Since we are going to allow building the driver without eswitch support,
it would be possible to compile out the sriov netdevice ops struct such
that the basic ops instance will be used for non VF devices too.
Add missing udp tunnel ndos into mlx5e_netdev_ops_basic.
While here, rearrange some ndos in the sriov ops struct and put
vf/eswitch related ndos towards the end of it.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Before the GMAC on the Anarion chip can be used, the PHY interface
selection must be configured with the DWMAC block in reset.
This layer covers a block containing only two registers. Although it
is possible to model this as a reset controller and use the "resets"
property of stmmac, it's much more intuitive to include this in the
glue layer instead.
At this time only RGMII is supported, because it is the only mode
which has been validated hardware-wise.
Signed-off-by: Alexandru Gagniuc <alex.g@adaptrum.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With new transparent VF support, it is possible to get a deadlock
when some of the deferred work is running and the unregister_vf
is trying to cancel the work element. The solution is to use
trylock and reschedule (similar to bonding and team device).
Reported-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Fixes: 0c195567a8 ("netvsc: transparent VF management")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using Broadcom Systemport device in 32bit Platform, ifconfig can
only report up to 4G tx,rx status, which will be wrapped to 0 when the
number of incoming or outgoing packets exceeds 4G, only taking
around 2 hours in busy network environment (such as streaming).
Therefore, it makes hard for network diagnostic tool to get reliable
statistical result, so the patch is used to add 64bit support for
Broadcom Systemport device in 32bit Platform.
This patch provides 64bit statistics capability on both ethtool and ifconfig.
Signed-off-by: Jianming.qiao <kiki-good@hotmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving PF module param console_bitmask to lio_main.c for consistency.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's supposed to be a one-to-one correspondence between the 18 macros
that #define the OCT_DEV states (in octeon_device.h) and the strings in the
oct_dev_state_str array, but there are only 14 strings in the array.
Add the missing strings (so they become 18 in total), and also revise some
incorrect/outdated text of existing strings.
Signed-off-by: Intiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for SFP hotpluggable modules via sfp-bus and phylink.
This supports both copper and optical SFP modules, which require
different Serdes modes in order to properly negotiate the link.
Optical SFP modules typically require the Serdes link to be talking
1000BaseX mode - this is the gigabit ethernet mode defined by the
802.3 standard.
Copper SFP modules typically integrate a PHY in the module to convert
from Serdes to copper, and the PHY will be configured by the vendor
to either present a 1000BaseX Serdes link (for fixed 1000BaseT) or a
SGMII Serdes link. However, this is vendor defined, so we instead
detect the PHY, switch the link to SGMII mode, and use traditional
PHY based negotiation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in-band autonegotation support for 10GBase-KR mode.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading and writing the clause 45 MII registers.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reading module EEPROMs through phylink.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link between the ethernet MAC and its PHY has become more complex
as the interface evolves. This is especially true with serdes links,
where the part of the PHY is effectively integrated into the MAC.
Serdes links can be connected to a variety of devices, including SFF
modules soldered down onto the board with the MAC, a SFP cage with
a hotpluggable SFP module which may contain a PHY or directly modulate
the serdes signals onto optical media with or without a PHY, or even
a classical PHY connection.
Moreover, the negotiation information on serdes links comes in two
varieties - SGMII mode, where the PHY provides its speed/duplex/flow
control information to the MAC, and 1000base-X mode where both ends
exchange their abilities and each resolve the link capabilities.
This means we need a more flexible means to support these arrangements,
particularly with the hotpluggable nature of SFP, where the PHY can
be attached or detached after the network device has been brought up.
Ethtool information can come from multiple sources:
- we may have a PHY operating in either SGMII or 1000base-X mode, in
which case we take ethtool/mii data directly from the PHY.
- we may have a optical SFP module without a PHY, with the MAC
operating in 1000base-X mode - the ethtool/mii data needs to come
from the MAC.
- we may have a copper SFP module with a PHY whic can't be accessed,
which means we need to take ethtool/mii data from the MAC.
Phylink aims to solve this by providing an intermediary between the
MAC and PHY, providing a safe way for PHYs to be hotplugged, and
allowing a SFP driver to reconfigure the serdes connection.
Phylink also takes over support of fixed link connections, where the
speed/duplex/flow control are fixed, but link status may be controlled
by a GPIO signal. By avoiding the fixed-phy implementation, phylink
can provide a faster response to link events: fixed-phy has to wait for
phylib to operate its state machine, which can take several seconds.
In comparison, phylink takes milliseconds.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
- remove sync status
- rework supported and advertisment handling
- add 1000base-x speed for fixed links
- use functionality exported from phy-core, reworking
__phylink_ethtool_ksettings_set for it
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an I2C MDIO bus bridge library, to allow phylib to access PHYs which
are connected to an I2C bus instead of the more conventional MDIO bus.
Such PHYs can be found in SFP adapters and SFF modules.
Since PHYs appear at I2C bus address 0x40..0x5f, and 0x50/0x51 are
reserved for SFP EEPROMs/diagnostics, we must not allow the MDIO bus
to access these I2C addresses.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phylink will need phy_start_machine exported, so lets export it as a
GPL symbol. Documentation/networking/phy.txt indicates that this
should be a PHY API function.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sometimes, we need to do additional work between the PHY coming up and
marking the carrier present - for example, we may need to wait for the
PHY to MAC link to finish negotiation. This changes phylib to provide
a notification function pointer which avoids the built-in
netif_carrier_on() and netif_carrier_off() functions.
Standard ->adjust_link functionality is provided by hooking a helper
into the new ->phy_link_change method.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing 1000Base-X entry to the phy settings table. This was
not included because the original code could not cope with more than
32 bits of link mode mask.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_lookup_setting() provides useful functionality in ethtool code
outside phylib. Move it to phy-core and allow it to be re-used (eg,
in phylink) rather than duplicated elsewhere. Note that this supports
the larger linkmode space.
