The only user of unique_tuple() get_unique_tuple() doesn't care about the
return value of unique_tuple(), so make unique_tuple() return void (nothing).
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
some users of nf_ct_ext_exist() know ct->ext isn't NULL. For these users, the
check for ct->ext isn't necessary, the function __nf_ct_ext_exist() can be
used instead.
the type of the return value of nf_ct_ext_exist() is changed to bool.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch moves NFULNL_COPY_PACKET definition from
linux/netfilter/nfnetlink_log.h to net/netfilter/nfnetlink_log.h
since this copy mode is only for internal use.
I have also changed the value from 0x03 to 0xff. Thus, we avoid
a gap from user-space that may confuse users if we add new
copy modes in the future.
This change was introduced in:
http://www.spinics.net/lists/netfilter-devel/msg13535.html
Since this change is not included in any stable Linux kernel,
I think it's safe to make this change now. Anyway, this copy
mode does not make any sense from user-space, so this patch
should not break any existing setup.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Check at rule install time that CT accounting is enabled. Force it
to be enabled if not while also emitting a warning since this is not
the default state.
This is in preparation for deprecating CONFIG_NF_CT_ACCT upon which
CONFIG_NETFILTER_XT_MATCH_CONNBYTES depended being set.
Added 2 CT accounting support functions:
nf_ct_acct_enabled() - Get CT accounting state.
nf_ct_set_acct() - Enable/disable CT accountuing.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Acked-by: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
2.6.34 introduced 'conntrack zones' to deal with cases where packets
from multiple identical networks are handled by conntrack/NAT. Packets
are looped through veth devices, during which they are NATed to private
addresses, after which they can continue normally through the stack
and possibly have NAT rules applied a second time.
This works well, but is needlessly complicated for cases where only
a single SNAT/DNAT mapping needs to be applied to these packets. In that
case, all that needs to be done is to assign each network to a seperate
zone and perform NAT as usual. However this doesn't work for packets
destined for the machine performing NAT itself since its corrently not
possible to configure SNAT mappings for the LOCAL_IN chain.
This patch adds a new INPUT chain to the NAT table and changes the
targets performing SNAT to be usable in that chain.
Example usage with two identical networks (192.168.0.0/24) on eth0/eth1:
iptables -t raw -A PREROUTING -i eth0 -j CT --zone 1
iptables -t raw -A PREROUTING -i eth0 -j MARK --set-mark 1
iptables -t raw -A PREROUTING -i eth1 -j CT --zone 2
iptabels -t raw -A PREROUTING -i eth1 -j MARK --set-mark 2
iptables -t nat -A INPUT -m mark --mark 1 -j NETMAP --to 10.0.0.0/24
iptables -t nat -A POSTROUTING -m mark --mark 1 -j NETMAP --to 10.0.0.0/24
iptables -t nat -A INPUT -m mark --mark 2 -j NETMAP --to 10.0.1.0/24
iptables -t nat -A POSTROUTING -m mark --mark 2 -j NETMAP --to 10.0.1.0/24
iptables -t raw -A PREROUTING -d 10.0.0.0/24 -j CT --zone 1
iptables -t raw -A OUTPUT -d 10.0.0.0/24 -j CT --zone 1
iptables -t raw -A PREROUTING -d 10.0.1.0/24 -j CT --zone 2
iptables -t raw -A OUTPUT -d 10.0.1.0/24 -j CT --zone 2
iptables -t nat -A PREROUTING -d 10.0.0.0/24 -j NETMAP --to 192.168.0.0/24
iptables -t nat -A OUTPUT -d 10.0.0.0/24 -j NETMAP --to 192.168.0.0/24
iptables -t nat -A PREROUTING -d 10.0.1.0/24 -j NETMAP --to 192.168.0.0/24
iptables -t nat -A OUTPUT -d 10.0.1.0/24 -j NETMAP --to 192.168.0.0/24
Signed-off-by: Patrick McHardy <kaber@trash.net>
gen_kill_estimator() API is incomplete or not well documented, since
caller should make sure an RCU grace period is respected before
freeing stats_lock.
This was partially addressed in commit 5d944c640b
(gen_estimator: deadlock fix), but same problem exist for all
gen_kill_estimator() users, if lock they use is not already RCU
protected.
A code review shows xt_RATEEST.c, act_api.c, act_police.c have this
problem. Other are ok because they use qdisc lock, already RCU
protected.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NOTRACK makes all cpus share a cache line on nf_conntrack_untracked
twice per packet, slowing down performance.
This patch converts it to a per_cpu variable.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
NOTRACK makes all cpus share a cache line on nf_conntrack_untracked
twice per packet. This is bad for performance.
