Pull input updates from Dmitry Torokhov:
"Updates for the input subsystem. You will get an new drivers for
Hyper-V synthetic keyboard and for Neonode zForce touchscreens, plus a
bunch of driver fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (49 commits)
Revert "Input: ALPS - add support for model found on Dell XT2"
arm: dts: am335x sk: add touchscreen support
Input: ti_am335x_tsc - fix spelling mistake in TSC/ADC DT binding
Input: cyttsp4 - replace IS_ERR and PTR_ERR with PTR_ERR_OR_ZERO
Input: mma8450 - add missing i2c_set_clientdata() in mma8450_probe()
Input: mpu3050 - add missing i2c_set_clientdata() in mpu3050_probe()
Input: tnetv107x-keypad - make irqs signed for error handling
Input: add driver for Neonode zForce based touchscreens
Input: sh_keysc - enable the driver on all ARM platforms
Input: remove a redundant max() call
Input: mousedev - allow disabling even without CONFIG_EXPERT
Input: allow deselecting serio drivers even without CONFIG_EXPERT
Input: i8042 - add PNP modaliases
Input: evdev - fall back to vmalloc for client event buffer
Input: cypress_ps2 - do not consider data bad if palm is detected
Input: cypress_ps2 - remove useless cast
Input: fix PWM-related undefined reference errors
Input: ALPS - change secondary device's name
Input: wacom - not all multi-interface devices support touch
Input: nspire-keypad - add missing clk_disable_unprepare() on error path
...
There was a spelling mistake on TSC/ADC binding where "coordinate" was
spelled as "coordiante".
We can't simply fix the error due to DT being an ABI, the approach taken
was to first use correct spelling and if that fails, fall back to
miss-spelled version.
It's unfortunate that has creeped into the tree.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The data structure of_match_ptr() protects is always compiled in.
Hence of_match_ptr() is not needed.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Enable shared IRQ to allow ADC to share IRQ line from
parent MFD core. Only FIFO0 IRQs are for TSC and handled
on the TSC side.
Step mask would be updated from cached variable only previously.
In rare cases when both TSC and ADC are used, the cached
variable gets mixed up.
The step mask is written with the required mask every time.
Rachna Patil (TI) laid ground work for shared IRQ.
Signed-off-by: Zubair Lutfullah <zubair.lutfullah@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator subdevice
addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need since
commit 0998d063.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJR2zCaAAoJEIqAPN1PVmxK29EP/ieZf7Z7z7bg/0lEOvtOzACy
WoCdSGFu5XcHOnlv0Fl1Rr/1AJFQoh4KugkGnVyrlztYVOFymj5VDdd8B43cxMLt
7ymK/3crIH7uJuOoeDoDr3glLuo0TGB9f5Kv4ITdVD3/+AuqY4VIAisEDb0aWghW
+v0I3fYeGdwRv+IqO5wacvddSoLa4rmOhnpbVMB2O1Y/LCm/yHI6tAFx1+AfH7y8
zMHbGFc+gHg1xupJBCnRel0v8J+KNc02G/B1zNom/avL8b/mNXNI8JFxs3bMA0r8
NpTHJ49OVPbhBQTA4U+BPoG4nzOiAOj0czf9dkGa5cyR8t4C9mmK+s8QHwepzrSG
qbhCgTqp4bomB1m0RAO+z4F6BHTpmoChpho2btrwN9ZmhMHQeTWnGjjhEwZngpBq
F22DC6k5ipV0k4962ZHfZ76v2Vot1gfd6zQ5r+2oHMMfWaKgS4L5efP2/wsU9H58
BxMm84C7OWbgcTRmNn9jl4L9phBD31wvNANfUeMhLMyshnwPK5ZuUdX/+K2rq6h9
w26Hg62HtKZFv/TEsCBQqpB6zSZa4u/KZzvwEahllQSQGKxIHaNYGtLGzJj9sCM+
baT/82DFKuEvKfJpUKSBMznImp4WNGEz+8s2w4m/Ssuf30GN2GHjM9Q4gcHJu2mk
7fTrsSHWYN+EHVzh1Zb8
=RqMp
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD update from Samuel Ortiz:
"For the 3.11 merge we only have one new MFD driver for the Kontron
PLD.
But we also have:
- Support for the TPS659038 PMIC from the palmas driver.
- Intel's Coleto Creek and Avoton SoCs support from the lpc_ich
driver.
- RTL8411B support from the rtsx driver.
- More DT support for the Arizona, max8998, twl4030-power and the
ti_am335x_tsadc drivers.
- The SSBI driver move under MFD.
- A conversion to the devm_* API for most of the MFD drivers.
- The twl4030-power got split from twl-core into its own module.
- A major ti_am335x_adc cleanup, leading to a proper DT support.
- Our regular arizona and wm* updates and cleanups from the Wolfson
folks.
- A better error handling and initialization, and a regulator
subdevice addition for the 88pm80x driver.