As we move the phy settings table, we also need to move the guts of
phy_supported_speeds() as well.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Other code would like to make use of this, so make the speed and duplex
string generation visible, and place it in a separate file.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the phy settings table to support more than 32 link modes by
switching to the ethtool link mode bit number representation, rather
than storing the mask. This will allow phylink and other ethtool
code to share the settings table to look up settings.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for GRO (generic receive offload) for aQuantia Atlantic driver.
This results in a perfomance improvement when GRO is enabled.
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rest of the helpers are named tcf_exts_*, so change the name of
the action number helpers to be aligned. While at it, change to inline
functions.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the __udivdi3 undefined error reported by
test robot.
Fixes: b8c17f7088 ("net: hns: Add self-adaptive interrupt coalesce support in hns driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was supposed to be a bitwise OR but there is a || vs | typo.
Fixes: 864dc729d5 ("net: phy: marvell: Refactor m88e1121 RGMII delay configuration")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prepare the datapath for refcounted ubuf_info. Clone ubuf_info with
skb_zerocopy_clone() wherever needed due to skb split, merge, resize
or clone.
Split skb_orphan_frags into two variants. The split, merge, .. paths
support reference counted zerocopy buffers, so do not do a deep copy.
Add skb_orphan_frags_rx for paths that may loop packets to receive
sockets. That is not allowed, as it may cause unbounded latency.
Deep copy all zerocopy copy buffers, ref-counted or not, in this path.
The exact locations to modify were chosen by exhaustively searching
through all code that might modify skb_frag references and/or the
the SKBTX_DEV_ZEROCOPY tx_flags bit.
The changes err on the safe side, in two ways.
(1) legacy ubuf_info paths virtio and tap are not modified. They keep
a 1:1 ubuf_info to sk_buff relationship. Calls to skb_orphan_frags
still call skb_copy_ubufs and thus copy frags in this case.
(2) not all copies deep in the stack are addressed yet. skb_shift,
skb_split and skb_try_coalesce can be refined to avoid copying.
These are not in the hot path and this patch is hairy enough as
is, so that is left for future refinement.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now have all the necessary IPv6 infrastructure in place, so stop
ignoring these notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without resorting to ACLs, the device performs route lookup solely based
on the destination IP address.
In case source-specific routing is needed, an error is returned and the
abort mechanism is activated, thus allowing the kernel to take over
forwarding decisions.
Instead of aborting, we can trap specific destination prefixes where
source-specific routes are present, but this will result in a lot more
code that is unlikely to ever be used.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we got a replace event, then the replaced route must exist. If
the route isn't capable of multipath, then replace first matching
non-multipath capable route.
If the route is capable of multipath and matching multipath capable
route is found, then replace it. Otherwise, replace first matching
non-multipath capable route.
The new route is inserted before the replaced one. In case the replaced
route is currently offloaded, then it's overwritten in the device's table
by the new route and later deleted, thus not impacting routed traffic.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow directly connected and remote unicast IPv6 routes to be programmed
to the device's tables.
As with IPv4, identical routes - sharing the same destination prefix -
are ordered in a FIB node according to their table ID and then the
metric. While the kernel doesn't share the same trie for the local and
main table, this does happen in the device, so ordering according to
table ID is needed.
Since individual nexthops can be added and deleted in IPv6, each FIB
entry stores a linked list of the rt6_info structs it represents. Upon
the addition or deletion of a nexthop, a new nexthop group is allocated
according to the new configuration and the old one is destroyed.
Identical groups aren't currently consolidated, but will be in a
follow-up patchset.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We only allow FIB offload in the presence of default rules or an l3mdev
rule. In a similar fashion to IPv4 FIB rules, sanitize IPv6 rules.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification block currently only handles IPv4 events, but we
want to start handling IPv6 events soon, so lay the groundwork now.
Do that by preparing the work item and process it according to the
notified address family.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As in previous patch, ignore IPv6 notifications since the driver doesn't
support these.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to add IPv6 notifications in the FIB notification chain, but
the driver currently doesn't support these, so ignore them.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FIB notification chain is currently soley used by IPv4 code.
However, we're going to introduce IPv6 FIB offload support, which
requires these notification as well.
As explained in commit c3852ef7f2 ("ipv4: fib: Replay events when
registering FIB notifier"), upon registration to the chain, the callee
receives a full dump of the FIB tables and rules by traversing all the
net namespaces. The integrity of the dump is ensured by a per-namespace
sequence counter that is incremented whenever a change to the tables or
rules occurs.
In order to allow more address families to use the chain, each family is
expected to register its fib_notifier_ops in its pernet init. These
operations allow the common code to read the family's sequence counter
as well as dump its tables and rules in the given net namespace.
Additionally, a 'family' parameter is added to sent notifications, so
that listeners could distinguish between the different families.
Implement the common code that allows listeners to register to the chain
and for address families to register their fib_notifier_ops. Subsequent
patches will implement these operations in IPv6.
In the future, ipmr and ip6mr will be extended to provide these
notifications as well.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds the support for two related features:
- Support for TX interrupts, with one interrupt for each CPU
- Support for different RX queue distribution modes
MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
per-CPU interrupts used for TX events are also used for RX events.
Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.
This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".
For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).
In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).
Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.
For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.
The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This operation is required for handling ioctl commands like SIOCGMIIREG,
when debugging MDIO registers from userspace.
This commit adds support for this operation.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the MAINTAINERS file with HNS3 Ethernet driver
maintainers names and other details. This also introduces the new
Makefiles required to build the HNS3 Ethernet driver and updates
the existing Kconfig file in the hisilicon folder.
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the Ethtool interface to
the HNS3 Ethernet driver. Various commands to read the
statistics, configure the offloading, loopback selftest etc.
are supported.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of MDIO bus interface for HNS3 driver.
Code provides various interfaces to start and stop the PHY layer
and to read and write the MDIO bus or PHY.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
THis patch adds the support of the Scheduling and Shaping
functionalities during the transmit leg. This also adds the
support of Pause at MAC level. (Pause at per-priority level
shall be added later along with the DCB feature).
