On platforms where the Low Power S0 Idle _DSM interface is used,
on wakeup from suspend-to-idle, when it is known that the ACPI SCI
has triggered while suspended, dispatch the EC GPE in order to catch
all EC events that may have triggered the wakeup before carrying out
the noirq phase of device resume.
That is needed to handle power button wakeup on some platforms where
the EC goes into a low-power mode during suspend-to-idle and while in
that mode it will discard events after a timeout. If that timeout is
shorter than the time it takes to complete the noirq resume of
devices, looking for EC events after the latter is too late.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reported-by: Zhang Rui <rui.zhang@intel.com>
Tested-by: Wendy Wang <wendy.wang@intel.com>
acpi_ec.gpe is "unsigned long", hence treating it as "u32" would expose
the wrong half on big-endian 64-bit systems. Fix this by changing its
type to "u32" and removing the cast, as all other code already uses u32
or sometimes even only u8.
Fixes: 1195a09816 (ACPI: Provide /sys/kernel/debug/ec/...)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms (ASUS X550ZE and possibly all ASUS X series) with valid ECDT
EC but invalid DSDT EC, EC PM ops won't be invoked as ECDT EC is not an
ACPI device. Thus the following commit actually removed post-resume
acpi_ec_enable_event() invocation for such platforms, and triggered a
regression on them that after being resumed, EC (actually should be ECDT)
driver stops handling EC events:
Commit: c2b46d679b
Subject: ACPI / EC: Add PM operations to improve event handling for resume process
Notice that the root cause actually is "ECDT is not an ACPI device" rather
than "the timing of acpi_ec_enable_event() invocation", this patch fixes
this issue by enumerating ECDT EC as an ACPI device. Due to the existence
of the noirq stage, the ability of tuning the timing of
acpi_ec_enable_event() invocation is still meaningful.
This patch is a little bit different from the posted fix by moving
acpi_config_boot_ec() from acpi_ec_ecdt_start() to acpi_ec_add() to make
sure that EC event handling won't be stopped as long as the ACPI EC driver
is bound. Thus the following sequence shouldn't disable EC event handling:
unbind,suspend,resume,bind.
Fixes: c2b46d679b (ACPI / EC: Add PM operations to improve event handling for resume process)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=196847
Reported-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Cc: 4.9+ <stable@vger.kernel.org> # 4.9+
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add functionality to read LPIT table, which provides:
- Sysfs interface to read residency counters via
/sys/devices/system/cpu/cpuidle/low_power_idle_cpu_residency_us
/sys/devices/system/cpu/cpuidle/low_power_idle_system_residency_us
Here the count "low_power_idle_cpu_residency_us" shows the time spent
by CPU package in low power state. This is read via MSR interface,
which points to MSR for PKG C10.
Here the count "low_power_idle_system_residency_us" show the count the
system was in low power state. This is read via MMIO interface. This
is mapped to SLP_S0 residency on modern Intel systems. This residency
is achieved only when CPU is in PKG C10 and all functional blocks are
in low power state.
It is possible that none of the above counters present or anyone of the
counter present or all counters present.
For example: On my Kabylake system both of the above counters present.
After suspend to idle these counts updated and prints:
6916179
6998564
This counter can be read by tools like turbostat to display. Or it can
be used to debug, if modern systems are reaching desired low power state.
- Provides an interface to read residency counter memory address
This address can be used to get the base address of PMC memory
mapped IO. This is utilized by intel_pmc_core driver to print
more debug information.
In addition, to avoid code duplication to read iomem, removed the read of
iomem from acpi_os_read_memory() in osl.c and made a common function
acpi_os_read_iomem(). This new function is used for reading iomem in
in both osl.c and acpi_lpit.c.
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 2a5708409e (ACPI / EC: Fix a gap that ECDT EC cannot handle
EC events) introduced acpi_ec_ecdt_start(), but that function is
invoked before acpi_ec_query_init(), which is too early. This causes
the kernel to crash if an EC event occurs after boot, when ec_query_wq
is not valid:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000102
...
Workqueue: events acpi_ec_event_handler
task: ffff9f539790dac0 task.stack: ffffb437c0e10000
RIP: 0010:__queue_work+0x32/0x430
Normally, the DSDT EC should always be valid, so acpi_ec_ecdt_start()
is actually a no-op in the majority of cases. However, commit
c712bb58d8 (ACPI / EC: Add support to skip boot stage DSDT probe)
caused the probing of the DSDT EC as the "boot EC" to be skipped when
the ECDT EC is valid and uncovered the bug.
