The current SH DMA API is somewhat broken, not correctly matching
virtual channel to the correct SH DMAC. This wasn't noticeable when
using g2 DMA for the sound driver - one channel 0 is as good as any
other! - but caused the pvr2 driver to fail.
This patch fixes the pvr2 problem and consequently fixes the sound
driver to ensure it continues to function.
Signed-off by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the r2d board support in a few ways:
- CPU_SUBTYPE_SH7751R is selected in the defconfig to play well
with the r2d board Kconfig entry. Without this the defconfig
results in no board enabled.
- Enable EARLY_PRINTK.
- Enable SH_STANDARD_BIOS
- this works well for early printk on the r2d board.
- Add "earlyprink=bios" to the cmdline for early serial port
output by default.
- CONFIG_SUBTYPE_SH7751R support is added to the sh-specific
pci makefile.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently this has a prompt to allow users to change it. There's
no reason to do this, and it has caused breakage and confusion
in the past, so remove it entirely.
We'll get rid of this when the whole driver is tidied for
the driver model.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was accidentally set as "GPLv2", whereas the kernel expects v2
to be written "GPL v2", this caused complaints regarding the use
of the platform device APIs when built as a module.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's no point in keeping these around, they've been broken
for some time, and the dmaenging/async_tx framework provides a
far more reasonable interface.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2 can presently get in to some pretty bogus states, so
we tidy up the dependencies a bit and get it all building
again.
This gets us a bit closer to a functional allyesconfig
and allmodconfig, though there are still a few things to
fix up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Trivial fix for arch/sh/drivers/dma/dma-api.c compile failure:
CC arch/sh/drivers/dma/dma-api.o
a/arch/sh/drivers/dma/dma-api.c: In function 'dma_wait_for_completion':
a/arch/sh/drivers/dma/dma-api.c:233: error: 'TASK_UNINTERRUPTIBLE' undeclared (first use in this function)
a/arch/sh/drivers/dma/dma-api.c:233: error: (Each undeclared identifier is reported only once
a/arch/sh/drivers/dma/dma-api.c:233: error: for each function it appears in.)
a/arch/sh/drivers/dma/dma-api.c:233: warning: implicit declaration of function 'schedule'
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The DMABRG is a special DMA unit within the SH7760 which does data
transfers from main memory to Audio units and USB shared memory.
It has 3 IRQ lines which generate 10 events, which have to be masked
unmasked and acked in a single 32bit register. It works independently
from the tradition SH DMAC, but blocks usage of DMAC channel 0.
This patch adds 2 functions to associate callbacks with DMABRG events
and initialization.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some fixups for the R7785RP board. Gets iVDR working.
Signed-off-by: Ryusuke Sakato <sakato.ryusuke@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for the SH7780 PCIC on the Solution Engine 7780,
missing from the previous board-support patch.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7780-based Solution Engine reference board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.zh@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the L-BOX RE2 router.
http://www.nttcom.co.jp/l-box/
L-BOX RE2 is a SH7751R-based router. It has CF, Cardbus, serial,
and LAN x2. This is one of the very few SH boards that a general
person can obtain now.
The L-BOX shipped with a 2.4.28 kernel, this is a rewritten patch
adding it to current git.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Updates for the landisk board:
- The push_switch framework was used.
- landisk_pwb.c was divided into psw.c and gio.c.
- pata_platform was supported in USL-5P.
- irq.c was rewritten.
- io.c was replaced with generic I/O routines.
Signed-off-by: kogiidena <kogiidena@eggplant.ddo.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements stricter and more compliant knightrider strobing in the
heartbeat handler. While there still seems to be some debate as to
whether the double 0 is "more" correct or not, this updated version
appears to have general consensus. Fixes a long-term "bug".
Signed-off-by: Takashi YOSHII <takashi.yoshii.ze@hitachi.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7785-based Highlander board.
Some of the Highlander support code is reordered so that most of it
can be reused directly.
This also plugs in missing SH7785 checks in the places that need it,
as this is the first board to support the CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When a SH7751R system includes a card that has wide range space
like a graphics card, the pci-pci bridge controller can't set the
correct address range.