Hardware as such consists of two types of cofiguration of 6 level
schedulers. Algorithms varies according to the level and type
of scheduler being used. Current patch is used to initialize
the mapping, algorithms(like SP, DWRR etc) and shaper(CIR, PIR etc)
being used.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of Hisilicon Network Subsystem Accceleration
Engine and common operations to access it. This layer provides access to the
hardware configuration, hardware statistics. This layer is also
responsible for triggering the initialization of the PHY layer through
the below MDIO layer.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of IMP (Integrated Management Processor)
command interface to the HNS3 driver.
Each PF/VF has support of CQP(Command Queue Pair) ring interface.
Each CQP consis of send queue CSQ and receive queue CRQ.
There are various commands a PF/VF may support, like for Flow Table
manipulation, Device management, Packet buffer allocation, Forwarding,
VLANs config, Tunneling/Overlays etc.
This patch contains code to initialize the command queue, manage the
command queue descriptors and Rx/Tx protocol with the command processor
in the form of various commands/results and acknowledgements.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of the HNAE3 (Hisilicon Network
Acceleration Engine 3) framework support to the HNS3 driver.
Framework facilitates clients like ENET(HNS3 Ethernet Driver), RoCE
and user-space Ethernet drivers (like ODP etc.) to register with HNAE3
devices and their associated operations.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the support of Hisilicon Network Subsystem 3
Ethernet driver to hip08 family of SoCs.
This driver includes basic Rx/Tx functionality. It also includes
the client registration code with the HNAE3(Hisilicon Network
Acceleration Engine 3) framework.
This work provides the initial support to the hip08 SoC and
would incrementally add features or enhancements.
Signed-off-by: Daode Huang <huangdaode@hisilicon.com>
Signed-off-by: lipeng <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Wei Hu (Xavier) <xavier.huwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_channels (ethtool -l) functionality
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement .get_ringparam (ethtool -g) functionality
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vnic server reports the statistics buffer in big endian format and must
be converted to cpu endian in order to be displayed correctly on little
endian lpars.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add counters to report number of packets, bytes, and dropped packets for
each transmit queue and number of packets, bytes, and interrupts for each
receive queue. Modify ethtool callbacks to report the new statistics.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been a while now since ds->dst is not an array anymore, but a
simple pointer to a dsa_switch_tree.
Fortunately, SF2 does not support multi-chip and thus ds->index is
always 0.
This patch substitutes 'ds->dst[ds->index].' with 'ds->dst->'.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const to bin_attribute structure as it is only passed to the
functions sysfs_{remove/create}_bin_file. The corresponding
arguments are of type const, so declare the structure to be const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When deal with low and high throughput, it is hard to achiece both
high performance and low latency. In order to achiece that, this patch
calculates the rx rate, and adjust the interrupt coalesce parameter
accordingly.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Tested-by: Weiwei Deng <dengweiwei@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Dell Wireless 1802 card as an AR9462 in the ath9k pci list.
Note that the wowlan feature is supported and has been tested
successfully.
Signed-off by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes a trivial debugfs file permission issue. Debugfs
file ack_to has no write function, so S_IWUSR gets purged.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
WMI interface for all the firmwares(except QCA6174) does not include the
type of peer(default/bss/tdls) requested during peer creation, therefore
target creates a default peer.
TDLS implementation on 10.4 firmware requires host to configure the
peer type(tdls) for TDLS peers. This patch adds peer type parameter to the
existing WMI interface for peer creation to accommodate this requirement.
Tested this change on QCA9888(10.4-3.5.1-00018) and QCA988x(10.2.4.70.9-2)
with ping tests for AP/STA modes.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch adds the support of TDLS feature for 10.4 firmware
versions.
A new WMI service is added to advertise the support of TDLS for
10.4 firmwares.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Though there is room to accommodate 512 services in wmi service
ready event, target uses only first 4-bits of each 32-bit word for
advertising wmi services thereby limiting max wmi services to 64.
TDLS implementation for 10.4 firmwares introduces new wmi services by
making use of remaining unused bits of each 32-bit word, therefore the
wmi service mapping in host needs to be extended.
This patch adds the logic to extend the wmi SVCMAP to accommodate new
wmi services.
Signed-off-by: Manikanta Pubbisetty <mpubbise@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
As suggested by Arnd Bergmann, replace
"while (time_before_...) {}"
with
"do {} while (time_before_...)"
This fixes the following warnings detected by gcc 4.1.2:
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_mbox_rxmsg_pending_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:676: warning: ‘ret’ may be used uninitialized in this function
...
drivers/net/wireless/ath/ath10k/sdio.c: In function
‘ath10k_sdio_irq_handler’:
drivers/net/wireless/ath/ath10k/sdio.c:1331: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Chipsets like QCA9377 have support for USB so add initial USB bus
support to ath10k. With this patch we have the low level HIF and
HTC protocol working and it's possible to boot the firmware,
but it's still not possible to connect or anything like.
More changes are needed for full functionality. For that reason
we print during initialisation:
WARNING: ath10k USB support is incomplete, don't expect anything to work!
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Set the a-mpdu reference number in ath10k to make it accessible in the
receivers radiotap header. Implemented as in ath9k. The reference number is
needed for troubleshooting and research at the receivers site (e.g. to identify
mpdu's that were aggregated in an a-mpdu)
Signed-off-by: Matthias Frei <mf@frei.media>
[kvalo@qca.qualcomm.com: fix checkpatch warning, commit log cleanup]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In _rtl_init_mac80211(), hardcoded value for hw->max_listen_interval
and hw->max_rate_tries are replaced by macro and removed the comment.
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes, we might using wifi-only firmware with a combo firmware name,
in this case, do not need to filter bluetooth part from header.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
uninitilized variable, such as .add_req_result might be magic stack
value. Initialize the structure to make it clean.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After commit cf124db566 ("net: Fix inconsistent teardown and
release of private netdev state."), setting
'dev->needs_free_netdev' ensures device data is released, and
'dev->destructor' is not used anymore.