Fix this issue by invoking acpi_ec_ecdt_start() after acpi_ec_query_init()
in acpi_ec_init().
Link: https://jira01.devtools.intel.com/browse/LCK-4348
Fixes: 2a5708409e (ACPI / EC: Fix a gap that ECDT EC cannot handle EC events)
Fixes: c712bb58d8 (ACPI / EC: Add support to skip boot stage DSDT probe)
Reported-by: Wang Wendy <wendy.wang@intel.com>
Tested-by: Feng Chenzhou <chenzhoux.feng@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
While the rest of the world has standardized on _DSD as the way to store
device properties in AML (introduced with ACPI 5.1 in 2014), Apple has
been using a custom _DSM to achieve the same for much longer (ever since
they switched from DeviceTree-based PowerPC to Intel in 2005, verified
with MacOS X 10.4.11).
The theory of operation on macOS is as follows: AppleACPIPlatform.kext
invokes mergeEFIproperties() and mergeDSMproperties() for each device to
merge properties conveyed by EFI drivers as well as properties stored in
AML into the I/O Kit registry from which they can be retrieved by
drivers. We've been supporting EFI properties since commit 58c5475aba
("x86/efi: Retrieve and assign Apple device properties"). The present
commit adds support for _DSM properties, thereby completing our support
for Apple device properties. The _DSM properties are made available
under the primary fwnode, the EFI properties under the secondary fwnode.
So for devices which possess both property types, they can all be
elegantly accessed with the uniform API in <linux/property.h>.
Until recently we had no need to support _DSM properties, they contained
only uninteresting garbage. The situation has changed with MacBooks and
MacBook Pros introduced since 2015: Their keyboard is attached with SPI
instead of USB and the _CRS data which is necessary to initialize the
spi driver only contains valid information if OSPM responds "false" to
_OSI("Darwin"). If OSPM responds "true", _CRS is empty and the spi
driver fails to initialize. The rationale is very simple, Apple only
cares about macOS and Windows: On Windows, _CRS contains valid data,
whereas on macOS it is empty. Instead, macOS gleans the necessary data
from the _DSM properties.
Since Linux deliberately defaults to responding "true" to _OSI("Darwin"),
we need to emulate macOS' behaviour by initializing the spi driver with
data returned by the _DSM.
An out-of-tree driver for the SPI keyboard exists which currently binds
to the ACPI device, invokes the _DSM, parses the returned package and
instantiates an SPI device with the data gleaned from the _DSM:
https://github.com/cb22/macbook12-spi-driver/commit/9a416d699ef4https://github.com/cb22/macbook12-spi-driver/commit/0c34936ed9a1
By adding support for Apple's _DSM properties in generic ACPI code, the
out-of-tree driver will be able to register as a regular SPI driver,
significantly reducing its amount of code and improving its chances to
be mainlined.
The SPI keyboard will not be the only user of this commit: E.g. on the
MacBook8,1, the UART-attached Bluetooth device likewise returns empty
_CRS data if OSPM returns "true" to _OSI("Darwin").
The _DSM returns a Package whose format unfortunately deviates slightly
from the _DSD spec: The properties are marshalled up in a single Package
as alternating key/value elements, unlike _DSD which stores them as a
Package of 2-element Packages. The present commit therefore converts
the Package to _DSD format and the ACPI core can then treat the data as
if Apple would follow the standard.
Well, except for one small annoyance: The properties returned by the
_DSM only ever have one of two types, Integer or Buffer. The former is
retrievable as usual with device_property_read_u64(), but the latter is
not part of the _DSD spec and it is not possible to retrieve Buffer
properties with the device_property_read_*() functions due to the type
checking performed in drivers/acpi/property.c. It is however possible
to retrieve them with acpi_dev_get_property(). Apple is using the
Buffer type somewhat sloppily to store null-terminated strings but also
integers. The real data type is not distinguishable by the ACPI core
and the onus is on the caller to use the contents of the Buffer in an
appropriate way.
In case Apple moves to _DSD in the future, this commit first checks for
_DSD and falls back to _DSM only if _DSD is not found.
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from
suspend-to-idle) introduced acpi_freeze_sync() whose purpose is to
flush all of the processing of possible wakeup events signaled via
the ACPI SCI. However, it doesn't flush the query workqueue used
by the EC driver, so the events generated by the EC may not be
processed timely which leads to issues (increased overhead at least,
lost events possibly).
