be read also when there was
no trap indication.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware can request the host driver for packets, by sending
either the MAC_REQUEST_CREDIT or the MAC_REQUEST_PACKET primitive.
This patch adds handling of these primitives.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can signal whether the host driver may sent packets for
a specific destination or interface. This can happen when a
destination is sleeping or when going off-channel.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
reported by Hante. Needs to be squashed in commit 187fbcec.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not locking ra_list when dequeuing packets creates race conditions.
When adding a packet 'tx_pkts_queued' is modified before setting
highest_priority_queue. If in-between the main loop starts, it will
see a packet queued (tx_pkts_queued > 0) but will not find it, since
max prio is not set yet. Depending on the scheduling, the thread
trying to add the packet could complete and restore the situation.
But this is not something to rely on.
Another race condition exists, if a new packet, exceeding current
max prio is added. If concurrently a packet is dequeued, the newly
set max prio will be overwritten with the value of the dequeued
packet. This can occur, because selecting a packet and modifying
the max prio is not atomic. The result in an infinite loop unless,
a new packet is added that has at least the priority of the hidden
packet.
Same applies to bss_prio_tbl. Forward iteration is no proper
lock-free technique and provides no protection from calls to
list_del. Although BSS are currently not added/removed dynamically,
this must not be the case in the future. Hence always hold proper
locks when accessing those lists.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using NO_PKT_PRIO_TID and tx_pkts_queued to check for an empty
state, can lead to a contradictory state, resulting in an
infinite loop. Currently queueing and dequeuing of packets is
not synchronized, and can happen concurrently. While tx_pkts_queued
is incremented when adding a packet, max prio is set to NO_PKT when
the WMM list is empty. If a packet is added right after the check
for empty, but before setting max prio to NO_PKT, that packet is
trapped and creates an infinite loop.
Because of the new packet, tx_pkts_queued is at least 1, indicating
wmm lists are not empty. Opposing that max prio is NO_PKT, which
means "skip this wmm queue, it has no packets". The infinite loop
results, because the main loop checks the wmm lists for not empty
via tx_pkts_queued, but for dequeing it uses max_prio to see if it
can skip current list. This will never end, unless a new packet is
added which will restore max prio to the level of the trapped packet.
The solution here is to rely on tx_pkts_queued solely for checking
wmm queue to be empty, and drop the NO_PKT define. It does not
address the locking issue.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ra_list_spinlock is used to protect struct mwifiex_wmm_desc and
embedded structures such as ra_list. tid_tbl_lock while more fine
grained, is not used but in one function. That function is not
called reentrantly. To protect ra_list from concurrent modification
ra_list_spinlock must be held.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
adapter->bss_prio_tbl list has already been checked in outer loop.
The inner loop works with priv_tmp->wmm.tid_tbl_ptr list. Also the
lock taken, gives hint that this is likely a copy-paste error.
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
An allyesconfig build of rtl8188ee yields the following duplicate entry points:
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `.rtl92c_phy_ap_calibrate':
(.text+0x21d14): multiple definition of `.rtl92c_phy_ap_calibrate'
drivers/net/wireless/rtlwifi/rtl8192c/built-in.o:(.text+0xb1e8): first defined here
drivers/net/wireless/rtlwifi/rtl8188ee/built-in.o: In function `rtl_hal_pwrseqcmdparsing':
(.opd+0xed0): multiple definition of `rtl_hal_pwrseqcmdparsing'
One of the routines is not used and can be deleted, the other is renamed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Building rtl8188ee yields warnings such as the following:
x86_64-linux-gcc: warning: drivers/net/wireless/rtlwifi: linker input file unused because linking not done
The only potential cause is an extraneous space in the make file.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These are the remaining knobs in ath9k to support DFS:
* mark AR9280 and AR9580 as DFS tested
* synchronize DFS regulatory domain to reg notifyer
* set required RX filter flags for radar detection
* process radar PHY errors at DFS detector
* notify DFS master on radar detection
DFS support requires CONFIG_ATH9K_DFS_CERTIFIED to be set.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This helps testing DFS without radar generating
equipment and is required for certification.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Should make the warning messages more useful.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cmd_pending is increased in mwifiex_wait_queue_complete() and
decreased in mwifiex_complete_cmd() currently.