Fixes: cf124db566 ("net: Fix inconsistent teardown and release of private netdev state.")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
1899 928 0 2827 b0b realtek/rtlwifi/rtl8192ee/sw.o
File size After adding 'const':
text data bss dec hex filename
1963 864 0 2827 b0b realtek/rtlwifi/rtl8192ee/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3090 912 0 4002 fa2 realtek/rtlwifi/rtl8188ee/sw.o
File size After adding 'const':
text data bss dec hex filename
3154 848 0 4002 fa2 realtek/rtlwifi/rtl8188ee/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
3032 912 0 3944 f68 realtek/rtlwifi/rtl8723be/sw.o
File size After adding 'const':
text data bss dec hex filename
3096 848 0 3944 f68 realtek/rtlwifi/rtl8723be/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2775 912 0 3687 e67 realtek/rtlwifi/rtl8723ae/sw.o
File size After adding 'const':
text data bss dec hex filename
2839 848 0 3687 e67 realtek/rtlwifi/rtl8723ae/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2491 960 0 3451 d7b realtek/rtlwifi/rtl8821ae/sw.o
File size After adding 'const':
text data bss dec hex filename
2587 864 0 3451 d7b realtek/rtlwifi/rtl8821ae/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2817 1040 0 3857 f11 realtek/rtlwifi/rtl8192se/sw.o
File size After adding 'const':
text data bss dec hex filename
3009 848 0 3857 f11 realtek/rtlwifi/rtl8192se/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pci_device_id are not supposed to change at runtime. All functions
working with pci_device_id provided by <linux/pci.h> work with
const pci_device_id. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
2833 945 12 3790 ece realtek/rtlwifi/rtl8192de/sw.o
File size After adding 'const':
text data bss dec hex filename
2929 849 12 3790 ece realtek/rtlwifi/rtl8192de/sw.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As the only caller of dma_supported() outside of DMA API internals, the
qtfnmac driver stands out and invites scrutiny. Thankfully, it's not
being used for evil, but it is entirely redundant, since it open-codes a
check that the DMA mask setting functions are going to perform anyway.
In fact, the whole qtnf_pcie_init_dma_mask() function is nothing more
than a rather long-winded implementation of dma_set_mask_and_coherent(),
so let's just use that directly.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modify qlink command structures and interface types handling
to prepare adding AP_VLAN support to qtnfmac driver.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function is not used anymore, so remove it.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware sends supported interface type rather than mask. As a result,
types field of ieee80211_iface_limit structure may end up having
multiple iftype bits set. This leads to WARN_ON from
wiphy_verify_combinations.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Userspace tools may hang on scan in the case when scan completion event
is not returned by firmware. This patch implements the scan timeout
to avoid such situation.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch implements cfg80211 channel_switch handler enabling CSA
channel-switch procedure.
Driver performs only basic validation of the requested new channel
and then sends command to firmware. Beacon IEs are not sent since
beacon update is handled by firmware.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless cfg80211 core supplies channel settings in cfg80211_ap_settings
structure for each BSS in multiple BSS configuration. On the other hand
all the virtual interfaces on one radio are using the same PHY settings
including channel.
Move chandef structure from vif to mac structure in order to mantain
the only instance of cfg80211_chan_def structure in qtnf_wmac
rather than its multiple copies in qtnf_vif.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use proper endianness conversion for client station leave reason.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement current channel reporting functionality. Current operating
channel can be obtained either directly using cfg80211 get_channel
callback or from stats reported by cfg80211 survey_dump callback.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add missing bus lock into get_mac_chan_info command.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Regdomain information needs to be registered with cfg80211
for devices with REGULATORY_WIPHY_SELF_MANAGED flag set.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On startup driver obtains regulatory rules from firmware and
enables them during wiphy registration. Later on regulatory
domain change can be requested by host. In this case firmware
is notified about the upcoming changes. If the change is valid,
then firmware updates hardware channel configuration and host
driver receives updated channel info for each band.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Avinash Patil <avinashp@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit f70e4df2b3 ("rtlwifi: Add code to read new versions of
firmware") added code to load an old firmware file if the new one is
not available. Unfortunately that code is never reached because
request_firmware_nowait() does not wait for the firmware to show up
and returns 0 even if the file is not there.
Use the existing fallback mechanism introduced by commit 62009b7f12
("rtlwifi: rtl8192cu: Add new firmware") instead.
Fixes: f70e4df2b3 ("rtlwifi: Add code to read new versions of firmware")
Cc: stable@vger.kernel.org
Signed-off-by: Sven Joachim <svenjoac@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that some IEs get missed during association.
This patch correct the old IE parse code. sme->ie will be
store as wpa ie, wps ie, wapi ie and gen ie accordingly.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
_rtl_pci_find_adapter fail path will jump to label fail3 for
unsupported adapter types.
However, on course for fail3 there will be call rtl_deinit_core
before rtl_init_core.
For the inclusion of checking pci_iounmap this fail can be moved to
fail2.
Fixes
[ 4.492963] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 4.493067] IP: rtl_deinit_core+0x31/0x90 [rtlwifi]
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Now that we provide offload indication using the nexthop's flags we must
refresh the offload indication whenever the offload state within the
group changes.
This didn't matter until now, as offload indication was provided using
the FIB info flags and multipath routes were marked as offloaded as long
as one of the nexthops was offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous patch removed the reliance on the counter in the FIB info to
set the offload indication, so we no longer need to keep an offload
state on each FIB entry and can just set or unset the RTNH_F_OFFLOAD
flag in each nexthop.
This is also necessary because we're going to need to refresh the
offload indication whenever the nexthop group associated with the FIB
entry is refreshed. Current check would prevent us from marking a newly
resolved nexthop as offloaded if the FIB entry is already marked as
offloaded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a similar fashion to previous patch, use the nexthop flags to provide
offload indication instead of the FIB info's flags.
In case a nexthop in a multipath route can't be offloaded (gateway's MAC
can't be resolved, for example), then its offload flag isn't set.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to stop using the FIB info's flags to provide the offlaod
indication and instead do that on a per-nexthop basis.
Convert rocker to do just that. It only supports one nexthop per-route,
so conversion is simple.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'trans->tid' is only assigned later in the function, resulting in a zero
transaction ID. Use 'tid' instead.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements transparent fail over from synthetic NIC to
SR-IOV virtual function NIC in Hyper-V environment. It is a better
alternative to using bonding as is done now. Instead, the receive and
transmit fail over is done internally inside the driver.