To fix that introduce acpi_ec_flush_work() that will flush all of
the outstanding EC work and call it from acpi_freeze_sync().
Fixes: eed4d47efe (ACPI / sleep: Ignore spurious SCI wakeups from suspend-to-idle)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework
(ACPI, DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=EcrF
-----END PGP SIGNATURE-----
Merge tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties framework updates from Rafael Wysocki:
"These mostly rearrange the device properties core code and add a few
helper functions to it as a foundation for future work.
Specifics:
- Rearrange the core device properties code by moving the code
specific to each supported platform configuration framework (ACPI,
DT and build-in) into a separate file (Sakari Ailus).
- Add helper functions for accessing device properties in a
firmware-agnostic way (Sakari Ailus, Kieran Bingham)"
* tag 'devprop-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: Add fwnode_graph_get_port_parent
device property: Add FW type agnostic fwnode_graph_get_remote_node
device property: Introduce fwnode_device_is_available()
device property: Move fwnode graph ops to firmware specific locations
device property: Move FW type specific functionality to FW specific files
ACPI: Constify argument to acpi_device_is_present()
Some recent Dell laptops, including the XPS13 model numbers 9360 and
9365, cannot be woken up from suspend-to-idle by pressing the power
button which is unexpected and makes that feature less usable on
those systems. Moreover, on the 9365 ACPI S3 (suspend-to-RAM) is
not expected to be used at all (the OS these systems ship with never
exercises the ACPI S3 path in the firmware) and suspend-to-idle is
the only viable system suspend mechanism there.
The reason why the power button wakeup from suspend-to-idle doesn't
work on those systems is because their power button events are
signaled by the EC (Embedded Controller), whose GPE (General Purpose
Event) line is disabled during suspend-to-idle transitions in Linux.
That is done on purpose, because in general the EC tends to be noisy
for various reasons (battery and thermal updates and similar, for
example) and all events signaled by it would kick the CPUs out of
deep idle states while in suspend-to-idle, which effectively might
defeat its purpose.
Of course, on the Dell systems in question the EC GPE must be enabled
during suspend-to-idle transitions for the button press events to
be signaled while suspended at all, but fortunately there is a way
out of this puzzle.
First of all, those systems have the ACPI_FADT_LOW_POWER_S0 flag set
in their ACPI tables, which means that the OS is expected to prefer
the "low power S0 idle" system state over ACPI S3 on them. That
causes the most recent versions of other OSes to simply ignore ACPI
S3 on those systems, so it is reasonable to expect that it should not
be necessary to block GPEs during suspend-to-idle on them.
Second, in addition to that, the systems in question provide a special
firmware interface that can be used to indicate to the platform that
the OS is transitioning into a system-wide low-power state in which
certain types of activity are not desirable or that it is leaving
such a state and that (in principle) should allow the platform to
adjust its operation mode accordingly.
That interface is a special _DSM object under a System Power
Management Controller device (PNP0D80). The expected way to use it
is to invoke function 0 from it on system initialization, functions
3 and 5 during suspend transitions and functions 4 and 6 during
resume transitions (to reverse the actions carried out by the
former). In particular, function 5 from the "Low-Power S0" device
_DSM is expected to cause the platform to put itself into a low-power
operation mode which should include making the EC less verbose (so to
speak). Next, on resume, function 6 switches the platform back to
the "working-state" operation mode.
In accordance with the above, modify the ACPI suspend-to-idle code
to look for the "Low-Power S0" _DSM interface on platforms with the
ACPI_FADT_LOW_POWER_S0 flag set in the ACPI tables. If it's there,
use it during suspend-to-idle transitions as prescribed and avoid
changing the GPE configuration in that case. [That should reflect
what the most recent versions of other OSes do.]
Also modify the ACPI EC driver to make it handle events during
suspend-to-idle in the usual way if the "Low-Power S0" _DSM interface
is going to be used to make the power button events work while
suspended on the Dell machines mentioned above
Link: http://www.uefi.org/sites/default/files/resources/Intel_ACPI_Low_Power_S0_Idle.pdf
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This will be needed in constifying the fwnode API.
The side effects the function had have been moved to the callers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The ACPI SCI (System Control Interrupt) is set up as a wakeup IRQ
during suspend-to-idle transitions and, consequently, any events
signaled through it wake up the system from that state. However,
on some systems some of the events signaled via the ACPI SCI while
suspended to idle should not cause the system to wake up. In fact,
quite often they should just be discarded.