If there are two or more commands in the cmd_pending_q the main
worker thread will pick up next command from cmd_pending_q
automatically after finishing current command. As a result
mwifiex_wait_queue_complete() will not be called because
the command is alreay completed. This leads to a negative
number in cmd_pending count.
Fix it by increasing cmd_pending when a cmd is queued into
cmd_pending_q and decreasing when that cmd is recycled. For scan
commands we don't perform inc/dec operations until it's moved
from scan_pending_q to cmd_pending_q. This covers both
synchronous and asynchronous commands.
Reported-by: Daniel Drake <dsd@laptop.org>
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware is requested from user-space. To assure the request
is handled it is recommended to do the request upon IFF_UP. For
a mac80211 driver the .start() callback can be considered the
equivalent.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For v3.9 kernel the P2P functionality was merged, but it does
not fully support the P2P_DEVICE interface type. This patch
removes advertising that support.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the firmware has been open sourced, the minor version has been
bumped to 1.4 and the API/ABI will stay compatible across further 1.x
releases.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now we didn't handle properly the FLUSH ampdu action
coming from mac80211. This could result in SCD queue leak:
mac80211 would STOP_FLUSH an AMPDU Tx session and remove
the station. If we had still packets on the ring, we
wouldn't deallocate the SCD queue and wait for it to be
empty.
The indication of the queue being empty comes from the Tx
response flow which relies on the tid_data structure. The
problem is that this structure has been cleared when the
station has been removed.
In order to solve this issue, block in the STOP_FLUSH
ampdu_action until the SCD queue is flushed, and only then,
let mac80211 move forward to remove the station.
iwlagn_txfifo_flush had to be enhanced to allow this.
The bug fixed here caused the "txq_id mismatch: 12 0" print.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In commit 332235427a
"iwlwifi: mvm: take the valid_{rx,tx}_ant from the TLV"
I replaced the access to nvm_data->valid_tx_ant to an inline
cheking the TLV flags but forgot a few occurences. Fix that.
Change-Id: I92daac735b46738d97fe2dbd5934bb177fd0751b
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-on: https://gerrit.rds.intel.com/12308
Tested-by: IWL Jenkins
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If request_module() failed then we didn't have the correct
opmode module that the driver needs to function, so print
a warning in this case to make it more obvious what could
be wrong. This still won't catch the case where the module
simply doesn't exist because it wasn't compiled though.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Drivers can now advertise VHT support even if they don't use channel
contexts.
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/nfc/microread/mei.c
net/netfilter/nfnetlink_queue_core.c
Pull in 'net' to get Eric Biederman's AF_UNIX fix, upon which
some cleanups are going to go on-top.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It actually handles a BT coex notification, so rename it
to be more self explained.
Also, this function can always look at mvm->last_bt_notif
provided that the latter is updated on time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Using IWL_MVM_STATION_COUNT and IWL_INVALID_STATION together
isn't a good idea as they have different values. Always use
IWL_MVM_STATION_COUNT for an invalid station in MVM and move
the definition of the IWL_INVALID_STATION constant into the
DVM driver to avoid making such mistakes again. The one use
in the transport code can be hard-coded to -1 instead as the
station ID is passed as an integer there.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
some new thinkpad laptops use intel chip with new pci id need be added
lspci -vnn output:
Network controller [0280]: Intel Corporation Centrino Advanced-N 6235
[8086:088f] (rev 24)
Subsystem: Intel Corporation Device [8086:5260]
Signed-off-by: Shuduo Sang <sangshuduo@gmail.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iterators don't need to know what bt_kill_msk means.
All they need to know is if reduced Tx power is enabled
on an interface or not. So change the member of the
iterator to be a bool.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware API changed to differentiate between event and
fragment start/end. Change the time-event handling accordingly.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Many platforms have issues processing a wakeup signal
while they're still suspending, and will ignore it.