Using bonding driver has lots of issues because it depends on the
script being run early enough in the boot process and with sufficient
information to make the association. This patch moves all that
functionality into the kernel.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file /sys/devices/pci000.../sriov_totalvfs is showing a wrong value.
Fix it by calling pci_sriov_set_totalvfs() to set the total number of VFs
available after calculations for the number of PF and VF queues are made.
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last patch added the dependency on 'OF && HAS_IOMEM' but left
COMPILE_TEST as an alternative, which kind of defeats the purpose
of adding the dependency, we still get randconfig build warnings:
warning: (NET_DSA_BCM_SF2 && BCMGENET) selects MDIO_BCM_UNIMAC which has unmet direct dependencies (NETDEVICES && MDIO_BUS && HAS_IOMEM && OF_MDIO)
For compile-testing purposes, we don't really need this anyway,
as CONFIG_OF can be enabled on all architectures, and HAS_IOMEM
is present on all architectures we do meaningful compile-testing on
(the exception being arch/um).
This makes both OF and HAS_IOMEM hard dependencies.
Fixes: 5af74bb4fc ("net: bcmgenet: Add dependency on HAS_IOMEM && OF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repeated dereference of nvmsg.msg.v1_msg.send_rndis_pkt can be
shortened by using a temporary. Do so.
No change in object code.
Miscellanea:
o Use * const for rpkt and nvchan
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the PHY EEE settings, rename the .set_eee and
.get_eee ops to respectively .set_mac_eee and .get_mac_eee.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY's EEE settings are already accessed by the DSA layer through the
Marvell PHY driver and there is nothing to be done for switch's MACs.
Remove all EEE support from the mv88e6xxx driver and simply return 0
from the EEE ops.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA switch operations for EEE are only meant to configure a port's
MAC EEE settings. The port's PHY EEE settings are accessed by the DSA
layer and must be made available via a proper PHY driver.
In order to reduce this confusion, remove the phy_device argument from
the .set_eee operation.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
All DSA drivers are calling phy_init_eee if eee_enabled is true.
Move up this statement in the DSA layer to simplify the DSA drivers.
qca8k does not require to cache the ethtool_eee structures from now on.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is safer to init the EEE before the DSA layer call
phy_ethtool_set_eee, as sf2 and qca8k are doing.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SF2 driver is masking the supported bitfield of its private copy of
the ports' ethtool_eee structures. It is used nowhere, thus remove it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
phy_ethtool_get_eee is already called by the DSA layer, thus remove the
duplicated call in the qca8k driver.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8k driver is currently caching a bitfield of the supported member
of a ethtool_eee private structure, which is unused.
Only the eee_enabled field of the private ethtool_eee copy is updated,
thus using p->advertised and p->lp_advertised is also erroneous.
Remove the usage of these private ethtool_eee members and only rely on
phy_ethtool_get_eee to assign the eee_active member.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If EEE is queried enabled, qca8k_set_eee calls qca8k_eee_enable_set
twice (because it is already called in qca8k_eee_init). Fix that.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The qca8k obviously copied code from the sf2 driver as how to set EEE:
if (e->eee_enabled) {
p->eee_enabled = qca8k_eee_init(ds, port, phydev);
if (!p->eee_enabled)
ret = -EOPNOTSUPP;
}
But it did not use the same logic for the EEE init routine, which is
"Returns 0 if EEE was not enabled, or 1 otherwise". This results in
returning -EOPNOTSUPP on success and caching EEE enabled on failure.
This patch fixes the returned value of qca8k_eee_init.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The renesas-cpg-mssr clock driver are not yet aware of PSCI sleep where
power is cut to the SoC. When resuming from this state with WoL enabled
the enable count of the ravb clock is 1 and the clock driver thinks the
clock is already on when PM core enables the clock and increments the
enable count to 2. This will result in the ravb driver failing to talk
to the hardware since the module clock is off. Work around this by
forcing the enable count to 0 and then back to 2 when resuming with WoL
enabled.
This workaround should be reverted once the renesas-cpg-mssr clock
driver becomes aware of this PSCI sleep behavior.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL is enabled in the suspend callback by setting MagicPacket detection
and disabling all interrupts expect MagicPacket. In the resume path the
driver needs to reset the hardware to rearm the WoL logic, this prevents
the driver from simply restoring the registers and to take advantage of
that ravb was not suspended to reduce resume time. To reset the
hardware the driver closes the device, sets it in reset mode and reopens
the device just like it would do in a normal suspend/resume scenario
without WoL enabled, but it both closes and opens the device in the
resume callback since the device needs to be reset for WoL to work.
One quirk needed for WoL is that the module clock needs to be prevented
from being switched off by Runtime PM. To keep the clock alive the
suspend callback need to call clk_enable() directly to increase the
usage count of the clock. Then when Runtime PM decreases the clock usage
count it won't reach 0 and be switched off.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-08-01
Here's our first batch of Bluetooth patches for the 4.14 kernel:
- Several new USB IDs for the btusb driver
- Memory leak fix in btusb driver
- Cleanups & fixes to hci_nokia, hci_serdev and hci_bcm drivers
- Fixed cleanup path in mrf24j40 (802.15.4) driver probe function
- A few other smaller cleanups & fixes to drivers
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver for ethernet controller on MT7622 SoC. It has
the similar handling logic as the previously MT7623 does, but there are
additions against with MT7623 SoC, the shared SGMII given for the dual
GMACs and including 5-ports 10/100 embedded switch support (ESW) as the
GMAC1 option, thus more clocks consumers for the extra feature are
introduced here. So for ease portability and maintenance, those
differences all are being kept inside the platform data as other drivers
usually do. Currently testing successfully is done with those patches for
the conditions such as GMAC2 with IP1001 PHY via RGMII and GMAC1/2 with
RTL8211F PHY via SGMII.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is the preparation patch in order to adapt into various
hardware through adding platform data which holds specific characteristics
among MediaTek SoCs and introducing the unified clock handler for those
distinct clock requirements depending on different features such as
TRGMII and SGMII getting support on the target SoC. And finally, add
enhancement with given the generic description for Kconfig and remove the
unnecessary machine type dependency in Makefile.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
All the firmware versions the driver supports enable DQA, and thus
the only way to get non-DQA mode is to modify the source. Remove
this mode to simplify the code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The iwl_mvm_add_bcast_sta() and the iwl_mvm_rm_bcast_sta() functions
are only called in P2P flows. Add _p2p_ to the function names to make
this explicit.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to spell out the cases when we can just
use ieee80211_is_bufferable_mmpdu().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the TXQ timer freeze code will not properly handle the
large TVQM queue numbers, warn if we get into that code when
we have TVQM. Also, just to catch this earlier, warn if the
firmware image doesn't support AP_LINK_PS but we're running
on HW using TVQM.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Rename this function to the more appropriate iwl_pcie_check_hw_rf_kill()
since it's only a function in the pcie code and cannot be called from
any other place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing purposes, we may want to disable EBS scans at compile time.