- A bulk platform_set_drvdata() call removal that's no longer need
since commit 0998d06310 ("device-core: Ensure drvdata = NULL when
no driver is bound")
* tag 'mfd-3.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (102 commits)
mfd: sec: Provide max_register to regmap
mfd: wm8994: Remove duplicate check for active JACKDET
MAINTAINERS: Add include directory to MFD file patterns
mfd: sec: Remove fields not used since regmap conversion
watchdog: Kontron PLD watchdog timer driver
mfd: max8998: Add support for Device Tree
regulator: max8998: Use arrays for specifying voltages in platform data
mfd: max8998: Add irq domain support
regulator: palmas: Add TPS659038 support
mfd: Kontron PLD mfd driver
mfd: palmas: Add TPS659038 PMIC support
mfd: palmas: Add SMPS10_BOOST feature
mfd: palmas: Check if irq is valid
mfd: lpc_ich: iTCO_wdt patch for Intel Coleto Creek DeviceIDs
mfd: twl-core: Change TWL6025 references to TWL6032
mfd: davinci_voicecodec: Fix build breakage
mfd: vexpress: Make the driver optional for arm and arm64
mfd: htc-egpio: Use devm_ioremap_nocache() instead of ioremap_nocache()
mfd: davinci_voicecodec: Convert to use devm_* APIs
mfd: twl4030-power: Fix relocking on error
...
The previous patch ("input/ti_am335x_tsc: ACK the HW_PEN irq in ISR")
acked the interrupt so we don't freeze if we don't handle an enabled
interrupt source. The interrupt core has a mechanism for this and to get
it work one should only say that it handled an interrupt if it is
actually the case.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The interrupt source IRQENB_HW_PEN is enabled in suspend and suposed to
be used as a wake up source. Once this interrupt source is unmaksed, the
devices ends up in ISR and never continues.
This change ACKs the interrupt and disables it so the system does not
freeze.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The driver programs a threshold of "coordinate_readouts" say 5. The
REG_FIFO0THR registers says it should it be programmed to "threshold
minus one". The driver does not expect just 5 coordinates but 5 * 2 + 2.
Multiplied by two because 5 for X and 5 for Y and plus 2 because we have
two Z.
The whole thing kind of works because It reads the 5 coordinates for X
and Y from FIFO0 and FIFO1 and the last element in each FIFO is ignored
within the loop and read later.
Nothing guaranties that FIFO1 is ready by the time it is read. In fact I
could see that that FIFO1 reaturns for Y channels 8,9, 10, 12, 6 and for
Y channel 7 for Z. The problem is that channel 7 and channel 12 got
somehow mixed up.
The other Problem is that FIFO1 is also used by the IIO part leading to
wrong results if both (tsc & adc) are used.
The patch tries to clean up the whole thing a little:
- Remove the +1 and -1 in REG_STEPCONFIG, REG_STEPDELAY and its counter
part in the for loop. This is just confusing.
- Use only FIFO0 in TSC. The fifo has space for 64 entries so should be
fine.
- Read the whole FIFO in one function and check the channel.
- in case we dawdle around, make sure we only read a multiple of our
coordinate set. On the second interrupt we will cleanup the remaining
enties.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch removes access to platform data mfd_tscadc_board because the
platform is DT only.
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
This patch adds DT support to touch driver. It also provides a binding
document which is used by the MFD and IIO part of the device.
This patch also renames steps_to_configure to coordinate_readouts
because the original name misleads the purpose of the variable.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
When touchscreen and ADC are used together, this
unwanted fifo flush leads to loss of ADC data.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The current driver expected touchscreen input
wires(XP,XN,YP,YN) to be connected in a particular order.
Making changes to accept this as platform data.
Sebastian reworked the original patch and removed a lot of the not
required pieces.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Current code has hard coded value written to
step enable bits. Now the bits are updated based
on how many steps are needed to be configured got
from platform data.
The user needs to take care not to exceed
the count more than 16. While using ADC and TSC
one should take care to set this parameter correctly.
Sebastian added the common lock and moved the code, that manipulates the
steps, from into the mfd module.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
The mfd driver creates platform data for the child devices and it is the
ti_tscadc_dev struct. This struct is copied for the two devices.
The copy of the structure makes a common lock in this structure a little
less usefull. Therefore the platform data is not a pointer to the
structure and the same structure is used.
While doing the change I noticed that the suspend/resume code assumes
the wrong pointer for ti_tscadc_dev and this has been fixed as well.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Commit 0998d06310 (device-core: Ensure drvdata = NULL when no
driver is bound) removes the need to set driver data field to
NULL.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull second round of input updates from Dmitry Torokhov:
"As usual, there are a couple of new drivers, input core now supports
managed input devices (devres), a slew of drivers now have device tree
support and a bunch of fixes and cleanups."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits)
Input: walkera0701 - fix crash on startup
Input: matrix-keymap - provide a proper module license
Input: gpio_keys_polled - switch to using gpio_request_one()
Input: gpio_keys - switch to using gpio_request_one()
Input: wacom - fix touch support for Bamboo Fun CTH-461
Input: xpad - add a few new VID/PID combinations
Input: xpad - minor formatting fixes
Input: gpio-keys-polled - honor 'autorepeat' setting in platform data
Input: tca8418-keypad - switch to using managed resources
Input: tca8418_keypad - increase severity of failures in probe()
Input: tca8418_keypad - move device ID tables closer to where they are used
Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data
Input: tca8418_keypad - use a temporary variable for parent device
Input: tca8418_keypad - add support for shared interrupt
Input: tca8418_keypad - add support for device tree bindings
Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver
Input: bu21013_ts - add support for Device Tree booting
Input: bu21013_ts - move GPIO init and exit functions into the driver
Input: bu21013_ts - request regulator that actually exists
ARM: ux500: Strip out duplicate touch screen platform information
...
This patch converts touchscreen into a MFD client.
All the register definitions, clock initialization,
etc has been moved to MFD core driver.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make way for addition of MFD driver.
The existing touchsreen driver is a MFD client.
For better readability we rename the file to
indicate its functionality as only touchscreen.
Signed-off-by: Patil, Rachna <rachna@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Linus Torvalds