Since our device thinks it woke the platform, and the
platform ignored the signal, it will sleep without
WoWLAN being enabled as the device disables WoWLAN
when having woken the platform.
Resolve this by making the device wait for 10 seconds
after getting the suspend signal before waking up the
platform.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The function just wraps an existing one, remove it.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The requirement for TX/RX active to powersave transition time for
the Balanced Power Save (BPS) scheme changed. Change the driver
accordingly and set transition time to 100 msec.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Encapsulate the power table command logging in a separate
function to print the same information in both cases.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The firmware starts sending nulldata frames for keepalive immediately
after association, regardless of power management state. The driver
thus needs to configure keep alive period unconditionally.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The driver distinguishes between power management and device's power
down enablement. Power management enablement depends both on driver's
module power parameters and mac80211 decision. The device's power down
depends only on driver's module power parameters. Change the driver to
always send Power Table command to enable or disable both power
management and device's power down.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Active to power save mode transition time for TX/RX in the power
table command is in microseconds, fix the units in the driver.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently power management is supported only when only a single
virtual interface is present. The driver verifies number of created
interfaces and disables power management when multiple interfaces
present. However, this rule does not extend to a P2P device that is
handled differently in the firmware. If a P2P device is added power
management can remain enabled.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace SLEEP_OVER_DTIM by SKIP_OVER_DTIM.
Add iwl_mvm prefix to a function name.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Current available FW still doesn't support new PM API.
Therefore, to enable basic power management with the
existing firmware, change the API in the driver back
to the API used in the current firmware.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we roam to A band, we don't need to constraint WiFi
any more since it is operating on a different band.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows to have better wifi TPT when BT is active under
good RSSI conditions.
Wifi will have better chance to send Acks and Cts even if BT
is active.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the per-interface debugfs infrastructure to create a
directory and symlink, and add a file containing debug
data related to each virtual interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Firmware provides the driver with credits used to transmit packets
to the firmware. When credits run out the packets should be queued
and dequeued when receiving creditback signals from the firmware.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The fcmode provided by module parameter defaults to NONE, which
means no flow-control is required. In this case flow-control
signals should not be enabled.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Bail out of brcmf_fws_init() when no firmware-signalling is asked
for. Need to take this into account in brcmf_fws_deinit() as well.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The functions are moved in preparation of later patches.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length is not according specification so better fix it.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iovar to the firmware fails the firmware-signalling module
does a cleanup for which it needs pointer to struct brcmf_pub, which
it gets from struct brcmf_fws_info::drvr. Assign this field before
doing the tlv iovar.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The low-level sdio code has a large number of trace and info messages
that are mostly useful looking into bus specific issues. For tracing
higher-level driver functions it is better to have a dedicated level
for low-level sdio debugging.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Ia424ff18d9033b97aeffc248358e50c51805e815
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/74
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During SDIO layer flow control signalling firmware can issue
invalid packets. Prevent printing of parsing errors in such case.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing the tlv upon receiving frames can fail. Instead of printing
an error message, just count the parse failure. On some devices we
receive a lot of invalid tlv signals.