Arguably, systems should not resume entirely on such events, but in
order to decide which events really should cause the system to resume
and which are spurious, it is necessary to resume up to the point
when ACPI SCIs are actually handled and processed, which is after
executing dpm_resume_noirq() in the system resume path.
For this reasons, add a loop around freeze_enter() in which the
platforms can process events signaled via multiplexed IRQ lines
like the ACPI SCI and add suspend-to-idle hooks that can be
used for this purpose to struct platform_freeze_ops.
In the ACPI case, the ->wake hook is used for checking if the SCI
has triggered while suspended and deferring the interrupt-induced
system wakeup until the events signaled through it are actually
processed sufficiently to decide whether or not the system should
resume. In turn, the ->sync hook allows all of the relevant event
queues to be flushed so as to prevent events from being missed due
to race conditions.
In addition to that, some ACPI code processing wakeup events needs
to be modified to use the "hard" version of wakeup triggers, so that
it will cause a system resume to happen on device-induced wakeup
events even if the "soft" mechanism to prevent the system from
suspending is not enabled. However, to preserve the existing
behavior with respect to suspend-to-RAM, this only is done in
the suspend-to-idle case and only if an SCI has occurred while
suspended.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
/sys/firmware/acpi/hotplug/force_remove was presumably added to support
auto offlining in the past. This is, however, inherently dangerous for
some hotplugable resources like memory. The memory offlining fails when
the memory is still in use and cannot be dropped or migrated. If we
ignore the failure we are basically allowing for subtle memory
corruption or a crash.
We have actually noticed the later while hitting BUG() during the memory
hotremove (remove_memory):
ret = walk_memory_range(PFN_DOWN(start), PFN_UP(start + size - 1), NULL,
check_memblock_offlined_cb);
if (ret)
BUG();
it took us quite non-trivial time realize that the customer had
force_remove enabled. Even if the BUG was removed here and we could
propagate the error up the call chain it wouldn't help at all because
then we would hit a crash or a memory corruption later and harder to
debug. So force_remove is unfixable for the memory hotremove. We haven't
checked other hotplugable resources to be prone to a similar problems.
Remove the force_remove functionality because it is not fixable currently.
Keep the sysfs file and report an error if somebody tries to enable it.
Encourage users to report about the missing functionality and work with
them with an alternative solution.
Reviewed-by: Lee, Chun-Yi <jlee@suse.com>
Signed-off-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The hot removal of IOAPIC is handling PCI and ACPI removal in one go. That
only works when the PCI drivers released the interrupt resources, but
breaks when a IOAPIC interrupt is still associated to a PCI device.
The new pcibios_release_device() callback allows to solve that problem by
splitting the removal into two steps:
1) PCI removal:
Release all PCI resources including eventually not yet released IOAPIC
interrupts via the new pcibios_release_device() callback.
2) ACPI removal:
After release of all PCI resources the ACPI resources can be released
without issue.
[ tglx: Rewrote changelog ]
Signed-off-by: Rui Wang <rui.y.wang@intel.com>
Cc: tony.luck@intel.com
Cc: linux-pci@vger.kernel.org
Cc: rjw@rjwysocki.net
Cc: linux-acpi@vger.kernel.org
Cc: fengguang.wu@intel.com
Cc: helgaas@kernel.org
Cc: kbuild-all@01.org
Cc: bhelgaas@google.com
Link: http://lkml.kernel.org/r/1488288869-31290-3-git-send-email-rui.y.wang@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When GPE is not enabled, it is not efficient to use the wait polling mode
as it introduces an unexpected scheduler delay.
So before the GPE handler is installed, this patch uses busy polling mode
for all EC(s) and the logic can be applied to non boot EC(s) during the
suspend/resume process.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=191561
Tested-by: Jakobus Schurz <jakobus.schurz@gmail.com>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes, the users may require a quirk to be provided from ACPI subsystem
core to prevent a GPE from flooding.
Normally, if a GPE cannot be dispatched, ACPICA core automatically prevents
the GPE from firing. But there are cases the GPE is dispatched by _Lxx/_Exx
provided via AML table, and OSPM is lacking of the knowledge to get
_Lxx/_Exx correctly executed to handle the GPE, thus the GPE flooding may
still occur.
