Since the new AR9003 EEPROM code does tune the card for the configured
tx power level, we need to fill in the correct power limits in the TPC
part of the DMA descriptor.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Combine multiple checks that were supposed to check for the same
conditions, but didn't. Always enable fast PLL clock on AR9280 2.0
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fast clock operation (44Mhz) is enabled for 5Ghz in ar9003, so
take care of the conversion from usec to hw clock.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable TX IQ calibration, it was prematurely enabled in
previous versions.
Cc: Paul Shaw <Paul.Shaw@Atheros.com>
Cc: Thomas Hammel <Thomas.Hammel@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This synchs up the initvals to the values used on the
Atheros HAL for AR9003. This specific change adds support
for a new high power module.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A misplaced interface type check bails out too early if the interface
is not in monitor mode. This patch moves it to the right place, so that
it only covers changes to the monitor flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A bunch of validation and processing in the RX IRQ handler
can be moved to the RX tasklet. The IRQ handler is
already heavy, with the memory allocation for handling
stream mode. Also, a memcpy of 40 bytes for every packet
can be avoided in the handler.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check for the endpoint IDs when processing
TX completions and drop the unsupported EPIDs.
We can add other endpoints (UAPSD,..) when support
is added.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the same type of configurable debug messages to libertas_tf as
already exist in the libertas driver. This has facilitated creation
of a interface specification and will facilitate future development
of this driver.
Signed-off-by: Steve deRosier <steve@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Restore the rfcsr initialization for RT305x SoC devices which was removed
by "rt2x00: Finish rt3070 support in rt2800 register initialization.".
This fixes the rx path on SoC devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix a typo in a comment in rt2800.h. Instead of replacing the wrong
hexvalue (0x171c) with the correct one (0x1718) just use the appropriate
readable define.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In kernel Bugzilla #15825, a case where routine ssb_bus_pcibus_register()
fails silently is reported. The cause for the failure is still being
investigated; however, the diagnosis would be easier if the failure
had been reported.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Get closer to what the ralink driver does by setting the rf register 13
to tx_power2 during channel switch.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Disable HT40 support for now as it causes rx problems with HT40 capable
11n APs (when mac80211 enables HT40, rx is completely disfunctional).
Once the rt2800 HT code is capable of using HT40 we should enable the
flag again.
I only tested this patch with a rt305x SoC device, nevertheless the
patch disables HT40 also on PCI and USB rt2800 devices.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All commands to the target are disabled when the device
is unplugged, but a normal module unload has to be
differentiated from this case, as we could still receive
data in the RX endpoint. Fix this by checking if the
device is attached or not.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My patch "ath9k_htc: Handle WMI timeouts properly" introduced
a race condition in WMI command processing. The last issued command
should be stored _before_ issuing a WMI command. Not doing this
would result in the WMI event IRQ dropping correct command responses
as invalid.
Fix this race by storing the command id correctly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Completion of WMI commands take a longer time
on some platforms. Increase the timeout value
to handle this.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When handling the REGIN callback, processing
the incoming data first should be the preferred
mode of operation. Allocation of a new SKB may fail,
in which case, the URB will not be resubmitted.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So, apparently there is a USB reboot command
that the target accepts. Using this instead of
usb_reset_device() fixes the issue of "descriptor read error"
that pops up on repeated load/unload.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the TX callback, the HTC layer has to pass the
priv pointer that was registered during service initialization.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason to disable the PHY Error / MIB counters
when the module is being unloaded.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a code segment in configpciepowersave()
to make use of multiple register writes.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the USB device has been unplugged, there is
no point in trying to send commands to the target.
Fix this by denying all WMI commands in such a case.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies URB management for transmission,
by removing the 'FLUSH' variable (which is not needed,
since we can determine if the URB has been killed by
looking at the URB status), and also handling the STOP
case properly.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a recently introduced use-after-free regression
from "p54pci: prevent stuck rx-ring on slow system".
