Since some of the AST2600 pinconf setting are not just single bit, modified
aspeed_pin_config @bit to @mask and add @mask to aspeed_pin_config_map to
support configuring multiple bits.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-7-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2600 pinconf differs from the 2400 and 2500, aspeed_pin_config_map
should define separately, and add @confmaps and @nconfmaps to
aspeed_pinctrl_data structure for that change.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-6-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This helper macro is for declaring single bit (SB) mask pinconf,
and is used to prepare for modifying aspeed_pin_config
structure, the aspeed_pin_config structure @bit variable will be
modified to @mask.
This case is common in the AST2400/AST2500 which the mask is a single bit.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191202061432.3996-5-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to
the Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver.
-----BEGIN PGP SIGNATURE-----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=2nNz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.4 kernel cycle:
Core changes:
- Fix errors in example code in the documentation.
New drivers:
- Add support for JZ4760, JZ4760B, X1000, X1000E and X1500 to the
Ingenic driver.
- Support Cirrus Logic Madera CS47L92 and CS47L15.
- Support Allwinner Sunxi V3S.
- Support Aspeed 2600 BMC.
- Support Qualcomm SC7180.
- Support Marvell MVEBU CS115.
Driver improvements:
- Clean up a few drivers to use the devm_platform_ioremap_resource()
helper.
- Pass the irqchip when registering the gpio_chip in some pin
controllers that are also GPIO controllers.
- Support suspend/resume in the Tegra driver.
- Support pull-up on the Broadcom BCM2711.
- The Intel driver can now request locked pads.
- Fix the UFS reset pin in the Qualcomm SDM845 driver"
* tag 'pinctrl-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (112 commits)
pinctrl: meson-gxbb: Fix wrong pinning definition for uart_c
pinctrl: sh-pfc: Unlock on error in sh_pfc_func_set_mux()
pinctrl: bcm: remove redundant assignment to pointer log
pinctrl: iproc: Add 'get_direction' support
pinctrl: iproc-gpio: Handle interrupts for multiple instances
pinctrl: iproc-gpio: Fix incorrect pinconf configurations
pinctrl: intel: mark intel_pin_to_gpio __maybe_unused
pinctrl: qcom: sdm845: Fix UFS_RESET pin
pinctrl: mvebu: add additional variant for standalone CP115
pinctrl: mvebu: Add CP110 missing pin functionality
dt-bindings: cp110: document the new CP115 pinctrl compatible
pinctrl: bcm2835: Pass irqchip when adding gpiochip
pinctrl: meson: meson: Add of_node_put() before return
pinctrl/gpio: Take MUX usage into account
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150l support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150b support
dt-bindings: pinctrl: qcom-pmic-gpio: Add pm8150 support
pinctrl: amd: disable spurious-firing GPIO IRQs
pinctrl: rza2: Include the appropriate headers
pinctrl: rza2: Drop driver use of consumer flags
...
Commit 674fa8daa8 ("pinctrl: aspeed-g5: Delay acquisition of regmaps")
was determined to be a partial fix to the problem of acquiring the LPC
Host Controller and GFX regmaps: The AST2500 pin controller may need to
fetch syscon regmaps during expression evaluation as well as when
setting mux state. For example, this case is hit by attempting to export
pins exposing the LPC Host Controller as GPIOs.
An optional eval() hook is added to the Aspeed pinmux operation struct
and called from aspeed_sig_expr_eval() if the pointer is set by the
SoC-specific driver. This enables the AST2500 to perform the custom
action of acquiring its regmap dependencies as required.
John Wang tested the fix on an Inspur FP5280G2 machine (AST2500-based)
where the issue was found, and I've booted the fix on Witherspoon
(AST2500) and Palmetto (AST2400) machines, and poked at relevant pins
under QEMU by forcing mux configurations via devmem before exporting
GPIOs to exercise the driver.
Fixes: 7d29ed88ac ("pinctrl: aspeed: Read and write bits in LPC and GFX controllers")
Fixes: 674fa8daa8 ("pinctrl: aspeed-g5: Delay acquisition of regmaps")
Reported-by: John Wang <wangzqbj@inspur.com>
Tested-by: John Wang <wangzqbj@inspur.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190829071738.2523-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Otherwise they look odd in the face of not being listed in the bindings
documents.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190724081313.12934-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AST2400 and AST2500 SoCs only exposed one pin group per function.
Lone pin groups drove some implementation simplifications in the ASPEED
pinmux infrastructure that is now invalid for the AST2600, which
supports multiple groups per function for some functions on the chip
(SMBus Alert pins and UARTs among others).
This patch reworks the macro jungle to enable support for multiple pin
groups. In the process we inflict some collateral damage on the existing
AST2400 and AST2500 drivers, but the rework is mostly a relatively
straight-forward, automated transform of adding the pin name as an
argument to some macro calls and implementing wrappers to paper over
groups in the cases where there aren't multiple.
As previously documented, the macro infrastructure exposes mux
configuration as symbols in the source file which are used to detect
accidental duplication. Previously these symbols were named in terms of
the signal for a given expression. As the AST2600 supports multiple pin
groups for a function, the signal name on its own is no-longer unique,
and we must switch to the (signal, group) tuple. However, this means
that we can no-longer derive the signal expression symbol name from the
signal name alone, which among other cases, impacts the operation of the
PIN_DECL_x() macros.
To fix that and avoid requiring we awkwardly provide the associated
group name for every signal for every PIN_DECL_x() invocation, instead
opportunistically alias the name of the signal expression symbol from
the unique (signal, group) tuple to the also unique (pin, signal) tuple,
then reference the alias symbol in the tables generated by PIN_DECL_x().
This way we do not require extra group parameters for PIN_DECL_x() as
the pin name was already provided as an argument, and instead simply
require that the pin name be provided to the expression declaration
macros in order to generate the alias symbol.
The patch implements the alias strategy and fixes up all the expression
definition macro calls in the AST2400 and AST2500 drivers to account for
pin groups. Given the implementation strategy has the property that
compilation either fails or loudly warns for bad pin descriptions, this
patch is theoretically tested by successfully compiling both affected
drivers. For a more practical test I've inspected the diff of the
content of the pinctrl debugfs entries before and after the patch under
qemu; all pins, functions and groups match.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190729055604.13239-5-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename macros as follows:
* s/SS_PIN_DECL()/PIN_DECL_1()/
* s/MS_PIN_DECL()/PIN_DECL_2()/
* s/MS_PIN_DECL_()/PIN_DECL_()/
This is in preparation for adding PIN_DECL_3(). We could clean this up
with e.g. CPPMAGIC_MAP() from ccan, but that might be a bridge too far
given how much of a macro jungle we already have.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190729055604.13239-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While sorting out some devicetree issues I found that the pinctrl driver
was failing to acquire its GFX regmap even though the phandle was
present in the devicetree:
[ 0.124190] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: No GFX phandle found, some mux configurations may fail
Without access to the GFX regmap we fail to configure the mux for the
VPO function:
[ 1.548866] pinctrl core: add 1 pinctrl maps
[ 1.549826] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: found group selector 164 for VPO
[ 1.550638] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 144 (V20) for 1e6e6000.display
[ 1.551346] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 145 (U19) for 1e6e6000.display
...
[ 1.562057] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 218 (T22) for 1e6e6000.display
[ 1.562541] aspeed-g5-pinctrl 1e6e2000.syscon:pinctrl: request pin 219 (R20) for 1e6e6000.display
[ 1.563113] Muxing pin 144 for VPO
[ 1.563456] Want SCU8C[0x00000001]=0x1, got 0x0 from 0x00000000
[ 1.564624] aspeed_gfx 1e6e6000.display: Error applying setting, reverse things back
This turned out to be a simple problem of timing: The ASPEED pinctrl
driver is probed during arch_initcall(), while GFX is processed much
later. As such the GFX syscon is not yet registered during the pinctrl
probe() and we get an -EPROBE_DEFER when we try to look it up, however
we must not defer probing the pinctrl driver for the inability to mux
some GFX-related functions.
Switch to lazily grabbing the regmaps when they're first required by the
mux configuration. This generates a bit of noise in the patch as we have
to drop the `const` qualifier on arguments for several function
prototypes, but has the benefit of working.
I've smoke tested this for the ast2500-evb under qemu with a dummy
graphics device. We now succeed in our attempts to configure the SoC's
VPO pinmux function.
Fixes: 7d29ed88ac ("pinctrl: aspeed: Read and write bits in LPC and GFX controllers")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190724080155.12209-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cycle:
Core changes:
- Device links can optionally be added between a pin control
producer and its consumers. This will affect how the system
power management is handled: a pin controller will not suspend
before all of its consumers have been suspended. This was
necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense
to make this default in the long run. Right now it is
opt-in per driver.
- Drive strength can be specified in microamps. With decreases
in silicon technology, milliamps isn't granular enough, let's
make it possible to select drive strengths in microamps. Right
now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a
product line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in
addition to muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken
aside and not usable for users. This is used in ACPI systems
to take out some GPIO lines used by the BIOS so that
noone else (neither kernel nor userspace) will play with them
by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board
management controllers for servers) in preparation for the
new Aspeed AST2600 SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes.
-----BEGIN PGP SIGNATURE-----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=Wdw1
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.3 kernel cycle:
Core changes:
- Device links can optionally be added between a pin control producer
and its consumers. This will affect how the system power management
is handled: a pin controller will not suspend before all of its
consumers have been suspended.
This was necessary for the ST Microelectronics STMFX expander and
need to be tested on other systems as well: it makes sense to make
this default in the long run.
Right now it is opt-in per driver.
- Drive strength can be specified in microamps. With decreases in
silicon technology, milliamps isn't granular enough, let's make it
possible to select drive strengths in microamps.
Right now the Meson (AMlogic) driver needs this.
New drivers:
- New subdriver for the Tegra 194 SoC.
- New subdriver for the Qualcomm SDM845.
- New subdriver for the Qualcomm SM8150.
- New subdriver for the Freescale i.MX8MN (Freescale is now a product
line of NXP).
- New subdriver for Marvell MV98DX1135.
Driver improvements:
- The Bitmain BM1880 driver now supports pin config in addition to
muxing.
- The Qualcomm drivers can now reserve some GPIOs as taken aside and
not usable for users. This is used in ACPI systems to take out some
GPIO lines used by the BIOS so that noone else (neither kernel nor
userspace) will play with them by mistake and crash the machine.
- A slew of refurbishing around the Aspeed drivers (board management
controllers for servers) in preparation for the new Aspeed AST2600
SoC.
- A slew of improvements over the SH PFC drivers as usual.
- Misc cleanups and fixes"
* tag 'pinctrl-v5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (106 commits)
pinctrl: aspeed: Strip moved macros and structs from private header
pinctrl: aspeed: Fix missed include
pinctrl: baytrail: Use GENMASK() consistently
pinctrl: baytrail: Re-use data structures from pinctrl-intel.h
pinctrl: baytrail: Use defined macro instead of magic in byt_get_gpio_mux()
pinctrl: qcom: Add SM8150 pinctrl driver
dt-bindings: pinctrl: qcom: Add SM8150 pinctrl binding
dt-bindings: pinctrl: qcom: Document missing gpio nodes
pinctrl: aspeed: Add implementation-related documentation
pinctrl: aspeed: Split out pinmux from general pinctrl
pinctrl: aspeed: Clarify comment about strapping W1C
pinctrl: aspeed: Correct comment that is no longer true
MAINTAINERS: Add entry for ASPEED pinctrl drivers
dt-bindings: pinctrl: aspeed: Convert AST2500 bindings to json-schema
dt-bindings: pinctrl: aspeed: Convert AST2400 bindings to json-schema
dt-bindings: pinctrl: aspeed: Split bindings document in two
pinctrl: qcom: Add irq_enable callback for msm gpio
pinctrl: madera: Fixup SPDX headers
pinctrl: qcom: sdm845: Fix CONFIG preprocessor guard
pinctrl: tegra: Add bitmask support for parked bits
...
ASPEED have completely rearranged the System Control Unit register
layout with the AST2600. The existing code took advantage of the fact
that the AST2400 and AST2500 had layouts that were similar enough to
have little impact on the pinmux infrastructure (though there is a wart
with read-modify-write vs write-1-clear semantics of the hardware
strapping registers between the two).
Given that any similarity has been thrown out with the AST2600, separate
out the function applying an expression state to be driver-specific.
With it, extract out the pinmux macro jungle to its own header and
implementation so the pieces can be composed without dependency cycles.
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20190628023838.15426-8-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SGPM pinmux to ast2500-pinctrl function and group, to prepare for
supporting SGPIO in AST2500 SoC.
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These structures are only stored in fields of a pinctrl_desc
structure (confops, pctlops, and pmxops) that are const. Make the
structures const as well.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Implement the AST2500 USB functions as described by the devicetree
bindings. The AST2500 exposes five USB controllers through two USB
ports. Similar to the AST2400, the pins exposing USB are outliers with
respect to the rest of the pinmux as they not capable of GPIO.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Testing for pinctrl-aspeed-g5 was performed on an AST2500EVB system,
using the strategy outlined in the commit message for the change to the
Aspeed pinctrl core.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The patch introducing the g5 pinctrl driver implemented a smattering of
pins to flesh out the implementation of the core and provide bare-bones
support for some OpenPOWER platforms and the AST2500 evaluation board.
Now, update the bindings document to reflect the complete functionality
and implement the necessary pin configuration tables in the driver.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The System Control Unit IP block in the Aspeed SoCs is typically where
the pinmux configuration is found, but not always. A number of pins
depend on state in one of LPC Host Control (LHC) or SoC Display
Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
means to adjust these as necessary.
We use syscon to cast a regmap over the GFX and LPC blocks, which is
used as an arbitration layer between the relevant driver and the pinctrl
subsystem. The regmaps are then exposed to the SoC-specific pinctrl
drivers by phandles in the devicetree, and are selected during a mux
request by querying a new 'ip' member in struct aspeed_sig_desc.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a pin depending on bit 6 in SCU90 is requested for GPIO, the export
will succeed but changes to the GPIO's value will not be accepted by the
hardware. This is because the pinmux driver has misconfigured the SCU by
writing 1 to the reserved bit.
The description of SCU90[6] from the datasheet is 'Reserved, must keep
at value ”0”'. The fix is to switch pinmux from the bit-flipping macro
to explicitly configuring the .enable and .disable values to zero.
The patch has been tested on an AST2500 EVB.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Uma Yadlapati <yadlapat@us.ibm.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPI1 function was associated with the wrong pins: The functions that
those pins provide is either an SPI debug or passthrough function
coupled to SPI1. Make the SPI1 mux function configure the relevant pins
and associate new SPI1DEBUG and SPI1PASSTHRU functions with the pins
that were already defined.
The notation used in the datasheet's multi-function pin table for the SoC is
often creative: in this case the SYS* signals are enabled by a single bit,
which is nothing unusual on its own, but in this case the bit was also
participating in a multi-bit bitfield and therefore represented multiple
functions. This fact was overlooked in the original patch.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This prevented C20 from successfully being muxed as GPIO.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixes simple typos in the initial commit. There is no behavioural
change.
Fixes: 56e57cb6c0 (pinctrl: Add pinctrl-aspeed-g5 driver)
Reported-by: Xo Wang <xow@google.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A small subset of pins and functions are exposed. The selection of pins
and functions is driven by the development of OpenBMC[1] on the
AST2500 SoC, particularly around booting the IBM Witherspoon platform.
[1] https://github.com/openbmc/docs
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Johnny Huang