Signed-off-by: Roee Zamir <roee.zamir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During init, the FW checks whether the FSEQ value matches what it
expects. If it doesn't match, we print a warning to let integrators
clearly know that something is wrong. This can happen if another core
(i.e. not WiFi) has updated the FSEQ version. This notification is
only sent by the FW in production, for development firmwares, an
assertion is triggered instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
If the OTP is empty, the NVM_GET_INFO command returns
with flags' bit(0) on. This means the FW returns the
default values for working with. This is allowed, so
use this returned data.
Fixes: e9e1ba3dbf ("iwlwifi: mvm: support getting nvm data from firmware")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The return status check of iwl_pcie_gen2_build_amsdu
was buggy. Fix it.
Fixes: 6ffe5de35b ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While waiting for queues to empty,
If txq_id == IWL_MVM_INVALID_QUEUE for all txq_ids,
ret is used uninitialized.
Found by Klocwork.
Fixes: d6d517b773 ("iwlwifi: add wait for tx queue empty")
Signed-off-by: Sharon Dvir <sharon.dvir@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FIFO numbering is different in A000 devices. This
means that we routed BE packets to BK FIFO. Fix this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently support 3 different versions of the beacon template
command and the code does some tricks in order to reuse what is
possible across these versions. But it is a bit complicated to read
and soon there will be one more variation that the driver needs
implement, which would complicate it even further.
Refactor the way we send beacon template commands, which increases the
code size a bit, but makes it much easier to read.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Those constants have been unused for quite some time now.
Signed-off-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Convention has it to byte-swap the constant instead of the variable
when doing bit checks. This also generates better code when the swap
is actually needed, since the constant can be swapped at compile-time.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are two workarounds because RSS is currently broken on A000
devices due to firmware issues, but checking for the new TX API
doesn't really make sense. Check the hardware family instead of
the new TX API - there's nothing better to check since it's just
a temporary workaround.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This may need to be refined later, but for now using this,
even with the TODO, is better than checking "has new TX API".
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Track the current firmware image in the common code instead
of in the opmode so that later patches can access it there
in a common way.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the shared memory command parsing into common code.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactor the paging code from mvm to be used by different opmodes.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Pull networking fixes from David Miller:
1) Handle notifier registry failures properly in tun/tap driver, from
Tonghao Zhang.
2) Fix bpf verifier handling of subtraction bounds and add a testcase
for this, from Edward Cree.
3) Increase reset timeout in ftgmac100 driver, from Ben Herrenschmidt.
4) Fix use after free in prd_retire_rx_blk_timer_exired() in AF_PACKET,
from Cong Wang.
5) Fix SElinux regression due to recent UDP optimizations, from Paolo
Abeni.
6) We accidently increment IPSTATS_MIB_FRAGFAILS in the ipv6 code
paths, fix from Stefano Brivio.
7) Fix some mem leaks in dccp, from Xin Long.
8) Adjust MDIO_BUS kconfig deps to avoid build errors, from Arnd
Bergmann.
9) Mac address length check and buffer size fixes from Cong Wang.
10) Don't leak sockets in ipv6 udp early demux, from Paolo Abeni.
11) Fix return value when copy_from_user() fails in
bpf_prog_get_info_by_fd(), from Daniel Borkmann.
12) Handle PHY_HALTED properly in phy library state machine, from
Florian Fainelli.
13) Fix OOPS in fib_sync_down_dev(), from Ido Schimmel.
14) Fix truesize calculation in virtio_net which led to performance
regressions, from Michael S Tsirkin.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (76 commits)
samples/bpf: fix bpf tunnel cleanup
udp6: fix jumbogram reception
ppp: Fix a scheduling-while-atomic bug in del_chan
Revert "net: bcmgenet: Remove init parameter from bcmgenet_mii_config"
virtio_net: fix truesize for mergeable buffers
mv643xx_eth: fix of_irq_to_resource() error check
MAINTAINERS: Add more files to the PHY LIBRARY section
ipv4: fib: Fix NULL pointer deref during fib_sync_down_dev()
net: phy: Correctly process PHY_HALTED in phy_stop_machine()
sunhme: fix up GREG_STAT and GREG_IMASK register offsets
bpf: fix bpf_prog_get_info_by_fd to dump correct xlated_prog_len
tcp: avoid bogus gcc-7 array-bounds warning
net: tc35815: fix spelling mistake: "Intterrupt" -> "Interrupt"
bpf: don't indicate success when copy_from_user fails
udp6: fix socket leak on early demux
net: thunderx: Fix BGX transmit stall due to underflow
Revert "vhost: cache used event for better performance"
team: use a larger struct for mac address
net: check dev->addr_len for dev_set_mac_address()
phy: bcm-ns-usb3: fix MDIO_BUS dependency
...
The PPTP set the pptp_sock_destruct as the sock's sk_destruct, it would
trigger this bug when __sk_free is invoked in atomic context, because of
the call path pptp_sock_destruct->del_chan->synchronize_rcu.