this commit will be squashed.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: I08e0f62c55e5028f9aa70c396d291679abd273c9
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/72
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When firmware-signalling is active the brcmf_txcomplete() does
a free of the sk_buff when transfer to firmware fails in the
bus-specific driver code. However, it should also cleanup the
packet from the hanger. This patch fixes that.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling the tx status signalling, which requires packet tagging
before sending to the firmware and handling the tx status signal.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Upcoming patches will add firmware signalled flow control. Prepare
by adding the mode, which defaults to disable it. The mode can be
queried by brcmf_fws_fc_active() and set by a module parameter.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a callback to obtain packet queue from the bus-specific code
used to cleanup packet buffers from firmware-signalling code.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hanger for firmware-signalling is used to retain information for
outstanding transmit packets that await tx status.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an interface is deleted make sure to cleanup all packet
buffers related to that interface.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sk_buff structure contains a control buffer that can be used
by different layers in the networking stack for holding packet
associated information. In brcmfmac it is used to hold firmware
signalling related information.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the netif queue is only stopped when the bus interface is
giving a push back. This will change soon so prepare the driver by
adding a stop reason and stop/resume the queue accordingly.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a cleanup function releasing any queued packet buffers in
the mac descriptor entries.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The firmware signalling functionality needs the credit map firmware
events. This patch adds registration of a handler for this event.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware can signal the driver to allocate descriptor info for a given
mac address, which will be used for flow control and host queueing.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware signalling needs to handle resources upon interface
events. This patch add calls in the interface event handling
routine.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use information from the device to determine the bands property
of the wiphy object. After this change the support of 80211n is
correctly presented in the bands property.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In brcmf_sdbrcm_txpkt() a new packet is allocated and used to transmit
to firmware freeing up the original packet. However, that packet is
still referenced in firmware-signalling so this would result in a
double free. Using skb_cow() avoids this as the packet reference is
unchanged.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When taking care of packet alignment to 64-byte boundary padding may
be added between SDPCM header and CDC data. It clear both SDPCM header
space and padding space. Changed it to only clear padding space. In
filling the SDPCM header it uses unaligned access to set SDPCM software
header, but preceding code assures it is properly aligned.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Change-Id: Iad22f277f3496440ba4d2db771205714774570ac
Reviewed-on: http://lb-bun-88.bun.broadcom.com:8080/76
Reviewed-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The function brcmf_sdbrcm_txpkt() calls brcmf_txcomplete() with
a parameter success. For this parameter it passes ret != 0, but
that condition is true upon failure.
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rt2800pci driver supports the built-in wireless
MAC of the Ralink RT3x5x SoCs. However building the
driver for these SoCs leads to the following error:
LD init/built-in.o
drivers/built-in.o: In function `rt2800pci_rxdone_tasklet':
<...>/drivers/net/wireless/rt2x00/rt2800pci.c:1012: undefined reference to `rt2x00pci_rxdone'
drivers/built-in.o:(.rodata+0x4780): undefined reference to `rt2x00pci_initialize'
drivers/built-in.o:(.rodata+0x4784): undefined reference to `rt2x00pci_uninitialize'
drivers/built-in.o:(.rodata+0x47bc): undefined reference to `rt2x00pci_flush_queue'
drivers/built-in.o:(.rodata+0x4818): undefined reference to `rt2x00pci_regbusy_read'
make[5]: *** [vmlinux] Error 1
The missing functions are provided by the rt2x00pci
module. This module is only selected by the rt2800pci
driver if PCI support is enabled in the kernel, because
some parts of the rt2x00pci code depends on PCI support.
PCI support is not available on the RT3x5x SoCs because
those have no PCI host controller at all.
Move the non PCI specific code from rt2x00pci into a
separate module. This makes it possible to use that
code even if PCI support is disabled. The affected
functions are used by all of the rt2x00 PCI drivers
so select the new module for those drivers.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/1128840
It appears that when this register read fails it never recovers, so
I think there is no need to repeat the same error message ad infinitum.
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Cc: users@rt2x00.serialmonkey.com
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_complete_reset will not be called if ath9k_hw_reset
is unsuccessful, so we need to re-enable intertupts to
balence the previous ath_prepare_reset call. Also schedule a
reset as a best effort method to recover the chip from
whatever state caused the channel change failure.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=55771
Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nvram contains critical initialization parameter for firmware to run. Host
driver should not proceed if nvram fails to be downloaded to dongle.
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Reviewed-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Franky Lin <frankyl@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When multiple cipher suites have been programmed then the lowest
suite is to be retured. This fixes issue when AP mode is using
CCMP and TKIP WPA combination where rekeying will fail.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
on stop_ap the dongle was not properly shutdown. As a result it was
not possible to restart AP or STA after AP operation without
restarting the device. This patch will fix that.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx and rx michael tkip keys are always swapped in case being
configured per mac. This is wrong for AP. The swap should only
be done for STA mode.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Piotr Haber <phaber@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We are waiting on first scan command of internal scan request
before association, so we should complete on last internal scan
command response.