The existing quirk mechanism can be enabled/disabled using the following
commands to prevent such kind of GPE flooding during runtime:
# echo mask > /sys/firmware/acpi/interrupts/gpe00
# echo unmask > /sys/firmware/acpi/interrupts/gpe00
To avoid GPE flooding during boot, we need a boot stage mechanism.
This patch provides such a boot stage quirk mechanism to stop this kind of
GPE flooding. This patch doesn't fix any feature gap but since the new
feature gaps could be found in the future endlessly, and can disappear if
the feature gaps are filled, providing a boot parameter rather than a DMI
table should suffice.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=53071
Link: https://bugzilla.kernel.org/show_bug.cgi?id=117481
Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/887793
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 apic updates from Ingo Molnar:
"The main changes are:
- Persistent CPU/node numbering across CPU hotplug/unplug events.
This is a pretty involved series of changes that first fetches all
the information during bootup and then uses it for the various
hotplug/unplug methods. (Gu Zheng, Dou Liyang)
- IO-APIC hot-add/remove fixes and enhancements. (Rui Wang)
- ... various fixes, cleanups and enhancements"
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (22 commits)
x86/apic: Fix silent & fatal merge conflict in __generic_processor_info()
acpi: Fix broken error check in map_processor()
acpi: Validate processor id when mapping the processor
acpi: Provide mechanism to validate processors in the ACPI tables
x86/acpi: Set persistent cpuid <-> nodeid mapping when booting
x86/acpi: Enable MADT APIs to return disabled apicids
x86/acpi: Introduce persistent storage for cpuid <-> apicid mapping
x86/acpi: Enable acpi to register all possible cpus at boot time
x86/numa: Online memory-less nodes at boot time
x86/apic: Get rid of apic_version[] array
x86/apic: Order irq_enter/exit() calls correctly vs. ack_APIC_irq()
x86/ioapic: Ignore root bridges without a companion ACPI device
x86/apic: Update comment about disabling processor focus
x86/smpboot: Check APIC ID before setting up default routing
x86/ioapic: Fix IOAPIC failing to request resource
x86/ioapic: Fix lost IOAPIC resource after hot-removal and hotadd
x86/ioapic: Fix setup_res() failing to get resource
x86/ioapic: Support hot-removal of IOAPICs present during boot
x86/ioapic: Change prototype of acpi_ioapic_add()
x86/apic, ACPI: Fix incorrect assignment when handling apic/x2apic entries
...
* acpi-wdat:
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / watchdog: Add support for WDAT hardware watchdog
* acpi-ec:
ACPI / EC: Fix issues related to boot_ec
ACPI / EC: Fix a gap that ECDT EC cannot handle EC events
ACPI / EC: Fix a memory leakage issue in acpi_ec_add()
ACPI / EC: Cleanup first_ec/boot_ec code
ACPI / EC: Enable event freeze mode to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for suspend process
ACPI / EC: Add PM operations to improve event handling for resume process
ACPI / EC: Fix an issue that SCI_EVT cannot be detected after event is enabled
ACPI / EC: Add EC_FLAGS_QUERY_ENABLED to reveal a hidden logic
ACPI / EC: Add PM operations for suspend/resume noirq stage
Starting from Intel Skylake the iTCO watchdog timer registers were moved to
reside in the same register space with SMBus host controller. Not all
needed registers are available though and we need to unhide P2SB (Primary
to Sideband) device briefly to be able to read status of required NO_REBOOT
bit. The i2c-i801.c SMBus driver used to handle this and creation of the
iTCO watchdog platform device.
Windows, on the other hand, does not use the iTCO watchdog hardware
directly even if it is available. Instead it relies on ACPI Watchdog Action
Table (WDAT) table to describe the watchdog hardware to the OS. This table
contains necessary information about the the hardware and also set of
actions which are executed by a driver as needed.
This patch implements a new watchdog driver that takes advantage of the
ACPI WDAT table. We split the functionality into two parts: first part
enumerates the WDAT table and if found, populates resources and creates
platform device for the actual driver. The second part is the driver
itself.
The reason for the split is that this way we can make the driver itself to
be a module and loaded automatically if the WDAT table is found. Otherwise
the module is not loaded.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible to register _Qxx from namespace and use the ECDT EC to
perform event handling. The reported bug reveals that Windows is using ECDT
in this way in case the namespace EC is not present. This patch facilitates
Linux to support ECDT in this way.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=115021
Reported-and-tested-by: Luya Tshimbalanga <luya@fedoraproject.org>
Tested-by: Jonh Henderson <jw.hendy@gmail.com>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch makes 2 changes:
1. Restore old behavior
Originally, EC driver stops handling both events and transactions in
acpi_ec_block_transactions(), and restarts to handle transactions in
acpi_ec_unblock_transactions_early(), restarts to handle both events and
transactions in acpi_ec_unblock_transactions().