Now move the synchronize_rcu to pptp_release from del_chan. This is the
only one case which would free the sock and need the synchronize_rcu.
The following is the panic I met with kernel 3.3.8, but this issue should
exist in current kernel too according to the codes.
BUG: scheduling while atomic
__schedule_bug+0x5e/0x64
__schedule+0x55/0x580
? ppp_unregister_channel+0x1cd5/0x1de0 [ppp_generic]
? dev_hard_start_xmit+0x423/0x530
? sch_direct_xmit+0x73/0x170
__cond_resched+0x16/0x30
_cond_resched+0x22/0x30
wait_for_common+0x18/0x110
? call_rcu_bh+0x10/0x10
wait_for_completion+0x12/0x20
wait_rcu_gp+0x34/0x40
? wait_rcu_gp+0x40/0x40
synchronize_sched+0x1e/0x20
0xf8417298
0xf8417484
? sock_queue_rcv_skb+0x109/0x130
__sk_free+0x16/0x110
? udp_queue_rcv_skb+0x1f2/0x290
sk_free+0x16/0x20
__udp4_lib_rcv+0x3b8/0x650
Signed-off-by: Gao Feng <gfree.wind@vip.163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 28b45910cc ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.
Fixes: 28b45910cc ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Doug Berger <opendmb@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seth Forshee noticed a performance degradation with some workloads.
This turns out to be due to packet drops. Euan Kemp noticed that this
is because we drop all packets where length exceeds the truesize, but
for some packets we add in extra memory without updating the truesize.
This in turn was kept around unchanged from ab7db91705 ("virtio-net:
auto-tune mergeable rx buffer size for improved performance"). That
commit had an internal reason not to account for the extra space: not
enough bits to do it. No longer true so let's account for the allocated
length exactly.
Many thanks to Seth Forshee for the report and bisecting and Euan Kemp
for debugging the issue.
Fixes: 680557cf79 ("virtio_net: rework mergeable buffer handling")
Reported-by: Euan Kemp <euan.kemp@coreos.com>
Tested-by: Euan Kemp <euan.kemp@coreos.com>
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 1116r has code to set downshift. Refactor this into a helper, so
in future other marvell PHYs can use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.
Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out that MII_M1116R_CONTROL_REG_MAC is the same as
MII_88E1121_PHY_MSCR_REG. Refactor the code to set the RGMII delays
into a shared helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated a few times. Refactor into a helped.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated for different PHY versions. Put it into a
help and call when needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using an open coded equivalent, use the core
genphy_soft_reset() function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert spaces to tabs where appropriate, and fix up some otherwise
odd indentation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Marvell MV643xx Ethernet
driver still only regards 0 as invalid IRQ -- fix it up.
Fixes: 7a4228bbff ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs CONFIG_HAS_IOMEM and OF to be functional, but we still
let it build with COMPILE_TEST. This fixes the unmet dependency after
selecting MDIO_BCM_UNIMAC in commit mentioned below:
warning: (NET_DSA_BCM_SF2 && BCMGENET) selects MDIO_BCM_UNIMAC which has
unmet direct dependencies (NETDEVICES && MDIO_DEVICE && HAS_IOMEM &&
OF_MDIO)
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marc reported that he was not getting the PHY library adjust_link()
callback function to run when calling phy_stop() + phy_disconnect()
which does not indeed happen because we set the state machine to
PHY_HALTED but we don't get to run it to process this state past that
point.
Fix this with a synchronous call to phy_state_machine() in order to have
the state machine actually act on PHY_HALTED, set the PHY device's link
down, turn the network device's carrier off and finally call the
adjust_link() function.
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Fixes: a390d1f379 ("phylib: convert state_queue work to delayed_work")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the values to match those from the STP2002QFP documentation.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, old and new PHY states are always logged.
>From now on, log only PHY state transitions.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Express the same logic more succinctly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer logical operator that expresses the intent to bitwise one that
happens to give the same result.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames IP2ME-specific registers reg_ralue_v and
reg_ralue_tunnel_ptr to reg_ralue_ip2me_*.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments really belong to the individual enumerators. The comment
at the register should instead reference the enum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_mii_init() has an error path which is strictly identical to the
unwinding that bcmgenet_mii_exit() does, so have bcmgenet_mii_init()
utilize bcmgenet_mii_exit() for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have fully migrated to the mdio-bcm-unimac driver, drop the
legacy MDIO bus code which did duplicate a fair amount of code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the GENET driver to register an UniMAC MDIO bus controller for
the GENET internal MDIO bus, update the platform data code to attach the
PHY to the correct MDIO bus controller.
The Device Tree portion of the code is mostly left unmodified since the
lookup/binding is done via phandles and Device Tree nodes which are much
more flexible in locating and binding PHYs to their respective MDIO bus
controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having the bcmgenet driver migrate over the
mdio-bcm-unimac driver, add a platform data structure which allows
passing integrating specific details like bus name, wait function to
complete MDIO operations and PHY mask.
We also define what the platform device name contract is by defining
UNIMAC_MDIO_DRV_NAME and moving it to the platform_data header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be stricly identical to what bcmgenet does, add a debug
print when a PHY workaround during bus->reset() is executed. Preliminary
change to moving bcmgenet towards mdio-bcm-unimac.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having multiple GENET instances in a system (up to
3), make sure that we do include the bus instance number in the name of
the MDIO bus such that we change it from "unimac-mdio" to
"unimac-mdio-0" for instance.
So far, the only user of this driver is using Device Tree, which uses a
lookup/parenting based technique to map PHY devices to their respective
MDIO bus controllers, hence causing no additional changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code that does the busy polling on the MDIO_BUSY bit since we
will have different code-paths for for completion depending on whether
we are using interrupts or polling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect access (PMI) to phy register only work in I2C mode. In
MDIO mode phy registers must be accessed directly. Introduced
struct lan9303_phy_ops to handle the two modes.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing for the following fix of MDIO phy access:
Renamed functions that access PHY 1 and 2 indirectly through PMI
registers.
lan9303_port_phy_reg_wait_for_completion() to
lan9303_indirect_phy_wait_for_completion()
lan9303_port_phy_reg_read() to
lan9303_indirect_phy_read()
lan9303_port_phy_reg_write() to
lan9303_indirect_phy_write()
Also changed "val" parameter of lan9303_indirect_phy_write() to u16,
for clarity.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_mdio_write()/_read() must multiply register number by 4 to get
offset.