Cc: <stable@vger.kernel.org> # 3.8
Tested-by: Daniel Drake <dsd@laptop.org>
Tested-by: Marco Cesarano <marco@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These patches modify the common probe routine to recognize the RTL8188EE
chip and implement asynchronous firmware reading in the callback routine
to initialize the sw variables.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch combines the remaining changes in the rtlwifi family to handle
the addition of rtl8188ee. A number of these changes eliminate some CamelCase
variable names, and other shorten common variable names so that long lines
in the new driver could be shortened.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In commit a5ffbe0, some of the calls to rtl_lps_leave() were switched
to be called from a work queue to avoid a scheduling while atomic bug.
This patch converts the remaining calls to use the work queue. In
addition, the call to rtl_lps_enter() is also switched to the work
queue. None of these newly converted calls had triggered the bug (yet),
but this change make all of them fit a single pattern.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These changes add the new variables for P2P and modify the various struct
definitions for other new features.
This patch updates files base.{c,h} for the changes in the newest vendor
driver.
This patch updates files ps.{c,h} for the changes in the newest vendor
driver.
This patch updates files debug.{c,h}, efuse.c, pci.{c,h}, and wifi.h for
the changes in the newest vendor driver.
This patch updates files core.c, ps.c, rc.c, and wifi.h for
the changes in the newest vendor driver.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: jcheung@suse.com
Cc: machen@suse.com
Cc: mmarek@suse.cz
Cc: zhiyuan_yang@realsil.com.cn
Cc: page_he@realsil.com.cn
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'rt2800_validate_eeprom' function uses the type of
the RT chipset for verifying the number of RX streams
on RT28x0 devices. However the type of the RT chipset
is not yet detected when the 'rt2800_validate_eeprom'
function is called.
Move the RT chipset detection code into a separate helper
function, and call it before rt2800_validate_eeprom.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the newly introduced rt2x00_set_{rf,rt} helpers
to set the RT and RF chipset separately.
This change makes it possible to move the RT
detection code into another function which will
be done in a subseqent patch.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new helpers can be used to set the type of the
RT and RF chipsets separately.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes some sparse warnings.
b43_nphy_set_rxantenna() was not used anywhere.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Newer 11ac enabled chipsets have more TX and RX buffers in FW
and hardware; so they may support larger TX and RX window sizes
for BA. Reset BA settings during association, adhoc join/start
or start_ap() if we are joining/creating 11ac network.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Sagar Bijwe <bsagar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an issue where RX throughput values observed
were substantially lower than TX counterparts for PCIe8897 STA.
PCIe8897 supports larger rx_win_size. After changing these values
we see big improvement for TX and RX throughput values.
Different tx_win_size and rx_win_size are used for AP mode.
All BA setup related initialization has been moved to separate
function.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Sagar Bijwe <bsagar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Limit the channel number in scan request, or the driver scan
config structure memory will be overflowed.
Cc: <stable@vger.kernel.org> # 3.5+
Signed-off-by: Stone Piao <piaoyun@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
net/mac80211/sta_info.c
net/wireless/core.h
Two minor conflicts in wireless. Overlapping additions of extern
declarations in net/wireless/core.h and a bug fix overlapping with
the addition of a boolean parameter to __ieee80211_key_free().
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Romosan reported that since the mac80211 changes in
"mac80211: start auth/assoc timeout on frame status" and
the subsequent fixes in "mac80211: fix auth/assoc timeout
handling" (commits 1672c0e319 and 89afe614c0) there's
sometimes an issue connecting to a 5 GHz network with the
iwlwifi DVM driver.
The reason appears to be that since these commits any bad
TX status makes mac80211 immediately try again, causing
all of the authentication attempts to be quickly rejected
by the firmware as it hasn't heard a beacon yet. Before,
it would wait for the timeout regardless of status.