__read_mostly annotation is also a bad choice.
This patch introduces IPS_UNTRACKED bit so that we can use later a
per_cpu untrack structure more easily.
A new helper, nf_ct_untracked_get() returns a pointer to
nf_conntrack_untracked.
Another one, nf_ct_untracked_status_or() is used by nf_nat_init() to add
IPS_NAT_DONE_MASK bits to untracked status.
nf_ct_is_untracked() prototype is changed to work on a nf_conn pointer.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
We currently dirty two cache lines in struct xt_rateest, this hurts SMP
performance.
This patch moves lock/bstats/rstats at beginning of structure so that
they share a single cache line.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use read_pnet() and write_pnet() to reduce number of ifdef CONFIG_NET_NS
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This race was triggered by a 'conntrack -F' command running in parallel
to the insertion of a hash for a new connection. Losing this race led to
a dead conntrack entry effectively blocking traffic for a particular
connection until timeout or flushing the conntrack hashes again.
Now the check for an already dying connection is done inside the lock.
Signed-off-by: Joerg Marx <joerg.marx@secunet.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
As reported by Randy Dunlap <randy.dunlap@oracle.com>, compilation
of nf_defrag_ipv4 fails with:
include/net/netfilter/nf_conntrack.h:94: error: field 'ct_general' has incomplete type
include/net/netfilter/nf_conntrack.h:178: error: 'const struct sk_buff' has no member named 'nfct'
include/net/netfilter/nf_conntrack.h:185: error: implicit declaration of function 'nf_conntrack_put'
include/net/netfilter/nf_conntrack.h:294: error: 'const struct sk_buff' has no member named 'nfct'
net/ipv4/netfilter/nf_defrag_ipv4.c:45: error: 'struct sk_buff' has no member named 'nfct'
net/ipv4/netfilter/nf_defrag_ipv4.c:46: error: 'struct sk_buff' has no member named 'nfct'
net/nf_conntrack.h must not be included with NF_CONNTRACK=n, add a
few #ifdefs. Long term the header file should be fixed to be usable
even with NF_CONNTRACK=n.
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Normally, each connection needs a unique identity. Conntrack zones allow
to specify a numerical zone using the CT target, connections in different
zones can use the same identity.
Example:
iptables -t raw -A PREROUTING -i veth0 -j CT --zone 1
iptables -t raw -A OUTPUT -o veth1 -j CT --zone 1
Signed-off-by: Patrick McHardy <kaber@trash.net>
The error handlers might need the template to get the conntrack zone
introduced in the next patches to perform a conntrack lookup.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Remove #ifdef at nf_ct_exp_net() by using nf_ct_net().
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
nf_nat_mangle_tcp_packet() can currently only handle a single mangling
per window because it only maintains two sequence adjustment positions:
the one before the last adjustment and the one after.
This patch makes sequence number adjustment tracking in
nf_nat_mangle_tcp_packet() optional and allows a helper to manually
update the offsets after the packet has been fully handled.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Make the output a bit more informative by showing the helper an expectation
belongs to and the expectation class.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add a new target for the raw table, which can be used to specify conntrack
parameters for specific connections, f.i. the conntrack helper.
The target attaches a "template" connection tracking entry to the skb, which
is used by the conntrack core when initializing a new conntrack.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Support initializing selected parameters of new conntrack entries from a
"conntrack template", which is a specially marked conntrack entry attached
to the skb.
Currently the helper and the event delivery masks can be initialized this
way.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add two masks for conntrack end expectation events to struct nf_conntrack_ecache
and use them to filter events. Their default value is "all events" when the
event sysctl is on and "no events" when it is off. A following patch will add
specific initializations. Expectation events depend on the ecache struct of
their master conntrack.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Split up the IPCT_STATUS event into an IPCT_REPLY event, which is generated
when the IPS_SEEN_REPLY bit is set, and an IPCT_ASSURED event, which is
generated when the IPS_ASSURED bit is set.
In combination with a following patch to support selective event delivery,
this can be used for "sparse" conntrack replication: start replicating the
conntrack entry after it reached the ASSURED state and that way it's SYN-flood
resistant.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Make sure not to assign a helper for a different network or transport
layer protocol to a connection.
Additionally change expectation deletion by helper to compare the name
directly - there might be multiple helper registrations using the same
name, currently one of them is chosen in an unpredictable manner and
only those expectations are removed.