Added some commments to the register definitions.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle that MDIO read with no response return 0xffff.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two fixes for for brcmfmac, the crash was reported by two people
already so it's a high priority fix.
brcmfmac
* fix a crash in skb headroom handling in v4.13-rc1
* fix a memory leak due to a merge error in v4.6
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZe0L2AAoJEG4XJFUm622bCiYIAKXCyEV2CCfNgloFcPmElvPR
HvmYDzxQeJVEjCYjzYLpaBK6rfJtMuBhmHfSrCTSd6YulWOUoUy6IRMi7bgoZe2C
5cccqZl3uU8fG34ib6jKvp6ofx5DX3yFMQQa0toY27VQTkY46AT6yx9UMn4Mi+bQ
p0skV/1gwf0IPGfZQkpSemhosmtEaNLNMiqAJlOQrsi2b9YYcBYTW1svnr/yB0UM
7pl0+zUVE+Ul/eJHb82JeJaRrNYLRZ7KD5bMlV9OoDO/Rlu3933fNE/+jWtuuTVG
VnNLyhEI1CR767CppOhraDVkGvINg+EewCouWQ9ZCUWxTcVuFxAew+QkI6foS2A=
=uMUa
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2017-07-28' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.13
Two fixes for for brcmfmac, the crash was reported by two people
already so it's a high priority fix.
brcmfmac
* fix a crash in skb headroom handling in v4.13-rc1
* fix a memory leak due to a merge error in v4.6
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Latency improvement related to NAPI conversion.
If all packets are processed from receive ring then need
to signal host.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting receive buffer fails, the error unwind would cause
kernel panic because it was not correctly doing RCU and NAPI
unwind. RCU'd pointer needs to be reset to NULL, and NAPI needs
to be disabled not deleted.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize how receive completion ring are managed.
* Allocate only as many slots as needed for all buffers from host
* Allocate before setting up sub channel for better error detection
* Don't need to keep copy of initial receive section message
* Precompute the watermark for when receive flushing is needed
* Replace division with conditional test
* Replace atomic per-device variable with per-channel check.
* Handle corner case where receive completion send
fails if ring buffer to host is full.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal API was passing struct hv_page_buffer **
when only simple struct hv_page_buffer * was necessary
for passing an array.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using %p to print pointer to packet meta-data doesn't give any
good info, and exposes kernel memory offsets.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes a bunch of fixups for issues reported by
lockdep.
* ethtool routines can assume RTNL
* send is done with RCU lock (and BH disable)
* avoid refetching internal device struct (netvsc)
instead pass it as a parameter.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in printk message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump up driver version to match newer NIC firmware. Also update
nic_rx_stats (a struct common to host driver and firmware) by adding a new
field: fw_total_fwd_bytes.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For SGMII/RGMII/QSGMII interfaces when physical link goes down
while traffic is high is resulting in underflow condition being set
on that specific BGX's LMAC. Which assets a backpresure and VNIC stops
transmitting packets.
This is due to BGX being disabled in link status change callback while
packet is in transit. This patch fixes this issue by not disabling BGX
but instead just disables packet Rx and Tx.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes all checkpatch occurences of
"CHECK: spaces preferred around that '{+,-}' (ctx:VxV)"
in moxart_ether code.
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No space is necessary after a cast
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed coding style for null comparisons in moxart_ether driver
to be more consistent with the rest of the kernel coding style
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'unsigned int' instead of 'unsigned'
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary braces from single-line if statement
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZee4OAAoJEEg/ir3gV/o+/J0H/1Ko7FROlb5J1fRr32R309vH
fG7GikFdqiYMRshWzqBsNsbZRaxZmgifWv87d9w6vgW/BpsXuvGXAqqcMgOqChRI
bevTXaq9vwpgqkUuUuFkfRgsp496+ADAwF1aXH/LHN9EyVOqnteZgqugBurgyNcZ
wC6sl613KUPTuaV8O6jNEne/4BrIonz+OQCJU+IT2H6OuJzuGgLNSWvnM4ugOVeX
IQUuG9mV4qKh0srJwP4CsVk59vdJitdqqE0paxJrWLx5wTwY23vOshwBc6ZqAdRM
/KZtCIFyR+ez8d+ZkZ5L2UDdUSkFedawAxD7nreARmG/ZRa8RtrpnVyElcnHPS8=
=rIWI
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2017-07-27-V2' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-07-27
This series contains some misc fixes to the mlx5 driver.
Please pull and let me know if there's any problem.
V1->V2:
- removed redundant braces
for -stable:
4.7
net/mlx5: Fix command bad flow on command entry allocation failure
4.9
net/mlx5: Consider tx_enabled in all modes on remap
net/mlx5e: Fix outer_header_zero() check size
4.10
net/mlx5: Fix mlx5_add_flow_rules call with correct num of dests
4.11
net/mlx5: Fix mlx5_ifc_mtpps_reg_bits structure size
net/mlx5e: Add field select to MTPPS register
net/mlx5e: Fix broken disable 1PPS flow
net/mlx5e: Change 1PPS out scheme
net/mlx5e: Add missing support for PTP_CLK_REQ_PPS request
net/mlx5e: Fix wrong delay calculation for overflow check scheduling
net/mlx5e: Schedule overflow check work to mlx5e workqueue
4.12
net/mlx5: Fix command completion after timeout access invalid structure
net/mlx5e: IPoIB, Modify add/remove underlay QPN flows
I hope this is not too much, but most of the patches do apply cleanly on -stable.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 tunnels use sizeof(struct in6_addr) as dev->addr_len,
but in many places especially bonding, we use struct sockaddr
to copy and set mac addr, this could lead to stack out-of-bounds
access.
Fix it by using a larger address storage like bonding.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Saeed Mahameed