While currently, EC driver still stops handling both events and
transactions in acpi_ec_block_transactions(), but restarts to handle both
events and transactions in acpi_ec_unblock_transactions_early().
This patch tries to restore the old behavior by dropping
__acpi_ec_enable_event() from acpi_unblock_transactions_early().
2. Improve old behavior
However this still cannot fix the real issue as both of the
acpi_ec_unblock_xxx() functions are invoked in the noirq stage. Since the
EC driver actually doesn't implement the event handling in the polling
mode, re-enabling the event handling too early in the noirq stage could
result in the problem that if there is no triggering source causing
advance_transaction() to be invoked, pending SCI_EVT cannot be detected by
the EC driver and _Qxx cannot be triggered.
It actually makes sense to restart the event handling in any point during
resuming after the noirq stage. Just like the boot stage where the event
handling is enabled in .add(), this patch further moves
acpi_ec_enable_event() to .resume(). After doing that, the following 2
functions can be combined:
acpi_ec_unblock_transactions_early()/acpi_ec_unblock_transactions().
The differences of the event handling availability between the old behavior
(this patch isn't applied) and the new behavior (this patch is applied) are
as follows:
!Applied Applied
before suspend Y Y
suspend before EC Y Y
suspend after EC Y Y
suspend_late Y Y
suspend_noirq Y (actually N) Y (actually N)
resume_noirq Y (actually N) Y (actually N)
resume_late Y (actually N) Y (actually N)
resume before EC Y (actually N) Y (actually N)
resume after EC Y (actually N) Y
after resume Y (actually N) Y
Where "actually N" means if there is no triggering source, the EC driver
is actually not able to notice the pending SCI_EVT occurred in the noirq
stage. So we can clearly see that this patch has improved the situation.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Following the fwnode of a device is currently a one-way road: We provide
ACPI_COMPANION() to obtain the fwnode but there's no (public) method to
do the reverse. Granted, there may be multiple physical_nodes, but often
the first one in the list is sufficient.
A handy function to obtain it was introduced with commit 3b95bd1605
("ACPI: introduce a function to find the first physical device"), but
currently it's only available internally.
We're about to add an EFI Device Path parser which needs this function.
Consider the following device path: ACPI(PNP0A03,0)/PCI(28,2)/PCI(0,0)
The PCI root is encoded as an ACPI device in the path, so the parser
has to find the corresponding ACPI device, then find its physical node,
find the PCI bridge in slot 1c (decimal 28), function 2 below it and
finally find the PCI device in slot 0, function 0.
To this end, make acpi_get_first_physical_node() public.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is reported that on some platforms, resume speed is not fast. The cause
is: in noirq stage, EC driver is working in polling mode, and each state
machine advancement requires a context switch.
The context switch is not necessary to the EC driver's polling mode. This
patch implements PM hooks to automatically switch the driver to/from the
busy polling mode to eliminate the overhead caused by the context switch.
This finally contributes to the tuning result: acpi_pm_finish() execution
time is improved from 192ms to 6ms.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Reported-and-tested-by: Todd E Brandt <todd.e.brandt@linux.intel.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for ACPI reconfiguration notifiers to allow subsystems
to react to changes in the ACPI tables that happen after the initial
enumeration. This is similar with the way dynamic device tree
notifications work.
The reconfigure notifications supported for now are device add and
device remove.
Since ACPICA allows only one table notification handler, this patch
makes the table notifier function generic and moves it out of the
sysfs specific code.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
According to the Windows probing result, during the table loading, the EC
device described in the ECDT should be used. And the ECDT EC is also
effective during the period the namespace objects are initialized (we can
see a separate process executing _STA/_INI on Windows before executing
other device specific control methods, for example, EC._REG). During the
device enumration, the EC device described in the DSDT should be used. But
there are differences between Linux and Windows around the device probing
order. Thus in Linux, we should enable the DSDT EC as early as possible
before enumerating devices in order not to trigger issues related to the
device enumeration order differences.
This patch thus converts acpi_boot_ec_enable() into acpi_ec_dsdt_probe() to
fix the gap. This also fixes a user reported regression triggered after we
switched the "table loading"/"ECDT support" to be ACPI spec 2.0 compliant.