Signed-off-by: Patrick McHardy <kaber@trash.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
ixgbe: allow tx of pre-formatted vlan tagged packets
ixgbe: Fix 82598 premature copper PHY link indicatation
ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
bcm63xx_enet: fix compilation failure after get_stats_count removal
packet: dont call sleeping functions while holding rcu_read_lock()
tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
ipvs: zero usvc and udest
netfilter: fix crashes in bridge netfilter caused by fragment jumps
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
sky2: leave PCI config space writeable
sky2: print Optima chip name
x25: Update maintainer.
ipvs: fix synchronization on connection close
netfilter: xtables: document minimal required version
drivers/net/bonding/: : use pr_fmt
can: CAN_MCP251X should depend on HAS_DMA
drivers/net/usb: Correct code taking the size of a pointer
drivers/net/cpmac.c: Correct code taking the size of a pointer
drivers/net/sfc: Correct code taking the size of a pointer
...
Currently the same reassembly queue might be used for packets reassembled
by conntrack in different positions in the stack (PREROUTING/LOCAL_OUT),
as well as local delivery. This can cause "packet jumps" when the fragment
completing a reassembled packet is queued from a different position in the
stack than the previous ones.
Add a "user" identifier to the reassembly queue key to seperate the queues
of each caller, similar to what we do for IPv4.
Signed-off-by: Patrick McHardy <kaber@trash.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Vitezslav Samel discovered that since 2.6.30.4+ active FTP can not work
over NAT. The "cause" of the problem was a fix of unacknowledged data
detection with NAT (commit a3a9f79e36).
However, actually, that fix uncovered a long standing bug in TCP conntrack:
when NAT was enabled, we simply updated the max of the right edge of
the segments we have seen (td_end), by the offset NAT produced with
changing IP/port in the data. However, we did not update the other parameter
(td_maxend) which is affected by the NAT offset. Thus that could drift
away from the correct value and thus resulted breaking active FTP.
The patch below fixes the issue by *not* updating the conntrack parameters
from NAT, but instead taking into account the NAT offsets in conntrack in a
consistent way. (Updating from NAT would be more harder and expensive because
it'd need to re-calculate parameters we already calculated in conntrack.)
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup patch puts struct/union/enum opening braces,
in first line to ease grep games.
struct something
{
becomes :
struct something {
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 5e140dfc1f "net: reorder struct Qdisc
for better SMP performance" the definition of struct gnet_stats_basic
changed incompatibly, as copies of this struct are shipped to
userland via netlink.
Restoring old behavior is not welcome, for performance reason.
Fix is to use a private structure for kernel, and
teach gnet_stats_copy_basic() to convert from kernel to user land,
using legacy structure (struct gnet_stats_basic)
Based on a report and initial patch from Michael Spang.
Reported-by: Michael Spang <mspang@csclub.uwaterloo.ca>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAT helpers change the TCP packet size, the highest seen sequence
number needs to be corrected. This is currently only done upwards, when
the packet size is reduced the sequence number is unchanged. This causes
TCP conntrack to falsely detect unacknowledged data and decrease the
timeout.
Fix by updating the highest seen sequence number in both directions after
packet mangling.
Tested-by: Krzysztof Piotr Oledzki <ole@ans.pl>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch improves ctnetlink event reliability if one broadcast
listener has set the NETLINK_BROADCAST_ERROR socket option.
The logic is the following: if an event delivery fails, we keep
the undelivered events in the missed event cache. Once the next
packet arrives, we add the new events (if any) to the missed
events in the cache and we try a new delivery, and so on. Thus,
if ctnetlink fails to deliver an event, we try to deliver them
once we see a new packet. Therefore, we may lose state
transitions but the userspace process gets in sync at some point.
At worst case, if no events were delivered to userspace, we make
sure that destroy events are successfully delivered. Basically,
if ctnetlink fails to deliver the destroy event, we remove the
conntrack entry from the hashes and we insert them in the dying
list, which contains inactive entries. Then, the conntrack timer
is added with an extra grace timeout of random32() % 15 seconds
to trigger the event again (this grace timeout is tunable via
/proc). The use of a limited random timeout value allows
distributing the "destroy" resends, thus, avoiding accumulating
lots "destroy" events at the same time. Event delivery may
re-order but we can identify them by means of the tuple plus
the conntrack ID.
The maximum number of conntrack entries (active or inactive) is
still handled by nf_conntrack_max. Thus, we may start dropping
packets at some point if we accumulate a lot of inactive conntrack
entries that did not successfully report the destroy event to
userspace.
During my stress tests consisting of setting a very small buffer
of 2048 bytes for conntrackd and the NETLINK_BROADCAST_ERROR socket
flag, and generating lots of very small connections, I noticed
very few destroy entries on the fly waiting to be resend.
A simple way to test this patch consist of creating a lot of
entries, set a very small Netlink buffer in conntrackd (+ a patch
which is not in the git tree to set the BROADCAST_ERROR flag)
and invoke `conntrack -F'.