To fix this, invoke the passive-no-RX workaround when not
associated yet as well. This will cause the first frame
to get lost, but then the driver will stop the queues and
the second attempt will only be transmitted after hearing
a beacon, thus delaying it appropriately to not make the
firmware reject it again.
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Tested-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a new constant ETH_P_802_3_MIN, the minimum ethernet type for
an 802.3 frame. Frames with a lower value in the ethernet type field
are Ethernet II.
Also update all the users of this value that David Miller and
I could find to use the new constant.
Also correct a bug in util.c. The comparison with ETH_P_802_3_MIN
should be >= not >.
As suggested by Jesse Gross.
Compile tested only.
Cc: David Miller <davem@davemloft.net>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Bart De Schuymer <bart.de.schuymer@pandora.be>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: linux-bluetooth@vger.kernel.org
Cc: netfilter-devel@vger.kernel.org
Cc: bridge@lists.linux-foundation.org
Cc: linux-wireless@vger.kernel.org
Cc: linux1394-devel@lists.sourceforge.net
Cc: linux-media@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: dev@openvswitch.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the following functions:
si_pmu_chipcontrol() => bcma_chipco_chipctl_maskset()
si_pmu_regcontrol() => bcma_chipco_regctl_maskset()
si_pmu_pllcontrol() => bcma_chipco_pll_maskset()
si_pmu_pllupd() => bcma_cc_set32()
si_pmu_alp_clock() => bcma_chipco_get_alp_clock()
This also removed the sih member from struct shared_phy.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The messages are currently hard coding "1ms", which does not match
the actual timeout being used.
Signed-off-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marco Fonseca reported a issue with his carl9170 device:
"I'm seeing a problem with the carl driver. If I change channels
repeatedly on the 2.4ghz band, monitoring (e.g. tcpdump) will
eventually halt. I've seen this on various versions of the carl
driver/firmware (both from 1.9.4 to 1.9.7)"
<http://marc.info/?l=linux-wireless&m=136381302428113>
The culprit was identified as "fast channel change feature" which
according to Adrian Chadd is: "... notoriously unreliable and
really only fully debugged on some very later chips."
<http://marc.info/?l=linux-wireless&m=136416984531380>
Therefore, this patch removes the fast channel change feature.
The phy will now always have to go through a cold reset when
changing channels, but it should no longer become deaf.
Cc: Marco Fonseca <marco@tampabay.rr.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix settings not being applied when the device is idle and the firmware
gets reloaded (because of changing from STA to AP mode). This caused
the device using the wrong channel (and likely band), e.g. a 5 GHz only
card still defaulted to channel 6 in the 2.4 GHz band when left
unconfigured.
This issue was always present, but only made visible with "mwl8k: Do not
call mwl8k_cmd_set_rf_channel unconditionally" (0f4316b9), since before
that the channel was (re-)configured at the next _config call even when
it did not change from the mac80211 perspective.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is possible to configure the ucode to automatically send the probe
responses to the clients after they send a probe request. At least for
WPS the userspace needs to answer the probe requests and we do not know
a way to say to the ucode to just handle the normal probe requests, so
for now no probe requests should be handled by the ucode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ucode is able to answer probe response by itself. This writes such
a template into the specific memory. Currently the probe requests are
also send to mac80211 so there are more answers send to a requesting
client. We have to make the ucode stop sending probe requests to the
driver.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To send the correct probe response the hardware needs to know the SSID
when it changed.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible that a beacon template provided by mac80211 is
written to the hardware for constant beaconing.
This is based on an old version of brcmsmac, on b43 and the spec b43 is
based on.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make brcms_c_set_beacon_period() write the beacon period to the
hardware if a new one is set.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was a read only member, replace it with pub->up.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was a read only member. The checks using BSS are replaced by
better fitting checks of the new type member.
The change in brcms_c_tbtt() was based on code from b43, in
brcms_c_ps_allowed() the same happens with BSS being true or false,
beaconing and probe responses are just needed in ap mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it possible to easily check in which mode the device is
currently running. This also adds a function to start station mode.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
setting the tsf is needed to start a timer to make beaconing in AP mode
work.