Fixes: 59f0aa9480 (ACPI 2.0 / ECDT: Remove early namespace reference from EC)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=119261
Reported-and-tested-by: Gabriele Mazzotta <gabriele.mzt@gmail.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
_OSI handling code grows giant and it's time to move them into one file.
This patch collects all _OSI handling code into one single file.
So that we only have the following functions to be used externally:
early_acpi_osi_init(): Used by DMI detections;
acpi_osi_init(): Used to initialize OSI command line settings and install
Linux specific _OSI handler;
acpi_osi_setup(): The API that should be used by the external quirks.
acpi_osi_is_win8(): The API is used by the external drivers to determine
if BIOS supports Win8.
CONFIG_DMI is not useful as stub dmi_check_system() can make everything
stub because of strip.
No functional changes.
Tested-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch moves acpi_os_table_override() and
acpi_os_physical_table_override() to tables.c.
Along with the mechanisms, acpi_initrd_initialize_tables() is also moved to
tables.c to form a static function. The following functions are renamed
according to this change:
1. acpi_initrd_override() -> renamed to early_acpi_table_init(), which
invokes acpi_table_initrd_init()
2. acpi_os_physical_table_override() -> which invokes
acpi_table_initrd_override()
3. acpi_initialize_initrd_tables() -> renamed to acpi_table_initrd_scan()
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There are several reports of freeze on enabling HWP (Hardware PStates)
feature on Skylake-based systems by the Intel P-states driver. The root
cause is identified as the HWP interrupts causing BIOS code to freeze.
HWP interrupts use the thermal LVT which can be handled by Linux
natively, but on the affected Skylake-based systems SMM will respond
to it by default. This is a problem for several reasons:
- On the affected systems the SMM thermal LVT handler is broken (it
will crash when invoked) and a BIOS update is necessary to fix it.
- With thermal interrupt handled in SMM we lose all of the reporting
features of the arch/x86/kernel/cpu/mcheck/therm_throt driver.
- Some thermal drivers like x86-package-temp depend on the thermal
threshold interrupts signaled via the thermal LVT.
- The HWP interrupts are useful for debugging and tuning
performance (if the kernel can handle them).
The native handling of thermal interrupts needs to be enabled
because of that.
This requires some way to tell SMM that the OS can handle thermal
interrupts. That can be done by using _OSC/_PDC in processor
scope very early during ACPI initialization.
The meaning of _OSC/_PDC bit 12 in processor scope is whether or
not the OS supports native handling of interrupts for Collaborative
Processor Performance Control (CPPC) notifications. Since on
HWP-capable systems CPPC is a firmware interface to HWP, setting
this bit effectively tells the firmware that the OS will handle
thermal interrupts natively going forward.
For details on _OSC/_PDC refer to:
http://www.intel.com/content/www/us/en/standards/processor-vendor-specific-acpi-specification.html
To implement the _OSC/_PDC handshake as described, introduce a new
function, acpi_early_processor_osc(), that walks the ACPI
namespace looking for ACPI processor objects and invokes _OSC for
them with bit 12 in the capabilities buffer set and terminates the
namespace walk on the first success.
Also modify intel_thermal_interrupt() to clear HWP status bits in
the HWP_STATUS MSR to acknowledge HWP interrupts (which prevents
them from firing continuously).
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
[ rjw: Subject & changelog, function rename ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-scan:
ACPI / scan: AMBA bus probing support
ACPI: introduce a function to find the first physical device
* acpi-osl:
ACPI / OSL: Add support to install tables via initrd
ACPI / OSL: Clean up initrd table override code
* acpi-apei:
ACPI / APEI: ERST: Fixed leaked resources in erst_init
ACPI / APEI: Fix leaked resources
This patch adds support to install tables from initrd.
If a table in the initrd wasn't used by the override mechanism,
the table would be installed after initializing all RSDT/XSDT
tables.
Link: https://lkml.org/lkml/2014/2/28/368
Reported-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On ARM64 some devices use the AMBA device and not the platform bus for
probing so add support for this. Uses a dummy clock for apb_pclk as ACPI
does not have a suitable clock representation and to keep the core
AMBA bus code unchanged between probing methods.
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Graeme Gregory <graeme.gregory@linaro.org>
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Factor out the code that finds the first physical device
of a given ACPI device. It is used in several places.