For expectations, no changes are introduced in this patch.
Currently, event delivery is only done for new expectations (no
events from expectation expiration, removal and confirmation).
In that case, they need a per-expectation event cache to implement
the same idea that is exposed in this patch.
This patch can be useful to provide reliable flow-accouting. We
still have to add a new conntrack extension to store the creation
and destroy time.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch moves the helper destruction to a function that lives
in nf_conntrack_helper.c. This new function is used in the patch
to add ctnetlink reliable event delivery.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch reworks the per-cpu event caching to use the conntrack
extension infrastructure.
The main drawback is that we consume more memory per conntrack
if event delivery is enabled. This patch is required by the
reliable event delivery that follows to this patch.
BTW, this patch allows you to enable/disable event delivery via
/proc/sys/net/netfilter/nf_conntrack_events in runtime, although
you can still disable event caching as compilation option.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Introduce per-conntrack locks and use them instead of the global protocol
locks to avoid contention. Especially tcp_lock shows up very high in
profiles on larger machines.
This will also allow to simplify the upcoming reliable event delivery patches.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Current conntrack code kills the ICMP conntrack entry as soon as
the first reply is received. This is incorrect, as we then see only
the first ICMP echo reply out of several possible duplicates as
ESTABLISHED, while the rest will be INVALID. Also this unnecessarily
increases the conntrackd traffic on H-A firewalls.
Make all the ICMP conntrack entries (including the replied ones)
last for the default of nf_conntrack_icmp{,v6}_timeout seconds.
Signed-off-by: Jan "Yenya" Kasprzak <kas@fi.muni.cz>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch removes the notify chain infrastructure and replace it
by a simple function pointer. This issue has been mentioned in the
mailing list several times: the use of the notify chain adds
too much overhead for something that is only used by ctnetlink.
This patch also changes nfnetlink_send(). It seems that gfp_any()
returns GFP_KERNEL for user-context request, like those via
ctnetlink, inside the RCU read-side section which is not valid.
Using GFP_KERNEL is also evil since netlink may schedule(),
this leads to "scheduling while atomic" bug reports.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch simplifies the conntrack event caching system by removing
several events:
* IPCT_[*]_VOLATILE, IPCT_HELPINFO and IPCT_NATINFO has been deleted
since the have no clients.
* IPCT_COUNTER_FILLING which is a leftover of the 32-bits counter
days.
* IPCT_REFRESH which is not of any use since we always include the
timeout in the messages.
After this patch, the existing events are:
* IPCT_NEW, IPCT_RELATED and IPCT_DESTROY, that are used to identify
addition and deletion of entries.
* IPCT_STATUS, that notes that the status bits have changes,
eg. IPS_SEEN_REPLY and IPS_ASSURED.
* IPCT_PROTOINFO, that reports that internal protocol information has
changed, eg. the TCP, DCCP and SCTP protocol state.
* IPCT_HELPER, that a helper has been assigned or unassigned to this
entry.
* IPCT_MARK and IPCT_SECMARK, that reports that the mark has changed, this
covers the case when a mark is set to zero.
* IPCT_NATSEQADJ, to report that there's updates in the NAT sequence
adjustment.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch moves the event flags from linux/netfilter/nf_conntrack_common.h
to net/netfilter/nf_conntrack_ecache.h. This flags are not of any use
from userspace.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
During the module removal there are no possible event listeners
since ctnetlink must be removed before to allow removing
nf_conntrack. This patch removes the event reporting for the
module removal case which is not of any use in the existing code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
The removal of the SAME target accidentally removed one feature that is
not available from the normal NAT targets so far, having multi-range
mappings that use the same mapping for each connection from a single
client. The current behaviour is to choose the address from the range
based on source and destination IP, which breaks when communicating
with sites having multiple addresses that require all connections to
originate from the same IP address.
Introduce a IP_NAT_RANGE_PERSISTENT option that controls whether the
destination address is taken into account for selecting addresses.
http://bugzilla.kernel.org/show_bug.cgi?id=12954
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch fixes a regression (introduced by myself in commit 19abb7b:
netfilter: ctnetlink: deliver events for conntracks changed from
userspace) that results in an expectation re-insertion since
__nf_ct_expect_check() may return 0 for expectation timer refreshing.
This patch also removes a unnecessary refcount bump that
pretended to avoid a possible race condition with event delivery
and expectation timers (as said, not needed since we hold a
reference to the object since until we finish the expectation
setup). This also merges nf_ct_expect_related_report() and
nf_ct_expect_related() which look basically the same.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Usefull for all protocols which do not add additional data, such
as GRE or UDPlite.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Changli Gao