Hans de Goede reported a use-after-free regression:
>BUG: unable to handle kernel paging request at 6b6b6b6b
>IP: [<e122284a>] p54p_check_tx_ring+0x84/0xb1 [p54pci]
>*pde = 00000000
>Oops: 0000 [#1] SMP
>EIP: 0060:[<e122284a>] EFLAGS: 00010286 CPU: 0
>EIP is at p54p_check_tx_ring+0x84/0xb1 [p54pci]
>EAX: 6b6b6b6b EBX: df10b170 ECX: 00000003 EDX: 00000001
>ESI: dc471500 EDI: d8acaeb0 EBP: c098be9c ESP: c098be84
> DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
>Process swapper (pid: 0, ti=c098a000 task=c09ccfe0 task.ti=c098a000)
>Call Trace:
> [<e1222b02>] ? p54p_tasklet+0xaa/0xb5 [p54pci]
> [<c0440568>] ? tasklet_action+0x78/0xcb
> [<c0440ed3>] ? __do_softirq+0xbc/0x173
Quote from comment #17:
"The problem is the innocent looking moving of the tx processing to
after the rx processing in the tasklet. Quoting from the changelog:
This patch does it the same way, except that it also prioritize
rx data processing, simply because tx routines *can* wait.
This is causing an issue with us referencing already freed memory,
because some skb's we transmit, we immediately receive back, such
as those for reading the eeprom (*) and getting stats.
What can happen because of the moving of the tx processing to after
the rx processing is that when the tasklet first runs after doing a
special skb tx (such as eeprom) we've already received the answer
to it.
Then the rx processing ends up calling p54_find_and_unlink_skb to
find the matching tx skb for the just received special rx skb and
frees the tx skb.
Then after the processing of the rx skb answer, and thus freeing
the tx skb, we go process the completed tx ring entires, and then
dereference the free-ed skb, to see if it should free free-ed by
p54p_check_tx_ring()."
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hans de Goede identified a bug in p54p_check_tx_ring:
there are two ring indices. 1 => tx data and 3 => tx management.
But the old code had a constant "1" and this resulted in spurious
dma unmapping failures.
Cc: stable@kernel.org
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=583623
Bug-Identified-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sta->last_tx_rate is traditionally updated just before transmitting a
frame based on information from the rate control algorithm. However, for
hardware drivers with IEEE80211_HW_HAS_RATE_CONTROL this is not performed,
as the rate control algorithm is not executed, and because the used rate is
not known before the frame has actually been transmitted.
This causes atleast a fixed 1Mb/s to be reported to user space. A few other
instances of code also rely on this information.
Fix this by setting the sta->last_tx_rate in tx_status handling. There, look
for last rates entry set by the driver, and use that as value for
sta->last_tx_rate.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Our offset handling becomes even a little more hackish now. For some reason I
do not understand all offsets as inrelative. It assumes base offset is 0x1000
but it will work for now as we make offsets relative anyway by removing base
0x1000. Should be cleaner however.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Attempting to read registers that don't exist on the SSB bus can cause
hangs on some boxes. At least some b43 devices are 'in the wild' that
don't have SPROMs at all. When the SSB bus support loads, it attempts
to read these (non-existant) SPROMs and causes hard hangs on the box --
no console output, etc.
This patch adds some intelligence to determine whether or not the SPROM
is present before attempting to read it. This avoids those hard hangs
on those devices with no SPROM attached to their SSB bus. The
SSB-attached devices (e.g. b43, et al.) won't work, but at least the box
will survive to test further patches. :-)
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Michael Buesch <mb@bu3sch.de>
When I updated this from the corresponding
userspace library, an annotation error crept
in -- this variable needs to be annotated as
little endian. No effect on code generation.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes ar5416Addac_9160 and ar5416Addac_9160 const
I guess we skipped them long ago.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When IEEE80211_HW_CONNECTION_MONITOR is configured by the driver, starting
of ieee80211_sta_conn_mon_timer should be prevented, as it is then not needed.
This is currently partially the case. As it seems, when a probe-response is
received from the AP the timer is still restarted, thus restarting the host
based connection keep-alive mechanism. These probe-responses happen at least
when scanning while associated.
Fix this by preventing starting of the ieee80211_sta_conn_mon_timer in the
ieee80211_rx_mgmt_probe_resp function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Supported only for single stream rates by the hardware
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9300 based hardware can 3x3 MCS rates, this should be set in the
HT capabilities.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of increasing bits_per_symbol for supporting more streams, keep
it single-stream only and multiply the values by the numer of streams.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Include MCS0-31 and also add SGI for HT20. This makes it
possible to support more different rate combinations with
newer hardware.
Based on a patch by Selvam. T.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau