Currently this driver does not support cropping. The supported modes
are the following, all capturing the entire area:
- 3840x2160, 1:1 binning (native sensor resolution)
- 1920x1080, 2:1 binning
- 1280x720, 3:1 binning
The VIDIOC_SUBDEV_S_FMT ioctl chooses among these 3 configurations the
one that matches the requested format.
Add cropping support via VIDIOC_SUBDEV_S_SELECTION: with target
V4L2_SEL_TGT_CROP to choose the captured area, with
V4L2_SEL_TGT_COMPOSE to choose the output resolution.
To maintain backward compatibility we also allow setting the compose
format via VIDIOC_SUBDEV_S_FMT. To obtain this, compose rect and
output format are computed in the common helper function
__imx274_change_compose(), which sets both to the same width/height
values.
Cropping also calls __imx274_change_compose() whenever cropping rect
size changes in order to reset the compose rect (and output format
size) for 1:1 binning.
Also rename enum imx274_mode to imx274_binning (and its values from
IMX274_MODE_BINNING_* to IMX274_BINNING_*). Without cropping, the two
naming are equivalent. With cropping, the resolution could be
different, e.g. using 2:1 binning mode to crop 1200x960 and output a
600x480 format. Using binning in the names avoids any
misunderstanding. For the same reason, replace the 'size' field in
struct imx274_frmfmt with 'bin_ratio'.
[Sakari Ailus: Remove leftover condition in imx274_apply_trimming]
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently 2-bytes and 3-bytes registers are set by very similar
functions doing the needed shift & mask manipulation, followed by very
similar for loops setting one byte at a time over I2C.
Replace all of this code by a unique helper function that calls
regmap_bulk_write(), which has two advantages:
- sets all the bytes in a unique I2C transaction
- removes lots of now unused code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_write_table() is a mere wrapper (and the only user) to
imx274_regmap_util_write_table_8(). Remove this useless indirection by
merging the two functions into one.
Also get rid of the wait_ms_addr and end_addr parameters since it does
not make any sense to give them any values other than
IMX274_TABLE_WAIT_MS and IMX274_TABLE_END.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
IMX274_DEFAULT_MODE is defined but not used. Start using it, so the
default can be more easily changed without digging into the code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
After restructuring struct imx274_frmfmt, the mode_index field is
still in use only for two dev_dbg() calls in imx274_s_stream(). Let's
remove it and avoid duplicated information.
Replacing the first usage requires some rather annoying but trivial
pointer math. The other one can be removed entirely since it would
print the same value anyway.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Data about the implemented readout modes is partially stored in
imx274_formats[], the rest is scattered in several arrays. The latter
are then accessed using the mode index, e.g.:
min_frame_len[priv->mode_index]
Consolidate all these data in imx274_formats[], and store a pointer to
the selected mode (i.e. imx274_formats[priv->mode_index]) in the main
device struct. This way code to use these data becomes more readable,
e.g.:
priv->mode->min_frame_len
This removes lots of scaffolding code and keeps data about each mode
in a unique place.
Also remove a parameter to imx274_mode_regs() that is now unused.
While this adds the mode pointer to the device struct, it does not
remove the mode_index from it because mode_index is still used in two
dev_dbg() calls. This will be handled in a follow-up commit.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The current probe function calls v4l2_ctrl_handler_setup() before
initializing the format info. This triggers call paths such as:
imx274_probe -> v4l2_ctrl_handler_setup -> imx274_s_ctrl ->
imx274_set_exposure, where priv->mode_index is accessed before being
assigned.
This is wrong but does not trigger a visible bug because priv is
zero-initialized and 0 is the default value for priv->mode_index. But
this would become a crash in follow-up commits when mode_index is
replaced by a pointer that must always be valid.
Fix the bug before it shows up by initializing struct members early.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
mode_table[] has 3 members that are accessed based on their index, which
makes worth using an array.
The other members are always accessed with a constant index. This added
indirection gives no improvement and only makes code more verbose.
Remove these pointers from the array and access them directly.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Most registers are defined using the name used in the datasheet.
E.g. the defines for the HMAX register are IMX274_HMAX_REG_*.
Rename the SHR and VMAX register accordingly. Also move them close to
related registers: SHR close to SVR, VMAX close to HMAX.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
struct imx274_frmfmt is instantiated only in the imx274_formats[]
array, where imx274_formats[N].mode always equals N (via enum
imx274_mode). So .mode carries no information, and unsurprisingly it
is never used.
mbus_code is never used because the 12 bit modes are not implemented.
The colorspace member is also never used, which is normal since the
imx274 sensor can output only one colorspace.
Let's get rid of all of them.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
imx274_s_frame_interval() already has a direct pointer to the v4l2
exposure control, so reuse it to simplify code.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Document the unit to avoid having to look through the code to compute it.
Also clarify that these are min and max values.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Smatch complains that "err" can be uninitialized if we have a zero size
write. The flow analysis is a little complicated so I'm not sure if
that's possible or not, but it's harmless to set this to zero and it
makes the code easier to read.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As smatch reported:
drivers/media/i2c/imx274.c:659 imx274_regmap_util_write_table_8() error: uninitialized symbol 'err'.
There is a bug at imx274_regmap_util_write_table_8() with causes
it to randomly return a random error if range_count is zero.
Worse than that, the logic there starts with range_count
equal to zero, and periodically resets it to zero again.
As it is a way more likely that err assumes a non-zero value,
I suspect that the chance of this code to run is very small,
so, it would be worth to review the entire function.
Anyway, clearly it shouldn't be returning error if range_count
is zero. So, let's fix it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Add the missing MAINTAINERS entry for imx274, fix error handling in driver
probe and unregister the correct control handler in driver remove.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The variable ret is being checked for failure however it is not being set
from the return status from the call to imx274_mode_regs. Currently ret is
alwayus zero and the check is redundant. Fix this by assigning it.
Detected by CoverityScan, CID#1460278 ("Logically dead code")
Fixes: 0985dd306f ("media: imx274: V4l2 driver for Sony imx274 CMOS sensor")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
The imx274 is a Sony CMOS image sensor that has 1/2.5 image size.
It supports up to 3840x2160 (4K) 60fps, 1080p 120fps. The interface
is 4-lane MIPI CSI-2 running at 1.44Gbps each.
This driver has been tested on Xilinx ZCU102 platform with a Leopard
LI-IMX274MIPI-FMC camera board.
Support for the following features:
-Resolutions: 3840x2160, 1920x1080, 1280x720
-Frame rate: 3840x2160 : 5 – 60fps
1920x1080 : 5 – 120fps
1280x720 : 5 – 120fps
-Exposure time: 16 – (frame interval) micro-seconds
-Gain: 1x - 180x
-VFLIP: enable/disabledrivers/media/i2c/imx274.c
-Test pattern: 12 test patterns
Signed-off-by: Leon Luo <leonl@leopardimaging.com>
Tested-by: Sören Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Luca Ceresoli