This is based on older versions of brcmsmac and b43.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of defining the magic values in the code use constants.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
FW can be woken up even by accessing device registers; we need
not explicitily enable interrupts for doing this. Future PCIe
devices will not be woken up by writing to host registers.
This patch enables driver to wake up device by reading FW status
register.
Also devices with sleep cookie enabled need some more time before
proceeding with processing. Handle this by adding a delay loop.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have received interrupt from device means FW is not sleeping.
In this case make sure wakeup handler for PCIe is not invoked by
setting adapter->pm_wakeup_fw_try to false.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling PCIe host interrupt may accidently wake up the card
when it's in sleep.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 6236dc2e2 ("brcmsmac: remove some redundant chip common workarounds")
removed the last uses.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The spectral data provided via relay-fs introduces a buffering
latency given by the subbuf_size. To meet the requirements for
delay-sensitive applications (like real-time spectral plotter),
reduce subbuf_size and increase n_subbufs.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When calculating "offset" for final RSSI calibration we're using numbers
bigger than s8 can hold. We have for example:
offset[j] = 232 - poll_results[j];
formula. If poll_results[j] is small enough (it usually is) we treat
number's bit as a sign bit. For example 232 - 1 becomes:
0xE8 - 0x1 = 0xE7, which is not 231 but -25.
This code was introduced in e0c9a0219a
and caused stability regression on some cards, for ex. BCM4322.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
il4965_rs_initialize_lq checks to see if sta is null, however, before that
check il4965_rs_use_green dereferences sta when intializing use_green.
Avoid a potential null pointer dereference error by only calling
il4965_rs_use_green after we are sure sta is not null.
Smatch analysis:
drivers/net/wireless/iwlegacy/4965-rs.c:2160 il4965_rs_initialize_lq() warn:
variable dereferenced before check 'sta' (see line 2155)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The following issue was reported.
WARNING: at net/mac80211/util.c:599 ieee80211_can_queue_work.isra.7+0x32/0x40 [mac80211]()
Hardware name: iMac12,1
queueing ieee80211 work while going to suspend
Pid: 0, comm: swapper/0 Tainted: PF O 3.8.2-206.fc18.x86_64 #1
Call Trace: Mar 16 09:39:17 Parags-iMac kernel: [ 3993.642992] <IRQ>
[<ffffffff8105e61f>] warn_slowpath_common+0x7f/0xc0
[<ffffffffa0581420>] ? ath_start_rx_poll+0x70/0x70 [ath9k]
<ffffffff8105e716>] warn_slowpath_fmt+0x46/0x50
[<ffffffffa045b542>] ieee80211_can_queue_work.isra.7+0x32/0x40
Fix this by avoiding to queue the work if our device has
already been marked as suspended or stopped.
Reported-by: Parag Warudkar <parag.lkml@gmail.com>
Tested-by: Parag Warudkar <parag.lkml@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Intermittently, b43 will report "Out of order TX status report on DMA ring".
When this happens, the driver must be reset before communication can resume.
The cause of the problem is believed to be an error in the closed-source
firmware; however, all versions of the firmware are affected.
This change uses the observation that the expected status is always 2 less
than the observed value, and supplies a fake status report to skip one
header/data pair.
Not all devices suffer from this problem, but it can occur several times
per second under heavy load. As each occurence kills the unmodified driver,
this patch makes if possible for the affected devices to function. The patch
logs only the first instance of the reset operation to prevent spamming
the logs.
Tested-by: Chris Vine <chris@cvine.freeserve.co.uk>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're using "mind" variable to find the VCM that got the best polling
results. For each VCM we calculte "currd" which is compared to the
"mind". For PHY rev3+ "currd" gets values around 14k-40k. Looking for a
value smaller than 40 makes no sense, so increase the initial value.
This fixes a regression introduced in 3.4 by commit:
e0c9a0219a
(my BCM4322 performance dropped from 18,4Mb/s to 9,26Mb/s)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes Berg