Signed-off-by: Aleksey Makarov <aleksey.makarov@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a missing space in the definition of struct acpi_device_bus_id.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
[ rjw: Subject and changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There's an idiom in use by 7 Linux drivers to detect the presence of a
particular ACPI HID by walking the namespace with acpi_get_devices().
The callback passed to acpi_get_devices() is mostly identical across
the drivers, leading to lots of duplicate code.
Add acpi_dev_present(), the ACPI equivalent to pci_dev_present(),
allowing us to deduplicate all that boilerplate in the drivers.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch of
debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlY6ePQACgkQMUfUDdst+ymNTgCgpP0CZw57GpwF/Hp2L/lMkVeo
Kx8AoKhEi4iqD5fdCQS9qTfomB+2/M6g
=g7ZO
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core updates for 4.4-rc1. Primarily a bunch
of debugfs updates, with a smattering of minor driver core fixes and
updates as well.
All have been in linux-next for a long time"
* tag 'driver-core-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: Add debugfs_create_ulong()
of: to support binding numa node to specified device in devicetree
debugfs: Add read-only/write-only bool file ops
debugfs: Add read-only/write-only size_t file ops
debugfs: Add read-only/write-only x64 file ops
debugfs: Consolidate file mode checks in debugfs_create_*()
Revert "mm: Check if section present during memory block (un)registering"
driver-core: platform: Provide helpers for multi-driver modules
mm: Check if section present during memory block (un)registering
devres: fix a for loop bounds check
CMA: fix CONFIG_CMA_SIZE_MBYTES overflow in 64bit
base/platform: assert that dev_pm_domain callbacks are called unconditionally
sysfs: correctly handle short reads on PREALLOC attrs.
base: soc: siplify ida usage
kobject: move EXPORT_SYMBOL() macros next to corresponding definitions
kobject: explain what kobject's sd field is
debugfs: document that debugfs_remove*() accepts NULL and error values
debugfs: Pass bool pointer to debugfs_create_bool()
ACPI / EC: Fix broken 64bit big-endian users of 'global_lock'
Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.
It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.
That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
global_lock is defined as an unsigned long and accessing only its lower
32 bits from sysfs is incorrect, as we need to consider other 32 bits
for big endian 64-bit systems. There are no such platforms yet, but the
code needs to be robust for such a case.
Fix that by changing type of 'global_lock' to u32.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the type of the return value of the acpi_sleep_proc_init()
method to be void, as this method never fails and its return value is never
used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>\
[ rjw : Fixed up the static inline stub ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch changes the type of the return value of the init_acpi_device_notify()
method to be void, as this method never fails and its return value is never
used.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* acpi-pm:
ACPI / bus: Move duplicate code to a separate new function
mfd: Add support for Intel Sunrisepoint LPSS devices
dmaengine: add a driver for Intel integrated DMA 64-bit
mfd: make mfd_remove_devices() iterate in reverse order
driver core: implement device_for_each_child_reverse()
klist: implement klist_prev()
Driver core: wakeup the parent device before trying probe
ACPI / PM: Attach ACPI power domain only once
PM / QoS: Make it possible to expose device latency tolerance to userspace
ACPI / PM: Update the copyright notice and description of power.c
acpi_debugfs_init function is declared with return type int in
drivers/acpi/internal.h when CONFIG_DEBUG_FS is enabled, but its
definition in drivers/acpi/debugfs.c has return type void. This is due
to commit aecad432fd ("ACPI: Cleanup custom_method debug stuff"),
which changed the return type from int to void without updating the
declaration.
Fix this inconsistency by updating acpi_debugfs_init prototype. While
at it, include internal.h in debugfs.c so that the compiler can check
that the declaration and definition remain compatible.
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Conflicts:
drivers/acpi/scan.c
The conflict is resolved by moving the just introduced
acpi_device_is_first_physical_node() to bus.c and using
the existing acpi_companion_match() from there.
There will be an additional commit to combine the two.
Some devices, like MFD subdevices, share a single ACPI companion device so
that they are able to access their resources and children. However,
currently all these subdevices are attached to the ACPI power domain and
this might cause that the power methods for the companion device get called
more than once.
In order to solve this we attach the ACPI power domain only to the first
physical device that is bound to the ACPI companion device. In case of MFD
devices, this is the parent MFD device itself.
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To reduce the size of scan.c and improve the readability of it, move
all code related to device sysfs, modalias creation etc. to a new
file called device_sysfs.c.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Rafael J. Wysocki