For example, when *lower_limit is 0xfd000000 and bar_size is
0x4000000, in the following code at arch/sh/drivers/pci/pci-auto.c,
0x0 is set in bar_value.
pciauto_setup_bars()
{
...
bar_value = ((*lower_limit - 1) & ~(bar_size - 1)) + bar_size;
...
*lower_limit = bar_value + bar_size;
}
As a result, 0x4000000 is set in *lower_limit, but this value is wrong.
The following patch avoids this problem by checking the range of the
value and refusing to update the BAR if the calculated value ends up
being bogus.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Neither of these have had any maintenance in years, and there's
no interest in keeping them straggling along. These have already
been slated for removal some time, so finally just get rid of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the various board heartbeat LED implementations,
used for strobing the load average across a LED bank. Those boards
not implementing a full bank can hook in via the LED class.
We leave the compat hook in the machvec for now until those non-banked
boards are able to migrate to the drivers/leds.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch does the following:
- remove the make_ipr_irq stuff from dma-sh.c and replace it
with a simple channel<->irq mapping table.
- add DMTEx_IRQ constants for sh4 cpus
- fix sh7751 DMAE irq number
The SH7780 uses the same IRQs for DMA as other SH4 types, so
I put the constants on top of the dma.h file.
Other CPU types need to #define their own DMTEx_IRQ contants
in their appropriate header.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends the SH DMA API for allowing handling of DMA
channels based off of their respective capabilities.
A couple of functions are added to the existing API,
the core bits are register_chan_caps() for registering
channel capabilities, and request_dma_bycap() for fetching
a channel dynamically based off of a capability set.
Signed-off-by: Mark Glaisher <mark.glaisher@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass along the dev_id from request_dma() all the way down,
rather than inserting an artificial name relating to the TEI
line that we were doing before.
This makes the line a bit less obvious, but dev_id is the proper
behaviour for this regardless.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we linked in the ISA DMA wrapper unconditionally.
As there are very few users of this, it's better to make it
conditional.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle the case where no registered DMACs exist somewhat more
gracefully. While we're at it, check for sysdev_create_file()
failing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for a generic push switch framework. Adaptable for
various switches, including GPIO switches and the push switches commonly
found on Renesas debug boards.
This allows switch states to be trivially reported through sysfs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This drops the various IRQ headers that were floating around
and primarily providing hardcoded IRQ definitions for the
various CPU subtypes. This quickly got to be an unmaintainable
mess, made even more evident by the subtle breakage introduced
by the SH-2 and SH-2A changes.
Now that subtypes are able to register IRQ maps directly, just
rip all of the headers out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The conversion from IPR-IRQ to IRQ-chip resulted in the
ipr data being allocated in a local variable in
make_ipr_irq - breaking anything using IPR interrupts.
This changes all of the callers of make_ipr_irq to
allocate a static structure containing the IPR data which
is then passed to make_ipr_irq. This removes the need for
make_ipr_irq to allocate any additional space for the IPR
information.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now with the ide.h mess sorted out, most of these boards
don't need their own directory. Move the headers out, and
update the driver paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix a problem uncovered by the recent change to always check the
arguments to pr_debug. The sh7751 was using the wrong name for the
PCI IO base address.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This fixes a long-standing FIXME for G2 DMA, where we finally
wire up the IRQ handler and allow for sampling remaining bytes
while in-flight.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Inhibit mapping through page tables in __ioremap() for PCI memory
apertures on SH7751 and SH7780-style PCI controllers, translation is
not possible for these areas. For other users that map a small window
in P1/P2 space, ioremap() traps that already, and should never make
it to __ioremap().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This cleans up quite a lot of the PCI mess that we
currently have, and attempts to consolidate the
duplication in the SH7780 and SH7751 PCI controllers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ioremap() overhaul. Add support for transparent PMB mapping, get rid of
p3_ioremap(), etc. Also drop ioremap() and iounmap() routines from the
machvec, as everyone can use the generic ioremap() API instead. For PCI
memory apertures and other special cases, use the pci_iomap() API, as
boards are already required to get the mapping right there.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We had quite a bit of whitespace damage, clean most of it up..
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Arthur Othieno <a.othieno@bluewin.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Adrian McMenamin